While it may sometimes be convenient to export an NFS filesystem with
no_root_squash it should not be the default behavior. Align the
default behavior with the Linux NFS server defaults. To restore
the previous behavior use 'zfs set sharenfs="no_root_squash,..."'.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9397Closes#9425
After commit 5e74ac51 which split and reordered the run files the
`zpool_status_-s` test began failing. The new ordering placed
the test after a previous test which used `zpool replace` to replace
a disk but did not clear its label. This resulted in the next test,
`zpool_status_-s`, failing because of the potentially active
pool being detected on the replaced vdev.
/dev/loop0 is part of potentially active pool 'testpool'
Use the default_mirror_setup_noexit() and default_cleanup_noexit()
functions to create the pool in `zpool_status_-s`. They use the -f
flag by default.
In the `scrub_after_resilver` test wipe the label during cleanup
to prevent future failures if the tests are again reordered.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9451
Since 0.7.0, zpool import would unconditionally block on udev for 30
seconds. This introduced a regression in initramfs environments that
lack udev (particularly mdev based environments), yet use a zfs userland
tools intended for the system that had been built against udev. Gentoo's
genkernel is the main example, although custom user initramfs
environments would be similarly impacted unless special builds of the
ZFS userland utilities were done for them. Such environments already
have their own mechanisms for blocking until device nodes are ready
(such as genkernel's scandelay parameter), so it is unnecessary for
zpool import to block on a non-existent udev until a timeout is reached
inside of them.
Rather than trying to intelligently determine whether udev is available
on the system to avoid unnecessarily blocking in such environments, it
seems best to just allow the environment to override the timeout. I
propose that we add an environment variable called
ZPOOL_IMPORT_UDEV_TIMEOUT_MS. Setting it to 0 would restore the 0.6.x
behavior that was more desirable in mdev based initramfs environments.
This allows the system user land utilities to be reused when building
mdev-based initramfs archives.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#9436
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9445
Mostly whitespace changes, no functional changes intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9447
When "feature@allocation_classes" is not enabled on the pool no vdev
with "special" or "dedup" allocation type should be allowed to exist in
the vdev tree.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9427Closes#9429
Update the zfs(8) man page to clearly describe that arguments for
channel programs are to be listed after the -- sentinel which
terminates argument processing. This behavior is supported by
getopt on Linux, FreeBSD, and Illumos according to each platforms
respective man pages.
zfs program [-jn] [-t instruction-limit] [-m memory-limit]
pool script [--] arg1 ...
Reviewed-by: Clint Armstrong <clint@clintarmstrong.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9056Closes#9428
Correctly use the `mntpnt_fs` variable, and include additional
logic to ensure the /etc/hostid is correct set up and cleaned up.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9349
If stdin if empty - don't run xargs command,
otherwise we can get `cp: missing file operand`
error.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#9418
There have been occasional CI failures which occur when the trimmed
vdev size exactly matches the target size. Resolve this by slightly
relaxing the conditional and checking for -ge rather than -gt. In
all of the cases observer, the values match exactly. For example:
Failure /mnt/trim-vdev1 is 768 MB which is not -gt than 768 MB
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9399
Commit 093bb64 resolved an automount failures for chroot'd processes
but inadvertently broke automounting for root filesystems where the
vfs_mntpoint is NULL. Resolve the issue by checking for NULL in order
to generate the correct path.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9381Closes#9384
A rangelock KPI already exists on FreeBSD. Add a zfs_ prefix as
per our convention to prevent any conflict with existing symbols.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9402
Update cleanup_upgrade to use destroy_dataset and destroy_pool
when performing cleanup. These wrappers retry if the pool is busy
preventing occasional failures like those observed when running
tests upgrade_readonly_pool. For example:
SUCCESS: test enabled == enabled
User accounting upgrade is not executed on readonly pool
NOTE: Performing local cleanup via log_onexit (cleanup_upgrade)
cannot destroy 'testpool': pool is busy
ERROR: zpool destroy testpool exited 1
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9400
If /var/lib is a dataset not under <pool>/ROOT/<root_dataset>, as
proposed in the ubuntu root on zfs upstream guide
(https://github.com/zfsonlinux/zfs/wiki/Ubuntu-18.04-Root-on-ZFS),
we end up with a race where some services, like systemd-random-seed
are writing under /var/lib, while zfs-mount is called. zfs mount will
then potentially fail because of /var/lib isn't empty and so, can't be
mounted.
Order those 2 units for now (more may be needed) as we can't declare
virtually a provide mount point to match
"RequiresMountsFor=/var/lib/systemd/random-seed" from
systemd-random-seed.service.
The optional generator for zfs 0.8 fixes it, but it's not enabled
by default nor necessarily required.
Example:
- rpool/ROOT/ubuntu (mountpoint = /)
- rpool/var/ (mountpoint = /var)
- rpool/var/lib (mountpoint = /var/lib)
Both zfs-mount.service and systemd-random-seed.service are starting
After=systemd-remount-fs.service. zfs-mount.service should be done
before local-fs.target while systemd-random-seed.service should finish
before sysinit.target (which is a later target).
Ideally, we would have a way for zfs mount -a unit to declare all paths
or move systemd-random-seed after local-fs.target.
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Didier Roche <didrocks@ubuntu.com>
Closes#9360
Line 31 and 32 overwrote the ${root} variable which broke mount-zfs.sh
We have create a new variable for the dataset instead of overwriting the
${root} variable in zfs-load-key.sh${root} variable in zfs-load-key.sh
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dacian Reece-Stremtan <dacianstremtan@gmail.com>
Closes#8913Closes#9379
Reduce the time required for ./configure to perform the needed
KABI checks by allowing kbuild to compile multiple test cases in
parallel. This was accomplished by splitting each test's source
code from the logic handling whether that code could be compiled
or not.
By introducing this split it's possible to minimize the number of
times kbuild needs to be invoked. As importantly, it means all of
the tests can be built in parallel. This does require a little extra
care since we expect some tests to fail, so the --keep-going (-k)
option must be provided otherwise some tests may not get compiled.
Furthermore, since a failure during the kbuild modpost phase will
result in an early exit; the final linking phase is limited to tests
which passed the initial compilation and produced an object file.
Once everything has been built the configure script proceeds as
previously. The only significant difference is that it now merely
needs to test for the existence of a .ko file to determine the
result of a given test. This vastly speeds up the entire process.
New test cases should use ZFS_LINUX_TEST_SRC to declare their test
source code and ZFS_LINUX_TEST_RESULT to check the result. All of
the existing kernel-*.m4 files have been updated accordingly, see
config/kernel-current-time.m4 for a basic example. The legacy
ZFS_LINUX_TRY_COMPILE macro has been kept to handle special cases
but it's use is not encouraged.
master (secs) patched (secs)
------------- ----------------
autogen.sh 61 68
configure 137 24 (~17% of current run time)
make -j $(nproc) 44 44
make rpms 287 150
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8547Closes#9132Closes#9341
Conflicts:
Makefile.am
config/kernel-fpu.m4
fxsave and xsave require the target address to be 16-/64-byte aligned.
kmalloc(_node) does not (yet) offer such fine-grained control over
alignment[0,1], even though it does "the right thing" most of the time
for power-of-2 sizes. unfortunately, alignment is completely off when
using certain debugging or hardening features/configs, such as KASAN,
slub_debug=Z or the not-yet-upstream SLAB_CANARY.
Use alloc_pages_node() instead which allows us to allocate page-aligned
memory. Since fpregs_state is padded to a full page anyway, and this
code is only relevant for x86 which has 4k pages, this approach should
not allocate any unnecessary memory but still guarantee the needed
alignment.
0: https://lwn.net/Articles/787740/
1: https://lore.kernel.org/linux-block/20190826111627.7505-1-vbabka@suse.cz/
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9608Closes#9674
Restore the SIMD optimization for 4.19.38 LTS, 4.14.120 LTS,
and 5.0 and newer kernels.
This commit squashes the following commits from master in to
a single commit which can be applied to 0.8.2.
10fa2545 - Linux 4.14, 4.19, 5.0+ compat: SIMD save/restore
b88ca2ac - Enable SIMD for encryption
095b5412 - Fix CONFIG_X86_DEBUG_FPU build failure
e5db3134 - Linux 5.0 compat: SIMD compatibility
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
When the xattr/cleanup.ksh script is unable to remove the test group
due to an active process then it will not call default_cleanup. This
will result in a zvol_ENOSPC/setup failure when attempting to create
the /mnt/testdir directory which will already exist.
Resolve the issue by performing the default_cleanup before removing
the test user and group to ensure this step always happens. Also
allow one more retry to further minimize the likelihood of the
cleanup failing.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9358
Originally the zfs_vdev_elevator module option was added as a
convenience so the requested elevator would be automatically set
on the underlying block devices. At the time this was simple
because the kernel provided an API function which did exactly this.
This API was then removed in the Linux 4.12 kernel which prompted
us to add compatibly code to set the elevator via a usermodehelper.
While well intentioned this introduced a bug which could cause a
system hang, that issue was subsequently fixed by commit 2a0d4188.
In order to avoid future bugs in this area, and to simplify the code,
this functionality is being deprecated. A console warning has been
added to notify any existing consumers and the documentation updated
accordingly. This option will remain for the lifetime of the 0.8.x
series for compatibility but if planned to be phased out of master.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #8664Closes#9317
Trying to 'zfs diff' a snapshot with large dnodes will incorrectly try
to access its interior slots when dnodesize > sizeof(dnode_phys_t).
This is normally not an issue because the interior slots are
zero-filled, which report_dnode() handles calling
report_free_dnode_range(). However this is not the case for encrypted
large dnodes or filesystem using many SA based xattrs where the extra
data past the legacy dnode size boundary is interpreted as a
dnode_phys_t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7678Closes#8931Closes#9343
The difference between the sizes could be positive or negative. Leaving
the types as unsigned means the result overflows when the difference is
negative and removing the labs() means we'll have introduced a bug. The
subtraction results in the correct value when the unsigned integer is
interpreted as a signed integer by labs().
Clang doesn't see that we're doing a subtraction and abusing the types.
It sees the result of the subtraction, an unsigned value, being passed
to an absolute value function and emits a warning which we treat as an
error.
Reviewed by: Youzhong Yang <youzhong@gmail.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9355
Move the trailing newlines from the error message strings to the format
strings to more closely match the other error messages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9330
This commit fixes a NULL pointer dereference triggered in
spa_vdev_remove_top_check() by trying to "zpool remove" an indirect
vdev.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9327
Since 4f342e45 env(1) must be able to find a "python2" executable in
the "constrained path" on systems configured with --with-python=2.x
otherwise the ZFS Test Suite won't be able to use Python scripts.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9325
Currently, spa_keystore_change_key_sync_impl() does not recurse
into clones when updating encryption roots for either a call to
'zfs promote' or 'zfs change-key'. This can cause children of
these clones to end up in a state where they point to the wrong
dataset as the encryption root. It can also trigger ASSERTs in
some cases where the code checks reference counts on wrapping
keys. This patch fixes this issue by ensuring that this function
properly recurses into clones during processing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9267Closes#9294
/usr/bin/env python3 is the suggested[1] shebang for Python in general
(likewise for python2) and is conventional across platforms. This eases
development on systems where python is not installed in /usr/bin
(FreeBSD for example) and makes it possible to develop in virtual
environments (venv) for isolating dependencies.
Many packaging guidelines discourage the use of /usr/bin/env, but since
this is the canonical way of writing shebangs in the Python community,
many packaging scripts are already equipped to handle substituting the
appropriate absolute path to python automatically.
Some RPM package builders lacking brp-mangle-shebangs need a small
fallback mechanism in the package spec to stamp the appropriate shebang
on installed Python scripts.
[1]: https://docs.python.org/3/using/unix.html?#miscellaneous
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9314
Currently, the DSL scan code figures out when it should suspend
processing and allow a txg to continue by calling the function
dsl_scan_check_suspend(). Unfortunately, this function only
allows the scan to suspend at a level 0 block. In the event that
the system is scanning a bunch of empty snapshots or a resilver
is running with a high enough scn_cur_min_txg, the scan will
stop processing each dataset at the root level, deciding it
has nothing left to do. This means that the check_suspend
function is never called and the txg remains stuck until a
dataset is found that has data to scan.
This patch fixes the problem by allowing scans to suspend at
the root level of the objset. For backwards compatibility, we
use the bookmark <objsetid, 0, 0, 0> when we suspend here so
that older versions of the code will work as intended.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9300
filetest_001_pos verifies that various checksum algorithms detect
corruption by overwriting the underlying vdev on which a file resides.
It is possible for the overwrite to miss the blocks of a file, causing a
spurious failure. This change introduces a function to corrupt the
individual blocks of a file as determined by zdb.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9288
Get rid of the `get_used_prop` function. `get_prop used` works fine.
Fix the comment describing the function parameters. The type does not
have a default, and mntp is also used for ext2.
Rename the variable for the number of copies from `copy` to `copies`.
Use a `case` statement to match the type parameter, order the cases
alphabetically, and add a little sanity checking for good measure.
Use eval to make sure the output of commands is silenced rather than
the log messages when redirecting output to /dev/null.
Simplify cases where zfs requires special behavior.
Don't allow the test to loop forever in the event space usage does not
change. Bail out of the loop and fail after an arbitrary number of
iterations.
Add more information to the log message when the test fails, to help
debugging.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9286
Currently, the noop receive code fails to work with raw send streams
and resuming send streams. This happens because zfs_receive_impl()
reads the DRR_BEGIN payload without reading the payload itself.
Normally, the kernel expects to read this itself, but in this case
the recv_skip() code runs instead and it is not prepared to handle
the stream being left at any place other than the beginning of a
record.
This patch resolves this issue by manually reading the DRR_BEGIN
payload in the dry-run case. This patch also includes a number of
small fixups in this code path.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9221Closes#9173
Remove a lot of unnecessary setting and incrementing of `i`.
Remove unused variable `j`.
Instead of calling out to Python in a loop to generate the same string
repeatedly, generate the string once using shell constructs before
entering the loop.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9284
md5sum in particular but also sha256sum to a lesser extent is used
in several areas of the test suite for computing checksums. The vast
majority of invocations are followed by `| awk '{ print $1 }'`.
Introduce functions to wrap up `md5sum $file | awk '{ print $1 }'` and
likewise for sha256sum. These also serve as a convenient interface for
alternative implementations on other platforms.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9280
TRUE and FALSE happen to be defined, but we should use B_TRUE and
B_FALSE for the sake of consistency.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9264
Account for ZFS_MAX_DATASET_NAME_LEN in kstat data size. This value
is ignored in the Linux kstat code but resolves the issue for other
platforms.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9254Closes#9151
Create a larger file to extend the time required to perform the
removal. Occasional failures were observed due to the removal
completing before the cancel could be requested.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9259
When running on larger memory systems, we can overflow the value of
maxinflight. This can result in maxinflight having a value of 0 causing
the system to hang.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#9272
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9251
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9250
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9249
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9247
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9246
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9244
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9243
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9242
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9240
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9237
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9248
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9241
Brian Behlendorf
Richard Yao
Ryan Moeller
loli10K
Igor K
George Melikov
Matthew Macy
Didier Roche
dacianstremtan
Fabian-Gruenbichler
Tom Caputi
John Wren Kennedy
George Wilson
Andrea Gelmini