a1d477c24c
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1eb
Closes #6900
|
||
|---|---|---|
| .. | ||
| runfiles | ||
| test-runner | ||
| zfs-tests | ||
| Makefile.am | ||
| README.md | ||
README.md
ZFS Test Suite README
- Building and installing the ZFS Test Suite
The ZFS Test Suite runs under the test-runner framework. This framework is built along side the standard ZFS utilities and is included as part of zfs-test package. The zfs-test package can be built from source as follows:
$ ./configure
$ make pkg-utils
The resulting packages can be installed using the rpm or dpkg command as appropriate for your distributions. Alternately, if you have installed ZFS from a distributions repository (not from source) the zfs-test package may be provided for your distribution.
- Installed from source
$ rpm -ivh ./zfs-test*.rpm, or
$ dpkg -i ./zfs-test*.deb,
- Installed from package repository
$ yum install zfs-test
$ apt-get install zfs-test
- Running the ZFS Test Suite
The pre-requisites for running the ZFS Test Suite are:
- Three scratch disks
- Specify the disks you wish to use in the $DISKS variable, as a space delimited list like this: DISKS='vdb vdc vdd'. By default the zfs-tests.sh sciprt will construct three loopback devices to be used for testing: DISKS='loop0 loop1 loop2'.
- A non-root user with a full set of basic privileges and the ability to sudo(8) to root without a password to run the test.
- Specify any pools you wish to preserve as a space delimited list in the $KEEP variable. All pools detected at the start of testing are added automatically.
- The ZFS Test Suite will add users and groups to test machine to verify functionality. Therefore it is strongly advised that a dedicated test machine, which can be a VM, be used for testing.
Once the pre-requisites are satisfied simply run the zfs-tests.sh script:
$ /usr/share/zfs/zfs-tests.sh
Alternately, the zfs-tests.sh script can be run from the source tree to allow developers to rapidly validate their work. In this mode the ZFS utilities and modules from the source tree will be used (rather than those installed on the system). In order to avoid certain types of failures you will need to ensure the ZFS udev rules are installed. This can be done manually or by ensuring some version of ZFS is installed on the system.
$ ./scripts/zfs-tests.sh
The following zfs-tests.sh options are supported:
-v Verbose zfs-tests.sh output When specified additional
information describing the test environment will be logged
prior to invoking test-runner. This includes the runfile
being used, the DISKS targeted, pools to keep, etc.
-q Quiet test-runner output. When specified it is passed to
test-runner(1) which causes output to be written to the
console only for tests that do not pass and the results
summary.
-x Remove all testpools, dm, lo, and files (unsafe). When
specified the script will attempt to remove any leftover
configuration from a previous test run. This includes
destroying any pools named testpool, unused DM devices,
and loopback devices backed by file-vdevs. This operation
can be DANGEROUS because it is possible that the script
will mistakenly remove a resource not related to the testing.
-k Disable cleanup after test failure. When specified the
zfs-tests.sh script will not perform any additional cleanup
when test-runner exists. This is useful when the results of
a specific test need to be preserved for further analysis.
-f Use sparse files directly instread of loopback devices for
the testing. When running in this mode certain tests will
be skipped which depend on real block devices.
-d DIR Create sparse files for vdevs in the DIR directory. By
default these files are created under /var/tmp/.
-s SIZE Use vdevs of SIZE (default: 4G)
-r RUNFILE Run tests in RUNFILE (default: linux.run)
The ZFS Test Suite allows the user to specify a subset of the tests via a runfile. The format of the runfile is explained in test-runner(1), and the files that zfs-tests.sh uses are available for reference under /usr/share/zfs/runfiles. To specify a custom runfile, use the -r option:
$ /usr/share/zfs/zfs-tests.sh -r my_tests.run
- Test results
While the ZFS Test Suite is running, one informational line is printed at the
end of each test, and a results summary is printed at the end of the run. The
results summary includes the location of the complete logs, which is logged in
the form /var/tmp/test_results/[ISO 8601 date]. A normal test run launched
with the zfs-tests.sh wrapper script will look something like this:
$ /usr/share/zfs/zfs-tests.sh -v -d /mnt
--- Configuration --- Runfile: /usr/share/zfs/runfiles/linux.run STF_TOOLS: /usr/share/zfs/test-runner STF_SUITE: /usr/share/zfs/zfs-tests FILEDIR: /mnt FILES: /mnt/file-vdev0 /mnt/file-vdev1 /mnt/file-vdev2 LOOPBACKS: /dev/loop0 /dev/loop1 /dev/loop2 DISKS: loop0 loop1 loop2 NUM_DISKS: 3 FILESIZE: 4G Keep pool(s): rpool
/usr/share/zfs/test-runner/bin/test-runner.py -c
/usr/share/zfs/runfiles/linux.run -i /usr/share/zfs/zfs-tests
Test: .../tests/functional/acl/posix/setup (run as root) [00:00] [PASS]
...470 additional tests...
Test: .../tests/functional/zvol/zvol_cli/cleanup (run as root) [00:00] [PASS]
Results Summary PASS 472
Running Time: 00:45:09 Percent passed: 100.0% Log directory: /var/tmp/test_results/20160316T181651