Be sure to invalidate a vdev's cache before performing
a zpool labelclear. There are cases where the cache is
stale because we did some operation that bypassed it,
and since we are doing an open with only O_RDWR, we
should invalidate it to be safe.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6009
Authored by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
- Updated 'zpool labelclear' and 'zdb -l' such that they attempt
to find a vdev given solely its short name. This behavior is
consistent with the upstream OpenZFS code and the test cases
depend on it. The actual implementation differs slightly due
to device naming conventions on Linux.
- auto_online_001_pos, auto_replace_001_pos and add-o_ashift
test cases updated to expect failure when no label exists.
- read_efi_label() and zpool_label_disk_check() are read-only
operations and should use O_RDONLY at open time to enforce this.
- zpool_label_disk() and zpool_relabel_disk() write the partition
information using O_DIRECT an fsync() and page cache invalidation
to ensure a consistent view of the device.
- dump_label() in zdb should invalidate the page cache in order
to get the authoritative label from disk.
OpenZFS-issue: https://www.illumos.org/issues/6865
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c95076cCloses#5981
Allow a pool to be created with both raidz and mirror members,
without giving -f, as long as they have matching redundancy.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5915
df83110 added the ability to specify a custom "ashift" value from the command
line in 'zpool add' and 'zpool attach'. This commit adds additional checks to
the provided ashift to prevent invalid values from being used, which could
result in disastrous consequences for the whole pool.
Additionally provide ASHIFT_MAX and ASHIFT_MIN definitions in spa.h.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5878
When a pool is suspended it's impossible to read the list
of damaged files from disk. This would result in a generic
misleading "insufficient permissions" error message.
Update zpool_get_errlog() to use the standard zpool error
logging functions to generate a useful error message. In
this case:
errors: List of errors unavailable: pool I/O is currently suspended
This patch does not address the related issue of potentially
not being able to resume a suspend pool when the underlying
device names have changed.
Additionally, remove the error handling from zfs_alloc()
in zpool_get_errlog() for readability since this function
can never fail.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4031Closes#5731Closes#5907
- Pass $VDEV_ENC_SYSFS_PATH to 'zpool [iostat|status] -c' to include
enclosure LED sysfs path.
- Set LEDs correctly after import. This includes clearing any erroniously
set LEDs prior to the import, and setting the LED for any UNAVAIL drives.
- Include symlink for vdev_attach-led.sh in Makefile.am.
- Print the VDEV path in all-syslog.sh, and fix it so the pool GUID actually
prints.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5716Closes#5751
Porting notes:
- Many changes were already made in ZoL (for ex. in d4ed66734).
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: George Melikov <mail@gmelikov.ru>
OpenZFS-issue: https://www.illumos.org/issues/6872
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f83b46bCloses#5640
Porting Notes:
- Many of the fixes proposed by this patch were already applied.
In the cases where a different but equivalent fix was made the
code was updated with the OpenZFS version to minimize differences.
- The zpool_get_vdev_by_name() function was previously removed
by commit 235db0a.
Authored by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6551
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b327cd3Closes#5590
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
zpool iostat allows you to specify only certain vdevs to display.
Currently, if you run 'zpool iostat -c CMD vdev1 vdev2 ...'
on specific vdevs, it will actually run the command on *all* vdevs,
and just display the results for the vdevs you specify. This patch
corrects the behavior to only run the command on the specified vdevs,
and also enables the zpool_iostat_005_pos.ksh tests.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5443
Enable picky cstyle checks and resolve the new warnings. The vast
majority of the changes needed were to handle minor issues with
whitespace formatting. This patch contains no functional changes.
Non-whitespace changes are as follows:
* 8 times ; to { } in for/while loop
* fix missing ; in cmd/zed/agents/zfs_diagnosis.c
* comment (confim -> confirm)
* change endline , to ; in cmd/zpool/zpool_main.c
* a number of /* BEGIN CSTYLED */ /* END CSTYLED */ blocks
* /* CSTYLED */ markers
* change == 0 to !
* ulong to unsigned long in module/zfs/dsl_scan.c
* rearrangement of module_param lines in module/zfs/metaslab.c
* add { } block around statement after for_each_online_node
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5465
Do not force VDEV_NAME_TYPE_ID in max_width(), instead add it
in the relevant calls to max_width().
The first location of max_width() where VDEV_NAME_TYPE_ID is
now added in show_import() is followed by print_import_config() and
print_logs(). Both these print children vdev names that have been
retrieved using an explicit VDEV_NAME_TYPE_ID added.
The second location is in status_callback(). This is followed by
print_status_config(), print_logs(), print_l2cache(), and
print_spares(). For l2cache and spares it should not matter as there
are no mirror-X or raidz-X involved. print_status_config() as above
retrieves the name using explicit VDEV_NAME_TYPE_ID before
calling itself to print children.
The call of max_width() in get_namewidth() is not changed, as this is
used by zpool_do_iostat(), followed by print_iostat(), which does not
add VDEV_NAME_TYPE_ID.
Overall, we should consider adding VDEV_NAME_TYPE_ID to the
relevant name_flags / cb_name_flags fields, and remove the explicit
adding in called routines.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5401
This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
First rename spare_cbdata_t cb -> spare_cb in print_status_config(),
to free up cb.
Using the structure removes the explicit parameters namewidth
and name_flags from several functions. Also use status_cbdata_t
for print_import_config(). This simplifies print_logs().
Remove the parameter 'verbose' for print_logs(). It does not really
mean verbose, it selected between the print_status_config and
print_import_config() paths. This selection is now done by
cb_print_config of spare_cbdata_t.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Håkan Johansson <f96hajo@chalmers.se>
Closes#5259
When array is passed as a parameter it degenerates into a
pointer so the sizeof(path) in is_shorthand_path() and always
get return value of 8, instead of the string length we want.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: GeLiXin <ge.lixin@zte.com.cn>
Closes#5198
1.coverity scan CID:147445 function zfs_do_send in zfs_main.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
2.coverity scan CID:147443 function zfs_do_bookmark in zfs_main.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
3.coverity scan CID:147660 function main in zinject.c
Passing string argv[0] of unknown size to strcpy
By the way, the leak of g_zfs is fixed.
4.coverity scan CID: 147442 function make_disks in zpool_vdev.c
Buffer not null terminated (BUFFER_SIZE_WARNING)
5.coverity scan CID: 147661 function main in dir_rd_update.c
passing string cp1 of unknown size to strcpy
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: luozhengzheng <luo.zhengzheng@zte.com.cn>
Closes#5130
This first phase brings over the ZFS SLM module, zfs_mod.c, to handle
auto operations in response to disk events. Disk event monitoring is
provided from libudev and generates the expected payload schema for
zfs_mod. This work leverages the recently added devid and phys_path
strings in the vdev label.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#4673
Commit 519129f added support to multi-thread 'zpool import' for
the case where block devices are scanned for under /dev/. This
commit generalizes that logic and applies it to the case where
device names are acquired from libblkid.
The zpool_find_import_scan() and zpool_find_import_blkid()
functions create an AVL tree containing each device name. Each
entry in this tree is dispatched to a taskq where the function
zpool_open_func() validates the device by opening it and reading
the label. This may result in additional entries being added
to the tree and those device paths being verified.
This is largely how the upstream OpenZFS code behaves but due to
significant differences the non-Linux code has been dropped for
readability. Additionally, this code makes use of taskqs and
kmutexs which are normally not available to the command line tools.
Special care has been taken to allow their use in the import
functions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#4794
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
This is a purely cosmetical change, to consistently prefer one of
two (both acceptable) choises for the word parsable in documentation and
code. I don't really care which to use, but acording to wiktionary
https://en.wiktionary.org/wiki/parsable#English parsable is preferred.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4682
Add argument format to print_one_column(), and use it to call
zfs_nicenum_format with, instead of just zfs_nicenum. Don't print "%"
for fragmentation or capacity percent values.
The calls to print_one_colum is made with ZFS_NICENUM_RAW if
cb->cb_literal (zpool list called with -p), and ZFS_NICENUM_1024 if not.
Also zpool_get_prop is modified to don't add "%" or "x" if literal.
Signed-off-by: Christer Ekholm <che@chrekh.se>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov
Closes#4657
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
5669 altroot not set in zpool create when specified with -o
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/5669
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c423721Closes#4594
6659 nvlist_free(NULL) is a no-op
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: Marcel Telka <marcel@telka.sk>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/6659https://github.com/illumos/illumos-gate/commit/aab83bb
Ported-by: David Quigley <dpquigl@davequigley.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4566
When ZFS partitions a block device it must wait for udev to create
both a device node and all the device symlinks. This process takes
a variable length of time and depends on factors such how many links
must be created, the complexity of the rules, etc. Complicating
the situation further it is not uncommon for udev to create and
then remove a link multiple times while processing the udev rules.
Given the above, the existing scheme of waiting for an expected
partition to appear by name isn't 100% reliable. At this point
udev may still remove and recreate think link resulting in the
kernel modules being unable to open the device.
In order to address this the zpool_label_disk_wait() function
has been updated to use libudev. Until the registered system
device acknowledges that it in fully initialized the function
will wait. Once fully initialized all device links are checked
and allowed to settle for 50ms. This makes it far more likely
that all the device nodes will exist when the kernel modules
need to open them.
For systems without libudev an alternate zpool_label_disk_wait()
was updated to include a settle time. In addition, the kernel
modules were updated to include retry logic for this ENOENT case.
Due to the improved checks in the utilities it is unlikely this
logic will be invoked. However, if the rare event it is needed
it will prevent a failure.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4523Closes#3708Closes#4077Closes#4144Closes#4214Closes#4517
When partitioning a device a name may be specified for each partition.
Internally zfs doesn't use this partition name for anything so it
has always just been set to "zfs".
However this isn't optimal because udev will create symlinks using
this name in /dev/disk/by-partlabel/. If the name isn't unique
then all the links cannot be created.
Therefore a random 64-bit value has been added to the partition
label, i.e "zfs-1234567890abcdef". Additional information could
be encoded here but since partitions may be reused that might
result in confusion and it was decided against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#4517
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
This issue was caused by calling `thread_init()` and `thread_fini()`
multiple times resulting in `kthread_key` being invalid. To resolve
the issue the explicit calls to `thread_init()` and `thread_fini()`
required by the `zpool` command have been moved in to the command.
Consumers such as `zdb` and `zhack` perform the same initialized
through `kernel_init()` and `kernel_fini()`.
Resolving this issue allows multiple additional test cases to
be enabled.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#4331
When checking a whole disk to see if it can be safely added to
the pool a variety of checks are done. One of those checks is
to attempt to determine the partition information and scan all
the partitions for existing filesystems.
Since ZoL contains a EFI library this partition scanning is
easy to do for GPT partitioned disks. However, for non-GPT
partitioned disks (MBR/EBR) things are a bit harder. The lack of
a convenient library means non-GPT partitioned disks will not
have all their partitions checked. For this reason, the default
behavior was to require the force option. For example:
invalid vdev specification
use '-f' to override the following errors:
/dev/vdb does not contain an GPT label but it may contain partition
information in the MBR.
However in practice requiring the force option for this case is
counter-intuitively less safe. The reason is because only the first
error is returned. By passing the force option it will suppress
this first warning and potentially others you were not aware of.
Therefore this patch inverts the default behavior for non-GPT
formated disks (unformatted, MBR/EBR, etc). If no GPT table is
detected and there is no file system detected on the provided
block device. Then it will be assumed that block device is safe
to use.
Longer term it would be nice to see MBR/EBR scanning added to
the utilities. This should be fairly straight forward to do.
However these days it's somewhat less critical because Linux
defaults to GPT partition tables for devices 2TB or larger.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2660Closes#2274
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4368
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
5767 fix several problems with zfs test suite
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/5767https://github.com/illumos/illumos-gate/commit/52244c0
Porting Notes:
- Only the updates to zpool_main.c were kept because the ZFS test
suite is not currently part of the ZoL source tree. The test
suite itself should be updated to include the latest versions
of the tests once we're running it for every commit
- Fixes `zpool list` output.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
5959 clean up per-dataset feature count code
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed by: George Wilson <george@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/5959https://github.com/illumos/illumos-gate/commit/ca0cc39
Porting notes:
illumos code doesn't check for feature_get_refcount() returning
ENOTSUP (which means feature is disabled) in zdb. zfsonlinux added
a check in https://github.com/zfsonlinux/zfs/commit/784652c
due to #3468. The check was reintroduced here.
Ported-by: Witaut Bajaryn <vitaut.bayaryn@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3965
All other sections use a tab, which makes them easy to parse. Only the
"scan:" section had its continuation lines indented with four spaces.
This makes them consistent with the others.
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#3769
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
5118 When verifying or creating a storage pool, error messages
only show one device
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Boris Protopopov <boris.protopopov@me.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://github.com/illumos/illumos-gate/commit/75fbdf9https://www.illumos.org/issues/5118
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3567
4966 zpool list iterator does not update output
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://github.com/illumos/illumos-gate/commit/cd67d23https://www.illumos.org/issues/4966
Ported-by: kernelOfTruth kerneloftruth@gmail.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3566
sysstat's iostat omits the first report when the -y option is used.
This patch adds that functionality and omits the first report with
statistics since system boot.
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3439
All fprintf() error messages are moved out of the libzfs_init()
library function where they never belonged in the first place. A
libzfs_error_init() function is added to provide useful error
messages for the most common causes of failure.
Additionally, in libzfs_run_process() the 'rc' variable was renamed
to 'error' for consistency with the rest of the code base.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Support exporting all imported pools in one go, using 'zpool export -a'.
This is accomplished by moving the export parts from zpool_do_export()
in to the new function zpool_export_one(). The for_each_pool() function
is used to enumerate the list of pools to be exported. Passing an argc
of 0 implies the function should be called on all pools.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #3203
5134 if ZFS_DEBUG or debug= is set, libzpool should enable debug prints
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Saso Kiselkov <skiselkov.ml@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/projects/illumos-gate/issues/5134https://github.com/illumos/illumos-gate/commit/7fa49ea
Porting notes:
Added dprintf_setup() to main in zfs_main.c and zpool_main.c.
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2669
The newroot nvlist should be freed before returning.
Signed-off-by: Isaac Huang <he.huang@intel.com>
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3264
When using 'zpool import' to scan for available pools prefer vdev names
which reference vdevs with more valid labels. There should be two labels
at the start of the device and two labels at the end of the device. If
labels are missing then the device has been damaged or is in some other
way incomplete. Preferring names with fully intact labels helps weed out
bad paths and improves the likelihood of being able to import the pool.
This behavior only applies when scanning /dev/ for valid pools. If a
cache file exists the pools described by the cache file will be used.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Closes#3145Closes#2844Closes#3107
In dry run mode, zpool should display more of the proposed pool
configuration for "zpool add". This commit adds support for displaying
cache devices.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1106
If spl_hostid is set via module parameter, it's likely different from
gethostid(). Therefore, the userspace tool should read it first before
falling back to gethostid().
Signed-off-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3034
Commit c66989b accidentally introduced a cstyle issue which went
unnoticed. This tiny patch corrects that oversight.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In userland we need to switch over to the temporary name once the
pool has been created, otherwise the root dataset won't mount
and the error "cannot open 'the_real_name': dataset does not exist"
is printed.
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2760
Change the zpool program to skip its hostid mismatch check in the
same way that libzfs already does.
Invoked imports fail if the ZPOOL_CONFIG_HOSTID nvpair is missing in
the /etc/zfs/zpool.cache file, which can happen as of the /etc/hostid
deprecation in commit zfsonlinux/spl@acf0ade362.
Signed-off-by: Darik Horn <dajhorn@vanadac.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2794
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
zpool import's -t parameter is intended for use with -R when operating
on pools that belong to other systems. Like -R, pools imported in this
way should not update the cachefile unless explicitly requested. The
initial implementation allowed the cachefile to be updated when -R was
not used. This went uncaught during testing because -R had implicitly
disabled use of the cachefile.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
Adding to a property list only if there is no existing value is used
twice. Once by zpool create -R and again by zpool import -R. Now that
zpool create -t and zpool import -t also need it, lets refactor it into
a helper function to make the code more readable.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
The 'zpool list -v' command displays lots of info but excludes the
capacity of each disk. This should be added.
5147 zpool list -v should show individual disk capacity
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Matthew Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/5147https://github.com/illumos/illumos-gate/commit/7a09f97
Ported by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2688
Change mount code to diagnose filesystem versions that
are not supported by the current implementation.
Change upgrade code to do likewise and refuse to upgrade
a pool if any filesystems on it are a version which is
not supported by the current implementation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Closes: #2616
4970 need controls on i/o issued by zpool import -XF
4971 zpool import -T should accept hex values
4972 zpool import -T implies extreme rewind, and thus a scrub
4973 spa_load_retry retries the same txg
4974 spa_load_verify() reads all data twice
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
https://www.illumos.org/issues/4970https://www.illumos.org/issues/4971https://www.illumos.org/issues/4972https://www.illumos.org/issues/4973https://www.illumos.org/issues/4974https://github.com/illumos/illumos-gate/commit/e42d205
Notes:
This set of patches adds a set of tunable parameters for the
"extreme rewind" mode of pool import which allows control over
the traversal performed during such an import.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2598
The Intel DC S3500 and Intel DC S3700 are optimized to handle 4KB
sectors well despite of their 8KB page sizes, so we move them to a new
category for enterprise drives where they will receive ashift=12. They
are joined by the Intel 730 series, which uses the same disk controller,
as well as a San Disk enterprise drive. The drive IDs for these two were
obtained by myself with the drive_id utility. The drive ID for the 240GB
Intel 730 model was extrapolated from the drive ID for the 480GB model.
Lastly, we also add some Western Digital mobile drives. ryuo in
\#zfsonlinux on freenode obtained "ATA WDC WD2500BEVT-0" from
running drive_id on his own hardware. The additional drives in that
family were extrapolated from that identifer.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2601
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
4374 dn_free_ranges should use range_tree_t
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4374https://github.com/illumos/illumos-gate/commit/bf16b11
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2531
4171 clean up spa_feature_*() interfaces
4172 implement extensible_dataset feature for use by other zpool features
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Garrett D'Amore <garrett@damore.org>a
References:
https://www.illumos.org/issues/4171https://www.illumos.org/issues/4172https://github.com/illumos/illumos-gate/commit/2acef22
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2528
This functionality is already available in 'zfs get'. Providing
it for 'zpool get' is useful and good for consistency.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #2522
Users need to be aware that when replacing devices in an existing
pool they may need to override automatically detected ashift value.
This will all depend on the exact hardware they are using.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2024
Verbatim imports can cause hostid mismatches, but things otherwise work. `zpool
status` does not handle this and will fail when assertions are enabled:
```
zpool: ../../cmd/zpool/zpool_main.c:4418: status_callback: Assertion `reason == ZPOOL_STATUS_OK' failed.
Program received signal SIGABRT, Aborted.
```
Lets instead add a case to display an informative message such as this:
```
pool: rpool
state: ONLINE
status: Mismatch between pool hostid and system hostid on imported pool.
This pool was previously imported into a system with a different hostid,
and then was verbatim imported into this system.
action: Export this pool on all systems on which it is imported.
Then import it to correct the mismatch.
see: http://zfsonlinux.org/msg/ZFS-8000-EY
scan: scrub repaired 0 in 0h8m with 0 errors on Thu Apr 17 19:43:57 2014
config:
NAME STATE READ WRITE CKSUM
rpool ONLINE 0 0 0
sda ONLINE 0 0 0
errors: No known data errors
```
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2342
zfsonlinux/zfs@1db7b9be75 should have
fixed this, but this particular string was overlooked.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2288
This functionality has always been missing. But until now there
were no zevents which included an array of strings so it wasn't
missed. However, that's now changed so to ensure this information
is output correctly by 'zpool events -v' the DATA_TYPE_STRING_ARRAY
has been implemented.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
zpool_events_next() can be called in blocking mode by specifying a
non-zero value for the "block" parameter. However, the design of
the ZFS Event Daemon (zed) requires additional functionality from
zpool_events_next(). Instead of adding additional arguments to the
function, it makes more sense to use flags that can be bitwise-or'd
together.
This commit replaces the zpool_events_next() int "block" parameter with
an unsigned bitwise "flags" parameter. It also defines ZEVENT_NONE
to specify the default behavior. Since non-blocking mode can be
specified with the existing ZEVENT_NONBLOCK flag, the default behavior
becomes blocking mode. This, in effect, inverts the previous use
of the "block" parameter. Existing callers of zpool_events_next()
have been modified to check for the ZEVENT_NONBLOCK flag.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2
Due to the very poorly chosen argument name 'cleanup_fd' it was
completely unclear that this file descriptor is used to track the
current cursor location. When the file descriptor is created by
opening ZFS_DEV a private cursor is created in the kernel for the
returned file descriptor. Subsequent calls to zpool_events_next()
and zpool_events_seek() then require the file descriptor as an
argument to reposition the cursor. When the file descriptor is
closed the kernel state tracking the cursor is destroyed.
This patch contains no functional change, it just changes a
few variable names and clarifies the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Issue #2
Originally, users had to handle spa namespace collisions by either
exporting the already imported pool or by specifying a new name for the
pool with a conflicting name. In the case of root pools from virtual
guests, neither approach to collision resolution is reasonable. This is
addressed by extending the new name syntax with a -t option to specify
that the new name is temporary. When specified, this sets an internal
flag that is passed into the kernel to tell it that all label updates
should refer to the name used in the original label. Consequently, the
original pool name will be retained on export.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2189
ZoL commit 1421c89 unintentionally changed the disk format in a forward-
compatible, but not backward compatible way. This was accomplished by
adding an entry to zbookmark_t, which is included in a couple of
on-disk structures. That lead to the creation of pools with incorrect
dsl_scan_phys_t objects that could only be imported by versions of ZoL
containing that commit. Such pools cannot be imported by other versions
of ZFS or past versions of ZoL.
The additional field has been removed by the previous commit. However,
affected pools must be imported and scrubbed using a version of ZoL with
this commit applied. This will return the pools to a state in which they
may be imported by other implementations.
The 'zpool import' or 'zpool status' command can be used to determine if
a pool is impacted. A message similar to one of the following means your
pool must be scrubbed to restore compatibility.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #1 detected.
action: The pool can be imported using its name or numeric identifier,
however there is a compatibility issue which should be corrected
by running 'zpool scrub'
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
$ zpool status
pool: zol-0.6.2-173
state: ONLINE
scan: pool compatibility issue detected.
see: https://github.com/zfsonlinux/zfs/issues/2094
action: To correct the issue run 'zpool scrub'.
config:
...
If there was an async destroy in progress 'zpool import' will prevent
the pool from being imported. Further advice on how to proceed will be
provided by the error message as follows.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #2 detected.
action: The pool can not be imported with this version of ZFS due to an
active asynchronous destroy. Revert to an earlier version and
allow the destroy to complete before updating.
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
Pools affected by the damaged dsl_scan_phys_t can be detected prior to
an upgrade by running the following command as root:
zdb -dddd poolname 1 | grep -P '^\t\tscan = ' | sed -e 's;scan = ;;' | wc -w
Note that `poolname` must be replaced with the name of the pool you wish
to check. A value of 25 indicates the dsl_scan_phys_t has been damaged.
A value of 24 indicates that the dsl_scan_phys_t is normal. A value of 0
indicates that there has never been a scrub run on the pool.
The regression caused by the change to zbookmark_t never made it into a
tagged release, Gentoo backports, Ubuntu, Debian, Fedora, or EPEL
stable respositorys. Only those using the HEAD version directly from
Github after the 0.6.2 but before the 0.6.3 tag are affected.
This patch does have one limitation that should be mentioned. It will not
detect errata #2 on a pool unless errata #1 is also present. It expected
this will not be a significant problem because pools impacted by errata #2
have a high probably of being impacted by errata #1.
End users can ensure they do no hit this unlikely case by waiting for all
asynchronous destroy operations to complete before updating ZoL. The
presence of any background destroys on any imported pools can be checked
by running `zpool get freeing` as root. This will display a non-zero
value for any pool with an active asynchronous destroy.
Lastly, it is expected that no user data has been lost as a result of
this erratum.
Original-patch-by: Tim Chase <tim@chase2k.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2094
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
Both the zpool_import_status() and zpool_get_status() functions
return the zpool_status_t enum. This explicit type should be used
rather than the more generic int type.
This patch makes no functional change and should only be considered
code cleanup. It happens to have been done in the context of #2094
because that's when I noticed this issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
31fc19399e incorrectly removed $(LIBBLKID)
from cmd/zpool/Makefile.am. This meant that the toolchain was not given
-lblkid, which resulted in the following build failure on Ubuntu 13.10:
/usr/bin/ld: zpool_vdev.o: undefined reference to symbol
'blkid_put_cache@@BLKID_1.0'
/lib/x86_64-linux-gnu/libblkid.so.1: error adding symbols: DSO missing
from command line
collect2: error: ld returned 1 exit status
That commit reworked various Makefile.am to follow best practices, so we
reintroduce $(LIBBLKID) in a manner consistent with that, rather than
explicitly reverting the change.
Reproduction of this issue was done on a Gentoo Linux system by
executing the following commands:
zfs create -o mountpoint=/mnt/ubuntu-13.10 rpool/ROOT/ubuntu-13.10
debootstrap --variant=buildd --arch amd64 saucy /mnt/ubuntu-13.10 http://archive.ubuntu.com/ubuntu/
mount -o bind /dev /mnt/ubuntu-13.10/dev/
mount -o bind /proc/ /mnt/ubuntu-13.10/proc/
mount -o bind /sys/ /mnt/ubuntu-13.10/sys/
cp /etc/resolv.conf /mnt/ubuntu-13.10/etc/
(cd /mnt/ubuntu-13.10/root/ && git clone git://github.com/zfsonlinux/zfs.git)
chroot /mnt/ubuntu-13.10/
apt-get install git autoconf libtool zlib1g-dev uuid-dev libblkid-dev
\#apt-get install alien fakeroot vim
cd /root/zfs
./autogen.sh
./configure --with-config=user --prefix=/usr
make
That will create a Ubuntu 13.10 chroot, fetch the sources and build
test. At this point, cmd/zpool/Makefile.am was modified and the
following commands were run to verify that the build issue was resolved:
git clean -xdf
./autogen.sh
./configure --with-config=user --prefix=/usr
make
Although it is not shown here, the absence of libblkid-dev enables ZFS
to build successfully without the patch. This could explain how this
escaped detection until recently. A test without libblkid-dev was done
to verify that the patch did not cause a regression in the absence of
libblkid:
apt-get remove libblkid-dev
git clean -xdf
./autogen.sh
./configure --with-config=user --prefix=/usr
make
Additionally, the commands themselves were tested against my live system
from within the chroot to ensure basic functionality. My live system had
corresponding kernel modules already installed and basic commands such
as `zpool list` and `zfs list` worked without incident. Lastly, this
patch was also build tested on Gentoo Linux, where it caused no
problems.
At time of writing, these steps can be used to reproduce these results
on any modern Linux system that has debootstrap installed. On Gentoo,
installing debootstrap can be done with `emerge dev-util/debootstrap`.
The current ZFSOnLinux HEAD revision as of writing is
fd23720ae1. Once this is fixed in HEAD,
either that revision or another before this fix and after
31fc19399e will be needed to reproduce
this issue.
Lastly, it remains to be seen why the toolchains on the systems
performing regression tests did not catch this. This is not a
ZFS-specific issue, but it is something that we will want to explore in
the future.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2038
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
Added:
Adata S396 (obtained from drive_id)
Apple MacBookAir3,1 SSD (obtained from drive_id)
Apple MacBookPro10,1 SSD (obtained from drive_id)
Intel 510 (obtained from drive_id)
Intel 710 (obtained from drive_id)
Intel DC S3500 (obtained from drive_id)
Netapp LUN (obtained from illumos user's sd.conf)
OCZ Agility 3 (obtained from drive_id)
OCZ Vertex (obtained from drive_id)
Samsung PM800 (obtained from drive_id)
Sandisk U100 (obtained from drive_id)
Sun Comstar (obtained from illumos user's sd.conf)
Notes:
1. The entries for the Intel DC S3500 were extrapolated from the 800GB
model's entry, which is "ATA INTEL SSDSC2BB80".
2. The entires for the Intel 710 were extrapolated from the 120GG
model's entry, which is "ATA INTEL SSDSA2BZ12".
3. The entires for the Intel 510 were extrapolated from the 250GB
model's entry, which is "ATA INTEL SSDSC2MH25".
4. The entires for the Apple MacBookPro10,1 SSD were extrapolated from
the 512GB model's entry, which is "ATA APPLE SSD SM512E". Google
searches suggest that this is a rebadged Samsung 830.
5. The entires for the Apple MacBookAir3,1 SSD were extrapolated from
the 128GB model's entry, which is "ATA APPLE SSD TS128C". Google
searches suggest that this is a rebadged Kingston SSDNow V+ 100 (based
on Toshiba).
6. Sun Comstar is an iSCSI Target, so we cannot tell what the correct
sector size is through this method. We list it only for reference
purposes, but it is commented out. Similarly, it is not clear what the
right thing to do for Netapp is, so we comment it out.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1907
On some platforms symbols provided by libzfs_core and used by
libzfs were not available to the linker. To avoid this issue
libzfs_core has been added to the list of required libraries
when building utilities which depend on libzfs. This should
have been handled properly by libtool and it's still not
entirely clear why it wasn't on all platforms.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1841
3745 zpool create should treat -O mountpoint and -m the same
3811 zpool create -o altroot=/xyz -O mountpoint=/mnt ignores
the mountpoint option
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3745https://www.illumos.org/issues/3811illumos/illumos-gate@8b71377531
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
This works the same as the -p switch to "zfs get", displaying full
resolution values for appropriate attributes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1813
When creating a new pool, or adding/replacing a disk in an existing
pool, partition tables will be automatically created on the devices.
Under normal circumstances it will take less than a second for udev
to create the expected device files under /dev/. However, it has
been observed that if the system is doing heavy IO concurrently udev
may take far longer. If you also throw in some cheap dodgy hardware
it may take even longer.
To prevent zpool commands from failing due to this the default wait
time for udev is being increased to 30 seconds. This will have no
impact on normal usage, the increase timeout should only be noticed
if your udev rules are incorrectly configured.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1646
Document the "-D" and "-T" options and the optional interval
and count or "zpool status".
Also for zpool's man page, use a consistent order for the
various "-T" options to match the program's help output.
Document the effect of additional "-D" options for zdb.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1786
Libraries that depend on other libraries should list them in ELF's
DT_NEEDED field so that programs linking to them do not need to specify
those libraries unless they depend on them as well. This is not the case
in the current code and the consequence is that anything that needs a
library must know its dependencies. This is fragile and caused GRUB2's
configure script to break when a dependency was added on libblkid in
libzfs.
This resolves that problem by using LIBADD/LDADD to specify libraries in
Makefile.am instead of LDFLAGS. This ensures that proper DT_NEEDED
entries are generated and prevents GRUB2's configure script from
breaking in the presence of a libblkid dependency. This also removes
unneeded dependencies from various files.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1751
Add Corsair Force GS drive (obtained from drive_id)
Add Kingston HyperX 3K (obtained from drive_id)
Add OCZ Vertex 4 drive (obtained from drive_id)
Add Samsung SM843T enterprise drive (obtained from drive_id)
Add entries for additional sizes of Intel 320/330/335/520 series
Add Cruical C400 (obtained from Illumos user's sd.conf)
Add Toshiba SSD (obtained from Illumos user's sd.conf)
Add Samsung's first SLC SSD (obtained from drive_id)
Add OCZ Core Series (obtained from drive_id)
Add Intel DC S3700 (obtained from drive_id)
Notes:
1. The drive identifer obtained for the Samsung SM843T was MZ7WD480. The
rest were extrapolated. The additional entries were checked with Google
to verify that such drives exist in the wild.
2. The additional entries for Intel drives were extrapolated from
existing entries. The additional entries were checked with Google to
verify that such drives exist in the wild.
3. The "ATA C400-MTFDDAC512M" and "ATA TOSHIBA THNSNH51" entries
are from the sd.conf of gcbirzan on freenode. Additional entries were
extrapolated from them and checked with Google.
4. I obtained the Samsung MCCOE64G entry from an actual drive. The
Samsung MCCOE32G entry was extrapolated from it and checked with
Google.
5. I obtained the SSDSC2BA10 from a 100GB Intel DC S3700 drive and
extrapolated the entries for the additional models.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1752
Giuseppe Di Natale
Yuri Pankov
Håkan Johansson
LOLi
Brian Behlendorf
Tony Hutter
George Melikov
ka7
cao
luozhengzheng
GeLiXin
liuhuang
Don Brady
Gvozden Neskovic
Colin Ian King
Christer Ekholm
Adam Stevko
Josef 'Jeff' Sipek
Richard Yao
John Wren Kennedy
Matthew Ahrens
Remy Blank
Turbo Fredriksson
Prasad Joshi
Basil Crow
George Wilson
Hajo Möller
Isaac Huang
Tim Chase
Chunwei Chen
Jacek Fefliński
ilovezfs
Darik Horn
Dan Swartzendruber
John Albietz
Chris Dunlap
Michael Kjorling
Maximilian Mehnert
Will Andrews
Ralf Ertzinger