Currently, when attempting to list snapshots ZFS may do a lot of
extra work checking child datasets. This is because the code does
not realize that it will not be able to reach any snapshots
contained within snapshots that are at the depth limit since the
snapshots of those datasets are counted as an additional layer
deeper. This patch corrects this issue.
In addition, this patch adds the ability to do perform the commands:
$ zfs list -t snapshot <dataset>
$ zfs get -t snapshot <prop> <dataset>
as a convenient way to list out properties of all snapshots of a
given dataset without having to use the depth limit.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8539
UNMAP/TRIM support is a frequently-requested feature to help
prevent performance from degrading on SSDs and on various other
SAN-like storage back-ends. By issuing UNMAP/TRIM commands for
sectors which are no longer allocated the underlying device can
often more efficiently manage itself.
This TRIM implementation is modeled on the `zpool initialize`
feature which writes a pattern to all unallocated space in the
pool. The new `zpool trim` command uses the same vdev_xlate()
code to calculate what sectors are unallocated, the same per-
vdev TRIM thread model and locking, and the same basic CLI for
a consistent user experience. The core difference is that
instead of writing a pattern it will issue UNMAP/TRIM commands
for those extents.
The zio pipeline was updated to accommodate this by adding a new
ZIO_TYPE_TRIM type and associated spa taskq. This new type makes
is straight forward to add the platform specific TRIM/UNMAP calls
to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are
handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs.
This makes it possible to largely avoid changing the pipieline,
one exception is that TRIM zio's may exceed the 16M block size
limit since they contain no data.
In addition to the manual `zpool trim` command, a background
automatic TRIM was added and is controlled by the 'autotrim'
property. It relies on the exact same infrastructure as the
manual TRIM. However, instead of relying on the extents in a
metaslab's ms_allocatable range tree, a ms_trim tree is kept
per metaslab. When 'autotrim=on', ranges added back to the
ms_allocatable tree are also added to the ms_free tree. The
ms_free tree is then periodically consumed by an autotrim
thread which systematically walks a top level vdev's metaslabs.
Since the automatic TRIM will skip ranges it considers too small
there is value in occasionally running a full `zpool trim`. This
may occur when the freed blocks are small and not enough time
was allowed to aggregate them. An automatic TRIM and a manual
`zpool trim` may be run concurrently, in which case the automatic
TRIM will yield to the manual TRIM.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Contributions-by: Tim Chase <tim@chase2k.com>
Contributions-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8419Closes#598
When Multihost is enabled, and a pool is imported, uberblock writes
include ub_mmp_delay to allow an importing node to calculate the
duration of an activity test. This value, is not enough information.
If zfs_multihost_fail_intervals > 0 on the node with the pool imported,
the safe minimum duration of the activity test is well defined, but does
not depend on ub_mmp_delay:
zfs_multihost_fail_intervals * zfs_multihost_interval
and if zfs_multihost_fail_intervals == 0 on that node, there is no such
well defined safe duration, but the importing host cannot tell whether
mmp_delay is high due to I/O delays, or due to a very large
zfs_multihost_interval setting on the host which last imported the pool.
As a result, it may use a far longer period for the activity test than
is necessary.
This patch renames ub_mmp_sequence to ub_mmp_config and uses it to
record the zfs_multihost_interval and zfs_multihost_fail_intervals
values, as well as the mmp sequence. This allows a shorter activity
test duration to be calculated by the importing host in most situations.
These values are also added to the multihost_history kstat records.
It calculates the activity test duration differently depending on
whether the new fields are present or not; for importing pools with
only ub_mmp_delay, it uses
(zfs_multihost_interval + ub_mmp_delay) * zfs_multihost_import_intervals
Which results in an activity test duration less sensitive to the leaf
count.
In addition, it makes a few other improvements:
* It updates the "sequence" part of ub_mmp_config when MMP writes
in between syncs occur. This allows an importing host to detect MMP
on the remote host sooner, when the pool is idle, as it is not limited
to the granularity of ub_timestamp (1 second).
* It issues writes immediately when zfs_multihost_interval is changed
so remote hosts see the updated value as soon as possible.
* It fixes a bug where setting zfs_multihost_fail_intervals = 1 results
in immediate pool suspension.
* Update tests to verify activity check duration is based on recorded
tunable values, not tunable values on importing host.
* Update tests to verify the expected number of uberblocks have valid
MMP fields - fail_intervals, mmp_interval, mmp_seq (sequence number),
that sequence number is incrementing, and that uberblock values match
tunable settings.
Reviewed-by: Andreas Dilger <andreas.dilger@whamcloud.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7842
1) As implemented the `zpool labelclear` command overwrites
the calculated offsets of all four vdev labels even when only a
single valid label is found. If the device as been re-purposed
but still contains a valid label this can result in space no
longer owned by ZFS being zeroed. Prevent this by verifying
every label removed is intact before it's overwritten.
2) Address a small bug in zpool_do_labelclear() which prevented
labelclear from working on file vdevs. Only block devices support
BLKFLSBUF, try the ioctl() but when it's reported as unsupported
this should not be fatal.
3) Fix `zpool labelclear` so it can be run on vdevs which were
removed from the pool with `zpool remove`. Additionally, allow
intact but partial labels to be cleared as in the case of a failed
`zpool attach` or `zpool replace`.
4) Remove LABELCLEAR and LABELREAD variables for test cases.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8500Closes#8373Closes#6261
Currently, there is an issue in the sequential scrub code which
prevents self healing from working in some cases. The scrub code
will split up all DVA copies of a bp and issue each of them
separately. The problem is that, since each of the DVAs is no
longer associated with the others, the self healing code doesn't
have the opportunity to repair problems that show up in one of the
DVAs with the data from the others.
This patch fixes this issue by ensuring that all IOs issued by the
sequential scrub code include all DVAs. Initially, only the first
DVA of each is attempted. If an issue arises, the IO is retried
with all available copies, giving the self healing code a chance
to correct the issue.
To test this change, this patch also adds the ability for zinject
to specify individual DVAs to inject read errors into. We then
add a new test case that utilizes this functionality to ensure
scrubs and self-healing reads can handle and transparently fix
issues with individual copies of blocks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8453
This patch attempts to address some user concerns that have arisen
since errata 4 was introduced.
* The errata warning has been made less scary for users without
any encrypted datasets.
* The errata warning now clears itself without a pool reimport if
the bookmark_v2 feature is enabled and no encrypted datasets
exist.
* It is no longer possible to create new encrypted datasets without
enabling the bookmark_v2 feature, thus helping to ensure that the
errata is resolved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue ##8308
Closes#8504
Update zed.rc values reflect their default value. This helps
avoid confusion if a user expects functionality to be enabled.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Kash Pande <kash@tripleback.net>
Closes#8498
Currently, the verbose output of zstreamdump includes new line
characters within some individual records. Presumably, this was
originally done to keep the output from getting too wide to fit
on a terminal. However, since new flags and struct members have
been added, these rules have not been maintained consistently. In
addition, these newlines can make it hard to grep the output in
some scenarios. This patch simply removes these newlines, making
the output easier to grep and removing the inconsistency.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8493
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
This is a simple fix for a typo ("perfetch" rather than "prefetch")
in arc_summary3.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Jason Cohen <jwittlincohen@gmail.com>
Closes#8499
This patch modifies the zfs_ioc_snapshot_list_next() ioctl to enable it
to take input parameters that alter the way looping through the list of
snapshots is performed. The idea here is to restrict functions that
throw away some of the snapshots returned by the ioctl to a range of
snapshots that these functions actually use. This improves efficiency
and execution speed for some rollback and send operations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8077
When multihost is enabled, and a pool is suspended, return
EINVAL in response to "zpool clear <pool>". The pool
may have been imported on another host while I/O was suspended.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#6933Closes#8460
When feeding a replication stream to `zstreamdump -d` (raw dump mode),
it does not print the raw data for DRR_WRITE_EMBEDDED records.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#8430
The "-t" argument to "zfs program" specifies a limit on the number of
LUA instructions that can be executed. The zfs.8 manpage has the wrong
description. It should be updated to match what's in zfs-program.8
Also fix the formatting of the zfs help message.
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8410
Add -h switch to zfs send command to send dataset holds. If
holds are present in the stream, zfs receive will create them
on the target dataset, unless the zfs receive -h option is used
to skip receive of holds.
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#7513
with builds on illumos based platform we can see build issue
because label_t has been redefined.
for reduce build issues on others platforms we should rename
label_t to zdb_label_t.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#8397
Initially, metaslabs and space maps used to be the same thing
in ZFS. Later, we started differentiating them by referring
to the space map as the on-disk state of the metaslab, making
the metaslab a higher-level concept that is metadata that deals
with space accounting. Today we've managed to split that code
furthermore, with the space map being its own on-disk data
structure used in areas of ZFS besides metaslabs (e.g. the
vdev-wide space maps used for zpool checkpoint or vdev removal
features).
This patch refactors the space map code to further split the
space map code from the metaslab code. It does so by getting
rid of the idea that the space map can have a different in-core
and on-disk length (sm_length vs smp_length) which is something
that is only used for the metaslab code, and other consumers
of space maps just have to deal with. Instead, this patch
introduces changes that move the old in-core length of the
metaslab's space map to the metaslab structure itself (see
ms_synced_length field) while making the space map code only
care about the actual space map's length on-disk.
The result of this is that space map consumers no longer have
to deal with syncing two different lengths for the same
structure (e.g. space_map_update() goes away) while metaslab
specific behavior stays within the metaslab code. Specifically,
the ms_synced_length field keeps track of the amount of data
metaslab_load() can read from the metaslab's space map while
working concurrently with metaslab_sync() that may be
appending to that same space map.
As a side note, the patch also adds a few comments around
the metaslab code documenting some assumptions and expected
behavior.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8328
note: which is non-standard. Use builtin 'command -v' instead. [SC2230]
note: Use -n instead of ! -z. [SC2236]
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#8367
The zpool iostat latency histograms (-w) has column names
'sync_queue' and 'async_queue', which do not match the man page, nor
the equivalent columns in average latency. Change the column
names to be 'syncq_wait' and 'asyncq_wait' to be consistent.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8338
Currently the point of -L option in zdb is to disable leak
tracing and the loading of space maps because they are expensive,
yet still do leak detection in terms of space. Unfortunately,
there is a scenario where this is a lie. If we are using zdb -L
on a pool where a vdev is being removed, zdb_claim_removing()
will open the metaslab space maps of that device.
This patch makes it so zdb -L skips leak detection altogether
and ensures that no space maps are loaded.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8335
GCC 9.0 is complaining because we're trying to print strings that
are defined like this:
.zo_pool = { 'z', 't', 'e', 's', 't', '\0' },
Fix them by making them actual strings.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8330
The range_tree_verify function looks for a segment in a
range tree and panics if the segment is present on the
tree. This patch gives the function a more descriptive
name.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8327
If you try to get the userspace, groupspace or projectspace on a ZVOL,
the generated error results in passing EINVAL to
zfs_standard_error_fmt() when we should return a specific error to
inform the user that those properties aren't available on volumes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8279
When `zpool iostat` fills the terminal the headers should be
printed again. `zpool iostat -n` can be used to suppress this.
If the command is not attached to a tty, headers will not be
printed so as to not break existing scripts.
Reviewed-by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8235Closes#8262
Most callers that need to operate on a loaded metaslab, always
call metaslab_load_wait() before loading the metaslab just in
case someone else is already doing the work.
Factoring metaslab_load_wait() within metaslab_load() makes the
later more robust, as callers won't have to do the load-wait
check explicitly every time they need to load a metaslab.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#8290
By design ztest will never inject non-repairable damage in to the
pool. Update the ztest_scrub() test case such that it waits for
the scrub to complete and verifies the pool is always repairable.
After enabling scrub verification two scenarios were encountered
which are the result of how ztest manages failure injection.
The first case is straight forward and pertains to detaching a
mirror vdev. In this case, the pool must always be scrubbed prior
the detach. Failure to do so can potentially lock in previously
repairable data corruption by removing all good copies of a block
leaving only damaged ones.
The second is a little more subtle. The child/offset selection
logic in ztest_fault_inject() depends on the calculated number of
leaves always remaining constant between injection passes. This
is true within a single execution of ztest, but when using zloop.sh
random values are selected for each restart. Therefore, when ztest
imports an existing pool it must be scrubbed before failure injection
can be safely enabled. Otherwise it is possible that it will inject
non-repairable damage.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8269
Currently, the functions dbuf_prefetch_indirect_done() and
dmu_assign_arcbuf_by_dnode() assume that dbuf_hold_level() cannot
fail. In the event of an error the former will cause a NULL pointer
dereference and the later will trigger a VERIFY. This patch adds
error handling to these functions and their callers where necessary.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8291
The ztest_ddt_repair() test is designed inflict damage to the
ddt which can be repairable by a scrub. Unfortunately, this
repair logic was broken at some point and it went undetected.
This issue is not specific to ztest, but thankfully this extra
redundancy is rarely enabled and even more rarely needed.
The root cause was identified to be the ddt_bp_create()
function called by dsl_scan_ddt_entry() which did not set the
dedup bit of the generated block pointer.
The consequence of this was that the ZIO_DDT_READ_PIPELINE was
never enabled for the block pointer during the scrub, and the
dedup ditto repair logic was never run. Note that for demand
reads which don't rely on ddt_bp_create() the required pipeline
stages would be enabled and the repair performed.
This was resolved by unconditionally setting the dedup bit in
ddt_bp_create(). This way all codes paths which may need to
perform a repair from a block pointer generated from the dtt
entry will be able too. The only exception is that the dedup
bit is cleared in ddt_phys_free() which is required to avoid
leaking space.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8270
Increase the default allowed number of reconstruction attempts.
There's not an exact right number for this setting. It needs
to be set large enough to cover any realistic failure scenarios
and small enough to avoid stalling the IO pipeline and invoking
the dead man detection.
The current value of 256 was empirically determined to be too
low based on multi-day runs of ztest. The fault injection code
would inject more damage than could be reconstructed given the
relatively small number of attempts. However, in all observed
cases the block could be reconstructed using a slightly higher
limit.
Based on local testing increasing the default value to 4096 was
determined to strike the best balance. Checking all combinations
takes less than 10s in the worst case, and has so far eliminated
the vast majority of false positives detected by ztest. This
delay is roughly on par with how long retries may be performed
to a misbehaving HDD and was deemed to be reasonable. Better to
err on the side of a brief delay rather than fail to reconstruct
the data.
Lastly, the -Y flag has been added to zdb to make it easy to try all
possible combinations when performing split block reconstruction.
For badly damaged blocks with 18 splits, they can be fully enumerated
within a few minutes. This has been done to ensure permanent errors
are never incorrectly reported when ztest verifies the pool with zdb.
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8271
The implementation of 'zfs remap' has proven to be problematic since
it modifies the objset (but not its logical contents) by dirtying
metadata without owning it. The consequence of which is that
dmu_objset_remap_indirects() is vulnerable to certain races.
For example, if we are in the middle of receiving into the filesystem
while it is being remapped. Then it is possible we could evict the
objset when the receive completes (see dsl_dataset_clone_swap_sync_impl,
or dmu_recv_end_sync), but dmu_objset_remap_indirects() may be still
using the objset. The result of which would be a panic.
Extended runs of ztest(8) have exposed other possible races which
can occur when using 'zfs remap'. Several of these have been fixed
but there may be others which have not yet been encountered and
diagnosed.
Furthermore, the ability to manually remap a filesystem is no longer
particularly useful now that the removal code can map large chunks.
Coupled with the fact that explaining what this command does and why
it may be useful requires a detailed understanding of the internals
of device removal. These are details users should not be bothered
with.
Therefore, the 'zfs remap' command is being disabled but not entirely
removed. It may be removed in the future or potentially reworked
to address the issues described above. Since 'zfs remap' has never
been part of a tagged release its removal is expected to have
minimal impact.
The ZTS tests have been updated to continue to exercise the command
to prevent atrophy, but it has been removed entirely from ztest(8).
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8238
Some minor spelling mistakes and typos. No functional changes.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8272
Only display the full details of the vdev initialization state
in 'zpool status' output when requested with the -i option.
By default display '(initializing)' after vdevs when they are
being actively initialized. This is consistent with the
established precident of appending '(resilvering), etc' and
fits within the default 80 column terminal width making it
easy to read.
Additionally, updated the 'zpool initialize' documentation to
make it clear the options are mutually exclusive, but allow
duplicate options like all other zfs/zpool commands.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8230
PROBLEM
========
When invoking "zpool initialize" on a pool the command will
create a thread to initialize each disk. Unfortunately, it does
this serially across many transaction groups which can result
in commands taking a long time to return to the user and may
appear hung. The same thing is true when trying to suspend/cancel
the operation.
SOLUTION
=========
This change refactors the way we invoke the initialize interface
to ensure we can start or stop the intialization in just a few
transaction groups.
When stopping or cancelling a vdev initialization perform it
in two phases. First signal each vdev initialization thread
that it should exit, then after all threads have been signaled
wait for them to exit.
On a pool with 40 leaf vdevs this reduces the vdev initialize
stop/cancel time from ~10 minutes to under a second. The reason
for this is spa_vdev_initialize() no longer needs to wait on
multiple full TXGs per leaf vdev being stopped.
This commit additionally adds some missing checks for the passed
"initialize_vdevs" input nvlist. The contents of the user provided
input "initialize_vdevs" nvlist must be validated to ensure all
values are uint64s. This is done in zfs_ioc_pool_initialize() in
order to keep all of these checks in a single location.
Updated the innvl and outnvl comments to match the formatting used
for all other new sytle ioctls.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#8230
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
Almost all of the Python code in the respository has been updated
to be compatibile with Python 2.6, Python 3.4, or newer. The only
exceptions are arc_summery3.py which requires Python 3, and pyzfs
which requires at least Python 2.7. This allows us to maintain a
single version of the code and support most default versions of
python. This change does the following:
* Sets the default shebang for all Python scripts to python3. If
only Python 2 is available, then at install time scripts which
are compatible with Python 2 will have their shebangs replaced
with /usr/bin/python. This is done for compatibility until
Python 2 goes end of life. Since only the installed versions
are changed this means Python 3 must be installed on the system
for test-runner when testing in-tree.
* Added --with-python=<2|3|3.4,etc> configure option which sets
the PYTHON environment variable to target a specific python
version. By default the newest installed version of Python
will be used or the preferred distribution version when
creating pacakges.
* Fixed --enable-pyzfs configure checks so they are run when
--enable-pyzfs=check and --enable-pyzfs=yes.
* Enabled pyzfs for Python 3.4 and newer, which is now supported.
* Renamed pyzfs package to python<VERSION>-pyzfs and updated to
install in the appropriate site location. For example, when
building with --with-python=3.4 a python34-pyzfs will be
created which installs in /usr/lib/python3.4/site-packages/.
* Renamed the following python scripts according to the Fedora
guidance for packaging utilities in /bin
- dbufstat.py -> dbufstat
- arcstat.py -> arcstat
- arc_summary.py -> arc_summary
- arc_summary3.py -> arc_summary3
* Updated python-cffi package name. On CentOS 6, CentOS 7, and
Amazon Linux it's called python-cffi, not python2-cffi. For
Python3 it's called python3-cffi or python3x-cffi.
* Install one version of arc_summary. Depending on the version
of Python available install either arc_summary2 or arc_summary3
as arc_summary. The user output is only slightly different.
Reviewed-by: John Ramsden <johnramsden@riseup.net>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8096
The dmu_objset_remap_indirects_impl() logic depends on dnode_hold()
returning ENOENT for dnodes which will be freed and should be skipped.
This behavior can only be relied upon when taking a new hold and
while the caller has an open transaction. This ensures that the
open txg cannot advance and that a concurrent free will end up
in the same txg (which is critical). Relying on an existing hold
will not prevent dnode_free() from succeeding.
The solution is to take an additional dnode_hold() after assigning
the transaction. This ensures the remap will never dirty the dnode
if it was freed while we were waiting in dmu_tx_assign(, TXG_WAIT).
Randomly set zfs_object_remap_one_indirect_delay_ms in ztest. This
increases the likelihood of an operation racing with the remap.
Converted from ticks to milliseconds.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Tom Caputi <tcaputi@datto.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8215
Add an 'enclosure_symlinks' option to vdev_id.conf. This creates
consistently named symlinks to the enclosure devices (/dev/sg*) based
off the configuration in vdev_id.conf. The enclosure symlinks show
up in /dev/by-enclosure/<prefix>-<channel><num>. The links make it
make it easy to run sg_ses on a particular enclosure device. The
enclosure links are created in addition to the normal
/dev/disk/by-vdev links.
'enclosure_symlinks' is only valid in sas_direct configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Simon Guest <simon.guest@tesujimath.org>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8194
While unlikely it is possible for dsl_destroy_head() to return
ENOSPC in the ztest_objset_destroy_cb(). This can occur even
when ZFS_SPACE_CHECK_DESTROY is used with the dsl_sync_task().
Both the existence of a checkpoint and pending deferred frees
can cause this.
Reviewed-by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8206
As a result of the changes made in 8585, it's possible for an excessive
amount of vdev flush commands to be issued under some workloads.
Specifically, when the workload consists of mostly async write activity,
interspersed with some sync write and/or fsync activity, we can end up
issuing more flush commands to the underlying storage than is actually
necessary. As a result of these flush commands, the write latency and
overall throughput of the pool can be poorly impacted (latency
increases, throughput decreases).
Currently, any time an lwb completes, the vdev(s) written to as a result
of that lwb will be issued a flush command. The intenion is so the data
written to that vdev is on stable storage, prior to communicating to any
waiting threads that their data is safe on disk.
The problem with this scheme, is that sometimes an lwb will not have any
threads waiting for it to complete. This can occur when there's async
activity that gets "converted" to sync requests, as a result of calling
the zil_async_to_sync() function via zil_commit_impl(). When this
occurs, the current code may issue many lwbs that don't have waiters
associated with them, resulting in many flush commands, potentially to
the same vdev(s).
For example, given a pool with a single vdev, and a single fsync() call
that results in 10 lwbs being written out (e.g. due to other async
writes), that will result in 10 flush commands to that single vdev (a
flush issued after each lwb write completes). Ideally, we'd only issue a
single flush command to that vdev, after all 10 lwb writes completed.
Further, and most important as it pertains to this change, since the
flush commands are often very impactful to the performance of the pool's
underlying storage, unnecessarily issuing these flush commands can
poorly impact the performance of the lwb writes themselves. Thus, we
need to avoid issuing flush commands when possible, in order to acheive
the best possible performance out of the pool's underlying storage.
This change attempts to address this problem by changing the ZIL's logic
to only issue a vdev flush command when it detects an lwb that has a
thread waiting for it to complete. When an lwb does not have threads
waiting for it, the responsibility of issuing the flush command to the
vdevs involved with that lwb's write is passed on to the "next" lwb.
It's only once a write for an lwb with waiters completes, do we issue
the vdev flush command(s). As a result, now when we issue the flush(s),
we will issue them to the vdevs involved with that specific lwb's write,
but potentially also to vdevs involved with "previous" lwb writes (i.e.
if the previous lwbs did not have waiters associated with them).
Thus, in our prior example with 10 lwbs, it's only once the last lwb
completes (which will be the lwb containing the waiter for the thread
that called fsync) will we issue the vdev flush command; all of the
other lwbs will find they have no waiters, so they'll pass the
responsibility of the flush to the "next" lwb (until reaching the last
lwb that has the waiter).
Porting Notes:
* Reconciled conflicts with the fastwrite feature.
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Ported-by: Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9962
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/545190c6Closes#8188
This one line patch moves an assert in the function dump_dir()
below an error check that ensures it ran correctly. This ensures
zdb dumps the error that actually caused the problem, as opposed
to one of its symptoms.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8171
The verbose output of 'zpool list' was not correctly aligned due
to differences in the vdev name lengths. Minimally update the
code the correct the alignment using the same strategy employed
by 'zpool status'.
Missing dashes were added for the empty defaults columns, and
the vdev state is now printed for all vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7308Closes#8147
This patch fixes a small race condition in ztest_zil_remount()
that could result in a deadlock. ztest_device_removal() calls
spa_vdev_remove() which may eventually call spa_reset_logs().
If ztest_zil_remount() attempts to call zil_close() while this
is happening, it may fail when it asserts !zilog_is_dirty(zilog).
This patch simply adds locking to correct the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8154
This commit fixes the following ASSERT in zfs_receive_one() when
receiving a send stream from a root dataset with the "-e" option:
$ sudo zfs snap source@snap
$ sudo zfs send source@snap | sudo zfs recv -e destination/recv
chopprefix > drrb->drr_toname
ASSERT at libzfs_sendrecv.c:3804:zfs_receive_one()
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8121
ztest currently uses the boolean flag ztest_device_removal_active
to protect some tests that may not run successfully if they occur
at the same time as ztest_device_removal(). Unfortunately, in the
event that ztest is in the middle of a device removal when it
decides to issue a SIGKILL, the device removal will be
automatically restarted (without setting the flag) when the pool
is re-imported on the next run. This patch corrects this by
ensuring that any in-progress removals are completed before running
further tests after the re-import.
This patch also makes a few small changes to prevent race conditions
involving the creation and destruction of spa->spa_vdev_removal,
since this field is not protected by any locks. Some checks that
may run concurrently with setting / unsetting this field have been
updated to check spa->spa_removing_phys.sr_state instead. The most
significant change here is that spa_removal_get_stats() no longer
accounts for in-flight work done, since that could result in a NULL
pointer dereference.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8105
This change allows 'zpool split' to work with whole-disk devices and
updates the ZFS Test Suite with a new script to exercise this
functionality.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6643Closes#8133
Porting Notes:
* Use thread pools (tpool) API instead of introducing taskq interfaces
to libzfs.
* Use pthread_mutext for locks as mutex_t isn't available.
* Ignore alternative libshare initialization since OpenZFS-7955 is
not present on zfsonlinux.
Authored by: Sebastien Roy <seb@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Authored by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Matt Ahrens <mahrens@delphix.com>
Ported-by: Don Brady <don.brady@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8115
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a3f0e2b569Closes#8092
This commit adds a new test case to the ZFS Test Suite to verify ZED
can detect when a device is physically removed from a running system:
the device will be offlined if a spare is not available in the pool.
We implement this by using the existing libudev functionality and
without relying solely on the FM kernel module capabilities which have
been observed to be unreliable with some kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1537Closes#7926
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
ztest occasionally hits an assert that !zilog_is_dirty() during
zil_close(). This is caused by an interaction between 2 threads.
First, ztest_run() waits for each test thread to complete and
closes the associated dataset as soon as the thread joins. At
the same time, the ztest_vdev_add_remove() test may attempt to
remove the slog, which will open, dirty, and reset the logs on
every dataset in the pool (including those of other threads).
This patch simply ensures that we always join all of the test
threads before closing any datasets.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8094
This patch ensures that logs are replayed on all datasets prior
to starting ztest workers. This ensures that the call to
vdev_offline() a log device in ztest_fault_inject() will not fail
due to the log device being required for replay.
This patch also fixes a small issue found during testing where
spa_keystore_load_wkey() does not check that the dataset specified
is an encryption root. This check was present in libzfs, however.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8084
Tom Caputi
Brian Behlendorf
Olaf Faaland
kpande
jwittlincohen
Alek P
Allan Jude
Matthew Ahrens
Paul Zuchowski
Igor K
Serapheim Dimitropoulos
bunder2015
Tony Hutter
loli10K
Damian Wojsław
George Wilson
Prakash Surya
Sebastien Roy
loli10K