This patch fixes 2 issues with raw, deduplicated send streams. The
first is that datasets who had been completely received earlier in
the stream were not still marked as raw receives. This caused
problems when newly received datasets attempted to fetch raw data
from these datasets without this flag set.
The second problem was that the arc freeze checksum code was not
consistent about which locks needed to be held while performing
its asserts. The proper locking needed to run these asserts is
actually fairly nuanced, since the asserts touch the linked list
of buffers (requiring the header lock), the arc_state (requiring
the b_evict_lock), and the b_freeze_cksum (requiring the
b_freeze_lock). This seems like a large performance sacrifice and
a lot of unneeded complexity to verify that this relatively small
debug feature is working as intended, so this patch simply removes
these asserts instead.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7701
Since zdb opens the pools read-only, it cannot damage the pool in the
event the pool is already imported either on the same host or on
another one.
If the pool vdev structure is changing while zdb is importing the
pool, it may cause zdb to crash. However this is unlikely, and in any
case it's a user space process and can simply be run again.
For this reason, zdb should disable the multihost activity test on
import that is normally run.
This commit fixes a few zdb code paths where that had been overlooked.
It also adds tests to ensure that several common use cases handle this
properly in the future.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Gu Zheng <guzheng2331314@163.com>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7797Closes#7801
The following patch introduces a few statistics on reads and writes
grouped by dataset. These statistics are implemented as kstats
(backed by aggregate sums for performance) and can be retrieved by
using the dataset objset ID number. The motivation for this change is
to provide some preliminary analytics on dataset usage/performance.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#7705
Removing hardcoded paths in events.cfg
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7805
Removing hardcoded paths in largest_pool_001
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7804
Removing hardcoded paths in privilege group tests
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7803
Allow the 'zpool replace' to run slowly without overwhelming the vdev
queues by setting zfs_scan_vdev_limit=128k. This limits the number of
concurrent slow IOs which need to be handled. The net effect is the
test case runs approximately 3x faster putting it well under the 10
minute per-test time limit.
Rename import_cache* test cases to imprt_cachefile*. Originally
these were renamed due to a maximum tar name limit, this limit was
removed by commit 1dfde3d9b.
Replaced instances of /var/tmp in zpool_import.cfg with $TEST_BASE_DIR.
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7765Closes#7802
It's possible for an unrelated process, like blkid, to have the
volume open when 'zfs destroy' is run. Switch the cleanup function
to the destroy_dataset() helper which handles this case by retrying
the destroy when the dataset is busy.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7796
Traditionally Automake has defaulted to the V7 tar format when
creating tarballs for distributions. One of the many limitions
of this format is a 99 character maximum path + file name limit.
This can cause problems when adding new test cases to the ZTS
due to the depth of the sub-tree and descriptive test names.
This change switches the build system to the posix (aliased as
pax) tar format which conforms to the POSIX.1-2001 specification.
This format does not suffer from the V7 limitations, was designed
to be compatible, and will become the default format in future
versions of GNU tar.
https://www.gnu.org/software/tar/manual/html_chapter/tar_8.html
As part of this change the blockfiles directories which were
originally removed due to this limit have been readded.
Reviewed by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7767
One small integration that was absent from b52563 was
support for zfs recv -o / -x with regards to encryption
parameters. The main use cases of this are as follows:
* Receiving an unencrypted stream as encrypted without
needing to create a "dummy" encrypted parent so that
encryption can be inheritted.
* Allowing users to change their keylocation on receive,
so long as the receiving dataset is an encryption root.
* Allowing users to explicitly exclude or override the
encryption property from an unencrypted properties stream,
allowing it to be received as encrypted.
* Receiving a recursive heirarchy of unencrypted datasets,
encrypting the top-level one and forcing all children to
inherit the encryption.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7650
Removing hardcoded paths in delegate group tests
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7778
Removing hardcoded paths in acl group tests
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7777
Removing hardcoded path in inuse_004
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7775
Removing hardcoded path in projectquota_002
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7774
* Both cli_root/zpool_import/import_cache_device_replaced, and
redundancy/redundancy_004_neg have been observed to fail for
spurious reasons ~1% of the time. Add them to the exception
list and reference the open Github issue.
* Speed up replacement/replacement_001_pos to prevent it from
exceeding the 10 minute per test limit and getting KILLED.
File vdev creation switched to truncate -s, redundant raidz1
testing pass dropped, fixed some minor formating issues.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7766
This change modifies how 'checksum' and 'dedup' properties are verified
in zfs_check_settable() handling the case where they are explicitly
inherited in the dataset hierarchy when receiving a recursive send
stream.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7755Closes#7576Closes#7757
It's possible for an unrelated process, like blkid, to have the
volume open when 'zfs destroy' is run. Switch the cleanup function
to the destroy_dataset() helper which handles this case by retrying
the destroy when the dataset is busy.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7763
Overview
========
We parallelize the allocation process by creating the concept of
"allocators". There are a certain number of allocators per metaslab
group, defined by the value of a tunable at pool open time. Each
allocator for a given metaslab group has up to 2 active metaslabs; one
"primary", and one "secondary". The primary and secondary weight mean
the same thing they did in in the pre-allocator world; primary metaslabs
are used for most allocations, secondary metaslabs are used for ditto
blocks being allocated in the same metaslab group. There is also the
CLAIM weight, which has been separated out from the other weights, but
that is less important to understanding the patch. The active metaslabs
for each allocator are moved from their normal place in the metaslab
tree for the group to the back of the tree. This way, they will not be
selected for use by other allocators searching for new metaslabs unless
all the passive metaslabs are unsuitable for allocations. If that does
happen, the allocators will "steal" from each other to ensure that IOs
don't fail until there is truly no space left to perform allocations.
In addition, the alloc queue for each metaslab group has been broken
into a separate queue for each allocator. We don't want to dramatically
increase the number of inflight IOs on low-end systems, because it can
significantly increase txg times. On the other hand, we want to ensure
that there are enough IOs for each allocator to allow for good
coalescing before sending the IOs to the disk. As a result, we take a
compromise path; each allocator's alloc queue max depth starts at a
certain value for every txg. Every time an IO completes, we increase the
max depth. This should hopefully provide a good balance between the two
failure modes, while not dramatically increasing complexity.
We also parallelize the spa_alloc_tree and spa_alloc_lock, which cause
very similar contention when selecting IOs to allocate. This
parallelization uses the same allocator scheme as metaslab selection.
Performance Results
===================
Performance improvements from this change can vary significantly based
on the number of CPUs in the system, whether or not the system has a
NUMA architecture, the speed of the drives, the values for the various
tunables, and the workload being performed. For an fio async sequential
write workload on a 24 core NUMA system with 256 GB of RAM and 8 128 GB
SSDs, there is a roughly 25% performance improvement.
Future Work
===========
Analysis of the performance of the system with this patch applied shows
that a significant new bottleneck is the vdev disk queues, which also
need to be parallelized. Prototyping of this change has occurred, and
there was a performance improvement, but more work needs to be done
before its stability has been verified and it is ready to be upstreamed.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Alexander Motin <mav@FreeBSD.org>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Porting Notes:
* Fix reservation test failures by increasing tolerance.
OpenZFS-issue: https://illumos.org/issues/9112
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3f3cc3c3Closes#7682
As reported by https://github.com/zfsonlinux/zfs/issues/4996, there is
yet another hole birth issue. In this one, if a block is entirely holes,
but the birth times are not all the same, we lose that information by
creating one hole with the current txg as its birth time.
The ZoL PR's fix approach is incorrect. Ultimately, the problem here is
that when you truncate and write a file in the same transaction group,
the dbuf for the indirect block will be zeroed out to deal with the
truncation, and then written for the write. During this process, we will
lose hole birth time information for any holes in the range. In the case
where a dnode is being freed, we need to determine whether the block
should be converted to a higher-level hole in the zio pipeline, and if
so do it when the dnode is being synced out.
Porting Notes:
* The DMU_OBJECT_END change in zfs_znode.c was already applied.
* Added test cases from #5675 provided by @rincebrain for hole_birth
issues. These test cases should be pushed upstream to OpenZFS.
* Updated mk_files which is used by several rsend tests so the
files created are a little more interesting and may contain holes.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9438
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/738e2a3c
External-issue: DLPX-46861
Closes#7746
It's possible for an unrelated process, like blkid, to have the
volume open when 'zfs destroy' is run. Switch the cleanup function
to the destroy_dataset() helper which handles this case by retrying
the destroy when the dataset is busy.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7750
The reservation_008_pos test case has been observed to fail in
a non-dangerous way in approximately 5% of automated test runs.
Add the test case to the list of possible expected failures
until the test case can be made perfectly reliable.
Reviewed by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #7741Closes#7742
While the autoexpand property may seem like a small feature it
depends on a significant amount of system infrastructure. Enough
of that infrastructure is now in place that with a few modifications
for Linux it can be supported.
Auto-expand works as follows; when a block device is modified
(re-sized, closed after being open r/w, etc) a change uevent is
generated for udev. The ZED, which is monitoring udev events,
passes the change event along to zfs_deliver_dle() if the disk
or partition contains a zfs_member as identified by blkid.
From here the device is matched against all imported pool vdevs
using the vdev_guid which was read from the label by blkid. If
a match is found the ZED reopens the pool vdev. This re-opening
is important because it allows the vdev to be briefly closed so
the disk partition table can be re-read. Otherwise, it wouldn't
be possible to report the maximum possible expansion size.
Finally, if the property autoexpand=on a vdev expansion will be
attempted. After performing some sanity checks on the disk to
verify that it is safe to expand, the primary partition (-part1)
will be expanded and the partition table updated. The partition
is then re-opened (again) to detect the updated size which allows
the new capacity to be used.
In order to make all of the above possible the following changes
were required:
* Updated the zpool_expand_001_pos and zpool_expand_003_pos tests.
These tests now create a pool which is layered on a loopback,
scsi_debug, and file vdev. This allows for testing of non-
partitioned block device (loopback), a partition block device
(scsi_debug), and a file which does not receive udev change
events. This provided for better test coverage, and by removing
the layering on ZFS volumes there issues surrounding layering
one pool on another are avoided.
* zpool_find_vdev_by_physpath() updated to accept a vdev guid.
This allows for matching by guid rather than path which is a
more reliable way for the ZED to reference a vdev.
* Fixed zfs_zevent_wait() signal handling which could result
in the ZED spinning when a signal was not handled.
* Removed vdev_disk_rrpart() functionality which can be abandoned
in favor of kernel provided blkdev_reread_part() function.
* Added a rwlock which is held as a writer while a disk is being
reopened. This is important to prevent errors from occurring
for any configuration related IOs which bypass the SCL_ZIO lock.
The zpool_reopen_007_pos.ksh test case was added to verify IO
error are never observed when reopening. This is not expected
to impact IO performance.
Additional fixes which aren't critical but were discovered and
resolved in the course of developing this functionality.
* Added PHYS_PATH="/dev/zvol/dataset" to the vdev configuration for
ZFS volumes. This is as good as a unique physical path, while the
volumes are not used in the test cases anymore for other reasons
this improvement was included.
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#120Closes#2437Closes#5771Closes#7366Closes#7582Closes#7629
This project's goal is to make read-heavy channel programs and zfs(1m)
administrative commands faster by caching all the metadata that they will
need in the dbuf layer. This will prevent the data from being evicted, so
that any future call to i.e. zfs get all won't have to go to disk (very
much). There are two parts:
The dbuf_metadata_cache. We identify what to put into the cache based on
the object type of each dbuf. Caching objset properties os
{version,normalization,utf8only,casesensitivity} in the objset_t. The reason
these needed to be cached is that although they are queried frequently,
they aren't stored in a dbuf type which we can easily recognize and cache in
the dbuf layer; instead, we have to explicitly store them. There's already
existing infrastructure for maintaining cached properties in the objset
setup code, so I simply used that.
Performance Testing:
- Disabled kmem_flags
- Tuned dbuf_cache_max_bytes very low (128K)
- Tuned zfs_arc_max very low (64M)
Created test pool with 400 filesystems, and 100 snapshots per filesystem.
Later on in testing, added 600 more filesystems (with no snapshots) to make
sure scaling didn't look different between snapshots and filesystems.
Results:
| Test | Time (trunk / diff) | I/Os (trunk / diff) |
+------------------------+---------------------+---------------------+
| zpool import | 0:05 / 0:06 | 12.9k / 12.9k |
| zfs get all (uncached) | 1:36 / 0:53 | 16.7k / 5.7k |
| zfs get all (cached) | 1:36 / 0:51 | 16.0k / 6.0k |
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Thomas Caputi <tcaputi@datto.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
OpenZFS-issue: https://illumos.org/issues/9337
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7dec52fCloses#7668
Datasets that are deeply nested (~100 levels) are impractical. We just
put a limit of 50 levels to newly created datasets. Existing datasets
should work without a problem.
The problem can be seen by attempting to create a dataset using the -p
option with many levels:
panic[cpu0]/thread=ffffff01cd282c20: BAD TRAP: type=8 (#df Double fault) rp=ffffffff
fffffffffbc3aa60 unix:die+100 ()
fffffffffbc3ab70 unix:trap+157d ()
ffffff00083d7020 unix:_patch_xrstorq_rbx+196 ()
ffffff00083d7050 zfs:dbuf_rele+2e ()
...
ffffff00083d7080 zfs:dsl_dir_close+32 ()
ffffff00083d70b0 zfs:dsl_dir_evict+30 ()
ffffff00083d70d0 zfs:dbuf_evict_user+4a ()
ffffff00083d7100 zfs:dbuf_rele_and_unlock+87 ()
ffffff00083d7130 zfs:dbuf_rele+2e ()
... The block above repeats once per directory in the ...
... create -p command, working towards the root ...
ffffff00083db9f0 zfs:dsl_dataset_drop_ref+19 ()
ffffff00083dba20 zfs:dsl_dataset_rele+42 ()
ffffff00083dba70 zfs:dmu_objset_prefetch+e4 ()
ffffff00083dbaa0 zfs:findfunc+23 ()
ffffff00083dbb80 zfs:dmu_objset_find_spa+38c ()
ffffff00083dbbc0 zfs:dmu_objset_find+40 ()
ffffff00083dbc20 zfs:zfs_ioc_snapshot_list_next+4b ()
ffffff00083dbcc0 zfs:zfsdev_ioctl+347 ()
ffffff00083dbd00 genunix:cdev_ioctl+45 ()
ffffff00083dbd40 specfs:spec_ioctl+5a ()
ffffff00083dbdc0 genunix:fop_ioctl+7b ()
ffffff00083dbec0 genunix:ioctl+18e ()
ffffff00083dbf10 unix:brand_sys_sysenter+1c9 ()
Porting notes:
* Added zfs_max_dataset_nesting module option with documentation.
* Updated zfs_rename_014_neg.ksh for Linux.
* Increase the zfs.sh stack warning to 15K. Enough time has passed
that 16K can be reasonably assumed to be the default value. It
was increased in the 3.15 kernel released in June of 2014.
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
OpenZFS-issue: https://www.illumos.org/issues/9330
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/757a75aCloses#7681
Remove the dependency on partitionable devices for the clean_mirror
and scrub_mirror test cases. This allows for the setup and cleanup
of the test cases to be simplified by removing the need for complex
partitioning.
This change also resolves a issue where the clean_mirror devices
were not being properly damaged since the device name was not a
full path. The result being loopX files were being left in the
top level test_results directory.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7434Closes#7690
Motivation
==========
The current space map encoding has the following disadvantages:
[1] Assuming 512 sector size each entry can represent at most 16MB for a segment.
This makes the encoding very inefficient for large regions of space.
[2] As vdev-wide space maps have started to be used by new features (i.e.
device removal, zpool checkpoint) we've started imposing limits in the
vdevs that can be used with them based on the maximum addressable offset
(currently 64PB for a top-level vdev).
New encoding
============
The layout can be found at space_map.h and it remains backwards compatible with
the old one. The introduced two-word entry format, besides extending the limits
imposed by the single-entry layout, also includes a vdev field and some extra
padding after its prefix.
The extra padding after the prefix should is reserved for future usage (e.g.
new prefixes for future encodings or new fields for flags). The new vdev field
not only makes the space maps more self-descriptive, but also opens the doors
for pool-wide space maps (expected to be used in the log spacemap project).
One final important note is that the number of bits used for vdevs is reduced
to 24 bits for blkptrs. That was decided as we don't know of any setups that
use more than 16M vdevs for the time being and we wanted to fit the vdev field
in the space map. In addition that gives us some extra bits in dva_t.
Other references:
=================
The new encoding is also discussed towards the end of the Log Space Map
presentation from 2017's OpenZFS summit.
Link: https://www.youtube.com/watch?v=jj2IxRkl5bQ
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Gordon Ross <gwr@nexenta.com>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/90a56e6d
OpenZFS-issue: https://www.illumos.org/issues/9238Closes#7665
This change introduces a new performance test which does random reads
and writes, but instead of using `bssplit` to determine the block size,
it uses a fixed blocksize. Additionally, some new IO sizes are added to
other tests and timestamp data is recorded with the performance data.
Authored by: Ahmed Gahnem <ahmedg@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: John Wren Kennedy <john.kennedy@delphix.com>
Requires-builders: perf
OpenZFS-issue: https://www.illumos.org/issues/9184
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/659
External-issue: DLPX-46724
Closes#7660
The enospc_002_pos test case would frequently fail due a command
succeeding when it was expected to fail due to lack of space.
In order to make this far less likely, files are created across
multiple transaction groups in order to consume as many unused
blocks as possible.
The dependency that the tests run on a partitioned block device
has been removed. It's simpler to use sparse files.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7663
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
Otherwise the output is consumed by the output redirection.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Closes#7570
ms_shift can be incorrectly changed changed in MOS config for
indirect vdevs that have been historically expanded
According to spa_config_update() we expect new vdevs to have
vdev_ms_array equal to 0 and then we go ahead and set their metaslab
size. The problem is that indirect vdevs also have vdev_ms_array == 0
because their metaslabs are destroyed once their removal is done.
As a result, if a vdev was expanded and then removed may have its
ms_shift changed if another vdev was added after its removal.
Fortunately this behavior does not cause any type of crash or bad
behavior in the kernel but it can confuse zdb and anyone doing any kind
of analysis of the history of the pools.
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Prashanth Sreenivasa <pks@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/651
OpenZFS-issue: https://illumos.org/issues/9591a
External-issue: DLPX-58879
Closes#7644
Adopt and extend the OpenZFS ZTS results analysis script for use
with ZFS on Linux. This allows for automatic analysis of tests
which may be skipped for a variety or reasons or which are not
entirely reliable.
In addition to the list of 'known' failures, which have been updated
for ZFS on Linux, there in a new 'maybe' section. This mapping
include tests which might be correctly skipped depending on the
test environment. This may be because of a missing dependency or
lack of required kernel support. This list also includes tests
which normally pass but might on occasion fail for a harmless
reason.
The script was also extended include a reason for why a given test
might be skipped or may fail. The reason will be included after
the test in the "results other than PASS that are expected" section.
For failures it is preferable to set the reason to the GitHub issue
number and for skipped tests several generic reasons are available.
You may also specify a custom reason if needed.
All tests were added back in to the linux.run file even if they are
expected to failed. There is value in running tests which may not
pass, the expected results for these tests has been encoded in
the new analysis script.
All tests which were disabled because they ran more slowly on a
32-bit system have been re-enabled. Developers working on 32-bit
systems should assess what it reasonable for their environment.
The unnecessary dependency on physical block devices was removed for
the checksum, grow_pool, and grow_replicas test groups so they are
no longer skipped. Updated the filetest_001_pos test case to run
properly now that it is enabled and moved the grow tests in to a
single directory.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7638
This patch adds tunables for modifying the maximum memory limit and
maximum instruction limit that can be specified when running a channel
program.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
External-issue: LX-1085
Closes#7618
In the cleanup for the privilege tests, an empty variable, empty because
the corresponding setup is skipped on Linux, results in /export/home
being deleted. This patch adds an assertion that the variable is not
empty, and causes the cleanup to be skipped on Linux as well.
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
External-issue: LX-1099
Closes#7615
user_run leaves two files in /tmp, moving them to $TEST_BASE_DIR and
adding them to the default cleanup routine.
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7614
zpool and zed place scripts in subdirectories of libexecdir. Some
distributions locate architecture independent scripts in other locations
(e.g. Debian). To avoid these paths getting out of sync, centralize the
definitions.
Build zfs-test's default.cfg by Makefile. Use the new directory
logic building tests/zfs-tests/include/default.cfg.in.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7597
This patch collects some minor inconsistencies and typos in the
documentation, logging and testing infrastructure.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7608
Currently, during a recursive zfs destroy the first error that is
encountered will stop the destruction of the datasets. Errors may
happen for a variety of reasons including competing deletions
and busy datasets.
This patch switches recursive destroy to always do a best-effort
recursive dataset destroy.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7574
History tests were hard coded to use /tmp and didn't clean up
properly after testing.
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Issue #7507Closes#7600
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
Test 13 would fail because of attempts to zpool destroy -f a pool that
was still busy. Changed those calls to destroy_pool which does a retry
loop, and the problem is no longer reproducible. Also removed some non
functional code in the test which is why it was originally commented out
by placing it after the call to log_pass.
Test 14 would fail because sometimes the check for a degraded pool would
complete before the pool had changed state. Changed the logic to check
in a loop with a timeout and the problem is no longer reproducible.
Authored by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Yuri Pankov <yuripv@yuripv.net>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Dan McDonald <danmcd@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
* Re-enabled slog_013_pos.ksh
OpenZFS-issue: https://illumos.org/issues/9245
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/8f323b5Closes#7585
Update bdev_capacity to have wholedisk vdevs query the
size of the underlying block device (correcting for the size
of the efi parition and partition alignment) and therefore detect
expanded space.
Correct vdev_get_stats_ex so that the expandsize is aligned
to metaslab size and new space is only reported if it is large
enough for a new metaslab.
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
External-issue: LX-165
Closes#7546
Issue #7582
This adds a new test to measure ZIL performance.
- Adds the ability to induce IO delays with zinject
- Adds a new variable (PERF_NTHREADS_PER_FS) to allow fio threads to
be distributed to individual file systems as opposed to all IO going
to one, as happens elsewhere.
- Refactoring of do_fio_run
Authored by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: John Wren Kennedy <jwk404@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9082
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/634
External-issue: DLPX-48625
Closes#7491
Minimal changes required to integrate the SPL sources in to the
ZFS repository build infrastructure and packaging.
Build system and packaging:
* Renamed SPL_* autoconf m4 macros to ZFS_*.
* Removed redundant SPL_* autoconf m4 macros.
* Updated the RPM spec files to remove SPL package dependency.
* The zfs package obsoletes the spl package, and the zfs-kmod
package obsoletes the spl-kmod package.
* The zfs-kmod-devel* packages were updated to add compatibility
symlinks under /usr/src/spl-x.y.z until all dependent packages
can be updated. They will be removed in a future release.
* Updated copy-builtin script for in-kernel builds.
* Updated DKMS package to include the spl.ko.
* Updated stale AUTHORS file to include all contributors.
* Updated stale COPYRIGHT and included the SPL as an exception.
* Renamed README.markdown to README.md
* Renamed OPENSOLARIS.LICENSE to LICENSE.
* Renamed DISCLAIMER to NOTICE.
Required code changes:
* Removed redundant HAVE_SPL macro.
* Removed _BOOT from nvpairs since it doesn't apply for Linux.
* Initial header cleanup (removal of empty headers, refactoring).
* Remove SPL repository clone/build from zimport.sh.
* Use of DEFINE_RATELIMIT_STATE and DEFINE_SPINLOCK removed due
to build issues when forcing C99 compilation.
* Replaced legacy ACCESS_ONCE with READ_ONCE.
* Include needed headers for `current` and `EXPORT_SYMBOL`.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7556
Stack profiling is quite useful and Linux ZFS test suite does not
current collect that data.
Linux perf is a common tool for this purpose though the perf record
data file can be quite large. With this change, Linux ZFS perf tests
capture perf record data if perf is installed on the system and
PERF_DO_PROFILING environment variable is set.
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
External-issue: LX-971
Closes#7549
- there are more options now
- command examples are more readable in code style
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#7538
It's possible for the `zpool attach` portion of this test case
to complete before the `zpool scrub` can be issued. Update the
test case to force the resilvering phase to take longer.
Reviewed-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5444Closes#7541
In CentOS 7.5 the kernel provided a compatibility wrapper to support
O_TMPFILE. This results in the test setup script correctly detecting
kernel support. But the ZFS module was built without O_TMPFILE
support due to the non-standard CentOS kernel interface.
Handle this case by updating the setup check to fail either when
the kernel or the ZFS module fail to provide support. The reason
will be clearly logged in the test results.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7528
Must clear slow-disk zinject injections in test cleanup routine.
Otherwise, when this test fails, it causes most subsequent tests
to fail.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9190
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/762c6b4Closes#7530
Incorrect shebangs were used when porting.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7523Closes#7524
Removing hard-coded path used in enospc_002
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7515
Don't create an ext4 file system atop $DEV_DISKDIR/$DISK2.
There's likely to not be sufficient space for it to succeed.
Instead, simply create the vdev files in the directory where it
would have been mounted.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7459
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
* Added tuning to man page.
* Test case changes dropped, default behavior unchanged.
OpenZFS-issue: https://www.illumos.org/issues/9256
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/32356b3c56Closes#7470
Creating a pool with a temporary name fails when we also specify custom
dataset properties: this is because we mistakenly call
zfs_set_prop_nvlist() on the "real" pool name which, as expected,
cannot be found because the SPA is present in the namespace with the
temporary name.
Fix this by specifying the correct pool name when setting the dataset
properties.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7502Closes#7509
Commit 7fab6361 inadvertently disabled the MMP test cases by creating
and not removing an /etc/hostid file in the new zpool_split_props test
case. When the file exists the ZTS skips the entire MMP test group
rather than modify what may be a system which is already configured.
Update the test case to remove the file.
Additionally, because the MMP tests were disabled a regression slipped
in as part of commit 9eb7b46ed0. Fix it.
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7514
Caught during path cleanups, the files referenced do not appear to be
created or used anywhere.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7508
When using mawk instead of gawk zfs_diff_timestamp fails consistently:
this is due to a subtle difference in how mawk handles substr().
From awk(1):
---
Finally, here is how mawk handles exceptional cases not discussed in
the AWK book or the Posix draft. It is unsafe to assume consistency
across awks and safe to skip to the next section.
substr(s, i, n) returns the characters of s in the intersection of
the closed interval [1, length(s)] and the half-open interval [i, i+n).
When this intersection is empty, the empty string is returned; so
substr("ABC", 1, 0) = "" and substr("ABC", -4, 6) = "A".
---
To support running zfs_diff_timestamp with both gawk and mawk change
the second parameter passed to substr().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7503Closes#7510
This patch adds the ability for zinject to trigger decryption
and authentication faults in the ZIO and ARC layers. This
functionality is exposed via the new "decrypt" error type, which
may be provided for "data" object types.
This patch also refactors some of the core encryption / decryption
functions so that they have consistent prototypes, handle errors
consistently, and do not have unused arguments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7474
Two deadlocks / ASSERT failures were introduced in a2c2ed1b which
would occur whenever arc_buf_fill() failed to decrypt a block of
data. This occurred because the call to arc_buf_destroy() which
was responsible for cleaning up the newly created buffer would
attempt to take out the hdr lock that it was already holding. This
was resolved by calling the underlying functions directly without
retaking the lock.
In addition, the dmu_diff() code did not properly ensure that keys
were loaded and mapped before begining dataset traversal. It turns
out that this code does not need to look at any encrypted values,
so the code was altered to perform raw IO only.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7354Closes#7456
This commit introduces several changes:
* Update LICENSE and project information
* Give a good PEP8 talk to existing Python source code
* Add RPM/DEB packaging for pyzfs
* Fix some outstanding issues with the existing pyzfs code caused by
changes in the ABI since the last time the code was updated
* Integrate pyzfs Python unittest with the ZFS Test Suite
* Add missing libzfs_core functions: lzc_change_key,
lzc_channel_program, lzc_channel_program_nosync, lzc_load_key,
lzc_receive_one, lzc_receive_resumable, lzc_receive_with_cmdprops,
lzc_receive_with_header, lzc_reopen, lzc_send_resume, lzc_sync,
lzc_unload_key, lzc_remap
Note: this commit slightly changes zfs_ioc_unload_key() ABI. This allow
to differentiate the case where we tried to unload a key on a
non-existing dataset (ENOENT) from the situation where a dataset has
no key loaded: this is consistent with the "change" case where trying
to zfs_ioc_change_key() from a dataset with no key results in EACCES.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7230
When receiving an incremental send stream with intermediary snapshots
zfs_receive_one() does not correctly identify the top-level dataset:
consequently we restore said snapshots as if they were children
datasets in the hierarchy, forcing inheritance of any property received
with 'zfs send -o' and effectively removing any locally set value.
The test case did not correctly verify this situation because it uses
adjacent snapshots, basically testing 'zfs send -i' instead of
'zfs send -I': this commit adds an additional intermediary snapshot to
the test script.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7478
Data loss was identified in #7401 when many small files were copied.
This adds a reproducer for this bug and other similar ones: randomly
generate N files. Then, listing M of them by `ls -U` order, produce
those same files in a directory of the same name.
This triggers the bug consistently, provided N and M are large enough.
Here, N=2^16 and M=2^13.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7411
Only filesystems and volumes are valid 'zfs remap' parameters: when
passed a snapshot name zfs_remap_indirects() does not handle the
EINVAL returned from libzfs_core, which results in failing an assertion
and consequently crashing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7454
Commit cc63068 caused ENOSPC error when copy a large amount of files
between two directories. The reason is that the patch limits zap leaf
expansion to 2 retries, and return ENOSPC when failed.
The intent for limiting retries is to prevent pointlessly growing table
to max size when adding a block full of entries with same name in
different case in mixed mode. However, it turns out we cannot use any
limit on the retry. When we copy files from one directory in readdir
order, we are copying in hash order, one leaf block at a time. Which
means that if the leaf block in source directory has expanded 6 times,
and you copy those entries in that block, by the time you need to expand
the leaf in destination directory, you need to expand it 6 times in one
go. So any limit on the retry will result in error where it shouldn't.
Note that while we do use different salt for different directories, it
seems that the salt/hash function doesn't provide enough randomization
to the hash distance to prevent this from happening.
Since cc63068 has already been reverted. This patch adds it back and
removes the retry limit.
Also, as it turn out, failing on zap_add() has a serious side effect for
mzap_upgrade(). When upgrading from micro zap to fat zap, it will
call zap_add() to transfer entries one at a time. If it hit any error
halfway through, the remaining entries will be lost, causing those files
to become orphan. This patch add a VERIFY to catch it.
Reviewed-by: Sanjeev Bagewadi <sanjeev.bagewadi@gmail.com>
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#7401Closes#7421
This patch fixes 2 issues in how spill blocks are processed during
raw sends. The first problem is that compressed spill blocks were
using the logical length rather than the physical length to
determine how much data to dump into the send stream. The second
issue is a typo that caused the spill record's object number to be
used where the objset's ID number was required. Both issues have
been corrected, and the payload_size is now printed in zstreamdump
for future debugging.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7378Closes#7432
Currently, when the receive_object() code wants to reclaim an
object, it always assumes that the dnode is the legacy 512 bytes,
even when the incoming bonus buffer exceeds this length. This
causes a buffer overflow if --enable-debug is not provided and
triggers an ASSERT if it is. This patch resolves this issue and
adds an ASSERT to ensure this can't happen again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7097Closes#7433
When using large disks the integers for calculating sizes can
overflow past 2**31. Changing to long integers with typeset
should correct this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#4444Closes#7451
Authored by: Matt Ahrens <Matt.Ahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9280
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/243952cCloses#7445
zpool_create_002_pos did not clean up filedisk files left over from
running the test.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7435Closes#7439
Authored by: Toomas Soome <tsoome@me.com>
Reviewed by: C Fraire <cfraire@me.com>
Reviewed by: Andy Fiddaman <omnios@citrus-it.co.uk>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Approved by: Joshua M. Clulow <josh@sysmgr.org>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting Notes:
* The additional instances of this typo addressed in the OpenZFS
patch were already resolved.
OpenZFS-issue: https://illumos.org/issues/9213
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/edc8ef7d92Closes#7436
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
This test performs a rapid offline/online cycle of each of several
mirror vdevs. It can run so quickly that there isn't sufficient pool
redundancy to perform an offline. The solution is to wait until the
pool is resilvered following the online operation.
Also, add a pool sync before the offline operation to help reduce
spurious errors.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Issue #6900
Currently mounting an already mounted zfs dataset results in an
error, whereas it is typically allowed with other filesystems.
This causes some bad interactions with mount namespaces. Take
this sequence for example:
- Create a dataset
- Create a snapshot of the dataset
- Create a clone of the snapshot
- Create a new mount namespace
- Rename the original dataset
The rename results in unmounting and remounting the clone in the
original mount namespace, however the remount fails because the
dataset is still mounted in the new mount namespace. (Note that
this means the mount in the new mount namespace is never being
unmounted, so perhaps the unmount/remount of the clone isn't
actually necessary.)
The problem here is a result of the way mounting is implemented
in the kernel module. Since it is not mounting block devices it
uses mount_nodev() instead of the usual mount_bdev(). However,
mount_nodev() is written for filesystems for which each mount is
a new instance (i.e. a new super block), and zfs should be able
to detect when a mount request can be satisfied using an existing
super block.
Change zpl_mount() to call sget() directly with it's own test
callback. Passing the objset_t object as the fs data allows
checking if a superblock already exists for the dataset, and in
that case we just need to return a new reference for the sb's
root dentry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Closes#5796Closes#7207
zfs_receive_raw_incremental did not clean up ibackup_trunc.* files
left over from running the test.
Also changing the path of the ibackup files so they can be placed
in the correct directories when /var/tmp is not the temporary
directory.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: bunder2015 <omfgbunder@gmail.com>
Closes#7430
This change adds five new tests to the ZTS:
* zpool_split_cliargs: verify command line options and arguments
* zpool_split_devices: verify zpool split accepts a device list
* zpool_split_encryption: verify zpool can split encrypted pools
* zpool_split_props: verify zpool split can set property values
* zpool_split_vdevs: verify vdev layout when splitting the pool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7409
calloc(3) takes `nelem` (or `nmemb` in glibc) first, and then size of
elements. No difference expected for having these in reverse order,
however should follow the standard.
http://pubs.opengroup.org/onlinepubs/009695399/functions/calloc.html
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7405
Authored by: Mike Gerdts <mike.gerdts@joyent.com>
Reviewed by: Allan Jude <allanjude@freebsd.org>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Andy Stormont <astormont@racktopsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Don Brady <don.brady@delphix.com>
Porting Notes:
* Adopted destroy_dataset in ZTS test cleanup
* Use ksh shebang instead of bash for new tests
OpenZFS-issue: https://www.illumos.org/issues/9286
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/723d0c85Closes#7387
Commit e4010f2 accidentally allows zpool to set pool features to
"disabled"; this should only be allowed at pool creation. This commit
adds additional checks and test coverage to 'zpool set'.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7402
This reverts commit cc63068e95.
Under certain circumstances this change can result in an ENOSPC
error when adding new files to a directory. See #7401 for full
details.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Issue #7401
Cloes #7416
Most kshlib files are imported by other scripts
and do not have a shebang at the top of their files.
Make all kshlib follow this convention.
Remove shebangs from cfg files as well.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Close#7406
Fedora 28's RPM build checks warn when executable files don't have a
shebang line. These warnings are caused when we (incorrectly)
include data & config files in the_SCRIPTS automake lines. Files in
_SCRIPTS are marked executable by automake. This patch fixes the
issue by including non-executable scripts in a _DATA line instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7359Closes#7395
Currently, "zfs mount -a" will print a warning and fail to mount
any encrypted datasets that do not have a key loaded. This patch
makes the behavior of this failure consistent with other failure
modes ("zfs mount -a" will silently continue, explict "zfs mount"
will print a message and return an error code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7382
When an MMP write is skipped, or fails, and time since
mts->mmp_last_write is already greater than mts->mmp_delay, increase
mts->mmp_delay. The original code only updated mts->mmp_delay when a
write succeeded, but this results in the write(s) after delays and
failed write(s) reporting an ub_mmp_delay which is too low.
Update mmp_last_write and mmp_delay if a txg sync was successful. At
least one uberblock was written, thus extending the time we can be sure
the pool will not be imported by another host.
Do not allow mmp_delay to go below (MSEC2NSEC(zfs_multihost_interval) /
vdev_count_leaves()) so that a period of frequent successful MMP writes,
e.g. due to frequent txg syncs, does not result in an import activity
check so short it is not reliable based on mmp thread writes alone.
Remove unnecessary local variable, start. We do not use the start time
of the loop iteration.
Add a debug message in spa_activity_check() to allow verification of the
import_delay value and to prove the activity check occurred.
Alter the tests that import pools and attempt to detect an activity
check. Calculate the expected duration of spa_activity_check() based on
module parameters at the time the import is performed, rather than a
fixed time set in mmp.cfg. The fixed time may be wrong. Also, use the
default zfs_multihost_interval value so the activity check is longer and
easier to recognize.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7330
Fix a bunch of (mostly) sprintf/snprintf truncation compiler
warnings that show up on Fedora 28 (GCC 8.0.1).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7361Closes#7368
Use 'zpool reopen' instead of 'zpool scrub' to kick in the spare device:
this is required to avoid spurious failures caused by a race condition
in events processing by the ZFS Event Daemon:
P1 (zpool scrub) P2 (zed)
---
zfs_ioc_pool_scan()
-> dsl_scan()
-> vdev_reopen()
-> vdev_set_state(VDEV_STATE_CANT_OPEN)
zfs_ioc_vdev_attach()
-> spa_vdev_attach()
-> dsl_resilver_restart()
-> dsl_sync_task()
-> dsl_scan_setup_check()
<- dsl_scan_setup_check(): EBUSY
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7247Closes#7342
Authored by: Andriy Gapon <avg@FreeBSD.org>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Don Brady <don.brady@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Porting Notes:
* Re-enabled and tweaked the zpool_upgrade_007_pos test case
to successfully run in under 5 minutes.
OpenZFS-issue: https://www.illumos.org/issues/9164
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/0e776dc06aCloses#6112Closes#7336
Calling uiomove() in mappedread() under the page lock can result
in a deadlock if the user space page needs to be faulted in.
Resolve the issue by dropping the page lock before the uiomove().
The inode range lock protects against concurrent updates via
zfs_read() and zfs_write().
Reviewed-by: Albert Lee <trisk@forkgnu.org>
Reviewed-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7335Closes#7339
RHEL/CentOS 6 supports sys/xattr.h eliminating the need for
libattr-devel as a dependency.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7344Closes#7351
The changes piggyback JSON output support on top of channel programs
(#6558). This way the JSON output support is targeted to scripting
use cases and is easily maintainable since it really only touches
one function (zfs_do_channel_program()).
This patch ports Joyent's JSON nvlist library from illumos to enable
easy JSON printing of channel program output nvlist. To keep the
delta small I also took advantage of the fact that printing in
zfs_do_channel_program() was almost always done before exiting
the program.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#7281
ZFS Performance test concurrency should be lowered for better latency
Work by Stephen Blinick.
Nightly performance runs typically consist of two levels of concurrency;
and both are fairly high.
Since the IO runs are to a ZFS filesystem, within a zpool, which is
based on some variable number of vdev's, the amount of IO driven to each
device is variable. Additionally, different device types (HDD vs SSD,
etc) can generally handle a different amount of concurrent IO before
saturating.
Nevertheless, in practice, it appears that most tests are well past the
concurrency saturation point and therefore both perform with the same
throughput, the maximum of the device. Because the queuedepth to the
device(s) is so high however, the latency is much higher than the best
possible at that throughput, and increases linearly with the increase in
concurrency.
This means that changes in code that impact latency during normal
operation (before saturation) may not be apparent when a large component
of the measured latency is from the IO sitting in a queue to be
serviced. Therefore, changing the concurrency settings is recommended
Authored by: Stephen Blinick <stephen.blinick@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: John Wren Kennedy <jwk404@gmail.com>
Ported-by: John Wren Kennedy <jwk404@gmail.com>
OpenZFS-issue: https://www.illumos.org/issues/9076
OpenZFS-commit: https://github.com/openzfs/openzfs/pull/562
Upstream bug: DLPX-45477
Closes#7302
Due to zpool create auto-partioning in Linux (i.e. sdb1),
certain utilities need to use the parition (sdb1) while
others use the whole disk name (sdb).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#6939Closes#7261
Change file related checks to use user namespaces and make
sure involved uids/gids are mappable in the current
namespace.
Note that checks without file ownership information will
still not take user namespaces into account, as some of
these should be handled via 'zfs allow' (otherwise root in a
user namespace could issue commands such as `zpool export`).
This also adds an initial user namespace regression test
for the setgid bit loss, with a user_ns_exec helper usable
in further tests.
Additionally, configure checks for the required user
namespace related features are added for:
* ns_capable
* kuid/kgid_has_mapping()
* user_ns in cred_t
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Closes#6800Closes#7270
The test could fail when attempting to write to a newly created
volume which was missing its device node. Resolve the issue by
calling block_device_wait() which blocks until udev creates the
needed entry.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7276Closes#7277
Implement a new helper within_tolerance to test if a value
is within range of a target.
Because the dbufstats and dbufs kstat file are being read
at slightly different times, it is possible for stats to be
slightly off. Use within_tolerance to determine if the value
is "close enough" to the target.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7239Closes#7266
Some usage patterns like send/recv of replication streams can
produce a large number of events. In such a case, the current
all-syslog.sh zedlet will hold up to its name, and flood the
logs with mostly redundant information. Two mitigate this
situation, this changeset introduces to new variables
ZED_SYSLOG_SUBCLASS_INCLUDE and ZED_SYSLOG_SUBCLASS_EXCLUDE
to zed.rc that give more control over which event classes end
up in the syslog.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Kobras <d.kobras@science-computing.de>
Closes#6886Closes#7260
Once per pass through the MMP thread's loop, the vdev tree is walked to
find a suitable leaf to write the next MMP block to. If no such leaf is
found, the thread sleeps for a while and resumes at the top of the loop.
Add an entry to multihost_history when no leaf can be found, and record
the reason in the error column. The error code for such entries is a
bitfield, displayed in hex:
0x1 At least one vdev (interior or leaf) was not writeable.
0x2 At least one writeable leaf vdev was found, but it had a pending
MMP write.
timestamp = the time in seconds since the epoch when no leaf could be
found originally.
duration = the time (in ns) during which no MMP block was written for
this reason. This does not include the preceeding inter-write period
nor the following inter-write period.
vdev_guid = the number of sequential cycles of the MMP thread looop when
this occurred.
Sample output, truncated to fit:
For records of skipped MMP writes the right-most column, vdev_path, is
reported as "-".
id txg timestamp error duration mmp_delay vdev_guid ...
936 11 1520036441 0 146264 891422313 1740883117838 ...
937 11 1520036441 0 163956 888356657 7320395061548 ...
938 11 1520036442 0 130690 885314969 7320395061548 ...
939 11 1520036442 0 2001068577 882296582 1740883117838 ...
940 11 1520036443 0 161806 882296582 7320395061548 ...
941 11 1520036443 0x2 0 998020546 1 ...
942 11 1520036444 0 136585 998020546 7320395061548 ...
943 11 1520036444 0x2 0 998020257 1 ...
944 11 1520036445 5 2002662964 994160219 1740883117838 ...
945 11 1520036445 0x2 998073118 994160219 3 ...
946 11 1520036447 0 247136 994160219 7320395061548 ...
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7212
Datasets can be busy when calling zfs destroy. Introduce
a helper function to destroy datasets and use it to destroy
datasets in zfs_allow_004_pos, zfs_promote_008_pos, and
zfs_destroy_002_pos.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#7224Closes#7246Closes#7249Closes#7267
Change checksum & IO delay ratelimit thresholds from 5/sec to 20/sec.
This allows zed to actually trigger if a bunch of these events arrive in
a short period of time (zed has a threshold of 10 events in 10 sec).
Previously, if you had, say, 100 checksum errors in 1 sec, it would get
ratelimited to 5/sec which wouldn't trigger zed to fault the drive.
Also, convert the checksum and IO delay thresholds to module params for
easy testing.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7252
The test could fail because of a race condition between the files being
generated in the background and attempting to move the files. Wait for
all file generation to complete before trying to move the files around.
Also, clean up the waiting: the 'wait' command without arguments waits
for all child pids.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Closes#7220Closes#7242Closes#7258
Tom Caputi
Olaf Faaland
Serapheim Dimitropoulos
bunder2015
Brian Behlendorf
LOLi
Paul Dagnelie
Matthew Ahrens
Serapheim Dimitropoulos
Serapheim Dimitropoulos
Ahmed Gahnem
Tim Chase
John Gallagher
Antonio Russo
Alek P
Tony Hutter
John Wren Kennedy
Sara Hartse
Tony Nguyen
George Melikov
Pavel Zakharov
loli10K
Chunwei Chen
Matt Ahrens
Toomas Soome
Seth Forshee
Tomohiro Kusumi
Mike Gerdts
Giuseppe Di Natale
Andriy Gapon
DeHackEd
Stephen Blinick
Paul Zuchowski
Wolfgang Bumiller
chrisrd