CID 147474: Logically dead code (DEADCODE)
Remove ternary operator and return `error` directly.
Currently return value is derived from a ternary operator. The
conditional is always true. The ternary operator is therefore
redundant i.e dead code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6723
When sending an incremental stream based on a snapshot, the receiving
side must have the same base snapshot. Thus we do not need to send
FREEOBJECTS records for any objects past the maximum one which exists
locally.
This allows us to send incremental streams (again) to older ZFS
implementations (e.g. ZoL < 0.7) which actually try to free all objects
in a FREEOBJECTS record, instead of bailing out early.
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#5699Closes#6507Closes#6616
All objects after the last written or freed object are not supposed to
exist after receiving the stream. Free them accordingly, as if a
freeobjects record for them had been included in the stream.
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#5699Closes#6507Closes#6616
With the addition of the ABD changes consumption of the virtual
address space has been greatly reduced. This exposed an issue on
CONFIG_HIGHMEM systems where free memory was being calculated
incorrectly. Functionally this didn't cause any major problems
prior to ABD because a lack of available virtual address space
was used as an indicator of low memory.
This patch makes the following changes to address the issue and
in the process realigns the code further with OpenZFS. There
are no substantive changes in behavior for 64-bit systems.
* Added CONFIG_HIGHMEM case to the arc_all_memory() and
arc_free_memory() functions to only consider low memory pages
on CONFIG_HIGHMEM systems.
* The arc_free_memory() function was updated to return bytes
instead of pages to be consistent with the other helper
functions. In user space we make up some reasonable values
since currently only testing is performed in this context.
* Adds three new values to the arcstats kstat to provide visibility
in to the ARC's assessment of the memory situation:
memory_all_bytes, memory_free_bytes, and memory_available_bytes.
* Added kmem_reap() call to arc_available_memory() for 32-bit
builds to realign code with OpenZFS.
* Reduced size of test file in /async_destroy_001_pos.ksh to
speed up test case. Multiple txgs are still required.
* Move vdevs used by zpool_clear_001_pos and zpool_upgrade_002_pos
to TEST_BASE_DIR location to speed up test cases.
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5352Closes#6734
When decrementing the struct_size and scatter_chunk_waste kstats
the value needs to be cast to an int on 32-bit systems.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6721
Currently `if` statement includes an assignment (from a function return
value) and a equality check. The parenthesis are in the incorrect place,
currently the code clobbers the function return value because of this.
We can fix this by simplifying the `if` statement.
`if (foo != 0)`
can be more succinctly expressed as
`if (foo)`
Remove the equality check, add parenthesis to correct the statement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Closes#6685Close#6719
The vdev_copy_uberblocks() function should use abd_alloc_linear() to
allocate ub_abd, because abd_to_buf(ub_abd)) is used later.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#6718Closes#6713
The avl_update_* functions are never used by ZFS and are therefore
being removed. They're barely even used in Illumos. Additionally,
simplify avl_add() by using a VERIFY which produces exactly the same
behavior under Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6716
When receiving a FREEOBJECTS record, receive_freeobjects()
incorrectly skips a freed object in some cases. Specifically, this
happens when the first object in the range to be freed doesn't exist,
but the second object does. This leaves an object allocated on disk
on the receiving side which is unallocated on the sending side, which
may cause receiving subsequent incremental streams to fail.
The bug was caused by an incorrect increment of the object index
variable when current object being freed doesn't exist. The
increment is incorrect because incrementing the object index is
handled by a call to dmu_object_next() in the increment portion of
the for loop statement.
Add test case that exposes this bug.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6694Closes#6695
It's often useful to have access to txg history for debugging
purposes. This patch changes the default from 0 to 100 TXGs
worth of history preserved.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6691
Commit d3c2ae1 introduced a dbuf cache with a default size of the
minimum of 100M or 1/32 maximum ARC size. (These figures may be adjusted
using dbuf_cache_max_bytes and dbuf_cache_max_shift.) The dbuf cache
is counted as metadata for the purposes of ARC size calculations.
On a 1GB box the ARC maximum size defaults to c_max 493M which gives a
dbuf cache default minimum size of 15.4M, and the ARC metadata defaults
to minimum 16M. I.e. the dbuf cache is an significant proportion of the
minimum metadata size. With other overheads involved this actually means
the ARC metadata doesn't get down to the minimum.
This patch dynamically scales the dbuf cache to the target ARC size
instead of statically scaling it to the maximum ARC size. (The scale is
still set by dbuf_cache_max_shift and the maximum size is still fixed by
dbuf_cache_max_bytes.) Using the target ARC size rather than the current
ARC size is done to help the ARC reach the target rather than simply
focusing on the current size.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #6506Closes#6561
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6672
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#652Closes#651
Rename it as mmp_random_leaf() since it is defined in mmp.c.
The earlier implementation could end up spinning forever if a pool had a
vdev marked writeable, none of whose children were writeable. It also
did not guarantee that if a writeable leaf vdev existed, it would be
found.
Reimplement to recursively walk the device tree to select the leaf. It
searches the entire tree, so that a return value of (NULL) indicates
there were no usable leaves in the pool; all were either not writeable
or had pending mmp writes.
It still chooses the starting child randomly at each level of the tree,
so if the pool's devices are healthy, the mmp writes go to random leaves
with an even distribution. This was verified by testing using
zfs_multihost_history enabled.
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6631Closes#6665
Increase the default arc_c_min value to which whichever is larger,
either 32M or 1/32 of total system memory. This is advantageous for
systems with more than 1G of memory where performance issues may
occur when the ARC is allowed to collapse below a minimum size.
At the same time we want to use the bare minimum value which is
still functional so the filesystem can be used in very low memory
environments.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6659
This symbol is needed by Lustre for the same reason it was needed
by the ZPL. It should have been exported when the original patch
was merged.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alex Zhuravlev <bzzz@whamcloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6660
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Feng Sun <loyou85@gmail.com>
Closes#6658
ZFS buildbot STYLE builder was moved to Ubuntu 17.04
which has a newer version of cppcheck. Handle the
new cppcheck errors.
uu_* functions removed in this commit were unused
and effectively dead code. They are now retired.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6653
generic_start_io_acct/generic_end_io_acct in the master
branch of the linux kernel requires that the request_queue
be provided.
Move the logic from freemem in the spl to arc_free_memory
in arc.c. Do this so we can take advantage of global_page_state
interface checks in zfs.
Upstream kernel replaced struct block_device with
struct gendisk in struct bio. Determine if the
function bio_set_dev exists during configure
and have zfs use that if it exists.
bio_set_dev https://github.com/torvalds/linux/commit/74d4699
global_node_page_state https://github.com/torvalds/linux/commit/75ef718
io acct https://github.com/torvalds/linux/commit/d62e26b
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6635
Changing any metadata, should modify the ctime.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#3644Closes#6586
On pool import when the old cache file is removed
the ereport.fs.zfs.config_cache_write event is generated.
Because zpool export always removes cache file it happens
every export - import sequence.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6617
The portion of the zvol_replay_write() handler responsible for
replaying indirect log records for some reason never existed.
As a result indirect log records were not being correctly replayed.
This went largely unnoticed since the majority of zvol log records
were of the type WR_COPIED or WR_NEED_COPY prior to OpenZFS 7578.
This patch updates zvol_replay_write() to correctly handle these
log records and adds a new test case which verifies volume replay
to prevent any regression. The existing test case which verified
replay on filesystem was renamed slog_replay_fs.ksh for clarity.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6603Closes#6615
This reverts commit 65dcb0f67a until
a comprehensive fix is finalized. The stricter interior dnode
detection in 4c5b89f59e and the new
test case added by this patch revealed a issue with resizing
dnodes when receiving an incremental backup stream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6576
Refactor dmu_object_alloc_dnsize() and dnode_hold_impl() to simplify the
code, fix errors introduced by commit dbeb879 (PR #6117) interacting
badly with large dnodes, and improve performance.
* When allocating a new dnode in dmu_object_alloc_dnsize(), update the
percpu object ID for the core's metadnode chunk immediately. This
eliminates most lock contention when taking the hold and creating the
dnode.
* Correct detection of the chunk boundary to work properly with large
dnodes.
* Separate the dmu_hold_impl() code for the FREE case from the code for
the ALLOCATED case to make it easier to read.
* Fully populate the dnode handle array immediately after reading a
block of the metadnode from disk. Subsequently the dnode handle array
provides enough information to determine which dnode slots are in use
and which are free.
* Add several kstats to allow the behavior of the code to be examined.
* Verify dnode packing in large_dnode_008_pos.ksh. Since the test is
purely creates, it should leave very few holes in the metadnode.
* Add test large_dnode_009_pos.ksh, which performs concurrent creates
and deletes, to complement existing test which does only creates.
With the above fixes, there is very little contention in a test of about
200,000 racing dnode allocations produced by tests 'large_dnode_008_pos'
and 'large_dnode_009_pos'.
name type data
dnode_hold_dbuf_hold 4 0
dnode_hold_dbuf_read 4 0
dnode_hold_alloc_hits 4 3804690
dnode_hold_alloc_misses 4 216
dnode_hold_alloc_interior 4 3
dnode_hold_alloc_lock_retry 4 0
dnode_hold_alloc_lock_misses 4 0
dnode_hold_alloc_type_none 4 0
dnode_hold_free_hits 4 203105
dnode_hold_free_misses 4 4
dnode_hold_free_lock_misses 4 0
dnode_hold_free_lock_retry 4 0
dnode_hold_free_overflow 4 0
dnode_hold_free_refcount 4 57
dnode_hold_free_txg 4 0
dnode_allocate 4 203154
dnode_reallocate 4 0
dnode_buf_evict 4 23918
dnode_alloc_next_chunk 4 4887
dnode_alloc_race 4 0
dnode_alloc_next_block 4 18
The performance is slightly improved for concurrent creates with
16+ threads, and unchanged for low thread counts.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5396Closes#6522Closes#6414Closes#6564
When receiving an incremental backup stream, call
dmu_object_reclaim_dnsize() if an object's dnode size differs between
the incremental source and target. Otherwise it may appear that a
dnode which has shrunk is still occupying slots which are in fact
free. This will cause a failure to receive new objects that should
occupy the now-free slots.
Add a test case to verify that an incremental stream containing
objects with changed dnode sizes can be received without error. This
test case fails without this change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6366Closes#6576
Add a helper function to trim the tailing new line. While we're
here use this new hook to immediately apply the new scheduler.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3356Closes#6573
Add a small wrapper around libzfs_core`lzc_send_space() to libzfs so
that every legacy ZFS_IOC_SEND consumer, along with their userland
counterpart estimate_ioctl(), can leverage ZFS_IOC_SEND_SPACE to
request send space estimation.
The legacy functionality in zfs_ioc_send() is left untouched for
compatibility purposes.
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6029
Authored by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Andy Stormont <andyjstormont@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2976
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5c5f137Closes#6582
Authored by: Eli Rosenthal <eli.rosenthal@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7028
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/86f617eCloses#6583
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7261
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/48dd5e6Closes#6579
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8375
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/843c211Closes#6578
Fix a few nits in the comments from large dnodes. Also import
some of the commit message as a comment in the code, making
it more accessible.
Reviewed-by: @rottegift
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matt Ahrens <mahrens@delphix.com>
Closes#6551
vm_node_stat must be used instead of vm_zone_stat. Unfortunately the
old code still compiles potentially leading to silent failure of
arc_evictable_memory()
AKAMAI: CR 3816601: Regression in zfs dropcache test
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6528
Remove harmless duplicate multilist_link_init() introduced by
commit d3c2ae1.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#6552
This patch fixes several issues discovered after
the encryption patch was merged:
* Fixed a bug where encrypted datasets could attempt
to receive embedded data records.
* Fixed a bug where dirty records created by the recv
code wasn't properly setting the dr_raw flag.
* Fixed a typo where a dmu_tx_commit() was changed to
dmu_tx_abort()
* Fixed a few error handling bugs unrelated to the
encryption patch in dmu_recv_stream()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6512Closes#6524Closes#6545
Use fnvlist on user input would allow user to easily panic zfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6529
vdev_queue:
- Track the last position of each vdev, including the io size,
in order to detect linear access of the following zio.
- Remove duplicate `vq_lastoffset`
vdev_mirror:
- Correctly calculate the zio offset (signedness issue)
- Deprecate `vdev_queue_register_lastoffset()`
- Add `VDEV_LABEL_START_SIZE` to zio offset of leaf vdevs
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#6461
Since OpenZFS 7578 (1b7c1e5) if we have a ZVOL with logbias=throughput
we will force WR_INDIRECT itxs in zvol_log_write() setting itx->itx_lr
offset and length to the offset and length of the BIO from
zvol_write()->zvol_log_write(): these offset and length are later used
to take a range lock in zillog->zl_get_data function: zvol_get_data().
Now suppose we have a ZVOL with blocksize=8K and push 4K writes to
offset 0: we will only be range-locking 0-4096. This means the
ASSERTion we make in dbuf_unoverride() is no longer valid because now
dmu_sync() is called from zilog's get_data functions holding a partial
lock on the dbuf.
Fix this by taking a range lock on the whole block in zvol_get_data().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6238Closes#6315Closes#6356Closes#6477
It's not enough to preserve/restore MS_RDONLY on the superblock flags
to avoid remounting a snapshot read-write: be explicit about our
intentions to the VFS layer so the readonly bit is updated correctly
in do_remount_sb().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6510Closes#6515
* Removed zpios kmod, utility, headers and man page.
* Removed unused scripts zpios-profile/*, zpios-test/*,
zpool-config/*, smb.sh, zpios-sanity.sh, zpios-survey.sh,
zpios.sh, and zpool-create.sh.
* Removed zfs-script-config.sh.in. When building 'make' generates
a common.sh with in-tree path information from the common.sh.in
template. This file and sourced by the test scripts and used
for in-tree testing, it is not included in the packages. When
building packages 'make install' uses the same template to
create a new common.sh which is appropriate for the packaging.
* Removed unused functions/variables from scripts/common.sh.in.
Only minimal path information and configuration environment
variables remain.
* Removed unused scripts from scripts/ directory.
* Remaining shell scripts in the scripts directory updated to
cleanly pass shellcheck and added to checked scripts.
* Renamed tests/test-runner/cmd/ to tests/test-runner/bin/ to
match install location name.
* Removed last traces of the --enable-debug-dmu-tx configure
options which was retired some time ago.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6509
Added a 'corrupt' error option that will flip a bit in the data
after a read operation. This is useful for generating checksum
errors at the device layer (in a mirror config for example). It
is also used to validate the diagnosis of checksum errors from
the zfs diagnosis engine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6345
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
When doing read on a file open with O_SYNC, it will trigger zil_commit.
However for snapshot, there's no zil, so we shouldn't be doing that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6478Closes#6494
The pool name can be 256 chars long. Today, in /proc/spl/kstat/zfs/
the name is limited to < 32 characters. This change is to allows
bigger pool names.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#6481
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#641
* Simplify threads, mutexs, cvs and rwlocks
* Update the zk_thread_create() function to use the same trick
as Illumos. Specifically, cast the new pthread_t to a void
pointer and return that as the kthread_t *. This avoids the
issues associated with managing a wrapper structure and is
safe as long as the callers never attempt to dereference it.
* Update all function prototypes passed to pthread_create() to
match the expected prototype. We were getting away this with
before since the function were explicitly cast.
* Replaced direct zk_thread_create() calls with thread_create()
for code consistency. All consumers of libzpool now use the
proper wrappers.
* The mutex_held() calls were converted to MUTEX_HELD().
* Removed all mutex_owner() calls and retired the interface.
Instead use MUTEX_HELD() which provides the same information
and allows the implementation details to be hidden. In this
case the use of the pthread_equals() function.
* The kthread_t, kmutex_t, krwlock_t, and krwlock_t types had
any non essential fields removed. In the case of kthread_t
and kcondvar_t they could be directly typedef'd to pthread_t
and pthread_cond_t respectively.
* Removed all extra ASSERTS from the thread, mutex, rwlock, and
cv wrapper functions. In practice, pthreads already provides
the vast majority of checks as long as we check the return
code. Removing this code from our wrappers help readability.
* Added TS_JOINABLE state flag to pass to request a joinable rather
than detached thread. This isn't a standard thread_create() state
but it's the least invasive way to pass this information and is
only used by ztest.
TEST_ZTEST_TIMEOUT=3600
Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4547Closes#5503Closes#5523Closes#6377Closes#6495
If fault injection is enabled, the ZIO_FLAG_IO_RETRY could be set by
zio_handle_device_injection() to generate the FMA events and update
stats. Hence, ignore the flag and process such zios.
A better fix would be to add another flag in the zio_t to indicate that
the zio is failed because of a zinject rule. However, considering the
fact that we do this in debug bits, we could do with the crude check
using the global flag zio_injection_enabled which is set to 1 when
zinject records are added.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Closes#6383Closes#6384
This was probably accidentally committed in
aeb9baa618
Fix: handle NULL case in spl_kmem_free_track()
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#644
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Acquire zv_suspend_lock on first open and last close only.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#6342
Log contents of a receive record if an error occurs while writing
it out to the pool. This may help determine the cause when backup
streams are rejected as invalid.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6465
When performing concurrent object allocations using the new
multi-threaded allocator and large dnodes it's possible to
allocate overlapping large dnodes.
This case should have been handled by detecting an error
returned by dnode_hold_impl(). But that logic only checked
the returned dnp was not-NULL, and the dnp variable was not
reset to NULL when retrying. Resolve this issue by properly
checking the return value of dnode_hold_impl().
Additionally, it was possible that dnode_hold_impl() would
misreport a dnode as free when it was in fact in use. This
could occurs for two reasons:
* The per-slot zrl_lock must be held over the entire critical
section which includes the alloc/free until the new dnode
is assigned to children_dnodes. Additionally, all of the
zrl_lock's in the range must be held to protect moving
dnodes.
* The dn->dn_ot_type cannot be solely relied upon to check
the type. When allocating a new dnode its type will be
DMU_OT_NONE after dnode_create(). Only latter when
dnode_allocate() is called will it transition to the new
type. This means there's a window when allocating where
it can mistaken for a free dnode.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6414Closes#6439
taskq work item to more than one queue concurrently. Also, please
see discussion in zfsonlinux/zfs#3840.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#609
taskq_seq_show_impl walks the tq_active_list to show the tqent_func and
tqent_arg. However for taskq_dispatch_ent, it's very likely that the
task entry will be freed during the function call, and causes a
use-after-free bug.
To fix this, we duplicate the task entry to an on-stack struct, and
assign it instead to tqt_task. This way, the tq_lock alone will
guarantee its safety.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#638Closes#640
gcc-7 seems to use __udivmoddi4 for 64-bit division on 32-bit arch. This
patch implement them so we don't get undefined reference error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes zfsonlinux/zfs#6417
Closes#636
Update many return and assignment statements to follow the convention
of using the SET_ERROR macro when returning a hard-coded non-zero
value from a function. This aids debugging by recording the error
codes in the debug log.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6441
While investigating https://github.com/zfsonlinux/zfs/issues/6425 I
noticed that ioctl ZIOs were not setting zio->io_delay correctly. They
would set the start time in zio_vdev_io_start(), but never set the end
time in zio_vdev_io_done(), since ioctls skip it and go straight to
zio_done(). This was causing spurious "delayed IO" events to appear,
which would eventually get rate-limited and displayed as
"Missed events" messages in zed.
To get around the problem, this patch only sets zio->io_delay for read
and write ZIOs, since that's all we care about anyway.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6425Closes#6440
At import time spa_import() calls zvol_create_minors() directly: with
the current implementation we have no way to avoid device node
creation when volmode=none.
Fix this by enforcing volmode=none directly in zvol_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6426
If we are in the middle of an incremental 'zfs receive', the child
.../%recv will exist. If we run 'zfs promote' .../%recv, it will "work",
but then zfs gets confused about the status of the new dataset.
Attempting to do this promote should be an error.
Similarly renaming .../%recv datasets should not be allowed.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#4843Closes#6339
Redefine the SET_ERROR macro in terms of __dprintf() so the error
return codes get logged as both tracepoint events (if tracepoints are
enabled) and as ZFS debug log entries. This also allows us to use
the same definition of SET_ERROR() in kernel and user space.
Define a new debug flag ZFS_DEBUG_SET_ERROR=512 that may be bitwise
or'd into zfs_flags. Setting this flag enables both dprintf() and
SET_ERROR() messages in the debug log. That is, setting
ZFS_DEBUG_SET_ERROR and ZFS_DEBUG_DPRINTF|ZFS_DEBUG_SET_ERROR are
equivalent (this was done for sake of simplicity). Leaving
ZFS_DEBUG_SET_ERROR unset suppresses the SET_ERROR() messages which
helps avoid cluttering up the logs.
To enable SET_ERROR() logging, run:
echo 1 > /sys/module/zfs/parameters/zfs_dbgmsg_enable
echo 512 > /sys/module/zfs/parameters/zfs_flags
Remove the zfs_set_error_class tracepoints event class since
SET_ERROR() now uses __dprintf(). This sacrifices a bit of
granularity when selecting individual tracepoint events to enable but
it makes the code simpler.
Include file, function, and line number information in debug log
entries. The information is now added to the message buffer in
__dprintf() and as a result the zfs_dprintf_class tracepoints event
class was changed from a 4 parameter interface to a single parameter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6400
In unattended operations it's often more useful to have node
panic and reboot when it encounters problems as opposed to
sit there indefinitely waiting for somebody to discover it.
This implements an spl_panic_crash module parameter, set it
to nonzero to cause spl_panic() to call panic().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Closes#634
Check in the DMU whether an object record in a send stream being
received contains an unsupported dnode slot count, and return an
error if it does. Failure to catch an unsupported dnode slot count
would result in a panic when the SPA attempts to increment the
reference count for the large_dnode feature and the pool has the
feature disabled. This is not normally an issue for a well-formed
send stream which would have the DMU_BACKUP_FEATURE_LARGE_DNODE flag
set if it contains large dnodes, so it will be rejected as
unsupported if the required feature is disabled. This change adds a
missing object record field validation.
Add missing stream feature flag checks in
dmu_recv_resume_begin_check().
Consolidate repetitive comment blocks in dmu_recv_begin_check().
Update zstreamdump to print the dnode slot count (dn_slots) for an
object record when running in verbose mode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6396
'zpool clear' should be able to resume I/O on suspended, but otherwise
healthy, pools.
4a283c7 accidentally introduced a new code path where we call
txg_wait_synced() on the suspended pool before we had the chance to
resume I/O via zio_resume(): this results in the 'zpool clear'
command hanging indefinitely, waiting for a TXG that cannot be synced.
Fix this by avoiding the call to txg_wait_synced().
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6399
There is no need to perform the activity check before detecting that the
user must set the system hostid, because the pool's multihost property
is on, but spa_get_hostid() returned 0. The initial call to
vdev_uberblock_load() provided the information required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388
Add a callback to wake all running mmp threads when
zfs_multihost_interval is changed.
This is necessary when the interval is changed from a very large value
to a significantly lower one, while pools are imported that have the
multihost property enabled.
Without this commit, the mmp thread does not wake up and detect the new
interval until after it has waited the old multihost interval time. A
user monitoring mmp writes via the provided kstat would be led to
believe that the changed setting did not work.
Added a test in the ZTS under mmp to verify the new functionality is
working.
Added a test to ztest which starts and stops mmp threads, and calls into
the code to signal sleeping mmp threads, to test for deadlocks or
similar locking issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6387
The config lock must be held for the duration of the MMP write.
Since the I/Os are executed via map_nowait(), the done function
is the only place where we know the write has completed.
Since SCL_STATE is taken as reader, overlapping I/Os do not
create a deadlock. The refcount is simply increased when new
I/Os are queued and decreased when I/Os complete.
Test case added which exercises the probe IO call path to
verify the fix and prevent a regression.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6394
This reverts commit cc9c6bc, which has been causing intermittent
test failures on buildbot. A correct fix for this locking issue
has been applied in a separate patch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
If we're creating a pool with version >= SPA_VERSION_DSL_SCRUB (v11)
we need to account for additional space needed by the origin dataset
which will also be snapshotted: "poolname"+"/"+"$ORIGIN"+"@"+"$ORIGIN".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6374
Commit 379ca9c Multi-modifier protection (MMP) used HZ to convert
nanoseconds to ticks for use with cv_timedwait() and ddi_get_lbolt().
The correct macro is hz, which is defined within the SPL for kernel
space, and within zfs_context.h for user space.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6357Closes#6360
CID 165755: Division or modulo by zero (DIVIDE_BY_ZERO)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6352
When we load a ZFS pool having spa_name equals to some existing kstat
we would have to create a duplicate entry, which procfs doesn't like.
For instance a ZFS pool named "zil" would have its kstat "txgs"
(module "zfs/zil") intalled under "/proc/spl/kstat/zfs/zil":
unfortunately we already have a kstat named "zil" (module "zfs")
installed in the same procfs location.
Avoid this issue by skipping the duplicate entry creation in procfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#628
Commit torvalds/linux@4e4cbee9. The bio->bi_error field was
replaced with bio->bi_status which is an enum that describes
all possible error types.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6351
When an IO fails then zio_vdev_io_done() can call vdev_probe()
to determine the health of the vdev. This is safe as long as
the original zio was submitted with zio_wait() and holds the
SCL_STATE_ALL lock over the operation.
If zio_no_wait() was used then the done callback will submit
the probe IO outside the SCL_STATE_ALL lock and hit this
ASSERT in zio_create()
ASSERT(!vd || spa_config_held(spa, SCL_STATE_ALL, RW_READER));
Resolve the issue by only allowing vdev_probe() to be called
when there's a waiter indicating the caller is using zio_wait().
This assumes that caller is still holding SCL_STATE_ALL.
This issue isn't MMP specific but was surfaced when testing.
Without this patch it can be reproduced by running:
zpool set multihost on <pool>
zinject -d <vdev> -e io -T write -f 50 <pool> -L uber
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#745Closes#6279
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
Historically the SPL cached the system hostid the first time it
was accessed. This was done to speed up subsequent accesses.
But in practice the system host id is rarely accessed and its
inconvenient that it doesn't promptly detect /etc/hostid
configuration changes. Therefore, zone_get_hostid() has been
updated to always refresh the system hostid reported.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#626
Authored by: Dave Eddy <dave@daveeddy.com>
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Joshua M. Clulow <jmc@joyent.com>
Reviewed by: Josh Wilsdon <jwilsdon@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Alan Somers <asomers@gmail.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6939
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ce1577bCloses#6328
The volmode property may be set to control the visibility of ZVOL
block devices.
This allow switching ZVOL between three modes:
full - existing fully functional behaviour (default)
dev - hide partitions on ZVOL block devices
none - not exposing volumes outside ZFS
Additionally the new zvol_volmode module parameter can be used to
control the default behaviour.
This functionality can be used, for instance, on "backup" pools to
avoid cluttering /dev with unneeded zd* devices.
Original-patch-by: mav <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
FreeBSD-commit: https://github.com/freebsd/freebsd/commit/dd28e6bbCloses#1796Closes#3438Closes#6233
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
* All hunks unrelated to ZFS were dropped.
OpenZFS-issue: https://www.illumos.org/issues/5428
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4585130Closes#6326
The sync thread is concurrently modifying dn_phys->dn_nlevels
while dbuf_dirty() is trying to assert something about it, without
holding the necessary lock. We need to move this assertion further down
in the function, after we have acquired the dn_struct_rwlock.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8126
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0ef125dCloses#6314
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8067
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8173085Closes#6319
Illumos 4080 inadvertently allows 'zpool clear' on readonly pools: fix
this by reintroducing a check (POOL_CHECK_READONLY) in zfs_ioc_clear
registration code.
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6306
Currently, there is no way to pause a scrub. Pausing may
be useful when the pool is busy with other I/O to preserve
bandwidth.
This patch adds the ability to pause and resume scrubbing.
This is achieved by maintaining a persistent on-disk scrub state.
While the state is 'paused' we do not scrub any more blocks.
We do however perform regular scan housekeeping such as
freeing async destroyed and deadlist blocks while paused.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Serapheim Dimitropoulos <serapheimd@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6167
On the single core machine the system may hang when the
spa_namespare_lock acquisition fails in the zvol_first_open
function. It returns -ERESTARTSYS error what causes the
endless loop in __blkdev_get function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6283Closes#6312
Clang doesn't support `/` as comment in assembly, this patch replaces
them with `#`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Leorize <alaviss@users.noreply.github.com>
Closes#6311
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The problem is that zfs_get_data() supplies a stale zgd_bp to
dmu_sync(), which we then nopwrite against.
zfs_get_data() doesn't hold any DMU-related locks, so after it
copies db_blkptr to zgd_bp, dbuf_write_ready() could change
db_blkptr, and dbuf_write_done() could remove the dirty record.
dmu_sync() then sees the stale BP and that the dbuf it not dirty,
so it is eligible for nop-writing.
The fix is for dmu_sync() to copy db_blkptr to zgd_bp after
acquiring the db_mtx. We could still see a stale db_blkptr,
but if it is stale then the dirty record will still exist and
thus we won't attempt to nopwrite.
OpenZFS-issue: https://www.illumos.org/issues/8378
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3127742Closes#6293
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The existing kernel-side code only provides a method to rollback to a
latest snapshot, whatever it happens to be at the time when the rollback
is actually done. That could be unsafe or confusing in environments
where concurrent DSL changes are possible as the resulting state could
correspond to a newer or older snapshot than the originally requested
one.
This change allows to amend that method such that the rollback is
performed only when the latest snapshot has a specific name. That is,
if a new snapshot is concurrently created or the target snapshot is
destroyed, then no rollback is done and EXDEV error is returned.
New libzfs_core function lzc_rollback_to() is provided for the new
functionality. libzfs is changed to use lzc_rollback_to() to implement
zfs rollback command.
Perhaps we should return different errors to distinguish the case where
the desired snapshot exists but it's not the latest snapshot and the
case where the desired snapshot does not exist.
OpenZFS-issue: https://www.illumos.org/issues/7600
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3d645ebCloses#6292
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7910
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cb6af4bCloses#6291
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The problem is that when dsl_bookmark_destroy_check() is
executed from open context (the pre-check), it fills in
dbda_success based on the existence of the bookmark. But
the bookmark (or containing filesystem as in this case)
can be destroyed before we get to syncing context. When
we re-run dsl_bookmark_destroy_check() in syncing context,
it will not add the deleted bookmark to dbda_success,
intending for dsl_bookmark_destroy_sync() to not process
it. But because the bookmark is still in dbda_success from
the open-context call, we do try to destroy it.
The fix is that dsl_bookmark_destroy_check() should not
modify dbda_success when called from open context.
OpenZFS-issue: https://www.illumos.org/issues/8377
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b0b6fe3Closes#6286
Resolves issues discovered when porting to OpenZFS.
* Lint warnings.
* Made dnode_move_impl() large dnode aware. This
functionality is currently unused on Linux.
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6262
Make zfs_arc_meta_limit_percent and zfs_arc_dnode_limit_percent behave
as you would expect from zfs-module-parameters.5.
- recalculate arc_meta_limit if zfs_arc_meta_limit_percent changes
- recalculate arc_dnode_limit if zfs_arc_dnode_limit_percent changes
- correctly set arc_meta_limit and arc_dnode_limit if zfs_arc_max or
zfs_arc_meta_min changes
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#6269
GCC 7.1 with will warn when we're not checking the snprintf()
return code in cases where the buffer could be truncated. This
patch either checks the snprintf return code (where applicable),
or simply disables the warnings (ztest.c).
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6253
Commit 8542ef8 allowed optional IOs to be aggregated beyond
the specified aggregation limit. Since the aggregation limit
was also used to enforce the maximum block size, setting
`zfs_vdev_aggregation_limit=16777216` could result in an
attempt to allocate an ABD larger than 16M.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6259Closes#6270
Use zv_state_lock to protect all members of zvol_state structure, add
relevant ASSERT()s. Take zv_suspend_lock before zv_state_lock, do not
hold zv_state_lock across suspend/resume.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#6226
In bqueue_dequeue(), call cv_signal() with bq_lock held.
Re-enable rsend_009_pos to test the fix.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#5887
In zfs/dmu_object and icp/core/kcf_sched, the CPU_SEQID macro
should be surrounded by `kpreempt_disable` and `kpreempt_enable`
calls to avoid a Linux kernel BUG warning. These code paths use
the cpuid to minimize lock contention and is is safe to reschedule
the process to a different processor at any time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Morgan Jones <me@numin.it>
Closes#6239
In the original form of device error injection, it was an all or nothing
situation. To help simulate intermittent error conditions, you can now
specify a real number percentage value. This is also very useful for our
ZFS fault diagnosis testing and for injecting intermittent errors during
load testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#6227
Use queue_flag_set_unlocked() in zvol_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Issue #6226
This continues what was started in
0eef1bde31 by fully converting zvols
to avoid unnecessary dnode_hold() calls. This saves a small amount
of CPU time and slightly improves latencies of operations on zvols.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@prophetstor.com>
Closes#6058
Buildbots and zfs-tests regularly see 7 kilobytes of stack
usage with this function. Convert self-calls to iterations
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#6219
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
The send size estimate for a zvol can be too low, if the size of the
record headers (dmu_replay_record_t's) is a significant portion of the
size. This is typically the case when the data is highly compressible,
especially with embedded blocks.
The problem is that dmu_adjust_send_estimate_for_indirects() assumes
that blocks are the size of the "recordsize" property (128KB). However,
for zvols, the blocks are the size of the "volblocksize" property (8KB).
Therefore, we estimate that there will be 16x less record headers than
there really will be.
The fix is to check the type of the object set (whether it is a zvol or
not) and pick the appropriate property. In addition, while we are at it,
we also add the size of the BEGIN and END records to the estimate.
OpenZFS-issue: https://www.illumos.org/issues/8056
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/faf09cdCloses#6205
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
dbuf_evict_notify() holds the dbuf_evict_lock while checking if it should
do the eviction itself (because the evict thread is not able to keep up).
This can result in massive lock contention. It isn't necessary to hold
the lock, because if we make the wrong choice occasionally, nothing bad
will happen. This commit results in a ~60% performance improvement for
ARC-cached sequential reads.
OpenZFS-issue: https://www.illumos.org/issues/8156
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f73e5d9Closes#6204
dmu_object_alloc() is single-threaded, so when multiple threads are
creating files in a single filesystem, they spend a lot of time waiting
for the os_obj_lock. To improve performance of multi-threaded file
creation, we must make dmu_object_alloc() typically not grab any
filesystem-wide locks.
The solution is to have a "next object to allocate" for each CPU. Each
of these "next object"s is in a different block of the dnode object, so
that concurrent allocation holds dnodes in different dbufs. When a
thread's "next object" reaches the end of a chunk of objects (by default
4 blocks worth -- 128 dnodes), it will be reset to the per-objset
os_obj_next, which will be increased by a chunk of objects (128). Only
when manipulating the os_obj_next will we need to grab the os_obj_lock.
This decreases lock contention dramatically, because each thread only
needs to grab the os_obj_lock briefly, once per 128 allocations.
This results in a 70% performance improvement to multi-threaded object
creation (where each thread is creating objects in its own directory),
from 67,000/sec to 115,000/sec, with 8 CPUs.
Work sponsored by Intel Corp.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8199
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/374Closes#4703Closes#6117
- After some ZIL changes 6 years ago zil_slog_limit got partially broken
due to zl_itx_list_sz not updated when async itx'es upgraded to sync.
Actually because of other changes about that time zl_itx_list_sz is not
really required to implement the functionality, so this patch removes
some unneeded broken code and variables.
- Original idea of zil_slog_limit was to reduce chance of SLOG abuse by
single heavy logger, that increased latency for other (more latency critical)
loggers, by pushing heavy log out into the main pool instead of SLOG. Beside
huge latency increase for heavy writers, this implementation caused double
write of all data, since the log records were explicitly prepared for SLOG.
Since we now have I/O scheduler, I've found it can be much more efficient
to reduce priority of heavy logger SLOG writes from ZIO_PRIORITY_SYNC_WRITE
to ZIO_PRIORITY_ASYNC_WRITE, while still leave them on SLOG.
- Existing ZIL implementation had problem with space efficiency when it
has to write large chunks of data into log blocks of limited size. In some
cases efficiency stopped to almost as low as 50%. In case of ZIL stored on
spinning rust, that also reduced log write speed in half, since head had to
uselessly fly over allocated but not written areas. This change improves
the situation by offloading problematic operations from z*_log_write() to
zil_lwb_commit(), which knows real situation of log blocks allocation and
can split large requests into pieces much more efficiently. Also as side
effect it removes one of two data copy operations done by ZIL code WR_COPIED
case.
- While there, untangle and unify code of z*_log_write() functions.
Also zfs_log_write() alike to zvol_log_write() can now handle writes crossing
block boundary, that may also improve efficiency if ZPL is made to do that.
Sponsored by: iXsystems, Inc.
Authored by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7578
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aeb13acCloses#6191
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
When writing pre-compressed buffers, arc_write() requires that
the compression algorithm used to compress the buffer matches
the compression algorithm requested by the zio_prop_t, which is
set by dmu_write_policy(). This makes dmu_write_policy() and its
callers a bit more complicated.
We simplify this by making arc_write() trust the caller to supply
the type of pre-compressed buffer that it wants to write,
and override the compression setting in the zio_prop_t.
OpenZFS-issue: https://www.illumos.org/issues/8155
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b55ff58Closes#6200
Since torvalds/linux@d0a5b99 IOP_XATTR is used to indicate the inode
has xattr support: clear it for the ctldir inodes to avoid EIO errors.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6189
When inheriting the "snapdev" property to we don't always call
zfs_prop_set_special(): this prevents device nodes from being created in
certain situations. Because "snapdev" is the only *special* property
that is also inheritable we need to call zfs_prop_set_special() even
when we're not reverting it to the received value ('zfs inherit -S').
Additionally, fix a NULL pointer dereference accidentally introduced in
5559ba0 that can be triggered when setting the "snapdev" property to
the value "hidden" twice.
Finally, add a new test case "zvol_misc_snapdev" to the ZFS Test Suite.
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6131Closes#6175Closes#6176
If, for example, your aux device was /dev/sdc, but now the aux device is
removed and /dev/sdc points to other device. zpool import will still
use that device and corrupt it.
The problem is that the spa_validate_aux in spa_import, rather than
validate the on-disk label, it would actually write label to disk. We
remove them since spa_load_{spares,l2cache} seems to do everything we
need and they would actually validate on-disk label.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6158
Move kmem_free() so it's called for every error path: this is
preferred over making `dmu_object_info_t doi` local to accommodate
older kernels with limited stacks.
Reviewed by: Boris Protopopov <bprotopopov@hotmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6177
Added missing ida_simple_remove() in the error handling path.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Closes#6159Closes#6172
In certain cases (dsl_scan_sync() is one), we may end up calling
bpobj_iterate() on an empty bpobj. Even though we don't end up
modifying the bpobj it still gets dirtied, causing unneeded writes
to the pool.
This patch adds an early bail from bpobj_iterate_impl() if bpobj
is empty to prevent unneeded writes.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6164
This reverts commit 959f56b993.
An issue was uncovered by the new zvol_misc_snapdev test case
which needs to be investigated and resolved.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6174
Issue #6131
When inheriting the "snapdev" property to we don't always call
zfs_prop_set_special(): this prevents device nodes from being created in
certain situations. Because "snapdev" is the only *special* property
that is also inheritable we need to call zfs_prop_set_special() even
when we're not reverting it to the received value ('zfs inherit -S').
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6131
Exclude Makefile.in in module/ and fix the gitignore in cmd/
Also, ignore *.patch and *.orig files
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Perform the already past expiration time check before updating
cvp->cv_mutex with the provided mutex. This check only depends
on local state. Doing it first ensures that cvp->cv_mutex will not
be updated in the timeout case or if it's ever called with an
expire_time <= now.
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#616
Provide a format parameter to super_setup_bdi_name() so we don't
create duplicate names in '/devices/virtual/bdi' sysfs namespace which
would prevent us from mounting more than one ZFS filesystem at a time.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6147
Sync with kernel patches for lz4
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/log/lib/lz4
4a3a99 lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
d5e7ca LZ4 : fix the data abort issue
bea2b5 lib/lz4: Pull out constant tables
99b7e9 lz4: fix system halt at boot kernel on x86_64
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Feng Sun <loyou85@gmail.com>
Closes#5975Closes#5973
This addition will enable us to sync an open TXG to the main pool
on demand. The functionality is similar to 'sync(2)' but 'zpool sync'
will return when data has hit the main storage instead of potentially
just the ZIL as is the case with the 'sync(2)' cmd.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#6122
This patch adds a '-f' option to 'zpool offline' to fault a vdev
instead of bringing it offline. Unlike the OFFLINE state, the
FAULTED state will trigger the FMA code, allowing for things like
autoreplace and triggering the slot fault LED. The -f faults
persist across imports, unless they were set with the temporary
(-t) flag. Both persistent and temporary faults can be cleared
with zpool clear.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6094
One pre-check in zfs_ereport_start() was being called after
the nvlists were being allocated. This simply corrects that
issue.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6140
The lock is designed to protect internal state of zvol_state_t and
to avoid taking spa_namespace_lock (e.g. in dmu_objset_own() code path)
while holding zvol_stat_lock. Refactor the code accordingly.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3484Closes#6065Closes#6134
Fix lock order inversion with zvol_open() as it did not account
for use of zvols as vdevs. The latter use cases resulted in the
lock order inversion deadlocks that involved spa_namespace_lock
and bdev->bd_mutex.
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6065
Issue #6134
On a raidz vdev, a block that does not span all child vdevs, excluding
its skip sectors if any, may not be affected by a child vdev outage or
failure. In such cases, the block does not need to be resilvered.
However, current resilver algorithm simply resilvers all blocks on a
degraded raidz vdev. Such spurious IO is not only wasteful, but also
adds the risk of overwriting good data.
This patch eliminates such spurious IOs.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5316
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
A standard practice in ZFS is to keep track of "per-txg" state. Any of
the 3 active TXG's (open, quiescing, syncing) can have different values
for this state. We should assert that we do not attempt to modify other
(inactive) TXG's.
Porting Notes:
- ASSERTV added to txg_sync_waiting() for unused variable.
OpenZFS-issue: https://www.illumos.org/issues/8063
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/01acb46Closes#6109
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
If we do a scrub while a leaf device is offline (via "zpool offline"),
we will inadvertently clear the DTL (dirty time log) of the offline
device, even though it is still damaged. When the device comes back
online, we will incompletely resilver it, thinking that the scrub
repaired blocks written before the scrub was started. The incomplete
resilver can lead to data loss if there is a subsequent failure of a
different leaf device.
The fix is to never clear the DTL of offline devices. Note that if a
device is onlined while a scrub is in progress, the scrub will be
restarted.
The problem can be worked around by running "zpool scrub" after
"zpool online".
OpenZFS-issue: https://www.illumos.org/issues/8166
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/372Closes#5806Closes#6103
The arc layer tracks checksums of its data in the arc header
so that it can ensure that buffers haven't changed when they're
not supposed to. This checksum is only maintained while there
is an uncompressed buffer still attached to the header.
Unfortunately there is a missing call to arc_free_cksum() in
arc_release() that can trigger ASSERTs. This has not been a
common issue because the checksums are only maintained for
debug builds and triggering the bug requires writing a block
(and therefore calling arc_release()) while a compressed buffer
is still being used on a debug build. This simply corrects the
issue.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6105
Linux 4.9 added current_time() as the preferred interface to get
the filesystem time. CURRENT_TIME was retired in Linux 4.12.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6114
This allows users to specify "-o property=value" to override and
"-x property" to exclude properties when receiving a zfs send stream.
Both native and user properties can be specified.
This is useful when using zfs send/receive for periodic
backup/replication because it lets users change properties such as
canmount, mountpoint, or compression without modifying the source.
References:
https://www.illumos.org/issues/2745https://www.illumos.org/issues/3753
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1350Closes#5349
Document the existence of `createtxg` and `guid` native properties
in man pages and zfs command output.
One of the great features of ZFS is incremental replication of
snapshots, possibly between pools on different machines.
Shell scripts are commonly used to auomate this procedure. They have to
find the most recent common snapshot between both sides and then
perform incremental send & recv.
Currently, scripts rely on the sorting order of `zfs list`, which
defaults to `createtxg`, and the assumption that snapshot names on
either side do not change.
By making `createtxg` and `guid` part of the public ZFS interface,
scripts are enabled to use
a) `createtxg` to determine the logical & temporal order of snapshots
(the creation property is not an equivalent substitute since
multiple snapshots may be created within one second)
b) `guid` to uniquely identify a snapshot, independent of its current
display name
This has the potential of making scripts safer and correct.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#6102
zfsonlinux/spl@8f87971 added __spl_pf_fstrans_check for the xfs related
check, so we use them accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#6113
Change SPL_FSTRANS to optionally contains PF_FSTRANS. Also, add
__spl_pf_fstrans_check for the checks specifically for PF_FSTRANS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#614
Remove the lz4_ac local variable from dmu_write_policy() to resolve
the following unused variable warning on non-debug builds.
dmu.c: In function ‘dmu_write_policy’:
dmu.c:1892:12: warning: unused variable ‘lz4_ac’ [-Wunused-variable]
boolean_t lz4_ac = spa_feature_is_active(os->os_spa,
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The proposed debugging enhancements in zfsonlinux/spl#587
identified the following missing *_destroy/*_fini calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5428
Change the default ZVOL behavior so requests are handled asynchronously.
This behavior is functionally the same as in the zfs-0.6.4 release.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5902
Linux has read-ahead logic designed to accelerate sequential workloads.
ZFS has its own read-ahead logic called zprefetch that operates on both
ZVOLs and datasets. Having two prefetchers active at the same time can
cause overprefetching, which unnecessarily reduces IOPS performance on
CoW filesystems like ZFS.
Testing shows that entirely disabling the Linux prefetch results in
a significant performance penalty for reads while commensurate benefits
are seen in random writes. It appears that read-ahead benefits are
inversely proportional to random write benefits, and so a single page
of Linux-layer read-ahead appears to offer the middle ground for both
workloads.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Issue #5902
The current ZVOL implementation does not explicitly set merge
options on ZVOL device queues, which results in the default merge
behavior.
Explicitly set QUEUE_FLAG_NOMERGES on ZVOL queues allowing the
ZIO pipeline to do its work.
Initial benchmarks (tiotest with no O_DIRECT) show random write
performance going up almost 3X on 8K ZVOLs, even after significant
rewrites of the logical space allocation.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: RageLtMan <rageltman@sempervictus>
Issue #5902
This commit allow higher ashift values (up to 16) in 'zpool create'
The ashift value was previously limited to 13 (8K block) in b41c990
because the limited number of uberblocks we could fit in the
statically sized (128K) vdev label ring buffer could prevent the
ability the safely roll back a pool to recover it.
Since b02fe35 the largest uberblock size we support is 8K: this
allow us to store a minimum number of 16 uberblocks in the vdev
label, even with higher ashift values.
Additionally change 'ashift' pool property behaviour: if set it will
be used as the default hint value in subsequent vdev operations
('zpool add', 'attach' and 'replace'). A custom ashift value can still
be specified from the command line, if desired.
Finally, fix a bug in add-o_ashift.ksh caused by a missing variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2024Closes#4205Closes#4740Closes#5763
When vdev_psize increases, the location of labels 2 and 3 changes
because their location is relative to the end of the device.
The configs for labels 2 and 3 are written during the next spa_sync()
because the vdev is added to the dirty config list. However, the
uberblock rings are not re-written in their new location, leaving the
device vulnerable to the beginning of the device being overwritten or
damaged.
This patch copies the uberblock ring from label 0 to labels 2 and 3,
in their new locations, at the next sync after vdev_psize increases.
Also, add a test zpool_expand_004_pos.ksh to confirm the uberblocks
are copied.
Reviewed-by: BearBabyLiu <liu.huang@zte.com.cn>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5108
When multiple filesystems are in use, memory pressure causes arc_cache
to collapse to a minimum. Allow arc_cache to maintain proportional size
even when hit rates are disproportionate. We do this only via evictable
size from the kernel shrinker, thus it's only in effect under memory
pressure.
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6035
Could return the wrong pages value
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Calling it when nothing is evictable will cause extra kswapd cpu. Also
if we didn't shrink it's unlikely to have memory to reap because we
likely just called it microseconds ago. The exception is if we are in
direct reclaim.
You can see how hard this is being hit in kswapd with a light test
workload:
34.95% [zfs] [k] arc_kmem_reap_now
5.40% [spl] [k] spl_kmem_cache_reap_now
3.79% [kernel] [k] _raw_spin_lock
2.86% [spl] [k] __spl_kmem_cache_generic_shrinker.isra.7
2.70% [kernel] [k] shrink_slab.part.37
1.93% [kernel] [k] isolate_lru_pages.isra.43
1.55% [kernel] [k] __wake_up_bit
1.20% [kernel] [k] super_cache_count
1.20% [kernel] [k] __radix_tree_lookup
With ZFS just mounted but only ext4/pagecache memory pressure
arc_kmem_reap_now still consumes excessive CPU:
12.69% [kernel] [k] isolate_lru_pages.isra.43
10.76% [kernel] [k] free_pcppages_bulk
7.98% [kernel] [k] drop_buffers
7.31% [kernel] [k] shrink_page_list
6.44% [zfs] [k] arc_kmem_reap_now
4.19% [kernel] [k] free_hot_cold_page
4.00% [kernel] [k] __slab_free
3.95% [kernel] [k] __isolate_lru_page
3.09% [kernel] [k] __radix_tree_lookup
Same pagecache only workload as above with this patch series:
11.58% [kernel] [k] isolate_lru_pages.isra.43
11.20% [kernel] [k] drop_buffers
9.67% [kernel] [k] free_pcppages_bulk
8.44% [kernel] [k] shrink_page_list
4.86% [kernel] [k] __isolate_lru_page
4.43% [kernel] [k] free_hot_cold_page
4.00% [kernel] [k] __slab_free
3.44% [kernel] [k] __radix_tree_lookup
(arc_kmem_reap_now has 0 samples in perf)
AKAMAI: zfs: CR 3695042
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Lock contention, by itself, shouldn't indicate a stop condition to the
kernel's slab shrinker. Doing so can cause stalls when the kernel is
trying to free large parts of the cache such as is done by drop_caches
Also, perhaps arc_reclaim_lock should be a spinlock, and this code
eliminated.
AKAMAI: zfs: CR 3593801
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Move arcstat_need_free increment from all direct calls to when
arc_reclaim_lock is busy and we exit wihout doing anything. Data will
be reclaimed in reclaim thread. The previous location meant that we
both reclaim the memory in this thread, and also schedule the same
amount of memory for reclaim in arc_reclaim, effectively doubling the
requested reclaim.
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Ensures proper accounting of bytes we requested to free
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
Ghost meta/data buffers are not actually allocated
AKAMAI: zfs: CR 3695072
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Issue #6035
It doesn't need to have a loop to free page in a single scatterlist
entry because it should be single or compound page. The pages can be
freed in one invocation to __free_pages() for both cases.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Jinshan Xiong <jinshan.xiong@gmail.com>
Closes#6057
In current implementation, only zio buffers in 16KB and bigger are
guaranteed PAGESIZE alignment. This breaks Lustre since it assumes
that 'arc_buf_t::b_data' must be page aligned when zio buffers are
greater than or equal to PAGESIZE.
This patch will make the zio buffers to be PAGESIZE aligned when
the sizes are not less than PAGESIZE.
This change may cause a little bit memory waste but that should be
fine because after ABD is introduced, zio buffers are used to hold
data temporarily and live in memory for a short while.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jinshan Xiong <jinshan.xiong@gmail.com>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Closes#6084
All filesystems were converted to dynamically allocated BDIs. The
destruction of backing_dev_info structures is handled as part of
super block destruction. Refactor the code to abstract away the
details of creating and destroying a BDI.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6089
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: bunder2015 <omfgbunder@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/7786
OpenZFS-commit: http://github.com/openzfs/openzfs/commit/db8498fCloses#6074
Commit 37f9dac removed the zvol_taskq for processing zvol requests.
This was removed as part of switching to make_request_fn and was
motivated by a concern at the time over dispatch latency.
However, this also made all bio request synchronous, and caused
serious performance issues as the bio submitter would wait for
every bio it submitted, effectively making the IO depth 1.
This patch reinstate zvol_taskq, and to make sure overlapped I/Os
are ordered properly, we take range lock in zvol_request, and pass
it along with bio to the I/O functions zvol_{write,discard,read}.
In order to facilitate benchmarks a zvol_request_sync module
option was added to switch between sync and async request handling.
For the moment, the default behavior is synchronous but this is
likely to change pending additional testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5824
OpenZFS 7252 - compressed zfs send / receive
OpenZFS 7628 - create long versions of ZFS send / receive options
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: David Quigley <dpquigl@davequigley.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: bunder2015 <omfgbunder@gmail.com>
Ported-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Most of 7252 was already picked up during ABD work. This
commit represents the gap from the final commit to openzfs.
- Fixed split_large_blocks check in do_dump()
- An alternate version of the write_compressible() function was
implemented for Linux which does not depend on fio. The behavior
of fio differs significantly based on the exact version.
- mkholes was replaced with truncate for Linux.
OpenZFS-issue: https://www.illumos.org/issues/7252
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/5602294Closes#6067
After run a long time with QAT compression, the variable "inst_num"
is overflow by "atomic_inc_32_nv", which causes its neighbor
variable overwritten. Change its definition from U16 to U32.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#6051
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
dbuf_read() creates a zio_root() to track and wait for all the zio's
that may happen as part of this call. However, if the blkptr_t for
this buffer is NULL or a hole, we will not create any more zio's, so
this zio_root() is unnecessary. This is always the case when calling
dbuf_read() on a bonus buffer, because it has no blkptr (it's part of
the containing dnode). For workloads that read a lot of bonus buffers
(e.g. file creation and removal), creating and destroying these
unnecessary zio's can decrease performance by around 3%.
The fix is to only create/destroy the zio_root() in dbuf_read() if the
blkptr is not NULL and not a hole.
Porting Notes:
- The error handling for when dbuf_read_impl() fails which was
originally added in commit 5f6d0b6f5 has been preserved.
OpenZFS-issue: https://www.illumos.org/issues/8025
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8ec5c7cCloses#6048
Fixup commit 66aca24. We should have equivalent return
values as generic_file_llseek() and advance to end of file.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tested-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#6050Closes#6053
The existing assertions in vdev_label_read() and vdev_label_write(),
testing which config locks are held, are incorrect. The assertions
test for locks which exceed what is required for safety.
Both vdev_label_{read,write}() are changed to assert SCL_STATE is held
as RW_READER or RW_WRITER. This is safe because:
Changes to the vdev tree occur under SCL_ALL as RW_WRITER, via
spa_vdev_enter() and spa_vdev_exit().
Changes to vdev state occur under SCL_STATE_ALL as RW_WRITER, via
spa_vdev_state_enter() and spa_vdev_state_exit().
Therefore, the new assertions guarantee that the vdev cannot change
out from under a zio, and I/O to a specified leaf vdev's label is
safe.
Furthermore, this is consistent with the SPA locking discussion in
spa_misc.c, "For any zio operation that takes an explicit vdev_t
argument ... zio_read_phys(), or zio_write_phys() ... SCL_STATE as
reader suffices."
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5983
Resilver operations frequently cause only a small amount of dirty data
to be written to disk at a time, resulting in the IO scheduler to only
issue 1 write at a time to the resilvering disk. When it is rotational
media the drive will often travel past the next sector to be written
before receiving a write command from ZFS, significantly delaying the
write of the next sector.
Raise zfs_vdev_async_write_min_active so that drives are kept fed
during resilvering.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Issue #4825Closes#5926
Authored by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
sa_find_idx_tab() is declared as taking and returning "void *" parameters.
These can be declared to be the specific types.
OpenZFS-issue: https://www.illumos.org/issues/8061
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4e64affCloses#6017
Authored by: Andriy Gapon <avg@FreeBSD.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
When querying ZPL properties verify that the objset is of type
DMU_OST_ZFS.
OpenZFS-issue: https://www.illumos.org/issues/6101
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ce2243aCloses#6015
Force flushing of txg's can be painfully slow when competing for disk
IO, since this is a process meant to execute asynchronously. Optimize
this path via allowing data/hole seeking if the file is clean, but if
dirty fall back to old logic. This is a compromise to disabling the
feature entirely.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Closes#4306Closes#5962
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- grub-2.02-beta2-422-gcad5cc0 includes support for large blocks.
- Commit 8aab121 allowed GZIP[1-9].
- Grub allows pools with multiple top-level vdevs.
OpenZFS-issue: https://www.illumos.org/issues/5120
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c8811bdCloses#6007
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Enable internal log for DEBUG builds and in zfs-tests.sh.
- callbacks/zfs_dbgmsg.ksh - Dump interal log via kstat.
- callbacks/zfs_dmesg.ksh - Dump dmesg log.
- default.cfg - 'Test Suite Specific Commands' dropped.
OpenZFS-issue: https://www.illumos.org/issues/7503
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/55a1300Closes#6002
In zfs_ereport_post, if an event is a rate limiting
event, immediately return before any processing is done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5998
When we try assign a new transaction to a TXG we must know beforehand
if there is sufficient free space on disk. This is to decide,
in dmu_tx_assign(), if we should reject the TX with ENOSPC.
We rely on spa_get_worst_case_asize() to inflate the size of our
logical writes by a factor of spa_asize_inflation which is
calculated as:
(VDEV_RAIDZ_MAXPARITY + 1) * SPA_DVAS_PER_BP * 2 == 24
The problem with the current implementation is that we don't take
into account what happens with very small writes on VDEVs with large
physical block sizes.
Consider the case of writes to a dataset with recordsize=512,
copies=3 on a VDEV with ashift=13 (usually SSD with 8K block size):
every logical IO will end up allocating 3 * 8K = 24K on disk, so 512
bytes multiplied by 48, which is double the size we account for.
If we allow this kind of writes to be assigned a TX it is possible,
when the pool is almost full, to trigger an allocation failure
(ENOSPC) in the ZIO pipeline, which will in turn result in the whole
pool being suspended.
The bug is fixed by using, in spa_get_worst_case_asize(), the MAX()
value chosen between the logical io size from zfs_write() and the
maximum physical block size used among our VDEVs.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5941
Authored by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Ported-by: Matt Ahrens <mahrens@delphix.com>
RAID-Z requires that space be allocated in multiples of P+1 sectors,
because this is the minimum size block that can have the required amount
of parity. Thus blocks on RAIDZ1 must be allocated in a multiple of 2
sectors; on RAIDZ2 multiple of 3; and on RAIDZ3 multiple of 4. A sector
is a unit of 2^ashift bytes, typically 512B or 4KB.
To satisfy this constraint, the allocation size is rounded up to the
proper multiple, resulting in up to 3 "pad sectors" at the end of some
blocks. The contents of these pad sectors are not used, so we do not
need to read or write these sectors. However, some storage hardware
performs much worse (around 1/2 as fast) on mostly-contiguous writes
when there are small gaps of non-overwritten data between the writes.
Therefore, ZFS creates "optional" zio's when writing RAID-Z blocks that
include pad sectors. If writing a pad sector will fill the gap between
two (required) writes, we will issue the optional zio, thus doubling
performance. The gap-filling performance improvement was introduced in
July 2009.
Writing the optional zio is done by the io aggregation code in
vdev_queue.c. The problem is that it is also subject to the limit on
the size of aggregate writes, zfs_vdev_aggregation_limit, which is by
default 128KB. For a given block, if the amount of data plus padding
written to a leaf device exceeds zfs_vdev_aggregation_limit, the
optional zio will not be written, resulting in a ~2x performance
degradation.
The problem occurs only for certain values of ashift, compressed block
size, and RAID-Z configuration (number of parity and data disks). It
cannot occur with the default recordsize=128KB. If compression is
enabled, all configurations with recordsize=1MB or larger will be
impacted to some degree.
The problem notably occurs with recordsize=1MB, compression=off, with 10
disks in a RAIDZ2 or RAIDZ3 group (with 512B or 4KB sectors). Therefore
this problem has been known as "the 1MB 10-wide RAIDZ2 (or 3) problem".
The problem also occurs with the following configurations:
With recordsize=512KB or 256KB, compression=off, the problem occurs only
in rarely-used configurations:
* 4-wide RAIDZ1 with recordsize=512KB and ashift=12 (4KB sectors)
* 4-wide RAIDZ2 (either recordsize, either ashift)
* 5-wide RAIDZ2 with recordsize=512KB (either ashift)
* 6-wide RAIDZ2 with recordsize=512KB (either ashift)
With recordsize=1MB, compression=off, ashift=9 (512B sectors)
* RAIDZ1 with 4 or 8 disks
* RAIDZ2 with 4, 8, or 10 disks
* RAIDZ3 with 6, 8, 9, or 10 disks
With recordsize=1MB, compression=off, ashift=12 (4KB sectors)
* RAIDZ1 with 7 or 8 disks
* RAIDZ2 with 4, 5, or 10 disks
* RAIDZ3 with 6, 9, or 10 disks
With recordsize=2MB and larger (which can only be selected by changing
kernel tunables), many configurations are affected, including with
higher numbers of disks (up to 18 disks with recordsize=2MB).
Increase zfs_vdev_aggregation_limit to allow the optional zio to be
aggregated, thus eliminating the problem. Setting it to 256KB fixes all
commonly-used configurations.
The solution is to aggregate optional zio's regardless of the
aggregation size limit.
Analysis sponsored by Intel Corp.
OpenZFS-issue: https://www.illumos.org/issues/8005
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/321Closes#5931
Authored by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@nexenta.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/2932
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/810e43bCloses#5984Closes#5216
Authored by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
We don't want to dirty any data when we're in the final txgs of the pool
export logic. This change introduces checks to make sure that no data is
dirtied after a certain point. It also addresses the culprit of this
specific bug – the space map cannot be upgraded when we're in final
stages of pool export. If we encounter a space map that wants to be
upgraded in this phase, then we simply ignore the request as it will get
retried the next time we set the fragmentation metric on that metaslab.
OpenZFS-issue: https://www.illumos.org/issues/8023
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2ef00f5Closes#5991
On 32-bit platforms spa_state is 32 bits without cast, and thus
caused a NULL pointer dereference when treated as 64bit in
var arg. Accidentally introduced by bcdb96a.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5966Closes#5965
Authored by: Steven Hartland <steven.hartland@multiplay.co.uk>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
When a member of a RAIDZ has been replaced with a device smaller than
the original, then the top level vdev can report its expand size as
16.0E.
The reduced child asize causes the RAIDZ to have a vdev_asize lower than
its vdev_max_asize which then results in an underflow during the
calculation of the parents expand size.
Fix this by updating the vdev_asize if it shrinks, which is already
protected by a check against vdev_min_asize so should always be safe.
Also for RAIDZ vdevs, ensure that the sum of their child vdev_min_asize
is always greater than the parents vdev_min_size.
Reviewed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7885
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bb0dbaaCloses#5963
* Add ZPOOL pool state to zfs_post_common to
allow differentiation between export and destroy
by zedlets.
* Add pool name as standard export This ensures
pool name is exported to zedlets.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Closes#5942
Wherever possible it's best to avoid depending on a linear ABD.
Update the code accordingly in the following areas.
- vdev_raidz
- zio, zio_checksum
- zfs_fm
- change abd_alloc_for_io() to use abd_alloc()
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5668
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
The offset arguments is wrong when changing to abd_copy_off in a6255b7
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5932Closes#5936
For historical reasons zfs_mknode() was written such that it could
never fail. This poses a problem for Linux since zfs_znode_alloc()
could potentually failure due to low memory. Handle this gracefully
by retrying zfs_znode_alloc() until it succeeds, direct reclaim
will eventually be able to allocate memory.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5535Closes#5908
This patch implement the hardware accelerator method in GZIP compression
in ZFS. When the ZFS pool is enabled GZIP compression, the compression
API will be automatically transferred to the hardware accelerator to
free up CPU resource and speed up the compression time.
* To enable Intel QAT hardware acceleration in ZOL you need to have QAT
hardware and the driver installed:
* QAT hardware DH8950:
http://ark.intel.com/products/79483/Intel-QuickAssist-Adapter-8950
* QAT driver:
https://01.org/intel-quickassist-technology
* Start QAT driver in your system:
service qat_service start
* Enable QAT in ZFS, e.g.:
./configure --with-qat=<qat-driver-path>/QAT1.6
make
* Set GZIP compression in ZFS dataset:
zfs set compression = gzip <dataset>
* Get QAT hardware statistics by:
cat /proc/spl/kstat/zfs/qat
* To disable QAT in ZFS:
insmod zfs.ko zfs_qat_disable=1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Weigang Li <weigang.li@intel.com>
Closes#5846
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Matthew Ahrens <mahrens@delphix.com>
spa_sync() iterates over all the dirty dnodes and processes each of them
by calling dnode_sync(). If there are many dirty dnodes (e.g. because we
created or removed a lot of files), the single thread of spa_sync()
calling dnode_sync() can become a bottleneck. Additionally, if many
dnodes are dirtied concurrently in open context (e.g. due to concurrent
file creation), the os_lock will experience lock contention via
dnode_setdirty().
The solution is to track dirty dnodes on a multilist_t, and for
spa_sync() to use separate threads to process each of the sublists in
the multilist.
OpenZFS-issue: https://www.illumos.org/issues/7968
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4a2a54cCloses#5752
In torvalds/linux@a528d35, there are changes to the getattr family of functions,
struct kstat, and the interface of inode_operations .getattr.
The inode_operations .getattr and simple_getattr() interface changed to:
int (*getattr) (const struct path *, struct dentry *, struct kstat *,
u32 request_mask, unsigned int query_flags)
The request_mask argument indicates which field(s) the caller intends to use.
Fields the caller has not specified via request_mask may be set in the returned
struct anyway, but their values may be approximate.
The query_flags argument indicates whether the filesystem must update
the attributes from the backing store.
Currently both fields are ignored. It is possible that getattr-related
functions within zfs could be optimized based on the request_mask.
struct kstat includes new fields:
u32 result_mask; /* What fields the user got */
u64 attributes; /* See STATX_ATTR_* flags */
struct timespec btime; /* File creation time */
Fields attribute and btime are cleared; the result_mask reflects this. These
appear to be optional based on simple_getattr() and vfs_getattr() within the
kernel, which take the same approach.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5875
Before kernel 2.6.29 credentials were embedded in task_structs, and zfs had
cases where one thread would need to refer to the credential of another thread,
forcing it to take a hold on the foreign thread's task_struct to ensure it was
not freed.
Since 2.6.29, the credential has been moved out of the task_struct into a
cred_t.
In addition, the mainline kernel originally did not export __put_task_struct()
but the RHEL5 kernel did, according to zfsonlinux/spl@e811949a57. As of
2.6.39 the mainline kernel exports it.
There is no longer zfs code that takes or releases holds on a task_struct, and
so there is no longer any reference to __put_task_struct().
This affects the linux 4.11 kernel because the prototype for
__put_task_struct() is in a new include file (linux/sched/task.h) and so the
config check failed to detect the exported symbol.
Removing the unnecessary stub and corresponding config check. This works on
kernels since the oldest one currently supported, 2.6.32 as shipped with
Centos/RHEL.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#608
There are changes to vfs_getattr() in torvalds/linux@a528d35. The new
interface is:
int vfs_getattr(const struct path *path, struct kstat *stat,
u32 request_mask, unsigned int query_flags)
The request_mask argument indicates which field(s) the caller intends to
use. Fields the caller does not specify via request_mask may be set in
the returned struct anyway, but their values may be approximate.
The query_flags argument indicates whether the filesystem must update
the attributes from the backing store.
This patch uses the query_flags which result in vfs_getattr behaving the same
as it did with the 2-argument version which the kernel provided before
Linux 4.11.
Members blksize and blocks are now always the same size regardless of
arch. They match the size of the equivalent members in vnode_t.
The configure checks are modified to ensure that the appropriate
vfs_getattr() interface is used.
A more complete fix, removing the ZFS dependency on vfs_getattr()
entirely, is deferred as it is a much larger project.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#608
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
When we do a clone swap (caused by "zfs rollback" or "zfs receive"), the
ZPL doesn't completely reload the state from the DMU; some values remain
cached in the zfsvfs_t.
OpenZFS-issue: https://www.illumos.org/issues/6874
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1fdcbd0Closes#5888
Restructure the handling of mount options to be consistent with
upstream OpenZFS. This required making the following changes.
- The zfs_mntopts_t was renamed vfs_t and adjusted to provide
the minimal needed functionality. This includes a pointer
back to the associated zfsvfs_t. Plus it made it possible
to revert zfs_register_callbacks() and zfsvfs_create() back
to their original prototypes.
- A zfs_mnt_t structure was added for the sole purpose of
providing a structure to pass the osname and raw mount
pointer to zfs_domount() without having to copy them.
- Mount option parsing was moved down from the zpl_* wrapper
functions in to the zfs_* functions. This allowed for the
code to be simplied and it's where similar functionality
appears on other platforms.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Several functions were renamed when ZFS was originally ported to
Linux. Revert the code to the original names to minimize the
delta with upstream OpenZFS.
zfs_sb_teardown -> zfsvfs_teardown
zfs_sb_create -> zfsvfs_create
zfs_sb_setup -> zfsvfs_setup
zfs_sb_free -> zfsvfs_free
get_zfs_sb -> getzfsvfs
zfs_sb_hold -> zfsvfs_hold
zfs_sb_rele -> zfsvfs_rele
zfs_sb_prune_aliases -> zfs_prune_aliases (Linux-only)
zfs_sb_prune -> zfs_prune (Linux only)
Align the zfs_vnops.h and zfs_vfsops.h with upstream as much
as possible. Several prototypes were removed and those that
remain were reordered.
Move the EXPORT_SYMBOL lines to the end of the source files
for consistency with the other source files.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The use of zfs_sb_t instead of zfsvfs_t results in unnecessary
conflicts with the upstream source. Change all instances of
zfs_sb_t to zfsvfs_t including updating the variables names.
Whenever possible the code was updated to be consistent with
hope it appears in the upstream OpenZFS source.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The BLKFLSBUF ioctl is expected to do two things:
- flush dirty pages to stable storage, and
- invalidate clean pages
Unfortunately, the existing implementation of BLKFLSBUF in
zvol_ioctl() only flushes pages which are part of the current
TXG to disk. There may be additional dirty pages in the
page cache which haven't yet been submitted to the DMU and
therefore aren't part of any TXG.
Furthermore because zvol_ioctl() returns 0 the generic
blkdev_flushbuf() does not invalidate the page cache.
Resolve the issue by moving bdev_flush() in to zvol_ioctl()
and explicitly waiting for a full TXG sync. Then invalidate
the page cache. The associated ARC buffers need not be
evicted since they cannot be bypassed using O_DIRECT.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5871Closes#5879
Newer versions of cppcheck find the potential NULL pointer
bug in zfs_write(). The function is difficult to refactor without
extensive work, so suppress the potential NULL pointer error
which cannot occur for now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5882
The current implementation for allowing nfs to access snapdir is very buggy.
It uses a special fh for snapdirs, such that the next time nfsd does
fh_to_dentry, it actually returns the root inode inside the snapshot. So nfsd
never knows it cross a mountpoint.
The problem is that nfsd will not hold a reference on the vfsmount of the
snapshot. This cause auto unmounter to unmount the snapshot even though nfs is
still holding dentries in it.
To fix this, we return the inode for the snapdirs themselves. However, we also
trigger automount upon fh_to_dentry, and return ESTALE so nfsd will revalidate
and see the mountpoint and do crossmnt.
Because nfsd will now be aware that these are different filesystems users
must add crossmnt to their export options to access snapshot directories.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#3794Closes#4716Closes#5810Closes#5833
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Tim Chase <tim@chase2k.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7867
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/aa1f740dCloses#5874
Properly annotate functions and data section so that objtool does not complain
when CONFIG_STACK_VALIDATION and CONFIG_FRAME_POINTER are enabled.
Pass KERNELCPPFLAGS to assembler.
Use kfpu_begin()/kfpu_end() to protect SIMD regions in Linux kernel.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5872Closes#5041
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Background information: This assertion about tx_space_* verifies that we
are not dirtying more stuff than we thought we would. We “need” to know
how much we will dirty so that we can check if we should fail this
transaction with ENOSPC/EDQUOT, in dmu_tx_assign(). While the
transaction is open (i.e. between dmu_tx_assign() and dmu_tx_commit() —
typically less than a millisecond), we call dbuf_dirty() on the exact
blocks that will be modified. Once this happens, the temporary
accounting in tx_space_* is unnecessary, because we know exactly what
blocks are newly dirtied; we call dnode_willuse_space() to track this
more exact accounting.
The fundamental problem causing this bug is that dmu_tx_hold_*() relies
on the current state in the DMU (e.g. dn_nlevels) to predict how much
will be dirtied by this transaction, but this state can change before we
actually perform the transaction (i.e. call dbuf_dirty()).
This bug will be fixed by removing the assertion that the tx_space_*
accounting is perfectly accurate (i.e. we never dirty more than was
predicted by dmu_tx_hold_*()). By removing the requirement that this
accounting be perfectly accurate, we can also vastly simplify it, e.g.
removing most of the logic in dmu_tx_count_*().
The new tx space accounting will be very approximate, and may be more or
less than what is actually dirtied. It will still be used to determine
if this transaction will put us over quota. Transactions that are marked
by dmu_tx_mark_netfree() will be excepted from this check. We won’t make
an attempt to determine how much space will be freed by the transaction
— this was rarely accurate enough to determine if a transaction should
be permitted when we are over quota, which is why dmu_tx_mark_netfree()
was introduced in 2014.
We also won’t attempt to give “credit” when overwriting existing blocks,
if those blocks may be freed. This allows us to remove the
do_free_accounting logic in dbuf_dirty(), and associated routines. This
logic attempted to predict what will be on disk when this txg syncs, to
know if the overwritten block will be freed (i.e. exists, and has no
snapshots).
OpenZFS-issue: https://www.illumos.org/issues/7793
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3704e0a
Upstream bugs: DLPX-32883a
Closes#5804
Porting notes:
- DNODE_SIZE replaced with DNODE_MIN_SIZE in dmu_tx_count_dnode(),
Using the default dnode size would be slightly better.
- DEBUG_DMU_TX wrappers and configure option removed.
- Resolved _by_dnode() conflicts these changes have not yet been
applied to OpenZFS.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7843
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4d519e7Closes#5868
Commit 933ec99 removes read and write from f_op because the vfs layer will
select iter_write or aio_write automatically. However, for Linux <= 4.0,
loop_set_fd will actually check f_op->write and set read-only if not exists.
This patch add them back and use the generic do_sync_{read,write} for
aio_{read,write} and new_sync_{read,write} for {read,write}_iter.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5776Closes#5855
Linux 4.11 introduces a new type, refcount_t, which conflicts with the
type of the same name defined within ZFS.
Rename the ZFS type zfs_refcount_t. Within the ZFS code, use a macro to
cause references to refcount_t to be changed to zfs_refcount_t at
compile time. This reduces conflicts when later landing OpenZFS
patches.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5823Closes#5842
0eef1bde31
introduced some changes which we slightly improved the style of when
porting to illumos.
There is also one minor error-handling fix, in zap_add() the "zap" may
become NULL in case of an error re-opening the ZAP.
Originally suggested at: https://github.com/openzfs/openzfs/pull/276
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5805
The commit a6255b7fce removed a few
assertions which help catch errors and improve code readability. It also
duplicated two conditionals, which was unnecessary and made the code
confusing to read. This patch cleans it up.
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5802
Authored by: Daniel Hoffman <dj.hoffman@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
This change removes all gendered language that did not refer specifically
to an individual person or pet. The convention taken was to use
variations on "they" when referring to users and/or human beings, while
using "it" when referring to code, functions, and/or libraries.
Additionally, we took the liberty to fix up any whitespace issues that
were found in any files that were already being modified.
OpenZFS-issue: https://www.illumos.org/issues/7812
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ad626dbCloses#5822
7200 no blocks must be born in a txg after a snaphot is created
Authored by: Andriy Gapon <andriy.gapon@clusterhq.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7199
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/bfaed0bCloses#5817
After a hot spare replaces an OFFLINE vdev, the new
parent spare vdev state is set incorrectly to OFFLINE.
The correct state should be DEGRADED. The incorrect
OFFLINE state will prevent top-level vdev from reading
the spare vdev, thus causing unnecessary reconstruction.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Isaac Huang <he.huang@intel.com>
Closes#5766Closes#5770
Replace uses of set_task_state(current, STATE) with
set_current_state(STATE).
In Linux 4.11, torvalds/linux@642fa44, set_task_state() is removed.
All spl uses are of the form set_task_state(current, STATE).
set_current_state(STATE) is equivalent and has been available since
Linux 2.2.26.
Furthermore, set_current_state(STATE) is already used in about 15
locations within spl. This change should have no impact other than
removing an unnecessary dependency.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#603
The global tunable zfs_arc_num_sublists_per_state is used by the ARC and
the dbuf cache, and other users are planned. We should change this
tunable to be common to all multilists. This tuning may be overridden
on a per-multilist basis.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5764
A likely cut/paste error caused the description to be applied to
zfs_arc_average_blocksize.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5788
Doing the following command would return success with zfs creating an orphan
object.
touch $(for i in $(seq 256); do printf "n"; done)
The funny thing is that this will only work once for each directory, because
after upgraded to fzap, zfs_lookup would fail properly since it has additional
length check.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5768
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7104
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4b5c8e9Closes#5679
This is a race condition in the deadlist code.
A thread executing an administrative command that uses
dsl_deadlist_space_range() holds the lock of the whole deadlist_t to
protect the access of all its entries that the deadlist contains in an
avl tree.
Sync threads trying to insert a new entry in the deadlist (through
dsl_deadlist_insert() -> dle_enqueue()) do not hold the deadlist lock at
that moment. If the dle_bpobj is the empty bpobj (our sentinel value),
we close and reopen it. Between these two operations, it is possible
for the dsl_deadlist_space_range() thread to dereference that bpobj
which is NULL during that window.
Threads should hold the a deadlist's dl_lock when they manipulate its
internal data so scenarios like the one above are avoided.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5762
As explicitly stated in section 2 of the 'Programming rules'
comments at the top of zfs_vnops.c.
If you must call iput() within a tx then use zfs_iput_async().
Move iput() calls after dmu_tx_commit() / dmu_tx_abort when
possible. When not possible convert the iput() calls to
zfs_iput_async().
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5758
Add the appropriate compiler flags to accept c99 code. This will help to
minimize differences with upstream, and aid porting changes. One change was
necessary in zvol.c because the DEFINE_IDA() macro does not work with the new
compiler flags.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#5756
When the code was added this tunable was not exposed via module params. Also it
was not documented. This patch changes the type from a uint32 to a ulong as
done with other percentage tunables and also documents it in the
zfs-module-parameters man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#5750
Authored by: Hans Rosenfeld <hans.rosenfeld@nexenta.com>
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Alek Pinchuk <alek.pinchuk@nexenta.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7448
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/295438bCloses#5737
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7247
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/2ad25b4Closes#5689
Porting notes:
- tests/zfs-tests/tests/functional/cli_root/zfs_receive/zfs_receive_013_pos.ksh
renamed as zfs_receive_015_pos.ksh, zfs_receive_013_pos.ksh is now
used for OpenZFS test.
- libzfs_sendrecv.c: SMALLEST_POSSIBLE_MAX_DDT_MB is always used
for all 32-bit builds.
For generic_write_checks with 2 args, we can exit when it returns zero because
it means count is zero. However this is not the case for generic_write_checks
with 4 args, where zero means no error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5720Closes#5726
This is effectively dead code for the Linux implementation which can
be removed to improve readability. We want to linter to check the
real production/debug build as much as possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5722
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7072
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c39a2aaCloses#5694
Porting notes:
- vdev.c: 'vdev_get_stats' changes are moved to 'vdev_get_stats_ex'.
- vdev_disk.c: ignored, Linux specific code is different.
This patch adds the necessary infrastructure for ABD to make use
of the vectorized fletcher 4 routines.
- export ABD compatible interface from fletcher_4
- add ABD fletcher_4 tests for data and metadata ABD types.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Original-patch-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#5589
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes: Moved reference_tracking_enable and
reference_history outside of ZFS_DEBUG.
OpenZFS-issue: https://www.illumos.org/issues/7545
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4dd77f9Closes#5701
The deadman in ZoL didn't behave quite as it did in upstream
OpenZFS. In addition to the 2 purposes for which OpenZFS used the
zfs_deadman_synctime_ms parameter, ZoL also used it to determine how
frequently the deadman would fire once it has been triggered.
This patch adds the zfs_deadman_checktime_ms parameter to control how
frequently the subsequent checks are performed.
The deadman is now disabled for suspended pools.
As had been the case, unlike upstream OpenZFS, ZoL will not panic when
a hung IO is detected.
The module parameter documentation has been upated to include the new
parameter and to better describe the operation of the deadmen.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5695
Resolve a false positive in the kmemleak checker by shifting to the
kernel slab. It shows up because vn_file_cache is using KMC_KMEM
which is directly allocated using __get_free_pages, which is not
automatically tracked by kmemleak.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#599
Authored by: Alex Wilson <alex.wilson@joyent.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7019
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45b1747Closes#5709
Authored by: Alan Somers <asomers@gmail.com>
7115 6922 generates ESC_ZFS_VDEV_REMOVE_AUX a bit too often
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7136
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b72b6bbCloses#5691
Porting notes:
- Functionally this patch behaves the same as the OpenZFS
version but it was adapted because because ZoL doesn't
have the same illumos sysevent_t infrastructure and functionality.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7490
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/6cedfc3Closes#5693
Authored by: Alan Somers <asomers@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6922
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/63364b0Closes#5690
Porting notes:
- 'zfs_dbgmsg_print()' reintroduced to userspace.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7277
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/29bdd2fCloses#5684
After resuming a pool the godfather zio could have both the
ZIO_REEXECUTE_NOW and ZIO_REEXECUTE_SUSPEND bits set. This
can occur if some child zios set ZIO_REEXECUTE_NOW while
other set ZIO_REEXECUTE_SUSPEND. The godfather zio can
inherit both flags in zio_notify_parent().
The child zios which assigned the ZIO_REEXECUTE_SUSPEND flag
will be removed from the godfather's child list and added to
the spa->spa_suspend_zio_root child list. While child zios
with the ZIO_REEXECUTE_NOW bit set remain being monitored
by the godfather zio.
When the godfather zio executes zio_done() the presence of
the ZIO_REEXECUTE_SUSPEND bit results in all io_reexecute
being cleared. These child zios will then not be re-executed
and instead will be destroyed and lost.
The most straight forward way to address this situation is
to only clear the ZIO_REEXECUTE_SUSPEND bit and leave the
ZIO_REEXECUTE_NOW bit set.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: yuxiang <guo.yong33@zte.com.cn>
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3105d95Closes#5678
The .write/.read file operations callbacks can be retired since
support for .read_iter/.write_iter and .aio_read/.aio_write has
been added. The vfs_write()/vfs_read() entry functions will
select the correct interface for the kernel. This is desirable
because all VFS write/read operations now rely on common code.
This change also add the generic write checks to make sure that
ulimits are enforced correctly on write.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5587Closes#5673
metaslab_t:ms_freetree[TXG_SIZE] is only used in syncing context. We
should replace it with two trees: the freeing tree (ranges that we are
freeing this syncing txg) and the freed tree (ranges which have been
freed this txg).
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7613
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a8698da2Closes#5598
Authored by: Stephen Blinick <stephen.blinick@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7500
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/653af1bCloses#5639
When importing a pool with a large number of filesystems within the same
parent filesystem, we see that dmu_objset_find_dp() takes a long time.
It is called from 3 places: spa_check_logs(), spa_ld_claim_log_blocks(),
and spa_load_verify().
There are several ways to improve performance here:
1. We don't really need to do spa_check_logs() or
spa_ld_claim_log_blocks() if the pool was closed cleanly.
2. spa_load_verify() uses dmu_objset_find_dp() to check that no
datasets have too long of names.
3. dmu_objset_find_dp() is slow because it's doing
zap_value_search() (which is O(N sibling datasets)) to determine
the name of each dsl_dir when it's opened. In this case we
actually know the name when we are opening it, so we can provide
it and avoid the lookup.
This change implements fix#3 from the above list; i.e. make
dmu_objset_find_dp() provide the name of the dataset so that we don't
have to search for it.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prashanth Sreenivasa <prashksp@gmail.com>
Reviewed-by: David Quigley <david.quigley@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7606
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cac6babCloses#5662
When doing recv and rollback, dsl_dataset_clone_swap_sync_impl will be
called to swap out the ds_objset and do dmu_objset_evict on the old one.
However, currently zv->zv_objset will not be swapped out accordingly, so
if anyone currently holds a fd on the zvol, we risk hitting a use-after-free.
We fix this by introducing the suspend and resume mechanism of zsb to
zv. Before recv or rollback, we use zvol_suspend to block all access to
zv_objset and shut it down. After the recv or rollback, we use zvol_resume
to swap in zv_objset with the new ds_objset and unblock the access.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#4866Closes#5609
Porting notes:
- This issue was first fixed in ZoL by commit d862cb0d. That fix was
then modified and an equivalent version of the patch landed in the
upstream code base. For additional details see the discussion in
https://github.com/openzfs/openzfs/pull/24 .
This commit aligns ZoL with OpenZFS codebase.
Authored by: Andriy Gapon <avg@icyb.net.ua>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Ned Bass <bass6@llnl.gov>
Reviewed by: Tim Chase <tim@chase2k.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: George Melikov mail@gmelikov.ru
OpenZFS-issue: https://www.illumos.org/issues/6529
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/e7e978bCloses#5606
Two threads send_traverse_thread() and receive_writer_thread() should
end with thread_exit();
Mostly a cosmetic issue under IllumOS.
Authored by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7659
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a569268Closes#5603
Authored by: Igor Kozhukhov ikozhukhov@gmail.com
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7071
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/25f7d99Closes#5597
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/7082
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/10e67aaCloses#5596
SLAB_USERCOPY flag was used to indicate PAX
not to kill copies from kernel to userland.
With recent grsecurity patchset and
CONFIG_GRKERNSEC_HIDESYM that enables
CONFIG_PAX_USERCOPY zfs would panic.
Handle newer API while keeping old one functional.
Tested-by: RageLtMan <rageltman@sempervictus>
Reviewed-by: spendergrsec <spender@grsecurity.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kevin Tanguy <kevin.tanguy@ovh.net>
Closes#595
Fix dmu_object_next() to correctly handle unallocated objects on
large_dnode datasets.
We implement this by scanning the dnode block until we find the correct
offset to be used in dnode_next_offset(). This is necessary because we
can't assume *objectp is a hole even if dmu_object_info() returns
ENOENT.
This fixes a couple of issues with zfs receive on large_dnode datasets.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5027Closes#5532
Authored by: Andriy Gapon <andriy.gapon@clusterhq.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gordon.w.ross@gmail.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/7181
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/90f2c09Closes#5585
Assuming /bin/cp causes problems on systems where cp is
not in /bin such as NixOS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Joerg Thalheim <joerg@higgsboson.tk>
Closes#5548
Add *_by_dnode() routines for accessing objects given their
dnode_t *, this is more efficient than accessing the object by
(objset_t *, uint64_t object). This change converts some but
not all of the existing consumers. As performance-sensitive
code paths are discovered they should be converted to use
these routines.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alex Zhuravlev <bzzz@whamcloud.com>
Closes#5534
Issue #4802
When building SPL within the kernel tree, C99 initializers cause
build failures and need to be converted to C89 as kernel CFLAGS
specify -std=gnu89.
This fix was provided by @behlendorf in #595 discussion notes and
manually implemented in the current master revision.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: RageLtMan <rageltman@sempervictus>
Closes#597
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Joe Stein <jas14@cs.brown.edu>
Ported-by: Don Brady <don.brady@intel.com>
When loading a pool that had been created before the existance of
per-vdev zaps, on a system that knows about per-vdev zaps, the
per-vdev zaps will not be allocated and initialized.
This appears to be because the logic that would have done so, in
spa_sync_config_object(), is not reached under normal operation. It is
only reached if spa_config_dirty_list is non-empty.
The fix is to add another `AVZ_ACTION_` enum that will allow this code
to be reached when we detect that we're loading an old pool, even when
there are no dirty configs.
OpenZFS-issue: https://www.illumos.org/issues/7743
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/e2d29d0Closes#5582
This change introduces a new weighting algorithm to improve
metaslab selection. The new weighting algorithm relies on the
SPACEMAP_HISTOGRAM feature. As a result, the metaslab weight
now encodes the type of weighting algorithm used (size-based
vs segment-based).
Porting Notes: The metaslab allocation tracing code is conditionally
removed on linux (dependent on mdb debugger).
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Chris Siden <christopher.siden@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <paul.dagnelie@delphix.com>
Reviewed by: Pavel Zakharov pavel.zakharov@delphix.com
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Don Brady <don.brady@intel.com>
OpenZFS-issue: https://www.illumos.org/issues/7303
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d5190931bdCloses#5404
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
[bio] The req_op enum was changed to req_opf. Update the "Linux 4.8 API"
autotools checks to use an int to determine whether the various REQ_OP
values are defined. This should work properly on kernels >= 4.8.
[bio] bio_set_op_attrs() is now an inline function and can't be detected
with #ifdef. Add a configure check to determine whether bio_set_op_attrs()
is defined. Move the local definition of it from vdev_disk.c to
blkdev_compat.h for consistency with other related compability shims.
[bio] The read/write flags and their modifiers, including WRITE_FLUSH,
WRITE_FUA and WRITE_FLUSH_FUA have been removed from fs.h. Add the new
bio_set_flush() compatibility wrapper to replace VDEV_WRITE_FLUSH_FUA
and set the flags appropriately for each supported kernel version.
[vfs] The generic_readlink() function has been made static. If .readlink
in inode_operations is NULL, generic_readlink() is used.
[zol typo] Completely unrelated to 4.10 compat, fix a typo in the check
for REQ_OP_SECURE_ERASE so that the proper macro is defined:
s/HAVE_REQ_OP_SECURE_DISCARD/HAVE_REQ_OP_SECURE_ERASE/
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5499
Fix a regression accidentally introduced by e0ab3ab.
Additionally, add a new script zpool_import_014_pos.ksh to
the ZFS test suite to exercise 'zpool import -t' functionality.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5466Closes#5515
The introduction of parallel zvol prefetch causes deadlock when using
vdev_file.
spa_async->(spa_namespace_lock)->txg_wait_synced->(wait for txg_sync)
txg_sync->zio_wait->(wait for vdev_file_io_fsync on system_taskq)
zvol_prefetch_minors_impl (on system_taskq)->spa_open_common->(wait for spa_namespace_lock)
We fix this by using dedicated taskq for vdev_file. This same change
was originally made in commit bc25c93 but reverted in commit aa9af22
when dynamic taskqs were added.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Closes#5506Closes#5495
When iterating over the input nvlist in dsl_props_set_sync_impl() when we don't
preserve the nvpair name before looking up ZPROP_VALUE, so when we later go to
process it nvpair_name() is always "value" and not the actual property name.
This fixes a couple of bugs in zfs_ioc_recv():
* Received properties were not restored correctly when failing to receive an
incremental send stream
* Received properties were not completely replaced by the new ones when
successfully receiving an incremental send stream
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5497
This branch contains the following fixes/improvements.
* Fix setting i_flags
* Fix wrong operator in xvattr.h
* Fix fchange macro in zpl_ioctl_setflags()
* Added configure check to use inode_set_flags()
* Added a test case for chattr for better test coverage
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5486Closes#5470Closes#5469
The main complication from the RT patch set is that the RW semaphore
locks change such that read locks on an rwsem can be taken only by
a single thread. All other threads are locked out. This single
thread can take a read lock multiple times though. The underlying
implementation changes to a mutex with an additional read_depth
count.
The implementation can be best understood by inspecting the RT
patch. rwsem_rt.h and rt.c give the best insight into how RT
rwsem works. My implementation for rwsem_tryupgrade is basically
an inversion of rt_downgrade_write found in rt.c. Please see the
comments in the code.
Unfortunately, I have to drop SPLAT rwlock test4 completely as this
test tries to take multiple locks from different threads, which RT
rwsems do not support. Otherwise SPLAT, zconfig.sh, zpios-sanity.sh
and zfs-tests.sh pass on my Debian-testing VM with the kernel
linux-image-4.8.0-1-rt-amd64.
Tested-by: kernelOfTruth <kerneloftruth@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Clemens Fruhwirth <clemens@endorphin.org>
Closes zfsonlinux/zfs#5491
Closes#589Closes#308
zfs_sb_create would normally takes ownership of zmo, and it will be freed in
zfs_sb_free. However, when zfs_sb_create fails we need to explicit free it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5490Closes#5496
The fchange in zpl_ioctl_setflags was for detecting flag change. However it
was incorrect and would always fail to detect a flag change from set to unset,
causing users without CAP_LINUX_IMMUTABLE to be able to unset flags.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Adapt avx512bw implementation for use with abd buffers. Mul2 implementation
is rewritten to take advantage of the BW instruction set.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Romain Dolbeau <romain.dolbeau@atos.net>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5477
Refactor the code by making splat_test_{init,fini}, splat_subsystem_{init,fini}
into functions. They don't have reason to be macro and it would be too bloated
to inline every call.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Fix zfs_xvattr_set to set S_IMMUTABLE and S_APPEND flags correctly.
Reinstate zfs_set_inode_flags and use it when zfs_xvatter_set and also when
setting up inode in zfs_znode_alloc and zfs_rezget.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
User of ida needs to call ida_destroy after using it. Otherwise
ida->free_bitmap and/or other stuff may leak.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5484
This removes two large whitespaces in "modinfo zfs" as well as correcting
a couple typos.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#5475
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Don't count '@' for dataset namelen if not a snapshot. This
fixes making a pool unimportable when the dataset namelen
is 255.
Add test file for zfs create name length 255.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5432Closes#5456
CID 154617: Memory - illegal accesses (UNINIT)
The value here just needs to be initialized to make Coverity happy.
When dsize == 0, then value of daiter.iter_mapaddr is irrelevant. That
address won't be accessed, it's only used for some arithmetic. dsize
can be zero either if dabd is null, or if code column is longer than the
current data column.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5437
Speed up import and export speed by:
* Add system delay taskq
* Parallel prefetch zvol dnodes during zvol_create_minors
* Parallel zvol_free during zvol_remove_minors
* Reduce list linear search using ida and hash
Reviewed-by: Boris Protopopov <boris.protopopov@actifio.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5433
Add a dedicated system_delay_taskq for long delay like spa_deadman and
zpl_posix_acl_free. This will allow us to use system_taskq in the manner of
dispatch multiple tasks and call taskq_wait_outstanding.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#588
Enable zio_dva_throttle_enabled=1 by default. Subsequent
testing has been unable to reproduce the suspected regression.
Tested-by: kernelOfTruth kerneloftruth@gmail.com
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf behlendorf1@llnl.gov
Reverts #5335Closes#5289Closes#5457
Save and reuse ddt dspace calculation when there have been no ddt changes.
This avoids unnecessary traversal of 168KiB of ddt histograms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5425
It was observed that even when the txg history is disabled by
setting `zfs_txg_history=0` the txg_sync thread still fetches
the vdev stats unnecessarily.
This patch refactors the code such that vdev_get_stats() is no
longer called when `zfs_txg_history=0`. And it further reduces
the differences between upstream and the ZoL txg_sync_thread()
function.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5412
On some kernel version, blk_cleanup_queue and put_disk will wait for more then
10ms. So a pool with a lot of zvols will easily wait for more then 1 min if we
do zvol_free sequentially.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Requires-spl: refs/pull/588/head
Do parallel prefetch all zvol dnodes before actually creating each individual.
This will greatly reduce the import time when having a lot of zvols and disk
is slow.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
dbuf_read() creates a zio_root() to track and wait for all the
zio's that may happen as part of this call. However, if the blkptr_t
for this buffer is NULL or a hole, we will not create any more zio's,
so this zio_root() is unnecessary. This is always the case when calling
dbuf_read() on a bonus buffer, because it has no blkptr (it's part of
the containing dnode). For workloads that read a lot of bonus buffers
(e.g. file creation and removal), creating and destroying these
unnecessary zio's can decrease performance by around 3%.
The fix is to only create/destroy the zio_root() in dbuf_read() if
the blkptr is not NULL and not a hole.
Changes sponsored by Intel Corp.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Zhuravlev <alexey.zhuravlev@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue openzfs/openzfs#137
Closes#4803Closes#5382
This should be & and not | so is_metadata is set correctly.
Reviewed-by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5438
It looks like this was functionality which was added in the
original SA implementation and then never needed. It can
be safely removed now and easily added back if we find a
use for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Closes#5440
zio.h includes zio_impl.h but zio_impl.h also includes zio.h, so the
header files to contain each other. Get rid of the zio_impl.h include
in zio.h and update zio_inject.c to include zio.h instead of zio_impl.h.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Closes#5439
Use it for spa_deadman, zpl_posix_acl_free, snapentry_expire.
This free system_taskq from the above long delay tasks, and allow us to do
taskq_wait_outstanding on system_taskq without being blocked forever, making
system_taskq more generic and useful.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
To prevent holding tq_lock for too long.
Before zfsonlinux/zfs@8e71ab9, hogging delay tasks and cat /proc/spl/taskq
would easily cause a lockup. While that bug has been fixed. It's probably
still a good idea to do this just in case task lists grow too large.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#586
In multiple cases zio_buf_alloc() was used instead of kmem_alloc()
or vmem_alloc(). This was often done because the allocations
could be large and it was easy to use zfs_buf_alloc() for them.
But this isn't ideal for allocations which are small or short
lived. In these cases it is better to use kmem_alloc() or
vmem_alloc(). If possible we want to avoid the case where
we have slabs allocated for kmem caches which are rarely used.
Note for small allocations vmem_alloc() will be internally
converted to kmem_alloc(). Therefore as long as large
allocations are infrequent and short lived the penalty for
using vmem_alloc() is small.
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5409
* Convert ABD to use the Linux Kernel scatterlist implementation
instead of the hand rolled one from illumos.
* Scatter ABDs are preferentially populated with higher order
compound pages from a single zone. Allocation size is
progressively decreased until it can be satisfied without
performing reclaim or compaction.
* An alternate page allocator is provided for kernels older
than 3.6 and for CONFIG_HIGHMEM systems. This allocator
is designed as a fallback for maximum compatibility.
* Extended abdstats to provide visibility in the the allocator.
* Add cached value for PAGESIZE in userspace.
Contributions-by:
Chunwei Chen <david.chen@osnexus.com>
Gvozden Neskovic <neskovic@gmail.com>
Jinshan Xiong <jinshan.xiong@intel.com>
Isaac Huang <he.huang@intel.com>
David Quigley <david.quigley@intel.com>
Brian Behlendorf <behlendorf1@llnl.gov>
Enable vectorized raidz code on ABD buffers. The avx512f,
avx512bw, neon and aarch64_neonx2 are disabled in this commit.
With the exception of avx512bw these implementations are
updated for ABD in the subsequent commits.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
* userspace: aligned buffers. Minimum of 32B alignment is
needed for AVX2. Kernel buffers are aligned 512B or more.
* add abd_get_offset_size() interface
* abd_iter_map(): fix calculation of iter_mapsize
* add abd_raidz_gen_iterate() and abd_raidz_rec_iterate()
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Linux kernel commit 723c038475b78 removed this field.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#5393
CID 147540: unsigned_compare
- Cast nsec to a int32_t to properly detect the expected overflow.
CID 147542: unsigned_compare
- intval can never be less than ZIO_FAILURE_MODE_WAIT which is
defined to be zero. Remove this useless check.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Closes#5379
It's used by Lustre to determine if the objset can be upgraded.
The inline version doesn't work because dmu_objset_is_snapshot()
is not exported.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Closes#5385
Linux 3.14 introduces inode->set_acl(). Normally, acl modification will come
from setxattr, which will handle by the acl xattr_handler, and we already
handles that well. However, nfsd will directly calls inode->set_acl or
return error if it doesn't exists.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Massimo Maggi <me@massimo-maggi.eu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5371Closes#5375
The phase 2 work primarily entails the Diagnosis Engine and
the Retire Agent modules. It also includes infrastructure
to support a crude FMD environment to host these modules.
The Diagnosis Engine consumes I/O and checksum ereports and
feeds them into a SERD engine which will generate a corres-
ponding fault diagnosis when the SERD engine fires. All the
diagnosis state data is collected into cases, one case per
vdev being tracked.
The Retire Agent responds to diagnosed faults by isolating
the faulty VDEV. It will notify the ZFS kernel module of
the new VDEV state (degraded or faulted). This agent is
also responsible for managing hot spares across pools.
When it encounters a device fault or a device removal it
replaces the device with an appropriate spare if available.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Closes#5343
Currently every calls to zpl_posix_acl_release will schedule a delayed task,
and each delayed task will add a timer. This used to be fine except for
possibly bad performance impact.
However, in Linux 4.8, a new timer wheel implementation[1] is introduced. In
this new implementation, the larger the delay, the less accuracy the timer is.
So when we have a flood of timer from zpl_posix_acl_release, they will expire
at the same time. Couple with the fact that task_expire will do linear search
with lock held. This causes an extreme amount of contention inside interrupt
and would actually lockup the system.
We fix this by doing batch free to prevent a flood of delayed task. Every call
to zpl_posix_acl_release will put the posix_acl to be freed on a lockless
list. Every batch window, 1 sec, the zpl_posix_acl_free will fire up and free
every posix_acl that passed the grace period on the list. This way, we only
have one delayed task every second.
[1] https://lwn.net/Articles/646950/
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Only restrict the maximum zio alloc size to 32-bit kernel space.
The same virtual address space limitations don't apply to user
space. This resolves a memory allocation failure in raidz_test
where it expects to be able to exercises all valid zio sizes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This is the Fletcher4 algorithm implemented in pure C, but using
multiple counters using algorithms identical to those used for
SSE/NEON and AVX2.
This allows for faster execution on core with strong superscalar
capabilities but weak SIMD capabilities.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#5317
Linux 3.11 add O_TMPFILE to open(2), which allow creating an unlinked file on
supported filesystem. It's basically doing open(2) and unlink(2) atomically.
The filesystem support is added through i_op->tmpfile. We basically copy the
create operation except we get rid of the link and name related stuff and add
the new node to unlinked set.
We also add support for linkat(2) to link tmpfile. However, since all previous
file operation will skip ZIL, we force a txg_wait_synced to make sure we are
sync safe.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Currently, doing things like fsetxattr(2) on an unlinked file will result in
ENODATA. There's two places that cause this: zfs_dirent_lock and zfs_zget.
The fix in zfs_dirent_lock is pretty straightforward. In zfs_zget though, we
need it to not return error when the zp is unlinked. This is a pretty big
change in behavior, but skimming through all the callers, I don't think this
change would cause any problem. Also there's nothing preventing z_unlinked
from being set after the z_lock mutex is dropped before but before zfs_zget
returns anyway.
The rest of the stuff is to make sure we don't log xattr stuff when owner is
unlinked.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
avx512f should work on all AVX512 hardware, since it only uses
Foundation instructions.
avx512bw should be faster on hardware supporting the AVW512BW
extension. We can use full-width pshufb (instead of relying on the 256
bits AVX2 pshufb). As a side-effect, the code is also unrolled more.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.github@dolbeau.name>
Closes#5219
On error dsl_prop_get_all_ds() does not free the nvlist it allocates.
This behavior may have been intentional when originally written
but is atypical and often confusing. Since no callers rely on this
behavior the function has been updated to always free the nvlist
on error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: BearBabyLiu <liu.huang@zte.com.cn>
Closes#5320
On 32-bit Linux systems use vmem_size() to correctly size the ARC
and better determine when IO should be throttle due to low memory.
On 64-bit systems this change has no effect since the virtual
address space available far exceeds the physical memory available.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5347
A limit of 1TB exists for zvols on 32-bit systems. Update the code
to correctly reflect this limitation in a similar manor as the
OpenZFS implementation.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5347
Originally the .zfs/snapshot directory was disabled for 32-bit systems
because 64-bit inode numbers were not supported. This is no longer
the case and this functionality can be enabled by default.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5347Closes#2002
Add the TASKQID_INVALID macros and update callers to use the macro
instead of testing against 0. There is no functional change
even though the functions in zfs_ctldir.c incorrectly used -1
instead of 0.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5347
Add the TASKQID_INVALID and TASKQID_INITIAL macros and update the
taskq implementation and test cases to use them. This is solely
for the purposes of readability and introduces no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add a minimal implementation of vmem_size() which accounts for the
virtual memory usage of the SPL's kmem cache. This functionality
is only useful on 32-bit systems with a small virtual address space.
The following assumptions are made:
1) The major SPL consumer of virtual memory is the kmem cache.
2) Memory allocated with vmem_alloc() is short lived and can be ignored.
3) Allow a 4MB floor as a generous pad given normal consumption.
4) The spl_kmem_cache_sem only contends with cache create/destroy.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Replace magic value 16 with ARRAY_SIZE() to correctly handle
when the sa_legacy_attrs array size changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: cao.xuewen <cao.xuewen@zte.com.cn>
Closes#5354
CID 147509: Explicit null dereferenced
- l2arc_sublist_lock is fragile as relied on caller too much.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Closes#5319
Ubuntu added support for checking inode permissions to lookup_bdev() in kernel
commit 193fb6a2c94fab8eb8ce70a5da4d21c7d4023bee (merged in 4.4.0-6.21).
Upstream bug: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1636517
This patch adds a test for Ubuntu's variant of lookup_bdev() to configure and
calls the function in the correct way.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Closes#5336
Until it can be determined definitively that a performance
regression wasn't introduced accidentally by 3dfb57a this
functionality is being disabled by default. It can be re-
enabled by setting zio_dva_throttle_enabled=1.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5335
Issue #5289
- Fix autoreplace behaviour on statechange-led.sh script.
ZED sends the following events on an auto-replace:
1. statechange: Disk goes UNAVAIL->ONLINE
2. statechange: Disk goes ONLINE->UNAVAIL
3. vdev_attach: Disk goes ONLINE
Events 1-2 happen when ZED first attempts to do an auto-online. When that
fails, ZED then tries an auto-replace, generating the vdev_attach event in #3.
In the previous code, statechange-led was only looking at the UNAVAIL->ONLINE
transition to turn off the LED. It ignored the #2 ONLINE->UNAVAIL transition,
assuming it was just the "old" VDEV going offline. This is problematic, as
a drive can go from ONLINE->UNAVAIL when it's malfunctioning, and we don't want
to ignore that.
This new patch correctly turns on the fault LED every time a drive becomes
UNAVAIL. It also monitors vdev_attach events to trigger turning off the LED
when an auto-replaced disk comes online.
- Remove unnecessary libdevmapper warning with --with-config=kernel
This fixes an unnecessary libdevmapper warning when building
--with-config=kernel. Kernel code does not use libdevmapper, so the warning
is not needed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2375Closes#5312Closes#5331
Similar to commit a3600a106. Asm files need an explicit note
that they do not require an executable stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason Zaman <jason@perfinion.com>
Closes#5332
This is caught by kmemleak when running compress_004_pos
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#5244Closes#5330
When creating and destroying pools in tight loop it's possible to
exhaust the number of allowed threads on a system. This results
in taskq_create() failling and a NULL dereference.
Resolve the issue by falling back to opening the vdevs all
synchronously.
Reviewed-by: Denys Rtveliashvili <denys@rtveliashvili.name>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/spl#521
Closes#4637
Previously when a drive faulted, the statechange-led.sh script would lookup
the drive's LED sysfs entry in /sys/block/sd*/device/enclosure_device, and
turn it on. During testing we noticed that if you pulled out a drive, or if
the drive was so badly broken that it no longer appeared to Linux, that the
/sys/block/sd* path would be removed, and the script could not lookup the
LED entry.
To fix this, this patch looks up the disks's more persistent
"/sys/class/enclosure/X:X:X:X/Slot N" LED sysfs path at pool import. It then
passes that path to the statechange-led script to use, rather than having the
script look it up on the fly. This allows the script to turn on/off the slot
LEDs even when the drive is missing.
Closes#5309Closes#2375
This is not useful on micro-architecture with a weak NEON
implementation (only 64 bits); the native version is slower &
the byteswap barely faster than scalar. On A53 or A57, it's
a small improvement on scalar but OK for byteswap.
Results from an A53 system:
0 0 0x01 -1 0 1499068294333000 1499101101878000
implementation native byteswap
scalar 1008227510 755880264
aarch64_neon 1198098720 1044818671
fastest aarch64_neon aarch64_neon
Results from a A57 system:
0 0 0x01 -1 0 4407214734807033 4407233933777404
implementation native byteswap
scalar 2302071241 1124873346
aarch64_neon 2542214946 2245570352
fastest aarch64_neon aarch64_neon
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#5248
The AVL tree compare function requires that either -1, 0, or 1 be
returned. However the strcmp() function only guarantees that a
negative, zero, or positive value is returned. Therefore, the
return value of strcmp() needs to be sanitized with AVL_ISIGN.
This was initially overlooked because the x86_64 implementation
of strcmp() happens to only returns the allowed values. This
was observed on an aarch64 platform which behaves correctly but
differently as described above.
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5311Closes#5313
In torvalds/linux@31051c8 the inode_change_ok() function was
renamed setattr_prepare() and updated to take a dentry ratheri
than an inode. Update the code to call the setattr_prepare()
and add a wrapper function which call inode_change_ok() for
older kernels.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Requires-spl: refs/pull/581/head
In Linux 4.9, torvalds/linux@fd50eca, iops->{set,get,remove}xattr and
generic_{set,get,remove}xattr are removed. xattr operations will directly
go through sb->s_xattr.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
In Linux 4.9, torvalds/linux@2773bf0, iops->rename() and iops->rename2() are
merged together into iops->rename(), it now wants flags.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
These operations are dir specific, there's no point putting them in
zpl_inode_operations which is for regular files.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
In Linux 4.9, torvalds/linux@81243ea, group_info changed from 2d array via
->blocks to 1d array via ->gid. We change the spl cred functions accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#581
No need to crhold current_cred(), fix possible leak in splat_cred_test2
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#556
init_groups has 0 nblocks, therefore calling the current crgetgroups with
init_groups would result in out-of-bound access. We fix this by returning NULL
when nblocks is 0.
Cap crgetngroups to NGROUPS_PER_BLOCK, since crgetgroups will only return
blocks[0].
Also, remove all get_group_info. The cred already holds reference on the
group_info, and cred is not mutable. So there's no reason to hold extra
reference, if we hold cred.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#556
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
CID 150926: Unchecked return value (CHECKED_RETURN)
- This case cannot occur given the existing taskq implementation
and flags passed to task_dispatch().
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5272
Accidentally introduced by 3dfb57a, when building with debugging
disabled several variables are unused. Resolve this by wrapping
them in ASSERTV to remove them for non-debug builds.
Reviewed by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5284
CID 150924: Unchecked return value (CHECKED_RETURN)
- On taskq_dispatch failure the reference must be dropped and
this entry can be safely skipped. This case should be impossible
in the existing implementation but should be handled regardless.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5278
OpenZFS 7090 - zfs should throttle allocations
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <paul.dagnelie@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Ported-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
When write I/Os are issued, they are issued in block order but the ZIO
pipeline will drive them asynchronously through the allocation stage
which can result in blocks being allocated out-of-order. It would be
nice to preserve as much of the logical order as possible.
In addition, the allocations are equally scattered across all top-level
VDEVs but not all top-level VDEVs are created equally. The pipeline
should be able to detect devices that are more capable of handling
allocations and should allocate more blocks to those devices. This
allows for dynamic allocation distribution when devices are imbalanced
as fuller devices will tend to be slower than empty devices.
The change includes a new pool-wide allocation queue which would
throttle and order allocations in the ZIO pipeline. The queue would be
ordered by issued time and offset and would provide an initial amount of
allocation of work to each top-level vdev. The allocation logic utilizes
a reservation system to reserve allocations that will be performed by
the allocator. Once an allocation is successfully completed it's
scheduled on a given top-level vdev. Each top-level vdev maintains a
maximum number of allocations that it can handle (mg_alloc_queue_depth).
The pool-wide reserved allocations (top-levels * mg_alloc_queue_depth)
are distributed across the top-level vdevs metaslab groups and round
robin across all eligible metaslab groups to distribute the work. As
top-levels complete their work, they receive additional work from the
pool-wide allocation queue until the allocation queue is emptied.
OpenZFS-issue: https://www.illumos.org/issues/7090
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/4756c3d7Closes#5258
Porting Notes:
- Maintained minimal stack in zio_done
- Preserve linux-specific io sizes in zio_write_compress
- Added module params and documentation
- Updated to use optimize AVL cmp macros
The ICP requires destructors to for each crypto module that is added.
These do not necessarily exist in Illumos because they assume that
these modules can never be unloaded from the kernel. Some of this
cleanup code was missed when #4760 was merged, resulting in leaks.
This patch simply fixes that.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #4760Closes#5265
Fix use after free in zfsctl_snapshot_unmount(). Use /usr/bin/env
instead of /bin/sh to fix a shell code injection flaw and allow use
with grsecurity.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Stian Ellingsen <stian@plaimi.net>
Closes#5250Closes#4377
This is as much an upstream compatibility as it's a bit of a performance
gain.
The illumos taskq implemention doesn't allow a TASKQ_THREADS_CPU_PCT type
to be dynamic and in fact enforces as much with an ASSERT.
As to performance, if this taskq is dynamic, it can cause excessive
contention on tq_lock as the threads are created and destroyed because it
can see bursts of many thousands of tasks in a short time, particularly
in heavy high-concurrency zvol write workloads.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#5236
When #4760 was merged tests were added to ensure that the new checksums
were working properly. However, some of the functionality for sha2
functions were not ported over, resulting in some Coverity defects and
code that would be unstable when needed in the future. This patch
simply ports over the missing code and fixes the defects in the
process.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue #4760Closes#5251
The following new test cases need to have execute permissions set:
userquota/groupspace_003_pos.ksh
userquota/userquota_013_pos.ksh
userquota/userspace_003_pos.ksh
upgrade/upgrade_userobj_001_pos.ksh
upgrade/setup.ksh
upgrade/cleanup.ksh
The following source files accidentally were marked executable:
lib/libzpool/kernel.c
lib/libshare/nfs.c
lib/libzfs/libzfs_dataset.c
lib/libzfs/libzfs_util.c
tests/zfs-tests/cmd/rm_lnkcnt_zero_file/rm_lnkcnt_zero_file.c
tests/zfs-tests/cmd/dir_rd_update/dir_rd_update.c
cmd/zed/zed_exec.c
module/icp/core/kcf_sched.c
module/zfs/dsl_pool.c
module/zfs/arc.c
module/nvpair/nvpair.c
man/man5/zfs-module-parameters.5
Reviewed-by: GeLiXin <ge.lixin@zte.com.cn>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5241
Call mount and umount via /usr/bin/env instead of /bin/sh in
zfsctl_snapshot_mount() and zfsctl_snapshot_unmount().
This change fixes a shell code injection flaw. The call to /bin/sh
passed the mountpoint unescaped, only surrounded by single quotes. A
mountpoint containing one or more single quotes would cause the command
to fail or potentially execute arbitrary shell code.
This change also provides compatibility with grsecurity patches.
Grsecurity only allows call_usermodehelper() to use helper binaries in
certain paths. /usr/bin/* is allowed, /bin/* is not.
OpenZFS decided that ignore_hole_birth was too imprecise and
incorrect a name (and went with send_holes_without_birth_time).
Rename it in ZoL too, while keeping the name "ignore_hole_birth"
pointing to the same variable for existing consumers.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#5239
When iterating per_cpu values, we need to use for_each_possible_cpu. While
NR_CPUS indicates the number of CPU supported by the kernel, it might not
initialize all of them if the kernel decides it's not possible to use them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Closes#578
Updating vd->vdev_parent->vdev_nonrot in vdev_open_child()
is a race when vdev_open_child is called for many children
from a task queue.
vdev_open_child() is only called by vdev_open_children(), let
the latter update the parent vdev_nonrot member. The update
was already there, so done twice previously. Thus using the
same logic at the end in vdev_open_children() to update
vdev_nonrot, either we are vdev_uses_zvols() or not.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5162
Fixes ABI issues with fletcher4 code, adds support for
incremental updates, and adds ztest method for testing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Closes#5164
Using a benchmark which creates 2 million files in one TXG, I observe
that the thread running spa_sync() is on CPU almost the entire time we
are syncing, and therefore can be a performance bottleneck. About 50% of
the time in spa_sync() is in dmu_objset_do_userquota_updates().
The problem is that dmu_objset_do_userquota_updates() calls
zap_increment_int(DMU_USERUSED_OBJECT) once for every file that was
modified (or created). In this benchmark, all the files are owned by the
same user/group, so all 2 million calls to zap_increment_int() are
modifying the same entry in the zap. The same issue exists for the
DMU_GROUPUSED_OBJECT.
We should keep an in-memory map from user to space delta while we are
syncing, and when we finish, iterate over the in-memory map and modify
the ZAP once per entry. This reduces the number of calls to
zap_increment_int() from "number of objects modified" to "number of
owners/groups of modified files".
This reduced the time spent in spa_sync() in the file create benchmark
by ~33%, from 11 seconds to 7 seconds.
Upstream bugs: DLPX-44799
Ported by: Ned Bass <bass6@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6988
ZFSonLinux-issue: https://github.com/zfsonlinux/zfs/issues/4642
OpenZFS-commit: unmerged
Porting notes:
- Added curly braces around declaration of userquota_cache_t cache to
quiet compiler warning;
- Handled the userobj accounting the same way it proposed in this path.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
This patch tracks dnode usage for each user/group in the
DMU_USER/GROUPUSED_OBJECT ZAPs. ZAP entries dedicated to dnode
accounting have the key prefixed with "obj-" followed by the UID/GID
in string format (as done for the block accounting).
A new SPA feature has been added for dnode accounting as well as
a new ZPL version. The SPA feature must be enabled in the pool
before upgrading the zfs filesystem. During the zfs version upgrade,
a "quotacheck" will be executed by marking all dnode as dirty.
ZoL-bug-id: https://github.com/zfsonlinux/zfs/issues/3500
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Johann Lombardi <johann.lombardi@intel.com>
Move the synchronization of inode/znode i_flgas/pflags into
the respective internal zfs function. This is mostly
mechanical work and shouldn't introduce any functional
changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nikolay Borisov <n.borisov.lkml@gmail.com>
Issue #227Closes#5223
Init, compute, and fini methods are changed to work on internal context object.
This is necessary because ABI does not guarantee that SIMD registers will be preserved
on function calls. This is technically the case in Linux kernel in between
`kfpu_begin()/kfpu_end()`, but it breaks user-space tests and some kernels that
don't require disabling preemption for using SIMD (osx).
Use scalar compute methods in-place for small buffers, and when the buffer size
does not meet SIMD size alignment.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Combine incrementally computed fletcher4 checksums. Checksums are combined
a posteriori, allowing for parallel computation on chunks to be implemented if
required. The algorithm is general, and does not add changes in each SIMD
implementation.
New test in ztest verifies incremental fletcher computations.
Checksum combining matrix for two buffers `a` and `b`, where `Ca` and `Cb` are
respective fletcher4 checksums, `Cab` is combined checksum, `s` is size of buffer
`b` (divided by sizeof(uint32_t)) is:
Cab[A] = Cb[A] + Ca[A]
Cab[B] = Cb[B] + Ca[B] + s * Ca[A]
Cab[C] = Cb[C] + Ca[C] + s * Ca[B] + s(s+1)/2 * Ca[A]
Cab[D] = Cb[D] + Ca[D] + s * Ca[C] + s(s+1)/2 * Ca[B] + s(s+1)(s+2)/6 * Ca[A]
NOTE: this calculation overflows for larger buffers. Thus, internally, the calculation
is performed on 8MiB chunks.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Due to changes in the task_struct the following warning is occurs
when initializing the global p0. Since this structure only exists
for it's address to be taken initialize it in a manor which isn't
sensitive to internal changes to the structure.
module/spl/spl-generic.c:58:1: error: missing braces around
initializer [-Werror=missing-braces]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#576
Authored by: ilovezfs <ilovezfs@icloud.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
In any pool without the extensible dataset feature flag already enabled,
creating a dataset with dedup set to use one of the new checksums would
result in the following panic as soon as any data was added:
panic[cpu0]/thread=ffffff0006761c40: feature_get_refcount(spa, feature,
&refcount) != 48 (0x30 != 0x30), file: ../../common/fs/zfs/zfeature.c
line 390
Inpsection showed that feature->fi_feature was 7, which is the value of
SPA_FEATURE_EXTENSIBLE_DATASET in the spa_feature enum. This commit
adds extensible dataset as a dependency for the sha512, edonr, and skein
feature flags, which prevents the panic.
OpenZFS-issue: https://www.illumos.org/issues/6585
OpenZFS-commit: 892586e8a1
Porting Notes:
This code was originally from Illumos, but I actually ported it from:
openzfsonosx/zfs@b62a652
Authored by: ilovezfs <ilovezfs@icloud.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Tony Hutter <hutter2@llnl.gov>
zio_checksum_to_feature() expects a zio_checksum enum not a raw property
intval, so the new checksums weren't being detected when the
ZIO_CHECKSUM_VERIFY flag got in the way.
Given a pool without feature@sha512,
zfs create -o dedup=sha512 naughty/fivetwelve_noverify_ds
would fail as expected since the raw intval would indeed be equal to
SPA_FEATURE_SHA512.
However,
zfs create -o dedup=sha512,verify naughty/fivetwelve_verify_ds
would incorrectly succeed because ZIO_CHECKSUM_VERIFY would be in the
way, the raw intval would not be a member of the enum, and
zio_checksum_to_feature() would return SPA_FEATURE_NONE, with the result
that spa_feature_is_enabled() would never be called.
This was first detected with edonr, since in that case verify is
required.
This commit clears the ZIO_CHECKSUM_VERIFY flag before calling
zio_checksum_to_feature() using the ZIO_CHECKSUM_MASK and verifies in
zio_checksum_to_feature() that ZIO_CHECKSUM_MASK has been applied by the
caller to attempt to prevent the same bug from occurring again in the
future.
OpenZFS-issue: https://www.illumos.org/issues/6541
OpenZFS-commit: 971640e6aa
Porting notes:
This code was originally from Illumos, but I actually ported it from:
openzfsonosx/zfs@bef06e1
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported by: Tony Hutter <hutter2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4185
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45818ee
Porting Notes:
This code is ported on top of the Illumos Crypto Framework code:
b5e030c8db
The list of porting changes includes:
- Copied module/icp/include/sha2/sha2.h directly from illumos
- Removed from module/icp/algs/sha2/sha2.c:
#pragma inline(SHA256Init, SHA384Init, SHA512Init)
- Added 'ctx' to lib/libzfs/libzfs_sendrecv.c:zio_checksum_SHA256() since
it now takes in an extra parameter.
- Added CTASSERT() to assert.h from for module/zfs/edonr_zfs.c
- Added skein & edonr to libicp/Makefile.am
- Added sha512.S. It was generated from sha512-x86_64.pl in Illumos.
- Updated ztest.c with new fletcher_4_*() args; used NULL for new CTX argument.
- In icp/algs/edonr/edonr_byteorder.h, Removed the #if defined(__linux) section
to not #include the non-existant endian.h.
- In skein_test.c, renane NULL to 0 in "no test vector" array entries to get
around a compiler warning.
- Fixup test files:
- Rename <sys/varargs.h> -> <varargs.h>, <strings.h> -> <string.h>,
- Remove <note.h> and define NOTE() as NOP.
- Define u_longlong_t
- Rename "#!/usr/bin/ksh" -> "#!/bin/ksh -p"
- Rename NULL to 0 in "no test vector" array entries to get around a
compiler warning.
- Remove "for isa in $($ISAINFO); do" stuff
- Add/update Makefiles
- Add some userspace headers like stdio.h/stdlib.h in places of
sys/types.h.
- EXPORT_SYMBOL *_Init/*_Update/*_Final... routines in ICP modules.
- Update scripts/zfs2zol-patch.sed
- include <sys/sha2.h> in sha2_impl.h
- Add sha2.h to include/sys/Makefile.am
- Add skein and edonr dirs to icp Makefile
- Add new checksums to zpool_get.cfg
- Move checksum switch block from zfs_secpolicy_setprop() to
zfs_check_settable()
- Fix -Wuninitialized error in edonr_byteorder.h on PPC
- Fix stack frame size errors on ARM32
- Don't unroll loops in Skein on 32-bit to save stack space
- Add memory barriers in sha2.c on 32-bit to save stack space
- Add filetest_001_pos.ksh checksum sanity test
- Add option to write psudorandom data in file_write utility
Tobin Harding
Fabian Grünbichler
Brian Behlendorf
Olaf Faaland
Isaac Huang
Ned Bass
Alek P
chrisrd
DeHackEd
Richard Elling
Feng Sun
Giuseppe Di Natale
Gaurav Kumar
Arkadiusz Bubała
LOLi
Richard Lowe
Gvozden Neskovic
Eli Rosenthal
Steve Dougherty
Andriy Gapon
Matthew Ahrens
dbavatar
Tom Caputi
Chunwei Chen
Don Brady
sanjeevbagewadi
Boris Protopopov
Tony Hutter
Andriy Gapon
Oleg Drokin
Dave Eddy
Yuri Pankov
alaviss
Boris Protopopov
Morgan Jones
Don Brady
Richard Yao
Richard Yao
Paul Dagnelie
Chunwei Chen
Alan Somers
Christian Schwarz
RageLtMan
Debabrata Banerjee
jxiong
Dan Kimmel
wli5
DHE
Giuseppe Di Natale
George Wilson
Steven Hartland
N Clark
Daniel Hoffman
Andriy Gapon
Tim Chase
George Melikov
David Quigley
clefru
Kevin Tanguy
Jörg Thalheim
bzzz77
RageLtMan
ka7
bunder2015
luozhengzheng
cao
Romain Dolbeau
David Quigley
Romain Dolbeau
BearBabyLiu
Ubuntu
GeLiXin
Hajo Möller
Jason Zaman
Stian Ellingsen
Håkan Johansson
Jinshan Xiong
lorddoskias
ilovezfs