Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
It was changed in e99932f7de,
but without docs update.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#14400
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
This change turns `MZAP_MAX_BLKSZ` into a `ZFS_MODULE_PARAM()` called
`zap_micro_max_size`. As a result, we can experiment with different
micro ZAP sizes to improve directory size scaling.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Co-authored-by: Toomas Soome <toomas.soome@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateuszpiotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14292
Recent ARC commits added new statistic counters, such as iohits,
uncached state, etc. Represent those. Also some of previously
reported numbers were confusing or even made no sense. Cleanup
and restructure existing reports.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Issue #14115
Issue #14123
Issue #14243Closes#14320
This saves 40 bytes per full ARC header, reducing it on FreeBSD from
240 to 200 bytes on production bits.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14315
This adds support to color zfs diff (in the style of git diff)
conditional on the ZFS_COLOR environment variable.
Signed-off-by: Ethan Coe-Renner <coerenner1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14179
Correct new mandoc errors.
```
STYLE: input text line longer than 80 bytes
STYLE: no blank before trailing delimiter
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14148
As new compression algorithms are added to ZFS, it could be useful for
people to recompress data with new algorithms. There is currently no
mechanism to do this aside from copying the data manually into a new
filesystem with the new algorithm enabled. This tool allows the
transformation to happen through zfs send, allowing it to be done
efficiently to remote systems and in an incremental fashion.
A new zstream command is added that decompresses WRITE records and
then recompresses them with a provided algorithm, and then re-emits
the modified send stream. It may also be possible to re-compress
embedded block pointers, but that was not attempted for the initial
version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#14106
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
The quota for ZVOLs is set to the size of the volume. When the quota
reaches the maximum, there isn't an excellent way to check if the new
writers are overwriting the data or if they are inserting a new one.
Because of that, when we reach the maximum quota, we wait till txg is
flushed. This is causing a significant fluctuation in bandwidth.
In the case of ZVOL, the quota is enforced by the volsize, so we
can omit it.
This commit adds a sysctl thats allow to control if the quota mechanism
should be enforced or not.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Zededa Inc.
Sponsored-by: Klara Inc.
Closes#13838
This allows for printing a machine-readable, accurate to the second,
hold creation time in the form of a unix epoch timestamp.
Additionally, updates relevant documentation and man pages accordingly.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mohamed Tawfik <m_tawfik@aucegypt.edu>
Closes#13690Closes#14152
Some of our customers have been occasionally hitting zfs import failures
in Linux because udevd doesn't create the by-id symbolic links in time
for zpool import to use them. The main issue is that the
systemd-udev-settle.service that zfs-import-cache.service and other
services depend on is racy. There is also an openzfs issue filed (see
https://github.com/openzfs/zfs/issues/10891) outlining the problem and
potential solutions.
With the proper solutions being significant in terms of complexity and
the priority of the issue being low for the time being, this patch
exposes `zfs_vdev_open_timeout_ms` as a tunable so people that are
experiencing this issue often can increase it as a workaround.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14133
Currently, additional/extra copies are created for metadata in
addition to the redundancy provided by the pool(mirror/raidz/draid),
due to this 2 times more space is utilized per inode and this decreases
the total number of inodes that can be created in the filesystem. By
setting redundant_metadata to none, no additional copies of metadata
are created, hence can reduce the space consumed by the additional
metadata copies and increase the total number of inodes that can be
created in the filesystem. Additionally, this can improve file create
performance due to the reduced amount of metadata which needs
to be written.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#13680
If a record is uncompressed on-disk but the block pointer insists
otherwise, reading it will return EIO. This commit adds an "off" type
to the "zstream decompress" command. Using it will set the compression
field in a zfs stream to "off" without changing the record's data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alan Somers <asomers@FreeBSD.org>
Sponsored by: Axcient
Closes#13997
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
The current value causes significant artificial slowdown during mass
parallel file removal, which can be observed both on FreeBSD and Linux
when running real workloads.
Sample results from Linux doing make -j 96 clean after an allyesconfig
modules build:
before: 4.14s user 6.79s system 48% cpu 22.631 total
after: 4.17s user 6.44s system 153% cpu 6.927 total
FreeBSD results in the ticket.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13932Closes#13938
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Incorrectly sizing the array of hash locks used to protect the
dbuf hash table can lead to contention and reduce performance.
We could unconditionally allocate a larger array for the locks
but it's wasteful, particularly for a low-memory system.
Instead, dynamically allocate the array of locks and scale
it based on total system memory.
Additionally, add a new `dbuf_mutex_cache_shift` module option
which can be used to override the hash lock array size. This is
disabled by default (dbuf_mutex_hash_shift=0) and can only be
set at module load time. The minimum target array size is set
to 8192, this matches the current constant value.
Note that the count of the dbuf hash table and count of the
mutex array were added to the /proc/spl/kstat/zfs/dbufstats
kstat.
Finally, this change removes the _KERNEL conditional checks.
These were not required since for the user space build there
is no difference between the kmem and vmem interfaces.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13928
The zfs module parameter zfs_blake3_impl got no manual page entry while
adding BLAKE3 to OpenZFS. This commit adds the required notes about the
parameter into zfs.4
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@freqlabs.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
I see a few issues in the issue tracker that might be aided by being
able to turn this on. We have no module parameter for it, so I would
like to add one.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13874
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
Only the single snapshot rename is provided.
The recursive or more complex rename can be scripted.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#13802
Currently, snapshots_changed property is stored in dd_props_zapobj, due
to which the property is assumed to be local. This causes a difference
in behavior with respect to other readonly properties.
This commit stores the snapshots_changed property in dd_object. Source
is not set to local in this case, which makes it consistent with other
readonly properties.
This commit also updates the date string format to include seconds.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13785
When scrubbing an encrypted filesystem with unloaded key still report an
error in zpool status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13675Closes#13717
There are a couple changes included here. The first is to introduce
a cap on the size the ZED will grow the zevent list to. One million
entries is more than enough for most use cases, and if you are
overflowing that value, the problem needs to be addressed another
way. The value is also tunable, for those who want the limit to be
higher or lower.
The other change is to add a kernel module parameter that allows
snapshot creation/deletion to be exempted from the history logging;
for most workloads, having these things logged is valuable, but for
some workloads it produces large quantities of log spam and isn't
especially helpful.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #13374Closes#13753
Linux sets relatime on mount by default for any file system,
but relatime=off in ZFS disables it explicitly.
Let's be consistent with other file systems on Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#13614
Make dd_snap_cmtime property persistent across mount and unmount
operations by storing in ZAP and restore the value from ZAP on hold
into dd_snap_cmtime instead of updating it.
Expose dd_snap_cmtime as 'snapshots_changed' property that provides a
mechanism to quickly determine whether snapshot list for dataset has
changed without having to mount a dataset or iterate the snapshot list.
It specifies the time at which a snapshot for a dataset was last
created or deleted. This allows us to be more efficient how often we
query snapshots.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13635
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
It can be used to repair a ZFS file system corrupted by ZFS bug #12762.
Use it like this:
zfs send -c <DS> | \
zstream decompress <OBJECT>,<OFFSET>[,<COMPRESSION_ALGO>] ... | \
zfs recv <DST_DS>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Alan Somers <asomers@gmail.com>
Sponsored-by: Axcient
Workaround for #12762Closes#13256
Use Dq,Pq/Po/Pc macros. illumos dumpadm is now in section 8.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#13586
On machines using systemd, trim timers can be enabled on a per-pool
basis. Weekly and monthly timer units are provided. Timers can be
enabled as follows:
systemctl enable zfs-trim-weekly@rpool.timer --now
systemctl enable zfs-trim-monthly@datapool.timer --now
Each timer will pull in zfs-trim@${poolname}.service, which is not
schedule-specific.
The manpage zpool-trim has been updated accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Julian Brunner <julian.brunner@gmail.com>
Closes#13544
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
Add support for the kernel's block multiqueue (blk-mq) interface in
the zvol block driver. blk-mq creates multiple request queues on
different CPUs rather than having a single request queue. This can
improve zvol performance with multithreaded reads/writes.
This implementation uses the blk-mq interfaces on 4.13 or newer
kernels. Building against older kernels will fall back to the
older BIO interfaces.
Note that you must set the `zvol_use_blk_mq` module param to
enable the blk-mq API. It is disabled by default.
In addition, this commit lets the zvol blk-mq layer process whole
`struct request` IOs at a time, rather than breaking them down
into their individual BIOs. This reduces dbuf lock contention
and overhead versus the legacy zvol submit_bio() codepath.
sequential dd to one zvol, 8k volblocksize, no O_DIRECT:
legacy submit_bio() 292MB/s write 453MB/s read
this commit 453MB/s write 885MB/s read
It also introduces a new `zvol_blk_mq_chunks_per_thread` module
parameter. This parameter represents how many volblocksize'd chunks
to process per each zvol thread. It can be used to tune your zvols
for better read vs write performance (higher values favor write,
lower favor read).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13148
Issue #12483
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
That'll teach me to try and recall them from the definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13519
The EXTRA_DIST variable is ignored when used in the FALSE conditional
of a Makefile.am. This results in the `make dist` target omitting
these files from the generated tarball unless CONFIG_USER is defined.
This issue can be avoided by switching to use the dist_noinst_DATA
variable which is handled as expected by autoconf.
This change also adds support for --with-config=dist as an alias
for --with-config=srpm and updates the GitHub workflows to use it.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13459Closes#13505
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
The short-path is now one access() call,
we always modprobe zfs (ZFS_MODULE_LOADING which doesn't use the libzfs
boolean parsing is gone),
and we use a simple inotify IN_CREATE loop with a timerfd timeout
rather than 10ms kernel-style polling
There's one substantial difference: ZFS_MODULE_TIMEOUT=-1
now means "never give up", rather than "wait 10 minutes"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13330
This changes the behaviour of -B from the illumos one which would,
in the example in the manual, take just ./chroots/lenny;
this, however, is more versatile, and scales much better for systems
with ZFS in /usr/local, for example
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13411Closes#1770
No installation diff, dist lost
-zfs-2.1.99/cmd/fsck_zfs/fsck.zfs
which was distributed erroneously, since it's generated
Also clean gitrev on clean
Also add -e 'any possible bashisms' to default checkbashisms flags,
and fully parallelise it and shellcheck, and it works out-of-tree, too
Also align the Release in the dist META file correctly
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13316
Linux has an unresolved hang if you resize a pipe with bytes
in it.
Since there's no obvious way to detect this happening, added a
workaround to disable resizing the pipe buffer if you set an
environment variable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13309
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
Also clean up the horrendously verbose -X handling in zfs_main()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13352
Thorough documentation with a dracut.bootup(7)-style flowchart,
dracut.cmdline(7)-style cmdline listing,
and per-file docs like the old README
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13291
Provide explicit requirements towards file system naming convention
in OpenZFS man pages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Mitigates #13310Closes#13315
Remove handling for allowing doxygen- and embedding in splint(?)-style
comments. This functionality is unused by OpenZFS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13264
Add support for a -exclude/-X option to `zfs send` to allow dataset
hierarchies to be excluded.
Snapshots can be excluded using a channel program; however,
this can result in failures with 'zfs send -R'; this option allows
them to be excluded. Fortunately, this required a change only to
cmd/zfs/zfs_main.c, using the already-existing callback argument
to zfs_send() that is currently unused.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sean Eric Fagan <kithrup@mac.com>
Signed-off-by: Sean Eric Fagan <kithrup@mac.com>
Closes#13158
A simple change, but so many tests break with it,
and those are the majority of this.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13078
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
It's noted very scarcely in the code as it stands, indeed the only
actual comment on this is
/*
* We have finished background destroying, but there is still
* some space left in the dp_free_dir. Transfer this leaked
* space to the dp_leak_dir.
*/
Introduced in fbeddd60b7 ("Illumos 4390 -
I/O errors can corrupt space map when deleting fs/vol"),
which explains, alongside the references, that this can only happen
with a corrupted pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13081
Should be `-o keyformat=passphrase` instead of `-o -keyformat=passphrase`
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chuang Zhu <chuang@melty.land>
Closes#13072
zdb -d <pool>/<objset ID> does not work when
other command line arguments are included i.e.
zdb -U <cachefile> -d <pool>/<objset ID>
This change fixes the command line parsing
to handle this situation. Also fix issue
where zdb -r <dataset> <file> does not handle
the root <dataset> of the pool. Introduce -N
option to force <objset ID> to be interpreted
as a numeric objsetID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12845Closes#12944
Nowhere in the description of the failmode property does it
clearly state how to bring a suspended pool back online.
Add a few words to property description and the zpool-clear(8)
man page.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12907Closes#9395
This change introduces long options for zdb. It updates the usage
message as well to include the long options.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Manoj Joseph <manoj.joseph@delphix.com>
Closes#12818
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
Timers can be enabled as follows:
systemctl enable zfs-scrub-weekly@rpool.timer --now
systemctl enable zfs-scrub-monthly@datapool.timer --now
Each timer will pull in zfs-scrub@${poolname}.service, which is not
schedule-specific.
Added PERIODIC SCRUB section to zpool-scrub.8.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#12193
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12746
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Max Zettlmeißl <max@zettlmeissl.de>
Closes#12784
Sometimes, we'd like to know info about the metaslab groups
on special vdevs too. So let's make -MM do something useful.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12750
* etc/systemd/zfs-mount-generator: serialise
The wins for a relatively normal workload are rather slim:
real 0.02119s/0.00985s=2.15029x
user 0.02130s/0.00346s=6.15560x
sys 0.03858s/0.00643s=6.00062x
wall-total 0.014518s/0.005925s=2.45009x
wall-init 0.014518s/0.002457s=5.90684x
wall-real 0.014518s/0.003467s=4.18668x
But this is a big win on machines with a lot of datasets and expensive
forks.
For example, the gain on a VM on my work laptop with 900+ legacy-mount
Docker datasets, the original gains from the C rewrite were
only five-fold:
real 0.516s/0.102s=5.05882x
user 0.237s/0.143s=1.65734x
sys 0.287s/0.100s=2.87x
And this serial variant gains this back there as well:
real 0.102s/0.008s=12.75x
user 0.143s/0.007s=20.42857
sys 0.100s/0.001s=100x
wall-total 0.09717s/0.00319s=30.40255x
wall-init 0.00203s/0.00200s=1.015941x
wall-real 0.09513s/0.00118s=80.02043x
For a total of
real 0.516s/0.008s=64.5x
user 0.237s/0.007s=33.85714x
sys 0.287s/0.001s=287x
Suggested-by: Richard Laager <rlaager@wiktel.com>
* etc/systemd/zfs-mount-generator: pull in network for keylocation=https
Also simplify RequiresMountsFor= handling
Ref: #11956
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12138
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Update zpool.8 to avoid parseltongue.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Piotr P. Stefaniak <pstef@freebsd.org>
Closes#12763
The code is integrated, builds fine, runs fine, there's not really
any reason not to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12735
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
In case if all label checksums will be invalid on any vdev, the pool
will become unimportable. The zhack with newly added cli options could
be used to restore label checksums and make pool importable again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#2510Closes#12686
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
This change primarily seeks to make implicit documentation explicit, as
it is not outright stated that options should be comma-separated, nor is
there a reason given for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Daniel Ebdrup Jensen <debdrup@FreeBSD.org>
Closes#12579
Recognize when the host part of a sharenfs attribute is an ipv6
Literal and pass that through without modification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
Closes: #11171Closes#11939Closes: #1894
One might expect "send data as it is on disk, and cannot trigger
compression changes" to imply "does not attempt to compress data
that was not compressed on the sender."
One would be mistaken.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12570
Previously, zpool-iostat did not display any data regarding rebuild I/Os
in either the latency/size histograms (-w/-l/-r) or the queue data (-q).
This fix essentially utilizes the existing infrastructure for tracking
rebuild queue data and displays this data in the proper places within
zpool-iostat's output.
Signed-off-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Signed-off-by: Trevor Bautista <tbautista@lanl.gov>
Co-authored-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Document that top-level vdevs cannot be removed unless all top-level
vdevs have the same sector size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Sam Hathaway <sam@sam-hathaway.com>
Closes#11339Closes#12472
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Gordon Bergling <gbergling@googlemail.com>
Closes#12464
Many things has changed since previous default was set many years ago.
Nowadays 8KB does not allow adequate compression or even decent space
efficiency on many of pools due to 4KB disk physical block rounding,
especially on RAIDZ and DRAID. It effectively limits write throughput
to only 2-3GB/s (250-350K blocks/s) due to sync thread, allocation,
vdev queue and other block rate bottlenecks. It keeps L2ARC expensive
despite many optimizations and dedup just unrealistic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12406
Describe sequential scrub and add examples of scrub status.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#12429
* Add Module Parameters Regarding Log Size Limit
zfs_wrlog_data_max
The upper limit of TX_WRITE log data. Once it is reached,
write operation is blocked, until log data is cleared out
after txg sync. It only counts TX_WRITE log with WR_COPIED
or WR_NEED_COPY.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12284
zfs-send(8) claimed in the flags list you could use -pR when sending
a readonly filesystem or volume. You cannot.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12336
arc_evict_hdr() returns number of evicted bytes in scope of specific
state. For ghost states it does not mean the amount of really freed
memory, but the logical buffer size. It is correct for the eviction
process, but not for waking up threads waiting for ARC size reduction,
as added in "Revise ARC shrinker algorithm" commit, causing premature
wakeups while ARC is still overflowed, allowing even bigger overflow,
plus processing overhead when next allocation will also get blocked,
probably also for too short time.
To fix that make arc_evict_hdr() also return the amount of really
freed memory, which for the ghost states is only the header, and use
it to update arc_evict_count instead. Originally I was thinking to
not return it at all, since arc_get_data_impl() does not account for
the headers, but decided that some slow allocation progress is better
than long waits, reaching on my tests up to 100ms.
To reduce negative latency effects of long time periods when reclaim
thread can free little real memory, start reclamation process earlier,
before we actually reached the overflow threshold, when we have to
throttle new allocations. We can also do it without taking global
arc_evict_lock, reducing the contention.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12279
Most notably this fixes the vdev_id(8) non-.Xrs in vdev_id.conf.5
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12212
The prevailing style is to use either nothing, or the originating
organisational umbrella (here: OpenZFS), and these aren't Linux manpages
This also deduplicates the substitution code, and makes adding/removing
sexions simpler in future
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12212
rob-wing
George Melikov
Ameer Hamza
Mateusz Piotrowski
Mateusz Piotrowski
Alexander Motin
Ethan Coe-Renner
Allan Jude
szubersk
Paul Dagnelie
Mariusz Zaborski
Mariusz Zaborski
Mohamed Tawfik
Serapheim Dimitropoulos
Akash B
Alan Somers
Richard Yao
Mateusz Guzik
Brian Behlendorf
Tino Reichardt
Andriy Gapon
Umer Saleem
George Amanakis
Alek P
Alan Somers
Toomas Soome
Julian Brunner
Will Andrews
Tony Hutter
Rich Ercolani
наб
Mateusz Piotrowski
WHR
Sean Eric Fagan
Jitendra Patidar
Ryan Moeller
Zhu Chuang
Paul Zuchowski
chrisrd
Manoj Joseph
Georgy Yakovlev
maxz
pstef
Fedor Uporov
D. Ebdrup
felixdoerre
Trevor Bautista
Sam Hathaway
Gordon Bergling
Václav Skála
Kevin Jin