This commit adds support for zpool status command to displpay status
of ZFS pools in JSON format using '-j' option. Status information is
collected in nvlist which is later dumped on stdout in JSON format.
Existing options for zpool status work with '-j' flag. man page for
zpool status is updated accordingly.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#16217
This change adds a new `zpool prefetch -t ddt $pool` command which
causes a pool's DDT to be loaded into the ARC. The primary goal is to
remove the need to "warm" a pool's cache before deduplication stops
slowing write performance. It may also provide a way to reload portions
of a DDT if they have been flushed due to inactivity.
Sponsored-by: iXsystems, Inc.
Sponsored-by: Catalogics, Inc.
Sponsored-by: Klara, Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Fred Weigel <fred.weigel@klarasystems.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Will Andrews <will.andrews@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Closes#15890
This adds two new pool properties:
- dedup_table_size, the total size of all DDTs on the pool; and
- dedup_table_quota, the maximum possible size of all DDTs in the pool
When set, quota will be enforced by checking when a new entry is about
to be created. If the pool is over its dedup quota, the entry won't be
created, and the corresponding write will be converted to a regular
non-dedup write. Note that existing entries can be updated (ie their
refcounts changed), as that reuses the space rather than requiring more.
dedup_table_quota can be set to 'auto', which will set it based on the
size of the devices backing the "dedup" allocation device. This makes it
possible to limit the DDTs to the size of a dedup vdev only, such that
when the device fills, no new blocks are deduplicated.
Sponsored-by: iXsystems, Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Co-authored-by: Sean Eric Fagan <sean.fagan@klarasystems.com>
Closes#15889
Sponsored-by: Klara, Inc.
Sponsored-By: Wasabi Technology, Inc.
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
If it's going to be used directly by zdb/ztest, then it sort of doesn't
make sense to carry it with the assert code.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#16181
Ever since a10d50f999, ZFS has mounted file systems in parallel when
importing a pool. It uses a fixed size of 512 for the thread pool. But
since c183d164aa, it has also imported pools in parallel. So the total
number of threads at one time is 513 * npools + 1. That can easily
exceed the system's limit on the number of threads per process, which
will cause one or more pools to be unable to allocate any worker
threads, forcing them to fallback to slow serial mounting . To
forestall that, manage the threadpool size in /sbin/zpool, not libzfs.
Use the same size (512), but divided by the number of pools.
This is a backwards-incompatible change to the libzfs abi.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Alan Somers <asomers@FreeBSD.org>
Closes#16178
Currently, zpool add allows users to add top-level vdevs that have
different ashifts but doing so prevents users from being able to
perform a top-level vdev removal. Often times consumers may not realize
that they have mismatched ashifts until the top-level removal fails.
This feature adds ashift validation to the zpool add command and will
fail the operation if the sector size of the specified vdev does not
match the existing pool. This behavior can be disabled by using the -f
flag. In addition, new flags have been added to provide fine-grained
control to disable specific checks. These flags
are:
--allow-in-use
--allow-ashift-mismatch
--allow-replicaton-mismatch
The force flag will disable all of these checks.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Maybee <mmaybee@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#15509
Slow disk response times can be indicative of a failing drive. ZFS
currently tracks slow I/Os (slower than zio_slow_io_ms) and generates
events (ereport.fs.zfs.delay). However, no action is taken by ZED,
like is done for checksum or I/O errors. This change adds slow disk
diagnosis to ZED which is opt-in using new VDEV properties:
VDEV_PROP_SLOW_IO_N
VDEV_PROP_SLOW_IO_T
If multiple VDEVs in a pool are undergoing slow I/Os, then it skips
the zpool_vdev_degrade().
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Rob Wing <rob.wing@klarasystems.com>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15469
Add `zpool` flags to control the slot power to drives. This assumes
your SAS or NVMe enclosure supports slot power control via sysfs.
The new `--power` flag is added to `zpool offline|online|clear`:
zpool offline --power <pool> <device> Turn off device slot power
zpool online --power <pool> <device> Turn on device slot power
zpool clear --power <pool> [device] Turn on device slot power
If the ZPOOL_AUTO_POWER_ON_SLOT env var is set, then the '--power'
option is automatically implied for `zpool online` and `zpool clear`
and does not need to be passed.
zpool status also gets a --power option to print the slot power status.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mart Frauenlob <AllKind@fastest.cc>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15662
This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
There have been rare cases where the VDEV_ENC_SYSFS_PATH value that zed
gets passed is stale. To mitigate this, dynamically check the sysfs
path at the time of zed event processing, and use the dynamic value if
possible. Note that there will be other times when we can not
dynamically detect the sysfs path (like if a disk disappears) and have
to rely on the old value for things like turning on the fault LED. That
is to say, we can't just blindly use the dynamic path in every case.
Also:
- Add enclosure sysfs entry when running 'zpool add'
- Fix 'slot' and 'enc' zpool.d scripts for nvme
Reviewed-by: Don Brady <dev.fs.zfs@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15462
Currently, zvol threading can be switched through the zvol_request_sync
module parameter system-wide. By making it a zvol property, zvol
threading can be switched per zvol.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#15409
ZFS prefetch is currently governed by the zfs_prefetch_disable
tunable. However, this is a module-wide settings - if a specific
dataset benefits from prefetch, while others have issue with it,
an optimal solution does not exists.
This commit introduce the "prefetch" tri-state property, which enable
granular control (at dataset/volume level) for prefetching.
This patch does not remove the zfs_prefetch_disable, which remains
a system-wide switch for enable/disable prefetch. However, to avoid
duplication, it would be preferable to deprecate and then remove
the module tunable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Co-authored-by: Gionatan Danti <g.danti@assyoma.it>
Closes#15237Closes#15436
This commit adds '-u' flag for zfs set operation. With this flag,
mountpoint, sharenfs and sharesmb properties can be updated
without actually mounting or sharing the dataset.
Previously, if dataset was unmounted, and mountpoint property was
updated, dataset was not mounted after the update. This behavior
is changed in #15240. We mount the dataset whenever mountpoint
property is updated, regardless if it's mounted or not.
To provide the user with option to keep the dataset unmounted and
still update the mountpoint without mounting the dataset, '-u'
flag can be used.
If any of mountpoint, sharenfs or sharesmb properties are updated
with '-u' flag, the property is set to desired value but the
operation to (re/un)mount and/or (re/un)share the dataset is not
performed and dataset remains as it was before.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15322
Have libzfs call a special `zfs_prepare_disk` script before a disk is
included into the pool. The user can edit this script to add things
like a disk firmware update or a disk health check. Use of the script
is totally optional. See the zfs_prepare_disk manpage for full details.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15243
Currently redaction bookmarks and their associated redaction lists
have a relatively low limit of 36 redaction snapshots. This is imposed
by the number of snapshot GUIDs that fit in the bonus buffer of the
redaction list object. While this is more than enough for most use
cases, there are some limited cases where larger numbers would be
useful to support.
We tweak the redaction list creation code to use a spill block if
the number of redaction snapshots is above the amount that would fit
in the bonus buffer. We also make a small change to allow spill blocks
to be use for types of data besides SA. In order to fully leverage
this logic, we also change the redaction code to use vmem_alloc, to
handle extremely large allocations if needed. Finally, small tweaks
were made to the zfs commands and the test suite.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#15018
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
f6a0dac84 modified the zfs_iter_* functions to take a new "flags"
parameter, and introduced a variety of flags to ask the kernel to limit
the results in various ways, reducing the amount of work the caller
needed to do to filter out things they didn't need.
Unfortunately this change broke the ABI for existing clients (read:
older versions of the `zfs` program), and was reverted 399b98198.
dc95911d2 reintroduced the original patch, with the understanding that a
backwards-compatible fix would be made before the 2.2 release branch was
tagged. This commit is that fix.
This introduces zfs_iter_*_v2 functions that have the new flags
argument, and reverts the existing functions to not have the flags
parameter, as they were before. The old functions are now reimplemented
in terms of the new, with flags set to 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Original-patch-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Closes#14597
Running `zfs list -o avail rpool` resulted in a core dump.
This commit will fix this.
Run the needed overhead only, when `use_color()` is true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#14712
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
Currently calls to kfpu_begin() and kfpu_end() are split between
the init() and fini() functions of the particular SIMD
implementation. This was done in #14247 as an optimization measure
for the ABD adapter. Unfortunately the split complicates FPU
handling on platforms that use a local FPU state buffer, like
Windows and macOS.
To ease porting, we introduce a boolean struct member in
fletcher_4_ops_t, indicating use of the FPU, and move the FPU state
handling from the SIMD implementations to the call sites.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#14600
We may try to build ZFS inside container too,
but let's just sync them for now.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#14605
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
This allows parsing of zfs send progress by checking the process
title.
Doing so requires some changes to the send code in libzfs_sendrecv.c;
primarily these changes move some of the accounting around, to allow
for the code to be verbose as normal, or set the process title. Unlike
BSD, setproctitle() isn't standard in Linux; thus, borrowed it from
libbsd with slight modifications.
Authored-by: Sean Eric Fagan <sef@FreeBSD.org>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14376
If the fields to be listed and sorted by are constrained to those
populated by dsl_dataset_fast_stat(), then zfs list is much faster,
as it does not need to open each objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name much faster.
However, it was limited to `-o name -s name`, this work extends this
optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties supported by
dsl_dataset_fast_stat() or similar, that do not require extra locking
or reading from disk.
This was committed before (9a9e2e343d),
but was reverted due to a regression when used with an older kernel.
If the kernel does not populate zc->zc_objset_stats, we now fallback
to getting the properties via the slower interface, to avoid problems
with newer userland and older kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14110
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
It appears membar_sync was not present in libzfs.abi with other
membar_* functions. This commit updates libzfs.abi for membar_sync.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13969
In libzutil, for zpool_search_import and zpool_find_config, we use
libpc_handle_t internally, which does not maintain error code and it is
not exposed in the interface. Due to this, the error information is not
propagated to the caller. Instead, an error message is printed on
stderr.
This commit adds lpc_error field in libpc_handle_t and exposes it in
the interface, which can be used by the users of libzutil to get the
appropriate error information and handle it accordingly.
Users of the API can also control if they want to print the error
message on stderr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13969
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
The are a few cases where stale entries in /etc/exports.d/zfs.exports
will cause the nfs-server service to fail when starting up.
Since the nfs-server startup consumes /etc/exports.d/zfs.exports, the
zfs-share service (which rebuilds the list of zfs exports) should run
before the nfs-server service.
To make the zfs-share service resilient to stale exports, this change
truncates the zfs config file as part of the zfs share -a operation.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#13775
This is an oddly specific function that has never had any consumers in
the history of this repo. Get rid of it and the pile of helper
functions that exist for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13724
Make dd_snap_cmtime property persistent across mount and unmount
operations by storing in ZAP and restore the value from ZAP on hold
into dd_snap_cmtime instead of updating it.
Expose dd_snap_cmtime as 'snapshots_changed' property that provides a
mechanism to quickly determine whether snapshot list for dataset has
changed without having to mount a dataset or iterate the snapshot list.
It specifies the time at which a snapshot for a dataset was last
created or deleted. This allows us to be more efficient how often we
query snapshots.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13635
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
This also expands the zfs version output from 127 characters to However
Many Are Actually Set
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13330
With the additional benefit of removing all the _all() functions and
treating a NULL list as "all" ‒ the remaining all function is for all
/datasets/, which is consistent with the rest of the API
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13165
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
All it is right now is some #if 0ed Solaris code that returns ENOSYS,
and is only applicable for the Solaris blockdev layer.
In the Illumos gate, there's a single user: rmformat(1);
I recommend a read of the manual as a blast from the past, but, well
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12844Closes#12969
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
This reverts commit f6a0dac84a.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12938
If sufficient memory (<2K, realistically) is available, libzfs_init()
can be significantly shorted by iterating over the correct sysfs
directory before registrations, we can turn 168 stats into 15/18
syscalls (3 opens (6 if built in), 3 fstats, 6 getdentses, and 3
closes), a tenfoldish reduction; this is probably a bit faster, too.
The list is always optional, and registration functions (and one-off
users) can simply pass NULL, which will fall back to the previous
mechanism
Also, don't allocate in zfs_mod_supported_impl, and use use access()
instead of stat(), since existence is really what we care about
Also, fix pre-prop-checking compat in fallback for built-in ZFS
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12089
If the fields to be listed and sorted by are constrained
to those populated by dsl_dataset_fast_stat(), then
zfs list is much faster, as it does not need to open each
objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name
much faster.
However, it was limited to `-o name -s name`, this work
extends this optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties
supported by dsl_dataset_fast_stat() or similar, that do
not require extra locking or reading from disk.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11080
Umer Saleem
Allan Jude
Don Brady
Rob Norris
Alan Somers
George Wilson
Tony Hutter
Ameer Hamza
Brian Behlendorf
Paul Dagnelie
George Amanakis
rob-wing
Tino Reichardt
Richard Yao
Attila Fülöp
George Melikov
Pawel Jakub Dawidek
Ameer Hamza
Mariusz Zaborski
Ryan Moeller
Will Andrews
наб
Jitendra Patidar
Damian Szuberski
Paul Dagnelie