The DDT is really inefficient on 4k and up vdevs, because it always
allocates 4k blocks, and while compression could save us somewhat
at ashift 9, that stops being true.
So let's change the default to 32 KiB, which seems like a reasonable
compromise between improved space savings and inflated write sizes
for DDT updates.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14654
Switch FIFO queues (SYNC/TRIM) and active queue of vdev queue from
time-sorted AVL-trees to simple lists. AVL-trees are too expensive
for such a simple task. To change I/O priority without searching
through the trees, add io_queue_state field to struct zio.
To not check number of queued I/Os for each priority add vq_cqueued
bitmap to struct vdev_queue. Update it when adding/removing I/Os.
Make vq_cactive a separate array instead of struct vdev_queue_class
member. Together those allow to avoid lots of cache misses when
looking for work in vdev_queue_class_to_issue().
Introduce deadline of ~0.5s for LBA-sorted queues. Before this I
saw some I/Os waiting in a queue for up to 8 seconds and possibly
more due to starvation. With this change I no longer see it. I
had to slightly more complicate the comparison function, but since
it uses all the same cache lines the difference is minimal. For a
sequential I/Os the new code in vdev_queue_io_to_issue() actually
often uses more simple avl_first(), falling back to avl_find() and
avl_nearest() only when needed.
Arrange members in struct zio to access only one cache line when
searching through vdev queues. While there, remove io_alloc_node,
reusing the io_queue_node instead. Those two are never used same
time.
Remove zfs_vdev_aggregate_trim parameter. It was disabled for 4
years since implemented, while still wasted time maintaining the
offset-sorted tree of TRIM requests. Just remove the tree.
Remove locking from txg_all_lists_empty(). It is racy by design,
while 2 pair of locks/unlocks take noticeable time under the vdev
queue lock.
With these changes in my tests with volblocksize=4KB I measure vdev
queue lock spin time reduction by 50% on read and 75% on write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14925
It's been observed that in certain workloads (zvol-related being a
big one), ZFS will end up spending a large amount of time spinning
up taskqs only to tear them down again almost immediately, then
spin them up again...
I noticed this when I looked at what my mostly-idle system was doing
and wondered how on earth taskq creation/destroy was a bunch of time...
So I added a configurable delay to avoid it tearing down tasks the
first time it notices them idle, and the total number of threads at
steady state went up, but the amount of time being burned just
tearing down/turning up new ones almost vanished.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14938
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
It was previously available only to FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Seagate Technology LLC
Closes#14718
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
When testing distributed rebuild performance with more capable
hardware it was observed than increasing the zfs_rebuild_vdev_limit
to 64M reduced the rebuild time by 17%. Beyond 64MB there was
some improvement (~2%) but it was not significant when weighed
against the increased memory usage. Memory usage is capped at 1/4
of arc_c_max.
Additionally, vr_bytes_inflight_max has been moved so it's updated
per-metaslab to allow the size to be adjust while a rebuild is
running.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
For HDD based pools the default zfs_scan_vdev_limit of 4M
per-vdev can significantly limit the maximum scrub performance.
Increasing the default to 16M can double the scrub speed from
80 MB/s per disk to 160 MB/s per disk.
This does increase the memory footprint during scrub/resilver
but given the performance win this is a reasonable trade off.
Memory usage is capped at 1/4 of arc_c_max. Note that number
of outstanding I/Os has not changed and is still limited by
zfs_vdev_scrub_max_active.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
When resilvering the estimated time remaining is calculated using
the average issue rate over the current pass. Where the current
pass starts when a scan was started, or restarted, if the pool
was exported/imported.
For dRAID pools in particular this can result in wildly optimistic
estimates since the issue rate will be very high while scanning
when non-degraded regions of the pool are scanned. Once repair
I/O starts being issued performance drops to a realistic number
but the estimated performance is still significantly skewed.
To address this we redefine a pass such that it starts after a
scanning phase completes so the issue rate is more reflective of
recent performance. Additionally, the zfs_scan_report_txgs
module option can be set to reset the pass statistics more often.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14410
Despite all optimizations, tests on actual hardware show that FreeBSD
kernel can't sleep for less then ~2us. Similar tests on Linux show
~50us delay at least from nanosleep() (haven't tested inside kernel).
It means that on very fast log device ZIL may not be able to satisfy
zfs_commit_timeout_pct block commit timeout, increasing log latency
more than desired.
Handle that by introduction of zil_min_commit_timeout parameter,
specifying minimal timeout value where additional delays to aggregate
writes may be skipped. Also skip delays if the LWB is more than 7/8
full, that often happens if I/O sizes are constant and match one of
LWB sizes. Both things are applied only if there were no already
outstanding log blocks, that may indicate single-threaded workload,
that by definition can not benefit from the commit delays.
While there, add short time moving average to zl_last_lwb_latency to
make it more stable.
Tests of single-threaded 4KB writes to NVDIMM SLOG on FreeBSD show IOPS
increase by 9% instead of expected 5%. For zfs_commit_timeout_pct of
1 there IOPS increase by 5.5% instead of expected 1%.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14418
It was changed in e99932f7de,
but without docs update.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#14400
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
This change turns `MZAP_MAX_BLKSZ` into a `ZFS_MODULE_PARAM()` called
`zap_micro_max_size`. As a result, we can experiment with different
micro ZAP sizes to improve directory size scaling.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Co-authored-by: Toomas Soome <toomas.soome@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14292
This saves 40 bytes per full ARC header, reducing it on FreeBSD from
240 to 200 bytes on production bits.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14315
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14179
Correct new mandoc errors.
```
STYLE: input text line longer than 80 bytes
STYLE: no blank before trailing delimiter
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
The quota for ZVOLs is set to the size of the volume. When the quota
reaches the maximum, there isn't an excellent way to check if the new
writers are overwriting the data or if they are inserting a new one.
Because of that, when we reach the maximum quota, we wait till txg is
flushed. This is causing a significant fluctuation in bandwidth.
In the case of ZVOL, the quota is enforced by the volsize, so we
can omit it.
This commit adds a sysctl thats allow to control if the quota mechanism
should be enforced or not.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13838
Some of our customers have been occasionally hitting zfs import failures
in Linux because udevd doesn't create the by-id symbolic links in time
for zpool import to use them. The main issue is that the
systemd-udev-settle.service that zfs-import-cache.service and other
services depend on is racy. There is also an openzfs issue filed (see
https://github.com/openzfs/zfs/issues/10891) outlining the problem and
potential solutions.
With the proper solutions being significant in terms of complexity and
the priority of the issue being low for the time being, this patch
exposes `zfs_vdev_open_timeout_ms` as a tunable so people that are
experiencing this issue often can increase it as a workaround.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14133
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
The current value causes significant artificial slowdown during mass
parallel file removal, which can be observed both on FreeBSD and Linux
when running real workloads.
Sample results from Linux doing make -j 96 clean after an allyesconfig
modules build:
before: 4.14s user 6.79s system 48% cpu 22.631 total
after: 4.17s user 6.44s system 153% cpu 6.927 total
FreeBSD results in the ticket.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13932Closes#13938
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Incorrectly sizing the array of hash locks used to protect the
dbuf hash table can lead to contention and reduce performance.
We could unconditionally allocate a larger array for the locks
but it's wasteful, particularly for a low-memory system.
Instead, dynamically allocate the array of locks and scale
it based on total system memory.
Additionally, add a new `dbuf_mutex_cache_shift` module option
which can be used to override the hash lock array size. This is
disabled by default (dbuf_mutex_hash_shift=0) and can only be
set at module load time. The minimum target array size is set
to 8192, this matches the current constant value.
Note that the count of the dbuf hash table and count of the
mutex array were added to the /proc/spl/kstat/zfs/dbufstats
kstat.
Finally, this change removes the _KERNEL conditional checks.
These were not required since for the user space build there
is no difference between the kmem and vmem interfaces.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13928
The zfs module parameter zfs_blake3_impl got no manual page entry while
adding BLAKE3 to OpenZFS. This commit adds the required notes about the
parameter into zfs.4
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@freqlabs.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
I see a few issues in the issue tracker that might be aided by being
able to turn this on. We have no module parameter for it, so I would
like to add one.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13874
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
Add support for the kernel's block multiqueue (blk-mq) interface in
the zvol block driver. blk-mq creates multiple request queues on
different CPUs rather than having a single request queue. This can
improve zvol performance with multithreaded reads/writes.
This implementation uses the blk-mq interfaces on 4.13 or newer
kernels. Building against older kernels will fall back to the
older BIO interfaces.
Note that you must set the `zvol_use_blk_mq` module param to
enable the blk-mq API. It is disabled by default.
In addition, this commit lets the zvol blk-mq layer process whole
`struct request` IOs at a time, rather than breaking them down
into their individual BIOs. This reduces dbuf lock contention
and overhead versus the legacy zvol submit_bio() codepath.
sequential dd to one zvol, 8k volblocksize, no O_DIRECT:
legacy submit_bio() 292MB/s write 453MB/s read
this commit 453MB/s write 885MB/s read
It also introduces a new `zvol_blk_mq_chunks_per_thread` module
parameter. This parameter represents how many volblocksize'd chunks
to process per each zvol thread. It can be used to tune your zvols
for better read vs write performance (higher values favor write,
lower favor read).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13148
Issue #12483
That'll teach me to try and recall them from the definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13519
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12746
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Max Zettlmeißl <max@zettlmeissl.de>
Closes#12784
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
Rich Ercolani
Alexander Motin
George Amanakis
Rob N
Brian Behlendorf
George Melikov
Mateusz Piotrowski
Mateusz Piotrowski
Allan Jude
szubersk
Mariusz Zaborski
Mariusz Zaborski
Serapheim Dimitropoulos
Richard Yao
Mateusz Guzik
Tino Reichardt
Alek P
Tony Hutter
WHR
Jitendra Patidar
наб
Ryan Moeller
chrisrd
maxz