Commit Graph

143 Commits

Author SHA1 Message Date
Brian Behlendorf 2ae1031962 Linux 3.7 compat, schedule_delayed_work()
Linux kernel commit d8e794d accidentally broke the delayed work
APIs for non-GPL callers.   While the APIs to schedule a delayed
work item are still available to all callers, it is no longer
possible to initialize the delayed work item.

I'm cautiously optimistic we could get the delayed_work_timer_fn
exported for all callers in the upstream kernel.  But frankly
the compatibility code to use this kernel interface has always
been problematic.

Therefore, this patch abandons direct use the of the Linux
kernel interface in favor of the new delayed taskq interface.
It provides roughly the same functionality as delayed work queues
but it's a stable interface under our control.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #1053
2012-12-12 10:47:05 -08:00
Brian Behlendorf e89260a1c8 Directory xattr znodes hold a reference on their parent
Unlike normal file or directory znodes, an xattr znode is
guaranteed to only have a single parent.  Therefore, we can
take a refernce on that parent if it is provided at create
time and cache it.  Additionally, we take care to cache it
on any subsequent zfs_zaccess() where the parent is provided
as an optimization.

This allows us to avoid needing to do a zfs_zget() when
setting up the SELinux security xattr in the create path.
This is critical because a hash lookup on the directory
will deadlock since it is locked.

The zpl_xattr_security_init() call has also been moved up
to the zpl layer to ensure TXs to create the required
xattrs are performed after the create TX.  Otherwise we
run the risk of deadlocking on the open create TX.

Ideally the security xattr should be fully constructed
before the new inode is unlocked.  However, doing so would
require far more extensive changes to ZFS.

This change may also have the benefitial side effect of
ensuring xattr directory znodes are evicted from the cache
before normal file or directory znodes due to the extra
reference.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #671
2012-12-03 12:10:46 -08:00
Brian Behlendorf 30315d237b Increase ZFS_OBJ_MTX_SZ to 256
Increasing this limit costs us 6144 bytes of memory per mounted
filesystem, but this is small price to pay for accomplishing
the following:

* Allows for up to 256-way concurreny when performing lookups
  which helps performance when there are a large number of
  processes.

* Minimizes the likelyhood of encountering the deadlock
  described in issue #1101.  Because vmalloc() won't strictly
  honor __GFP_FS there is still a very remote chance of a
  deadlock.  See the zfsonlinux/spl@043f9b57 commit.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #1101
2012-11-27 13:46:32 -08:00
Brian Behlendorf 2404b01499 Improve AF hard disk detection
Use the bdev_physical_block_size() interface to determine the
minimize write size which can be issued without incurring a
read-modify-write operation.  This is used to set the ashift
correctly to prevent a performance penalty when using AF hard
disks.

Unfortunately, this interface isn't entirely reliable because
it's not uncommon for disks to misreport this value.  For this
reason you may still need to manually set your ashift with:

  zpool create -o ashift=12 ...

The solution to this in the upstream Illumos source was to add
a white list of known offending drives.  Maintaining such a list
will be a burden, but it still may be worth doing if we can
detect a large number of these drives.  This should be considered
as future work.

Reported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #916
2012-11-15 11:06:14 -08:00
George Wilson 32a9872bba Illumos #2671: zpool import should not fail if vdev ashift has increased
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Richard Lowe <richlowe@richlowe.net>

Refererces to Illumos issue:
      https://www.illumos.org/issues/2671

This patch has been slightly modified from the upstream Illumos
version.  In the upstream implementation a warning message is
logged to the console.  To prevent pointless console noise this
notification is now posted as a "ereport.fs.zfs.vdev.bad_ashift"
event.

The event indicates a non-optimial (but entirely safe) ashift
value was used to create the pool.  Depending on your workload
this may impact pool performance.  Unfortunately, the only way
to correct the issue is to recreate the pool with a new ashift.

NOTE: The unrelated fix to the comment in zpool_main.c appears
in the upstream commit and was preserved for consistnecy.

Ported-by: Cyril Plisko <cyril.plisko@mountall.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #955
2012-11-15 11:05:59 -08:00
Brian Behlendorf 9dcb971983 Log I/Os longer than zio_delay_max (30s default)
There have been reports of ZFS deadlocking due to what appears to
be a lost IO.  This patch addes some debugging to determine the
exact state of the IO which neither 1) completed, 2) failed, or
3) timed out after zio_delay_max (30) seconds.

This information will be logged using the ZFS FMA infrastructure
as a 'delay' event and posted to the internal zevent log.  By
default the last 64 events will be kept in the log but the limit
is configurable via the zfs_zevent_len_max module option.

To dump the contents of the log use the 'zpool events -v' command
and look for the resource.fs.zfs.delay event.  It will include
various information about the pool, vdev, and zio which may shed
some light on the issue.

In the context of this change the 120 second kernel blocked thread
watchdog has been disabled for synchronous IOs.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #930
2012-11-02 15:45:59 -07:00
Brian Behlendorf e95853a331 Add txgs-<pool> kstat file
Create a kstat file which contains useful statistics about the
last N txgs processed.  This can be helpful when analyzing pool
performance.  The new KSTAT_TYPE_TXG type was added for this
purpose and it tracks the following statistics per-txg.

  txg          - Unique txg number
  state        - State (O)pen/(Q)uiescing/(S)yncing/(C)ommitted
  birth;       - Creation time
  nread        - Bytes read
  nwritten;    - Bytes written
  reads        - IOPs read
  writes       - IOPs write
  open_time;   - Length in nanoseconds the txg was open
  quiesce_time - Length in nanoseconds the txg was quiescing
  sync_time;   - Length in nanoseconds the txg was syncing

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-11-02 15:45:56 -07:00
Brian Behlendorf e8fd45a0f9 Add ddt_object_count() error handling
The interface for the ddt_zap_count() function assumes it can
never fail.  However, internally ddt_zap_count() is implemented
with zap_count() which can potentially fail.  Now because there
was no way to return the error to the caller a VERIFY was used
to ensure this case never happens.

Unfortunately, it has been observed that pools can be damaged in
such a way that zap_count() fails.  The result is that the pool can
not be imported without hitting the VERIFY and crashing the system.

This patch reworks ddt_object_count() so the error can be safely
caught and returned to the caller.  This allows a pool which has
be damaged in this way to be safely rewound for import.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #910
2012-10-29 08:57:45 -07:00
Brian Behlendorf eac4720465 Allow 'zpool replace' to use short device names
The 'zpool replace' command would fail when given a short name
because unlike on other platforms the short name cannot be
deterministically expanded to a single path.  Multiple path
prefixes must be checked and in addition the partition suffix
for whole disks is determined by the prefix.

To handle this complexity a zfs_strcmp_pathname() function was
added which takes either a short or fully qualified device name.
Short names will be expanded using the prefixes in the default
import search path, or the ZPOOL_IMPORT_PATH environment variable
if it's defined.  All posible expansions are then compared against
the comparison path.  Care is taken to strip redundant slashes to
ensure legitimate matches are not missed.

In the context of this work the existing zfs_resolve_shortname()
function was extended to consider the ZPOOL_IMPORT_PATH when set.
The zfs_append_partition() interface was also simplified to take
only a single buffer.

The vast majority of these changes rework existing Linux specific
code which was originally written to accomidate udev.  However,
there is some minimal cleanup which removes Illumos specific code.
This was done to improve readability but the basic flow and intent
of the upstream code was maintained.

These changes are the logical conclusion of the previos work to
adjust the 'zpool import' search behavior, see commit 44867b6a.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #544
Closes #976
2012-10-22 08:45:58 -07:00
Etienne Dechamps 920dd524fb Add FASTWRITE algorithm for synchronous writes.
Currently, ZIL blocks are spread over vdevs using hint block pointers
managed by the ZIL commit code and passed to metaslab_alloc(). Spreading
log blocks accross vdevs is important for performance: indeed, using
mutliple disks in parallel decreases the ZIL commit latency, which is
the main performance metric for synchronous writes. However, the current
implementation suffers from the following issues:

1) It would be best if the ZIL module was not aware of such low-level
details. They should be handled by the ZIO and metaslab modules;

2) Because the hint block pointer is managed per log, simultaneous
commits from multiple logs might use the same vdevs at the same time,
which is inefficient;

3) Because dmu_write() does not honor the block pointer hint, indirect
writes are not spread.

The naive solution of rotating the metaslab rotor each time a block is
allocated for the ZIL or dmu_sync() doesn't work in practice because the
first ZIL block to be written is actually allocated during the previous
commit. Consequently, when metaslab_alloc() decides the vdev for this
block, it will do so while a bunch of other allocations are happening at
the same time (from dmu_sync() and other ZILs). This means the vdev for
this block is chosen more or less at random. When the next commit
happens, there is a high chance (especially when the number of blocks
per commit is slightly less than the number of the disks) that one disk
will have to write two blocks (with a potential seek) while other disks
are sitting idle, which defeats spreading and increases the commit
latency.

This commit introduces a new concept in the metaslab allocator:
fastwrites. Basically, each top-level vdev maintains a counter
indicating the number of synchronous writes (from dmu_sync() and the
ZIL) which have been allocated but not yet completed. When the metaslab
is called with the FASTWRITE flag, it will choose the vdev with the
least amount of pending synchronous writes. If there are multiple vdevs
with the same value, the first matching vdev (starting from the rotor)
is used. Once metaslab_alloc() has decided which vdev the block is
allocated to, it updates the fastwrite counter for this vdev.

The rationale goes like this: when an allocation is done with
FASTWRITE, it "reserves" the vdev until the data is written. Until then,
all future allocations will naturally avoid this vdev, even after a full
rotation of the rotor. As a result, pending synchronous writes at a
given point in time will be nicely spread over all vdevs. This contrasts
with the previous algorithm, which is based on the implicit assumption
that blocks are written instantaneously after they're allocated.

metaslab_fastwrite_mark() and metaslab_fastwrite_unmark() are used to
manually increase or decrease fastwrite counters, respectively. They
should be used with caution, as there is no per-BP tracking of fastwrite
information, so leaks and "double-unmarks" are possible. There is,
however, an assert in the vdev teardown code which will fire if the
fastwrite counters are not zero when the pool is exported or the vdev
removed. Note that as stated above, marking is also done implictly by
metaslab_alloc().

ZIO also got a new FASTWRITE flag; when it is used, ZIO will pass it to
the metaslab when allocating (assuming ZIO does the allocation, which is
only true in the case of dmu_sync). This flag will also trigger an
unmark when zio_done() fires.

A side-effect of the new algorithm is that when a ZIL stops being used,
its last block can stay in the pending state (allocated but not yet
written) for a long time, polluting the fastwrite counters. To avoid
that, I've implemented a somewhat crude but working solution which
unmarks these pending blocks in zil_sync(), thus guaranteeing that
linguering fastwrites will get pruned at each sync event.

The best performance improvements are observed with pools using a large
number of top-level vdevs and heavy synchronous write workflows
(especially indirect writes and concurrent writes from multiple ZILs).
Real-life testing shows a 200% to 300% performance increase with
indirect writes and various commit sizes.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1013
2012-10-17 08:56:41 -07:00
Richard Yao 95f5c63b47 Linux 3.6 compat, iops->mkdir()
Use .mkdir instead of .create in 3.3 compatibility check.  Linux 3.6
modifies inode_operations->create's function prototype. This causes
an autotools Linux 3.3. compatibility check for a function prototype
change in create, mkdir and mknode to fail. Since mkdir and mknode
are unchanged, we modify the check to examine it instead.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #873
2012-10-14 15:29:26 -07:00
Yuxuan Shui 3c20361075 Linux 3.6 compat, sget()
As of Linux commit 9249e17fe094d853d1ef7475dd559a2cc7e23d42 the
mount flags are now passed to sget() so they can be used when
initializing a new superblock.

ZFS never uses sget() in this fashion so we can simply pass a
zero and add a zpl_sget() compatibility wrapper.

Signed-off-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #873
2012-10-14 13:06:48 -07:00
Brian Behlendorf 87d98efe9e Fix zfs_txg_timeout module parameter
Allow the zfs_txg_timeout variable to be dynamically tuned at run
time.  By pulling it down out of the variable declaration it will
be evaluted each time through the loop.

The zfs_txg_timeout variable is now declared extern in a the common
sys/txg.h header rather than locally in dsl_scan.c.  This prevents
potential type mismatches if the global variable needs to be used
elsewhere.

Move the module_param() code in to the same source file where
zfs_txg_timeout is declared.  This is the most logical location.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-10-11 15:07:09 -07:00
Richard Yao 7df05a4266 Fix zfs_write_limit_max integer size mismatch on 32-bit systems
Commit c409e4647f introduced a
number of module parameters.  This required several types to be
changed to accomidate the required module parameters Linux macros.

Unfortunately, arc.c contained its own extern definition of the
zfs_write_limit_max variable and its type was not updated to be
consistent with its dsl_pool.c counterpart.  If the variable had
been properly marked extern in a common header, then gcc would
have generated a warning and this would not have slipped through.

The result of this was that the ARC unconditionally expected
zfs_write_limit_max to be 64-bit. Unfortunately, the largest size
integer module parameter that Linux supports is unsigned long, which
varies in size depending on the host system's native word size. The
effect was that on 32-bit systems, ARC incorrectly performed 64-bit
operations on a 32-bit value by reading the neighboring 32 bits as
the upper 32 bits of the 64-bit value.

We correct that by changing the extern declaration to use the unsigned
long type and move these extern definitions in to the common arc.h
header. This should make ARC correctly treat zfs_write_limit_max as a
32-bit value on 32-bit systems.

Reported-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #749
2012-10-11 11:09:25 -07:00
Matthew Ahrens 04434775b7 Illumos #3100: zvol rename fails with EBUSY when dirty.
illumos/illumos-gate@2e2c135528
Illumos changeset: 13780:6da32a929222

3100 zvol rename fails with EBUSY when dirty

Reviewed by: Christopher Siden <chris.siden@delphix.com>
Reviewed by: Adam H. Leventhal <ahl@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>

Ported-by: Etienne Dechamps <etienne.dechamps@ovh.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #995
2012-10-03 13:59:02 -07:00
Etienne Dechamps 274091c074 Fix VOP_CLOSE() in userspace.
Currently, for unknown reasons, VOP_CLOSE() is a no-op in userspace.
This causes file descriptor leaks. This is especially problematic with
long ztest runs, since zpool.cache is opened repeatedly and never
closed, resulting in resource exhaustion (EMFILE errors).

This patch fixes the issue by making VOP_CLOSE() do what it is supposed
to do.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
2012-10-03 13:32:48 -07:00
Etienne Dechamps 0aebd4f9e3 Create threads in detached state in userspace.
Currently, thread_create(), when called in userspace, creates a
joinable (i.e. not detached thread). This is the pthread default.

Unfortunately, this does not reproduce kthreads behavior (kthreads
are always detached). In addition, this contradicts the original
Solaris code which creates userspace threads in detached mode.

These joinable threads are never joined, which leads to a leakage of
pthread thread objects ("zombie threads"). This in turn results in
excessive ressource consumption, and possible ressource exhaustion in
extreme cases (e.g. long ztest runs).

This patch fixes the issue by creating userspace threads in detached
mode. The only exception is ztest worker threads which are meant to be
joinable.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #989
2012-10-03 13:32:48 -07:00
Bill Pijewski 37abac6d55 Illumos #2703: add mechanism to report ZFS send progress
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>

References:
  https://www.illumos.org/issues/2703

Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-09-19 13:39:06 -07:00
Chris Siden 1bd201e70d Illumos #1948: zpool list should show more detailed pool info
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>

References:
  https://www.illumos.org/issues/1948

Ported by:	Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #685
2012-09-19 13:39:05 -07:00
Brian Behlendorf cda4db408c Revert "Improve AF hard disk detection"
This reverts commit 395350c85d which
accidentally introduced issue #955.

Pools using AF drives which were originally created with a sector
size of 512 bytes will now be correctly detected to have physical
sector size of 4096.  This is desirable for a new pool, however for
an existing pool abruptly changing the sector size causes problems.

For this reason, this change is being reverted until the additional
logic can be added to detect the existing pool case.  Existing
pools must use the ashift size stored in the label regardless of
what the disk reports.  This is critical for compatibility.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #955
2012-09-11 16:33:49 -07:00
Brian Behlendorf 0ef0ff546e Switch KM_SLEEP to KM_PUSHPAGE
This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim.  See commit b8d06fca08
for additional details.

  SPL: Fixing allocation for task txg_sync (6093) which
  used GFP flags 0x297bda7c with PF_NOFS set

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
2012-09-04 16:00:06 -07:00
Brian Behlendorf 395350c85d Improve AF hard disk detection
Use the bdev_physical_block_size() interface to determine the
minimize write size which can be issued without incurring a
read-modify-write operation.  This is used to set the ashift
correctly to prevent a performance penalty when using AF hard
disks.

Unfortunately, this interface isn't entirely reliable because
it's not uncommon for disks to misreport this value.  For this
reason you may still need to manually set your ashift with:

  zpool create -o ashift=12 ...

The solution to this in the upstream Illumos source was to add
a while list of known offending drives.  Maintaining such a list
will be a burden, but it still may be worth doing if we can
detect a large number of these drives.  This should be considered
as future work.

Reported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #916
2012-09-04 15:35:32 -07:00
Richard Yao b8d06fca08 Switch KM_SLEEP to KM_PUSHPAGE
Differences between how paging is done on Solaris and Linux can cause
deadlocks if KM_SLEEP is used in any the following contexts.

  * The txg_sync thread
  * The zvol write/discard threads
  * The zpl_putpage() VFS callback

This is because KM_SLEEP will allow for direct reclaim which may result
in the VM calling back in to the filesystem or block layer to write out
pages.  If a lock is held over this operation the potential exists to
deadlock the system.  To ensure forward progress all memory allocations
in these contexts must us KM_PUSHPAGE which disables performing any I/O
to accomplish the memory allocation.

Previously, this behavior was acheived by setting PF_MEMALLOC on the
thread.  However, that resulted in unexpected side effects such as the
exhaustion of pages in ZONE_DMA.  This approach touchs more of the zfs
code, but it is more consistent with the right way to handle these cases
under Linux.

This is patch lays the ground work for being able to safely revert the
following commits which used PF_MEMALLOC:

  21ade34 Disable direct reclaim for z_wr_* threads
  cfc9a5c Fix zpl_writepage() deadlock
  eec8164 Fix ASSERTION(!dsl_pool_sync_context(tx->tx_pool))

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
2012-08-27 12:01:37 -07:00
Brian Behlendorf 86dd0fd922 Pre-allocate vdev I/O buffers
The vdev queue layer may require a small number of buffers
when attempting to create aggregate I/O requests.  Rather than
attempting to allocate them from the global zio buffers, which
is slow under memory pressure, it makes sense to pre-allocate
them because...

1) These buffers are short lived.  They are only required for
the life of a single I/O at which point they can be used by
the next I/O.

2) The maximum number of concurrent buffers needed by a vdev is
small.  It's roughly limited by the zfs_vdev_max_pending tunable
which defaults to 10.

By keeping a small list of these buffer per-vdev we can ensure
one is always available when we need it.  This significantly
reduces contention on the vq->vq_lock, because we no longer
need to perform a slow allocation under this lock.  This is
particularly important when memory is already low on the system.

It would probably be wise to extend the use of these buffers beyond
aggregate I/O and in to the raidz implementation.  The inability
to quickly allocate buffer for the parity stripes could result in
similiar problems.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-08-27 12:01:37 -07:00
Richard Yao 44f21da41c Revert Disable direct reclaim for z_wr_* threads
This commit used PF_MEMALLOC to prevent a memory reclaim deadlock.
However, commit 49be0ccf1f eliminated
the invocation of __cv_init(), which was the cause of the deadlock.
PF_MEMALLOC has the side effect of permitting pages from ZONE_DMA
to be allocated.  The use of PF_MEMALLOC was found to cause stability
problems when doing swap on zvols. Since this technique is known to
cause problems and no longer fixes anything, we revert it.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
2012-08-27 12:01:37 -07:00
Brian Behlendorf ca8b5af89d Remove autotools products
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #718
2012-08-27 11:47:44 -07:00
Prakash Surya 15a9e03368 Wrap smp_processor_id in kpreempt_[dis|en]able
After surveying the code, the few places where smp_processor_id is used
were deemed to be safe to use with a preempt enabled kernel. As such, no
core logic had to be changed. These smp_processor_id call sites are simply
are wrapped in kpreempt_disable and kpreempt_enabled to prevent the
Linux kernel from emitting scary warnings.

Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Issue #83
2012-08-24 13:19:06 -07:00
Eric Schrock db49968e5c Illumos #2635: 'zfs rename -f' to perform force unmount
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Richard Lowe <richlowe@richlowe.net>

References:
  https://www.illumos.org/issues/2635

Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #717
2012-08-23 10:39:43 -07:00
Brian Behlendorf 8f576c2321 Export dbuf_* symbols
Export these symbols so they may be used by other ZFS consumers
besides the ZPL.

Remove three stale prototype definites from dbuf.h.  The actual
implementations of these functions were removed/renamed long ago.

It would be good in the long term to remove the existing pragmas
we inherited from Solaris and simply use the dbuf_* names.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-08-10 16:45:13 -07:00
Dan McDonald d96eb2b153 Illumos #1693: persistent 'comment' field for a zpool
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>

References:
  https://www.illumos.org/issues/1693

Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #678
2012-08-08 11:49:37 -07:00
Etienne Dechamps ee5fd0bb80 Set zvol discard_granularity to the volblocksize.
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.

In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).

With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #862
2012-08-07 14:55:31 -07:00
Matthew Ahrens 330d06f90d Illumos #1644, #1645, #1646, #1647, #1708
1644 add ZFS "clones" property
1645 add ZFS "written" and "written@..." properties
1646 "zfs send" should estimate size of stream
1647 "zfs destroy" should determine space reclaimed by
     destroying multiple snapshots
1708 adjust size of zpool history data

References:
  https://www.illumos.org/issues/1644
  https://www.illumos.org/issues/1645
  https://www.illumos.org/issues/1646
  https://www.illumos.org/issues/1647
  https://www.illumos.org/issues/1708

This commit modifies the user to kernel space ioctl ABI.  Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated.  This change has reordered
all of the new ioctl()s to the end of the list.  This should
help minimize this issue in the future.

Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Albert Lee <trisk@opensolaris.org>
Approved by: Garrett D'Amore <garret@nexenta.com>

Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #826
Closes #664
2012-07-31 09:25:30 -07:00
Richard Yao 739a1a82e0 Linux 3.5 compat, end_writeback() changed to clear_inode()
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict().   This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.

However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics.  This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #784
2012-07-23 12:29:36 -07:00
Richard Yao ea1fdf46e2 Linux 3.5 compat, iops->truncate_range() removed
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
2012-07-23 12:29:32 -07:00
Richard Yao 756c3e5a9c Linux 3.5 compat, eops->encode_fh() takes inodes
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes.  This interface used to
take the child dentry and a bool describing if the parent is needed.

NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
2012-07-23 12:29:23 -07:00
Richard Yao 0a6b03d3b8 Fix build failures on PaX/GRSecurity patched kernels
Gentoo Hardened kernels include the PaX/GRSecurity patches. They use a
dialect of C that relies on a GCC plugin. In particular, struct
file_operations has been marked do_const in the PaX/GRSecurity dialect,
which causes GCC to consider all instances of it as const. This caused
failures in the autotools checks and the ZFS source code.

To address this, we modify the autotools checks to take into account
differences between the PaX C dialect and the regular C dialect. We also
modify struct zfs_acl's z_ops member to be a pointer to a function
pointer table. Lastly, we modify zpl_put_link() to address a PaX change
to the function prototype of nd_get_link().  This avoids compiler errors
in the PaX/GRSecurity dialect.

Note that the change in zpl_put_link() causes a warning that becomes a
build failure when debugging is enabled. Fixing that warning requires
ryao/spl@5ca50ef459.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #484
2012-07-17 09:22:43 -07:00
Etienne Dechamps b5a28807cd Move partition scanning from userspace to module.
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.

This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.

Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.

This change also depends on API changes which are available in 2.6.37
and latter kernels.  The build system has been updated to detect this,
but there is no compatibility mode for older kernels.  This means that
online expansion will NOT be available in older kernels.  However, it
will still be possible to expand the vdev offline.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #808
2012-07-17 09:17:31 -07:00
George Wilson c7f2d69de3 Illumos #1949, #1953
1949 crash during reguid causes stale config
1953 allow and unallow missing from zpool history since removal of pyzfs

Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Garrett D'Amore <garrett.damore@gmail.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Steve Gonczi <gonczi@comcast.net>
Approved by: Eric Schrock <eric.schrock@delphix.com>

References:
  https://www.illumos.org/issues/1949
  https://www.illumos.org/issues/1953

Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #665
2012-07-11 13:33:31 -07:00
Garrett D'Amore 3541dc6d02 Illumos #1748: desire support for reguid in zfs
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>

References:
  https://www.illumos.org/issues/1748

This commit modifies the user to kernel space ioctl ABI.  Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated.  If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.

Ported by:     Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #665
2012-07-11 13:08:56 -07:00
Richard Yao a3873583c2 Use ULL suffix in constants
The lack of the ULL suffix causes warnings such as the following on
32-bit systems:

  In function 'zfsctl_is_snapdir':
  zfs-0.6.0//module/zfs/zfs_ctldir.c:151: warning: integer constant
  is too large for 'long' type

We add the ULL suffix to fix that.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #813
2012-07-10 11:31:55 -07:00
Etienne Dechamps b6ad9671ac Add ZIL statistics.
The performance of the ZIL is usually the main bottleneck when dealing with
synchronous, write-heavy workloads (e.g. databases). Understanding the
behavior of the ZIL is required to diagnose performance issues for these
workloads, and to tune ZIL parameters (like zil_slog_limit) accordingly.

This commit adds a new kstat page dedicated to the ZIL with some counters
which, hopefully, scheds some light into what the ZIL is doing, and how it is
doing it.

Currently, these statistics are available in /proc/spl/kstat/zfs/zil.
A description of the fields can be found in zil.h.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #786
2012-06-29 09:56:51 -07:00
Pawel Jakub Dawidek 0cee24064a Speed up 'zfs list -t snapshot -o name -s name'
FreeBSD #xxx:  Dramatically optimize listing snapshots when user
requests only snapshot names and wants to sort them by name, ie.
when executes:

  # zfs list -t snapshot -o name -s name

Because only name is needed we don't have to read all snapshot
properties.

Below you can find how long does it take to list 34509 snapshots
from a single disk pool before and after this change with cold and
warm cache:

    before:

        # time zfs list -t snapshot -o name -s name > /dev/null
        cold cache: 525s
        warm cache: 218s

    after:

        # time zfs list -t snapshot -o name -s name > /dev/null
        cold cache: 1.7s
        warm cache: 1.1s

NOTE: This patch only appears in FreeBSD.  If/when Illumos picks up
the change we may want to drop this patch and adopt their version.
However, for now this addresses a real issue.

Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #450
2012-06-14 09:49:04 -07:00
Richard Yao 6a0936babc Linux 3.4 compat, d_make_root() replaces d_alloc_root()
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:

  error: implicit declaration of function 'd_alloc_root'
  [-Werror=implicit-function-declaration]

To correct this we update the code to use the current d_make_root()
interface for readability.  Then we introduce an autotools check
to determine if d_make_root() is available.  If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.

Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #776
2012-06-11 10:04:49 -07:00
Brian Behlendorf b39d3b9f7b Linux 3.3 compat, iops->create()/mkdir()/mknod()
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'.  To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef.  There is no functional change.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #701
2012-04-30 12:52:38 -07:00
George Wilson 5ffb9d1d05 Illumos #1951: leaking a vdev when removing an l2cache device
1952 memory leak when adding a file-based l2arc device
1954 leak in ZFS from metaslab_group_create and zfs_ereport_checksum

Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Approved by: Eric Schrock <eric.schrock@delphix.com>

References to Illumos issues:
  https://www.illumos.org/issues/1951
  https://www.illumos.org/issues/1952
  https://www.illumos.org/issues/1954

Ported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #650
2012-04-11 11:32:06 -07:00
Brian Behlendorf 1c5de20ae2 Add --enable-debug-dmu-tx configure option
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging.  When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.

This checking is particularly helpful when adding new dmu consumers
like Lustre.  However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.

--enable-debug-dmu-tx  - Enable/disable validation of each tx as
--disable-debug-dmu-tx   it is constructed.  By default validation
                         is disabled due to performance concerns.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-03-23 12:25:17 -07:00
Brian Behlendorf ebe7e575ea Add .zfs control directory
Add support for the .zfs control directory.  This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required.  The bulk of the core
functionality is now all there with the following limitations.

*) The .zfs/snapshot directory automount support requires a 2.6.37
   or newer kernel.  The exception is RHEL6.2 which has backported
   the d_automount patches.

*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
   in the .zfs/snapshot directory works as expected.  However,
   this functionality is only available to root until zfs
   delegations are finished.

      * mkdir - create a snapshot
      * rmdir - destroy a snapshot
      * mv    - rename a snapshot

The following issues are known defeciences, but we expect them to
be addressed by future commits.

*) Add automount support for kernels older the 2.6.37.  This should
   be possible using follow_link() which is what Linux did before.

*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
   The majority of the ground work for this is complete.  However,
   finishing this work will require resolving some lingering
   integration issues with the Linux NFS kernel server.

*) The .zfs/shares directory exists but no futher smb functionality
   has yet been implemented.

Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes #173
2012-03-22 13:03:47 -07:00
Brian Behlendorf 0ece356db5 Add sa_spill_rele() interface
Add a SA interface which allows us to release the spill block
from a SA handle without destroying the handle.  This is useful
because we can then ensure that a copy of the dirty spill block
is not made at sync time due to the extra hold.  Susequent calls
to sa_update() or sa_lookup() with transparently refetch the
spill block dbuf from the ARC hash.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-03-07 16:28:00 -08:00
Brian Behlendorf 4b787d75c8 Cleanly support debug packages
Allow a source rpm to be rebuilt with debugging enabled.  This
avoids the need to have to manually modify the spec file.  By
default debugging is still largely disabled.  To enable specific
debugging features use the following options with rpmbuild.

  '--with debug'               - Enables ASSERTs

  # For example:
  $ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm

Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers.  This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-02-27 14:08:17 -08:00
Brian Behlendorf 570827e129 Add 'dmu_tx' kstats entry
Keep counters for the various reasons that a thread may end up
in txg_wait_open() waiting on a new txg.  This can be useful
when attempting to determine why a particular workload is
under performing.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-02-27 08:59:10 -08:00