The name of the flag used to mark a bio as synchronous has changed
again in the 2.6.36 kernel due to the unification of the BIO_RW_*
and REQ_* flags. The new flag is called REQ_SYNC. To simplify
checking this flag I have introduced the vdev_disk_dio_is_sync()
helper function. Based on the results of several new autoconf
tests it uses the correct mask to check for a synchronous bio.
Preferred interface for flagging a synchronous bio:
2.6.12-2.6.29: BIO_RW_SYNC
2.6.30-2.6.35: BIO_RW_SYNCIO
2.6.36-2.6.xx: REQ_SYNC
As of linux-2.6.36 the BIO_RW_FAILFAST and REQ_FAILFAST flags
have been unified under the REQ_* names. These flags always had
to be kept in-sync so this is a nice step forward, unfortunately
it means we need to be careful to only use the new unified flags
when the BIO_RW_* flags are not defined. Additional autoconf
checks were added for this and if it is ever unclear which method
to use no flags are set. This is safe but may result in longer
delays before a disk is failed.
Perferred interface for setting FAILFAST on a bio:
2.6.12-2.6.27: BIO_RW_FAILFAST
2.6.28-2.6.35: BIO_RW_FAILFAST_{DEV|TRANSPORT|DRIVER}
2.6.36-2.6.xx: REQ_FAILFAST_{DEV|TRANSPORT|DRIVER}
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
The spl_config.h file is checked to determine the spl version.
However, the zfs code was looking for it in the source directory
and not the build directory.
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
Brian Behlendorf