While unlikely it is possible for dsl_destroy_head() to return
ENOSPC in the ztest_objset_destroy_cb(). This can occur even
when ZFS_SPACE_CHECK_DESTROY is used with the dsl_sync_task().
Both the existence of a checkpoint and pending deferred frees
can cause this.
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8206
As a result of the changes made in 8585, it's possible for an excessive
amount of vdev flush commands to be issued under some workloads.
Specifically, when the workload consists of mostly async write activity,
interspersed with some sync write and/or fsync activity, we can end up
issuing more flush commands to the underlying storage than is actually
necessary. As a result of these flush commands, the write latency and
overall throughput of the pool can be poorly impacted (latency
increases, throughput decreases).
Currently, any time an lwb completes, the vdev(s) written to as a result
of that lwb will be issued a flush command. The intenion is so the data
written to that vdev is on stable storage, prior to communicating to any
waiting threads that their data is safe on disk.
The problem with this scheme, is that sometimes an lwb will not have any
threads waiting for it to complete. This can occur when there's async
activity that gets "converted" to sync requests, as a result of calling
the zil_async_to_sync() function via zil_commit_impl(). When this
occurs, the current code may issue many lwbs that don't have waiters
associated with them, resulting in many flush commands, potentially to
the same vdev(s).
For example, given a pool with a single vdev, and a single fsync() call
that results in 10 lwbs being written out (e.g. due to other async
writes), that will result in 10 flush commands to that single vdev (a
flush issued after each lwb write completes). Ideally, we'd only issue a
single flush command to that vdev, after all 10 lwb writes completed.
Further, and most important as it pertains to this change, since the
flush commands are often very impactful to the performance of the pool's
underlying storage, unnecessarily issuing these flush commands can
poorly impact the performance of the lwb writes themselves. Thus, we
need to avoid issuing flush commands when possible, in order to acheive
the best possible performance out of the pool's underlying storage.
This change attempts to address this problem by changing the ZIL's logic
to only issue a vdev flush command when it detects an lwb that has a
thread waiting for it to complete. When an lwb does not have threads
waiting for it, the responsibility of issuing the flush command to the
vdevs involved with that lwb's write is passed on to the "next" lwb.
It's only once a write for an lwb with waiters completes, do we issue
the vdev flush command(s). As a result, now when we issue the flush(s),
we will issue them to the vdevs involved with that specific lwb's write,
but potentially also to vdevs involved with "previous" lwb writes (i.e.
if the previous lwbs did not have waiters associated with them).
Thus, in our prior example with 10 lwbs, it's only once the last lwb
completes (which will be the lwb containing the waiter for the thread
that called fsync) will we issue the vdev flush command; all of the
other lwbs will find they have no waiters, so they'll pass the
responsibility of the flush to the "next" lwb (until reaching the last
lwb that has the waiter).
Porting Notes:
* Reconciled conflicts with the fastwrite feature.
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Ported-by: Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9962
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/545190c6Closes#8188
This one line patch moves an assert in the function dump_dir()
below an error check that ensures it ran correctly. This ensures
zdb dumps the error that actually caused the problem, as opposed
to one of its symptoms.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8171
The verbose output of 'zpool list' was not correctly aligned due
to differences in the vdev name lengths. Minimally update the
code the correct the alignment using the same strategy employed
by 'zpool status'.
Missing dashes were added for the empty defaults columns, and
the vdev state is now printed for all vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7308Closes#8147
This patch fixes a small race condition in ztest_zil_remount()
that could result in a deadlock. ztest_device_removal() calls
spa_vdev_remove() which may eventually call spa_reset_logs().
If ztest_zil_remount() attempts to call zil_close() while this
is happening, it may fail when it asserts !zilog_is_dirty(zilog).
This patch simply adds locking to correct the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8154
This commit fixes the following ASSERT in zfs_receive_one() when
receiving a send stream from a root dataset with the "-e" option:
$ sudo zfs snap source@snap
$ sudo zfs send source@snap | sudo zfs recv -e destination/recv
chopprefix > drrb->drr_toname
ASSERT at libzfs_sendrecv.c:3804:zfs_receive_one()
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8121
ztest currently uses the boolean flag ztest_device_removal_active
to protect some tests that may not run successfully if they occur
at the same time as ztest_device_removal(). Unfortunately, in the
event that ztest is in the middle of a device removal when it
decides to issue a SIGKILL, the device removal will be
automatically restarted (without setting the flag) when the pool
is re-imported on the next run. This patch corrects this by
ensuring that any in-progress removals are completed before running
further tests after the re-import.
This patch also makes a few small changes to prevent race conditions
involving the creation and destruction of spa->spa_vdev_removal,
since this field is not protected by any locks. Some checks that
may run concurrently with setting / unsetting this field have been
updated to check spa->spa_removing_phys.sr_state instead. The most
significant change here is that spa_removal_get_stats() no longer
accounts for in-flight work done, since that could result in a NULL
pointer dereference.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8105
This change allows 'zpool split' to work with whole-disk devices and
updates the ZFS Test Suite with a new script to exercise this
functionality.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6643Closes#8133
Porting Notes:
* Use thread pools (tpool) API instead of introducing taskq interfaces
to libzfs.
* Use pthread_mutext for locks as mutex_t isn't available.
* Ignore alternative libshare initialization since OpenZFS-7955 is
not present on zfsonlinux.
Authored by: Sebastien Roy <seb@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Authored by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Don Brady <don.brady@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8115
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a3f0e2b569Closes#8092
This commit adds a new test case to the ZFS Test Suite to verify ZED
can detect when a device is physically removed from a running system:
the device will be offlined if a spare is not available in the pool.
We implement this by using the existing libudev functionality and
without relying solely on the FM kernel module capabilities which have
been observed to be unreliable with some kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1537Closes#7926
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
ztest occasionally hits an assert that !zilog_is_dirty() during
zil_close(). This is caused by an interaction between 2 threads.
First, ztest_run() waits for each test thread to complete and
closes the associated dataset as soon as the thread joins. At
the same time, the ztest_vdev_add_remove() test may attempt to
remove the slog, which will open, dirty, and reset the logs on
every dataset in the pool (including those of other threads).
This patch simply ensures that we always join all of the test
threads before closing any datasets.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8094
This patch ensures that logs are replayed on all datasets prior
to starting ztest workers. This ensures that the call to
vdev_offline() a log device in ztest_fault_inject() will not fail
due to the log device being required for replay.
This patch also fixes a small issue found during testing where
spa_keystore_load_wkey() does not check that the dataset specified
is an encryption root. This check was present in libzfs, however.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8084
In order to validate the gang block code ztest is configured to
artificially force a fraction of large blocks to be written as
gang blocks. The default setting chosen for this was to
write 25% of all blocks 32k or larger using gang blocks.
The confluence of an unrealistically large number of gang blocks,
the aggressive fault injection done by ztest, and the split
segment reconstruction logic introduced by device removal has
resulted in the following type of failure:
zdb -bccsv -G -d ... exit code 3
Specifically, zdb was unable to open the pool because it was
unable to reconstruct a damaged block. Manual investigation
of multiple failures clearly showed that the block could be
reconstructed. However, due to the large number of damaged
segments (>35) it could not be done in the allotted time.
Furthermore, the large number of gang blocks was determined
to be the reason for the unrealistically large number of
damaged segments. In order to make this situation less
likely, this change both increases the forced gang block
size to 64k and reduces the frequency to 3% of blocks.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8080
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
This minor bug was introduced with the port of the feature from
OpenZFS to ZoL. This patch fixes the issue that was caused by
a minor re-ordering from the original code.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8001
The root cause of these failures is that udev can notify the
ZED of newly created partition before its links are created.
Handle this by allowing an auto-replace to briefly wait until
udev confirms the links exist.
Distill this test case down to its essentials so it can be run
reliably. What we need to check is that:
1) A new disk, in the same physical location, is automatically
brought online when added to the system,
2) It completes the replacement process, and
3) The pool is now ONLINE and healthy.
There is no need to remove the scsi_debug module. After exporting
the pool the disk can be zeroed, removed, and then re-added to the
system as a new disk.
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8051
From, https://lintlyci.github.io/Flake8Rules/rules/W605.html
As of Python 3.6, a backslash-character pair that is not a valid
escape sequence now generates a DeprecationWarning. Although this
will eventually become a SyntaxError, that will not be for several
Python releases.
Note 'float_pobj' was simply removed from arcstat.py since it
was entirely unused.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8056
spa->spa_vdev_removal is created in a sync task that is initiated
via dsl_sync_task_nowait(). Since the task may not run before
spa_vdev_remove() returns, we must wait at least 1 txg to ensure
that the removal struct has been created.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8010
This patch fixes an issue where ztest's deadman thread would
trigger a panic because reconstructing artifically damaged
blocks would take too long to reconstruct. This patch simply
limits how often ztest inflicts split-block damage and how
many segments it can damage when it does.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8010
This patch resolves a problem where the -G option in both zdb and
ztest would cause the code to call __dprintf() to print zfs_dbgmsg
output. This function was not properly wired to add messages to the
dbgmsg log as it is in userspace and so the messages were simply
dropped. This patch also tries to add some degree of distinction to
dprintf() (which now prints directly to stdout) and zfs_dbgmsg()
(which adds messages to an internal list that can be dumped with
zfs_dbgmsg_print()).
In addition, this patch corrects an issue where ztest used a global
variable to decide whether to dump the dbgmsg buffer on a crash.
This did not work because ztest spins up more instances of itself
using execv(), which did not copy the global variable to the new
process. The option has been moved to the ztest_shared_opts_t
which already exists for interprocess communication.
This patch also changes zfs_dbgmsg_print() to use write() calls
instead of printf() so that it will not fail when used in a signal
handler.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8010
The zloop test has been failing in buildbot for the last few weeks
with various failures in ztest_deadman_thread(). This is due to the
fact that this thread is not stopped when performing pool import /
export tests as it should be. This patch simply corrects this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8010
Currently, if a resilver is triggered for any reason while an
existing one is running, zfs will immediately restart the existing
resilver from the beginning to include the new drive. This causes
problems for system administrators when a drive fails while another
is already resilvering. In this case, the optimal thing to do to
reduce risk of data loss is to wait for the current resilver to end
before immediately replacing the second failed drive, which allows
the system to operate with two incomplete drives for the minimum
amount of time.
This patch introduces the resilver_defer feature that essentially
does this for the admin without forcing them to wait and monitor
the resilver manually. The change requires an on-disk feature
since we must mark drives that are part of a deferred resilver in
the vdev config to ensure that we do not assume they are done
resilvering when an existing resilver completes.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: @mmaybee
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7732
ZFS allows, by default, sharing of spare devices among different pools;
this commit simply restores this functionality for disk devices and
adds an additional tests case to the ZFS Test Suite to prevent future
regression.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7999
The boolean featureflags in use thus far in ZFS are extremely useful,
but because they take advantage of the zap layer, more interesting data
than just a true/false value can be stored in a featureflag. In redacted
send/receive, this is used to store the list of redaction snapshots for
a redacted dataset.
This change adds the ability for ZFS to store types other than a boolean
in a featureflag. The only other implemented type is a uint64_t array.
It also modifies the interfaces around dataset features to accomodate
the new capabilities, and adds a few new functions to increase
encapsulation.
This functionality will be used by the Redacted Send/Receive feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7981
OpenZFS 9847 - leaking dd_clones (DMU_OT_DSL_CLONES) objects
We're leaking the dd_clones objects in dsl_dir_destroy_sync. This bug
appears to have been around forever. Thankfully the amount of space
typically involved is tiny.
In addition this adds a mechanism in ZDB to find objects in the MOS
which are leaked (not referenced anywhere).
Porting notes:
* Added dd_crypto_obj to ZDB MOS object leak tracking
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
OpenZFS-issue: https://illumos.org/issues/9847Closes#7979
The vdev_checkpoint_sm_object(), vdev_obsolete_sm_object(), and
vdev_obsolete_counts_are_precise() functions assume that the
only way a zap_lookup() can fail is if the requested entry is
missing. While this is the most common cause, it's not the only
cause. Attemping to access a damaged ZAP will result in other
errors.
The most likely scenario for accessing a damaged ZAP is during
an extreme rewind pool import. Under these conditions the pool
is expected to contain damaged objects and the import code was
updated to handle this gracefully. Getting an ECKSUM error from
these ZAPs after the pool in import a far less likely, therefore
the behavior for call paths was not modified.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7809Closes#7921
The ZFS range locking code in zfs_rlock.c/h depends on ZPL-specific
data structures, specifically znode_t. However, it's also used by
the ZVOL code, which uses a "dummy" znode_t to pass to the range
locking code.
We should clean this up so that the range locking code is generic
and can be used equally by ZPL and ZVOL, and also can be used by
future consumers that may need to run in userland (libzpool) as
well as the kernel.
Porting notes:
* Added missing sys/avl.h include to sys/zfs_rlock.h.
* Removed 'dbuf is within the locked range' ASSERTs from dmu_sync().
This was needed because ztest does not yet use a locked_range_t.
* Removed "Approved by:" tag requirement from OpenZFS commit
check to prevent needless warnings when integrating changes
which has not been merged to illumos.
* Reverted free_list range lock changes which were originally
needed to defer the cv_destroy() which was called immediately
after cv_broadcast(). With d2733258 this should be safe but
if not we may need to reintroduce this logic.
* Reverts: The following two commits were reverted and squashed in
to this change in order to make it easier to apply OpenZFS 9689.
- d88895a0, which removed the dummy znode from zvol_state
- e3a07cd0, which updated ztest to use range locks
* Preserved optimized rangelock comparison function. Preserved the
rangelock free list. The cv_destroy() function will block waiting
for all processes in cv_wait() to be scheduled and drop their
reference. This is done to ensure it's safe to free the condition
variable. However, blocking while holding the rl->rl_lock mutex
can result in a deadlock on Linux. A free list is introduced to
defer the cv_destroy() and kmem_free() until after the mutex is
released.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9689
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/680
External-issue: DLPX-58662
Closes#7980
Historically, zpool status prints "(repairing)" for any drives that
have errors during a scrub:
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
/tmp/file1 ONLINE 13 0 0 (repairing)
/tmp/file2 ONLINE 0 0 0
/tmp/file3 ONLINE 0 0 0
This was accidentally broken in "OpenZFS 9166 - zfs storage pool
checkpoint" (d2734cc). This patch adds it back in.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7779Closes#7978
Since native ZFS encryption was merged, we have been fighting
against a series of bugs that come down to the same problem: Key
mappings (which must be present during all I/O operations) are
created and destroyed based on dataset ownership, but I/Os can
have traditionally been allowed to "leak" into the next txg after
the dataset is disowned.
In the past we have attempted to solve this problem by trying to
ensure that datasets are disowned ater all I/O is finished by
calling txg_wait_synced(), but we have repeatedly found edge cases
that need to be squashed and code paths that might incur a high
number of txg syncs. This patch attempts to resolve this issue
differently, by adding a reference to the key mapping for each txg
it is dirtied in. By doing so, we can remove many of the
unnecessary calls to txg_wait_synced() we have added in the past
and ensure we don't need to deal with this problem in the future.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7949
Recent changes in the Linux kernel made it necessary to prefix
the refcount_add() function with zfs_ due to a name collision.
To bring the other functions in line with that and to avoid future
collisions, prefix the other refcount functions as well.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Closes#7963
Due to a flaw in 4589f3ae the number of unique combinations
could be calculated incorrectly. This could result in the
random combinations reconstruction being used when it would
have been possible to check all combinations.
This change fixes the unique combinations calculation and
simplifies the reconstruction logic by maintaining a per-
segment list of unique copies.
The vdev_indirect_splits_damage() function was introduced
to validate both the enumeration and random reconstruction
logic with ztest. It is implemented such it will never
make a known recoverable block unrecoverable.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6900Closes#7934
torvalds/linux@59b57717f ("blkcg: delay blkg destruction until
after writeback has finished") added a refcount_t to the blkcg
structure. Due to the refcount_t compatibility code, zfs_refcount_t
was used by mistake.
Resolve this by removing the compatibility code and replacing the
occurrences of refcount_t with zfs_refcount_t.
Reviewed-by: Franz Pletz <fpletz@fnordicwalking.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Schumacher <timschumi@gmx.de>
Closes#7885Closes#7932
Bandwidth and iops are average per second while *_wait are averages
per request for latency or, for queue depths, an instantaneous
measurement at the end of an interval (according to man zpool).
When calculating the first two it makes sense to do
x/interval_duration (x being the increase in total bytes or number of
requests over the duration of the interval, interval_duration in
seconds) to 'scale' from amount/interval_duration to amount/second.
But applying the same math for the latter (*_wait latencies/queue) is
wrong as there is no interval_duration component in the values (these
are time/requests to get to average_time/request or already an
absulute number).
This bug leads to the only correct continuous *_wait figures for both
latencies and queue depths from 'zpool iostat -l/q' being with
duration=1 as then the wrong math cancels itself (x/1 is a nop).
This removes temporal scaling from latency and queue depth figures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregor Kopka <gregor@kopka.net>
Closes#7945Closes#7694
This change prevents zstreamdump from crashing when trying to print
invalid nvlist data (DRR_BEGIN record) from a truncated send stream.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7917
This change improve the handling of invalid filesystem properties when
specified at pool creation: this is useful when 'zpool create -n'
(dry run) is executed to detect invalid fs-level options (-O) before
the actual command is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7620Closes#7878
When no permission set is defined for a dataset the create time
permissions are incorrectly shown as if they were a permission set.
This change simply correct how allow permissions are displayed.
This commit also fixes a small manpage formatting issue and adds the
"zfs_allow_003_pos" test case to the ZFS Test Suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7519Closes#7860
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
We want newer versions of libzfs_core to run against an existing
zfs kernel module (i.e. a deferred reboot or module reload after
an update).
Programmatically document, via a zfs_ioc_key_t, the valid arguments
for the ioc commands that rely on nvpair input arguments (i.e. non
legacy commands from libzfs_core). Automatically verify the expected
pairs before dispatching a command.
This initial phase focuses on the non-legacy ioctls. A follow-on
change can address the legacy ioctl input from the zfs_cmd_t.
The zfs_ioc_key_t for zfs_keys_channel_program looks like:
static const zfs_ioc_key_t zfs_keys_channel_program[] = {
{"program", DATA_TYPE_STRING, 0},
{"arg", DATA_TYPE_UNKNOWN, 0},
{"sync", DATA_TYPE_BOOLEAN_VALUE, ZK_OPTIONAL},
{"instrlimit", DATA_TYPE_UINT64, ZK_OPTIONAL},
{"memlimit", DATA_TYPE_UINT64, ZK_OPTIONAL},
};
Introduce four input errors to identify specific input failures
(in addition to generic argument value errors like EINVAL, ERANGE,
EBADF, and E2BIG).
ZFS_ERR_IOC_CMD_UNAVAIL the ioctl number is not supported by kernel
ZFS_ERR_IOC_ARG_UNAVAIL an input argument is not supported by kernel
ZFS_ERR_IOC_ARG_REQUIRED a required input argument is missing
ZFS_ERR_IOC_ARG_BADTYPE an input argument has an invalid type
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7780
Removing hardcoded paths in many scripts.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bernie1995 <bernie.pikes@gmail.com>
Issue #7507Closes#7843
Assertion failed in arc_buf_destroy() when concurrently reading
block with checksum error.
Porting notes:
* The ability to zinject decompression errors has been added, but
this only works at the zio_decompress() level, where we have all
of the info we need to match against the user's zinject options.
* The decompress_fault test has been added to test the new zinject
functionality
* We attempted to set zio_decompress_fail_fraction to (1 << 18) in
ztest for further test coverage. Although this did uncover a few
low priority issues, this unfortuantely also causes ztest to
ASSERT in many locations where the code is working correctly since
it is designed to fail on IO errors. Developers can manually set
this variable with the '-o' option to find and debug issues.
Authored by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Tom Caputi <tcaputi@datto.com>
OpenZFS-issue: https://illumos.org/issues/9403
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/fa98e487a9Closes#7822
Since zdb opens the pools read-only, it cannot damage the pool in the
event the pool is already imported either on the same host or on
another one.
If the pool vdev structure is changing while zdb is importing the
pool, it may cause zdb to crash. However this is unlikely, and in any
case it's a user space process and can simply be run again.
For this reason, zdb should disable the multihost activity test on
import that is normally run.
This commit fixes a few zdb code paths where that had been overlooked.
It also adds tests to ensure that several common use cases handle this
properly in the future.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Gu Zheng <guzheng2331314@163.com>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7797Closes#7801
argv[] gets modified during string parsing for input arguments. This
is reflected in the live process listing. Don't do that.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7760
This change simply documents the existing "scripted mode" option in
both command help and man page.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7798
This change allows the arcstat.py script to handle unsupported options
gracefully and print both error and usage messages when one such option
is provided.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7799
When running ztest, never suspend the pool due to failed or delayed
MMP writes.
There are many sources of long delays within ztest, such as device
opens, closes, etc. which in combination, may delay MMP writes too
long and cause MMP to suspend the pool.
Some of these delays also affect real pools, and should be fixed.
That is being worked separately.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7776
- Add two new module parameters to icp (icp_aes_impl, icp_gcm_impl)
that control the crypto implementation. At the moment there is a
choice between generic and aesni (on platforms that support it).
- This enables support for AES-NI and PCLMULQDQ-NI on AMD Family
15h (bulldozer) and newer CPUs (zen).
- Modify aes_key_t to track what implementation it was generated
with as key schedules generated with various implementations
are not necessarily interchangable.
Reviewed by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Nathaniel R. Lewis <linux.robotdude@gmail.com>
Closes#7102Closes#7103
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
When running zdb without additional arguments against a pool containing
a checkpoint the entire checkpoint spacemap should not be dumped. Make
this behavior conditional upon passing the -mmmm option as described in
the zdb(8) man page.
-mmmm Display every spacemap record.
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7702
Add a default 4 KiB ashift for Amazon EC2 NVMe devices on instances with
NVMe ephemeral devices, such as the types c5d, f1, i3 and m5d.
As per the official documentation [1] a 4096 byte blocksize should be
used to match the underlying hardware.
The string was identified via:
$ sudo sginfo -M /dev/nvme0n1
INQUIRY response (cmd: 0x12)
----------------------------
Device Type 0
Vendor: NVMe
Product: Amazon EC2 NVMe
Revision level:
$ lsblk -io KNAME,TYPE,SIZE,MODEL
KNAME TYPE SIZE MODEL
nvme0n1 disk 442.4G Amazon EC2 NVMe Instance Storage
[1] https://docs.aws.amazon.com/AWSEC2/latest/UserGuide/
storage-optimized-instances.html
Retrived 2018-07-03
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Troels Nørgaard <tnn@tradeshift.com>
Closes#7676
Motivation
==========
The current space map encoding has the following disadvantages:
[1] Assuming 512 sector size each entry can represent at most 16MB for a segment.
This makes the encoding very inefficient for large regions of space.
[2] As vdev-wide space maps have started to be used by new features (i.e.
device removal, zpool checkpoint) we've started imposing limits in the
vdevs that can be used with them based on the maximum addressable offset
(currently 64PB for a top-level vdev).
New encoding
============
The layout can be found at space_map.h and it remains backwards compatible with
the old one. The introduced two-word entry format, besides extending the limits
imposed by the single-entry layout, also includes a vdev field and some extra
padding after its prefix.
The extra padding after the prefix should is reserved for future usage (e.g.
new prefixes for future encodings or new fields for flags). The new vdev field
not only makes the space maps more self-descriptive, but also opens the doors
for pool-wide space maps (expected to be used in the log spacemap project).
One final important note is that the number of bits used for vdevs is reduced
to 24 bits for blkptrs. That was decided as we don't know of any setups that
use more than 16M vdevs for the time being and we wanted to fit the vdev field
in the space map. In addition that gives us some extra bits in dva_t.
Other references:
=================
The new encoding is also discussed towards the end of the Log Space Map
presentation from 2017's OpenZFS summit.
Link: https://www.youtube.com/watch?v=jj2IxRkl5bQ
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/90a56e6d
OpenZFS-issue: https://www.illumos.org/issues/9238Closes#7665
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
This patch adds tunables for modifying the maximum memory limit and
maximum instruction limit that can be specified when running a channel
program.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
External-issue: LX-1085
Closes#7618
Commit 2ffd89fc allowed two new errors to be reported by zil_reset()
in order to provide a descriptive error message regarding why a log
device could not be removed. However, the new return values were
not handled in the ztest_vdev_add_remove() test case resulting in
ztest failures during automated testing.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7630
zpool and zed place scripts in subdirectories of libexecdir. Some
distributions locate architecture independent scripts in other locations
(e.g. Debian). To avoid these paths getting out of sync, centralize the
definitions.
Build zfs-test's default.cfg by Makefile. Use the new directory
logic building tests/zfs-tests/include/default.cfg.in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7597
Currently, during a recursive zfs destroy the first error that is
encountered will stop the destruction of the datasets. Errors may
happen for a variety of reasons including competing deletions
and busy datasets.
This patch switches recursive destroy to always do a best-effort
recursive dataset destroy.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7574
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
The only remaining consumer of the rwlock compatibility wrappers
is ztest. Remove the wrappers and convert the few remaining
calls to the underlying pthread functions.
rwlock_init() -> pthread_rwlock_init()
rwlock_destroy() -> pthread_rwlock_destroy()
rw_rdlock() -> pthread_rwlock_rdlock()
rw_wrlock() -> pthread_rwlock_wrlock()
rw_unlock() -> pthread_rwlock_unlock()
Note pthread_rwlock_init() defaults to PTHREAD_PROCESS_PRIVATE
which is equivilant to the USYNC_THREAD behavior. There is no
functional change.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7591
We want to be able to pass various settings during import/open of a
pool, which are not only related to rewind. Instead of adding a new
policy and duplicate a bunch of code, we should just rename
rewind_policy to a more generic term like load_policy.
For instance, we'd like to set spa->spa_import_flags from the nvlist,
rather from a flags parameter passed to spa_import as in some cases we
want those flags not only for the import case, but also for the open
case. One such flag could be ZFS_IMPORT_MISSING_LOG (as used in zdb)
which would allow zfs to open a pool when logs are missing.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9235
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d2b1e44Closes#7532
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7556
16MB alloc in zdb_embedded_block() can cause cores in certain
situations (clang, gcc55).
Authored by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
* Replaces an equivalent fix previously made for Linux.
OpenZFS-issue: https://illumos.org/issues/9523
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2c1964aCloses#7561
lib/libzfs/libzfs_mount.c:zfs_add_options provides the canonical
mount options used by a `zfs mount` command. Because we cannot call
`zfs mount` directly from a systemd.mount unit, we mirror that logic
in zfs-mount-generator.
The zed script is updated to cache these properties as well.
Include a mini-tutorial in the manual page, properly substitute
configuration paths in zfs-mount-generator.8.in, and standardize the
Makefile.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7453
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
Currently `zdb` consistently fails to examine non-idle pools as it
fails during the `spa_load()` process. The main problem seems to be
that `spa_load_verify()` fails as can be seen below:
$ sudo zdb -d -G dcenter
zdb: can't open 'dcenter': I/O error
ZFS_DBGMSG(zdb):
spa_open_common: opening dcenter
spa_load(dcenter): LOADING
disk vdev '/dev/dsk/c4t11d0s0': best uberblock found for spa dcenter. txg 40824950
spa_load(dcenter): using uberblock with txg=40824950
spa_load(dcenter): UNLOADING
spa_load(dcenter): RELOADING
spa_load(dcenter): LOADING
disk vdev '/dev/dsk/c3t10d0s0': best uberblock found for spa dcenter. txg 40824952
spa_load(dcenter): using uberblock with txg=40824952
spa_load(dcenter): FAILED: spa_load_verify failed [error=5]
spa_load(dcenter): UNLOADING
This change makes `spa_load_verify()` a dryrun when ran from
`zdb`. This is done by creating a global flag in zfs and then setting
it in `zdb`.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/8962
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/180ad792Closes#7459
9421 zdb should detect and print out the number of "leaked" objects
9422 zfs diff and zdb should explicitly mark objects that are on
the deleted queue
It is possible for zfs to "leak" objects in such a way that they are not
freed, but are also not accessible via the POSIX interface. As the only
way to know that this is happened is to see one of them directly in a
zdb run, or by noting unaccounted space usage, zdb should be enhanced to
count these objects and return failure if some are detected.
We have access to the delete queue through the zfs_get_deleteq function;
we should call it in dump_znode to determine if the object is on the
delete queue. This is not the most efficient possible method, but it is
the simplest to implement, and should suffice for the common case where
there few objects on the delete queue.
Also zfs diff and zdb currently traverse every single dnode in a dataset
and tries to figure out the path of the object by following it's parent.
When an object is placed on the delete queue, for all practical purposes
it's already discarded, it's parent might not exist anymore, and another
object might now have the object number that belonged to the parent.
While all of the above makes sense, when trying to figure out the path
of an object that is on the delete queue, we can run into issues where
either it is impossible to determine the path because the parent is
gone, or another dnode has taken it's place and thus we are returned a
wrong path.
We should therefore avoid trying to determine the path of an object on
the delete queue and mark the object itself as being on the delete queue
to avoid confusion. To achieve this, we currently have two ideas:
1. When putting an object on the delete queue, change it's parent object
number to a known constant that means NULL.
2. When displaying objects, first check if it is present on the delete
queue.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9421
OpenZFS-issue: https://illumos.org/issues/9422
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45ae0dd9caCloses#7500
This patch adds the ability for zinject to trigger decryption
and authentication faults in the ZIO and ARC layers. This
functionality is exposed via the new "decrypt" error type, which
may be provided for "data" object types.
This patch also refactors some of the core encryption / decryption
functions so that they have consistent prototypes, handle errors
consistently, and do not have unused arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7474
We should use zfs_dbgmsg instead of spa_dbgmsg. Or at least,
metaslab_condense() should call zfs_dbgmsg because it's important and
rare enough to always log. It's possible that the message in
zio_dva_allocate() would be too high-frequency for zfs_dbgmsg.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Patch Notes:
* Removed ZFS_DEBUG_SPA from zfs-module-parameters.5
OpenZFS-issue: https://www.illumos.org/issues/9236
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cfaba7f668Closes#7467
Only filesystems and volumes are valid 'zfs remap' parameters: when
passed a snapshot name zfs_remap_indirects() does not handle the
EINVAL returned from libzfs_core, which results in failing an assertion
and consequently crashing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7454
This patch fixes 2 issues in how spill blocks are processed during
raw sends. The first problem is that compressed spill blocks were
using the logical length rather than the physical length to
determine how much data to dump into the send stream. The second
issue is a typo that caused the spill record's object number to be
used where the objset's ID number was required. Both issues have
been corrected, and the payload_size is now printed in zstreamdump
for future debugging.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7378Closes#7432
Authored by: Matt Ahrens <Matt.Ahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9280
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/243952cCloses#7445
Remove duplicate segment copies to minimize the possible search
space for reconstruction. Once reduced an accurate assessment can
be made regarding the difficulty in reconstructing the block.
Also, ztest will now run zdb with
zfs_reconstruct_indirect_combinations_max set to 1000000 in an attempt
to avoid checksum errors.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6900
Mirrors are supposed to provide redundancy in the face of whole-disk
failure and silent damage (e.g. some data on disk is not right, but ZFS
hasn't detected the whole device as being broken). However, the current
device removal implementation bypasses some of the mirror's redundancy.
Note that in no case is incorrect data returned, but we might get a
checksum error when we should have been able to find the right data.
There are two underlying problems:
1. When we remove a mirror device, we only read one side of the mirror.
Since we can't verify the checksum, this side may be silently bad, but
the good data is on the other side of the mirror (which we didn't read).
This can cause the removal to "bake in" the busted data – all copies of
the data in the new location are the same, busted version, while we left
the good version behind.
The fix for this is to read and copy both sides of the mirror. If the
old and new vdevs are mirrors, we will read both sides of the old
mirror, and write each copy to the corresponding side of the new mirror.
(If the old and new vdevs have a different number of children, we will
do this as best as possible.) Even though we aren't verifying checksums,
this ensures that as long as there's a good copy of the data, we'll have
a good copy after the removal, even if there's silent damage to one side
of the mirror. If we're removing a mirror that has some silent damage,
we'll have exactly the same damage in the new location (assuming that
the new location is also a mirror).
2. When we read from an indirect vdev that points to a mirror vdev, we
only consider one copy of the data. This can lead to reduced effective
redundancy, because we might read a bad copy of the data from one side
of the mirror, and not retry the other, good side of the mirror.
Note that the problem is not with the removal process, but rather after
the removal has completed (having copied correct data to both sides of
the mirror), if one side of the new mirror is silently damaged, we
encounter the problem when reading the relocated data via the indirect
vdev. Also note that the problem doesn't occur when ZFS knows that one
side of the mirror is bad, e.g. when a disk entirely fails or is
offlined.
The impact is that reads (from indirect vdevs that point to mirrors) may
return a checksum error even though the good data exists on one side of
the mirror, and scrub doesn't repair all data on the mirror (if some of
it is pointed to via an indirect vdev).
The fix for this is complicated by "split blocks" - one logical block
may be split into two (or more) pieces with each piece moved to a
different new location. In this case we need to read all versions of
each split (one from each side of the mirror), and figure out which
combination of versions results in the correct checksum, and then repair
the incorrect versions.
This ensures that we supply the same redundancy whether you use device
removal or not. For example, if a mirror has small silent errors on all
of its children, we can still reconstruct the correct data, as long as
those errors are at sufficiently-separated offsets (specifically,
separated by the largest block size - default of 128KB, but up to 16MB).
Porting notes:
* A new indirect vdev check was moved from dsl_scan_needs_resilver_cb()
to dsl_scan_needs_resilver(), which was added to ZoL as part of the
sequential scrub work.
* Passed NULL for zfs_ereport_post_checksum()'s zbookmark_phys_t
parameter. The extra parameter is unique to ZoL.
* When posting indirect checksum errors the ABD can be passed directly,
zfs_ereport_post_checksum() is not yet ABD-aware in OpenZFS.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9290
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/591Closes#6900
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
zfs-mount-generator implements the "systemd generator" protocol,
producing systemd.mount units from the cached outputs of zfs list,
during early boot, integrating with systemd.
Each pool has an indpendent cache of the command
zfs list -H -oname,mountpoint,canmount -tfilesystem -r $pool
which is kept synchronized by the ZEDLET
history_event-zfs-list-cacher.sh
Datasets not in the cache will be loaded later in the boot process by
zfs-mount.service, including pools without a cache.
Among other things, this allows for complex mount hierarchies.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7329
Currently, "zfs mount -a" will print a warning and fail to mount
any encrypted datasets that do not have a key loaded. This patch
makes the behavior of this failure consistent with other failure
modes ("zfs mount -a" will silently continue, explict "zfs mount"
will print a message and return an error code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7382
Fix a bunch of (mostly) sprintf/snprintf truncation compiler
warnings that show up on Fedora 28 (GCC 8.0.1).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7361Closes#7368
The changes piggyback JSON output support on top of channel programs
(#6558). This way the JSON output support is targeted to scripting
use cases and is easily maintainable since it really only touches
one function (zfs_do_channel_program()).
This patch ports Joyent's JSON nvlist library from illumos to enable
easy JSON printing of channel program output nvlist. To keep the
delta small I also took advantage of the fact that printing in
zfs_do_channel_program() was almost always done before exiting
the program.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7281
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
Change zfs destroy logic so destroying begins before
the entire list of snapshots is built.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7271
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
Some usage patterns like send/recv of replication streams can
produce a large number of events. In such a case, the current
all-syslog.sh zedlet will hold up to its name, and flood the
logs with mostly redundant information. Two mitigate this
situation, this changeset introduces to new variables
ZED_SYSLOG_SUBCLASS_INCLUDE and ZED_SYSLOG_SUBCLASS_EXCLUDE
to zed.rc that give more control over which event classes end
up in the syslog.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6886Closes#7260
1) The Coverity Scan reports some issues for the project
quota patch, including:
1.1) zfs_prop_get_userquota() directly uses the const quota
type value as the condition check by wrong.
1.2) dmu_objset_userquota_get_ids() may cause dnode::dn_newgid
to be overwritten by dnode::dn->dn_oldprojid.
2) This patch fixes related issues. It also enhances the logic
for zfs_project_item_alloc() to avoid buffer overflow.
3) Skip project quota ability check if does not change project
quota related things (id or flag). Otherwise, it will cause
chattr (for other non project quota flags) operation failed
if project quota disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
Closes#7251Closes#7265
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: John Eismeier <john.eismeier@gmail.com>
Closes#7237
Add new script arc_summary3.py as a complete rewrite of the
arc_summary.py tool (see issue #6873)
Add new options:
-g/--graph - Display crude graphic representation
of ARC status and quit
-r/--raw - Print all available information as
minimally formatted list (for grep)
-s/--section - Print a single section. This
replaces -p/--page, which is kept for
backwards use but marked as
depreciated
Add new sections with information on ZIL and SPL. Notify user
if sections L2ARC and VDEV are skipped instead of failing
silently. Add warning that -p/--page option is depreciated.
Developed for Python 3.5.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6873Closes#6892
Add in SMART self-test results to zpool status|iostat -c. This
works for both SAS and SATA drives.
Also, add plumbing to allow the 'smart' script to take smartctl
output from a directory of output text files instead of running
it against the vdevs.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7178
When invoked with wrong parameters 'zfs bookmark' fails to gracefully
validate user input and crashes.
This is a regression accidentally introduced in 587e228; this commit
adds additional tests to the ZFS Test Suite to exercise this codepath.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: KireinaHoro <i@jsteward.moe>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7228Closes#7229
* Add a zed script to kick off a scrub after a resilver. The script is
disabled by default.
* Add a optional $PATH (-P) option to zed to allow it to use a custom
$PATH for its zedlets. This is needed when you're running zed under
the ZTS in a local workspace.
* Update test scripts to not copy in all-debug.sh and all-syslog.sh by
default. They can be optionally copied in as part of zed_setup().
These scripts slow down zed considerably under heavy events loads and
can cause events to be dropped or their delivery delayed. This was
causing some sporadic failures in the 'fault' tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4662Closes#7086
This adds the SMART attributes required to probe Samsung SSD and NVMe
(and possibly others) disks when using the "zpool status -c" command.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7183Closes#7193
This change implements 'zfs send -b' which can be used to send only
received property values whether or not they are overridden by local
settings.
This can be very useful during "restore" operations from a backup pool
because it allows to send only the property values originally sent
from the backup source, even though they were later modified on the
destination either by a 'zfs set' operation, explicit 'zfs inherit' or
overridden during the receive process via 'zfs receive -o|-x'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7156
CID 173243, 173245: Memory - corruptions (OVERRUN)
Added size argument to lcompat_sprintf() to avoid use of INT_MAX
CID 173244: Integer handling issues (OVERFLOW_BEFORE_WIDEN)
Added cast to uint64_t to avoid a 32 bit overflow warning
CID 173242: Integer handling issues (CONSTANT_EXPRESSION_RESULT)
Conditionally removed unused luai_numisnan() floating point check
CID 173241: Resource leaks (RESOURCE_LEAK)
Added missing close(fd) on error path
CID 173240: (UNINIT)
Fixed uninitialized variable in get_special_prop()
CID 147560: Null pointer dereferences (NULL_RETURNS)
Cleaned up bad code merge in dsl_dataset_promote_check()
CID 28475: Memory - illegal accesses (OVERRUN)
Fixed lcompat_sprintf() to use a size paramater
CID 28418, 28422: Error handling issues (CHECKED_RETURN)
Added function result cast to (void) to avoid warning
CID 23935, 28411, 28412: Memory - corruptions (ARRAY_VS_SINGLETON)
Added casts to avoid exposing result as an array
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7181
Project quota is a new ZFS system space/object usage accounting
and enforcement mechanism. Similar as user/group quota, project
quota is another dimension of system quota. It bases on the new
object attribute - project ID.
Project ID is a numerical value to indicate to which project an
object belongs. An object only can belong to one project though
you (the object owner or privileged user) can change the object
project ID via 'chattr -p' or 'zfs project [-s] -p' explicitly.
The object also can inherit the project ID from its parent when
created if the parent has the project inherit flag (that can be
set via 'chattr +P' or 'zfs project -s [-p]').
By accounting the spaces/objects belong to the same project, we
can know how many spaces/objects used by the project. And if we
set the upper limit then we can control the spaces/objects that
are consumed by such project. It is useful when multiple groups
and users cooperate for the same project, or a user/group needs
to participate in multiple projects.
Support the following commands and functionalities:
zfs set projectquota@project
zfs set projectobjquota@project
zfs get projectquota@project
zfs get projectobjquota@project
zfs get projectused@project
zfs get projectobjused@project
zfs projectspace
zfs allow projectquota
zfs allow projectobjquota
zfs allow projectused
zfs allow projectobjused
zfs unallow projectquota
zfs unallow projectobjquota
zfs unallow projectused
zfs unallow projectobjused
chattr +/-P
chattr -p project_id
lsattr -p
This patch also supports tree quota based on the project quota via
"zfs project" commands set as following:
zfs project [-d|-r] <file|directory ...>
zfs project -C [-k] [-r] <file|directory ...>
zfs project -c [-0] [-d|-r] [-p id] <file|directory ...>
zfs project [-p id] [-r] [-s] <file|directory ...>
For "df [-i] $DIR" command, if we set INHERIT (project ID) flag on
the $DIR, then the proejct [obj]quota and [obj]used values for the
$DIR's project ID will be shown as the total/free (avail) resource.
Keep the same behavior as EXT4/XFS does.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by Ned Bass <bass6@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
TEST_ZIMPORT_POOLS="zol-0.6.1 zol-0.6.2 master"
Change-Id: Ib4f0544602e03fb61fd46a849d7ba51a6005693c
Closes#6290
Receiving an incremental stream after an interrupted "zfs receive -s"
fails with the message "dataset is busy": this is because we still have
the hidden clone ../%recv from the resumable receive.
Improve the error message suggesting the existence of a partially
complete resumable stream from "zfs receive -s" which can be either
aborted ("zfs receive -A") or resumed ("zfs send -t").
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7129Closes#7154
zdb -ed on objset for exported pool would failed with:
failed to own dataset 'qq/fs0': No such file or directory
The reason is that zdb pass objset name to spa_import, it uses that
name to create a spa. Later, when dmu_objset_own tries to lookup the spa
using real pool name, it can't find one.
We fix this by make sure we pass pool name rather than objset name to
spa_import.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099Closes#6464
SPA_MAXBLOCKSIZE is too large for stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099
There are some issues in the zdb -R decompression implementation.
The first is that ZLE can easily decompress non-ZLE streams. So we add
ZDB_NO_ZLE env to make zdb skip ZLE.
The second is the random bytes appended to pabd, pbuf2 stuff. This serve
no purpose at all, those bytes shouldn't be read during decompression
anyway. Instead, we randomize lbuf2, so that we can make sure
decompression fill exactly to lsize by bcmp lbuf and lbuf2.
The last one is the condition to detect fail is wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099Closes#4984
zcb_haderrors will be modified in zdb_blkptr_done, which is
asynchronous. So we must move this assignment after zio_wait.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
We want to be able to run channel programs outside of synching
context. This would greatly improve performance for channel programs
that just gather information, as they won't have to wait for synching
context anymore.
=== What is implemented?
This feature introduces the following:
- A new command line flag in "zfs program" to specify our intention
to run in open context. (The -n option)
- A new flag/option within the channel program ioctl which selects
the context.
- Appropriate error handling whenever we try a channel program in
open-context that contains zfs.sync* expressions.
- Documentation for the new feature in the manual pages.
=== How do we handle zfs.sync functions in open context?
When such a function is found by the interpreter and we are running
in open context we abort the script and we spit out a descriptive
runtime error. For example, given the script below ...
arg = ...
fs = arg["argv"][1]
err = zfs.sync.destroy(fs)
msg = "destroying " .. fs .. " err=" .. err
return msg
if we run it in open context, we will get back the following error:
Channel program execution failed:
[string "channel program"]:3: running functions from the zfs.sync
submodule requires passing sync=TRUE to lzc_channel_program()
(i.e. do not specify the "-n" command line argument)
stack traceback:
[C]: in function 'destroy'
[string "channel program"]:3: in main chunk
=== What about testing?
We've introduced new wrappers for all channel program tests that
run each channel program as both (startard & open-context) and
expect the appropriate behavior depending on the program using
the zfs.sync module.
OpenZFS-issue: https://www.illumos.org/issues/8677
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/17a49e15Closes#6558
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#7133
In order to reliably detect deadlocks in the create and import
path ztest should set the failure mode property. This ensures
that the pool is always using the correct failmode behavior.
Removed insidious use of local variable in MAXFAULTS macro.
Converted VERIFY() to VERIFY0() where appropriate.
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7111
Currently, when a raw zfs send file includes a DRR_OBJECT record
that would decrease the number of levels of an existing object,
the object is reallocated with dmu_object_reclaim() which
creates the new dnode using the old object's nlevels. For non-raw
sends this doesn't really matter, but raw sends require that
nlevels on the receive side match that of the send side so that
the checksum-of-MAC tree can be properly maintained. This patch
corrects the issue by freeing the object completely before
allocating it again in this case.
This patch also corrects several issues with dnode_hold_impl()
and related functions that prevented dnodes (particularly
multi-slot dnodes) from being reallocated properly due to
the fact that existing dnodes were not being fully cleaned up
when they were freed.
This patch adds a test to make sure that zfs recv functions
properly with incremental streams containing dnodes of different
sizes.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6821Closes#6864
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
Introduce kstats about the dbuf hash and dbuf cache
to make it easier to inspect state. This should help
with debugging and understanding of these portions
of the codebase.
Correct format of dbuf kstat file.
Introduce a dbc column to dbufs kstat to indicate if
a dbuf is in the dbuf cache.
Introduce field filtering in the dbufstat python script.
Introduce a no header option to the dbufstat python script.
Introduce a test case to test basic mru->mfu list movement
in the ARC.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6906
The zdb(8) command may not terminate in the case where the pool
gets suspended and there is a caller in zio_wait() blocking on
an outstanding read I/O that will never complete. This can in
turn cause ztest(1) to block indefinitely despite the deadman.
Resolve the issue by setting the default failure mode for zdb(8)
to panic. In user space we always want the command to terminate
when forward progress is no longer possible.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
The intent of this patch is extend the existing deadman code
such that it's flexible enough to be used by both ztest and
on production systems. The proposed changes include:
* Added a new `zfs_deadman_failmode` module option which is
used to dynamically control the behavior of the deadman. It's
loosely modeled after, but independant from, the pool failmode
property. It can be set to wait, continue, or panic.
* wait - Wait for the "hung" I/O (default)
* continue - Attempt to recover from a "hung" I/O
* panic - Panic the system
* Added a new `zfs_deadman_ziotime_ms` module option which is
analogous to `zfs_deadman_synctime_ms` except instead of
applying to a pool TXG sync it applies to zio_wait(). A
default value of 300s is used to define a "hung" zio.
* The ztest deadman thread has been re-enabled by default,
aligned with the upstream OpenZFS code, and then extended
to terminate the process when it takes significantly longer
to complete than expected.
* The -G option was added to ztest to print the internal debug
log when a fatal error is encountered. This same option was
previously added to zdb in commit fa603f82. Update zloop.sh
to unconditionally pass -G to obtain additional debugging.
* The FM_EREPORT_ZFS_DELAY event which was previously posted
when the deadman detect a "hung" pool has been replaced by
a new dedicated FM_EREPORT_ZFS_DEADMAN event.
* The proposed recovery logic attempts to restart a "hung"
zio by calling zio_interrupt() on any outstanding leaf zios.
We may want to further restrict this to zios in either the
ZIO_STAGE_VDEV_IO_START or ZIO_STAGE_VDEV_IO_DONE stages.
Calling zio_interrupt() is expected to only be useful for
cases when an IO has been submitted to the physical device
but for some reasonable the completion callback hasn't been
called by the lower layers. This shouldn't be possible but
has been observed and may be caused by kernel/driver bugs.
* The 'zfs_deadman_synctime_ms' default value was reduced from
1000s to 600s.
* Depending on how ztest fails there may be no cache file to
move. This should not be considered fatal, collect the logs
which are available and carry on.
* Add deadman test cases for spa_deadman() and zio_wait().
* Increase default zfs_deadman_checktime_ms to 60s.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Resolve new warnings reported after upgrading to shellcheck
version 0.4.6. This patch contains no functional changes.
* egrep is non-standard and deprecated. Use grep -E instead. [SC2196]
* Check exit code directly with e.g. 'if mycmd;', not indirectly
with $?. [SC2181] Suppressed.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7040
For ztest, which is solely for testing, using a pseudo random
is entirely reasonable. Using /dev/urandom ensures the system
entropy pool doesn't get depleted thus stalling the testing.
This is a particular problem when testing in VMs.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7017Closes#7036
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
In ztest_verify_dnode_bt the ztest_object_lock must be held in
order to safely verify the unused bonus space.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
This fixes zhack's command processing on ARM. On ARM char
is unsigned, and so, in promotion to an int, it will never
compare equal to -1.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Closes#7016
When replacing a faulted device which was previously handled by a spare
multiple levels of nested interior VDEVs will be present in the pool
configuration; the following example illustrates one of the possible
situations:
NAME STATE READ WRITE CKSUM
testpool DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
spare-0 DEGRADED 0 0 0
replacing-0 DEGRADED 0 0 0
/var/tmp/fault-dev UNAVAIL 0 0 0 cannot open
/var/tmp/replace-dev ONLINE 0 0 0
/var/tmp/spare-dev1 ONLINE 0 0 0
/var/tmp/safe-dev ONLINE 0 0 0
spares
/var/tmp/spare-dev1 INUSE currently in use
This is safe and allowed, but get_replication() needs to handle this
situation gracefully to let zpool add new devices to the pool.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6678Closes#6996
This extends vdev_id to support a new slot type, ses, for SCSI Enclosure
Services. With slot type ses, the disk slot numbers are determined by
using the device slot number reported by sg_ses for the device with
matching SAS address, found by querying all available enclosures.
This is primarily of use on systems with a deficient driver omitting
support for bay_identifier in /sys/devices. In my testing, I found that
the existing slot types of port and id were not stable across disk
replacement, so an alternative was required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6956
Using a command similar to 'arc_summary.py | head' causes
a broken pipe exception. Gracefully exit in the case of a
broken pipe in arc_summary.py.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6965Closes#6969
If an invalid option is provided to arc_summary.py we handle any error
thrown from the getopt Python module and print the usage help message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6983
The function that fills the uberblock ring buffer on every device label
has been reworked to avoid occasional failures caused by a race
condition that prevents 'zpool sync' from writing some uberblock
sequentially: this happens when the pool sync ioctl dispatch code calls
txg_wait_synced() while we're already waiting for a TXG to sync.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6924Closes#6977
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6962
* Teach ZED to handle spares usingi the configured ashift: if the zpool
'ashift' property is set then ZED should use its value when kicking
in a hotspare; with this change 512e disks can be used as spares
for VDEVs that were created with ashift=9, even if ZFS natively
detects them as 4K block devices.
* Introduce an additional auto_spare test case which verifies that in
the face of multiple device failures an appropiate number of spares
are kicked in.
* Fix zed_stop() in "libtest.shlib" which did not correctly wait the
target pid.
* Fix ZED crashing on startup caused by a race condition in libzfs
when used in multi-threaded context.
* Convert ZED over to using the tpool library which is already present
in the Illumos FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2562Closes#6858
Fix a segfault when running 'zpool iostat -v 1' while adding
a VDEV.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6748Closes#6872
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
Problem
=======
The current implementation of zil_commit() can introduce significant
latency, beyond what is inherent due to the latency of the underlying
storage. The additional latency comes from two main problems:
1. When there's outstanding ZIL blocks being written (i.e. there's
already a "writer thread" in progress), then any new calls to
zil_commit() will block waiting for the currently oustanding ZIL
blocks to complete. The blocks written for each "writer thread" is
coined a "batch", and there can only ever be a single "batch" being
written at a time. When a batch is being written, any new ZIL
transactions will have to wait for the next batch to be written,
which won't occur until the current batch finishes.
As a result, the underlying storage may not be used as efficiently
as possible. While "new" threads enter zil_commit() and are blocked
waiting for the next batch, it's possible that the underlying
storage isn't fully utilized by the current batch of ZIL blocks. In
that case, it'd be better to allow these new threads to generate
(and issue) a new ZIL block, such that it could be serviced by the
underlying storage concurrently with the other ZIL blocks that are
being serviced.
2. Any call to zil_commit() must wait for all ZIL blocks in its "batch"
to complete, prior to zil_commit() returning. The size of any given
batch is proportional to the number of ZIL transaction in the queue
at the time that the batch starts processing the queue; which
doesn't occur until the previous batch completes. Thus, if there's a
lot of transactions in the queue, the batch could be composed of
many ZIL blocks, and each call to zil_commit() will have to wait for
all of these writes to complete (even if the thread calling
zil_commit() only cared about one of the transactions in the batch).
To further complicate the situation, these two issues result in the
following side effect:
3. If a given batch takes longer to complete than normal, this results
in larger batch sizes, which then take longer to complete and
further drive up the latency of zil_commit(). This can occur for a
number of reasons, including (but not limited to): transient changes
in the workload, and storage latency irregularites.
Solution
========
The solution attempted by this change has the following goals:
1. no on-disk changes; maintain current on-disk format.
2. modify the "batch size" to be equal to the "ZIL block size".
3. allow new batches to be generated and issued to disk, while there's
already batches being serviced by the disk.
4. allow zil_commit() to wait for as few ZIL blocks as possible.
5. use as few ZIL blocks as possible, for the same amount of ZIL
transactions, without introducing significant latency to any
individual ZIL transaction. i.e. use fewer, but larger, ZIL blocks.
In theory, with these goals met, the new allgorithm will allow the
following improvements:
1. new ZIL blocks can be generated and issued, while there's already
oustanding ZIL blocks being serviced by the storage.
2. the latency of zil_commit() should be proportional to the underlying
storage latency, rather than the incoming synchronous workload.
Porting Notes
=============
Due to the changes made in commit 119a394ab0, the lifetime of an itx
structure differs than in OpenZFS. Specifically, the itx structure is
kept around until the data associated with the itx is considered to be
safe on disk; this is so that the itx's callback can be called after the
data is committed to stable storage. Since OpenZFS doesn't have this itx
callback mechanism, it's able to destroy the itx structure immediately
after the itx is committed to an lwb (before the lwb is written to
disk).
To support this difference, and to ensure the itx's callbacks can still
be called after the itx's data is on disk, a few changes had to be made:
* A list of itxs was added to the lwb structure. This list contains
all of the itxs that have been committed to the lwb, such that the
callbacks for these itxs can be called from zil_lwb_flush_vdevs_done(),
after the data for the itxs is committed to disk.
* A list of itxs was added on the stack of the zil_process_commit_list()
function; the "nolwb_itxs" list. In some circumstances, an itx may
not be committed to an lwb (e.g. if allocating the "next" ZIL block
on disk fails), so this list is used to keep track of which itxs
fall into this state, such that their callbacks can be called after
the ZIL's writer pipeline is "stalled".
* The logic to actually call the itx's callback was moved into the
zil_itx_destroy() function. Since all consumers of zil_itx_destroy()
were effectively performing the same logic (i.e. if callback is
non-null, call the callback), it seemed like useful code cleanup to
consolidate this logic into a single function.
Additionally, the existing Linux tracepoint infrastructure dealing with
the ZIL's probes and structures had to be updated to reflect these code
changes. Specifically:
* The "zil__cw1" and "zil__cw2" probes were removed, so they had to be
removed from "trace_zil.h" as well.
* Some of the zilog structure's fields were removed, which affected
the tracepoint definitions of the structure.
* New tracepoints had to be added for the following 3 new probes:
* zil__process__commit__itx
* zil__process__normal__itx
* zil__commit__io__error
OpenZFS-issue: https://www.illumos.org/issues/8585
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5d95a3aCloses#6566
When the pool configuration contains a hole due to a previous device
removal ignore this top level vdev. Failure to do so will result in
the current configuration being assessed to have a non-uniform
replication level and the expected warning will be disabled.
The zpool_add_010_pos test case was extended to cover this scenario.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6907Closes#6911
Display correct data from kstat arcstats for evict_skips,
which is currently repeating the data from mutex_misses.
Fixes#6882
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6882Closes#6883
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Remove unused library re and associated variable kstat_pobj. Add note
to documentation at start of program about required support for old
versions of Python. Change variable "format" (which is a built-in
function) to "fmt".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6869
Prevents arc_summary.py crashing when called with parameter -d or
long form --description with Python3.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6849Closes#6850
Sort list of tunables printed by _tunable_summary()
alphabetically
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6828
Include docstrings (PEP8, PEP257) for module and all functions.
Separately, remove outdated section in comment at start of
module. Separately, remove unused global constant "usetunable".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6818
Complete rewrite of fHits(). Move units from non-standard English
abbreviations to SI units, thereby avoiding confusion because of
"long scale" and "short scale" numbers. Remove unused parameter
"Decimal". Add function string. Aim to confirm to PEP8.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6815
Simplify and inline single-use function div1(); inline twice-used
function div2(); add function comment to zfs_header(); replace
variable "unused" in get_Kstat() with "_" following convention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6802
Porting Notes:
- The OpenZFS patch added nicenum_scale() and nicenum() to a
library not used by ZFS. Rather than pull in a new dependency
the version of nicenum in lib/libzpool/util.c was simply
replaced with the new one.
Reviewed by: Sebastian Wiedenroth <wiedi@frubar.net>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Yuri Pankov <yuripv@gmx.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Authored by: Jason King <jason.brian.king@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/640
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0a055120Closes#6796
Replace if-elif-else construction with shorter loop;
remove unused parameter "Decimal"; centralize format
string; add function documentation string; conform to
PEP8.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6784
Fix compiler warnings in zdb. With these changes, FreeBSD can compile
zdb with all compiler warnings enabled save -Wunused-parameter.
usr/src/cmd/zdb/zdb.c
usr/src/cmd/zdb/zdb_il.c
usr/src/uts/common/fs/zfs/sys/sa.h
usr/src/uts/common/fs/zfs/sys/spa.h
Fix numerous warnings, including:
* const-correctness
* shadowing global definitions
* signed vs unsigned comparisons
* missing prototypes, or missing static declarations
* unused variables and functions
* Unreadable array initializations
* Missing struct initializers
usr/src/cmd/zdb/zdb.h
Add a header file to declare common symbols
usr/src/lib/libzpool/common/sys/zfs_context.h
usr/src/uts/common/fs/zfs/arc.c
usr/src/uts/common/fs/zfs/dbuf.c
usr/src/uts/common/fs/zfs/spa.c
usr/src/uts/common/fs/zfs/txg.c
Add a function prototype for zk_thread_create, and ensure that every
callback supplied to this function actually matches the prototype.
usr/src/cmd/ztest/ztest.c
usr/src/uts/common/fs/zfs/sys/zil.h
usr/src/uts/common/fs/zfs/zfs_replay.c
usr/src/uts/common/fs/zfs/zvol.c
Add a function prototype for zil_replay_func_t, and ensure that
every function of this type actually matches the prototype.
usr/src/uts/common/fs/zfs/sys/refcount.h
Change FTAG so it discards any constness of __func__, necessary
since existing APIs expect it passed as void *.
Porting Notes:
- Many of these fixes have already been applied to Linux. For
consistency the OpenZFS version of a change was applied if the
warning was addressed in an equivalent but different fashion.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8081
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/843abe1b8aCloses#6787
Additionally add four new tests:
* zpool_events_clear: verify 'zpool events -c' functionality
* zpool_events_cliargs: verify command line options and arguments
* zpool_events_follow: verify 'zpool events -f'
* zpool_events_poolname: verify events filtering by pool name
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3285Closes#6762
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
Otherwise, if arcstat gets interrupted before the desired number of
iterations is reached, the output file will be empty (both if set via
'-o' or via shell redirection).
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#6775
Use mfu_size and mru_size pulled from the arcstats
kstat file to calculate the mfu and mru percentages
for arc size breakdown.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: AndCycle <andcycle@andcycle.idv.tw>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5526Closes#6770
Fix new flake8 errors related to bare excepts and ambiguous
variable names due to a STYLE builder update.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6776
Currently the 480GB models of this disk do not use ashift=12 by
default. SSDSC2BW48 is also optimized for 4k blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: adisbladis <adis@blad.is>
Closes#6774
CID 161388: Resource Leak (REASOURCE_LEAK)
Jump to errout so that file descriptor gets closed before returning
from function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6755
CID 147480: Logically dead code (DEADCODE)
Remove non-null check and subsequent function call. Add ASSERT to future
proof the code.
usage label is only jumped to before `zhp` is initialized.
CID 147584: Out-of-bounds access (OVERRUN)
Subtract length of current string from buffer length for `size` argument
to `snprintf`.
Starting address for the write is the start of the buffer + the current
string length. We need to subtract this string length else risk a buffer
overflow.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6745
Several issues were uncovered by running stress tests with zfs
encryption and raw sends in particular. The issues and their
associated fixes are as follows:
* arc_read_done() has the ability to chain several requests for
the same block of data via the arc_callback_t struct. In these
cases, the ARC would only use the first request's dsobj from
the bookmark to decrypt the data. This is problematic because
the first request might be a prefetch zio which is able to
handle the key not being loaded, while the second might use a
different key that it is sure will work. The fix here is to
pass the dsobj with each individual arc_callback_t so that each
request can attempt to decrypt the data separately.
* DRR_FREE and DRR_FREEOBJECT records in a send file were not
having their transactions properly tagged as raw during raw
sends, which caused a panic when the dbuf code attempted to
decrypt these blocks.
* traverse_prefetch_metadata() did not properly set
ZIO_FLAG_SPECULATIVE when issuing prefetch IOs.
* Added a few asserts and code cleanups to ensure these issues
are more detectable in the future.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Make two instances of the same change. Change bitwise AND (&) to logical
AND (&&).
Currently the code uses a bitwise AND between two boolean values.
In the first instance;
The first operand is a flag that has been bitwise combined with a bit
mask to get a boolean value as to whether a file has group write
permissions set.
The second operand used is a struct member that is intended as a
boolean flag not a bit mask.
In the second instance the argument is the same except with world write
permissions instead of group write (S_IWOTH, S_IWGRP).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6684Closes#6722
On systems with SCSI rather than SAS disk topology, this change enables
the vdev_id script to match against the block device path, and therefore
create a vdev alias in /dev/disk/by-vdev.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6592
Quote "$MMP_IMPORT_MSG" when it is passed as an argument, as it is a
multi-word string. Some tests were passing when they should not have,
because the grep was only testing for the first word.
Correct the message expected when no hostid is set and the test attempts
to enable multihost. It did not match the actual output in that
situation.
Disable ztest_reguid() when ztest is invoked with the -M option. If
ztest performs a reguid, a concurrent import attempt may fail with the
error "one or more devices is currently unavailable" if the guid sum is
calculated on the original device guids but compared against the guid
sum ztest wrote based on the new device guids.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6666
FRU and LIBTOPO support are illumos only features that will not be ported to
Linux and make the code more complicated than necessary. This commit
makes way for further cleanups of the zed/FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6641
The build for ztest always enabled debug information but does not enable
asserts unless --enable-debug is used. This will always enable asserts
in the ztest code.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6640
This leverages the functionality introduced in cf7684b to expose
verbose, dry-run and parsable 'zfs send' options for bookmarks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3666Closes#6601
Refactor dmu_object_alloc_dnsize() and dnode_hold_impl() to simplify the
code, fix errors introduced by commit dbeb879 (PR #6117) interacting
badly with large dnodes, and improve performance.
* When allocating a new dnode in dmu_object_alloc_dnsize(), update the
percpu object ID for the core's metadnode chunk immediately. This
eliminates most lock contention when taking the hold and creating the
dnode.
* Correct detection of the chunk boundary to work properly with large
dnodes.
* Separate the dmu_hold_impl() code for the FREE case from the code for
the ALLOCATED case to make it easier to read.
* Fully populate the dnode handle array immediately after reading a
block of the metadnode from disk. Subsequently the dnode handle array
provides enough information to determine which dnode slots are in use
and which are free.
* Add several kstats to allow the behavior of the code to be examined.
* Verify dnode packing in large_dnode_008_pos.ksh. Since the test is
purely creates, it should leave very few holes in the metadnode.
* Add test large_dnode_009_pos.ksh, which performs concurrent creates
and deletes, to complement existing test which does only creates.
With the above fixes, there is very little contention in a test of about
200,000 racing dnode allocations produced by tests 'large_dnode_008_pos'
and 'large_dnode_009_pos'.
name type data
dnode_hold_dbuf_hold 4 0
dnode_hold_dbuf_read 4 0
dnode_hold_alloc_hits 4 3804690
dnode_hold_alloc_misses 4 216
dnode_hold_alloc_interior 4 3
dnode_hold_alloc_lock_retry 4 0
dnode_hold_alloc_lock_misses 4 0
dnode_hold_alloc_type_none 4 0
dnode_hold_free_hits 4 203105
dnode_hold_free_misses 4 4
dnode_hold_free_lock_misses 4 0
dnode_hold_free_lock_retry 4 0
dnode_hold_free_overflow 4 0
dnode_hold_free_refcount 4 57
dnode_hold_free_txg 4 0
dnode_allocate 4 203154
dnode_reallocate 4 0
dnode_buf_evict 4 23918
dnode_alloc_next_chunk 4 4887
dnode_alloc_race 4 0
dnode_alloc_next_block 4 18
The performance is slightly improved for concurrent creates with
16+ threads, and unchanged for low thread counts.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5396Closes#6522Closes#6414Closes#6564
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6535
Since OpenZFS 7578 (1b7c1e5) if we have a ZVOL with logbias=throughput
we will force WR_INDIRECT itxs in zvol_log_write() setting itx->itx_lr
offset and length to the offset and length of the BIO from
zvol_write()->zvol_log_write(): these offset and length are later used
to take a range lock in zillog->zl_get_data function: zvol_get_data().
Now suppose we have a ZVOL with blocksize=8K and push 4K writes to
offset 0: we will only be range-locking 0-4096. This means the
ASSERTion we make in dbuf_unoverride() is no longer valid because now
dmu_sync() is called from zilog's get_data functions holding a partial
lock on the dbuf.
Fix this by taking a range lock on the whole block in zvol_get_data().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6238Closes#6315Closes#6356Closes#6477
* Removed zpios kmod, utility, headers and man page.
* Removed unused scripts zpios-profile/*, zpios-test/*,
zpool-config/*, smb.sh, zpios-sanity.sh, zpios-survey.sh,
zpios.sh, and zpool-create.sh.
* Removed zfs-script-config.sh.in. When building 'make' generates
a common.sh with in-tree path information from the common.sh.in
template. This file and sourced by the test scripts and used
for in-tree testing, it is not included in the packages. When
building packages 'make install' uses the same template to
create a new common.sh which is appropriate for the packaging.
* Removed unused functions/variables from scripts/common.sh.in.
Only minimal path information and configuration environment
variables remain.
* Removed unused scripts from scripts/ directory.
* Remaining shell scripts in the scripts directory updated to
cleanly pass shellcheck and added to checked scripts.
* Renamed tests/test-runner/cmd/ to tests/test-runner/bin/ to
match install location name.
* Removed last traces of the --enable-debug-dmu-tx configure
options which was retired some time ago.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6509
With HPE hardware and hpsa-driven SAS adapters, only a single phy is
reported, but no individual per-port phys (ie. no phy* entry below
port_dir), which breaks topology detection in the current sas_handler
code. Instead, slot information can be derived directly from the port
number. This change implements a new slot keyword "port" similar to
"id" and "lun", and assumes a default phy/port of 0 if no individual
phy entry can be found. It allows to use the "sas_direct" topology with
current HPE Dxxxx and Apollo 45xx JBODs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6484
Added a 'corrupt' error option that will flip a bit in the data
after a read operation. This is useful for generating checksum
errors at the device layer (in a mirror config for example). It
is also used to validate the diagnosis of checksum errors from
the zfs diagnosis engine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6345
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
* Simplify threads, mutexs, cvs and rwlocks
* Update the zk_thread_create() function to use the same trick
as Illumos. Specifically, cast the new pthread_t to a void
pointer and return that as the kthread_t *. This avoids the
issues associated with managing a wrapper structure and is
safe as long as the callers never attempt to dereference it.
* Update all function prototypes passed to pthread_create() to
match the expected prototype. We were getting away this with
before since the function were explicitly cast.
* Replaced direct zk_thread_create() calls with thread_create()
for code consistency. All consumers of libzpool now use the
proper wrappers.
* The mutex_held() calls were converted to MUTEX_HELD().
* Removed all mutex_owner() calls and retired the interface.
Instead use MUTEX_HELD() which provides the same information
and allows the implementation details to be hidden. In this
case the use of the pthread_equals() function.
* The kthread_t, kmutex_t, krwlock_t, and krwlock_t types had
any non essential fields removed. In the case of kthread_t
and kcondvar_t they could be directly typedef'd to pthread_t
and pthread_cond_t respectively.
* Removed all extra ASSERTS from the thread, mutex, rwlock, and
cv wrapper functions. In practice, pthreads already provides
the vast majority of checks as long as we check the return
code. Removing this code from our wrappers help readability.
* Added TS_JOINABLE state flag to pass to request a joinable rather
than detached thread. This isn't a standard thread_create() state
but it's the least invasive way to pass this information and is
only used by ztest.
TEST_ZTEST_TIMEOUT=3600
Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4547Closes#5503Closes#5523Closes#6377Closes#6495
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Sen Haerens <sen@senhaerens.be>
Closes#6444Closes#6445
Check in the DMU whether an object record in a send stream being
received contains an unsupported dnode slot count, and return an
error if it does. Failure to catch an unsupported dnode slot count
would result in a panic when the SPA attempts to increment the
reference count for the large_dnode feature and the pool has the
feature disabled. This is not normally an issue for a well-formed
send stream which would have the DMU_BACKUP_FEATURE_LARGE_DNODE flag
set if it contains large dnodes, so it will be rejected as
unsupported if the required feature is disabled. This change adds a
missing object record field validation.
Add missing stream feature flag checks in
dmu_recv_resume_begin_check().
Consolidate repetitive comment blocks in dmu_recv_begin_check().
Update zstreamdump to print the dnode slot count (dn_slots) for an
object record when running in verbose mode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6396
Add a callback to wake all running mmp threads when
zfs_multihost_interval is changed.
This is necessary when the interval is changed from a very large value
to a significantly lower one, while pools are imported that have the
multihost property enabled.
Without this commit, the mmp thread does not wake up and detect the new
interval until after it has waited the old multihost interval time. A
user monitoring mmp writes via the provided kstat would be led to
believe that the changed setting did not work.
Added a test in the ZTS under mmp to verify the new functionality is
working.
Added a test to ztest which starts and stops mmp threads, and calls into
the code to signal sleeping mmp threads, to test for deadlocks or
similar locking issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6387
"zhack feature stat" performs a read-only import, so the MMP activity
check is not necessary.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388Closes#6389
Turning the multihost property on requires that a hostid be set to allow
ZFS to determine when a foreign system is attemping to import a pool.
The error message instructing the user to set a hostid refers to
genhostid(1).
Genhostid(1) is not available on SUSE Linux. This commit adds a script
modeled after genhostid(1) for those users.
Zgenhostid checks for an /etc/hostid file; if it does not exist, it
creates one and stores a value. If the user has provided a hostid as an
argument, that value is used. Otherwise, a random hostid is generated
and stored.
This differs from the CENTOS 6/7 versions of genhostid, which overwrite
the /etc/hostid file even though their manpages state otherwise.
A man page for zgenhostid is added. The one for genhostid is in (1), but
I put zgenhostid in (8) because I believe it's more appropriate.
The mmp tests are modified to use zgenhostid to set the hostid instead
of using the spl_hostid module parameter. zgenhostid will not replace
an existing /etc/hostid file, so new mmp_clear_hostid calls are
required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6358Closes#6379
When replacing a disk with non-wholedisk spare, we shouldn't zero_label
it. The wholedisk case already skip it. In fact, zero_label function
will fail saying device busy because it's already opened exclusively,
but since there's no error checking, the replace command will succeed,
causing great confusion.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6369
zpool iostat/status -c is supposed to be restricted
by its search path, but currently isn't. To prevent
arbitrary scripts from being executed, disallow '/'
from commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6353Closes#6359
CID 165757: Control flow issues (MISSING_BREAK)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#6348
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8067
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8173085Closes#6319
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The problem is that zfs_get_data() supplies a stale zgd_bp to
dmu_sync(), which we then nopwrite against.
zfs_get_data() doesn't hold any DMU-related locks, so after it
copies db_blkptr to zgd_bp, dbuf_write_ready() could change
db_blkptr, and dbuf_write_done() could remove the dirty record.
dmu_sync() then sees the stale BP and that the dbuf it not dirty,
so it is eligible for nop-writing.
The fix is for dmu_sync() to copy db_blkptr to zgd_bp after
acquiring the db_mtx. We could still see a stale db_blkptr,
but if it is stale then the dirty record will still exist and
thus we won't attempt to nopwrite.
OpenZFS-issue: https://www.illumos.org/issues/8378
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3127742Closes#6293
Resolves issues discovered when porting to OpenZFS.
* Lint warnings.
* Made dnode_move_impl() large dnode aware. This
functionality is currently unused on Linux.
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6262
GCC 7.1 with will warn when we're not checking the snprintf()
return code in cases where the buffer could be truncated. This
patch either checks the snprintf return code (where applicable),
or simply disables the warnings (ztest.c).
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6253
This prints dashes instead of zeros for zero latency values in
'zpool iostat -p'. You'll get zero latencies reported when the
disk is idle, but technically a zero latency is invalid, since you
can't measure the latency of doing nothing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6210
In the original form of device error injection, it was an all or nothing
situation. To help simulate intermittent error conditions, you can now
specify a real number percentage value. This is also very useful for our
ZFS fault diagnosis testing and for injecting intermittent errors during
load testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6227
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Jack Draak <jackdraak@gmail.com>
Signed-off-by: Kash Pande <kash@tripleback.net>
Closes#6203
- After some ZIL changes 6 years ago zil_slog_limit got partially broken
due to zl_itx_list_sz not updated when async itx'es upgraded to sync.
Actually because of other changes about that time zl_itx_list_sz is not
really required to implement the functionality, so this patch removes
some unneeded broken code and variables.
- Original idea of zil_slog_limit was to reduce chance of SLOG abuse by
single heavy logger, that increased latency for other (more latency critical)
loggers, by pushing heavy log out into the main pool instead of SLOG. Beside
huge latency increase for heavy writers, this implementation caused double
write of all data, since the log records were explicitly prepared for SLOG.
Since we now have I/O scheduler, I've found it can be much more efficient
to reduce priority of heavy logger SLOG writes from ZIO_PRIORITY_SYNC_WRITE
to ZIO_PRIORITY_ASYNC_WRITE, while still leave them on SLOG.
- Existing ZIL implementation had problem with space efficiency when it
has to write large chunks of data into log blocks of limited size. In some
cases efficiency stopped to almost as low as 50%. In case of ZIL stored on
spinning rust, that also reduced log write speed in half, since head had to
uselessly fly over allocated but not written areas. This change improves
the situation by offloading problematic operations from z*_log_write() to
zil_lwb_commit(), which knows real situation of log blocks allocation and
can split large requests into pieces much more efficiently. Also as side
effect it removes one of two data copy operations done by ZIL code WR_COPIED
case.
- While there, untangle and unify code of z*_log_write() functions.
Also zfs_log_write() alike to zvol_log_write() can now handle writes crossing
block boundary, that may also improve efficiency if ZPL is made to do that.
Sponsored by: iXsystems, Inc.
Authored by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7578
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aeb13acCloses#6191
Commit torvalds/linux@9e8925b6 allowed for kernels to be built
without support for mandatory locking (MS_MANDLOCK). This will
result in 'zfs mount' failing when the nbmand=on property is set
if the kernel is built without CONFIG_MANDATORY_FILE_LOCKING.
Unfortunately we can not reliably detect prior to the mount(2) system
call if the kernel was built with this support. The best we can do
is check if the mount failed with EPERM and if we passed 'mand'
as a mount option and then print a more useful error message. e.g.
filesystem 'tank/fs' has the 'nbmand=on' property set, this mount
option may be disabled in your kernel. Use 'zfs set nbmand=off'
to disable this option and try to mount the filesystem again.
Additionally, switch the default error message case to use
strerror() to produce a more human readable message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4729Closes#6199
Allow new members to be added to a pool mixing raidz and mirror vdevs
without giving -f, as long as they have matching redundancy. This case
was missed in #5915, which only handled zpool create.
Add zfstest zpool_add_010_pos.ksh, with test of zpool create
followed by zpool add of mixed raidz and mirror vdevs.
Add some more mixed raidz and mirror cases to zpool_create_006_pos.ksh.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan Johansson <f96hajo@chalmers.se>
Issue #5915Closes#6181
Users can now provide their own scripts to be run
with 'zpool iostat/status -c'. User scripts should be
placed in ~/.zpool.d to be included in zpool's
default search path.
Provide a script which can be used with
'zpool iostat|status -c' that will return the type of
device (hdd, sdd, file).
Provide a script to get various values from smartctl
when using 'zpool iostat/status -c'.
Allow users to define the ZPOOL_SCRIPTS_PATH
environment variable which can be used to override
the default 'zpool iostat/status -c' search path.
Allow the ZPOOL_SCRIPTS_ENABLED environment
variable to enable or disable 'zpool status/iostat -c'
functionality.
Use the new smart script to provide the serial command.
Install /etc/sudoers.d/zfs file which contains the sudoer
rule for smartctl as a sample.
Allow 'zpool iostat/status -c' tests to run in tree.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6121Closes#6153
Enable most of the remaining test cases which were previously
disabled. The required fixes are as follows:
* cache_001_pos - No changes required.
* cache_010_neg - Updated to use losetup under Linux. Loopback
cache devices are allowed, ZVOLs as cache devices are not.
Disabled until all the builders pass reliably.
* cachefile_001_pos, cachefile_002_pos, cachefile_003_pos,
cachefile_004_pos - Set set_device_dir path in cachefile.cfg,
updated CPATH1 and CPATH2 to reference unique files.
* zfs_clone_005_pos - Wait for udev to create volumes.
* zfs_mount_007_pos - Updated mount options to expected Linux names.
* zfs_mount_009_neg, zfs_mount_all_001_pos - No changes required.
* zfs_unmount_005_pos, zfs_unmount_009_pos, zfs_unmount_all_001_pos -
Updated to expect -f to not unmount busy mount points under Linux.
* rsend_019_pos - Observed to occasionally take a long time on both
32-bit systems and the kmemleak builder.
* zfs_written_property_001_pos - Switched sync(1) to sync_pool.
* devices_001_pos, devices_002_neg - Updated create_dev_file() helper
for Linux.
* exec_002_neg.ksh - Fixed mmap_exec.c to preserve errno. Updated
test case to expect EPERM from Linux as described by mmap(2).
* grow_pool_001_pos - Adding missing setup.ksh and cleanup.ksh
scripts from OpenZFS.
* grow_replicas_001_pos.ksh - Added missing $SLICE_* variables.
* history_004_pos, history_006_neg, history_008_pos - Fixed by
previous commits and were not enabled. No changes required.
* zfs_allow_010_pos - Added missing spaces after assorted zfs
commands in delegate_common.kshlib.
* inuse_* - Illumos dump device tests skipped. Remaining test
cases updated to correctly create required partitions.
* large_files_001_pos - Fixed largest_file.c to accept EINVAL
as well as EFBIG as described in write(2).
* link_count_001 - Added nproc to required commands.
* umountall_001 - Updated to use umount -a.
* online_offline_001_* - Pull in OpenZFS change to file_trunc.c
to make the '-c 0' option run the test in a loop. Included
online_offline.cfg file in all test cases.
* rename_dirs_001_pos - Updated to use the rename_dir test binary,
pkill restricted to exact matches and total runtime reduced.
* slog_013_neg, write_dirs_002_pos - No changes required.
* slog_013_pos.ksh - Updated to use losetup under Linux.
* slog_014_pos.ksh - ZED will not be running, manually degrade
the damaged vdev as expected.
* nopwrite_varying_compression, nopwrite_volume - Forced pool
sync with sync_pool to ensure up to date property values.
* Fixed typos in ZED log messages. Refactored zed_* helper
functions to resolve all-syslog exit=1 errors in zedlog.
* zfs_copies_005_neg, zfs_get_004_pos, zpool_add_004_pos,
zpool_destroy_001_pos, largest_pool_001_pos, clone_001_pos.ksh,
clone_001_pos, - Skip until layering pools on zvols is solid.
* largest_pool_001_pos - Limited to 7eb pool, maximum
supported size in 8eb-1 on Linux.
* zpool_expand_001_pos, zpool_expand_003_neg - Requires
additional support from the ZED, updated skip reason.
* zfs_rollback_001_pos, zfs_rollback_002_pos - Properly cleanup
busy mount points under Linux between test loops.
* privilege_001_pos, privilege_003_pos, rollback_003_pos,
threadsappend_001_pos - Skip with log_unsupported.
* snapshot_016_pos - No changes required.
* snapshot_008_pos - Increased LIMIT from 512K to 2M and added
sync_pool to avoid false positives.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6128
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
Enable additional test cases, in most cases this required a few
minor modifications to the test scripts. In a few cases a real
bug was uncovered and fixed. And in a handful of cases where pools
are layered on pools the test case will be skipped until this is
supported. Details below for each test case.
* zpool_add_004_pos - Skip test on Linux until adding zvols to pools
is fully supported and deadlock free.
* zpool_add_005_pos.ksh - Skip dumpadm portion of the test which isn't
relevant for Linux. The find_vfstab_dev, find_mnttab_dev, and
save_dump_dev functions were updated accordingly for Linux. Add
O_EXCL to the in-use check to prevent the -f (force) option from
working for mounted filesystems and improve the resulting error.
* zpool_add_006_pos - Update test case such that it doesn't depend
on nested pools. Switch to truncate from mkfile to reduce space
requirements and speed up the test case.
* zpool_clear_001_pos - Speed up test case by filling filesystem to
25% capacity.
* zpool_create_002_pos, zpool_create_004_pos - Use sparse files for
file vdevs in order to avoid increasing the partition size.
* zpool_create_006_pos - 6ba1ce9 allows raidz+mirror configs with
similar redundancy. Updating the valid_args and forced_args cases.
* zpool_create_008_pos - Disable overlapping partition portion.
* zpool_create_011_neg - Fix to correctly create the extra partition.
Modified zpool_vdev.c to use fstat64_blk() wrapper which includes
the st_size even for block devices.
* zpool_create_012_neg - Updated to properly find swap devices.
* zpool_create_014_neg, zpool_create_015_neg - Updated to use
swap_setup() and swap_cleanup() wrappers which do the right thing
on Linux and Illumos. Removed '-n' option which succeeds under
Linux due to differences in the in-use checks.
* zpool_create_016_pos.ksh - Skipped test case isn't useful.
* zpool_create_020_pos - Added missing / to cleanup() function.
Remove cache file prior to test to ensure a clean environment
and avoid false positives.
* zpool_destroy_001_pos - Removed test case which creates a pool on
a zvol. This is more likely to deadlock under Linux and has never
been completely supported on any platform.
* zpool_destroy_002_pos - 'zpool destroy -f' is unsupported on Linux.
Mount point must not be busy in order to unmount them.
* zfs_destroy_001_pos - Handle EBUSY error which can occur with
volumes when racing with udev.
* zpool_expand_001_pos, zpool_expand_003_neg - Skip test on Linux
until adding zvols to pools is fully supported and deadlock free.
The test could be modified to use loop-back devices but it would
be preferable to use the test case as is for improved coverage.
* zpool_export_004_pos - Updated test case to such that it doesn't
depend on nested pools. Normal file vdev under /var/tmp are fine.
* zpool_import_all_001_pos - Updated to skip partition 1, which is
known as slice 2, on Illumos. This prevents overwriting the
default TESTPOOL which was causing the failure.
* zpool_import_002_pos, zpool_import_012_pos - No changes needed.
* zpool_remove_003_pos - No changes needed
* zpool_upgrade_002_pos, zpool_upgrade_004_pos - Root cause addressed
by upstream OpenZFS commit 3b7f360.
* zpool_upgrade_007_pos - Disabled in test case due to known failure.
Opened issue https://github.com/zfsonlinux/zfs/issues/6112
* zvol_misc_002_pos - Updated to to use ext2.
* zvol_misc_001_neg, zvol_misc_003_neg, zvol_misc_004_pos,
zvol_misc_005_neg, zvol_misc_006_pos - Moved to skip list, these
test case could be updated to use Linux's crash dump facility.
* zvol_swap_* - Updated to use swap_setup/swap_cleanup helpers.
File creation switched from /tmp to /var/tmp. Enabled minimal
useful tests for Linux, skip test cases which aren't applicable.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3484
Issue #5634
Issue #2437
Issue #5202
Issue #4034Closes#6095
This allows users to specify "-o property=value" to override and
"-x property" to exclude properties when receiving a zfs send stream.
Both native and user properties can be specified.
This is useful when using zfs send/receive for periodic
backup/replication because it lets users change properties such as
canmount, mountpoint, or compression without modifying the source.
References:
https://www.illumos.org/issues/2745https://www.illumos.org/issues/3753
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1350Closes#5349
CID 161638: Resource leak (RESOURCE_LEAK)
Ensure the string array in print_zpool_script_help
is freed in cases when there is an error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6111
The proposed debugging enhancements in zfsonlinux/spl#587
identified the following missing *_destroy/*_fini calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5428
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
* Add zfs_nicebytes() to print human-readable sizes
Some 'zfs', 'zpool' and 'zdb' output strings can be confusing to the
user when no units are specified. This add a new zfs_nicenum_format
"ZFS_NICENUM_BYTES" used to print bytes in their human-readable form.
Additionally, update some test cases to use machine-parsable 'zfs get'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2414Closes#3185Closes#3594Closes#6032
OpenZFS 7252 - compressed zfs send / receive
OpenZFS 7628 - create long versions of ZFS send / receive options
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: bunder2015 <omfgbunder@gmail.com>
Ported-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Most of 7252 was already picked up during ABD work. This
commit represents the gap from the final commit to openzfs.
- Fixed split_large_blocks check in do_dump()
- An alternate version of the write_compressible() function was
implemented for Linux which does not depend on fio. The behavior
of fio differs significantly based on the exact version.
- mkholes was replaced with truncate for Linux.
OpenZFS-issue: https://www.illumos.org/issues/7252
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5602294Closes#6067
This patch updates the "zpool status/iostat -c" commands to only run
"pre-baked" scripts from the /etc/zfs/zpool.d directory (or wherever
you install to). The scripts can only be run from -c as an unprivileged
user (unless the ZPOOL_SCRIPTS_AS_ROOT environment var is
set by root). This was done to encourage scripts to be written is such
a way that normal users can use them, and to be cautious. If your
script needs to run a privileged command, consider adding the
appropriate line in /etc/sudoers. See zpool(8) for an example of how
to do this.
The patch also allows the scripts to output custom column names. If
the script outputs a line like:
name=value
then "name" is used for the column name, and "value" is its value.
Multiple columns can be specified by outputting multiple lines. Column
names and values can have spaces. If the value is empty, a dash (-) is
printed instead.
After all the "name=value" lines are read (if any), zpool will take the
next the next line of output (if any) and print it without a column
header. After that, no more lines will be processed. This can be
useful for printing errors.
Lastly, this patch also disables the -c option with the latency and
request size histograms, since it produced awkward output and made the
code harder to maintain.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5852
* bookmarks are not supported when sending all intermediary snaps (-I)
* add missing compressed (-c) option to the 'zfs' help and manpage
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6028
Udev may fail to create the expected symbolic links in
/dev/disk/by-vdev on systems with the
device-mapper-multipath-0.4.9-100.el6 package installed. This affects
RHEL 6.9 and possibly other downstream distributions.
That version of the multipath command may incorrectly list a drive
state as "unkown" instead of "running". The issue was introduced
in the patch for https://bugzilla.redhat.com/show_bug.cgi?id=1401769
The vdev_id udev helper uses the state reported by "multipath -l" to
detect an online component disk of a multipath device in order to
resolve its physical slot and enclosure. Changing the command
invocation to "multipath -ll" works around the above issue by causing
multipath to consult additional sources of information to determine
the drive state.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6039
This lets users create a bookmark from the command line by its name
only, without the need to specify the dataset path which is extacted
from the snapshot parameter.
These commands are now equivalent:
zfs bookmark poolname/fs@snap poolname/fs#bookmark
zfs bookmark @snap poolname/fs#bookmark
zfs bookmark poolname/fs@snap \#bookmark
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3665Closes#6027
Authored by: Richard Yao <ryao@gentoo.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
This was already implemented in ZFS on Linux. This patch
is to resolved the deltas present in our version.
OpenZFS-issue: https://www.illumos.org/issues/6392
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/9bb97deCloses#6020
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
There are two reasons:
1) Finding a znode's path is slower than printing any other znode
information at verbosity < 5.
2) On a corrupted pool like the one mentioned below, zdb will crash when it
tries to determine the znode's path. But with this patch, zdb can still
extract useful information from such pools.
OpenZFS-issue: https://www.illumos.org/issues/7900
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2b0dee1Closes#6016
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Will Andrews <will@freebsd.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Replaced zdb.8 with upstream mdoc zdb.1m version. Updated to
include Linux specific features: -V verbatium imports and
improved label printing (-u, and -l).
- Minor changes to `zdb -h` output to honor 80 character limit.
OpenZFS-issue: https://www.illumos.org/issues/6410
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ed61ec1Closes#6006
Be sure to invalidate a vdev's cache before performing
a zpool labelclear. There are cases where the cache is
stale because we did some operation that bypassed it,
and since we are doing an open with only O_RDWR, we
should invalidate it to be safe.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6009
GCC 4.9.4 complains about implicit function declarations when building
against musl on Gentoo.
zed_log.c: In function ‘zed_log_pipe_open’:
zed_log.c:69:7: warning: implicit declaration of function ‘getpid’
(int)getpid());
^
zed_log.c:71:2: warning: implicit declaration of function ‘pipe’
if (pipe(_ctx.pipe_fd) < 0)
^
zed_log.c: In function ‘zed_log_pipe_close_reads’:
zed_log.c:90:2: warning: implicit declaration of function ‘close’
if (close(_ctx.pipe_fd[0]) < 0)
^
zed_log.c: In function ‘zed_log_pipe_wait’:
zed_log.c:141:3: warning: implicit declaration of function ‘read’
n = read(_ctx.pipe_fd[0], &c, sizeof (c));
The [-Wimplicit-function-declaration] at the end of each warning has
been removed to meet comment style requirements.
The man pages say to include <sys/types.h> and <unistd.h>. Doing that
silences the warnings.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#5993
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Updated 'zpool labelclear' and 'zdb -l' such that they attempt
to find a vdev given solely its short name. This behavior is
consistent with the upstream OpenZFS code and the test cases
depend on it. The actual implementation differs slightly due
to device naming conventions on Linux.
- auto_online_001_pos, auto_replace_001_pos and add-o_ashift
test cases updated to expect failure when no label exists.
- read_efi_label() and zpool_label_disk_check() are read-only
operations and should use O_RDONLY at open time to enforce this.
- zpool_label_disk() and zpool_relabel_disk() write the partition
information using O_DIRECT an fsync() and page cache invalidation
to ensure a consistent view of the device.
- dump_label() in zdb should invalidate the page cache in order
to get the authoritative label from disk.
OpenZFS-issue: https://www.illumos.org/issues/6865
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c95076cCloses#5981
CID 161288: Null pointer dereferences (REVERSE_INULL)
Ensure physpath != NULL before the strcmp.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5974
Also included are updates to auto-online test
Automated auto-replace test to go along with ZED FMA integration
(PR 4673) auto-replace_001.pos works using a scsi_debug device
(the only usable virtual device currently due to whole_disk var
needing to be set)
Functionality for automated FMA auto-replace test to work with
scsi_debug devs: Some functionality/exceptions needed to be
added for automation of auto-replace to work correctly.
In the test an alias vdev_id rule is added for any scsi_debug
device which sets the phys_path="scsidebug" after a udevadm
trigger command.
A symlink is created for the vdev_id.conf file (in /etc/zfs/ by
default) to be used in-tree for the test suite
(/var/tmp/zfs/vdev_id.conf). "./scripts/zfs-helpers.sh -i" needs
to be run before fault tests in the ZTS (to use udev rules in-tree)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Sydney Vanda <sydney.m.vanda@intel.com>
Closes#5944
Allow a pool to be created with both raidz and mirror members,
without giving -f, as long as they have matching redundancy.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5915
CID 161264: Uninitialized variables (UNINIT)
In _zed_event_add_nvpair, when handling DATA_TYPE_UINT64,
we should be using i64 throughout the entire case.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5964
* Add ZPOOL pool state to zfs_post_common to
allow differentiation between export and destroy
by zedlets.
* Add pool name as standard export This ensures
pool name is exported to zedlets.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Closes#5942
Wherever possible it's best to avoid depending on a linear ABD.
Update the code accordingly in the following areas.
- vdev_raidz
- zio, zio_checksum
- zfs_fm
- change abd_alloc_for_io() to use abd_alloc()
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5668
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: SenH <sen@senhaerens.be>
Closes#5933
Add trivial libzfs_fru_compare() function which can be used when
HAVE_LIBTOPO is not defined. The only caller is find_vdev() and
this function should never be reached because search_fru must be
NULL unless HAVE_LIBTOPO is defined.
Rename _HAS_FMD_TOPO to existing HAVE_LIBTOPO which was
originally added for this purpose. This macro will never be defined.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5402Closes#5909
When a pool is suspended it's impossible to read the list
of damaged files from disk. This would result in a generic
misleading "insufficient permissions" error message.
Update zpool_get_errlog() to use the standard zpool error
logging functions to generate a useful error message. In
this case:
errors: List of errors unavailable: pool I/O is currently suspended
This patch does not address the related issue of potentially
not being able to resume a suspend pool when the underlying
device names have changed.
Additionally, remove the error handling from zfs_alloc()
in zpool_get_errlog() for readability since this function
can never fail.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4031Closes#5731Closes#5907
Several functions were renamed when ZFS was originally ported to
Linux. Revert the code to the original names to minimize the
delta with upstream OpenZFS.
zfs_sb_teardown -> zfsvfs_teardown
zfs_sb_create -> zfsvfs_create
zfs_sb_setup -> zfsvfs_setup
zfs_sb_free -> zfsvfs_free
get_zfs_sb -> getzfsvfs
zfs_sb_hold -> zfsvfs_hold
zfs_sb_rele -> zfsvfs_rele
zfs_sb_prune_aliases -> zfs_prune_aliases (Linux-only)
zfs_sb_prune -> zfs_prune (Linux only)
Align the zfs_vnops.h and zfs_vfsops.h with upstream as much
as possible. Several prototypes were removed and those that
remain were reordered.
Move the EXPORT_SYMBOL lines to the end of the source files
for consistency with the other source files.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
arc_summary and dbufstat should have two spaces
after their last function definitions.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5881
Enable shellcheck to run on zed scripts,
paxcheck.sh, zfs-tests.sh, zfs.sh, and zloop.sh.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5812
For zdb -l, detect when the configuration nvlist in some label l (l>0)
is the same as a configuration already dumped. If so, do not dump it.
Make a similar check when dumping Uberblocks for zdb -lu. Check whether
a label already dumped contains an identical Uberblock. If so, do not
dump the Uberblock.
When dumping a configuration or Uberblock, state which labels it is
found in (0-3), for example: labels = 1 2 3
Detecting redundant uberblocks or configurations is accomplished by
calculating checksums of the uberblocks and the packed nvlists
containing the configuration.
If there is nothing unique to be dumped for a label (ie the
configuration and uberblocks have checksums matching those already
dumped) print nothing for that label.
With additional l's or u's, increase verbosity as follows:
-l Dump each unique configuration only once.
Indicate which labels it appears in.
-ll In addition, dump label space usage stats.
-lll Dump every configuration, unique or not.
-u Dump each unique, valid, uberblock only once.
Indicate which labels it appears in.
-uu In addition, state which slots are invalid.
-uuu Dump every uberblock, unique or not.
-uuuu Dump the uberblock blockpointer (used to be -uuu)
Make exit values conform to the manual page. Failing to unpack a
configuration nvlist is considered an error, as well as failing to open
or read from the device.
Add three tests, zdb_00{3,4,5}_pos to verify the above functionality.
An example of the output:
------------------------------------
LABEL 0
------------------------------------
version: 5000
name: 'pool'
state: 1
txg: 880
< ... redacted ... >
features_for_read:
com.delphix:hole_birth
com.delphix:embedded_data
labels = 0
Uberblock[0]
magic = 0000000000bab10c
version = 5000
txg = 0
guid_sum = 3038694082047428541
timestamp = 1487715500 UTC = Tue Feb 21 14:18:20 2017
labels = 0 1 2 3
Uberblock[4]
magic = 0000000000bab10c
version = 5000
txg = 772
guid_sum = 9045970794941528051
timestamp = 1487727291 UTC = Tue Feb 21 17:34:51 2017
labels = 0
< ... redacted ... >
------------------------------------
LABEL 1
------------------------------------
version: 5000
name: 'pool'
state: 1
txg: 14
< ... redacted ... >
com.delphix:embedded_data
labels = 1 2 3
Uberblock[4]
magic = 0000000000bab10c
version = 5000
txg = 4
guid_sum = 7793930272573252584
timestamp = 1487727521 UTC = Tue Feb 21 17:38:41 2017
labels = 1 2 3
< ... redacted ... >
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5738
If the LED is being accessed by another process when we try to update
it, the update will be lost. Add a retry loop which will read the state
of the LED and update it until the LED is in the correct state. The
number of times this will occur is limited to ensure that the ZEDlet
won't hang ZED.
Refactor to remove duplication so setting of the LED occurs in only one
place.
Cleanup a couple of the warnings generated by shellcheck which weren't
the result of specific choices by the author. Several notes and warnings
are still present but removing them would make the code less clear or
require adding lines to tell shellcheck to ignore the warning.
Remove ",i" from the documentation at the top of the file which appears
to be a typographic error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Christopher Voltz <christopher.voltz@hpe.com>
Closes#5795
Google moved their style guides to GitHub. Update the shell style guide
URL to the new location.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christopher Voltz <christopher.voltz@hpe.com>
Closes#5797
- Pass $VDEV_ENC_SYSFS_PATH to 'zpool [iostat|status] -c' to include
enclosure LED sysfs path.
- Set LEDs correctly after import. This includes clearing any erroniously
set LEDs prior to the import, and setting the LED for any UNAVAIL drives.
- Include symlink for vdev_attach-led.sh in Makefile.am.
- Print the VDEV path in all-syslog.sh, and fix it so the pool GUID actually
prints.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5716Closes#5751
CID 155928: Integer handling issues (DIVIDE_BY_ZERO)
In the current vdev label, the leaf count is always non-zero
but it doesn't hurt to check the count for future proofing.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5749
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Don Brady <don.brady@intel.com>
OpenZFS-issue: https://www.illumos.org/issues/6866
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3e4fae5Closes#5730
Porting Notes:
- Omitted the illumos-specific `/dev/dsk` and `/dev/rdsk`
path conversions since they don't apply on linux.
When dumping the ZFS vdev label with 'zdb -ll', also dump
some nvlist stats to help analyze the current footprint.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5724
This is effectively dead code for the Linux implementation which can
be removed to improve readability. We want to linter to check the
real production/debug build as much as possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5722
This patch adds the necessary infrastructure for ABD to make use
of the vectorized fletcher 4 routines.
- export ABD compatible interface from fletcher_4
- add ABD fletcher_4 tests for data and metadata ABD types.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#5589
There are two cases:
1. if an invalid flag is passed, and
2. if a valid flag is not given a parameter.
In the case of (1), the flag is either short or long. For short flags,
optopt contains the character of the flag. For long, it contains zero,
and we can access the long flag using argv and optind.
In the case of (2), if the flag is short, optopt contains the character
of the flag. If the flag is long, the value in the 4th column of the
long_options table, for that flag, is returned.
We could case over all those values, or we could simply use argv and
optind again.
Note that in the case of something like `--resume`, which is also `-t`,
"t" will be returned if an argument is not provided; so the error
message will say `'t': argument not provided` or similar. This could be
fixed by making it so long and short options don't use the same
character flag, and then combining them in the switch/case statement,
but I didn't think the ugliness of the code would be worth the small
usability enhancement.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7742
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/6d69b40Closes#5702
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes: Moved reference_tracking_enable and
reference_history outside of ZFS_DEBUG.
OpenZFS-issue: https://www.illumos.org/issues/7545
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4dd77f9Closes#5701
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7502
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3c65d1Closes#5677
Porting notes:
- 'zfs_dbgmsg_print()' reintroduced to userspace.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7277
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/29bdd2fCloses#5684
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7163
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f34284dCloses#4484Closes#5661
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: - Matthew Ahrens <mahrens@delphix.com>
Reviewed by: - Paul Dagnelie <pcd@delphix.com>
Approved by: - Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7253
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/754998cCloses#5660
Porting notes:
- Many changes were already made in ZoL (for ex. in d4ed66734).
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6872
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f83b46bCloses#5640
Porting notes:
- Several direct callers of zk_thread_create() are passing TS_RUN for the
length. The `len` and `state` were inverted,this commit fixes them.
Authored by: Eli Rosenthal <eli.rosenthal@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov mail@gmelikov.ru
OpenZFS-issue: https://www.illumos.org/issues/6871
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8fc9228Closes#5621
The local mg variable is unused in non-debug builds.
Wrap the variable in ASSERTV() so that it's only present
in the debug build. Introduced by OpenZFS 7303.
Reviewed-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5616
Porting Notes:
- Many of the fixes proposed by this patch were already applied.
In the cases where a different but equivalent fix was made the
code was updated with the OpenZFS version to minimize differences.
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6550
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c16bcc4Closes#5591
Brian Behlendorf
Prakash Surya
Tom Caputi
LOLi
Sebastien Roy
loli10K
Tony Hutter
Don Brady
Serapheim Dimitropoulos
Gregor Kopka
Serapheim Dimitropoulos
Matthew Ahrens
Paul Dagnelie
Tim Schumacher
bernie1995
Rich Ercolani
Olaf Faaland
DeHackEd
Nathan Lewis
Troels Nørgaard
Low-power
Serapheim Dimitropoulos
kpande
John Gallagher
Antonio Russo
Alek P
Pavel Zakharov
Jorgen Lundman
Paul Dagnelie
Matt Ahrens
Paul Zuchowski
Tomohiro Kusumi
Nasf-Fan
John Eismeier
Scot W. Stevenson
bunder2015
Chunwei Chen
Chris Williamson
Giuseppe Di Natale
Allan Jude
Nathaniel Wesley Filardo
Simon Guest
George G
Jason King
Arkadiusz Bubała
Fabian-Gruenbichler
adisbladis
Tobin Harding
David Quigley
David Quigley
sckobras
Don Brady
Sen Haerens
Ned Bass
Chunwei Chen
George Melikov
Don Brady
Håkan Johansson
Gvozden Neskovic
Dan Kimmel
Richard Yao
Alan Somers
Giuseppe Di Natale
Yuri Pankov
Sydney Vanda
N Clark
Christopher Voltz
