It's not enough to preserve/restore MS_RDONLY on the superblock flags
to avoid remounting a snapshot read-write: be explicit about our
intentions to the VFS layer so the readonly bit is updated correctly
in do_remount_sb().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6510Closes#6515
The addition of the large_dnode_008_pos test case, which runs
right before this one, exposed some racy behavior in grow_pool
setup.sh on the Ubuntu kmemleak builder. Before creating
partitions on a device destroying any existing ones.
ERROR: set_partition 1 100mb loop0 exited 1
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6499Closes#6516
With HPE hardware and hpsa-driven SAS adapters, only a single phy is
reported, but no individual per-port phys (ie. no phy* entry below
port_dir), which breaks topology detection in the current sas_handler
code. Instead, slot information can be derived directly from the port
number. This change implements a new slot keyword "port" similar to
"id" and "lun", and assumes a default phy/port of 0 if no individual
phy entry can be found. It allows to use the "sas_direct" topology with
current HPE Dxxxx and Apollo 45xx JBODs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6484
When doing read on a file open with O_SYNC, it will trigger zil_commit.
However for snapshot, there's no zil, so we shouldn't be doing that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6478Closes#6494
If fault injection is enabled, the ZIO_FLAG_IO_RETRY could be set by
zio_handle_device_injection() to generate the FMA events and update
stats. Hence, ignore the flag and process such zios.
A better fix would be to add another flag in the zio_t to indicate that
the zio is failed because of a zinject rule. However, considering the
fact that we do this in debug bits, we could do with the crude check
using the global flag zio_injection_enabled which is set to 1 when
zinject records are added.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Closes#6383Closes#6384
* ztest.1 man page: fix typo
* zfs-module-parameters.5 man page: fix grammar
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#6492
Update the dbuf__evict__one() tracepoint so that it can safely
handle a NULL dmu_buf_impl_t pointer.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#6463
When performing concurrent object allocations using the new
multi-threaded allocator and large dnodes it's possible to
allocate overlapping large dnodes.
This case should have been handled by detecting an error
returned by dnode_hold_impl(). But that logic only checked
the returned dnp was not-NULL, and the dnp variable was not
reset to NULL when retrying. Resolve this issue by properly
checking the return value of dnode_hold_impl().
Additionally, it was possible that dnode_hold_impl() would
misreport a dnode as free when it was in fact in use. This
could occurs for two reasons:
* The per-slot zrl_lock must be held over the entire critical
section which includes the alloc/free until the new dnode
is assigned to children_dnodes. Additionally, all of the
zrl_lock's in the range must be held to protect moving
dnodes.
* The dn->dn_ot_type cannot be solely relied upon to check
the type. When allocating a new dnode its type will be
DMU_OT_NONE after dnode_create(). Only latter when
dnode_allocate() is called will it transition to the new
type. This means there's a window when allocating where
it can mistaken for a free dnode.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6414Closes#6439
Log contents of a receive record if an error occurs while writing
it out to the pool. This may help determine the cause when backup
streams are rejected as invalid.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6465
The vdev_id script requires awk, grep, and head. Use dracut_install to
ensure that these commands are available in the initrd environment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Karsten Kretschmer <kkretschmer@gmail.com>
Closes#6443Closes#6452
While investigating https://github.com/zfsonlinux/zfs/issues/6425 I
noticed that ioctl ZIOs were not setting zio->io_delay correctly. They
would set the start time in zio_vdev_io_start(), but never set the end
time in zio_vdev_io_done(), since ioctls skip it and go straight to
zio_done(). This was causing spurious "delayed IO" events to appear,
which would eventually get rate-limited and displayed as
"Missed events" messages in zed.
To get around the problem, this patch only sets zio->io_delay for read
and write ZIOs, since that's all we care about anyway.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6425Closes#6440
Use kstat to get a more accurate count of uberblock updates.
Using a loop with zdb can potentially miss some uberblocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6407Closes#6419
At import time spa_import() calls zvol_create_minors() directly: with
the current implementation we have no way to avoid device node
creation when volmode=none.
Fix this by enforcing volmode=none directly in zvol_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6426
Add aarch64 to the list of architecture which do not sanitize the
LDFLAGS from the environment. See fb963d33 for details.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6424
Test case zfs_send_007_pos regularly is killed
by test-runner during zfs-tests on buildbot. Disable
it for now until further investigation can be done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6422
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#6409Closes#6411
Redefine the SET_ERROR macro in terms of __dprintf() so the error
return codes get logged as both tracepoint events (if tracepoints are
enabled) and as ZFS debug log entries. This also allows us to use
the same definition of SET_ERROR() in kernel and user space.
Define a new debug flag ZFS_DEBUG_SET_ERROR=512 that may be bitwise
or'd into zfs_flags. Setting this flag enables both dprintf() and
SET_ERROR() messages in the debug log. That is, setting
ZFS_DEBUG_SET_ERROR and ZFS_DEBUG_DPRINTF|ZFS_DEBUG_SET_ERROR are
equivalent (this was done for sake of simplicity). Leaving
ZFS_DEBUG_SET_ERROR unset suppresses the SET_ERROR() messages which
helps avoid cluttering up the logs.
To enable SET_ERROR() logging, run:
echo 1 > /sys/module/zfs/parameters/zfs_dbgmsg_enable
echo 512 > /sys/module/zfs/parameters/zfs_flags
Remove the zfs_set_error_class tracepoints event class since
SET_ERROR() now uses __dprintf(). This sacrifices a bit of
granularity when selecting individual tracepoint events to enable but
it makes the code simpler.
Include file, function, and line number information in debug log
entries. The information is now added to the message buffer in
__dprintf() and as a result the zfs_dprintf_class tracepoints event
class was changed from a 4 parameter interface to a single parameter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6400
The userobj_accounting feature described in the zpool-features.5
man page was incorrectly indented. Fix it.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6402
Check in the DMU whether an object record in a send stream being
received contains an unsupported dnode slot count, and return an
error if it does. Failure to catch an unsupported dnode slot count
would result in a panic when the SPA attempts to increment the
reference count for the large_dnode feature and the pool has the
feature disabled. This is not normally an issue for a well-formed
send stream which would have the DMU_BACKUP_FEATURE_LARGE_DNODE flag
set if it contains large dnodes, so it will be rejected as
unsupported if the required feature is disabled. This change adds a
missing object record field validation.
Add missing stream feature flag checks in
dmu_recv_resume_begin_check().
Consolidate repetitive comment blocks in dmu_recv_begin_check().
Update zstreamdump to print the dnode slot count (dn_slots) for an
object record when running in verbose mode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6396
'zpool clear' should be able to resume I/O on suspended, but otherwise
healthy, pools.
4a283c7 accidentally introduced a new code path where we call
txg_wait_synced() on the suspended pool before we had the chance to
resume I/O via zio_resume(): this results in the 'zpool clear'
command hanging indefinitely, waiting for a TXG that cannot be synced.
Fix this by avoiding the call to txg_wait_synced().
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6399
The previous autoconf test for the presence of super_setup_bdi_name()
uses an invocation with an incorrect type signature, producing a
warning by the compiler when the test is run. This gets elevated to an
error when compiling with -Werror=format-security, causing autoconf to
falsely infer super_setup_bdi_name() is not present. This updates the
testing code to match the invocation used in
include/linux/vfs_compat.h.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Justin Bedo <cu@cua0.org>
Closes#6398
There is no need to perform the activity check before detecting that the
user must set the system hostid, because the pool's multihost property
is on, but spa_get_hostid() returned 0. The initial call to
vdev_uberblock_load() provided the information required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388
Add a callback to wake all running mmp threads when
zfs_multihost_interval is changed.
This is necessary when the interval is changed from a very large value
to a significantly lower one, while pools are imported that have the
multihost property enabled.
Without this commit, the mmp thread does not wake up and detect the new
interval until after it has waited the old multihost interval time. A
user monitoring mmp writes via the provided kstat would be led to
believe that the changed setting did not work.
Added a test in the ZTS under mmp to verify the new functionality is
working.
Added a test to ztest which starts and stops mmp threads, and calls into
the code to signal sleeping mmp threads, to test for deadlocks or
similar locking issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6387
"zhack feature stat" performs a read-only import, so the MMP activity
check is not necessary.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388Closes#6389
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
The config lock must be held for the duration of the MMP write.
Since the I/Os are executed via map_nowait(), the done function
is the only place where we know the write has completed.
Since SCL_STATE is taken as reader, overlapping I/Os do not
create a deadlock. The refcount is simply increased when new
I/Os are queued and decreased when I/Os complete.
Test case added which exercises the probe IO call path to
verify the fix and prevent a regression.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6394
This reverts commit cc9c6bc, which has been causing intermittent
test failures on buildbot. A correct fix for this locking issue
has been applied in a separate patch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
In zed event test cases, a brief delay was introduced
to allow for events to make it to the zed log. On at least
one buildbot builder, the 1 second delay is not long enough.
Therefore, increasing the delay should ensure the zed has
more than enough time to write to its log.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6395
If we're creating a pool with version >= SPA_VERSION_DSL_SCRUB (v11)
we need to account for additional space needed by the origin dataset
which will also be snapshotted: "poolname"+"/"+"$ORIGIN"+"@"+"$ORIGIN".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6374
When replacing a disk with non-wholedisk spare, we shouldn't zero_label
it. The wholedisk case already skip it. In fact, zero_label function
will fail saying device busy because it's already opened exclusively,
but since there's no error checking, the replace command will succeed,
causing great confusion.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6369
zpool iostat/status -c is supposed to be restricted
by its search path, but currently isn't. To prevent
arbitrary scripts from being executed, disallow '/'
from commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6353Closes#6359
Commit 379ca9c Multi-modifier protection (MMP) used HZ to convert
nanoseconds to ticks for use with cv_timedwait() and ddi_get_lbolt().
The correct macro is hz, which is defined within the SPL for kernel
space, and within zfs_context.h for user space.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6357Closes#6360
CID 165755: Division or modulo by zero (DIVIDE_BY_ZERO)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6352
Use log_must_busy when destroying the snapshot
and dataset during cleanup in zfs_mount_001_neg.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6382
This change allows mountpoint_003_pos and send-c_props
to run on Linux kernels that do not support mandatory
locking. Linux kernel versions greater than or equal to
4.4 no longer support mandatory locking and the test
suite will now account for that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6346Closes#6347Closes#6362
zvol_misc_002_pos was failing on Fedora 26 because its newer version
of fsck was returning a different code than previous versions. The
new fsck error code is valid and is been added to the test in this
patch.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6350
The zpool checkpoint feature in DxOS added a new field in the uberblock.
The Multi-Modifier Protection Pull Request from ZoL adds three new fields
in the uberblock (Reference: https://github.com/zfsonlinux/zfs/pull/6279).
As these two changes come from two different sources and once upstreamed
and deployed will introduce an incompatibility with each other we want
to upstream a change that will reserve the padding for both of them so
integration goes smoothly and everyone gets both features.
Porting Notes: Preserved MMP comments in uberblock struct.
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Olaf Faaland <faaland1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8491
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d84fa5fCloses#6390
Commit torvalds/linux@4e4cbee9. The bio->bi_error field was
replaced with bio->bi_status which is an enum that describes
all possible error types.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6351
- Use nested [] notation to denote optional script list elements
- Fix space before comma after smarctl(8)
- Fix typo and formatting error in reference to -v option
- Fix spelling errors
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6370
CID 165757: Control flow issues (MISSING_BREAK)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#6348
When an IO fails then zio_vdev_io_done() can call vdev_probe()
to determine the health of the vdev. This is safe as long as
the original zio was submitted with zio_wait() and holds the
SCL_STATE_ALL lock over the operation.
If zio_no_wait() was used then the done callback will submit
the probe IO outside the SCL_STATE_ALL lock and hit this
ASSERT in zio_create()
ASSERT(!vd || spa_config_held(spa, SCL_STATE_ALL, RW_READER));
Resolve the issue by only allowing vdev_probe() to be called
when there's a waiter indicating the caller is using zio_wait().
This assumes that caller is still holding SCL_STATE_ALL.
This issue isn't MMP specific but was surfaced when testing.
Without this patch it can be reproduced by running:
zpool set multihost on <pool>
zinject -d <vdev> -e io -T write -f 50 <pool> -L uber
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#745Closes#6279
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
If no spl_hostid was set, and no /etc/hostid file existed, the user
and kernel would have different values for the hostid.
The kernel's would be 0. User space's would depend on the libc
implementation. On systems with glibc, it would be a generated value,
probably the first 4 bytes of an IP address (see man 3 gethostid and
comments above hostid_read in SPL for details).
This then causes the hostid stored in the labels and in the pool
config not to match the hostid userspace obtains from
get_system_hostid().
Since the kernel has no way to know the libc's generated hostid value,
it serves no purpose for ZFS to use the value.
This patch changes user space's get_system_hostid() to conform to the
kernel's method, first checking for the spl_hostid via sysfs, and then
reading from /etc/hostid directly.
It does not look up spl_hostid_path, because if that is set and the
file it pointed to exists, spl_hostid will reflect its contents.
It eliminates the call to libc's gethostid().
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Authored by: Dave Eddy <dave@daveeddy.com>
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Joshua M. Clulow <jmc@joyent.com>
Reviewed by: Josh Wilsdon <jwilsdon@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Alan Somers <asomers@gmail.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6939
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ce1577bCloses#6328
When VERIFY3_IMPL() was adjusted in 682ce104, the values of
the operands were omitted from the variadic arguments list.
This patch simply corrects this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6343
The volmode property may be set to control the visibility of ZVOL
block devices.
This allow switching ZVOL between three modes:
full - existing fully functional behaviour (default)
dev - hide partitions on ZVOL block devices
none - not exposing volumes outside ZFS
Additionally the new zvol_volmode module parameter can be used to
control the default behaviour.
This functionality can be used, for instance, on "backup" pools to
avoid cluttering /dev with unneeded zd* devices.
Original-patch-by: mav <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
FreeBSD-commit: https://github.com/freebsd/freebsd/commit/dd28e6bbCloses#1796Closes#3438Closes#6233
LOLi
Brian Behlendorf
sckobras
Chunwei Chen
sanjeevbagewadi
Fabian-Gruenbichler
gaurkuma
Tony Hutter
Ned Bass
Karsten Kretschmer
Giuseppe Di Natale
bunder2015
Justin Bedő
Olaf Faaland
Serapheim Dimitropoulos
George Melikov
Dave Eddy
Tom Caputi