The cache of struct svc_export and struct svc_expkey by nfsd and
rpc.mountd for the snapshot holds references to the mount point.
We need to flush them out before unmounting, otherwise umount
would fail with EBUSY.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#6000Closes#10783
In absence of inheriting entry for owner@, group@, or everyone@,
zfs_acl_chmod() is called to set these. This can cause confusion for Samba
admins who do not expect these entries to appear on newly created files and
directories once they have been stripped from from the parent directory.
When aclmode is set to "restricted", chmod is prevented on non-trivial ACLs.
It is not a stretch to assume that in this case the administrator does not want
ZFS to add the missing special entries. Add check for this aclmode, and if an
inherited entry is present skip zfs_acl_chmod().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#10748
Many modern devices use physical allocation units that are much
larger than the minimum logical allocation size accessible by
external commands. Two prevalent examples of this are 512e disk
drives (512b logical sector, 4K physical sector) and flash devices
(512b logical sector, 4K or larger allocation block size, and 128k
or larger erase block size). Operations that modify less than the
physical sector size result in a costly read-modify-write or garbage
collection sequence on these devices.
Simply exporting the true physical sector of the device to ZFS would
yield optimal performance, but has two serious drawbacks:
1. Existing pools created with devices that have different logical
and physical block sizes, but were configured to use the logical
block size (e.g. because the OS version used for pool construction
reported the logical block size instead of the physical block
size) will suddenly find that the vdev allocation size has
increased. This can be easily tolerated for active members of
the array, but ZFS would prevent replacement of a vdev with
another identical device because it now appears that the smaller
allocation size required by the pool is not supported by the new
device.
2. The device's physical block size may be too large to be supported
by ZFS. The optimal allocation size for the vdev may be quite
large. For example, a RAID controller may export a vdev that
requires read-modify-write cycles unless accessed using 64k
aligned/sized requests. ZFS currently has an 8k minimum block
size limit.
Reporting both the logical and physical allocation sizes for vdevs
solves these problems. A device may be used so long as the logical
block size is compatible with the configuration. By comparing the
logical and physical block sizes, new configurations can be optimized
and administrators can be notified of any existing pools that are
sub-optimal.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Macy <mmacy@freebsd.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10619
We limit the size of nvlists passed to the kernel so a user cannot make
the kernel do an unreasonably large allocation. On FreeBSD this limit
was 128 kiB, which turns out to be a bit too small when doing some
operations involving a large number of datasets or snapshots, for
example replication.
Make this limit tunable, with a platform-specific auto default.
Linux keeps its limit at KMALLOC_MAX_SIZE. FreeBSD uses 1/4 of the
system limit on user wired memory, which allows it to scale depending
on system configuration.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Issue #6572Closes#10706
The ARC caches data in scatter ABD's, which are collections of pages,
which are typically 4K. Therefore, the space used to cache each block
is rounded up to a multiple of 4K. The ABD subsystem tracks this wasted
memory in the `scatter_chunk_waste` kstat. However, the ARC's `size` is
not aware of the memory used by this round-up, it only accounts for the
size that it requested from the ABD subsystem.
Therefore, the ARC is effectively using more memory than it is aware of,
due to the `scatter_chunk_waste`. This impacts observability, e.g.
`arcstat` will show that the ARC is using less memory than it
effectively is. It also impacts how the ARC responds to memory
pressure. As the amount of `scatter_chunk_waste` changes, it appears to
the ARC as memory pressure, so it needs to resize `arc_c`.
If the sector size (`1<<ashift`) is the same as the page size (or
larger), there won't be any waste. If the (compressed) block size is
relatively large compared to the page size, the amount of
`scatter_chunk_waste` will be small, so the problematic effects are
minimal.
However, if using 512B sectors (`ashift=9`), and the (compressed) block
size is small (e.g. `compression=on` with the default `volblocksize=8k`
or a decreased `recordsize`), the amount of `scatter_chunk_waste` can be
very large. On a production system, with `arc_size` at a constant 50%
of memory, `scatter_chunk_waste` has been been observed to be 10-30% of
memory.
This commit adds `scatter_chunk_waste` to `arc_size`, and adds a new
`waste` field to `arcstat`. As a result, the ARC's memory usage is more
observable, and `arc_c` does not need to be adjusted as frequently.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10701
`KMC_KMEM` and `KMC_VMEM` are now unused since all SPL-implemented
caches are `KMC_KVMEM`.
KMC_KMEM: Given the default value of `spl_kmem_cache_kmem_limit`, we
don't use kmalloc to back the SPL caches, instead we use kvmalloc
(KMC_KVMEM). The flag, module parameter, /proc entries, and associated
code are removed.
KMC_VMEM: This flag is not used, and kvmalloc() is always preferable to
vmalloc(). The flag, /proc entries, and associated code are removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10673
Linux and FreeBSD will most likely never see this issue.
On macOS when kext is unloaded, but zed is still connected, zed
will be issued ENODEV. As the cdevsw is released, the kernel
will not have zfsdev_release() called to release minor/onexit/events,
and it "leaks". This ensures it is cleaned up before unload.
Changed the for loop from zsprev, to zsnext style, for less
code duplication.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10700
The make_request_fn and associated API was replaced recently in a
Linux 5.9 merge, to replace its functionality with a new submit_bio
member in struct block_device_operations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#10696
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
The ARC shrinker callback `arc_shrinker_count/_scan()` is invoked by the
kernel's shrinker mechanism when the system is running low on free
pages. This happens via 2 code paths:
1. "direct reclaim": The system is attempting to allocate a page, but we
are low on memory. The ARC shrinker callback is invoked from the
page-allocation code path.
2. "indirect reclaim": kswapd notices that there aren't many free pages,
so it invokes the ARC shrinker callback.
In both cases, the kernel's shrinker code requests that the ARC shrinker
callback release some of its cache, and then it measures how many pages
were released. However, it's measurement of released pages does not
include pages that are freed via `__free_pages()`, which is how the ARC
releases memory (via `abd_free_chunks()`). Rather, the kernel shrinker
code is looking for pages to be placed on the lists of reclaimable pages
(which is separate from actually-free pages).
Because the kernel shrinker code doesn't detect that the ARC has
released pages, it may call the ARC shrinker callback many times,
resulting in the ARC "collapsing" down to `arc_c_min`. This has several
negative impacts:
1. ZFS doesn't use RAM to cache data effectively.
2. In the direct reclaim case, a single page allocation may wait a long
time (e.g. more than a minute) while we evict the entire ARC.
3. Even with the improvements made in 67c0f0dedc ("ARC shrinking blocks
reads/writes"), occasionally `arc_size` may stay above `arc_c` for the
entire time of the ARC collapse, thus blocking ZFS read/write operations
in `arc_get_data_impl()`.
To address these issues, this commit limits the ways that the ARC
shrinker callback can be used by the kernel shrinker code, and mitigates
the impact of arc_is_overflowing() on ZFS read/write operations.
With this commit:
1. We limit the amount of data that can be reclaimed from the ARC via
the "direct reclaim" shrinker. This limits the amount of time it takes
to allocate a single page.
2. We do not allow the ARC to shrink via kswapd (indirect reclaim).
Instead we rely on `arc_evict_zthr` to monitor free memory and reduce
the ARC target size to keep sufficient free memory in the system. Note
that we can't simply rely on limiting the amount that we reclaim at once
(as for the direct reclaim case), because kswapd's "boosted" logic can
invoke the callback an unlimited number of times (see
`balance_pgdat()`).
3. When `arc_is_overflowing()` and we want to allocate memory,
`arc_get_data_impl()` will wait only for a multiple of the requested
amount of data to be evicted, rather than waiting for the ARC to no
longer be overflowing. This allows ZFS reads/writes to make progress
even while the ARC is overflowing, while also ensuring that the eviction
thread makes progress towards reducing the total amount of memory used
by the ARC.
4. The amount of memory that the ARC always tries to keep free for the
rest of the system, `arc_sys_free` is increased.
5. Now that the shrinker callback is able to provide feedback to the
kernel's shrinker code about our progress, we can safely enable
the kswapd hook. This will allow the arc to receive notifications
when memory pressure is first detected by the kernel. We also
re-enable the appropriate kstats to track these callbacks.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10600
Renamed to avoid conflicting with refcount.h when a different
implementation is already provided by the platform.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10620
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10623
By default, `spl_kmem_cache_expire` is `KMC_EXPIRE_MEM`, meaning that
objects will be removed from kmem cache magazines by
`spl_kmem_cache_reap_now()`.
There is also a module parameter to change this to `KMC_EXPIRE_AGE`,
which establishes a maximum lifetime for objects to stay in the
magazine. This setting has rarely, if ever, been used, and is not
regularly tested.
This commit removes the code for `KMC_EXPIRE_AGE`, and associated module
parameters.
Additionally, the unused module parameter
`spl_kmem_cache_obj_per_slab_min` is removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10608
The process of evicting data from the ARC is referred to as
`arc_adjust`.
This commit changes the term to `arc_evict`, which is more specific.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10592
The SPL kmem_cache implementation provides a mechanism, `skc_reclaim`,
whereby individual caches can register a callback to be invoked when
there is memory pressure. This mechanism is used in only one place: the
ARC registers the `hdr_recl()` reclaim function. This function wakes up
the `arc_reap_zthr`, whose job is to call `kmem_cache_reap()` and
`arc_reduce_target_size()`.
The `skc_reclaim` callbacks are invoked only by shrinker callbacks and
`arc_reap_zthr`, and only callback only wakes up `arc_reap_zthr`. When
called from `arc_reap_zthr`, waking `arc_reap_zthr` is a no-op. When
called from shrinker callbacks, we are already aware of memory pressure
and responding to it. Therefore there is little benefit to ever calling
the `hdr_recl()` `skc_reclaim` callback.
The `arc_reap_zthr` also wakes once a second, and if memory is low when
allocating an ARC buffer. Therefore, additionally waking it from the
shrinker calbacks has little benefit.
The shrinker callbacks can be invoked very frequently, e.g. 10,000 times
per second. Additionally, for invocation of the shrinker callback,
skc_reclaim is invoked many times. Therefore, this mechanism consumes
significant amounts of CPU time.
The kmem_cache shrinker calls `spl_kmem_cache_reap_now()`, which,
in addition to invoking `skc_reclaim()`, does two things to attempt to
free pages for use by the system:
1. Return free objects from the magazine layer to the slab layer
2. Return entirely-free slabs to the page layer (i.e. free pages)
These actions apply only to caches implemented by the SPL, not those
that use the underlying kernel SLAB/SLUB caches. The SPL caches are
used for objects >=32KB, which are primarily linear ABD's cached in the
DBUF cache.
These actions (freeing objects from the magazine layer and returning
entirely-free slabs) are also taken whenever a `kmem_cache_free()` call
finds a full magazine. So there would typically be zero entirely-free
slabs, and the number of objects in magazines is limited (typically no
more than 64 objects per magazine, and there's one magazine per CPU).
Therefore the benefit of `spl_kmem_cache_reap_now()`, while nonzero, is
modest.
We also call `spl_kmem_cache_reap_now()` from the `arc_reap_zthr`, when
memory pressure is detected. Therefore, calling
`spl_kmem_cache_reap_now()` from the kmem_cache shrinker is not needed.
This commit removes the `skc_reclaim` mechanism, its only callback
`hdr_recl()`, and the kmem_cache shrinker callback.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10576
Stock kernels older than 4.10 do not export the has_capability()
function which is required by commit e59a377. To avoid breaking
the build on older kernels revert to the safe legacy behavior and
return EACCES when privileges cannot be checked.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10565Closes#10573
`arc_free_memory()` returns the amount of memory that the ARC considers
to be free. This includes pages that are not actually free, but can be
evicted with essentially zero cost (without doing any i/o), for example
the page cache. The ARC can "squeeze out" any pages included in this
calculation, leaving only `arc_sys_free` (1/64th of RAM) for these
free/evictable pages.
Included in the count of free/evictable pages is
`nr_inactive_anon_pages()`, which is described as "Anonymous memory that
has not been used recently and can be swapped out". These pages would
have to be written out to disk (swap) in order to evict them, and they
are not included in `/proc/meminfo`'s `MemAvailable`.
Therefore it is not appropriate for `nr_inactive_anon_pages()` to be
included in the free/evictable memory returned by `arc_free_memory()`,
because the ARC shouldn't (intentionally) make the system swap.
This commit removes `nr_inactive_anon_pages()` from the memory returned
by `arc_free_memory()`. This is a step towards enabling the ARC to
manage free memory by monitoring it and reducing the ARC size as we
notice that there is insufficient free memory (in the `arc_reap_zthr`),
rather than the current method of relying on the `arc_shrinker`
callback.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10575
Move/add include of <linux/percpu_compat.h> to satisfy missing
requirements.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain@dolbeau.org>
Closes#10568Closes#10569
The filesystem_limit and snapshot_limit properties limit the number of
filesystems or snapshots that can be created below this dataset.
According to the manpage, "The limit is not enforced if the user is
allowed to change the limit." Two types of users are allowed to change
the limit:
1. Those that have been delegated the `filesystem_limit` or
`snapshot_limit` permission, e.g. with
`zfs allow USER filesystem_limit DATASET`. This works properly.
2. A user with elevated system privileges (e.g. root). This does not
work - the root user will incorrectly get an error when trying to create
a snapshot/filesystem, if it exceeds the `_limit` property.
The problem is that `priv_policy_ns()` does not work if the `cred_t` is
not that of the current process. This happens when
`dsl_enforce_ds_ss_limits()` is called in syncing context (as part of a
sync task's check func) to determine the permissions of the
corresponding user process.
This commit fixes the issue by passing the `task_struct` (typedef'ed as
a `proc_t`) to syncing context, and then using `has_capability()` to
determine if that process is privileged. Note that we still need to
pass the `cred_t` to syncing context so that we can check if the user
was delegated this permission with `zfs allow`.
This problem only impacts Linux. Wrappers are added to FreeBSD but it
continues to use `priv_check_cred()`, which works on arbitrary `cred_t`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8226Closes#10545
OS-specific code (e.g. under `module/os/linux`) does not need to share
its code structure with any other operating systems. In particular, the
ARC and kmem code need not be similar to the code in illumos, because we
won't be syncing this OS-specific code between operating systems. For
example, if/when illumos support is added to the common repo, we would
add a file `module/os/illumos/zfs/arc_os.c` for the illumos versions of
this code.
Therefore, we can simplify the code in the OS-specific ARC and kmem
routines.
These changes do not impact system behavior, they are purely code
cleanup. The changes are:
Arenas are not used on Linux or FreeBSD (they are always `NULL`), so
`heap_arena`, `zio_arena`, and `zio_alloc_arena` can be removed, along
with code that uses them.
In `arc_available_memory()`:
* `desfree` is unused, remove it
* rename `freemem` to avoid conflict with pre-existing `#define`
* remove checks related to arenas
* use units of bytes, rather than converting from bytes to pages and
then back to bytes
`SPL_KMEM_CACHE_REAP` is unused, remove it.
`skc_reap` is unused, remove it.
The `count` argument to `spl_kmem_cache_reap_now()` is unused, remove
it.
`vmem_size()` and associated type and macros are unused, remove them.
In `arc_memory_throttle()`, use a less confusing variable name to store
the result of `arc_free_memory()`.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10499
The SPL provides a wrapper for the kernel's shrinker callbacks, which
enables the ZFS code to interface with multiple versions of the shrinker
API's from different kernel versions. Specifically, Linux kernels 3.0 -
3.11 has a single "combined" callback, and Linux kernels 3.12 and later
have two "split" callbacks. The SPL provides a wrapper function so that
the ZFS code only needs to implement one version of the callbacks.
Currently the SPL's wrappers are designed such that the ZFS code
implements the older, "combined" callback. There are a few downsides to
this approach:
* The general design within ZFS is for the latest Linux kernel to be
considered the "first class" API.
* The newer, "split" callback API is easier to understand, because each
callback has one purpose.
* The current wrappers do not completely abstract out the differing
API's, so ZFS code needs `#ifdef` code to handle the differing return
values required for different kernel versions.
This commit addresses these drawbacks by having the ZFS code provide the
latest, "split" callbacks, and the SPL provides a wrapping function for
the older, "combined" API.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10502
A previous commit enabled the tracking of object allocations
in Linux-backed caches from the SPL layer for debuggability.
The commit is: 9a170fc6fe
Unfortunately, it also introduced minor performance regressions
that were highlighted by the ZFS perf test-suite. Within Delphix
we found that the regression would be from -1%, all the way up
to -8% for some workloads.
This commit brings performance back up to par by creating a
separate counter for those caches and making it a percpu in
order to avoid lock-contention.
The initial performance testing was done by myself, and the
final round was conducted by @tonynguien who was also the one
that discovered the regression and highlighted the culprit.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#10397
ZFS registers a memory hook, `__arc_shrinker_func`, which is supposed to
allow the ARC to shrink when the kernel experiences memory pressure.
The ARC shrinker changes `arc_c` via a call to
`arc_reduce_target_size()`. Before commit 3ec34e5527, the ARC
shrinker would also evict data from the ARC to bring `arc_size` down to
the new `arc_c`. However, that commit (seemingly inadvertently) made it
so that the ARC shrinker no longer evicts any data or waits for eviction
to complete.
Repeated calls to the ARC shrinker can reduce `arc_c` drastically, often
all the way to `arc_c_min`. Since it doesn't wait for the actual
eviction of data from the ARC, this creates a situation where `arc_size`
is more than `arc_c` for the several seconds/minutes it takes for
`arc_adjust_zthr` to evict data from the ARC. During this time,
arc_get_data_impl() will block, so ZFS can't process read/write requests
(e.g. from iSCSI, NFS, or read/write syscalls).
To ensure that `arc_c` doesn't shrink faster than the adjust thread can
keep up, this commit makes the ARC shrinker wait for the eviction to
complete, resulting in similar behavior to what we had before commit
3ec34e5527.
Note: commit 3ec34e5527 is `OpenZFS 9284 - arc_reclaim_thread
has 2 jobs` and was integrated in December 2018, and is part of ZoL
0.8.x but not 0.7.x.
Additionally, when the ARC size is reduced drastically, the
`arc_adjust_zthr` can be on-CPU for many seconds without blocking. Any
threads that are bound to the same CPU that arc_adjust_zthr is running
on will not able to run for a long time.
To ensure that CPU-bound threads can make progress, this commit changes
`arc_evict_state_impl()` make a voluntary preemption call,
`cond_resched()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-70703
Closes#10496
This tunable required a handler to be implemented for
ZFS_MODULE_PARAM_CALL.
Add the handler so the tunable can be declared in common code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10490
spl-generic.c defines some of the libgcc integer library functions on
32-bit. Don't bother checking -Wmissing-prototypes since nothing should
directly call these functions from C code.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Include the header with prototypes in the file that provides definitions
as well, to catch any mismatch between prototype and definition.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Implement semi-compatible functionality for mode=0 (preallocation)
and mode=FALLOC_FL_KEEP_SIZE (preallocation beyond EOF) for ZPL.
Since ZFS does COW and snapshots, preallocating blocks for a file
cannot guarantee that writes to the file will not run out of space.
Even if the first overwrite was guaranteed, it would not handle any
later overwrite of blocks due to COW, so strict compliance is futile.
Instead, make a best-effort check that at least enough free space is
currently available in the pool (with a bit of margin), then create
a sparse file of the requested size and continue on with life.
This does not handle all cases (e.g. several fallocate() calls before
writing into the files when the filesystem is nearly full), which
would require a more complex mechanism to be implemented, probably
based on a modified version of dmu_prealloc(), but is usable as-is.
A new module option zfs_fallocate_reserve_percent is used to control
the reserve margin for any single fallocate call. By default, this
is 110% of the requested preallocation size, so an additional 10% of
available space is reserved for overhead to allow the application a
good chance of finishing the write when the fallocate() succeeds.
If the heuristics of this basic fallocate implementation are not
desirable, the old non-functional behavior of returning EOPNOTSUPP
for calls can be restored by setting zfs_fallocate_reserve_percent=0.
The parameter of zfs_statvfs() is changed to take an inode instead
of a dentry, since no dentry is available in zfs_fallocate_common().
A few tests from @behlendorf cover basic fallocate functionality.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Arshad Hussain <arshad.super@gmail.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Issue #326Closes#10408
On Illumos callers of cv_timedwait and cv_timedwait_hires
can't distinguish between whether or not the cv was signaled
or the call timed out. Illumos handles this (for some definition
of handles) by calling cv_signal in the return path if we were
signaled but the return value indicates instead that we timed
out. This would make sense if it were possible to query the the
cv for its net signal disposition. However, this isn't possible
and, in spite of the fact that there are places in the code that
clearly take a different and incompatible path if a timeout value
is indicated, this distinction appears to be rather subtle to most
developers. This problem is further compounded by the fact that on
Linux, calling cv_signal in the return path wouldn't even do the
right thing unless there are other waiters.
Since it is possible for the caller to independently determine how
much time is remaining but it is not possible to query if the cv
was in fact signaled, prioritizing signalling over timeout seems
like a cleaner solution. In addition, judging from usage patterns
within the code itself, it is also less error prone.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10471
Apparently missed in the initial port integration was
the need to reap the abd_chunk_cache on FreeBSD. This
change addresses that oversight.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10474
Linux defines different vdev_disk_t members to macOS, but they are
only used in vdev_disk.c so move the declaration there.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10452
For MIPS architectures on Linux the ZERO_PAGE macro references
empty_zero_page, which is exported as a GPL symbol. The call to
ZERO_PAGE in abd_alloc_zero_scatter has been removed and a single
zero'd page is now allocated for each of the pages in abd_zero_scatter
in the kernel ABD code path.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10428
The linux module can be built either as an external module, or compiled
into the kernel, using copy-builtin. The source and build directories
are slightly different between the two cases, and currently, compiling
into the kernel still refers to some files from the configured ZFS
source tree, instead of the copies inside the kernel source tree. There
is also duplication between copy-builtin, which creates a Kbuild file to
build ZFS inside the kernel tree, and the top-level module/Makefile.in.
Fix this by moving the list of modules and the CFLAGS settings into a
new module/Kbuild.in, which will be used by the kernel kbuild
infrastructure, and using KBUILD_EXTMOD to distinguish the two cases
within the Makefiles, in order to choose appropriate include
directories etc.
Module CFLAGS setting is simplified by using subdir-ccflags-y (available
since 2.6.30) to set them in the top-level Kbuild instead of each
individual module. The disabling of -Wunused-but-set-variable is removed
from the lua and zfs modules. The variable that the Makefile uses is
actually not defined, so this has no effect; and the warning has long
been disabled by the kernel Makefile itself.
The target_cpu definition in module/{zfs,zcommon} is removed as it was
replaced by use of CONFIG_SPARC64 in
commit 70835c5b75 ("Unify target_cpu handling")
os/linux/{spl,zfs} are removed from obj-m, as they are not modules in
themselves, but are included by the Makefile in the spl and zfs module
directories. The vestigial Makefiles in os and os/linux are removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10379Closes#10421
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
The l2arc_evict() function is responsible for evicting buffers which
reference the next bytes of the L2ARC device to be overwritten. Teach
this function to additionally TRIM that vdev space before it is
overwritten if the device has been filled with data. This is done by
vdev_trim_simple() which trims by issuing a new type of TRIM,
TRIM_TYPE_SIMPLE.
We also implement a "Trim Ahead" feature. It is a zfs module parameter,
expressed in % of the current write size. This trims ahead of the
current write size. A minimum of 64MB will be trimmed. The default is 0
which disables TRIM on L2ARC as it can put significant stress to
underlying storage devices. To enable TRIM on L2ARC we set
l2arc_trim_ahead > 0.
We also implement TRIM of the whole cache device upon addition to a
pool, pool creation or when the header of the device is invalid upon
importing a pool or onlining a cache device. This is dependent on
l2arc_trim_ahead > 0. TRIM of the whole device is done with
TRIM_TYPE_MANUAL so that its status can be monitored by zpool status -t.
We save the TRIM state for the whole device and the time of completion
on-disk in the header, and restore these upon L2ARC rebuild so that
zpool status -t can correctly report them. Whole device TRIM is done
asynchronously so that the user can export of the pool or remove the
cache device while it is trimming (ie if it is too slow).
We do not TRIM the whole device if persistent L2ARC has been disabled by
l2arc_rebuild_enabled = 0 because we may not want to lose all cached
buffers (eg we may want to import the pool with
l2arc_rebuild_enabled = 0 only once because of memory pressure). If
persistent L2ARC has been disabled by setting the module parameter
l2arc_rebuild_blocks_min_l2size to a value greater than the size of the
cache device then the whole device is trimmed upon creation or import of
a pool if l2arc_trim_ahead > 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam D. Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9713Closes#9789Closes#10224
Move the GFP flags kernel compat code from c file to kmem header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#10424
The `pgprot` argument has been removed from `__vmalloc` in Linux 5.8,
being `PAGE_KERNEL` always now [1].
Detect this during configure and define a wrapper for older kernels.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/mm/vmalloc.c?h=next-20200605&id=88dca4ca5a93d2c09e5bbc6a62fbfc3af83c4fca
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#10422
In Illumos it is possible to call ioctl functions from within the
kernel by passing the FKIOCTL flag. Neither FreeBSD nor Linux support
that, but it doesn't hurt to keep it around, as all the code is there.
Before this commit it was a dead code and zc_iflags was always zero.
Restore this functionality by allowing to pass a flag to the
zfsdev_ioctl_common() function.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#10417
The strcpy() and sprintf() functions are deprecated on some platforms.
Care is needed to ensure correct size is used. If some platforms
miss snprintf, we can add a #define to sprintf, likewise strlcpy().
The biggest change is adding a size parameter to zfs_id_to_fuidstr().
The various *_impl_get() functions are only used on linux and have
not yet been updated.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10400
C++ is a little picky about not using keywords for names, or string
constness.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10409
Expand the FreeBSD spl for kstats to support all current types
Move the dataset_kstats_t back to zvol_state_t from zfs_state_os_t
now that it is common once again
```
kstat.zfs/mypool.dataset.objset-0x10b.nunlinked: 0
kstat.zfs/mypool.dataset.objset-0x10b.nunlinks: 0
kstat.zfs/mypool.dataset.objset-0x10b.nread: 150528
kstat.zfs/mypool.dataset.objset-0x10b.reads: 48
kstat.zfs/mypool.dataset.objset-0x10b.nwritten: 134217728
kstat.zfs/mypool.dataset.objset-0x10b.writes: 1024
kstat.zfs/mypool.dataset.objset-0x10b.dataset_name: mypool/datasetname
```
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#10386
Adding the gang ABD type, which allows for linear and scatter ABDs to
be chained together into a single ABD.
This can be used to avoid doing memory copies to/from ABDs. An example
of this can be found in vdev_queue.c in the vdev_queue_aggregate()
function.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian <bwa@clemson.edu>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10069
Commit fc551d7 introduced the wrappers abd_enter_critical() and
abd_exit_critical() to mark critical sections. On Linux these are
implemented with the local_irq_save() and local_irq_restore() macros
which set the 'flags' argument when saving. By wrapping them with
a function the local variable is no longer set by the macro and is
no longer properly restored.
Convert abd_enter_critical() and abd_exit_critical() to macros to
resolve this issue and ensure the flags are properly restored.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10332
Reorganizing ABD code base so OS-independent ABD code has been placed
into a common abd.c file. OS-dependent ABD code has been left in each
OS's ABD source files, and these source files have been renamed to
abd_os.
The OS-independent ABD code is now under:
module/zfs/abd.c
With the OS-dependent code in:
module/os/linux/zfs/abd_os.c
module/os/freebsd/zfs/abd_os.c
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10293
reflect delete permissions for ACLs
Authored by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
Porting Notes:
* Only comments are updated
OpenZFS-issue: https://www.illumos.org/issues/6765
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/da412744bcCloses#10266
- and some additional considerations
Authored by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/6762
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1eb4e906ecCloses#10266
with aclmode=passthrough
Authored by: Albert Lee <trisk@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/6764
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/de0f1ddb59Closes#10266
Authored-by: Paul B. Henson <henson@acm.org>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/3254
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/71dbfc287cCloses#10266
Porting notes:
* Updated zfs_acl_chmod to take 'boolean_t isdir' as first parameter
rather than 'zfsvfs_t *zfsvfs'
* zfs man pages changes mixed between zfs and new zfsprops man pages
Reviewed by: Aram Hvrneanu <aram@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Robert Gordon <rbg@openrbg.com>
Reviewed by: Mark.Maybee@oracle.com
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@nexenta.com>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/742
OpenZFS-issue: https://www.illumos.org/issues/664
OpenZFS-issue: https://www.illumos.org/issues/279
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a3c49ce110Closes#10266
We can improve the performance of writes to zvols by using
dmu_tx_hold_write_by_dnode() instead of dmu_tx_hold_write(). This
reduces lock contention on the first block of the dnode object, and also
reduces the amount of CPU needed. The benefit will be highest with
multi-threaded async writes (i.e. writes that don't call zil_commit()).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10184
This commit makes the L2ARC persistent across reboots. We implement
a light-weight persistent L2ARC metadata structure that allows L2ARC
contents to be recovered after a reboot. This significantly eases the
impact a reboot has on read performance on systems with large caches.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Saso Kiselkov <skiselkov@gmail.com>
Co-authored-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Ported-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#925Closes#1823Closes#2672Closes#3744Closes#9582
Set arc_c_min before arc_c_max so that when zfs_arc_min is set lower
than the default allmem/32 zfs_arc_max can also be set lower.
Add warning messages when tunables are being ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10157Closes#10158
Commit https://github.com/torvalds/linux/commit/3d745ea5 simplified
the blk_alloc_queue() interface by updating it to take the request
queue as an argument. Add a wrapper function which accepts the new
arguments and internally uses the available interfaces.
Other minor changes include increasing the Linux-Maximum to 5.6 now
that 5.6 has been released. It was not bumped to 5.7 because this
release has not yet been finalized and is still subject to change.
Added local 'struct zvol_state_os *zso' variable to zvol_alloc.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10181Closes#10187
Add a mechanism to wait for delete queue to drain.
When doing redacted send/recv, many workflows involve deleting files
that contain sensitive data. Because of the way zfs handles file
deletions, snapshots taken quickly after a rm operation can sometimes
still contain the file in question, especially if the file is very
large. This can result in issues for redacted send/recv users who
expect the deleted files to be redacted in the send streams, and not
appear in their clones.
This change duplicates much of the zpool wait related logic into a
zfs wait command, which can be used to wait until the internal
deleteq has been drained. Additional wait activities may be added
in the future.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9707
In zfs_write(), the loop continues to the next iteration without
accounting for partial copies occurring in uiomove_iov when
copy_from_user/__copy_from_user_inatomic return a non-zero status.
This results in "zfs: accessing past end of object..." in the
kernel log, and the write failing.
Account for partial copies and update uio struct before returning
EFAULT, leave a comment explaining the reason why this is done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: ilbsmart <wgqimut@gmail.com>
Signed-off-by: Fabio Scaccabarozzi <fsvm88@gmail.com>
Closes#8673Closes#10148
== Summary ==
Prior to this change, sync writes to a zvol are processed serially.
This commit makes zvols process concurrently outstanding sync writes in
parallel, similar to how reads and async writes are already handled.
The result is that the throughput of sync writes is tripled.
== Background ==
When a write comes in for a zvol (e.g. over iscsi), it is processed by
calling `zvol_request()` to initiate the operation. ZFS is expected to
later call `BIO_END_IO()` when the operation completes (possibly from a
different thread). There are a limited number of threads that are
available to call `zvol_request()` - one one per iscsi client (unless
using MC/S). Therefore, to ensure good performance, the latency of
`zvol_request()` is important, so that many i/o operations to the zvol
can be processed concurrently. In other words, if the client has
multiple outstanding requests to the zvol, the zvol should have multiple
outstanding requests to the storage hardware (i.e. issue multiple
concurrent `zio_t`'s).
For reads, and async writes (i.e. writes which can be acknowledged
before the data reaches stable storage), `zvol_request()` achieves low
latency by dispatching the bulk of the work (including waiting for i/o
to disk) to a taskq. The taskq callback (`zvol_read()` or
`zvol_write()`) blocks while waiting for the i/o to disk to complete.
The `zvol_taskq` has 32 threads (by default), so we can have up to 32
concurrent i/os to disk in service of requests to zvols.
However, for sync writes (i.e. writes which must be persisted to stable
storage before they can be acknowledged, by calling `zil_commit()`),
`zvol_request()` does not use `zvol_taskq`. Instead it blocks while
waiting for the ZIL write to disk to complete. This has the effect of
serializing sync writes to each zvol. In other words, each zvol will
only process one sync write at a time, waiting for it to be written to
the ZIL before accepting the next request.
The same issue applies to FLUSH operations, for which `zvol_request()`
calls `zil_commit()` directly.
== Description of change ==
This commit changes `zvol_request()` to use
`taskq_dispatch_ent(zvol_taskq)` for sync writes, and FLUSh operations.
Therefore we can have up to 32 threads (the taskq threads)
simultaneously calling `zil_commit()`, for a theoretical performance
improvement of up to 32x.
To avoid the locking issue described in the comment (which this commit
removes), we acquire the rangelock from the taskq callback (e.g.
`zvol_write()`) rather than from `zvol_request()`. This applies to all
writes (sync and async), reads, and discard operations. This means that
multiple simultaneously-outstanding i/o's which access the same block
can complete in any order. This was previously thought to be incorrect,
but a review of the block device interface requirements revealed that
this is fine - the order is inherently not defined. The shorter hold
time of the rangelock should also have a slight performance improvement.
For an additional slight performance improvement, we use
`taskq_dispatch_ent()` instead of `taskq_dispatch()`, which avoids a
`kmem_alloc()` and eliminates a failure mode. This applies to all
writes (sync and async), reads, and discard operations.
== Performance results ==
We used a zvol as an iscsi target (server) for a Windows initiator
(client), with a single connection (the default - i.e. not MC/S).
We used `diskspd` to generate a workload with 4 threads, doing 1MB
writes to random offsets in the zvol. Without this change we get
231MB/s, and with the change we get 728MB/s, which is 3.15x the original
performance.
We ran a real-world workload, restoring a MSSQL database, and saw
throughput 2.5x the original.
We saw more modest performance wins (typically 1.5x-2x) when using MC/S
with 4 connections, and with different number of client threads (1, 8,
32).
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10163
Linux changed the default max ARC size to 1/2 of physical memory to
deal with shortcomings of the Linux SLUB allocator. Other platforms
do not require the same logic.
Implement an arc_default_max() function to determine a default max ARC
size in platform code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10155
If a has rollback has occurred while a file is open and unlinked.
Then when the file is closed post rollback it will not exist in the
rolled back version of the unlinked object. Therefore, the call to
zap_remove_int() may correctly return ENOENT and should be allowed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6812Closes#9739
The normal lock order is that the dp_config_rwlock must be held before
the ds_opening_lock. For example, dmu_objset_hold() does this.
However, dmu_objset_open_impl() is called with the ds_opening_lock held,
and if the dp_config_rwlock is not already held, it will attempt to
acquire it. This may lead to deadlock, since the lock order is
reversed.
Looking at all the callers of dmu_objset_open_impl() (which is
principally the callers of dmu_objset_from_ds()), almost all callers
already have the dp_config_rwlock. However, there are a few places in
the send and receive code paths that do not. For example:
dsl_crypto_populate_key_nvlist, send_cb, dmu_recv_stream,
receive_write_byref, redact_traverse_thread.
This commit resolves the problem by requiring all callers ot
dmu_objset_from_ds() to hold the dp_config_rwlock. In most cases, the
code has been restructured such that we call dmu_objset_from_ds()
earlier on in the send and receive processes, when we already have the
dp_config_rwlock, and save the objset_t until we need it in the middle
of the send or receive (similar to what we already do with the
dsl_dataset_t). Thus we do not need to acquire the dp_config_rwlock in
many new places.
I also cleaned up code in dmu_redact_snap() and send_traverse_thread().
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9662Closes#10115
__zio_execute() calls zio_taskq_member() to determine if we are running
in a zio interrupt taskq, in which case we may need to switch to
processing this zio in a zio issue taskq. The call to
zio_taskq_member() can become a performance bottleneck when we are
processing a high rate of zio's.
zio_taskq_member() calls taskq_member() on each of the zio interrupt
taskqs, of which there are 21. This is slow because each call to
taskq_member() does tsd_get(taskq_tsd), which on Linux is relatively
slow.
This commit improves the performance of zio_taskq_member() by having it
cache the value of tsd_get(taskq_tsd), reducing the number of those
calls to 1/21th of the current behavior.
In a test case running `zfs send -c >/dev/null` of a filesystem with
small blocks (average 2.5KB/block), zio_taskq_member() was using 6.7% of
one CPU, and with this change it is reduced to 1.3%. Overall time to
perform the `zfs send` reduced by 10% (~150,000 block/sec to ~165,000
blocks/sec).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10070
This function should only return "linux" on Linux.
Move the kernel part of the function out of common code.
Fix the tests for FreeBSD.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10079
By adding a zfs_file_private accessor to the common
interfaces and some extensions to FreeBSD platform
code it is now possible to share the implementations
for the aforementioned functions.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10073
Commit https://github.com/torvalds/linux/commit/9e8d42a0f accidentally
converted the static inline function blkg_tryget() to GPL-only for
kernels built with CONFIG_PREEMPT_RCU=y and CONFIG_BLK_CGROUP=y.
Resolve the build issue by providing our own equivalent functionality
when needed which uses rcu_read_lock_sched() internally as before.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9745Closes#10072
As part of the Linux kernel's y2038 changes the time_t type has been
fully retired. Callers are now required to use the time64_t type.
Rather than move to the new type, I've removed the few remaining
places where a time_t is used in the kernel code. They've been
replaced with a uint64_t which is already how ZFS internally
handled these values.
Going forward we should work towards updating the remaining user
space time_t consumers to the 64-bit interfaces.
Reviewed-by: Matthew Macy <mmacy@freebsd.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10052Closes#10064
* Add dedicated donde_set_dirtyctx routine.
* Add empty dirty record on destroy assertion.
* Make much more extensive use of the SET_ERROR macro.
Reviewed-by: Will Andrews <wca@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9924
The `convoff` function is called only in one code path in `zfs_space`.
Each caller of `zfs_space` is called with a `flock64_t` that has
`l_whence` set to `SEEK_SET`. This means that `convoff` always results
in a no-op as the `bfp` parameter has `l_whence` set to `SEEK_SET` and
`int whence` is `SEEK_SET` as well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Dirkjan Bussink <d.bussink@gmail.com>
Closes#10006
Unlinked files don't respect synchronous flush commands, but when they get relinked
their state is unknown. Previously we force flushed all such files even when
sync=disabled. Correct this case.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#10005
When growing the size of a (VMEM or KVMEM) kmem cache, spl_cache_grow()
always does taskq_dispatch(spl_cache_grow_work), and then waits for the
KMC_BIT_GROWING to be cleared by the taskq thread.
The taskq thread (spl_cache_grow_work()) does:
1. allocate new slab and add to list
2. wake_up_all(skc_waitq)
3. clear_bit(KMC_BIT_GROWING)
Therefore, the waiting thread can wake up before GROWING has been
cleared. It will see that the growing has not yet completed, and go
back to sleep until it hits the 100ms timeout.
This can have an extreme performance impact on workloads that alloc/free
more than fits in the (statically-sized) magazines. These workloads
allocate and free slabs with high frequency.
The problem can be observed with `funclatency spl_cache_grow`, which on
some workloads shows that 99.5% of the time it takes <64us to allocate
slabs, but we spend ~70% of our time in outliers, waiting for the 100ms
timeout.
The fix is to do `clear_bit(KMC_BIT_GROWING)` before
`wake_up_all(skc_waitq)`.
A future investigation should evaluate if we still actually need to
taskq_dispatch() at all, and if so on which kernel versions.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9989
We need to do the same thing to update all spas on any OS for these
tunables, so let's share the code.
While here let's match the types of the literals initializing the
variables with the type of the variable.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9964
The timestamp_truncate() function was added, it replaces the existing
timespec64_trunc() function. This change renames our wrapper function
to be consistent with the upstream name and updates the compatibility
code for older kernels accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9956Closes#9961
The proc_ops structure was introduced to replace the use of of the
file_operations structure when registering proc handlers. This
change creates a new kstat_proc_op_t typedef for compatibility
which can be used to pass around the correct structure.
This change additionally adds the 'const' keyword to all of the
existing proc operations structures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9961
This solves the issue of loading the spl module on RISC-V.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9942
It violated sequence described in kstat.h, and at least on FreeBSD
kstat_install() uses provided names to create the sysctls. If the
names are not available at the time, it ends up bad.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#9933
When we finish a zfs receive, dmu_recv_end_sync() calls
zvol_create_minors(async=TRUE). This kicks off some other threads that
create the minor device nodes (in /dev/zvol/poolname/...). These async
threads call zvol_prefetch_minors_impl() and zvol_create_minor(), which
both call dmu_objset_own(), which puts a "long hold" on the dataset.
Since the zvol minor node creation is asynchronous, this can happen
after the `ZFS_IOC_RECV[_NEW]` ioctl and `zfs receive` process have
completed.
After the first receive ioctl has completed, userland may attempt to do
another receive into the same dataset (e.g. the next incremental
stream). This second receive and the asynchronous minor node creation
can interfere with one another in several different ways, because they
both require exclusive access to the dataset:
1. When the second receive is finishing up, dmu_recv_end_check() does
dsl_dataset_handoff_check(), which can fail with EBUSY if the async
minor node creation already has a "long hold" on this dataset. This
causes the 2nd receive to fail.
2. The async udev rule can fail if zvol_id and/or systemd-udevd try to
open the device while the the second receive's async attempt at minor
node creation owns the dataset (via zvol_prefetch_minors_impl). This
causes the minor node (/dev/zd*) to exist, but the udev-generated
/dev/zvol/... to not exist.
3. The async minor node creation can silently fail with EBUSY if the
first receive's zvol_create_minor() trys to own the dataset while the
second receive's zvol_prefetch_minors_impl already owns the dataset.
To address these problems, this change synchronously creates the minor
node. To avoid the lock ordering problems that the asynchrony was
introduced to fix (see #3681), we create the minor nodes from open
context, with no locks held, rather than from syncing contex as was
originally done.
Implementation notes:
We generally do not need to traverse children or prefetch anything (e.g.
when running the recv, snapshot, create, or clone subcommands of zfs).
We only need recursion when importing/opening a pool and when loading
encryption keys. The existing recursive, asynchronous, prefetching code
is preserved for use in these cases.
Channel programs may need to create zvol minor nodes, when creating a
snapshot of a zvol with the snapdev property set. We figure out what
snapshots are created when running the LUA program in syncing context.
In this case we need to remember what snapshots were created, and then
try to create their minor nodes from open context, after the LUA code
has completed.
There are additional zvol use cases that asynchronously own the dataset,
which can cause similar problems. E.g. changing the volmode or snapdev
properties. These are less problematic because they are not recursive
and don't touch datasets that are not involved in the operation, there
is still potential for interference with subsequent operations. In the
future, these cases should be similarly converted to create the zvol
minor node synchronously from open context.
The async tasks of removing and renaming minors do not own the objset,
so they do not have this problem. However, it may make sense to also
convert these operations to happen synchronously from open context, in
the future.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-65948
Closes#7863Closes#9885
With recent SPL changes there is no longer any need for a per
platform version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9860
Over the years several slightly different approaches were used
in the Makefiles to determine the target architecture. This
change updates both the build system and Makefile to handle
this in a consistent fashion.
TARGET_CPU is set to i386, x86_64, powerpc, aarch6 or sparc64
and made available in the Makefiles to be used as appropriate.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9848
On kernels with KASAN enabled the following failure can be observed as
soon as the zfs module is loaded:
VERIFY(IS_P2ALIGNED(ptr, PAGE_SIZE)) failed
PANIC at spl-kmem-cache.c:228:kv_alloc()
The problem is kmalloc() has never guaranteed aligned allocations; this
requirement resulted in zfsonlinux/spl@8b45dda which removed all
kmalloc() usage in kv_alloc().
Until a GFP_ALIGNED flag (or equivalent functionality) is provided by
the kernel this commit partially reverts 66955885 and 6d948c35 to
prevent k(v)malloc() allocations in kv_alloc().
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9813
Update the project website links contained in to repository to
reference the secure https://zfsonlinux.org address.
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9837
When qat_compress() fails to allocate the required contiguous memory
it mistakenly returns success. This prevents the fallback software
compression from taking over and (un)compressing the block.
Resolve the issue by correctly setting the local 'status' variable
on all exit paths. Furthermore, initialize it to CPA_STATUS_FAIL
to ensure qat_compress() always fails safe to guard against any
similar bugs in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9784Closes#9788
As of cppcheck 1.82 surpress the warning regarding shifting too many
bits for __divdi3() implemention. The algorithm used here is correct.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
As of cppcheck 1.82 warnings are issued when using the list_for_each_*
functions with an uninitialized variable. Functionally, this is fine
but to resolve the warning initialize these variables.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9732
Apply umask to `mode` which will eventually be applied to inode.
This is needed since VFS doesn't apply umask for O_TMPFILE files.
(Note that zpl_init_acl() applies `ip->i_mode &= ~current_umask();`
only when POSIX ACL is used.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8997Closes#8998
FreeBSD's vfs currently doesn't permit file systems
to do their own locking. To avoid having to have
duplicate zfs functions with and without locking add
locking here. With luck these changes can be removed
in the future.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9715
The quota functions are common to all implementations and can be
moved to common code. As a simplification they were moved to the
Linux platform code in the initial refactoring.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9710
Change many of the znops routines to take a znode rather
than an inode so that zfs_replay code can be largely shared
and in the future the much of the znops code may be shared.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9708
The zfsvfs->z_sb field is Linux specified and should be abstracted.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9697
Update the vdev_disk_open() retry logic to use a specified number
of milliseconds to be more robust. Additionally, on failure log
both the time waited and requested timeout to the internal log.
The default maximum allowed open retry time has been increased
from 500ms to 1000ms.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9680
Update zfs_deadman_failmode to use the ZFS_MODULE_PARAM_CALL
wrapper, and split the common and platform specific portions.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9670
Remove the ASSERTV macro and handle suppressing unused
compiler warnings for variables only in ASSERTs using the
__attribute__((unused)) compiler annotation. The annotation
is understood by both gcc and clang.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9671
FreeBSD needs to cope with multiple version of the zfs_cmd_t
structure. Allowing the platform code to pre and post
process the cmd structure makes it possible to work with
legacy tooling.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9624
fallocate(2) is a Linux-specific system call which in unavailable
on other platforms.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9633
FreeBSD needs to be able to pass the jail id to the jail/unjail ioctls
and the struct file in the device structure is unused.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9625
youzhongyang
Andrew
Ryan Moeller
Ryan Moeller
Matthew Ahrens
Jorgen Lundman
Coleman Kane
Matthew Ahrens
Matthew Macy
Matthew Macy
Brian Behlendorf
Romain Dolbeau
Serapheim Dimitropoulos
Arvind Sankar
adilger
Brian Atkinson
George Amanakis
Michael Niewöhner
Pawel Jakub Dawidek
Allan Jude
Allan Jude
Brian Atkinson
Paul B. Henson
Paul Dagnelie
Fabio Scaccabarozzi
Dirkjan Bussink
DeHackEd
Romain Dolbeau
Alexander Motin
loli10K
Ubuntu
Tomohiro Kusumi