Calling uiomove() in mappedread() under the page lock can result
in a deadlock if the user space page needs to be faulted in.
Resolve the issue by dropping the page lock before the uiomove().
The inode range lock protects against concurrent updates via
zfs_read() and zfs_write().
Reviewed-by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7335Closes#7339
RHEL/CentOS 6 supports sys/xattr.h eliminating the need for
libattr-devel as a dependency.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7344Closes#7351
The changes piggyback JSON output support on top of channel programs
(#6558). This way the JSON output support is targeted to scripting
use cases and is easily maintainable since it really only touches
one function (zfs_do_channel_program()).
This patch ports Joyent's JSON nvlist library from illumos to enable
easy JSON printing of channel program output nvlist. To keep the
delta small I also took advantage of the fact that printing in
zfs_do_channel_program() was almost always done before exiting
the program.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7281
ZFS Performance test concurrency should be lowered for better latency
Work by Stephen Blinick.
Nightly performance runs typically consist of two levels of concurrency;
and both are fairly high.
Since the IO runs are to a ZFS filesystem, within a zpool, which is
based on some variable number of vdev's, the amount of IO driven to each
device is variable. Additionally, different device types (HDD vs SSD,
etc) can generally handle a different amount of concurrent IO before
saturating.
Nevertheless, in practice, it appears that most tests are well past the
concurrency saturation point and therefore both perform with the same
throughput, the maximum of the device. Because the queuedepth to the
device(s) is so high however, the latency is much higher than the best
possible at that throughput, and increases linearly with the increase in
concurrency.
This means that changes in code that impact latency during normal
operation (before saturation) may not be apparent when a large component
of the measured latency is from the IO sitting in a queue to be
serviced. Therefore, changing the concurrency settings is recommended
Authored by: Stephen Blinick <stephen.blinick@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Ported-by: John Wren Kennedy <jwk404@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9076
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/562
Upstream bug: DLPX-45477
Closes#7302
Due to zpool create auto-partioning in Linux (i.e. sdb1),
certain utilities need to use the parition (sdb1) while
others use the whole disk name (sdb).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#6939Closes#7261
Change file related checks to use user namespaces and make
sure involved uids/gids are mappable in the current
namespace.
Note that checks without file ownership information will
still not take user namespaces into account, as some of
these should be handled via 'zfs allow' (otherwise root in a
user namespace could issue commands such as `zpool export`).
This also adds an initial user namespace regression test
for the setgid bit loss, with a user_ns_exec helper usable
in further tests.
Additionally, configure checks for the required user
namespace related features are added for:
* ns_capable
* kuid/kgid_has_mapping()
* user_ns in cred_t
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Closes#6800Closes#7270
The test could fail when attempting to write to a newly created
volume which was missing its device node. Resolve the issue by
calling block_device_wait() which blocks until udev creates the
needed entry.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7276Closes#7277
Implement a new helper within_tolerance to test if a value
is within range of a target.
Because the dbufstats and dbufs kstat file are being read
at slightly different times, it is possible for stats to be
slightly off. Use within_tolerance to determine if the value
is "close enough" to the target.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7239Closes#7266
Some usage patterns like send/recv of replication streams can
produce a large number of events. In such a case, the current
all-syslog.sh zedlet will hold up to its name, and flood the
logs with mostly redundant information. Two mitigate this
situation, this changeset introduces to new variables
ZED_SYSLOG_SUBCLASS_INCLUDE and ZED_SYSLOG_SUBCLASS_EXCLUDE
to zed.rc that give more control over which event classes end
up in the syslog.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6886Closes#7260
Once per pass through the MMP thread's loop, the vdev tree is walked to
find a suitable leaf to write the next MMP block to. If no such leaf is
found, the thread sleeps for a while and resumes at the top of the loop.
Add an entry to multihost_history when no leaf can be found, and record
the reason in the error column. The error code for such entries is a
bitfield, displayed in hex:
0x1 At least one vdev (interior or leaf) was not writeable.
0x2 At least one writeable leaf vdev was found, but it had a pending
MMP write.
timestamp = the time in seconds since the epoch when no leaf could be
found originally.
duration = the time (in ns) during which no MMP block was written for
this reason. This does not include the preceeding inter-write period
nor the following inter-write period.
vdev_guid = the number of sequential cycles of the MMP thread looop when
this occurred.
Sample output, truncated to fit:
For records of skipped MMP writes the right-most column, vdev_path, is
reported as "-".
id txg timestamp error duration mmp_delay vdev_guid ...
936 11 1520036441 0 146264 891422313 1740883117838 ...
937 11 1520036441 0 163956 888356657 7320395061548 ...
938 11 1520036442 0 130690 885314969 7320395061548 ...
939 11 1520036442 0 2001068577 882296582 1740883117838 ...
940 11 1520036443 0 161806 882296582 7320395061548 ...
941 11 1520036443 0x2 0 998020546 1 ...
942 11 1520036444 0 136585 998020546 7320395061548 ...
943 11 1520036444 0x2 0 998020257 1 ...
944 11 1520036445 5 2002662964 994160219 1740883117838 ...
945 11 1520036445 0x2 998073118 994160219 3 ...
946 11 1520036447 0 247136 994160219 7320395061548 ...
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7212
Datasets can be busy when calling zfs destroy. Introduce
a helper function to destroy datasets and use it to destroy
datasets in zfs_allow_004_pos, zfs_promote_008_pos, and
zfs_destroy_002_pos.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7224Closes#7246Closes#7249Closes#7267
Change checksum & IO delay ratelimit thresholds from 5/sec to 20/sec.
This allows zed to actually trigger if a bunch of these events arrive in
a short period of time (zed has a threshold of 10 events in 10 sec).
Previously, if you had, say, 100 checksum errors in 1 sec, it would get
ratelimited to 5/sec which wouldn't trigger zed to fault the drive.
Also, convert the checksum and IO delay thresholds to module params for
easy testing.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7252
The test could fail because of a race condition between the files being
generated in the background and attempting to move the files. Wait for
all file generation to complete before trying to move the files around.
Also, clean up the waiting: the 'wait' command without arguments waits
for all child pids.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#7220Closes#7242Closes#7258
This change adds a test for sequential reads out of the dbuf cache.
It's essentially a copy of sequential_reads_cached, using a smaller
data set. The sequential read tests are renamed to differentiate them.
Authored by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Wren Kennedy <john.kennedy@delphix.com>
Closes#7225
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: John Eismeier <john.eismeier@gmail.com>
Closes#7237
Add new script arc_summary3.py as a complete rewrite of the
arc_summary.py tool (see issue #6873)
Add new options:
-g/--graph - Display crude graphic representation
of ARC status and quit
-r/--raw - Print all available information as
minimally formatted list (for grep)
-s/--section - Print a single section. This
replaces -p/--page, which is kept for
backwards use but marked as
depreciated
Add new sections with information on ZIL and SPL. Notify user
if sections L2ARC and VDEV are skipped instead of failing
silently. Add warning that -p/--page option is depreciated.
Developed for Python 3.5.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Scot W. Stevenson <scot.stevenson@gmail.com>
Closes#6873Closes#6892
When invoked with wrong parameters 'zfs bookmark' fails to gracefully
validate user input and crashes.
This is a regression accidentally introduced in 587e228; this commit
adds additional tests to the ZFS Test Suite to exercise this codepath.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: KireinaHoro <i@jsteward.moe>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7228Closes#7229
Prevent false positives when running the zfs_share_* test
cases due to leftover stale /var/lib/nfs/etab entries. When
starting the test group re-synchronize the /var/lib/nfs/etab
file with /etc/exports. At this point in the testing there
will be no additional `zfs share` entries to add.
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7226
* Add a zed script to kick off a scrub after a resilver. The script is
disabled by default.
* Add a optional $PATH (-P) option to zed to allow it to use a custom
$PATH for its zedlets. This is needed when you're running zed under
the ZTS in a local workspace.
* Update test scripts to not copy in all-debug.sh and all-syslog.sh by
default. They can be optionally copied in as part of zed_setup().
These scripts slow down zed considerably under heavy events loads and
can cause events to be dropped or their delivery delayed. This was
causing some sporadic failures in the 'fault' tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4662Closes#7086
This change implements 'zfs send -b' which can be used to send only
received property values whether or not they are overridden by local
settings.
This can be very useful during "restore" operations from a backup pool
because it allows to send only the property values originally sent
from the backup source, even though they were later modified on the
destination either by a 'zfs set' operation, explicit 'zfs inherit' or
overridden during the receive process via 'zfs receive -o|-x'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7156
Currently, raw zfs sends transfer the encrypted master keys and
objset_phys_t encryption parameters in the DRR_BEGIN payload of
each send file. Both of these are processed as soon as they are
read in dmu_recv_stream(), meaning that the new keys are set
before the new snapshot is received. In addition to the fact that
this changes the user's keys for the dataset earlier than they
might expect, the keys were never reset to what they originally
were in the event that the receive failed. This patch splits the
processing into objset handling and key handling, the later of
which is moved to dmu_recv_end() so that they key change can be
done atomically.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7200
Currently, the DMU relies on ZIO layer compression to free LO
dnode blocks that no longer have objects in them. However,
raw receives disable all compression, meaning that these blocks
can never be freed. In addition to the obvious space concerns,
this could also cause incremental raw receives to fail to mount
since the MAC of a hole is different from that of a completely
zeroed block.
This patch corrects this issue by adding a special case in
zio_write_compress() which will attempt to compress these blocks
to a hole even if ZIO_FLAG_RAW_ENCRYPT is set. This patch also
removes the zfs_mdcomp_disable tunable, since tuning it could
cause these same issues.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7198
A log_must call was causing count_uberblocks to return more
than just the uberblock count. Remove the log_must since it
was only logging a sleep.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7191
Project quota is a new ZFS system space/object usage accounting
and enforcement mechanism. Similar as user/group quota, project
quota is another dimension of system quota. It bases on the new
object attribute - project ID.
Project ID is a numerical value to indicate to which project an
object belongs. An object only can belong to one project though
you (the object owner or privileged user) can change the object
project ID via 'chattr -p' or 'zfs project [-s] -p' explicitly.
The object also can inherit the project ID from its parent when
created if the parent has the project inherit flag (that can be
set via 'chattr +P' or 'zfs project -s [-p]').
By accounting the spaces/objects belong to the same project, we
can know how many spaces/objects used by the project. And if we
set the upper limit then we can control the spaces/objects that
are consumed by such project. It is useful when multiple groups
and users cooperate for the same project, or a user/group needs
to participate in multiple projects.
Support the following commands and functionalities:
zfs set projectquota@project
zfs set projectobjquota@project
zfs get projectquota@project
zfs get projectobjquota@project
zfs get projectused@project
zfs get projectobjused@project
zfs projectspace
zfs allow projectquota
zfs allow projectobjquota
zfs allow projectused
zfs allow projectobjused
zfs unallow projectquota
zfs unallow projectobjquota
zfs unallow projectused
zfs unallow projectobjused
chattr +/-P
chattr -p project_id
lsattr -p
This patch also supports tree quota based on the project quota via
"zfs project" commands set as following:
zfs project [-d|-r] <file|directory ...>
zfs project -C [-k] [-r] <file|directory ...>
zfs project -c [-0] [-d|-r] [-p id] <file|directory ...>
zfs project [-p id] [-r] [-s] <file|directory ...>
For "df [-i] $DIR" command, if we set INHERIT (project ID) flag on
the $DIR, then the proejct [obj]quota and [obj]used values for the
$DIR's project ID will be shown as the total/free (avail) resource.
Keep the same behavior as EXT4/XFS does.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by Ned Bass <bass6@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
TEST_ZIMPORT_POOLS="zol-0.6.1 zol-0.6.2 master"
Change-Id: Ib4f0544602e03fb61fd46a849d7ba51a6005693c
Closes#6290
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9004
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/fafe9b241fCloses#7149
With "casesensitivity=mixed", zap_add() could fail when the number of
files/directories with the same name (varying in case) exceed the
capacity of the leaf node of a Fatzap. This results in a ASSERT()
failure as zfs_link_create() does not expect zap_add() to fail. The fix
is to handle these failures and rollback the transactions.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Closes#7011Closes#7054
zdb -ed on objset for exported pool would failed with:
failed to own dataset 'qq/fs0': No such file or directory
The reason is that zdb pass objset name to spa_import, it uses that
name to create a spa. Later, when dmu_objset_own tries to lookup the spa
using real pool name, it can't find one.
We fix this by make sure we pass pool name rather than objset name to
spa_import.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7099Closes#6464
The test used \> to detect the end of a string, but this no longer works,
so use $ which works as well since the string ends the line anyway.
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Akash Ayare <aayare@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Yuri Pankov <yuripv@icloud.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8965
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/cb1204e444Closes#7145
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
We want to be able to run channel programs outside of synching
context. This would greatly improve performance for channel programs
that just gather information, as they won't have to wait for synching
context anymore.
=== What is implemented?
This feature introduces the following:
- A new command line flag in "zfs program" to specify our intention
to run in open context. (The -n option)
- A new flag/option within the channel program ioctl which selects
the context.
- Appropriate error handling whenever we try a channel program in
open-context that contains zfs.sync* expressions.
- Documentation for the new feature in the manual pages.
=== How do we handle zfs.sync functions in open context?
When such a function is found by the interpreter and we are running
in open context we abort the script and we spit out a descriptive
runtime error. For example, given the script below ...
arg = ...
fs = arg["argv"][1]
err = zfs.sync.destroy(fs)
msg = "destroying " .. fs .. " err=" .. err
return msg
if we run it in open context, we will get back the following error:
Channel program execution failed:
[string "channel program"]:3: running functions from the zfs.sync
submodule requires passing sync=TRUE to lzc_channel_program()
(i.e. do not specify the "-n" command line argument)
stack traceback:
[C]: in function 'destroy'
[string "channel program"]:3: in main chunk
=== What about testing?
We've introduced new wrappers for all channel program tests that
run each channel program as both (startard & open-context) and
expect the appropriate behavior depending on the program using
the zfs.sync module.
OpenZFS-issue: https://www.illumos.org/issues/8677
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/17a49e15Closes#6558
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
ZFS channel programs should be able to create snapshots.
In addition to the base snapshot functionality, this entails extra
logic to handle edge cases which were formerly not possible, such as
creating then destroying a snapshot in the same transaction sync.
OpenZFS-issue: https://www.illumos.org/issues/8600
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/68089b8b
Authored by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
ZFS channel programs should be able to perform a rollback.
OpenZFS-issue: https://www.illumos.org/issues/8592
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d46b5ed6
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Don Brady <don.brady@delphix.com>
zfs.exists() in channel programs doesn't return any result, and should
have a man page entry. This patch corrects zfs.exists so that it
returns a value indicating if the dataset exists or not. It also adds
documentation about it in the man page.
OpenZFS-issue: https://www.illumos.org/issues/8605
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1e85e111
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
This change adds a make target 'testscheck' which verifies all ksh test
scripts, part of the ZFS Test Suite, have their executable bit set:
this should avoid adding new test scripts that cannot be executed by
the test-runner.py which would result in the following warning message:
Warning: Test removed from TestGroup because it failed verification.
This also verifies both *.cfg and *.kshlib files used in the ZFS Test
Suite are not executable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7131
Currently, when a raw zfs send file includes a DRR_OBJECT record
that would decrease the number of levels of an existing object,
the object is reallocated with dmu_object_reclaim() which
creates the new dnode using the old object's nlevels. For non-raw
sends this doesn't really matter, but raw sends require that
nlevels on the receive side match that of the send side so that
the checksum-of-MAC tree can be properly maintained. This patch
corrects the issue by freeing the object completely before
allocating it again in this case.
This patch also corrects several issues with dnode_hold_impl()
and related functions that prevented dnodes (particularly
multi-slot dnodes) from being reallocated properly due to
the fact that existing dnodes were not being fully cleaned up
when they were freed.
This patch adds a test to make sure that zfs recv functions
properly with incremental streams containing dnodes of different
sizes.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6821Closes#6864
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
When used in conjunction with one of '-e' or '-d' zfs receive options
none of the properties requested to be set (-o) are actually applied:
this is caused by a wrong assumption made about the toplevel dataset
in zfs_receive_one().
Fix this by correctly detecting the toplevel dataset.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7088
Introduce kstats about the dbuf hash and dbuf cache
to make it easier to inspect state. This should help
with debugging and understanding of these portions
of the codebase.
Correct format of dbuf kstat file.
Introduce a dbc column to dbufs kstat to indicate if
a dbuf is in the dbuf cache.
Introduce field filtering in the dbufstat python script.
Introduce a no header option to the dbufstat python script.
Introduce a test case to test basic mru->mfu list movement
in the ARC.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6906
When we know which devices have the pool we are looking for, sometime
it's better if we can directly pass those device paths to zpool import
instead of letting it to search through all unrelated stuff, which might
take a lot of time if you have hundreds of disks.
This patch allows option -d <dev_path> to zpool import. You can have
multiple pairs of -d <dev_path>, and zpool import will only search
through those devices. For example:
zpool import -d /dev/sda -d /dev/sdb
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7077
The intent of this patch is extend the existing deadman code
such that it's flexible enough to be used by both ztest and
on production systems. The proposed changes include:
* Added a new `zfs_deadman_failmode` module option which is
used to dynamically control the behavior of the deadman. It's
loosely modeled after, but independant from, the pool failmode
property. It can be set to wait, continue, or panic.
* wait - Wait for the "hung" I/O (default)
* continue - Attempt to recover from a "hung" I/O
* panic - Panic the system
* Added a new `zfs_deadman_ziotime_ms` module option which is
analogous to `zfs_deadman_synctime_ms` except instead of
applying to a pool TXG sync it applies to zio_wait(). A
default value of 300s is used to define a "hung" zio.
* The ztest deadman thread has been re-enabled by default,
aligned with the upstream OpenZFS code, and then extended
to terminate the process when it takes significantly longer
to complete than expected.
* The -G option was added to ztest to print the internal debug
log when a fatal error is encountered. This same option was
previously added to zdb in commit fa603f82. Update zloop.sh
to unconditionally pass -G to obtain additional debugging.
* The FM_EREPORT_ZFS_DELAY event which was previously posted
when the deadman detect a "hung" pool has been replaced by
a new dedicated FM_EREPORT_ZFS_DEADMAN event.
* The proposed recovery logic attempts to restart a "hung"
zio by calling zio_interrupt() on any outstanding leaf zios.
We may want to further restrict this to zios in either the
ZIO_STAGE_VDEV_IO_START or ZIO_STAGE_VDEV_IO_DONE stages.
Calling zio_interrupt() is expected to only be useful for
cases when an IO has been submitted to the physical device
but for some reasonable the completion callback hasn't been
called by the lower layers. This shouldn't be possible but
has been observed and may be caused by kernel/driver bugs.
* The 'zfs_deadman_synctime_ms' default value was reduced from
1000s to 600s.
* Depending on how ztest fails there may be no cache file to
move. This should not be considered fatal, collect the logs
which are available and carry on.
* Add deadman test cases for spa_deadman() and zio_wait().
* Increase default zfs_deadman_checktime_ms to 60s.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6999
Resolve new warnings reported after upgrading to shellcheck
version 0.4.6. This patch contains no functional changes.
* egrep is non-standard and deprecated. Use grep -E instead. [SC2196]
* Check exit code directly with e.g. 'if mycmd;', not indirectly
with $?. [SC2181] Suppressed.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7040
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
Occasionally observed failure of history_004_pos due to the test
case not being 100% reliable. In order to prevent false positives
disable this test case until it can be made reliable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #7026Closes#7028
When replacing a faulted device which was previously handled by a spare
multiple levels of nested interior VDEVs will be present in the pool
configuration; the following example illustrates one of the possible
situations:
NAME STATE READ WRITE CKSUM
testpool DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
spare-0 DEGRADED 0 0 0
replacing-0 DEGRADED 0 0 0
/var/tmp/fault-dev UNAVAIL 0 0 0 cannot open
/var/tmp/replace-dev ONLINE 0 0 0
/var/tmp/spare-dev1 ONLINE 0 0 0
/var/tmp/safe-dev ONLINE 0 0 0
spares
/var/tmp/spare-dev1 INUSE currently in use
This is safe and allowed, but get_replication() needs to handle this
situation gracefully to let zpool add new devices to the pool.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6678Closes#6996
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: John Kennedy <jwk404@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Prakash Surya <prakash.surya@delphix.com>
PROBLEM
=======
There's a race condition that exists if `zil_free_lwb` races with either
`zil_commit_waiter_timeout` and/or `zil_lwb_flush_vdevs_done`.
Here's an example panic due to this bug:
> ::status
debugging crash dump vmcore.0 (64-bit) from ip-10-110-205-40
operating system: 5.11 dlpx-5.2.2.0_2017-12-04-17-28-32b6ba51fb (i86pc)
image uuid: 4af0edfb-e58e-6ed8-cafc-d3e9167c7513
panic message:
BAD TRAP: type=e (#pf Page fault) rp=ffffff0010555970 addr=60 occurred in module "zfs" due to a NULL pointer dereference
dump content: kernel pages only
> $c
zio_shrink+0x12()
zil_lwb_write_issue+0x30d(ffffff03dcd15cc0, ffffff03e0730e20)
zil_commit_waiter_timeout+0xa2(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit_waiter+0xf3(ffffff03dcd15cc0, ffffff03d97ffcf8)
zil_commit+0x80(ffffff03dcd15cc0, 9a9)
zfs_write+0xc34(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
fop_write+0x5b(ffffff03dc38b140, ffffff0010555e60, 40, ffffff03e00fb758, 0)
write+0x250(42, fffffd7ff4832000, 2000)
sys_syscall+0x177()
If there's an outstanding lwb that's in `zil_commit_waiter_timeout`
waiting to timeout, waiting on it's waiter's CV, we must be sure not to
call `zil_free_lwb`. If we end up calling `zil_free_lwb`, then that LWB
may be freed and can result in a use-after-free situation where the
stale lwb pointer stored in the `zil_commit_waiter_t` structure of the
thread waiting on the waiter's CV is used.
A similar situation can occur if an lwb is issued to disk, and thus in
the `LWB_STATE_ISSUED` state, and `zil_free_lwb` is called while the
disk is servicing that lwb. In this situation, the lwb will be freed by
`zil_free_lwb`, which will result in a use-after-free situation when the
lwb's zio completes, and `zil_lwb_flush_vdevs_done` is called.
This race condition is prevented in `zil_close` by calling `zil_commit`
before `zil_free_lwb` is called, which will ensure all outstanding (i.e.
all lwb's in the `LWB_STATE_OPEN` and/or `LWB_STATE_ISSUED` states)
reach the `LWB_STATE_DONE` state before the lwb's are freed
(`zil_commit` will not return untill all the lwb's are
`LWB_STATE_DONE`).
Further, this race condition is prevented in `zil_sync` by only calling
`zil_free_lwb` for lwb's that do not have their `lwb_buf` pointer set.
All lwb's not in the `LWB_STATE_DONE` state will have a non-null value
for this pointer; the pointer is only cleared in
`zil_lwb_flush_vdevs_done`, at which point the lwb's state will be
changed to `LWB_STATE_DONE`.
This race *is* present in `zil_suspend`, leading to this bug.
At first glance, it would appear as though this would not be true
because `zil_suspend` will call `zil_commit`, just like `zil_close`, but
the problem is that `zil_suspend` will set the zilog's `zl_suspend`
field prior to calling `zil_commit`. Further, in `zil_commit`, if
`zl_suspend` is set, `zil_commit` will take a special branch of logic
and use `txg_wait_synced` instead of performing the normal `zil_commit`
logic.
This call to `txg_wait_synced` might be good enough for the data to
reach disk safely before it returns, but it does not ensure that all
outstanding lwb's reach the `LWB_STATE_DONE` state before it returns.
This is because, if there's an lwb "stuck" in
`zil_commit_waiter_timeout`, waiting for it's lwb to timeout, it will
maintain a non-null value for it's `lwb_buf` field and thus `zil_sync`
will not free that lwb. Thus, even though the lwb's data is already on
disk, the lwb will be left lingering, waiting on the CV, and will
eventually timeout and be issued to disk even though the write is
unnecessary.
So, after `zil_commit` is called from `zil_suspend`, we incorrectly
assume that there are not outstanding lwb's, and proceed to free all
lwb's found on the zilog's lwb list. As a result, we free the lwb that
will later be used `zil_commit_waiter_timeout`.
SOLUTION
========
The solution to this, is to ensure all outstanding lwb's complete before
calling `zil_free_lwb` via `zil_destroy` in `zil_suspend`. This patch
accomplishes this goal by forcing the normal `zil_commit` logic when
called from `zil_sync`.
Now, `zil_suspend` will call `zil_commit_impl` which will always use the
normal logic of waiting/issuing lwb's to disk before it returns. As a
result, any lwb's outstanding when `zil_commit_impl` is called will be
guaranteed to reach the `LWB_STATE_DONE` state by the time it returns.
Further, no new lwb's will be created via `zil_commit` since the zilog's
`zl_suspend` flag will be set. This will force all new callers of
`zil_commit` to use `txg_wait_synced` instead of creating and issuing
new lwb's.
Thus, all lwb's left on the zilog's lwb list when `zil_destroy` is
called will be in the `LWB_STATE_DONE` state, and we'll avoid this race
condition.
OpenZFS-issue: https://www.illumos.org/issues/8909
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/ece62b6f8dCloses#6940
When sequential scrubs were merged, all calls to arc_read()
(including prefetch IOs) were given ZIO_PRIORITY_ASYNC_READ.
Unfortunately, this behaves badly with an existing issue where
prefetch IOs cannot be re-prioritized after the issue. The
result is that synchronous reads end up in the same vdev_queue
as the scrub IOs and can have (in some workloads) multiple
seconds of latency.
This patch incorporates 2 changes. The first ensures that all
scrub IOs are given ZIO_PRIORITY_SCRUB to allow the vdev_queue
code to differentiate between these I/Os and user prefetches.
Second, this patch introduces zio_change_priority() to provide
the missing capability to upgrade a zio's priority.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6921Closes#6926
Using a command similar to 'arc_summary.py | head' causes
a broken pipe exception. Gracefully exit in the case of a
broken pipe in arc_summary.py.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6965Closes#6969
If an invalid option is provided to arc_summary.py we handle any error
thrown from the getopt Python module and print the usage help message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6983
The function that fills the uberblock ring buffer on every device label
has been reworked to avoid occasional failures caused by a race
condition that prevents 'zpool sync' from writing some uberblock
sequentially: this happens when the pool sync ioctl dispatch code calls
txg_wait_synced() while we're already waiting for a TXG to sync.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6924Closes#6977
When the multihost property is enabled it should be impossible to
import an active pool even using the force (-f) option. This patch
prevents a forced import from succeeding when importing with a
stale cache file.
The root cause of the problem is that the kernel modules trusted
the hostid provided in configuration. This is always correct when
the configuration is generated by scanning for the pool. However,
when using an existing cache file the hostid could be stale which
would result in the activity check being skipped.
Resolve the issue by always using the hostid read from the label
configuration where the best uberblock was found.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6933Closes#6971
* Teach ZED to handle spares usingi the configured ashift: if the zpool
'ashift' property is set then ZED should use its value when kicking
in a hotspare; with this change 512e disks can be used as spares
for VDEVs that were created with ashift=9, even if ZFS natively
detects them as 4K block devices.
* Introduce an additional auto_spare test case which verifies that in
the face of multiple device failures an appropiate number of spares
are kicked in.
* Fix zed_stop() in "libtest.shlib" which did not correctly wait the
target pid.
* Fix ZED crashing on startup caused by a race condition in libzfs
when used in multi-threaded context.
* Convert ZED over to using the tpool library which is already present
in the Illumos FMA code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2562Closes#6858
Occasionally observed failure of vdev_zaps_004_pos due to the test
case not being 100% reliable. In order to prevent false positives
disable this test case until it can be made reliable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6935Closes#6936
Occasionally observed failure of create-o_ashift due to the test
case not being 100% reliable. In order to prevent false positives
disable this test case until it can be made reliable.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6924Closes#6925
When the pool configuration contains a hole due to a previous device
removal ignore this top level vdev. Failure to do so will result in
the current configuration being assessed to have a non-uniform
replication level and the expected warning will be disabled.
The zpool_add_010_pos test case was extended to cover this scenario.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6907Closes#6911
Fix a regression accidentally introduced in 1b81ab4 that prevents
'zfs get {user|group}objused@' from correctly reporting the requested
value.
Update "userspace_003_pos.ksh" and "groupspace_003_pos.ksh" to verify
this functionality.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6908
Currently, scrubs and resilvers can take an extremely
long time to complete. This is largely due to the fact
that zfs scans process pools in logical order, as
determined by each block's bookmark. This makes sense
from a simplicity perspective, but blocks in zfs are
often scattered randomly across disks, particularly
due to zfs's copy-on-write mechanisms.
This patch improves performance by splitting scrubs
and resilvers into a metadata scanning phase and an IO
issuing phase. The metadata scan reads through the
structure of the pool and gathers an in-memory queue
of I/Os, sorted by size and offset on disk. The issuing
phase will then issue the scrub I/Os as sequentially as
possible, greatly improving performance.
This patch also updates and cleans up some of the scan
code which has not been updated in several years.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Authored-by: Alek Pinchuk <apinchuk@datto.com>
Authored-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#3625Closes#6256
Occasionally observed failure of zvol_ENOSPC_001_pos due to the
test case taking too long to complete. Disable the test case until
it can be improved.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #5848Closes#6862
On Linux, ftruncate(2) always changes the file timestamps, even if the
file size is not changed. However, in case of a successfull
truncate(2), the timestamps are updated only if the file size changes.
This translates to the VFS calling the ZFS Posix Layer "setattr"
function (zpl_setattr) with ATTR_MTIME and ATTR_CTIME unconditionally
set on the iattr mask only when doing a ftruncate(2), while the
truncate(2) is left to the filesystem implementation to be dealt with.
This behaviour is consistent with POSIX:2004/SUSv3 specifications
where there's no explicit requirement for file size changes to update
the timestamps only for ftruncate(2):
http://pubs.opengroup.org/onlinepubs/009695399/functions/truncate.htmlhttp://pubs.opengroup.org/onlinepubs/009695399/functions/ftruncate.html
This has been later updated in POSIX:2008/SUSv4 where, for both
truncate(2)/ftruncate(2), there's no mention of this size change
requirement:
http://austingroupbugs.net/view.php?id=489http://pubs.opengroup.org/onlinepubs/9699919799/functions/truncate.htmlhttp://pubs.opengroup.org/onlinepubs/9699919799/functions/ftruncate.html
Unfortunately the Linux VFS is still calling into the ZPL without
ATTR_MTIME/ATTR_CTIME set in the truncate(2) case: we fix this by
explicitly updating the timestamps when detecting the ATTR_SIZE bit,
which is always set in do_truncate(), on the iattr mask.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6811Closes#6819
When dumping objects larger than 128PiB it's possible for do_dump() to
miscalculate the FREE_RECORD offset due to an integer overflow
condition: this prevents the receiving end from correctly restoring
the dumped object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6760
Additionally add four new tests:
* zpool_events_clear: verify 'zpool events -c' functionality
* zpool_events_cliargs: verify command line options and arguments
* zpool_events_follow: verify 'zpool events -f'
* zpool_events_poolname: verify events filtering by pool name
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3285Closes#6762
Added -n flag to zpool reopen that allows a running scrub
operation to continue if there is a device with Dirty Time Log.
By default if a component device has a DTL and zpool reopen
is executed all running scan operations will be restarted.
Added functional tests for `zpool reopen`
Tests covers following scenarios:
* `zpool reopen` without arguments,
* `zpool reopen` with pool name as argument,
* `zpool reopen` while scrubbing,
* `zpool reopen -n` while scrubbing,
* `zpool reopen -n` while resilvering,
* `zpool reopen` with bad arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Closes#6076Closes#6746
The ZED is expected to automatically kick in a hot spare device
when there's one available in the pool and a sufficient number of
read errors have been encountered. Use zinject to simulate the
failure condition and verify the hot spare is used.
auto_spare_001_pos.ksh: read IO errors, the vdev is FAULTED
auto_spare_002_pos.ksh: read CHECKSUM errors, the vdev is DEGRADE
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6280
History commands and events were being suppressed for the
'zpool create' command since the history object did not
yet exist. Create the object earlier so this history
doesn't get lost.
Split the pool_destroy event in to pool_destroy and
pool_export so they may be distinguished.
Updated events_001_pos and events_002_pos test cases. They
now check for the expected history events and were reworked
to be more reliable.
Reviewed-by: Nathaniel Clark <nathaniel.l.clark@intel.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6712Closes#6486
The only place vn_rename and vn_remove are used is when writing
out an updated pool configuration file. By truncating the file
instead of renaming and removing it we can avoid having to implement
these interfaces entirely. Functionally an empty cache file is
treated the same as a missing cache file. This is particularly
advantageous because the Linux kernel has never provided a way
to reliably implement vn_rename and vn_remove.
The cachefile_004_pos.ksh test case was updated to understand
that an empty cache file is the same as a missing one.
The zfs-import-* systemd service files were not updated to use
ConditionFileNotEmpty in place of ConditionPathExists. This
means that after exporting all pools and rebooting new pools
will not the scanned for on the next boot. This small change
should not impact normal usage since pools are not exported
as part of a normal shutdown.
Documentation was updated accordingly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Arkadiusz Bubała <arkadiusz.bubala@open-e.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes zfsonlinux/spl#648
Closes#6753
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
The chattr cleanup step may fail to delete the user if there is still
an active process running as that user. Retry the userdel when this
occurs to eliminate spurious false positves.
ERROR: userdel quser1 exited 8
userdel: user quser1 is currently used by process 26814
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6749
Because resuming from a token requires "guid" -> "snapshot" mapping
we have to walk the whole dataset hierarchy to find the right snapshot
to send; when both source and destination exists, for an incremental
resumable stream, libzfs gets confused and picks up the wrong snapshot
to send from: this results in attempting to send
"destination@snap1 -> source@snap2"
instead of
"source@snap1 -> source@snap2"
which fails with a "Invalid cross-device link" error (EXDEV).
Fix this by adjusting the logic behind dataset traversal in
zfs_iter_children() to pick the right snapshot to send from.
Additionally update dry-run 'zfs send -t' to print its output to
stderr: this is consistent with other dry-run commands.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6618Closes#6619Closes#6623
With the addition of the ABD changes consumption of the virtual
address space has been greatly reduced. This exposed an issue on
CONFIG_HIGHMEM systems where free memory was being calculated
incorrectly. Functionally this didn't cause any major problems
prior to ABD because a lack of available virtual address space
was used as an indicator of low memory.
This patch makes the following changes to address the issue and
in the process realigns the code further with OpenZFS. There
are no substantive changes in behavior for 64-bit systems.
* Added CONFIG_HIGHMEM case to the arc_all_memory() and
arc_free_memory() functions to only consider low memory pages
on CONFIG_HIGHMEM systems.
* The arc_free_memory() function was updated to return bytes
instead of pages to be consistent with the other helper
functions. In user space we make up some reasonable values
since currently only testing is performed in this context.
* Adds three new values to the arcstats kstat to provide visibility
in to the ARC's assessment of the memory situation:
memory_all_bytes, memory_free_bytes, and memory_available_bytes.
* Added kmem_reap() call to arc_available_memory() for 32-bit
builds to realign code with OpenZFS.
* Reduced size of test file in /async_destroy_001_pos.ksh to
speed up test case. Multiple txgs are still required.
* Move vdevs used by zpool_clear_001_pos and zpool_upgrade_002_pos
to TEST_BASE_DIR location to speed up test cases.
Reviewed-by: David Quigley <david.quigley@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5352Closes#6734
When receiving a FREEOBJECTS record, receive_freeobjects()
incorrectly skips a freed object in some cases. Specifically, this
happens when the first object in the range to be freed doesn't exist,
but the second object does. This leaves an object allocated on disk
on the receiving side which is unallocated on the sending side, which
may cause receiving subsequent incremental streams to fail.
The bug was caused by an incorrect increment of the object index
variable when current object being freed doesn't exist. The
increment is incorrect because incrementing the object index is
handled by a call to dmu_object_next() in the increment portion of
the for loop statement.
Add test case that exposes this bug.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6694Closes#6695
This change adds four new tests to the ZTS:
* zfs_diff_changes: verify type of changes diplayed (-, +, R and M)
* zfs_diff_cliargs: verify command line options and arguments
* zfs_diff_timestamp: verify 'zfs diff -t'
* zfs_diff_types: verify type of objects (files, dirs, pipes...)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Wren Kennedy <john.kennedy@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6686
Quote "$MMP_IMPORT_MSG" when it is passed as an argument, as it is a
multi-word string. Some tests were passing when they should not have,
because the grep was only testing for the first word.
Correct the message expected when no hostid is set and the test attempts
to enable multihost. It did not match the actual output in that
situation.
Disable ztest_reguid() when ztest is invoked with the -M option. If
ztest performs a reguid, a concurrent import attempt may fail with the
error "one or more devices is currently unavailable" if the guid sum is
calculated on the original device guids but compared against the guid
sum ztest wrote based on the new device guids.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6666
The slog_replay_volume.ksh test case will fail when the pool is
layered on files in a filesystem which does not support discard.
Avoid this issue by creating the pool using DISKS which will
either be loopback device or real disk.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6654
Fix spurious events_002_pos failures by waiting longer before
grabbing the log to check for the resilver_finish event. It
would be better to rework this logic to wait only as long as
needed rather than a fixed timeout.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6651
* Add configure option to enable gcov analysis.
* Includes a few minor ctime fixes.
* Add codecov.yml configuration.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6642
Changing any metadata, should modify the ctime.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: gaurkuma <gauravk.18@gmail.com>
Closes#3644Closes#6586
Running distclean removes the following files because of an error
in Makefile.am
deleted: tests/zfs-tests/include/commands.cfg
deleted: tests/zfs-tests/include/libtest.shlib
deleted: tests/zfs-tests/include/math.shlib
deleted: tests/zfs-tests/include/properties.shlib
deleted: tests/zfs-tests/include/zpool_script.shlib
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: David Quigley <david.quigley@intel.com>
Closes#6636
This change allow (ref)reservation to be set larger than the current
ZVOL size: this is safe as we normally set refreservation > volsize
at ZVOL creation time when we account for metadata.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#2468Closes#6610
This leverages the functionality introduced in cf7684b to expose
verbose, dry-run and parsable 'zfs send' options for bookmarks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3666Closes#6601
The portion of the zvol_replay_write() handler responsible for
replaying indirect log records for some reason never existed.
As a result indirect log records were not being correctly replayed.
This went largely unnoticed since the majority of zvol log records
were of the type WR_COPIED or WR_NEED_COPY prior to OpenZFS 7578.
This patch updates zvol_replay_write() to correctly handle these
log records and adds a new test case which verifies volume replay
to prevent any regression. The existing test case which verified
replay on filesystem was renamed slog_replay_fs.ksh for clarity.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6603Closes#6615
This reverts commit 65dcb0f67a until
a comprehensive fix is finalized. The stricter interior dnode
detection in 4c5b89f59e and the new
test case added by this patch revealed a issue with resizing
dnodes when receiving an incremental backup stream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #6576
Refactor dmu_object_alloc_dnsize() and dnode_hold_impl() to simplify the
code, fix errors introduced by commit dbeb879 (PR #6117) interacting
badly with large dnodes, and improve performance.
* When allocating a new dnode in dmu_object_alloc_dnsize(), update the
percpu object ID for the core's metadnode chunk immediately. This
eliminates most lock contention when taking the hold and creating the
dnode.
* Correct detection of the chunk boundary to work properly with large
dnodes.
* Separate the dmu_hold_impl() code for the FREE case from the code for
the ALLOCATED case to make it easier to read.
* Fully populate the dnode handle array immediately after reading a
block of the metadnode from disk. Subsequently the dnode handle array
provides enough information to determine which dnode slots are in use
and which are free.
* Add several kstats to allow the behavior of the code to be examined.
* Verify dnode packing in large_dnode_008_pos.ksh. Since the test is
purely creates, it should leave very few holes in the metadnode.
* Add test large_dnode_009_pos.ksh, which performs concurrent creates
and deletes, to complement existing test which does only creates.
With the above fixes, there is very little contention in a test of about
200,000 racing dnode allocations produced by tests 'large_dnode_008_pos'
and 'large_dnode_009_pos'.
name type data
dnode_hold_dbuf_hold 4 0
dnode_hold_dbuf_read 4 0
dnode_hold_alloc_hits 4 3804690
dnode_hold_alloc_misses 4 216
dnode_hold_alloc_interior 4 3
dnode_hold_alloc_lock_retry 4 0
dnode_hold_alloc_lock_misses 4 0
dnode_hold_alloc_type_none 4 0
dnode_hold_free_hits 4 203105
dnode_hold_free_misses 4 4
dnode_hold_free_lock_misses 4 0
dnode_hold_free_lock_retry 4 0
dnode_hold_free_overflow 4 0
dnode_hold_free_refcount 4 57
dnode_hold_free_txg 4 0
dnode_allocate 4 203154
dnode_reallocate 4 0
dnode_buf_evict 4 23918
dnode_alloc_next_chunk 4 4887
dnode_alloc_race 4 0
dnode_alloc_next_block 4 18
The performance is slightly improved for concurrent creates with
16+ threads, and unchanged for low thread counts.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#5396Closes#6522Closes#6414Closes#6564
When receiving an incremental backup stream, call
dmu_object_reclaim_dnsize() if an object's dnode size differs between
the incremental source and target. Otherwise it may appear that a
dnode which has shrunk is still occupying slots which are in fact
free. This will cause a failure to receive new objects that should
occupy the now-free slots.
Add a test case to verify that an incremental stream containing
objects with changed dnode sizes can be received without error. This
test case fails without this change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#6366Closes#6576
Since OpenZFS 7578 (1b7c1e5) if we have a ZVOL with logbias=throughput
we will force WR_INDIRECT itxs in zvol_log_write() setting itx->itx_lr
offset and length to the offset and length of the BIO from
zvol_write()->zvol_log_write(): these offset and length are later used
to take a range lock in zillog->zl_get_data function: zvol_get_data().
Now suppose we have a ZVOL with blocksize=8K and push 4K writes to
offset 0: we will only be range-locking 0-4096. This means the
ASSERTion we make in dbuf_unoverride() is no longer valid because now
dmu_sync() is called from zilog's get_data functions holding a partial
lock on the dbuf.
Fix this by taking a range lock on the whole block in zvol_get_data().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6238Closes#6315Closes#6356Closes#6477
It's not enough to preserve/restore MS_RDONLY on the superblock flags
to avoid remounting a snapshot read-write: be explicit about our
intentions to the VFS layer so the readonly bit is updated correctly
in do_remount_sb().
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6510Closes#6515
* Removed zpios kmod, utility, headers and man page.
* Removed unused scripts zpios-profile/*, zpios-test/*,
zpool-config/*, smb.sh, zpios-sanity.sh, zpios-survey.sh,
zpios.sh, and zpool-create.sh.
* Removed zfs-script-config.sh.in. When building 'make' generates
a common.sh with in-tree path information from the common.sh.in
template. This file and sourced by the test scripts and used
for in-tree testing, it is not included in the packages. When
building packages 'make install' uses the same template to
create a new common.sh which is appropriate for the packaging.
* Removed unused functions/variables from scripts/common.sh.in.
Only minimal path information and configuration environment
variables remain.
* Removed unused scripts from scripts/ directory.
* Remaining shell scripts in the scripts directory updated to
cleanly pass shellcheck and added to checked scripts.
* Renamed tests/test-runner/cmd/ to tests/test-runner/bin/ to
match install location name.
* Removed last traces of the --enable-debug-dmu-tx configure
options which was retired some time ago.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6509
The addition of the large_dnode_008_pos test case, which runs
right before this one, exposed some racy behavior in grow_pool
setup.sh on the Ubuntu kmemleak builder. Before creating
partitions on a device destroying any existing ones.
ERROR: set_partition 1 100mb loop0 exited 1
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6499Closes#6516
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
The test case frequently hangs on buildbot
TEST builders. Disable it for now.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6487
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
When performing concurrent object allocations using the new
multi-threaded allocator and large dnodes it's possible to
allocate overlapping large dnodes.
This case should have been handled by detecting an error
returned by dnode_hold_impl(). But that logic only checked
the returned dnp was not-NULL, and the dnp variable was not
reset to NULL when retrying. Resolve this issue by properly
checking the return value of dnode_hold_impl().
Additionally, it was possible that dnode_hold_impl() would
misreport a dnode as free when it was in fact in use. This
could occurs for two reasons:
* The per-slot zrl_lock must be held over the entire critical
section which includes the alloc/free until the new dnode
is assigned to children_dnodes. Additionally, all of the
zrl_lock's in the range must be held to protect moving
dnodes.
* The dn->dn_ot_type cannot be solely relied upon to check
the type. When allocating a new dnode its type will be
DMU_OT_NONE after dnode_create(). Only latter when
dnode_allocate() is called will it transition to the new
type. This means there's a window when allocating where
it can mistaken for a free dnode.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6414Closes#6439
rsend tests in the test suite frequently create and
destroy datasets. It is possible for zfs destroy to
return an error code indicating the dataset is busy.
Simply use a log_must_busy in these cases to retry
destroying those datasets. Other fixes to rsend test
cases to avoid unmounting and remounting filesystems
and some cleanup.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6418
Use kstat to get a more accurate count of uberblock updates.
Using a loop with zdb can potentially miss some uberblocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6407Closes#6419
At import time spa_import() calls zvol_create_minors() directly: with
the current implementation we have no way to avoid device node
creation when volmode=none.
Fix this by enforcing volmode=none directly in zvol_alloc().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6426
Test case zfs_send_007_pos regularly is killed
by test-runner during zfs-tests on buildbot. Disable
it for now until further investigation can be done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6422
If we are in the middle of an incremental 'zfs receive', the child
.../%recv will exist. If we run 'zfs promote' .../%recv, it will "work",
but then zfs gets confused about the status of the new dataset.
Attempting to do this promote should be an error.
Similarly renaming .../%recv datasets should not be allowed.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#4843Closes#6339
There is no need to perform the activity check before detecting that the
user must set the system hostid, because the pool's multihost property
is on, but spa_get_hostid() returned 0. The initial call to
vdev_uberblock_load() provided the information required.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6388
Add a callback to wake all running mmp threads when
zfs_multihost_interval is changed.
This is necessary when the interval is changed from a very large value
to a significantly lower one, while pools are imported that have the
multihost property enabled.
Without this commit, the mmp thread does not wake up and detect the new
interval until after it has waited the old multihost interval time. A
user monitoring mmp writes via the provided kstat would be led to
believe that the changed setting did not work.
Added a test in the ZTS under mmp to verify the new functionality is
working.
Added a test to ztest which starts and stops mmp threads, and calls into
the code to signal sleeping mmp threads, to test for deadlocks or
similar locking issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6387
Brian Behlendorf
DeHackEd
Alek P
Stephen Blinick
Paul Zuchowski
Wolfgang Bumiller
Giuseppe Di Natale
Tony Hutter
Olaf Faaland
chrisrd
John Wren Kennedy
John Eismeier
Scot W. Stevenson
LOLi
Tom Caputi
Nasf-Fan
John Wren Kennedy
sanjeevbagewadi
Chunwei Chen
Serapheim Dimitropoulos
Don Brady
Chris Williamson
Brad Lewis
Chunwei Chen
Prakash Surya
Arkadiusz Bubała
David Quigley
Ned Bass
Gaurav Kumar