Correct various typos in the comments and tests.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#10423
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
When we copy the envblock's contents out, we currently treat it as
a normal C string. However, this functionality is supposed to more
closely emulate interacting with a file. As a consequence, we were
incorrectly truncating the contents of the envblock by replacing
the final byte of the buffer with a null character.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10405
C++ is a little picky about not using keywords for names, or string
constness.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10409
Given the following test program:
#include <time.h>
#include <stdio.h>
#include <stdint.h>
int main() {
printf("time_t: %d\n", sizeof(time_t));
printf("long: %d\n", sizeof(long));
printf("long long: %d\n", sizeof(long long));
}
These are output on various x86 architectures:
x32$ time_t: 8
x32$ long: 4
x32$ long long: 8
amd64$ time_t: 8
amd64$ long: 8
amd64$ long long: 8
i386$ time_t: 4
i386$ long: 4
i386$ long long: 8
Therefore code using "%l[du]" to format time_ts produced warnings on x32
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@gmail.com>
Closes#10357Closes#844
When a manual trim is run against an entire pool, errors about
particular devices which don't support trim are suppressed. This changes
zpool_trim() in libzfs so that it doesn't return an error when the only
errors are suppressed ones. An exception is made when none of the
devices support trim, in which case an error is reported and a non-zero
status is returned.
This also fixes how the --wait flag works in the presence of suppressed
errors. In particular, suppressed errors no longer cause zpool_trim()
to skip the wait.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10263Closes#10372
Allow zfs datasets to be mounted on Linux without relying on the
invocation of an external processes. This is the same behavior
which is implemented for FreeBSD.
Use of the libmount library was originally considered because it
provides functionality to properly lock and update the /etc/mtab
file. However, these days /etc/mtab is typically a symlink to
/proc/self/mounts so there's nothing to updated. Therefore, we
call mount(2) directly and avoid any additional dependencies.
If required the legacy behavior can be enabled by setting the
ZFS_MOUNT_HELPER environment variable. This may be needed in
environments where SELinux in enabled and the zfs binary does
not have mount permission.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
#10294
Small program that converts a dataset id and an object id to a path
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10204
Reorganizing ABD code base so OS-independent ABD code has been placed
into a common abd.c file. OS-dependent ABD code has been left in each
OS's ABD source files, and these source files have been renamed to
abd_os.
The OS-independent ABD code is now under:
module/zfs/abd.c
With the OS-dependent code in:
module/os/linux/zfs/abd_os.c
module/os/freebsd/zfs/abd_os.c
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10293
Modern bootloaders leverage data stored in the root filesystem to
enable some of their powerful features. GRUB specifically has a grubenv
file which can store large amounts of configuration data that can be
read and written at boot time and during normal operation. This allows
sysadmins to configure useful features like automated failover after
failed boot attempts. Unfortunately, due to the Copy-on-Write nature
of ZFS, the standard behavior of these tools cannot handle writing to
ZFS files safely at boot time. We need an alternative way to store
data that allows the bootloader to make changes to the data.
This work is very similar to work that was done on Illumos to enable
similar functionality in the FreeBSD bootloader. This patch is different
in that the data being stored is a raw grubenv file; this file can store
arbitrary variables and values, and the scripting provided by grub is
powerful enough that special structures are not required to implement
advanced behavior.
We repurpose the second padding area in each label to store the grubenv
file, protected by an embedded checksum. We add two ioctls to get and
set this data, and libzfs_core and libzfs functions to access them more
easily. There are no direct command line interfaces to these functions;
these will be added directly to the bootloader utilities.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10009
When a top-level vdev is removed from a pool it is converted to an
indirect vdev. Until now splitting such mirrored pools was not possible
with zpool split. This patch enables handling of indirect vdevs and
splitting of those pools with zpool split.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10283
The 'zfs load-key' command was broken for 'keyformat=passphrase'.
Use the correct output vars when stdin is an interactive terminal.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: adam moss <c@yotes.com>
Closes#10264Closes#10265
Every platform has their own preferred methods for implementing URI
schemes beyond the currently supported file scheme (e.g. 'https' on
FreeBSD would likely use libfetch, while Linux distros and illumos
would probably use libcurl, etc). It would be helpful if libzfs can
be extended to support additional schemes in a simple manner.
A table of (scheme, handler_function) pairs is added to libzfs_crypto.c,
and the existing functions in libzfs_crypto.c so that when the key
format is ZFS_KEYFORMAT_URI, the scheme from the URI string is
extracted, and a matching handler it located in the aforementioned
table (returning an error if no matching handler is found). The handler
function is then invoked to retrieve the key material (in the format
specified by the keyformat property) and the key is loaded or the
handler can return an error to abort the key loading process.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#10218
This aids in debugging, so that we can use the same infrastructure to
walk zfs's list_t in the kernel module and in the userland libraries
(e.g. when debugging ztest).
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10236
Deduplicated send streams (i.e. `zfs send -D` and `zfs receive` of such
streams) are deprecated. Deduplicated send streams can be received by
first converting them to non-deduplicated with the `zstream redup`
command.
This commit removes the code for sending and receiving deduplicated send
streams. `zfs send -D` will now print a warning, ignore the `-D` flag,
and generate a regular (non-deduplicated) send stream. `zfs receive` of
a deduplicated send stream will print an error message and fail.
The resulting code simplification (especially in the kernel's support
for receiving dedup streams) should help enable future performance
enhancements.
Several new tests are added which leverage `zstream redup`.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #7887
Issue #10117
Issue #10156Closes#10212
This commit fixes a bunch of missing free() calls in a10d50f99
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: João Carlos Mendes Luís <jonny@jonny.eng.br>
Closes#10219
Musl libc defined `stat64` as a macro, which causes the build to fail
upon compiling os/linux/getmntany.c due to conflicts between the forward
declaration and the implementation.
This commit fixes that by including <sys/stat.h> in "sys/mnttab.h"
directly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Hiếu Lê <leorize+oss@disroot.org>
Closes#10195
Add the FreeBSD platform code to the OpenZFS repository. As of this
commit the source can be compiled and tested on FreeBSD 11 and 12.
Subsequent commits are now required to compile on FreeBSD and Linux.
Additionally, they must pass the ZFS Test Suite on FreeBSD which is
being run by the CI. As of this commit 1230 tests pass on FreeBSD
and there are no unexpected failures.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#898Closes#8987
Deduplicated send and receive is deprecated. To ease migration to the
new dedup-send-less world, the commit adds a `zstream redup` utility to
convert deduplicated send streams to normal streams, so that they can
continue to be received indefinitely.
The new `zstream` command also replaces the functionality of
`zstreamdump`, by way of the `zstream dump` subcommand. The
`zstreamdump` command is replaced by a shell script which invokes
`zstream dump`.
The way that `zstream redup` works under the hood is that as we read the
send stream, we build up a hash table which maps from `<GUID, object,
offset> -> <file_offset>`.
Whenever we see a WRITE record, we add a new entry to the hash table,
which indicates where in the stream file to find the WRITE record for
this block. (The key is `drr_toguid, drr_object, drr_offset`.)
For entries other than WRITE_BYREF, we pass them through unchanged
(except for the running checksum, which is recalculated).
For WRITE_BYREF records, we change them to WRITE records. We find the
referenced WRITE record by looking in the hash table (for the record
with key `drr_refguid, drr_refobject, drr_refoffset`), and then reading
the record header and payload from the specified offset in the stream
file. This is why the stream can not be a pipe. The found WRITE record
replaces the WRITE_BYREF record, with its `drr_toguid`, `drr_object`,
and `drr_offset` fields changed to be the same as the WRITE_BYREF's
(i.e. we are writing the same logical block, but with the data supplied
by the previous WRITE record).
This algorithm requires memory proportional to the number of WRITE
records (same as `zfs send -D`), but the size per WRITE record is
relatively low (40 bytes, vs. 72 for `zfs send -D`). A 1TB send stream
with 8KB blocks (`recordsize=8k`) would use around 5GB of RAM to
"redup".
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10124Closes#10156
This commit makes the L2ARC persistent across reboots. We implement
a light-weight persistent L2ARC metadata structure that allows L2ARC
contents to be recovered after a reboot. This significantly eases the
impact a reboot has on read performance on systems with large caches.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Saso Kiselkov <skiselkov@gmail.com>
Co-authored-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Ported-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#925Closes#1823Closes#2672Closes#3744Closes#9582
Commit 379ca9c removed the check on aux devices to be block devices also
changing zfs_ioctl(hdl, ZFS_IOC_VDEV_ADD, ...) and
zfs_ioctl(hdl, ZFS_IOC_POOL_CREATE, ...) to never set ENOTBLK. This
change removes the dangling check for ENOTBLK that will never trigger.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alex John <alex@stty.io>
Closes#10173
Add a mechanism to wait for delete queue to drain.
When doing redacted send/recv, many workflows involve deleting files
that contain sensitive data. Because of the way zfs handles file
deletions, snapshots taken quickly after a rm operation can sometimes
still contain the file in question, especially if the file is very
large. This can result in issues for redacted send/recv users who
expect the deleted files to be redacted in the send streams, and not
appear in their clones.
This change duplicates much of the zpool wait related logic into a
zfs wait command, which can be used to wait until the internal
deleteq has been drained. Additional wait activities may be added
in the future.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9707
Make the cityhash code compile into libzfs, in preparation for the new
"zstream" command.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10152
Dedup send can only deduplicate over the set of blocks in the send
command being invoked, and it does not take advantage of the dedup table
to do so. This is a very common misconception among not only users, but
developers, and makes the feature seem more useful than it is. As a
result, many users are using the feature but not getting any benefit
from it.
Dedup send requires a nontrivial expenditure of memory and CPU to
operate, especially if the dataset(s) being sent is (are) not already
using a dedup-strength checksum.
Dedup send adds developer burden. It expands the test matrix when
developing new features, causing bugs in released code, and delaying
development efforts by forcing more testing to be done.
As a result, we are deprecating the use of `zfs send -D` and receiving
of such streams. This change adds a warning to the man page, and also
prints the warning whenever dedup send or receive are used.
In a future release, we plan to:
1. remove the kernel code for generating deduplicated streams
2. make `zfs send -D` generate regular, non-deduplicated streams
3. remove the kernel code for receiving deduplicated streams
4. make `zfs receive` of deduplicated streams process them in userland
to "re-duplicate" them, so that they can still be received.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#7887Closes#10117
libzfs aborts and dumps core on EINVAL from the kernel when trying to
do a redacted send with a bookmark that is not a redaction bookmark.
Move redacted bookmark validation into libzfs.
Check if the bookmark given for redactions is actually a redaction
bookmark. Print an error message and exit gracefully if it is not.
Don't abort on EINVAL in zfs_send_one.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10138
This change adds a separate return code to zfs_ioc_recv that is used
for incomplete streams, in addition to the existing return code for
streams that contain corruption.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10122
Currently when the dataset is in use we can't receive snapshots.
zfs send test/1@asd | zfs recv -FM test/2
cannot unmount '/test/2': Device busy
This commits add option 'M' which attempts to forcibly unmount the
dataset. Thanks to this we can enforce receiving snapshots in a
single step.
Note that this functionality is not supported on Linux because the
VFS will prevent active mounted filesystems from being unmounted,
even with the force option. This is the intended VFS behavior.
Test cases were added to verify the expected behavior based on
the platform.
Discussed-with: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
External-issue: https://reviews.freebsd.org/D22306Closes#9904
UINT64_MAX is not exactly representable as a double.
The closest representation is UINT64_MAX + 1, so we can use a >=
comparison instead of > for the bounds check.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10127
Filesystems allow overlay mounts by default on FreeBSD and Linux.
Respect the native convention by switching the default to overlay=on,
while retaining the option to turn the property off for compatibility
with other operating systems' conventions.
Update documentation and tests accordingly.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10030
Manual trims fall into the category of long-running pool activities
which people might want to wait synchronously for. This change adds
support to 'zpool wait' for waiting for manual trim operations to
complete. It also adds a '-w' flag to 'zpool trim' which can be used to
turn 'zpool trim' into a synchronous operation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10071
__zio_execute() calls zio_taskq_member() to determine if we are running
in a zio interrupt taskq, in which case we may need to switch to
processing this zio in a zio issue taskq. The call to
zio_taskq_member() can become a performance bottleneck when we are
processing a high rate of zio's.
zio_taskq_member() calls taskq_member() on each of the zio interrupt
taskqs, of which there are 21. This is slow because each call to
taskq_member() does tsd_get(taskq_tsd), which on Linux is relatively
slow.
This commit improves the performance of zio_taskq_member() by having it
cache the value of tsd_get(taskq_tsd), reducing the number of those
calls to 1/21th of the current behavior.
In a test case running `zfs send -c >/dev/null` of a filesystem with
small blocks (average 2.5KB/block), zio_taskq_member() was using 6.7% of
one CPU, and with this change it is reduced to 1.3%. Overall time to
perform the `zfs send` reduced by 10% (~150,000 block/sec to ~165,000
blocks/sec).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10070
With the FreeBSD platform changes that were made for #10073
it is no longer necessary on FreeBSD to open the control device
exclusively to get onexit callbacks invoked.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10076
As part of the Linux kernel's y2038 changes the time_t type has been
fully retired. Callers are now required to use the time64_t type.
Rather than move to the new type, I've removed the few remaining
places where a time_t is used in the kernel code. They've been
replaced with a uint64_t which is already how ZFS internally
handled these values.
Going forward we should work towards updating the remaining user
space time_t consumers to the 64-bit interfaces.
Reviewed-by: Matthew Macy <mmacy@freebsd.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10052Closes#10064
This adds support for setting user properties in a
zfs channel program by adding 'zfs.sync.set_prop'
and 'zfs.check.set_prop' to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Contributions-by: Jason King <jason.king@joyent.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9950
Linux uses sysfs to determine the module version, FreeBSD uses a
different method.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9978
This feature allows copying existing bookmarks using
zfs bookmark fs#target fs#newbookmark
There are some niche use cases for such functionality,
e.g. when using bookmarks as markers for replication progress.
Copying redaction bookmarks produces a normal bookmark that
cannot be used for redacted send (we are not duplicating
the redaction object).
ZCP support for bookmarking (both creation and copying) will be
implemented in a separate patch based on this work.
Overview:
- Terminology:
- source = existing snapshot or bookmark
- new/bmark = new bookmark
- Implement bookmark copying in `dsl_bookmark.c`
- create new bookmark node
- copy source's `zbn_phys` to new's `zbn_phys`
- zero-out redaction object id in copy
- Extend existing bookmark ioctl nvlist schema to accept
bookmarks as sources
- => `dsl_bookmark_create_nvl_validate` is authoritative
- use `dsl_dataset_is_before` check for both snapshot
and bookmark sources
- Adjust CLI
- refactor shortname expansion logic in `zfs_do_bookmark`
- Update man pages
- warn about redaction bookmark handling
- Add test cases
- CLI
- pyyzfs libzfs_core bindings
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
Currently SIMD accelerated AES-GCM performance is limited by two
factors:
a. The need to disable preemption and interrupts and save the FPU
state before using it and to do the reverse when done. Due to the
way the code is organized (see (b) below) we have to pay this price
twice for each 16 byte GCM block processed.
b. Most processing is done in C, operating on single GCM blocks.
The use of SIMD instructions is limited to the AES encryption of the
counter block (AES-NI) and the Galois multiplication (PCLMULQDQ).
This leads to the FPU not being fully utilized for crypto
operations.
To solve (a) we do crypto processing in larger chunks while owning
the FPU. An `icp_gcm_avx_chunk_size` module parameter was introduced
to make this chunk size tweakable. It defaults to 32 KiB. This step
alone roughly doubles performance. (b) is tackled by porting and
using the highly optimized openssl AES-GCM assembler routines, which
do all the processing (CTR, AES, GMULT) in a single routine. Both
steps together result in up to 32x reduction of the time spend in
the en/decryption routines, leading up to approximately 12x
throughput increase for large (128 KiB) blocks.
Lastly, this commit changes the default encryption algorithm from
AES-CCM to AES-GCM when setting the `encryption=on` property.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Jason King <jason.king@joyent.com>
Reviewed-By: Tom Caputi <tcaputi@datto.com>
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#9749
-fno-common is the new default in GCC 10, replacing -fcommon in
GCC <= 9, so static data must only be allocated once.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9943
When we finish a zfs receive, dmu_recv_end_sync() calls
zvol_create_minors(async=TRUE). This kicks off some other threads that
create the minor device nodes (in /dev/zvol/poolname/...). These async
threads call zvol_prefetch_minors_impl() and zvol_create_minor(), which
both call dmu_objset_own(), which puts a "long hold" on the dataset.
Since the zvol minor node creation is asynchronous, this can happen
after the `ZFS_IOC_RECV[_NEW]` ioctl and `zfs receive` process have
completed.
After the first receive ioctl has completed, userland may attempt to do
another receive into the same dataset (e.g. the next incremental
stream). This second receive and the asynchronous minor node creation
can interfere with one another in several different ways, because they
both require exclusive access to the dataset:
1. When the second receive is finishing up, dmu_recv_end_check() does
dsl_dataset_handoff_check(), which can fail with EBUSY if the async
minor node creation already has a "long hold" on this dataset. This
causes the 2nd receive to fail.
2. The async udev rule can fail if zvol_id and/or systemd-udevd try to
open the device while the the second receive's async attempt at minor
node creation owns the dataset (via zvol_prefetch_minors_impl). This
causes the minor node (/dev/zd*) to exist, but the udev-generated
/dev/zvol/... to not exist.
3. The async minor node creation can silently fail with EBUSY if the
first receive's zvol_create_minor() trys to own the dataset while the
second receive's zvol_prefetch_minors_impl already owns the dataset.
To address these problems, this change synchronously creates the minor
node. To avoid the lock ordering problems that the asynchrony was
introduced to fix (see #3681), we create the minor nodes from open
context, with no locks held, rather than from syncing contex as was
originally done.
Implementation notes:
We generally do not need to traverse children or prefetch anything (e.g.
when running the recv, snapshot, create, or clone subcommands of zfs).
We only need recursion when importing/opening a pool and when loading
encryption keys. The existing recursive, asynchronous, prefetching code
is preserved for use in these cases.
Channel programs may need to create zvol minor nodes, when creating a
snapshot of a zvol with the snapdev property set. We figure out what
snapshots are created when running the LUA program in syncing context.
In this case we need to remember what snapshots were created, and then
try to create their minor nodes from open context, after the LUA code
has completed.
There are additional zvol use cases that asynchronously own the dataset,
which can cause similar problems. E.g. changing the volmode or snapdev
properties. These are less problematic because they are not recursive
and don't touch datasets that are not involved in the operation, there
is still potential for interference with subsequent operations. In the
future, these cases should be similarly converted to create the zvol
minor node synchronously from open context.
The async tasks of removing and renaming minors do not own the objset,
so they do not have this problem. However, it may make sense to also
convert these operations to happen synchronously from open context, in
the future.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-65948
Closes#7863Closes#9885
Implements the RAID-Z function using AltiVec SIMD.
This is basically the NEON code translated to AltiVec.
Note that the 'fletcher' algorithm requires 64-bits
operations, and the initial implementations of AltiVec
(PPC74xx a.k.a. G4, PPC970 a.k.a. G5) only has up to
32-bits operations, so no 'fletcher'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9539
FreeBSD doesn't have a mount flag for determining the
disposition of xattr. Disable so that it is fetched
by the default route so that 'zfs get xattr' returns
the correct value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9862
With recent SPL changes there is no longer any need for a per
platform version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9860
Over the years several slightly different approaches were used
in the Makefiles to determine the target architecture. This
change updates both the build system and Makefile to handle
this in a consistent fashion.
TARGET_CPU is set to i386, x86_64, powerpc, aarch6 or sparc64
and made available in the Makefiles to be used as appropriate.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9848
zfs_mount_at() mounts a dataset at an arbitrary mountpoint rather than
at the configured mountpoint. This may be used by consumers that wish to
temporarily expose a dataset at another mountpoint without altering
dataset/pool properties.
This will be used by FreeBSD's libbe be_mount(), which mounts a boot
environment at an arbitrary mountpoint.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#9833
Update the project website links contained in to repository to
reference the secure https://zfsonlinux.org address.
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9837
This commit adds the --saved (-S) to the 'zfs send' command.
This flag allows a user to send a partially received dataset,
which can be useful when migrating a backup server to new
hardware. This flag is compatible with resumable receives, so
even if the saved send is interrupted, it can be resumed.
The flag does not require any user / kernel ABI changes or any
new feature flags in the send stream format.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Reviewed-by: Christian Schwarz <me@cschwarz.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9007
Rather than defining a new instance of 'aok' in every compilation
unit which includes this header, there is a single instance
defined in zone.c, and the header now only declares an extern.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Closes#9752
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
Resolve the reported memory leak by using a dedicated local vptr
variable to store the pointer reported by calloc(). Only assign the
passed **vtoc function argument on success, in all other cases vptr
is freed.
[lib/libefi/rdwr_efi.c:403]: (error) Memory leak: vtoc
[lib/libefi/rdwr_efi.c:422]: (error) Memory leak: vtoc
[lib/libefi/rdwr_efi.c:440]: (error) Memory leak: vtoc
[lib/libefi/rdwr_efi.c:454]: (error) Memory leak: vtoc
[lib/libefi/rdwr_efi.c:470]: (error) Memory leak: vtoc
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
Add the 'zfs jail/unjail' subcommands along with the relevant
documentation from FreeBSD. This feature is not supported on
Linux and still requires the match kernel ioctls which will
be included when the FreeBSD platform code is integrated.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9686
Remove the ASSERTV macro and handle suppressing unused
compiler warnings for variables only in ASSERTs using the
__attribute__((unused)) compiler annotation. The annotation
is understood by both gcc and clang.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9671
- on Linux move Linux specific headers to zfs_context_os.h
- on FreeBSD move FreeBSD specific definitions to zfs_context_os.h
- remove duplicate tsd_ definitions
- remove unused AT_TYPE
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9668
There may be circumstances where it's desirable that all blocks
in a specified dataset be stored on the special device. Relax
the artificial 128K limit and allow the special_small_blocks
property to be set up to 1M. When blocks >1MB have been enabled
via the zfs_max_recordsize module option, this limit is increased
accordingly.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9131Closes#9355
Include the required headers for FreeBSD.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9634
fallocate(2) is a Linux-specific system call which in unavailable
on other platforms.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9633
The command line switch -A (ignore ASSERTs) has always been available
in zdb but was never connected up to the correct global variable.
There are times when you need zdb to ignore asserts and keep dumping
out whatever information it can get despite the ASSERT(s) failing.
It was always intended to be part of zdb but was incomplete.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9610
Provide a common zfs_file_* interface which can be implemented on all
platforms to perform normal file access from either the kernel module
or the libzpool library.
This allows all non-portable vnode_t usage in the common code to be
replaced by the new portable zfs_file_t. The associated vnode and
kobj compatibility functions, types, and macros have been removed
from the SPL. Moving forward, vnodes should only be used in platform
specific code when provided by the native operating system.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9556
Removes an incorrect error message from libzfs that suggests applying
'-r' when a zfs subcommand is called with a filesystem path while
expecting either a snapshot or bookmark path.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#9574
When `zpool create -o <property>` is run without root permissions
and the pool property requested is not specifically enumerated in
zpool_valid_proplist(). Then an incorrect error message referring
to an invalid property is printed rather than the expected permission
denied error.
Specifying a pool property at create time should be handled the same
way as filesystem properties in zfs_valid_proplist(). There should
not be default zfs_error_aux() set for properties which are not
listed.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9550Closes#9568
FreeBSD needs a wrapper for handling zfs_cmd ioctls.
In libzfs this is handled by zfs_ioctl. However, here
we need to wrap the call directly.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9511
On Linux the full path preceding devices is stripped when formatting
vdev names. On FreeBSD we only want to strip "/dev/". Hide the
implementation details of path stripping behind zfs_strip_path().
Make zfs_strip_partition_path() static in Linux implementation while
here, since it is never used outside of the file it is defined in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9565
This adds basic support for RISC-V, specifically RV64G.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9540
This change modifies some of the infrastructure for enabling the use of
the DTRACE_PROBE* macros, such that we can use tehm in the "spl" module.
Currently, when the DTRACE_PROBE* macros are used, they get expanded to
create new functions, and these dynamically generated functions become
part of the "zfs" module.
Since the "spl" module does not depend on the "zfs" module, the use of
DTRACE_PROBE* in the "spl" module would result in undefined symbols
being used in the "spl" module. Specifically, DTRACE_PROBE* would turn
into a function call, and the function being called would be a symbol
only contained in the "zfs" module; which results in a linker and/or
runtime error.
Thus, this change adds the necessary logic to the "spl" module, to
mirror the tracing functionality available to the "zfs" module. After
this change, we'll have a "trace_zfs.h" header file which defines the
probes available only to the "zfs" module, and a "trace_spl.h" header
file which defines the probes available only to the "spl" module.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#9525
FreeBSD has its own sha routines that the port uses.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9530
FreeBSD has no analog. Buffered block devices were removed a decade
plus ago.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9508
In original implementation, zpool history will read the whole history
before printing anything, causing memory usage goes unbounded. We fix
this by breaking it into read-print iterations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#9516
The sys/signal.h header doesn't exist on FreeBSD, nor is
it needed on Linux.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9510
The malloc.h include is gratuitous and runs in to the following error
on FreeBSD:
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9509
EBADE, EBADR, and ENOANO do not exist on FreeBSD
The libspl errno.h is similarly platform dependent.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9498
It's mostly a noop on ZoL and it conflicts with platforms that
support dtrace. Remove this header to resolve the conflict.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9497
Currently, incremental recursive encrypted receives fail to work
for any snapshot after the first. The reason for this is because
the check in zfs_setup_cmdline_props() did not properly realize
that when the user attempts to use '-x encryption' in this
situation, they are not really overriding the existing encryption
property and instead are attempting to prevent it from changing.
This resulted in an error message stating: "encryption property
'encryption' cannot be set or excluded for raw or incremental
streams".
This problem is fixed by updating the logic to expect this use
case.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9494
Contrary to initial testing we cannot rely on these kernels to
invalidate the per-cpu FPU state and restore the FPU registers.
Nor can we guarantee that the kernel won't modify the FPU state
which we saved in the task struck.
Therefore, the kfpu_begin() and kfpu_end() functions have been
updated to save and restore the FPU state using our own dedicated
per-cpu FPU state variables.
This has the additional advantage of allowing us to use the FPU
again in user threads. So we remove the code which was added to
use task queues to ensure some functions ran in kernel threads.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #9346Closes#9403
Consistently use the `zfs_ioctl()` wrapper since `ioctl()` cannot be
called directly due to differing semantics between platforms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9492
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9493
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9486
Factor Linux specific memory pressure handling out of ARC. Each
platform will have different available interfaces for managing memory
pressure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9472
FreeBSD has its own implementation as do other platforms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9439
While it may sometimes be convenient to export an NFS filesystem with
no_root_squash it should not be the default behavior. Align the
default behavior with the Linux NFS server defaults. To restore
the previous behavior use 'zfs set sharenfs="no_root_squash,..."'.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9397Closes#9425
Since 0.7.0, zpool import would unconditionally block on udev for 30
seconds. This introduced a regression in initramfs environments that
lack udev (particularly mdev based environments), yet use a zfs userland
tools intended for the system that had been built against udev. Gentoo's
genkernel is the main example, although custom user initramfs
environments would be similarly impacted unless special builds of the
ZFS userland utilities were done for them. Such environments already
have their own mechanisms for blocking until device nodes are ready
(such as genkernel's scandelay parameter), so it is unnecessary for
zpool import to block on a non-existent udev until a timeout is reached
inside of them.
Rather than trying to intelligently determine whether udev is available
on the system to avoid unnecessarily blocking in such environments, it
seems best to just allow the environment to override the timeout. I
propose that we add an environment variable called
ZPOOL_IMPORT_UDEV_TIMEOUT_MS. Setting it to 0 would restore the 0.6.x
behavior that was more desirable in mdev based initramfs environments.
This allows the system user land utilities to be reused when building
mdev-based initramfs archives.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#9436
This patch implements a new tree structure for ZFS, and uses it to
store range trees more efficiently.
The new structure is approximately a B-tree, though there are some
small differences from the usual characterizations. The tree has core
nodes and leaf nodes; each contain data elements, which the elements
in the core nodes acting as separators between its children. The
difference between core and leaf nodes is that the core nodes have an
array of children, while leaf nodes don't. Every node in the tree may
be only partially full; in most cases, they are all at least 50% full
(in terms of element count) except for the root node, which can be
less full. Underfull nodes will steal from their neighbors or merge to
remain full enough, while overfull nodes will split in two. The data
elements are contained in tree-controlled buffers; they are copied
into these on insertion, and overwritten on deletion. This means that
the elements are not independently allocated, which reduces overhead,
but also means they can't be shared between trees (and also that
pointers to them are only valid until a side-effectful tree operation
occurs). The overhead varies based on how dense the tree is, but is
usually on the order of about 50% of the element size; the per-node
overheads are very small, and so don't make a significant difference.
The trees can accept arbitrary records; they accept a size and a
comparator to allow them to be used for a variety of purposes.
The new trees replace the AVL trees used in the range trees today.
Currently, the range_seg_t structure contains three 8 byte integers
of payload and two 24 byte avl_tree_node_ts to handle its storage in
both an offset-sorted tree and a size-sorted tree (total size: 64
bytes). In the new model, the range seg structures are usually two 4
byte integers, but a separate one needs to exist for the size-sorted
and offset-sorted tree. Between the raw size, the 50% overhead, and
the double storage, the new btrees are expected to use 8*1.5*2 = 24
bytes per record, or 33.3% as much memory as the AVL trees (this is
for the purposes of storing metaslab range trees; for other purposes,
like scrubs, they use ~50% as much memory).
We reduced the size of the payload in the range segments by teaching
range trees about starting offsets and shifts; since metaslabs have a
fixed starting offset, and they all operate in terms of disk sectors,
we can store the ranges using 4-byte integers as long as the size of
the metaslab divided by the sector size is less than 2^32. For 512-byte
sectors, this is a 2^41 (or 2TB) metaslab, which with the default
settings corresponds to a 256PB disk. 4k sector disks can handle
metaslabs up to 2^46 bytes, or 2^63 byte disks. Since we do not
anticipate disks of this size in the near future, there should be
almost no cases where metaslabs need 64-byte integers to store their
ranges. We do still have the capability to store 64-byte integer ranges
to account for cases where we are storing per-vdev (or per-dnode) trees,
which could reasonably go above the limits discussed. We also do not
store fill information in the compact version of the node, since it
is only used for sorted scrub.
We also optimized the metaslab loading process in various other ways
to offset some inefficiencies in the btree model. While individual
operations (find, insert, remove_from) are faster for the btree than
they are for the avl tree, remove usually requires a find operation,
while in the AVL tree model the element itself suffices. Some clever
changes actually caused an overall speedup in metaslab loading; we use
approximately 40% less cpu to load metaslabs in our tests on Illumos.
Another memory and performance optimization was achieved by changing
what is stored in the size-sorted trees. When a disk is heavily
fragmented, the df algorithm used by default in ZFS will almost always
find a number of small regions in its initial cursor-based search; it
will usually only fall back to the size-sorted tree to find larger
regions. If we increase the size of the cursor-based search slightly,
and don't store segments that are smaller than a tunable size floor
in the size-sorted tree, we can further cut memory usage down to
below 20% of what the AVL trees store. This also results in further
reductions in CPU time spent loading metaslabs.
The 16KiB size floor was chosen because it results in substantial memory
usage reduction while not usually resulting in situations where we can't
find an appropriate chunk with the cursor and are forced to use an
oversized chunk from the size-sorted tree. In addition, even if we do
have to use an oversized chunk from the size-sorted tree, the chunk
would be too small to use for ZIL allocations, so it isn't as big of a
loss as it might otherwise be. And often, more small allocations will
follow the initial one, and the cursor search will now find the
remainder of the chunk we didn't use all of and use it for subsequent
allocations. Practical testing has shown little or no change in
fragmentation as a result of this change.
If the size-sorted tree becomes empty while the offset sorted one still
has entries, it will load all the entries from the offset sorted tree
and disregard the size floor until it is unloaded again. This operation
occurs rarely with the default setting, only on incredibly thoroughly
fragmented pools.
There are some other small changes to zdb to teach it to handle btrees,
but nothing major.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy seb@delphix.com
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9181
Factor Linux specific functionality out of libzfs.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Closes#9377
Factor Linux specific functionality out of libzutil.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9356
Factor Linux specific pieces out of libspl.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9336
Factor Linux specific functions out of the zpool command.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9333
Currently, the recv_fix_encryption_hierarchy() function accepts
'destsnap' as one of its parameters. Originally, this was intended
to be the top-level dataset of a receive (whether or not the
receive was recursive). Unfortunately, this parameter actually is
simply the input that is passed in from the command line. When
the user specifies 'zfs recv -d', this string is actually only the
name of the receiving pool since the rest of the name is derived
from the send stream. This causes the function to fail, leaving
some datasets with an invalid encryption hierarchy.
This patch resolves this problem by passing in the top_zfs variable
instead. In order to make this work, this patch also includes some
changes that ensure the value is always present when we need it.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9273Closes#9309
Move the trailing newlines from the error message strings to the format
strings to more closely match the other error messages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9330
Currently the best way to wait for the completion of a long-running
operation in a pool, like a scrub or device removal, is to poll 'zpool
status' and parse its output, which is neither efficient nor convenient.
This change adds a 'wait' subcommand to the zpool command. When invoked,
'zpool wait' will block until a specified type of background activity
completes. Currently, this subcommand can wait for any of the following:
- Scrubs or resilvers to complete
- Devices to initialized
- Devices to be replaced
- Devices to be removed
- Checkpoints to be discarded
- Background freeing to complete
For example, a scrub that is in progress could be waited for by running
zpool wait -t scrub <pool>
This also adds a -w flag to the attach, checkpoint, initialize, replace,
remove, and scrub subcommands. When used, this flag makes the operations
kicked off by these subcommands synchronous instead of asynchronous.
This functionality is implemented using a new ioctl. The type of
activity to wait for is provided as input to the ioctl, and the ioctl
blocks until all activity of that type has completed. An ioctl was used
over other methods of kernel-userspace communiction primarily for the
sake of portability.
Porting Notes:
This is ported from Delphix OS change DLPX-44432. The following changes
were made while porting:
- Added ZoL-style ioctl input declaration.
- Reorganized error handling in zpool_initialize in libzfs to integrate
better with changes made for TRIM support.
- Fixed check for whether a checkpoint discard is in progress.
Previously it also waited if the pool had a checkpoint, instead of
just if a checkpoint was being discarded.
- Exposed zfs_initialize_chunk_size as a ZoL-style tunable.
- Updated more existing tests to make use of new 'zpool wait'
functionality, tests that don't exist in Delphix OS.
- Used existing ZoL tunable zfs_scan_suspend_progress, together with
zinject, in place of a new tunable zfs_scan_max_blks_per_txg.
- Added support for a non-integral interval argument to zpool wait.
Future work:
ZoL has support for trimming devices, which Delphix OS does not. In the
future, 'zpool wait' could be extended to add the ability to wait for
trim operations to complete.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#9162
Move Linux specific tracing headers and source to platform directories
and update the build system.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9290
Move platform specific Linux source under module/os/linux/
and update the build system accordingly. Additional code
restructuring will follow to make the common code fully
portable.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Closes#9206
Currently, the noop receive code fails to work with raw send streams
and resuming send streams. This happens because zfs_receive_impl()
reads the DRR_BEGIN payload without reading the payload itself.
Normally, the kernel expects to read this itself, but in this case
the recv_skip() code runs instead and it is not prepared to handle
the stream being left at any place other than the beginning of a
record.
This patch resolves this issue by manually reading the DRR_BEGIN
payload in the dry-run case. This patch also includes a number of
small fixups in this code path.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9221Closes#9173
Move platform specific Linux headers under include/os/linux/.
Update the build system accordingly to detect the platform.
This lays some of the initial groundwork to supporting building
for other platforms.
As part of this change it was necessary to create both a user
and kernel space sys/simd.h header which can be included in
either context. No functional change, the source has been
refactored and the relevant #include's updated.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Matthew Macy <mmacy@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9198
This fixes a hole in the situation where the resume state is left from
receiving a new dataset and, so, the state is set on the dataset itself
(as opposed to %recv child).
Additionally, distinguish incremental and resume streams in error
messages.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#9252
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9237
This is a typical case of use after free. We would call zfs_close(zhp)
which would free the handle, and then call zfs_iter_children() on that
handle later. This change ensures that the zfs_handle is only closed
when we are ready to return.
Running `zfs inherit -r sharenfs pool` was failing with an error
code without any error messages. After some debugging I've pinpointed
the issue to be memory corruption, which would cause zfs to try to
issue an ioctl to the wrong device and receive ENOTTY.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Issue #7967Closes#9165
When running on an ESXi based VM, I've found that "zpool online -e" will
not expand the zpool, if the disk was expanded in ESXi while the VM was
powered off.
For example, take the following scenario:
1. VM running on top of VMware ESXi
2. ZFS pool created with a given device "sda" of size 8GB
3. VM powered off
4. Device "sda" size expanded to 16GB
5. VM powered on
6. "zpool online -e" used on device "sda"
In this situation, after (2) the zpool will be roughly 8GB in size.
After (6), the expectation is the zpool's size will expand to roughly
16GB in size; i.e. expand to the new size of the "sda" device.
Unfortunately, I've seen that after (6), the zpool size does not change.
What's happening is after (5), the EFI label of the "sda" device will be
such that fields "efi_last_u_lba", "efi_last_lba", and "efi_altern_lba"
all reflect the new size of the disk; i.e. "33554398", "33554431", and
"33554431" respectively.
Thus, the check that we perform in "efi_use_whole_disk":
if ((efi_label->efi_altern_lba == 1) || (efi_label->efi_altern_lba
>= efi_label->efi_last_lba)) {
This will return true, and then we return from the function without
having expanded the size of the zpool/device.
In contrast, if we remove steps (3) and (5) in the sequence above, i.e.
the device is expanded while the VM is powered on, things change. In
that case, the fields "efi_last_u_lba" and "efi_altern_lba" do not
change (i.e. they still reflect the old 8GB device size), but the
"efi_last_lba" field does change (i.e. it now reflects the new 16GB
device size). Thus, when we evaluate the same conditional in
"efi_use_whole_disk", it'll return false, so the zpool is expanded.
Taking all of this into account, this PR updates "efi_use_whole_disk" to
properly expand the zpool when the underlying disk is expanded while the
VM is powered off.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#9111
When creating hundreds of clones (for example using containers with
LXD) cloning slows down as the number of clones increases over time.
The reason for this is that the fetching of the clone information
using a small zcmd buffer requires two ioctl calls, one to determine
the size and a second to return the data. However, this requires
gathering the data twice, once to determine the size and again to
populate the zcmd buffer to return it to userspace.
These are expensive ioctl() calls, so instead, make the default buffer
size much larger: 256K.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#9084
In the past we've seen multiple race conditions that have
to do with open-context threads async threads and concurrent
calls to spa_export()/spa_destroy() (including the one
referenced in issue #9015).
This patch ensures that only one thread can execute the
main body of spa_export_common() at a time, with subsequent
threads returning with a new error code created just for
this situation, eliminating this way any race condition
bugs introduced by concurrent calls to this function.
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#9015Closes#9044
= Motivation
At Delphix we've seen a lot of customer systems where fragmentation
is over 75% and random writes take a performance hit because a lot
of time is spend on I/Os that update on-disk space accounting metadata.
Specifically, we seen cases where 20% to 40% of sync time is spend
after sync pass 1 and ~30% of the I/Os on the system is spent updating
spacemaps.
The problem is that these pools have existed long enough that we've
touched almost every metaslab at least once, and random writes
scatter frees across all metaslabs every TXG, thus appending to
their spacemaps and resulting in many I/Os. To give an example,
assuming that every VDEV has 200 metaslabs and our writes fit within
a single spacemap block (generally 4K) we have 200 I/Os. Then if we
assume 2 levels of indirection, we need 400 additional I/Os and
since we are talking about metadata for which we keep 2 extra copies
for redundancy we need to triple that number, leading to a total of
1800 I/Os per VDEV every TXG.
We could try and decrease the number of metaslabs so we have less
I/Os per TXG but then each metaslab would cover a wider range on
disk and thus would take more time to be loaded in memory from disk.
In addition, after it's loaded, it's range tree would consume more
memory.
Another idea would be to just increase the spacemap block size
which would allow us to fit more entries within an I/O block
resulting in fewer I/Os per metaslab and a speedup in loading time.
The problem is still that we don't deal with the number of I/Os
going up as the number of metaslabs is increasing and the fact
is that we generally write a lot to a few metaslabs and a little
to the rest of them. Thus, just increasing the block size would
actually waste bandwidth because we won't be utilizing our bigger
block size.
= About this patch
This patch introduces the Log Spacemap project which provides the
solution to the above problem while taking into account all the
aforementioned tradeoffs. The details on how it achieves that can
be found in the references sections below and in the code (see
Big Theory Statement in spa_log_spacemap.c).
Even though the change is fairly constraint within the metaslab
and lower-level SPA codepaths, there is a side-change that is
user-facing. The change is that VDEV IDs from VDEV holes will no
longer be reused. To give some background and reasoning for this,
when a log device is removed and its VDEV structure was replaced
with a hole (or was compacted; if at the end of the vdev array),
its vdev_id could be reused by devices added after that. Now
with the pool-wide space maps recording the vdev ID, this behavior
can cause problems (e.g. is this entry referring to a segment in
the new vdev or the removed log?). Thus, to simplify things the
ID reuse behavior is gone and now vdev IDs for top-level vdevs
are truly unique within a pool.
= Testing
The illumos implementation of this feature has been used internally
for a year and has been in production for ~6 months. For this patch
specifically there don't seem to be any regressions introduced to
ZTS and I have been running zloop for a week without any related
problems.
= Performance Analysis (Linux Specific)
All performance results and analysis for illumos can be found in
the links of the references. Redoing the same experiments in Linux
gave similar results. Below are the specifics of the Linux run.
After the pool reached stable state the percentage of the time
spent in pass 1 per TXG was 64% on average for the stock bits
while the log spacemap bits stayed at 95% during the experiment
(graph: sdimitro.github.io/img/linux-lsm/PercOfSyncInPassOne.png).
Sync times per TXG were 37.6 seconds on average for the stock
bits and 22.7 seconds for the log spacemap bits (related graph:
sdimitro.github.io/img/linux-lsm/SyncTimePerTXG.png). As a result
the log spacemap bits were able to push more TXGs, which is also
the reason why all graphs quantified per TXG have more entries for
the log spacemap bits.
Another interesting aspect in terms of txg syncs is that the stock
bits had 22% of their TXGs reach sync pass 7, 55% reach sync pass 8,
and 20% reach 9. The log space map bits reached sync pass 4 in 79%
of their TXGs, sync pass 7 in 19%, and sync pass 8 at 1%. This
emphasizes the fact that not only we spend less time on metadata
but we also iterate less times to convergence in spa_sync() dirtying
objects.
[related graphs:
stock- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGStock.png
lsm- sdimitro.github.io/img/linux-lsm/NumberOfPassesPerTXGLSM.png]
Finally, the improvement in IOPs that the userland gains from the
change is approximately 40%. There is a consistent win in IOPS as
you can see from the graphs below but the absolute amount of
improvement that the log spacemap gives varies within each minute
interval.
sdimitro.github.io/img/linux-lsm/StockVsLog3Days.png
sdimitro.github.io/img/linux-lsm/StockVsLog10Hours.png
= Porting to Other Platforms
For people that want to port this commit to other platforms below
is a list of ZoL commits that this patch depends on:
Make zdb results for checkpoint tests consistent
db587941c5
Update vdev_is_spacemap_addressable() for new spacemap encoding
419ba59145
Simplify spa_sync by breaking it up to smaller functions
8dc2197b7b
Factor metaslab_load_wait() in metaslab_load()
b194fab0fb
Rename range_tree_verify to range_tree_verify_not_present
df72b8bebe
Change target size of metaslabs from 256GB to 16GB
c853f382db
zdb -L should skip leak detection altogether
21e7cf5da8
vs_alloc can underflow in L2ARC vdevs
7558997d2f
Simplify log vdev removal code
6c926f426a
Get rid of space_map_update() for ms_synced_length
425d3237ee
Introduce auxiliary metaslab histograms
928e8ad47d
Error path in metaslab_load_impl() forgets to drop ms_sync_lock
8eef997679
= References
Background, Motivation, and Internals of the Feature
- OpenZFS 2017 Presentation:
youtu.be/jj2IxRkl5bQ
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemaps-project
Flushing Algorithm Internals & Performance Results
(Illumos Specific)
- Blogpost:
sdimitro.github.io/post/zfs-lsm-flushing/
- OpenZFS 2018 Presentation:
youtu.be/x6D2dHRjkxw
- Slides:
slideshare.net/SerapheimNikolaosDim/zfs-log-spacemap-flushing-algorithm
Upstream Delphix Issues:
DLPX-51539, DLPX-59659, DLPX-57783, DLPX-61438, DLPX-41227, DLPX-59320
DLPX-63385
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8442
Strategy of parallel mount is as follows.
1) Initial thread dispatching is to select sets of mount points that
don't have dependencies on other sets, hence threads can/should run
lock-less and shouldn't race with other threads for other sets. Each
thread dispatched corresponds to top level directory which may or may
not have datasets to be mounted on sub directories.
2) Subsequent recursive thread dispatching for each thread from 1)
is to mount datasets for each set of mount points. The mount points
within each set have dependencies (i.e. child directories), so child
directories are processed only after parent directory completes.
The problem is that the initial thread dispatching in
zfs_foreach_mountpoint() can be multi-threaded when it needs to be
single-threaded, and this puts threads under race condition. This race
appeared as mount/unmount issues on ZoL for ZoL having different
timing regarding mount(2) execution due to fork(2)/exec(2) of mount(8).
`zfs unmount -a` which expects proper mount order can't unmount if the
mounts were reordered by the race condition.
There are currently two known patterns of input list `handles` in
`zfs_foreach_mountpoint(..,handles,..)` which cause the race condition.
1) #8833 case where input is `/a /a /a/b` after sorting.
The problem is that libzfs_path_contains() can't correctly handle an
input list with two same top level directories.
There is a race between two POSIX threads A and B,
* ThreadA for "/a" for test1 and "/a/b"
* ThreadB for "/a" for test0/a
and in case of #8833, ThreadA won the race. Two threads were created
because "/a" wasn't considered as `"/a" contains "/a"`.
2) #8450 case where input is `/ /var/data /var/data/test` after sorting.
The problem is that libzfs_path_contains() can't correctly handle an
input list containing "/".
There is a race between two POSIX threads A and B,
* ThreadA for "/" and "/var/data/test"
* ThreadB for "/var/data"
and in case of #8450, ThreadA won the race. Two threads were created
because "/var/data" wasn't considered as `"/" contains "/var/data"`.
In other words, if there is (at least one) "/" in the input list,
the initial thread dispatching must be single-threaded since every
directory is a child of "/", meaning they all directly or indirectly
depend on "/".
In both cases, the first non_descendant_idx() call fails to correctly
determine "path1-contains-path2", and as a result the initial thread
dispatching creates another thread when it needs to be single-threaded.
Fix a conditional in libzfs_path_contains() to consider above two.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8450Closes#8833Closes#8878
Due to some changes introduced in 30af21b 'zfs send' can crash when
provided with invalid inputs: this change attempts to add more checks
to the affected code paths.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9001
When a volume is created in a pool with raidz vdevs and
volblocksize != 128k, the volume can reference more space than is
reserved with the automatically calculated refreservation. There
are two deficiencies in vol_volsize_to_reservation that contribute
to this:
1) Skip blocks may be added to keep each allocation a multiple
of parity + 1. This is the dominating factor when volblocksize
is close to 2^ashift.
2) raidz deflation for 128 KB blocks is different for most other
block sizes.
See "The theory of raidz space accounting" comment in
libzfs_dataset.c for a full explanation.
Authored by: Mike Gerdts <mike.gerdts@joyent.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Sanjay Nadkarni <sanjay.nadkarni@nexenta.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Kody Kantor <kody.kantor@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Mike Gerdts <mike.gerdts@joyent.com>
Porting Notes:
* ZTS: wait for zvols to exist before writing
* ZTS: use log_must_busy with {zpool|zfs} destroy
OpenZFS-issue: https://www.illumos.org/issues/9318
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/b73ccab0Closes#8973
This small patch fixes the EINVAL case for zfs_receive_one(). A
missing 'else' has been added to the two possible cases, which
will ensure the intended error message is printed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8977
This patch adds the ability for the user to unload keys for
datasets as they are being unmounted. This is analogous to
'zfs mount -l'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes: #8917Closes: #8952
The "zfs remap" command was disabled by
6e91a72fe3, because it has little utility
and introduced some tricky bugs. This commit removes the code for it,
the associated ZFS_IOC_REMAP ioctl, and tests.
Note that the ioctl and property will remain, but have no functionality.
This allows older software to fail gracefully if it attempts to use
these, and avoids a backwards incompatibility that would be introduced if
we renumbered the later ioctls/props.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8944
This patch corrects the error message reported when attempting
to promote a dataset outside of its encryption root.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8905Closes#8935
Problem Statement
=================
ZFS Channel program scripts currently require a timeout, so that hung or
long-running scripts return a timeout error instead of causing ZFS to get
wedged. This limit can currently be set up to 100 million Lua instructions.
Even with a limit in place, it would be desirable to have a sys admin
(support engineer) be able to cancel a script that is taking a long time.
Proposed Solution
=================
Make it possible to abort a channel program by sending an interrupt signal.In
the underlying txg_wait_sync function, switch the cv_wait to a cv_wait_sig to
catch the signal. Once a signal is encountered, the dsl_sync_task function can
install a Lua hook that will get called before the Lua interpreter executes a
new line of code. The dsl_sync_task can resume with a standard txg_wait_sync
call and wait for the txg to complete. Meanwhile, the hook will abort the
script and indicate that the channel program was canceled. The kernel returns
a EINTR to indicate that the channel program run was canceled.
Porting notes: Added missing return value from cv_wait_sig()
Authored by: Don Brady <don.brady@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/9425
OpenZFS-commit: https://github.com/illumos/illumos-gate/commit/d0cb1fb926Closes#8904
Functions such as `fnvlist_lookup_nvlist` need libnvpair to be linked.
Default pkg-config file did not contain it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Harry Mallon <hjmallon@gmail.com>
Closes#8919
When encryption was first added to ZFS, we made a decision to
prevent users from creating unencrypted children of encrypted
datasets. The idea was to prevent users from inadvertently
leaving some of their data unencrypted. However, since the
release of 0.8.0, some legitimate reasons have been brought up
for this behavior to be allowed. This patch simply removes this
limitation from all code paths that had checks for it and updates
the tests accordingly.
Reviewed-by: Jason King <jason.king@joyent.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8737Closes#8870
If dedup is in use, the `dedupditto` property can be set, causing ZFS to
keep an extra copy of data that is referenced many times (>100x). The
idea was that this data is more important than other data and thus we
want to be really sure that it is not lost if the disk experiences a
small amount of random corruption.
ZFS (and system administrators) rely on the pool-level redundancy to
protect their data (e.g. mirroring or RAIDZ). Since the user/sysadmin
doesn't have control over what data will be offered extra redundancy by
dedupditto, this extra redundancy is not very useful. The bulk of the
data is still vulnerable to loss based on the pool-level redundancy.
For example, if particle strikes corrupt 0.1% of blocks, you will either
be saved by mirror/raidz, or you will be sad. This is true even if
dedupditto saved another 0.01% of blocks from being corrupted.
Therefore, the dedupditto functionality is rarely enabled (i.e. the
property is rarely set), and it fulfills its promise of increased
redundancy even more rarely.
Additionally, this feature does not work as advertised (on existing
releases), because scrub/resilver did not repair the extra (dedupditto)
copy (see https://github.com/zfsonlinux/zfs/pull/8270).
In summary, this seldom-used feature doesn't work, and even if it did it
wouldn't provide useful data protection. It has a non-trivial
maintenance burden (again see https://github.com/zfsonlinux/zfs/pull/8270).
We should remove the dedupditto functionality. For backwards
compatibility with the existing CLI, "zpool set dedupditto" will still
"succeed" (exit code zero), but won't have any effect. For backwards
compatibility with existing pools that had dedupditto enabled at some
point, the code will still be able to understand dedupditto blocks and
free them when appropriate. However, ZFS won't write any new dedupditto
blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Issue #8270Closes#8310
The rest of the code/comments use ZFS_DEV, so sync with that.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8912
Redacted send/receive allows users to send subsets of their data to
a target system. One possible use case for this feature is to not
transmit sensitive information to a data warehousing, test/dev, or
analytics environment. Another is to save space by not replicating
unimportant data within a given dataset, for example in backup tools
like zrepl.
Redacted send/receive is a three-stage process. First, a clone (or
clones) is made of the snapshot to be sent to the target. In this
clone (or clones), all unnecessary or unwanted data is removed or
modified. This clone is then snapshotted to create the "redaction
snapshot" (or snapshots). Second, the new zfs redact command is used
to create a redaction bookmark. The redaction bookmark stores the
list of blocks in a snapshot that were modified by the redaction
snapshot(s). Finally, the redaction bookmark is passed as a parameter
to zfs send. When sending to the snapshot that was redacted, the
redaction bookmark is used to filter out blocks that contain sensitive
or unwanted information, and those blocks are not included in the send
stream. When sending from the redaction bookmark, the blocks it
contains are considered as candidate blocks in addition to those
blocks in the destination snapshot that were modified since the
creation_txg of the redaction bookmark. This step is necessary to
allow the target to rehydrate data in the case where some blocks are
accidentally or unnecessarily modified in the redaction snapshot.
The changes to bookmarks to enable fast space estimation involve
adding deadlists to bookmarks. There is also logic to manage the
life cycles of these deadlists.
The new size estimation process operates in cases where previously
an accurate estimate could not be provided. In those cases, a send
is performed where no data blocks are read, reducing the runtime
significantly and providing a byte-accurate size estimate.
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Pavel Zhakarov <pavel.zakharov@delphix.com>
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7958
This change restricts filesystem creation if the given name
contains either '.' or '..'
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: TulsiJain <tulsi.jain@delphix.com>
Closes#8842Closes#8564
For recursive renaming, simplify the code by moving `zhrp` and
`parentname` to inner scope. `zhrp` is only used to test existence
of a parent dataset for recursive dataset dir scan since ba6a24026c.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#8815
The objsetid property, while being stored as a number, is a dataset
identifier and should not be pretty-printed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8784
In compare(), all error cases set the error code to EPIPE, so when an
error is set, the correct assertion to make is that the error is EPIPE,
not EINVAL.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@freqlabs.com>
Closes#8743
When receiving a DRR_OBJECT record the receive_object() function
needs to determine how to handle a spill block associated with the
object. It may need to be removed or kept depending on how the
object was modified at the source.
This determination is currently accomplished using a heuristic which
takes in to account the DRR_OBJECT record and the existing object
properties. This is a problem because there isn't quite enough
information available to do the right thing under all circumstances.
For example, when only the block size changes the spill block is
removed when it should be kept.
What's needed to resolve this is an additional flag in the DRR_OBJECT
which indicates if the object being received references a spill block.
The DRR_OBJECT_SPILL flag was added for this purpose. When set then
the object references a spill block and it must be kept. Either
it is update to date, or it will be replaced by a subsequent DRR_SPILL
record. Conversely, if the object being received doesn't reference
a spill block then any existing spill block should always be removed.
Since previous versions of ZFS do not understand this new flag
additional DRR_SPILL records will be inserted in to the stream.
This has the advantage of being fully backward compatible. Existing
ZFS systems receiving this stream will recreate the spill block if
it was incorrectly removed. Updated ZFS versions will correctly
ignore the additional spill blocks which can be identified by
checking for the DRR_SPILL_UNMODIFIED flag.
The small downside to this approach is that is may increase the size
of the stream and of the received snapshot on previous versions of
ZFS. Additionally, when receiving streams generated by previous
unpatched versions of ZFS spill blocks may still be lost.
OpenZFS-issue: https://www.illumos.org/issues/9952
FreeBSD-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=233277
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8668
The 'zpool resilver' command requires that the resilver_defer
feature is active on the pool. Unfortunately, the check for
this was left out of the original patch. This commit simply
corrects this so that the command properly returns an error
in this case.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8700
The size argument of snprintf(3) in glibc and snprintf() in Linux
kernel includes trailing \0, as snprintf(3) man page explains it as
"write at most size bytes (including the trailing null byte ('\0'))",
i.e. snprintf() can just take buffer size.
e.g. For snprintf() in module/zfs/zfs_ctldir.c, a buffer size is
MAXPATHLEN, and a caller is passing MAXPATHLEN to snprintf(), so size
should just be `path_len` to do what the caller is trying to do.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8692
Add the 'zfs version' and 'zpool version' subcommands to display
the version of the user space utilities and loaded zfs kernel
module. For example:
$ zfs version
zfs-0.8.0-rc3_169_g67e0366b88
zfs-kmod-0.8.0-rc3_169_g67e0366b88
The '-V' and '--version' aliases were added to support the
common convention of using 'zfs --version` to obtain the version
information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: TerraTech <1118433+TerraTech@users.noreply.github.com>
Closes#2501Closes#8567
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#8563Closes#8622
POSIX doesn't define pthread_t as uint_t. It could be a pointer.
This code causes below compile error on a platform using pointer
for pthread_t.
--
kernel.c:815:25: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(void) printf("%u ", (uint_t)pthread_self());
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8558
The length used for the strlcpy() used the size of zv_value
when it should have used the size of zc_name. Correct this
typo.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8595Closes#8596
There are several places where we use zfs_dbgmsg and %p to
print pointers. In the Linux kernel, these values obfuscated
to prevent information leaks which means the pointers aren't
very useful for debugging crash dumps. We decided to restrict
the permissions of dbgmsg (and some other kstats while we were
at it) and print pointers with %px in zfs_dbgmsg as well as
spl_dumpstack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
Closes#8467Closes#8476
Simply appends zhp->zfs_name to the "TIME SENT SNAPSHOT" output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: TerraTech <TerraTech@users.noreply.github.com>
Closes#8543
UNMAP/TRIM support is a frequently-requested feature to help
prevent performance from degrading on SSDs and on various other
SAN-like storage back-ends. By issuing UNMAP/TRIM commands for
sectors which are no longer allocated the underlying device can
often more efficiently manage itself.
This TRIM implementation is modeled on the `zpool initialize`
feature which writes a pattern to all unallocated space in the
pool. The new `zpool trim` command uses the same vdev_xlate()
code to calculate what sectors are unallocated, the same per-
vdev TRIM thread model and locking, and the same basic CLI for
a consistent user experience. The core difference is that
instead of writing a pattern it will issue UNMAP/TRIM commands
for those extents.
The zio pipeline was updated to accommodate this by adding a new
ZIO_TYPE_TRIM type and associated spa taskq. This new type makes
is straight forward to add the platform specific TRIM/UNMAP calls
to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are
handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs.
This makes it possible to largely avoid changing the pipieline,
one exception is that TRIM zio's may exceed the 16M block size
limit since they contain no data.
In addition to the manual `zpool trim` command, a background
automatic TRIM was added and is controlled by the 'autotrim'
property. It relies on the exact same infrastructure as the
manual TRIM. However, instead of relying on the extents in a
metaslab's ms_allocatable range tree, a ms_trim tree is kept
per metaslab. When 'autotrim=on', ranges added back to the
ms_allocatable tree are also added to the ms_free tree. The
ms_free tree is then periodically consumed by an autotrim
thread which systematically walks a top level vdev's metaslabs.
Since the automatic TRIM will skip ranges it considers too small
there is value in occasionally running a full `zpool trim`. This
may occur when the freed blocks are small and not enough time
was allowed to aggregate them. An automatic TRIM and a manual
`zpool trim` may be run concurrently, in which case the automatic
TRIM will yield to the manual TRIM.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Contributions-by: Tim Chase <tim@chase2k.com>
Contributions-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8419Closes#598
Currently, zfs send streams will include a list of all snapshots
on the source side if the '-p' option is provided. This can cause
performance problems on the receive side, especially if those
snapshots aren't present on the destination. These problems arise
because guid_to_name(), which is used for several receive side
functions, will search the entire receive-side pool if it can't
find a snapshot with a matching guid. This patch corrects the
issue by ensuring only streams that require this list of snapshots
include them.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8533
ZFS supports O_RSYNC for read operations and when specified will ensure
the same level of data integrity that O_DSYNC and O_SYNC provides for
writes. O_RSYNC by itself has no effect so it must be combined with
either O_DSYNC or O_SYNC. However, many platforms don't support O_RSYNC
and have mapped O_SYNC to mean O_RSYNC within ZFS. This is incorrect
and causes unnecessary calls to zil_commit. Only platforms which
support O_RSYNC should implement the zil_commit functionality in the
read code path.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#8523
1) As implemented the `zpool labelclear` command overwrites
the calculated offsets of all four vdev labels even when only a
single valid label is found. If the device as been re-purposed
but still contains a valid label this can result in space no
longer owned by ZFS being zeroed. Prevent this by verifying
every label removed is intact before it's overwritten.
2) Address a small bug in zpool_do_labelclear() which prevented
labelclear from working on file vdevs. Only block devices support
BLKFLSBUF, try the ioctl() but when it's reported as unsupported
this should not be fatal.
3) Fix `zpool labelclear` so it can be run on vdevs which were
removed from the pool with `zpool remove`. Additionally, allow
intact but partial labels to be cleared as in the case of a failed
`zpool attach` or `zpool replace`.
4) Remove LABELCLEAR and LABELREAD variables for test cases.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8500Closes#8373Closes#6261
This patch simply adds a missing space in the
ZFS_ERR_FROM_IVSET_GUID_MISSING error message.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8514
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
This patch modifies the zfs_ioc_snapshot_list_next() ioctl to enable it
to take input parameters that alter the way looping through the list of
snapshots is performed. The idea here is to restrict functions that
throw away some of the snapshots returned by the ioctl to a range of
snapshots that these functions actually use. This improves efficiency
and execution speed for some rollback and send operations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8077
Improve the autoconf code for finding libtirpc and do not assume the
headers are in /usr/include/tirpc.
Also remove this assumption from the `rpc/xdr.h` header in libspl and
use the same `#include_next` mechanism that is used for other libspl
headers.
Include pkg.m4 from pkg-config in config/ for PKG_CHECK_MODULES(), the
file license allows this.
Include ax_save_flags.m4 and ax_restore_flags.m4 from autoconf-archive,
the file licenses are compatible. Use the 2012 versions so as not rely
on a more recent autoconf feature AS_VAR_COPY(), which breaks some build
slaves.
Add new macro library `config/find_system_library.m4` which defines the
FIND_SYSTEM_LIBRARY() macro which is a convenience wrapper over using
PKG_CHECK_MODULES() with a fallback to standard library locations and
some sanity checks.
The parameters are:
```
FIND_SYSTEM_LIBRARY(VARIABLE-PREFIX, MODULE, HEADER, HEADER-PREFIXES,
LIBRARY, FUNCTIONS, [ACTION-IF-FOUND], [ACTION-IF-NOT-FOUND])
```
`HEADER-PREFIXES` and `FUNCTIONS` are comma-separated m4 lists.
For libtirpc we are using:
```
FIND_SYSTEM_LIBRARY(LIBTIRPC, [libtirpc], [rpc/xdr.h], [tirpc], [tirpc],
[xdrmem_create], [], [...])
```
The headers are first checked for without the prefixes and then with.
This system works with pkg-config and falls back on checking standard
header/library locations, it can be easily overridden by the user by
setting the `PREFIX_CFLAGS` and `PREFIX_LIBS` variables which are
automatically added to the `./configure --help` output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rafael Kitover <rkitover@gmail.com>
Closes#7422Closes#8313
Preferentially sort by the full path name instead of GUID when determining
which device links to use. This helps ensure that the pool vdevs are named
consistently when multiple links for a device appear in the same directory.
For example, the /dev/disk/by-id/scsi* and /dev/disk/by-id/wwn* links.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kash Pande <kash@tripleback.net>
Closes#8108Closes#8440
Reorder the `zfs create` error messages in order to return the most
specific one first. If none of them apply then an expanded version of
the invalid name message is used.
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8155Closes#8352
We have to use umem_free() instead of free() if we are using
umem_zalloc()
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#8402
Add -h switch to zfs send command to send dataset holds. If
holds are present in the stream, zfs receive will create them
on the target dataset, unless the zfs receive -h option is used
to skip receive of holds.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7513
zfs create, receive and rename can bypass this hierarchy rule. Update
both userland and kernel module to prevent this issue and use pyzfs
unit tests to exercise the ioctls directly.
Note: this commit slightly changes zfs_ioc_create() ABI. This allow to
differentiate a generic error (EINVAL) from the specific case where we
tried to create a dataset below a ZVOL (ZFS_ERR_WRONG_PARENT).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Since the merge of the Linux Solaris Porting Layer source tree into
the ZFS codebase, ZFS is now a double-licensed codebase, with the
former SPL codebase retaining its license (GPLv2+) within the ZFS
source tree.
However, the license files for SPL were not being included in the
tarballs generated by autotools. This change corrects that.
In addition, all the other third party licenses in the codebase are
now properly declared to be included in the dist tarballs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Neal Gompa <ngompa@datto.com>
Closes#8242
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
When MMP was merged the status codes in libzfs_status were not
updated to add the status code for ZPOOL_STATUS_IO_FAILURE_MMP. This
commit corrects this and adds comments to help keep track of which
code is used for which status.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#8148Closes#8222
Following the fix for 9018 (Replace kmem_cache_reap_now() with
kmem_cache_reap_soon), the arc_reclaim_thread() no longer blocks
while reaping. However, the code is still confusing and error-prone,
because this thread has two responsibilities. We should instead
separate this into two threads each with their own responsibility:
1. keep `arc_size` under `arc_c`, by calling `arc_adjust()`, which
improves `arc_is_overflowing()`
2. keep enough free memory in the system, by calling
`arc_kmem_reap_now()` plus `arc_shrink()`, which improves
`arc_available_memory()`.
Furthermore, we can use the zthr infrastructure to separate the
"should we do something" from "do it" parts of the logic, and
normalize the start up / shut down of the threads.
Authored by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@joyent.com>
Reviewed by: Tim Kordas <tim.kordas@joyent.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Brad Lewis <brad.lewis@delphix.com>
Signed-off-by: Brad Lewis <brad.lewis@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/9284
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/de753e34f9Closes#8165
Porting Notes:
* Additional changes to recv_rename_impl() were required due to
encryption code not being merged in OpenZFS yet.
* libzfs_core python bindings (pyzfs) were updated to fully support
both lzc_rename() and lzc_destroy()
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: loli10K <ezomori.nozomu@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9630
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/049ba63Closes#8207
This partially reverts commit 8005ca4 by moving the strlcat()
and strlcpy() compatibility implementations back to their original
location.
In addition, these two functions were added to the AC_CHECK_FUNCS
macro. When these functions are available from the C library,
HAVE_STRLCAT and HAVE_STRLCPY will be defined and library version
used. Otherwise the compatibility version is built.
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8157Closes#8202
Porting Notes:
* Not required for Linux since the zone is always global. But
we'll want this change if we start using the zones code.
Authored by: Andy Fiddaman <omnios@citrus-it.co.uk>
Reviewed by: Jason King <jason.king@joyent.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9880
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bc4c0ff134Closes#8189
This patch corrects a small issue where the wrong error message
was being displayed when the zfs kernel module was not loaded.
This also avoids waiting for the (by default) 10s timeout to see
if the /dev/zfs device appears.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8187
When receiving a send stream with forced rollback on a dataset with
snapshots zfs suggests said snapshots must be removed to successfully
receive the stream; however the message is misleading because it
prints the dataset name instead of one of its snapshots.
$ sudo zfs snap pp/recvfs@snap-orig
$ sudo zfs recv -F pp/recvfs < sendstream
cannot receive new filesystem stream: destination has snapshots (eg. pp/recvfs)
must destroy them to overwrite it
This change simply restores the snapshot name in the error message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8167
This commit fixes the following ASSERT in zfs_receive_one() when
receiving a send stream from a root dataset with the "-e" option:
$ sudo zfs snap source@snap
$ sudo zfs send source@snap | sudo zfs recv -e destination/recv
chopprefix > drrb->drr_toname
ASSERT at libzfs_sendrecv.c:3804:zfs_receive_one()
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8121
Move strlcat() and strlcpy() from .c source files in to the libspl
string.h header. By changing these compatibility functions to static
inline functions they can included as needed without requiring linking
with the libspl.so library.
Remove strnlen() which is barely used in the source, and has been
provided by glibc since v2.10.
Finally, convert four instances of strncpy() to strlcpy() in
libzfs_input_check.c which were causing build warnings when compiling
with gcc 8.2.1. For example:
libzfs_input_check.c: In function ‘zfs_destroy’:
libzfs_input_check.c:651:9: error: ‘strncpy’ specified bound \
4096 equals destination size [-Werror=stringop-truncation]
(void) strncpy(zc.zc_name, dataset, sizeof (zc.zc_name));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8116
Porting Notes:
* Use thread pools (tpool) API instead of introducing taskq interfaces
to libzfs.
* Use pthread_mutext for locks as mutex_t isn't available.
* Ignore alternative libshare initialization since OpenZFS-7955 is
not present on zfsonlinux.
Authored by: Sebastien Roy <seb@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Authored by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Don Brady <don.brady@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8115
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a3f0e2b569Closes#8092
ZFS should be able to build without libudev installed. The recent
change for libzutil inadvertently broke that. Make the libudev code
conditional in zutil_import.c to resolve the build failure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8097
When provided with an invalid 'dedupditto' value zpool prints
a misleading error message:
$ sudo zpool set dedupditto=99 pp
cannot set property for 'pp': property 'dedupditto'(14) not defined
Fix this by printing a meaningful error description for unsupported
'dedupditto' values.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8079
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
Provide a hint in the error message if listing snapshots for a
single dataset fails.
Using -r is not needed to list all snapshots so requiring it when
listing snapshots for a single dataset makes it confusing. This
change will make the error message more clear.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Md Islam <mdnahian@outlook.com>
Closes#8047
This patch resolves a problem where the -G option in both zdb and
ztest would cause the code to call __dprintf() to print zfs_dbgmsg
output. This function was not properly wired to add messages to the
dbgmsg log as it is in userspace and so the messages were simply
dropped. This patch also tries to add some degree of distinction to
dprintf() (which now prints directly to stdout) and zfs_dbgmsg()
(which adds messages to an internal list that can be dumped with
zfs_dbgmsg_print()).
In addition, this patch corrects an issue where ztest used a global
variable to decide whether to dump the dbgmsg buffer on a crash.
This did not work because ztest spins up more instances of itself
using execv(), which did not copy the global variable to the new
process. The option has been moved to the ztest_shared_opts_t
which already exists for interprocess communication.
This patch also changes zfs_dbgmsg_print() to use write() calls
instead of printf() so that it will not fail when used in a signal
handler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8010
Commit 0c6d093 caused a regression in the inherit codepath.
The fix is to restrict the changelist iteration on mountpoints and
add proper handling for 'legacy' mountpoints
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7988Closes#7991
This change moves the bottom half of dmu_send.c (where the receive
logic is kept) into a new file, dmu_recv.c, and does similarly
for receive-related changes in header files.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7982
The code reuse in the definitions of the ASSERT and VERIFY macros result
in expansion of their arguments before they are stringified, which
produces ugly and undesirable output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7884
When using "zfs destroy" on a dataset that is using "sharenfs=on" and
has been automatically exported (by libzfs), the dataset will not be
automatically unexported as it should be. This workflow appears to have
been broken by this commit: 3fd3e56cfd
In that change, the "zfs_unmount" function was modified to use the
"mnt.mnt_special" field when determining the mount point that is being
unmounted, rather than "mnt.mnt_mountp".
As a result, when "mntpt" is passed into "zfs_unshare_proto", it's value
is now the dataset name rather than the mountpoint. Thus, when this
value is used with the "is_shared" function (via "zfs_unshare_proto") it
will not find a match (since that function assumes it'll be passed the
mountpoint) and incorrectly reports that the dataset is not shared.
This can be easily reproduced with the following commands:
$ sudo zpool create tank xvdb
$ sudo zfs create -o sharenfs=on tank/fish
$ sudo zfs destroy tank/fish
$ sudo zfs list -r tank
NAME USED AVAIL REFER MOUNTPOINT
tank 97.5K 7.27G 24K /tank
$ sudo exportfs
/tank/fish <world>
$ sudo cat /etc/dfs/sharetab
/tank/fish - nfs rw,crossmnt
At this point, the "tank/fish" filesystem doesn't exist, but it's still
listed as exported when looking at "exportfs" and "/etc/dfs/sharetab".
Also note, this change brings us back in-sync with the illumos code, as
it pertains to this one line; on illumos, "mnt.mnt_mountp" is used.
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Issue #6143Closes#7941
Modified changelist_gather()ing for the mountpoint property.
Now instead of iterating on all dataset descendants, we read
/proc/self/mounts and iterate on the mounted descendant datasets only.
Switched changelist implementation from a uu_list_* to uu_avl_* in
order to reduce changlist code-path's worst case time complexity.
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7967
There are some issues with the way the seq_file interface is implemented
for kstats backed by linked lists (zfs_dbgmsgs and certain per-pool
debugging info):
* We don't account for the fact that seq_file sometimes visits a node
multiple times, which results in missing messages when read through
procfs.
* We don't keep separate state for each reader of a file, so concurrent
readers will receive incorrect results.
* We don't account for the fact that entries may have been removed from
the list between read syscalls, so reading from these files in procfs
can cause the system to crash.
This change fixes these issues and adds procfs_list, a wrapper around a
linked list which abstracts away the details of implementing the
seq_file interface for a list and exposing the contents of the list
through procfs.
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
External-issue: LX-1211
Closes#7819
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
We want newer versions of libzfs_core to run against an existing
zfs kernel module (i.e. a deferred reboot or module reload after
an update).
Programmatically document, via a zfs_ioc_key_t, the valid arguments
for the ioc commands that rely on nvpair input arguments (i.e. non
legacy commands from libzfs_core). Automatically verify the expected
pairs before dispatching a command.
This initial phase focuses on the non-legacy ioctls. A follow-on
change can address the legacy ioctl input from the zfs_cmd_t.
The zfs_ioc_key_t for zfs_keys_channel_program looks like:
static const zfs_ioc_key_t zfs_keys_channel_program[] = {
{"program", DATA_TYPE_STRING, 0},
{"arg", DATA_TYPE_UNKNOWN, 0},
{"sync", DATA_TYPE_BOOLEAN_VALUE, ZK_OPTIONAL},
{"instrlimit", DATA_TYPE_UINT64, ZK_OPTIONAL},
{"memlimit", DATA_TYPE_UINT64, ZK_OPTIONAL},
};
Introduce four input errors to identify specific input failures
(in addition to generic argument value errors like EINVAL, ERANGE,
EBADF, and E2BIG).
ZFS_ERR_IOC_CMD_UNAVAIL the ioctl number is not supported by kernel
ZFS_ERR_IOC_ARG_UNAVAIL an input argument is not supported by kernel
ZFS_ERR_IOC_ARG_REQUIRED a required input argument is missing
ZFS_ERR_IOC_ARG_BADTYPE an input argument has an invalid type
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7780
This extends our sysfs '/sys/module/zfs' entry to include feature
and property attributes. The primary consumer of this information
is user processes, like the zfs CLI, that need to know what the
current loaded ZFS module supports. The libzfs binary will consult
this information when instantiating the zfs and zpool property
tables and the pool features table.
This introduces 4 kernel objects (dirs) into '/sys/module/zfs'
with corresponding attributes (files):
features.runtime
features.pool
properties.dataset
properties.pool
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7706
Fix a bunch of truncation compiler warnings that show up
on Fedora 28 (GCC 8.0.1).
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #7368Closes#7826Closes#7830
One small integration that was absent from b52563 was
support for zfs recv -o / -x with regards to encryption
parameters. The main use cases of this are as follows:
* Receiving an unencrypted stream as encrypted without
needing to create a "dummy" encrypted parent so that
encryption can be inheritted.
* Allowing users to change their keylocation on receive,
so long as the receiving dataset is an encryption root.
* Allowing users to explicitly exclude or override the
encryption property from an unencrypted properties stream,
allowing it to be received as encrypted.
* Receiving a recursive heirarchy of unencrypted datasets,
encrypting the top-level one and forcing all children to
inherit the encryption.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7650
- Add two new module parameters to icp (icp_aes_impl, icp_gcm_impl)
that control the crypto implementation. At the moment there is a
choice between generic and aesni (on platforms that support it).
- This enables support for AES-NI and PCLMULQDQ-NI on AMD Family
15h (bulldozer) and newer CPUs (zen).
- Modify aes_key_t to track what implementation it was generated
with as key schedules generated with various implementations
are not necessarily interchangable.
Reviewed by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Nathaniel R. Lewis <linux.robotdude@gmail.com>
Closes#7102Closes#7103
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
A memory leak occurs on lines 209 and 213 because the config is not
freed in the error case. The interface to add_config() seems less than
ideal - it would be better if it copied any data necessary from the
config and the caller freed it.
Porting notes:
* This issue had already been resolved on Linux by adding the missing
calls to nvlist_free(). But we'll adopt the upstream fix to keep
the behavior of the code consistent.
Authored by: Sara Hartse <sara.hartse@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9457
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/be86bb8aCloses#7713
While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
Update the SA_COPY_DATA macro to check if architecture supports
efficient unaligned memory accesses at compile time. Otherwise
fallback to using the sa_copy_data() function.
The kernel provided CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is
used to determine availability in kernel space. In user space
the x86_64, x86, powerpc, and sometimes arm architectures will
define the HAVE_EFFICIENT_UNALIGNED_ACCESS macro.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7642Closes#7684
Datasets that are deeply nested (~100 levels) are impractical. We just
put a limit of 50 levels to newly created datasets. Existing datasets
should work without a problem.
The problem can be seen by attempting to create a dataset using the -p
option with many levels:
panic[cpu0]/thread=ffffff01cd282c20: BAD TRAP: type=8 (#df Double fault) rp=ffffffff
fffffffffbc3aa60 unix:die+100 ()
fffffffffbc3ab70 unix:trap+157d ()
ffffff00083d7020 unix:_patch_xrstorq_rbx+196 ()
ffffff00083d7050 zfs:dbuf_rele+2e ()
...
ffffff00083d7080 zfs:dsl_dir_close+32 ()
ffffff00083d70b0 zfs:dsl_dir_evict+30 ()
ffffff00083d70d0 zfs:dbuf_evict_user+4a ()
ffffff00083d7100 zfs:dbuf_rele_and_unlock+87 ()
ffffff00083d7130 zfs:dbuf_rele+2e ()
... The block above repeats once per directory in the ...
... create -p command, working towards the root ...
ffffff00083db9f0 zfs:dsl_dataset_drop_ref+19 ()
ffffff00083dba20 zfs:dsl_dataset_rele+42 ()
ffffff00083dba70 zfs:dmu_objset_prefetch+e4 ()
ffffff00083dbaa0 zfs:findfunc+23 ()
ffffff00083dbb80 zfs:dmu_objset_find_spa+38c ()
ffffff00083dbbc0 zfs:dmu_objset_find+40 ()
ffffff00083dbc20 zfs:zfs_ioc_snapshot_list_next+4b ()
ffffff00083dbcc0 zfs:zfsdev_ioctl+347 ()
ffffff00083dbd00 genunix:cdev_ioctl+45 ()
ffffff00083dbd40 specfs:spec_ioctl+5a ()
ffffff00083dbdc0 genunix:fop_ioctl+7b ()
ffffff00083dbec0 genunix:ioctl+18e ()
ffffff00083dbf10 unix:brand_sys_sysenter+1c9 ()
Porting notes:
* Added zfs_max_dataset_nesting module option with documentation.
* Updated zfs_rename_014_neg.ksh for Linux.
* Increase the zfs.sh stack warning to 15K. Enough time has passed
that 16K can be reasonably assumed to be the default value. It
was increased in the 3.15 kernel released in June of 2014.
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
OpenZFS-issue: https://www.illumos.org/issues/9330
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/757a75aCloses#7681
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
Commit torvalds/linux@95582b0 changes the inode i_atime, i_mtime,
and i_ctime members form timespec's to timespec64's to make them
2038 safe. As part of this change the current_time() function was
also updated to return the timespec64 type.
Resolve this issue by introducing a new inode_timespec_t type which
is defined to match the timespec type used by the inode. It should
be used when working with inode timestamps to ensure matching types.
The timestruc_t type under Illumos was used in a similar fashion but
was specified to always be a timespec_t. Rather than incorrectly
define this type all timespec_t types have been replaced by the new
inode_timespec_t type.
Finally, the kernel and user space 'sys/time.h' headers were aligned
with each other. They define as appropriate for the context several
constants as macros and include static inline implementation of
gethrestime(), gethrestime_sec(), and gethrtime().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7643
The ZoL version of libefi has been modified for Linux in several
places outside the existing __linux__ wrappers. Remove them to
make the code easier to read and so as not to mislead anyone that
these are the sole modifications for Linux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7625
Partition detection for zvol devices was not working correctly
resulting inconsistent partitioning behavior when layering pools
on top of zvols. This isn't a supported configuration but we'd
still like it to work properly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7624
In the case where the pool is loaded without the crypto
keys necessary to playback the intent log, and log device
removal is attempted, a generic busy message is received.
Change the message to inform the user that the datasets
must be mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7518
In pursuit of improving performance on multi-core systems, we should
implements fanned out counters and use them to improve the performance of
some of the arc statistics. These stats are updated extremely frequently,
and can consume a significant amount of CPU time.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Paul Dagnelie <pcd@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8484
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7028a8b92b7
Issue #3752Closes#7462
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
The only remaining consumer of the rwlock compatibility wrappers
is ztest. Remove the wrappers and convert the few remaining
calls to the underlying pthread functions.
rwlock_init() -> pthread_rwlock_init()
rwlock_destroy() -> pthread_rwlock_destroy()
rw_rdlock() -> pthread_rwlock_rdlock()
rw_wrlock() -> pthread_rwlock_wrlock()
rw_unlock() -> pthread_rwlock_unlock()
Note pthread_rwlock_init() defaults to PTHREAD_PROCESS_PRIVATE
which is equivilant to the USYNC_THREAD behavior. There is no
functional change.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7591
We want to be able to pass various settings during import/open of a
pool, which are not only related to rewind. Instead of adding a new
policy and duplicate a bunch of code, we should just rename
rewind_policy to a more generic term like load_policy.
For instance, we'd like to set spa->spa_import_flags from the nvlist,
rather from a flags parameter passed to spa_import as in some cases we
want those flags not only for the import case, but also for the open
case. One such flag could be ZFS_IMPORT_MISSING_LOG (as used in zdb)
which would allow zfs to open a pool when logs are missing.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9235
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d2b1e44Closes#7532
Update bdev_capacity to have wholedisk vdevs query the
size of the underlying block device (correcting for the size
of the efi parition and partition alignment) and therefore detect
expanded space.
Correct vdev_get_stats_ex so that the expandsize is aligned
to metaslab size and new space is only reported if it is large
enough for a new metaslab.
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
External-issue: LX-165
Closes#7546
Issue #7582
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7556
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
9421 zdb should detect and print out the number of "leaked" objects
9422 zfs diff and zdb should explicitly mark objects that are on
the deleted queue
It is possible for zfs to "leak" objects in such a way that they are not
freed, but are also not accessible via the POSIX interface. As the only
way to know that this is happened is to see one of them directly in a
zdb run, or by noting unaccounted space usage, zdb should be enhanced to
count these objects and return failure if some are detected.
We have access to the delete queue through the zfs_get_deleteq function;
we should call it in dump_znode to determine if the object is on the
delete queue. This is not the most efficient possible method, but it is
the simplest to implement, and should suffice for the common case where
there few objects on the delete queue.
Also zfs diff and zdb currently traverse every single dnode in a dataset
and tries to figure out the path of the object by following it's parent.
When an object is placed on the delete queue, for all practical purposes
it's already discarded, it's parent might not exist anymore, and another
object might now have the object number that belonged to the parent.
While all of the above makes sense, when trying to figure out the path
of an object that is on the delete queue, we can run into issues where
either it is impossible to determine the path because the parent is
gone, or another dnode has taken it's place and thus we are returned a
wrong path.
We should therefore avoid trying to determine the path of an object on
the delete queue and mark the object itself as being on the delete queue
to avoid confusion. To achieve this, we currently have two ideas:
1. When putting an object on the delete queue, change it's parent object
number to a known constant that means NULL.
2. When displaying objects, first check if it is present on the delete
queue.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9421
OpenZFS-issue: https://illumos.org/issues/9422
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45ae0dd9caCloses#7500
This commit introduces several changes:
* Update LICENSE and project information
* Give a good PEP8 talk to existing Python source code
* Add RPM/DEB packaging for pyzfs
* Fix some outstanding issues with the existing pyzfs code caused by
changes in the ABI since the last time the code was updated
* Integrate pyzfs Python unittest with the ZFS Test Suite
* Add missing libzfs_core functions: lzc_change_key,
lzc_channel_program, lzc_channel_program_nosync, lzc_load_key,
lzc_receive_one, lzc_receive_resumable, lzc_receive_with_cmdprops,
lzc_receive_with_header, lzc_reopen, lzc_send_resume, lzc_sync,
lzc_unload_key, lzc_remap
Note: this commit slightly changes zfs_ioc_unload_key() ABI. This allow
to differentiate the case where we tried to unload a key on a
non-existing dataset (ENOENT) from the situation where a dataset has
no key loaded: this is consistent with the "change" case where trying
to zfs_ioc_change_key() from a dataset with no key results in EACCES.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7230
When receiving an incremental send stream with intermediary snapshots
zfs_receive_one() does not correctly identify the top-level dataset:
consequently we restore said snapshots as if they were children
datasets in the hierarchy, forcing inheritance of any property received
with 'zfs send -o' and effectively removing any locally set value.
The test case did not correctly verify this situation because it uses
adjacent snapshots, basically testing 'zfs send -i' instead of
'zfs send -I': this commit adds an additional intermediary snapshot to
the test script.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7478
Only filesystems and volumes are valid 'zfs remap' parameters: when
passed a snapshot name zfs_remap_indirects() does not handle the
EINVAL returned from libzfs_core, which results in failing an assertion
and consequently crashing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7454
The timeline of the race condition is the following:
[1] Thread A is about to finish condesing the first vdev in
spa_condense_indirect_thread(), so it calls the
spa_condense_indirect_complete_sync() sync task which sets
the spa_condensing_indirect field to NULL. Waiting for the
sync task to finish, thread A sleeps until the txg is done.
When this happens, thread A will acquire spa_async_lock and
set spa_condense_thread to NULL.
[2] While thread A waits for the txg to finish, thread B which is
running spa_sync() checks whether it should condense the
second vdev in vdev_indirect_should_condense() by checking the
spa_condensing_indirect field which was set to NULL by
spa_condense_indirect_thread() from thread A. So it goes on
and tries to spawn a new condensing thread in
spa_condense_indirect_start_sync() and the aforementioned
assertions fails because thread A has not set spa_condense_thread
to NULL (which is basically the last thing it does before returning).
The main issue here is that we rely on both spa_condensing_indirect
and spa_condense_thread to signify whether a condensing thread is
running. Ideally we would only use one throughout the codebase. In
addition, for managing spa_condense_thread we currently use
spa_async_lock which basically tights condensing to scrubing when
it comes to pausing and resuming those actions during spa export.
This commit introduces the ZTHR infrastructure, which is basically
threads created during spa_load()/spa_create() and exist until we
export or destroy the pool. ZTHRs sleep the majority of the time,
until they are notified to wake up and do some predefined type of work.
In the context of the current bug, a zthr to does the condensing of
indirect mappings replacing the older code that used bare kthreads.
When a pool is created, the condensing zthr is spawned but sleeps
right away, until it is awaken by a signal from spa_sync(). If an
existing pool is loaded, the condensing zthr looks if there is
anything to condense before going to sleep, in case we were condensing
mappings in the pool before it got exported.
The benefits of this solution are the following:
- The current bug is fixed
- spa_condensing_indirect is the sole indicator of whether we are
currently condensing or not
- condensing is more decoupled from the spa_async_thread related
functionality.
As a final note, this commit also sets up the path on upstreaming
other features that use the ZTHR code like zpool checkpoint and
fast clone deletion.
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9079
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3dc606eeCloses#6900
Mirrors are supposed to provide redundancy in the face of whole-disk
failure and silent damage (e.g. some data on disk is not right, but ZFS
hasn't detected the whole device as being broken). However, the current
device removal implementation bypasses some of the mirror's redundancy.
Note that in no case is incorrect data returned, but we might get a
checksum error when we should have been able to find the right data.
There are two underlying problems:
1. When we remove a mirror device, we only read one side of the mirror.
Since we can't verify the checksum, this side may be silently bad, but
the good data is on the other side of the mirror (which we didn't read).
This can cause the removal to "bake in" the busted data – all copies of
the data in the new location are the same, busted version, while we left
the good version behind.
The fix for this is to read and copy both sides of the mirror. If the
old and new vdevs are mirrors, we will read both sides of the old
mirror, and write each copy to the corresponding side of the new mirror.
(If the old and new vdevs have a different number of children, we will
do this as best as possible.) Even though we aren't verifying checksums,
this ensures that as long as there's a good copy of the data, we'll have
a good copy after the removal, even if there's silent damage to one side
of the mirror. If we're removing a mirror that has some silent damage,
we'll have exactly the same damage in the new location (assuming that
the new location is also a mirror).
2. When we read from an indirect vdev that points to a mirror vdev, we
only consider one copy of the data. This can lead to reduced effective
redundancy, because we might read a bad copy of the data from one side
of the mirror, and not retry the other, good side of the mirror.
Note that the problem is not with the removal process, but rather after
the removal has completed (having copied correct data to both sides of
the mirror), if one side of the new mirror is silently damaged, we
encounter the problem when reading the relocated data via the indirect
vdev. Also note that the problem doesn't occur when ZFS knows that one
side of the mirror is bad, e.g. when a disk entirely fails or is
offlined.
The impact is that reads (from indirect vdevs that point to mirrors) may
return a checksum error even though the good data exists on one side of
the mirror, and scrub doesn't repair all data on the mirror (if some of
it is pointed to via an indirect vdev).
The fix for this is complicated by "split blocks" - one logical block
may be split into two (or more) pieces with each piece moved to a
different new location. In this case we need to read all versions of
each split (one from each side of the mirror), and figure out which
combination of versions results in the correct checksum, and then repair
the incorrect versions.
This ensures that we supply the same redundancy whether you use device
removal or not. For example, if a mirror has small silent errors on all
of its children, we can still reconstruct the correct data, as long as
those errors are at sufficiently-separated offsets (specifically,
separated by the largest block size - default of 128KB, but up to 16MB).
Porting notes:
* A new indirect vdev check was moved from dsl_scan_needs_resilver_cb()
to dsl_scan_needs_resilver(), which was added to ZoL as part of the
sequential scrub work.
* Passed NULL for zfs_ereport_post_checksum()'s zbookmark_phys_t
parameter. The extra parameter is unique to ZoL.
* When posting indirect checksum errors the ABD can be passed directly,
zfs_ereport_post_checksum() is not yet ABD-aware in OpenZFS.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9290
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/591Closes#6900
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
This change adds five new tests to the ZTS:
* zpool_split_cliargs: verify command line options and arguments
* zpool_split_devices: verify zpool split accepts a device list
* zpool_split_encryption: verify zpool can split encrypted pools
* zpool_split_props: verify zpool split can set property values
* zpool_split_vdevs: verify vdev layout when splitting the pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7409
calloc(3) takes `nelem` (or `nmemb` in glibc) first, and then size of
elements. No difference expected for having these in reverse order,
however should follow the standard.
http://pubs.opengroup.org/onlinepubs/009695399/functions/calloc.html
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7405
Authored by: Mike Gerdts <mike.gerdts@joyent.com>
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Don Brady <don.brady@delphix.com>
Porting Notes:
* Adopted destroy_dataset in ZTS test cleanup
* Use ksh shebang instead of bash for new tests
OpenZFS-issue: https://www.illumos.org/issues/9286
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/723d0c85Closes#7387
Commit e4010f2 accidentally allows zpool to set pool features to
"disabled"; this should only be allowed at pool creation. This commit
adds additional checks and test coverage to 'zpool set'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7402
This patch corrects a small issue where two error messages
in the code that checks for invalid keylocations were
swapped.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7418
Fix a bunch of (mostly) sprintf/snprintf truncation compiler
warnings that show up on Fedora 28 (GCC 8.0.1).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7361Closes#7368
Adds a devid for nvme devices. This is very similar to how the
other 'bus' (scsi|sata|usb) devids are generated. The devid
resides in a name/value pair in the leaf vdevs in a zpool config.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7356
When given an empty string as a rootds value, bootcfg -C fails with
the error message 'could not set nextboot: '' is an invalid name'.
This should be allowed because it represents clearing the nextboot
configuration.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9193
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/504645d227Closes#7230
This treats /dev/nvme.. devices the same way as /dev/sd... devices. The
motivation behind this is that whole disk detection did not work on nvme
SSDs without that, because it DKC_UNKNOWN was returned for such devices.
Perhaps there should be a separate DKC_ type for this, but I don't know
enough about the code to know the implications of that.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: timor <timor.dd@googlemail.com>
Closes#7304
The changes piggyback JSON output support on top of channel programs
(#6558). This way the JSON output support is targeted to scripting
use cases and is easily maintainable since it really only touches
one function (zfs_do_channel_program()).
This patch ports Joyent's JSON nvlist library from illumos to enable
easy JSON printing of channel program output nvlist. To keep the
delta small I also took advantage of the fact that printing in
zfs_do_channel_program() was almost always done before exiting
the program.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7281
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
Historically a dynamic misc minor number was registered for the
/dev/zfs device in order to prevent minor number collisions. This
was fine but it prevented us from being able to use the kernel
module auto-loaded which requires a known reserved value.
Resolve this issue by adding a configure test to find an available
misc minor number which can then be used in MODULE_ALIAS_MISCDEV at
build time. By adding this alias the zfs kmod is added to the list
of known static-nodes and the systemd-tmpfiles-setup-dev service
will create a /dev/zfs character device at boot time.
This in turn allows us to update the 90-zfs.rules file to make it
aware this is a static node. The upshot of this is that whenever
a process (zpool, zfs, zed) opens the /dev/zfs the kmods will be
automatic loaded. This even works for unprivileged users so there
is no longer a need to manually load the modules at boot time.
As an additional bonus the zed now no longer needs to start after
the zfs-import.service since it will trigger the module load.
In the unlikely event the minor number we selected conflicts with
another out of tree unregistered minor number the code falls back
to dynamically allocating it. In this case the modules again
must be manually loaded.
Note that due to the change in the method of registering the minor
number the zimport.sh test case may incorrectly fail when the
static node for the installed packages is created instead of the
dynamic one. This issue will only transiently impact zimport.sh
for this single commit when we transition and are mixing and
matching methods.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7287
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
1) The Coverity Scan reports some issues for the project
quota patch, including:
1.1) zfs_prop_get_userquota() directly uses the const quota
type value as the condition check by wrong.
1.2) dmu_objset_userquota_get_ids() may cause dnode::dn_newgid
to be overwritten by dnode::dn->dn_oldprojid.
2) This patch fixes related issues. It also enhances the logic
for zfs_project_item_alloc() to avoid buffer overflow.
3) Skip project quota ability check if does not change project
quota related things (id or flag). Otherwise, it will cause
chattr (for other non project quota flags) operation failed
if project quota disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
Closes#7251Closes#7265
This change implements 'zfs send -b' which can be used to send only
received property values whether or not they are overridden by local
settings.
This can be very useful during "restore" operations from a backup pool
because it allows to send only the property values originally sent
from the backup source, even though they were later modified on the
destination either by a 'zfs set' operation, explicit 'zfs inherit' or
overridden during the receive process via 'zfs receive -o|-x'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7156
The current design of ZFS encryption only allows a dataset to
have one DSL Crypto Key at a time. As a result, it is important
that the zfs receive code ensures that only one key can be in use
at a time for a given DSL Directory. zfs receive -F complicates
this, since the new dataset is received as a clone of the existing
one so that an atomic switch can be done at the end. To prevent
confusion about which dataset is actually encrypted a check was
added to ensure that encrypted datasets cannot use zfs recv -F to
completely replace existing datasets. Unfortunately, the check did
not take into account unencrypted datasets being overriden by
encrypted ones as a case.
Along the same lines, the code also failed to ensure that raw
recieves could not be done on top of existing unencrypted
datasets, which causes amny problems since the new stream cannot
be decrypted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7199
Because resuming from a token requires "guid" -> "snapshot" mapping
we have to walk the whole dataset hierarchy to find the right snapshot
to send; when both source and destination exists, for an incremental
resumable stream, libzfs gets confused and picks up the wrong snapshot
to send from: this results in attempting to send
"destination@snap1 -> source@snap2"
instead of
"source@snap1 -> source@snap2"
which fails with a "Invalid cross-device link" error (EXDEV).
Fix this by adjusting the logic behind dataset traversal in
zfs_iter_children() to pick the right snapshot to send from.
Additionally update dry-run 'zfs send -t' to print its output to
stderr: this is consistent with other dry-run commands.
Patch Notes:
Reconciled differences between OpenZFS and
aee1dd4d98.
Authored by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.home-2000.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8940
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9f7867c206Closes#7171
Project quota is a new ZFS system space/object usage accounting
and enforcement mechanism. Similar as user/group quota, project
quota is another dimension of system quota. It bases on the new
object attribute - project ID.
Project ID is a numerical value to indicate to which project an
object belongs. An object only can belong to one project though
you (the object owner or privileged user) can change the object
project ID via 'chattr -p' or 'zfs project [-s] -p' explicitly.
The object also can inherit the project ID from its parent when
created if the parent has the project inherit flag (that can be
set via 'chattr +P' or 'zfs project -s [-p]').
By accounting the spaces/objects belong to the same project, we
can know how many spaces/objects used by the project. And if we
set the upper limit then we can control the spaces/objects that
are consumed by such project. It is useful when multiple groups
and users cooperate for the same project, or a user/group needs
to participate in multiple projects.
Support the following commands and functionalities:
zfs set projectquota@project
zfs set projectobjquota@project
zfs get projectquota@project
zfs get projectobjquota@project
zfs get projectused@project
zfs get projectobjused@project
zfs projectspace
zfs allow projectquota
zfs allow projectobjquota
zfs allow projectused
zfs allow projectobjused
zfs unallow projectquota
zfs unallow projectobjquota
zfs unallow projectused
zfs unallow projectobjused
chattr +/-P
chattr -p project_id
lsattr -p
This patch also supports tree quota based on the project quota via
"zfs project" commands set as following:
zfs project [-d|-r] <file|directory ...>
zfs project -C [-k] [-r] <file|directory ...>
zfs project -c [-0] [-d|-r] [-p id] <file|directory ...>
zfs project [-p id] [-r] [-s] <file|directory ...>
For "df [-i] $DIR" command, if we set INHERIT (project ID) flag on
the $DIR, then the proejct [obj]quota and [obj]used values for the
$DIR's project ID will be shown as the total/free (avail) resource.
Keep the same behavior as EXT4/XFS does.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by Ned Bass <bass6@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
TEST_ZIMPORT_POOLS="zol-0.6.1 zol-0.6.2 master"
Change-Id: Ib4f0544602e03fb61fd46a849d7ba51a6005693c
Closes#6290
Receiving an incremental stream after an interrupted "zfs receive -s"
fails with the message "dataset is busy": this is because we still have
the hidden clone ../%recv from the resumable receive.
Improve the error message suggesting the existence of a partially
complete resumable stream from "zfs receive -s" which can be either
aborted ("zfs receive -A") or resumed ("zfs send -t").
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7129Closes#7154
8520 lzc_rollback_to should support rolling back to origin
7198 libzfs should gracefully handle EINVAL from lzc_rollback
lzc_rollback_to() should support rolling back to a clone's origin.
The current checks in zfs_ioc_rollback() would not allow that
because the origin snapshot belongs to a different filesystem.
The overly restrictive check was in introduced in 7600, but it
was not a regression as none of the existing tools provided a
way to rollback to the origin.
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8520
OpenZFS-issue: https://www.illumos.org/issues/7198
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/78a5a1a25aCloses#7150
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
We want to be able to run channel programs outside of synching
context. This would greatly improve performance for channel programs
that just gather information, as they won't have to wait for synching
context anymore.
=== What is implemented?
This feature introduces the following:
- A new command line flag in "zfs program" to specify our intention
to run in open context. (The -n option)
- A new flag/option within the channel program ioctl which selects
the context.
- Appropriate error handling whenever we try a channel program in
open-context that contains zfs.sync* expressions.
- Documentation for the new feature in the manual pages.
=== How do we handle zfs.sync functions in open context?
When such a function is found by the interpreter and we are running
in open context we abort the script and we spit out a descriptive
runtime error. For example, given the script below ...
arg = ...
fs = arg["argv"][1]
err = zfs.sync.destroy(fs)
msg = "destroying " .. fs .. " err=" .. err
return msg
if we run it in open context, we will get back the following error:
Channel program execution failed:
[string "channel program"]:3: running functions from the zfs.sync
submodule requires passing sync=TRUE to lzc_channel_program()
(i.e. do not specify the "-n" command line argument)
stack traceback:
[C]: in function 'destroy'
[string "channel program"]:3: in main chunk
=== What about testing?
We've introduced new wrappers for all channel program tests that
run each channel program as both (startard & open-context) and
expect the appropriate behavior depending on the program using
the zfs.sync module.
OpenZFS-issue: https://www.illumos.org/issues/8677
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/17a49e15Closes#6558
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
ZFS channel programs should be able to create snapshots.
In addition to the base snapshot functionality, this entails extra
logic to handle edge cases which were formerly not possible, such as
creating then destroying a snapshot in the same transaction sync.
OpenZFS-issue: https://www.illumos.org/issues/8600
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/68089b8b
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
When used in conjunction with one of '-e' or '-d' zfs receive options
none of the properties requested to be set (-o) are actually applied:
this is caused by a wrong assumption made about the toplevel dataset
in zfs_receive_one().
Fix this by correctly detecting the toplevel dataset.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7088
When we know which devices have the pool we are looking for, sometime
it's better if we can directly pass those device paths to zpool import
instead of letting it to search through all unrelated stuff, which might
take a lot of time if you have hundreds of disks.
This patch allows option -d <dev_path> to zpool import. You can have
multiple pairs of -d <dev_path>, and zpool import will only search
through those devices. For example:
zpool import -d /dev/sda -d /dev/sdb
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7077
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Add "spare" and "replacing" to the list of interior vdev types in
zpool_vdev_is_interior(), alongside the existing "mirror" and "raidz".
This fixes running "zinject -d" and "zpool clear" on spare and replacing
vdevs.
Authored by: Alan Somers <asomers@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8641
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9a36801382Closes#7060
For ztest, which is solely for testing, using a pseudo random
is entirely reasonable. Using /dev/urandom ensures the system
entropy pool doesn't get depleted thus stalling the testing.
This is a particular problem when testing in VMs.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7017Closes#7036
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
The functionality provided by this header is not required by any
of the ZFS user space code. Minimal functionality was provided
in commit c28a677 which added include/sys/frame.h.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6960Closes#6972
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
Problem
=======
The current implementation of zil_commit() can introduce significant
latency, beyond what is inherent due to the latency of the underlying
storage. The additional latency comes from two main problems:
1. When there's outstanding ZIL blocks being written (i.e. there's
already a "writer thread" in progress), then any new calls to
zil_commit() will block waiting for the currently oustanding ZIL
blocks to complete. The blocks written for each "writer thread" is
coined a "batch", and there can only ever be a single "batch" being
written at a time. When a batch is being written, any new ZIL
transactions will have to wait for the next batch to be written,
which won't occur until the current batch finishes.
As a result, the underlying storage may not be used as efficiently
as possible. While "new" threads enter zil_commit() and are blocked
waiting for the next batch, it's possible that the underlying
storage isn't fully utilized by the current batch of ZIL blocks. In
that case, it'd be better to allow these new threads to generate
(and issue) a new ZIL block, such that it could be serviced by the
underlying storage concurrently with the other ZIL blocks that are
being serviced.
2. Any call to zil_commit() must wait for all ZIL blocks in its "batch"
to complete, prior to zil_commit() returning. The size of any given
batch is proportional to the number of ZIL transaction in the queue
at the time that the batch starts processing the queue; which
doesn't occur until the previous batch completes. Thus, if there's a
lot of transactions in the queue, the batch could be composed of
many ZIL blocks, and each call to zil_commit() will have to wait for
all of these writes to complete (even if the thread calling
zil_commit() only cared about one of the transactions in the batch).
To further complicate the situation, these two issues result in the
following side effect:
3. If a given batch takes longer to complete than normal, this results
in larger batch sizes, which then take longer to complete and
further drive up the latency of zil_commit(). This can occur for a
number of reasons, including (but not limited to): transient changes
in the workload, and storage latency irregularites.
Solution
========
The solution attempted by this change has the following goals:
1. no on-disk changes; maintain current on-disk format.
2. modify the "batch size" to be equal to the "ZIL block size".
3. allow new batches to be generated and issued to disk, while there's
already batches being serviced by the disk.
4. allow zil_commit() to wait for as few ZIL blocks as possible.
5. use as few ZIL blocks as possible, for the same amount of ZIL
transactions, without introducing significant latency to any
individual ZIL transaction. i.e. use fewer, but larger, ZIL blocks.
In theory, with these goals met, the new allgorithm will allow the
following improvements:
1. new ZIL blocks can be generated and issued, while there's already
oustanding ZIL blocks being serviced by the storage.
2. the latency of zil_commit() should be proportional to the underlying
storage latency, rather than the incoming synchronous workload.
Porting Notes
=============
Due to the changes made in commit 119a394ab0, the lifetime of an itx
structure differs than in OpenZFS. Specifically, the itx structure is
kept around until the data associated with the itx is considered to be
safe on disk; this is so that the itx's callback can be called after the
data is committed to stable storage. Since OpenZFS doesn't have this itx
callback mechanism, it's able to destroy the itx structure immediately
after the itx is committed to an lwb (before the lwb is written to
disk).
To support this difference, and to ensure the itx's callbacks can still
be called after the itx's data is on disk, a few changes had to be made:
* A list of itxs was added to the lwb structure. This list contains
all of the itxs that have been committed to the lwb, such that the
callbacks for these itxs can be called from zil_lwb_flush_vdevs_done(),
after the data for the itxs is committed to disk.
* A list of itxs was added on the stack of the zil_process_commit_list()
function; the "nolwb_itxs" list. In some circumstances, an itx may
not be committed to an lwb (e.g. if allocating the "next" ZIL block
on disk fails), so this list is used to keep track of which itxs
fall into this state, such that their callbacks can be called after
the ZIL's writer pipeline is "stalled".
* The logic to actually call the itx's callback was moved into the
zil_itx_destroy() function. Since all consumers of zil_itx_destroy()
were effectively performing the same logic (i.e. if callback is
non-null, call the callback), it seemed like useful code cleanup to
consolidate this logic into a single function.
Additionally, the existing Linux tracepoint infrastructure dealing with
the ZIL's probes and structures had to be updated to reflect these code
changes. Specifically:
* The "zil__cw1" and "zil__cw2" probes were removed, so they had to be
removed from "trace_zil.h" as well.
* Some of the zilog structure's fields were removed, which affected
the tracepoint definitions of the structure.
* New tracepoints had to be added for the following 3 new probes:
* zil__process__commit__itx
* zil__process__normal__itx
* zil__commit__io__error
OpenZFS-issue: https://www.illumos.org/issues/8585
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5d95a3aCloses#6566
Resolve new warnings and errors from cppcheck v1.80.
* [lib/libshare/libshare.c:543]: (warning)
Possible null pointer dereference: protocol
* [lib/libzfs/libzfs_dataset.c:2323]: (warning)
Possible null pointer dereference: srctype
* [lib/libzfs/libzfs_import.c:318]: (error)
Uninitialized variable: link
* [module/zfs/abd.c:353]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:353]: (error) Uninitialized variable: i
* [module/zfs/abd.c:385]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:385]: (error) Uninitialized variable: i
* [module/zfs/abd.c:553]: (error) Uninitialized variable: i
* [module/zfs/abd.c:553]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:763]: (error) Uninitialized variable: i
* [module/zfs/abd.c:763]: (error) Uninitialized variable: sg
* [module/zfs/abd.c:305]: (error) Uninitialized variable: tmp_page
* [module/zfs/zpl_xattr.c:342]: (warning)
Possible null pointer dereference: value
* [module/zfs/zvol.c:208]: (error) Uninitialized variable: p
Convert the following suppression to inline.
* [module/zfs/zfs_vnops.c:840]: (error)
Possible null pointer dereference: aiov
Exclude HAVE_UIO_ZEROCOPY and HAVE_DNLC from analysis since
these macro's will never be defined until this functionality
is implemented.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6879
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Porting Notes:
- The OpenZFS patch added nicenum_scale() and nicenum() to a
library not used by ZFS. Rather than pull in a new dependency
the version of nicenum in lib/libzpool/util.c was simply
replaced with the new one.
Reviewed by: Sebastian Wiedenroth <wiedi@frubar.net>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Yuri Pankov <yuripv@gmx.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Authored by: Jason King <jason.brian.king@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/640
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0a055120Closes#6796
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
Add get functions to match existing ones.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Ramsden <johnramsden@riseup.net>
Closes#6308
Currently the function documentation states that two strings are
allocated, this is outdated. Only one char ** parameter is passed
into the function now, clearly only a pointer to a single string
is returned and needs to be free'd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6754
This PR includes fixes for bugs and documentation issues found
after the encryption patch was merged and general code improvements
for long-term maintainability.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #6526Closes#6639Closes#6703
Cloese #6706Closes#6714Closes#6595
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
CPPASCOMPILE and LTCPPASCOMPILE all include DEFAULT_INCLUDES,
hence it's unnecessary to add the includes again.
Signed-off-by: Pengcheng Xu <i@jsteward.moe>
It's important to respect the user's CFLAGS as mismatched -mcpu
will directly result in the assembler not able to produce correct
code. Fixes#6733.
Signed-off-by: Pengcheng Xu <i@jsteward.moe>
Because resuming from a token requires "guid" -> "snapshot" mapping
we have to walk the whole dataset hierarchy to find the right snapshot
to send; when both source and destination exists, for an incremental
resumable stream, libzfs gets confused and picks up the wrong snapshot
to send from: this results in attempting to send
"destination@snap1 -> source@snap2"
instead of
"source@snap1 -> source@snap2"
which fails with a "Invalid cross-device link" error (EXDEV).
Fix this by adjusting the logic behind dataset traversal in
zfs_iter_children() to pick the right snapshot to send from.
Additionally update dry-run 'zfs send -t' to print its output to
stderr: this is consistent with other dry-run commands.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6618Closes#6619Closes#6623
ZFS buildbot STYLE builder was moved to Ubuntu 17.04
which has a newer version of cppcheck. Handle the
new cppcheck errors.
uu_* functions removed in this commit were unused
and effectively dead code. They are now retired.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6653
FRU and LIBTOPO support are illumos only features that will not be ported to
Linux and make the code more complicated than necessary. This commit
makes way for further cleanups of the zed/FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6641
This change allow (ref)reservation to be set larger than the current
ZVOL size: this is safe as we normally set refreservation > volsize
at ZVOL creation time when we account for metadata.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2468Closes#6610
This leverages the functionality introduced in cf7684b to expose
verbose, dry-run and parsable 'zfs send' options for bookmarks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3666Closes#6601
Add a small wrapper around libzfs_core`lzc_send_space() to libzfs so
that every legacy ZFS_IOC_SEND consumer, along with their userland
counterpart estimate_ioctl(), can leverage ZFS_IOC_SEND_SPACE to
request send space estimation.
The legacy functionality in zfs_ioc_send() is left untouched for
compatibility purposes.
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6029
Andrea Gelmini
Matthew Ahrens
Paul Dagnelie
Ryan Moeller
наб
John Gallagher
felixdoerre
Brian Atkinson
George Amanakis
Adam D. Moss
Jason King
Matthew Ahrens
Joao Carlos Mendes Luis
alaviss
Matthew Macy
alex
Mariusz Zaborski
Brian Behlendorf
Christian Schwarz
Attila Fülöp
Romain Dolbeau
Kyle Evans
Tom Caputi
Nick Black
Tony Hutter
Paul Zuchowski
InsanePrawn
Prakash Surya
Chunwei Chen
Richard Yao
Matthew Macy
Ryan Moeller
John Gallagher
Andriy Gapon
Pavel Zakharov
Michael Niewöhner
Serapheim Dimitropoulos
Tomohiro Kusumi
loli10K
Mike Gerdts
Don Brady
Harry Mallon
Tulsi Jain
TerraTech
Richard Laager
Sara Hartse
TerraTech
George Wilson
Alek P
Rafael Kitover
kpande
Damian Wojsław
Igor K
Neal Gompa (ニール・ゴンパ)
George Wilson
bunder2015
Brad Lewis
Andy Fiddaman
Sebastien Roy
Md Islam
Paul Dagnelie
Andrew Stormont
Nathan Lewis
sara hartse
Serapheim Dimitropoulos
Chunwei Chen
loli10K
timor
Olaf Faaland
Nasf-Fan
Chris Williamson
Chunwei Chen
Yuri Pankov
George G
Jason King
Arkadiusz Bubała
John
Tobin Harding
KireinaHoro
Giuseppe Di Natale
David Quigley
