When ZFS overwrites a whole block, it does not bother to read the
old content from disk. It is a good optimization, but if the buffer
fill fails due to page fault or something else, the buffer ends up
corrupted, neither keeping old content, nor getting the new one.
On FreeBSD this is additionally complicated by page faults being
blocked by VFS layer, always returning EFAULT on attempt to write
from mmap()'ed but not yet cached address range. Normally it is
not a big problem, since after original failure VFS will retry the
write after reading the required data. The problem becomes worse
in specific case when somebody tries to write into a file its own
mmap()'ed content from the same location. In that situation the
only copy of the data is getting corrupted on the page fault and
the following retries only fixate the status quo. Block cloning
makes this issue easier to reproduce, since it does not read the
old data, unlike traditional file copy, that may work by chance.
This patch provides the fill status to dmu_buf_fill_done(), that
in case of error can destroy the corrupted buffer as if no write
happened. One more complication in case of block cloning is that
if error is possible during fill, dmu_buf_will_fill() must read
the data via fall-back to dmu_buf_will_dirty(). It is required
to allow in case of error restoring the buffer to a state after
the cloning, not not before it, that would happen if we just call
dbuf_undirty().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rob Norris <robn@despairlabs.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15665
musl libc has deprecated LFS64 aliases, so bootstrapping FreeBSD tools
under musl distros has been failing with stat64 errors.
Apply the aliases under non-glibc Linux to fix this problem.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Val Packett <val@packett.cool>
Closes#15780
Since we use a limited set of kmem caches, quite often we have unused
memory after the end of the buffer. Put there up to a 512-byte canary
when built with debug to detect buffer overflows at the free time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15553
FreeBSD/powerpc64 is all ELFv2 since FreeBSD 13, even big endian. The
existing sha256 and sha512 asm code assumes that BE is all ELFv1, and LE
is ELFv2. Minor changes to add ELFv2 in the BE side gets this working
correctly on FreeBSD with latest OpenZFS import.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Justin Hibbits <chmeeedalf@gmail.com>
Closes#14779
Add loongarch64 definitions & lua module setjmp asm
LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Han Gao <gaohan@uniontech.com>
Signed-off-by: WANG Xuerui <xen0n@gentoo.org>
Closes#13422
Commit 11913870 (#14567) added cmn_err_once() by #define'ing a
compound statement but failed to consider usage in a single
statement brace-less if else.
Fix the problem by using the common "do {} while (0)" construct.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14629
Under some configurations, GCC didn't predefined macro 'powerpc' for
such a target. Use the guaranteed macro '__powerpc__' instead.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#14631
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14567
These are added via HWCAP interface:
- zfs_neon_available() for arm and aarch64
- zfs_sha256_available() for arm and aarch64
- zfs_sha512_available() for aarch64
This one via cpuid() call:
- zfs_shani_available() for x86_64
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
We had three sha2.h headers in different places.
The FreeBSD version, the Linux version and the generic solaris version.
The only assembly used for acceleration was some old x86-64 openssl
implementation for sha256 within the icp module.
For FreeBSD the whole SHA2 files of FreeBSD were copied into OpenZFS,
these files got removed also.
Tested-by: Rich Ercolani <rincebrain@gmail.com>
Tested-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13741
In commit 0a5b942d4 the FreeBSD SECTION_STATIC macro was set to
".rodata". This assembler directive is supported by LLVM (as a
convenience alias for ".section .rodata") by not by GNU as.
This caused the FreeBSD builds that are done with gcc to fail.
Therefore, use ".section .rodata" instead, similar to the other
asm_linkage.h headers.
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Dimitry Andric <dimitry@andric.com>
Closes#14526
In https://github.com/openzfs/zfs/pull/14228 the FreeBSD
SECTION_STATIC was set to ".data" instead of ".rodata". This
commit just restores it back to .rodata.
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14460
The .align directive used to align storage locations is
ambiguous. On some platforms and assemblers it takes a byte count,
on others the argument is interpreted as a shift value. The current
usage expects the first interpretation.
Replace it with the unambiguous .balign directive which always
expects a byte count, regardless of platform and assembler.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14422
Add new macro ASMABI used by Windows to change
calling API to "sysv_abi".
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#14228
Most of this file was a pile of defines, apparently from Solaris that
controlled nothing in the source tree. A few things controlled the
definition of unused types or macros which I have removed.
Considerable further cleanup is possible including removal of
architectures FreeBSD never supported. This file should likely converge
with the Linux version to the extent possible.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
Check __riscv_xlen == 64 rather than _LP64 and define _LP64 if missing.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14128
`snprintf()` is meant to protect against buffer overflows, but operating
on the buffer using its return value, possibly by calling it again, can
cause a buffer overflow, because it will return how many characters it
would have written if it had enough space even when it did not. In a
number of places, we repeatedly call snprintf() by successively
incrementing a buffer offset and decrementing a buffer length, by its
return value. This is a potentially unsafe usage of `snprintf()`
whenever the buffer length is reached. CodeQL complained about this.
To fix this, we introduce `kmem_scnprintf()`, which will return 0 when
the buffer is zero or the number of written characters, minus 1 to
exclude the NULL character, when the buffer was too small. In all other
cases, it behaves like snprintf(). The name is inspired by the Linux and
XNU kernels' `scnprintf()`. The implementation was written before I
thought to look at `scnprintf()` and had a good name for it, but it
turned out to have identical semantics to the Linux kernel version.
That lead to the name, `kmem_scnprintf()`.
CodeQL only catches this issue in loops, so repeated use of snprintf()
outside of a loop was not caught. As a result, a thorough audit of the
codebase was done to examine all instances of `snprintf()` usage for
potential problems and a few were caught. Fixes for them are included in
this patch.
Unfortunately, ZED is one of the places where `snprintf()` is
potentially used incorrectly. Since using `kmem_scnprintf()` in it would
require changing how it is linked, we modify its usage to make it safe,
no matter what buffer length is used. In addition, there was a bug in
the use of the return value where the NULL format character was not
being written by pwrite(). That has been fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
Windows port frees memory that was alloc'd aligned in a different way
then alloc'd memory. So changing frees to be specific.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Innes <andrew.c12@gmail.com>
Co-Authored-By: Jorgen Lundman <lundman@lundman.net>
Closes#14059
Coverity made two complaints about this function. The first is that we
ignore the number of bytes read. The second is that we have a sizeof
mismatch.
On 64-bit systems, long is a 64-bit type. Paradoxically, the standard
says that hostid is 32-bit, yet is also a long type. On 64-bit big
endian systems, reading into the long would cause us to return 0 as our
hostid after the mask. This is wrong.
Also, if a partial read were to happen (it should not), we would return
a partial hostid, which is also wrong.
We introduce a uint32_t system_hostid stack variable and ensure that the
read is done into it and check the read's return value. Then we set the
value based on whether the read was successful. This should fix both of
coverity's complaints.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13968
Both Clang's Static Analyzer and Synopsys' Coverity would ignore
assertions. Following Clang's advice, we annotate our assertions:
https://clang-analyzer.llvm.org/annotations.html#custom_assertions
This makes both Clang's Static Analyzer and Coverity properly identify
assertions. This change reduced Clang's reported defects from 246 to
180. It also reduced the false positives reported by Coverityi by 10,
while enabling Coverity to find 9 more defects that previously were
false negatives.
A couple examples of this would be CID-1524417 and CID-1524423. After
submitting a build to coverity with the modified assertions, CID-1524417
disappeared while the report for CID-1524423 no longer claimed that the
assertion tripped.
Coincidentally, it turns out that it is possible to more accurately
annotate our headers than the Coverity modelling file permits in the
case of format strings. Since we can do that and this patch annotates
headers whenever `__coverity_panic__()` would have been used in the
model file, we drop all models that use `__coverity_panic__()` from the
model file.
Upon seeing the success in eliminating false positives involving
assertions, it occurred to me that we could also modify our headers to
eliminate coverity's false positives involving byte swaps. We now have
coverity specific byteswap macros, that do nothing, to disable
Coverity's false positives when we do byte swaps. This allowed us to
also drop the byteswap definitions from the model file.
Lastly, a model file update has been done beyond the mentioned
deletions:
* The definitions of `umem_alloc_aligned()`, `umem_alloc()` andi
`umem_zalloc()` were originally implemented in a way that was
intended to inform coverity that when KM_SLEEP has been passed these
functions, they do not return NULL. A small error in how this was
done was found, so we correct it.
* Definitions for umem_cache_alloc() and umem_cache_free() have been
added.
In practice, no false positives were avoided by making these changes,
but in the interest of correctness from future coverity builds, we make
them anyway.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13902
Coverity caught unsafe use of `strcpy()` in `ztest_dmu_objset_own()`,
`nfs_init_tmpfile()` and `dump_snapshot()`. It also caught an unsafe use
of `strlcat()` in `nfs_init_tmpfile()`.
Inspired by this, I did an audit of every single usage of `strcpy()` and
`strcat()` in the code. If I could not prove that the usage was safe, I
changed the code to use either `strlcpy()` or `strlcat()`, depending on
which function was originally used. In some cases, `snprintf()` was used
to replace multiple uses of `strcat` because it was cleaner.
Whenever I changed a function, I preferred to use `sizeof(dst)` when the
compiler is able to provide the string size via that. When it could not
because the string was passed by a caller, I checked the entire call
tree of the function to find out how big the buffer was and hard coded
it. Hardcoding is less than ideal, but it is safe unless someone shrinks
the buffer sizes being passed.
Additionally, Coverity reported three more string related issues:
* It caught a case where we do an overlapping memory copy in a call to
`snprintf()`. We fix that via `kmem_strdup()` and `kmem_strfree()`.
* It caught `sizeof (buf)` being used instead of `buflen` in
`zdb_nicenum()`'s call to `zfs_nicenum()`, which is passed to
`snprintf()`. We change that to pass `buflen`.
* It caught a theoretical unterminated string passed to `strcmp()`.
This one is likely a false positive, but we have the information
needed to do this more safely, so we change this to silence the false
positive not just in coverity, but potentially other static analysis
tools too. We switch to `strncmp()`.
* There was a false positive in tests/zfs-tests/cmd/dir_rd_update.c. We
suppress it by switching to `snprintf()` since other static analysis
tools might complain about it too. Interestingly, there is a possible
real bug there too, since it assumes that the passed directory path
ends with '/'. We add a '/' to fix that potential bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13913
The extern declaration is only for Linux, move this line
into the right #ifdef section.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Martin Matuska <mm@FreeBSD.org>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13934Closes#13936
Provides the missing full barrier variant to the membar primitive set.
While not used right now, this is probably going to change down the
road.
Name taken from Solaris, to follow the existing routines.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13907
Add needed cpu feature tests for powerpc architecture.
Overview:
zfs_altivec_available() - needed by RAID-Z
zfs_vsx_available() - needed by BLAKE3
zfs_isa207_available() - needed by SHA2
Part 1 - Userspace
- use getauxval() for Linux and elf_aux_info() for FreeBSD
- direct including <sys/auxv.h> fails with double definitions
- so we self define the needed functions and definitions
Part 2 - Kernel space FreeBSD
- use exported cpu_features of <powerpc/cpu.h>
Part 3 - Kernel space Linux
- use cpu_has_feature() function of <asm/cpufeature.h>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13725
The are a few cases where stale entries in /etc/exports.d/zfs.exports
will cause the nfs-server service to fail when starting up.
Since the nfs-server startup consumes /etc/exports.d/zfs.exports, the
zfs-share service (which rebuilds the list of zfs exports) should run
before the nfs-server service.
To make the zfs-share service resilient to stale exports, this change
truncates the zfs config file as part of the zfs share -a operation.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#13775
Follow up fix for a926aab902.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13348Closes#13610
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
Makes getmntent and getmntany thread-safe for external consumers of
libzfs zpool_disable_datasets, zfs_iter_mounted, libzfs_mnttab_update,
libzfs_mnttab_find.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13484
Even on Illumos it's only available in the 32-bit programming
environment, and, quoth enable_extended_FILE_stdio(3C):
> Historically, 32-bit Solaris applications have been limited to using
> only the file descriptors 0 through 255 with the standard I/O
> functions (see stdio(3C)) in the C library. The extended FILE
> facility allows well-behaved 32-bit applications to use any
> valid file descriptor with the standard I/O functions.
where "well-behaved" means that it
> does not directly access any fields in the FILE structure pointed
> to by the FILE pointer associated with any standard I/O stream,
And the stdio/flush.c implementation reads:
/*
* if this is not an internal extended FILE then check
* if _file is being changed from underneath us.
* It should not be because if
* it is then then we lose our ability to guard against
* silent data corruption.
*/
if (!iop->__xf_nocheck && bad_fd > -1 && iop->_magic != bad_fd) {
(void) fprintf(stderr,
"Application violated extended FILE safety mechanism.\n"
"Please read the man page for extendedFILE.\nAborting\n");
abort();
}
This appears to be an insane workaround for broken implementation with
exposed FILE internals and _file being an u8, both only on non-LP64;
it's shimmed out on all LP64 targets in Illumos,
and we shim it out as well: just get rid of it
This appears to've been originally fixed in illumos-gate
a5f69788de7ac07553de47f7fec8c05a9a94c105 ("PSARC 2006/162 Extended FILE
space for 32-bit Solaris processes", "1085341 32-bit stdio routines
should support file descriptors >255"), which also bears extendedFILE
and enable_extended_FILE_stdio(3C):
- unsigned char _file; /* UNIX System file descriptor */
+ unsigned char _magic; /* Old home of the file descriptor */
+ /* Only fileno(3C) can retrieve the
value now */
and
+/*
+ * Macros to aid the extended fd FILE work.
+ * This helps isolate the changes to only the 32-bit code
+ * since 64-bit Solaris is not affected by this.
+ */
+#ifdef _LP64
+#define GET_FD(iop) ((iop)->_file)
+#define SET_FILE(iop, fd) ((iop)->_file = (fd))
+#else
+#define GET_FD(iop) \
+ (((iop)->__extendedfd) ? _file_get(iop) : (iop)->_magic)
+#define SET_FILE(iop, fd) (iop)->_magic = (fd); (iop)->__extendedfd = 0
+#endif
Also remove the 1k setrlimit(NOFILE) calls: that's the default on Linux,
with 64k on Illumos and 171k on FreeBSD
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13411
- Prefer O_* flags over F* flags that mostly mirror O_* flags anyway,
but O_* flags seem to be preferred.
- Simplify the code as all the F*SYNC flags were defined as FFSYNC flag.
- Don't define FRSYNC flag, so we don't generate unnecessary ZIL commits.
- Remove EXCL define, FreeBSD ignores the excl argument for zfs_create()
anyway.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13400
For #13083, curiously, it did not print the actual error, just
that the compile failed with "Error 1".
In theory, this flag should cause it to report errors twice sometimes.
In practice, I'm pretty okay with reporting some twice if it avoids
reporting some never.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13086
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
aarch64 is a different architecture than arm. Some
compilers might choke when both __arm__ and __aarch64__
are defined.
This change separates the checks for arm and for
aarch64 in the isa_defs.h header files.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Windel Bouwman <windel@windel.nl>
Closes#10335Closes#13151
A function that returns with no value is a different thing from a
function that doesn't return at all. Those are two orthogonal
concepts, commonly confused.
pthread_create(3) expects a pointer to a start routine that has a
very precise prototype:
void *(*start_routine)(void *);
However, other thread functions, such as kernel ones, expect:
void (*start_routine)(void *);
Providing a different one is incorrect, and has only been working
because the ABIs happen to produce a compatible function.
We should use '_Noreturn void', since it's the natural type, and
then provide a '_Noreturn void *' wrapper for pthread functions.
For consistency, replace most cases of __NORETURN or
__attribute__((noreturn)) by _Noreturn. _Noreturn is understood
by -std=gnu89, so it should be safe to use everywhere.
Ref: https://github.com/openzfs/zfs/pull/13110#discussion_r808450136
Ref: https://software.codidact.com/posts/285972
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alejandro Colomar <alx.manpages@gmail.com>
Closes#13120
Alexander Motin
Val Packett
Richard Yao
Justin Hibbits
Han Gao
Attila Fülöp
Low-power
Tino Reichardt
Dimitry Andric
Jorgen Lundman
Brooks Davis
Andrew Innes
Mateusz Guzik
Don Brady
наб
Will Andrews
Ryan Moeller
Pawel Jakub Dawidek
Rich Ercolani
Windel Bouwman
Alejandro Colomar