Switch FIFO queues (SYNC/TRIM) and active queue of vdev queue from
time-sorted AVL-trees to simple lists. AVL-trees are too expensive
for such a simple task. To change I/O priority without searching
through the trees, add io_queue_state field to struct zio.
To not check number of queued I/Os for each priority add vq_cqueued
bitmap to struct vdev_queue. Update it when adding/removing I/Os.
Make vq_cactive a separate array instead of struct vdev_queue_class
member. Together those allow to avoid lots of cache misses when
looking for work in vdev_queue_class_to_issue().
Introduce deadline of ~0.5s for LBA-sorted queues. Before this I
saw some I/Os waiting in a queue for up to 8 seconds and possibly
more due to starvation. With this change I no longer see it. I
had to slightly more complicate the comparison function, but since
it uses all the same cache lines the difference is minimal. For a
sequential I/Os the new code in vdev_queue_io_to_issue() actually
often uses more simple avl_first(), falling back to avl_find() and
avl_nearest() only when needed.
Arrange members in struct zio to access only one cache line when
searching through vdev queues. While there, remove io_alloc_node,
reusing the io_queue_node instead. Those two are never used same
time.
Remove zfs_vdev_aggregate_trim parameter. It was disabled for 4
years since implemented, while still wasted time maintaining the
offset-sorted tree of TRIM requests. Just remove the tree.
Remove locking from txg_all_lists_empty(). It is racy by design,
while 2 pair of locks/unlocks take noticeable time under the vdev
queue lock.
With these changes in my tests with volblocksize=4KB I measure vdev
queue lock spin time reduction by 50% on read and 75% on write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14925
It's been observed that in certain workloads (zvol-related being a
big one), ZFS will end up spending a large amount of time spinning
up taskqs only to tear them down again almost immediately, then
spin them up again...
I noticed this when I looked at what my mostly-idle system was doing
and wondered how on earth taskq creation/destroy was a bunch of time...
So I added a configurable delay to avoid it tearing down tasks the
first time it notices them idle, and the total number of threads at
steady state went up, but the amount of time being burned just
tearing down/turning up new ones almost vanished.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#14938
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
This is more-or-less like `zfs send`, but specifying the snapshot by its
objset id for situations where it can't be referenced any other way.
Sponsored-By: Klara, Inc.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: WHR <msl0000023508@gmail.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#14642
Make the section heading more generic (the section relates to ZFS files
as well as ZFS volumes).
Swapping to a ZFS volume is prone to deadlock. Remove the related
instruction, direct readers to OpenZFS FAQ. Related, but not linked
from within the manual page:
<https://openzfs.github.io/openzfs-docs/Project%20and%20Community/FAQ.html#using-a-zvol-for-a-swap-device-on-linux>
(Using a zvol for a swap device on Linux).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Graham Perrin <grahamperrin@freebsd.org>
Issue #7734Closes#14756
GRUB2 is compatible with all "read-only compatible" features,
so it is safe to add new features of this type to the grub2
compatibility list. We generally want to include all compatible
features, to minimize the differences between grub2-compatible
pools and no-compatibility pools.
Adding new properties `livelist` and `zpool_checkpoint` accordingly.
Also adding them to the man page which references this file as an
example, for consistency.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#14893
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
In case check_filesystem() does not error out and does not report
an error, remove that error block from error lists and logs
without requiring a scrub. This can happen when the original file and
all snapshots/clones referencing it have been removed.
Otherwise zpool status will still report that "Permanent errors have
been detected..." without actually reporting any of them.
To implement this change the functions introduced in corrective
receive were modified to take into account the head_errlog feature.
Before this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: Permanent errors have been detected in the following files:
=============================
After this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are
unaffected.
action: Determine if the device needs to be replaced, and clear the
errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-9P
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: No known data errors
=============================
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14813
For the head_errlog feature use dsl_dataset_hold_obj_flags() instead of
dsl_dataset_hold_obj() in order to enable access to the encryption keys
(if loaded). This enables reporting of errors in encrypted filesystems
which are not mounted but have their keys loaded.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14837
This commit expands on the zhack label repair command in d04b5c9 by
adding the -u option to undetach a device by regenerating uberblocks,
in addition to the existing functionality of fixing checksums, now
represented by -c. Previous behavior is retained in the case of no
options.
The changes are heavily inspired by Jeff Bonwick's labelfix
utility, as archived at:
https://gist.github.com/jjwhitney/baaa63144da89726e482
Additionally, it is now capable of properly determining the size of
block devices and other media, as well as handling sizes which are
not divisible by 2^18. This should make it viable for use on physical
devices and partitions, in addition to files.
These changes should make it possible to import zpools that have had
their uberblocks erased, such as in the case of pools rendered
inaccessible by erroneous detach commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: buzzingwires <buzzingwires@outlook.com>
Closes#14773
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
* Fixed one typo (effects -> affects)
* Re-worded raidz description to make it clearer that it is not
quite the same as RAID5, though similar
* Clarified that data is not necessarily written in a static
stripe width
* Minor grammar consistency improvement
* Noted that "volumes" means zvols
* Fixed a couple of split infinitives
* Clarified that hot spares come from the same pool they were
assigned to
* "we" -> ZFS
* Fixed warnings thrown by mandoc, and removed unnecessary
wordiness in one fixed line.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brandon Thetford <brandon@dodecatec.com>
Closes#14726
It was previously available only to FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: Seagate Technology LLC
Closes#14718
This had always worked in my testing, but a user on hardware reported
this to happen 100%, and I reproduced it once with cold VM host caches.
dracut-zfs-generator runs as a systemd generator, i.e. at Some
Relatively Early Time; if root= is a fixed dataset, it tries to
"solve [necessities] statically at generation time".
If by that point zfs-import.target hasn't popped (because the import is
taking a non-negligible amount of time for whatever reason), it'll see
no children for the root datase, and as such generate no mounts.
This has never had any right to work. No-one caught this earlier because
it's just that much more convenient to have root=zfs:AUTO, which orders
itself properly.
To fix this, always run zfs-nonroot-necessities.service;
this additionally simplifies the implementation by:
* making BOOTFS from zfs-env-bootfs.service be the real, canonical,
root dataset name, not just "whatever the first bootfs is",
and only set it if we're ZFS-booting
* zfs-{rollback,snapshot}-bootfs.service can use this instead of
re-implementing it
* having zfs-env-bootfs.service also set BOOTFSFLAGS
* this means the sysroot.mount drop-in can be fixed text
* zfs-nonroot-necessities.service can also be constant and always
enabled, because it's conditioned on BOOTFS being set
There is no longer any code generated at run-time
(the sysroot.mount drop-in is an unavoidable gratuitous cp).
The flow of BOOTFS{,FLAGS} from zfs-env-bootfs.service to sysroot.mount
is not noted explicitly in dracut.zfs(7), because (a) at some point it's
just visual noise and (b) it's already ordered via d-p-m.s from z-i.t.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#14690
Address the following bugs in persistent error log:
1) Check nested clones, eg "fs->snap->clone->snap2->clone2".
2) When deleting files containing error blocks in those clones (from
"clone" the example above), do not break the check chain.
3) When deleting files in the originating fs before syncing the errlog
to disk, do not break the check chain. This happens because at the
time of introducing the error block in the error list, we do not have
its birth txg and the head filesystem. If the original file is
deleted before the error list is synced to the error log (which is
when we actually lookup the birth txg and the head filesystem), then
we do not have access to this info anymore and break the check chain.
The most prominent change is related to achieving (3). We expand the
spa_error_entry_t structure to accommodate the newly introduced
zbookmark_err_phys_t structure (containing the birth txg of the error
block).Due to compatibility reasons we cannot remove the
zbookmark_phys_t structure and we also need to place the new structure
after se_avl, so it is not accounted for in avl_find(). Then we modify
spa_log_error() to also provide the birth txg of the error block. With
these changes in place we simplify the previously introduced function
get_head_and_birth_txg() (now named get_head_ds()).
We chose not to follow the same approach for the head filesystem (thus
completely removing get_head_ds()) to avoid introducing new lock
contentions.
The stack sizes of nested functions (as measured by checkstack.pl in the
linux kernel) are:
check_filesystem [zfs]: 272 (was 912)
check_clones [zfs]: 64
We also introduced two new tests covering the above changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14633
Use a bold header row and colorize the AVAIL column based on
the used space percentage of volume.
We define these colors:
- when > 80%, use yellow
- when > 90%, use red
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14350
Use a bold header and colorize the space suffixes in iostat
by order of magnitude like this:
- K is green
- M is yellow
- G is red
- T is lightblue
- P is magenta
- E is cyan
- 0 space is colored gray
Reviewed-by: WHR <msl0000023508@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14621Closes#14459
And bump all the values after it, matching the header update in
67a1b037.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14665
Fix the manpage. The "SYNOPSIS" section is incorrectly formatted for
receive -c. I also took this opportunity to reword some parts and
fix a run-on sentence in the manpage.
Add large block testing for corrective recv. This adds a new test
that makes sure blocks generated using zfs send -L/--large-block
large-block send flag are able to be used for healing.
Since with unloaded key and errlog feature enabled corruption is not
shown in zpool status #13675 is fixed the zfs_receive_corrective.ksh
test no longer sets -o feature@head_errlog=disabled on pool creation
so that it can also test for regressions related to head_errlog feature.
Note that the zfs_receive_compressed_corrective.ksh and
zfs_receive_large_block_corrective.ksh tests are still creating pools
with -o feature@head_errlog=disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#14615
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
Traditionally ARC adaptation was limited to MRU/MFU distribution. But
for years people with metadata-centric workload demanded mechanisms to
also manage data/metadata distribution, that in original ZFS was just
a FIFO. As result ZFS effectively got separate states for data and
metadata, minimum and maximum metadata limits etc, but it all required
manual tuning, was not adaptive and in its heart remained a bad FIFO.
This change removes most of existing eviction logic, rewriting it from
scratch. This makes MRU/MFU adaptation individual for data and meta-
data, same as the distribution between data and metadata themselves.
Since most of required states separation was already done, it only
required to make arcs_size state field specific per data/metadata.
The adaptation logic is still based on previous concept of ghost hits,
just now it balances ARC capacity between 4 states: MRU data, MRU
metadata, MFU data and MFU metadata. To simplify arc_c changes instead
of arc_p measured in bytes, this code uses 3 variable arc_meta, arc_pd
and arc_pm, representing ARC balance between metadata and data, MRU and
MFU for data, and MRU and MFU for metadata respectively as 32-bit fixed
point fractions. Since we care about the math result only when need to
evict, this moves all the logic from arc_adapt() to arc_evict(), that
reduces per-block overhead, since per-block operations are limited to
stats collection, now moved from arc_adapt() to arc_access() and using
cheaper wmsums. This also allows to remove ugly ARC_HDR_DO_ADAPT flag
from many places.
This change also removes number of metadata specific tunables, part of
which were actually not functioning correctly, since not all metadata
are equal and some (like L2ARC headers) are not really evictable.
Instead it introduced single opaque knob zfs_arc_meta_balance, tuning
ARC's reaction on ghost hits, allowing administrator give more or less
preference to metadata without setting strict limits.
Some of old code parts like arc_evict_meta() are just removed, because
since introduction of ABD ARC they really make no sense: only headers
referenced by small number of buffers are not evictable, and they are
really not evictable no matter what this code do. Instead just call
arc_prune_async() if too much metadata appear not evictable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14359
The approach is straightforward: for dataset ops, if a key was offered,
find the encryption root and the various encryption parameters, derive a
wrapping key if necessary, and then unlock the encryption root. After
that all the regular dataset ops will return unencrypted data, and
that's kinda the whole thing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#11551Closes#12707Closes#14503
A frequent misunderstanding is that zdb accesses the pool through the
kernel or filesystem, leading to confusion particularly when it can't
access something that it seems like it should be able to.
I've seen this confusion recently when zdb couldn't access a pool because
the user didn't have permission to read directly from the block devices,
and when it couldn't show attributes of encrypted files even though the
dataset was unlocked.
The manpage already speaks to another symptom of this, namely that zdb
may "behave erratically" on an active pool; here I'm trying to make that
a little more explicit.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#14539
Adding vdevprops.7 to the Makefile ensures that it gets installed
properly on FreeBSD.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Daniel Ebdrup Jensen <debdrup@FreeBSD.org>
Closes#14527
When testing distributed rebuild performance with more capable
hardware it was observed than increasing the zfs_rebuild_vdev_limit
to 64M reduced the rebuild time by 17%. Beyond 64MB there was
some improvement (~2%) but it was not significant when weighed
against the increased memory usage. Memory usage is capped at 1/4
of arc_c_max.
Additionally, vr_bytes_inflight_max has been moved so it's updated
per-metaslab to allow the size to be adjust while a rebuild is
running.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
For HDD based pools the default zfs_scan_vdev_limit of 4M
per-vdev can significantly limit the maximum scrub performance.
Increasing the default to 16M can double the scrub speed from
80 MB/s per disk to 160 MB/s per disk.
This does increase the memory footprint during scrub/resilver
but given the performance win this is a reasonable trade off.
Memory usage is capped at 1/4 of arc_c_max. Note that number
of outstanding I/Os has not changed and is still limited by
zfs_vdev_scrub_max_active.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14428
When resilvering the estimated time remaining is calculated using
the average issue rate over the current pass. Where the current
pass starts when a scan was started, or restarted, if the pool
was exported/imported.
For dRAID pools in particular this can result in wildly optimistic
estimates since the issue rate will be very high while scanning
when non-degraded regions of the pool are scanned. Once repair
I/O starts being issued performance drops to a realistic number
but the estimated performance is still significantly skewed.
To address this we redefine a pass such that it starts after a
scanning phase completes so the issue rate is more reflective of
recent performance. Additionally, the zfs_scan_report_txgs
module option can be set to reset the pass statistics more often.
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14410
Despite all optimizations, tests on actual hardware show that FreeBSD
kernel can't sleep for less then ~2us. Similar tests on Linux show
~50us delay at least from nanosleep() (haven't tested inside kernel).
It means that on very fast log device ZIL may not be able to satisfy
zfs_commit_timeout_pct block commit timeout, increasing log latency
more than desired.
Handle that by introduction of zil_min_commit_timeout parameter,
specifying minimal timeout value where additional delays to aggregate
writes may be skipped. Also skip delays if the LWB is more than 7/8
full, that often happens if I/O sizes are constant and match one of
LWB sizes. Both things are applied only if there were no already
outstanding log blocks, that may indicate single-threaded workload,
that by definition can not benefit from the commit delays.
While there, add short time moving average to zl_last_lwb_latency to
make it more stable.
Tests of single-threaded 4KB writes to NVDIMM SLOG on FreeBSD show IOPS
increase by 9% instead of expected 5%. For zfs_commit_timeout_pct of
1 there IOPS increase by 5.5% instead of expected 1%.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14418
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
It was changed in e99932f7de,
but without docs update.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#14400
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
This change turns `MZAP_MAX_BLKSZ` into a `ZFS_MODULE_PARAM()` called
`zap_micro_max_size`. As a result, we can experiment with different
micro ZAP sizes to improve directory size scaling.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Co-authored-by: Toomas Soome <toomas.soome@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14292
Recent ARC commits added new statistic counters, such as iohits,
uncached state, etc. Represent those. Also some of previously
reported numbers were confusing or even made no sense. Cleanup
and restructure existing reports.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14115
Issue #14123
Issue #14243Closes#14320
This saves 40 bytes per full ARC header, reducing it on FreeBSD from
240 to 200 bytes on production bits.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14315
This adds support to color zfs diff (in the style of git diff)
conditional on the ZFS_COLOR environment variable.
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14179
Correct new mandoc errors.
```
STYLE: input text line longer than 80 bytes
STYLE: no blank before trailing delimiter
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
As new compression algorithms are added to ZFS, it could be useful for
people to recompress data with new algorithms. There is currently no
mechanism to do this aside from copying the data manually into a new
filesystem with the new algorithm enabled. This tool allows the
transformation to happen through zfs send, allowing it to be done
efficiently to remote systems and in an incremental fashion.
A new zstream command is added that decompresses WRITE records and
then recompresses them with a provided algorithm, and then re-emits
the modified send stream. It may also be possible to re-compress
embedded block pointers, but that was not attempted for the initial
version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#14106
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
The quota for ZVOLs is set to the size of the volume. When the quota
reaches the maximum, there isn't an excellent way to check if the new
writers are overwriting the data or if they are inserting a new one.
Because of that, when we reach the maximum quota, we wait till txg is
flushed. This is causing a significant fluctuation in bandwidth.
In the case of ZVOL, the quota is enforced by the volsize, so we
can omit it.
This commit adds a sysctl thats allow to control if the quota mechanism
should be enforced or not.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13838
This allows for printing a machine-readable, accurate to the second,
hold creation time in the form of a unix epoch timestamp.
Additionally, updates relevant documentation and man pages accordingly.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mohamed Tawfik <m_tawfik@aucegypt.edu>
Closes#13690Closes#14152
Some of our customers have been occasionally hitting zfs import failures
in Linux because udevd doesn't create the by-id symbolic links in time
for zpool import to use them. The main issue is that the
systemd-udev-settle.service that zfs-import-cache.service and other
services depend on is racy. There is also an openzfs issue filed (see
https://github.com/openzfs/zfs/issues/10891) outlining the problem and
potential solutions.
With the proper solutions being significant in terms of complexity and
the priority of the issue being low for the time being, this patch
exposes `zfs_vdev_open_timeout_ms` as a tunable so people that are
experiencing this issue often can increase it as a workaround.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14133
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
If a record is uncompressed on-disk but the block pointer insists
otherwise, reading it will return EIO. This commit adds an "off" type
to the "zstream decompress" command. Using it will set the compression
field in a zfs stream to "off" without changing the record's data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alan Somers <asomers@FreeBSD.org>
Sponsored by: Axcient
Closes#13997
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
Alexander Motin
Rich Ercolani
Rob Norris
Graham Perrin
Colm
George Amanakis
Brian Behlendorf
buzzingwires
Allan Jude
rob-wing
наб
dodexahedron
Tino Reichardt
Rob N
Alek P
Pawel Jakub Dawidek
D. Ebdrup
George Melikov
Ameer Hamza
Mateusz Piotrowski
Mateusz Piotrowski
Ethan Coe-Renner
szubersk
Paul Dagnelie
Mariusz Zaborski
Mariusz Zaborski
Mohamed Tawfik
Serapheim Dimitropoulos
Akash B
Alan Somers
Richard Yao