Linux 6.2 changes the second argument of the set_acl operation to be a
"struct dentry *" rather than a "struct inode *". The inode* parameter
is still available as dentry->d_inode, so adjust the call to the _impl
function call to dereference and pass that pointer to it.
Also document that the get_acl -> get_inode_acl member name change from
commit 884a693 was an API change also introduced in Linux 6.2.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14415
In original code, zfs_znode_dmu_fini is called in zfs_rmnode without
zfs_znode_hold_enter. It seems to assume it's ok to do so when the znode
is unlinked. However this assumption is not correct, as zfs_zget can be
called by NFS through zpl_fh_to_dentry as pointed out by Christian in
https://github.com/openzfs/zfs/pull/12767, which could result in a
use-after-free bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12767Closes#14364
I recently gained the ability to run Clang's static analyzer on the
linux kernel modules via a few hacks. This extended coverage to code
that was previously missed since Clang's static analyzer only looked at
code that we built in userspace. Running it against the Linux kernel
modules built from my local branch produced a total of 72 reports
against my local branch. Of those, 50 were reports of logic errors and
22 were reports of dead code. Since we already had cleaned up all of
the previous dead code reports, I felt it would be a good next step to
clean up these dead code reports. Clang did a further breakdown of the
dead code reports into:
Dead assignment 15
Dead increment 2
Dead nested assignment 5
The benefit of cleaning these up, especially in the case of dead nested
assignment, is that they can expose places where our error handling is
incorrect. A number of them were fairly straight forward. However
several were not:
In vdev_disk_physio_completion(), not only were we not using the return
value from the static function vdev_disk_dio_put(), but nothing used it,
so I changed it to return void and removed the existing (void) cast in
the other area where we call it in addition to no longer storing it to a
stack value.
In FSE_createDTable(), the function is dead code. Its helper function
FSE_freeDTable() is also dead code, as are the CPP definitions in
`module/zstd/include/zstd_compat_wrapper.h`. We just delete it all.
In zfs_zevent_wait(), we have an optimization opportunity. cv_wait_sig()
returns 0 if there are waiting signals and 1 if there are none. The
Linux SPL version literally returns `signal_pending(current) ? 0 : 1)`
and FreeBSD implements the same semantics, we can just do
`!cv_wait_sig()` in place of `signal_pending(current)` to avoid
unnecessarily calling it again.
zfs_setattr() on FreeBSD version did not have error handling issue
because the code was removed entirely from FreeBSD version. The error is
from updating the attribute directory's files. After some thought, I
decided to propapage errors on it to userspace.
In zfs_secpolicy_tmp_snapshot(), we ignore a lack of permission from the
first check in favor of checking three other permissions. I assume this
is intentional.
In zfs_create_fs(), the return value of zap_update() was not checked
despite setting an important version number. I see no backward
compatibility reason to permit failures, so we add an assertion to catch
failures. Interestingly, Linux is still using ASSERT(error == 0) from
OpenSolaris while FreeBSD has switched to the improved ASSERT0(error)
from illumos, although illumos has yet to adopt it here. ASSERT(error ==
0) was used on Linux while ASSERT0(error) was used on FreeBSD since the
entire file needs conversion and that should be the subject of
another patch.
dnode_move()'s issue was caused by us not having implemented
POINTER_IS_VALID() on Linux. We have a stub in
`include/os/linux/spl/sys/kmem_cache.h` for it, when it really should be
in `include/os/linux/spl/sys/kmem.h` to be consistent with
Illumos/OpenSolaris. FreeBSD put both `POINTER_IS_VALID()` and
`POINTER_INVALIDATE()` in `include/os/freebsd/spl/sys/kmem.h`, so we
copy what it did.
Whenever a report was in platform-specific code, I checked the FreeBSD
version to see if it also applied to FreeBSD, but it was only relevant a
few times.
Lastly, the patch that enabled Clang's static analyzer to be run on the
Linux kernel modules needs more work before it can be put into a PR. I
plan to do that in the future as part of the on-going static analysis
work that I am doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14380
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/null/badzero.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
In zfs_zaccess_dataset_check(), we have the following subexpression:
(!IS_DEVVP(ZTOV(zp)) ||
(IS_DEVVP(ZTOV(zp)) && (v4_mode & WRITE_MASK_ATTRS)))
When !IS_DEVVP(ZTOV(zp)) is false, IS_DEVVP(ZTOV(zp)) is true under the
law of the excluded middle since we are not doing pseudoboolean alegbra.
Therefore doing:
(IS_DEVVP(ZTOV(zp)) && (v4_mode & WRITE_MASK_ATTRS))
Is unnecessary and we can just do:
(v4_mode & WRITE_MASK_ATTRS)
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/excluded_middle.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
However, unlike the cases where the GNU zero length array extension had
been used, coccicheck would not suggest patches for the older style
single member arrays. That was good because blindly changing them would
break size calculations in most cases.
Therefore, this required care to make sure that we did not break size
calculations. In the case of `indirect_split_t`, we use
`offsetof(indirect_split_t, is_child[is->is_children])` to calculate
size. This might be subtly wrong according to an old mailing list
thread:
https://inbox.sourceware.org/gcc-prs/20021226123454.27019.qmail@sources.redhat.com/T/
That is because the C99 specification should consider the flexible array
members to start at the end of a structure, but compilers prefer to put
padding at the end. A suggestion was made to allow compilers to allocate
padding after the VLA like compilers already did:
http://std.dkuug.dk/JTC1/SC22/WG14/www/docs/n983.htm
However, upon thinking about it, whether or not we allocate end of
structure padding does not matter, so using offsetof() to calculate the
size of the structure is fine, so long as we do not mix it with sizeof()
on structures with no array members.
In the case that we mix them and padding causes offsetof(struct_t,
vla_member[0]) to differ from sizeof(struct_t), we would be doing unsafe
operations if we underallocate via `offsetof()` and then overcopy via
sizeof().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
fdc2d30371 accidentally broke the
indentation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic
patch that caught it was:
./scripts/coccinelle/misc/flexible_array.cocci
The Linux kernel's documentation makes a good case for why we should not
use these:
https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught this. The semantic patch
that caught it was:
./scripts/coccinelle/api/alloc/zalloc-simple.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The Linux 5.16.14 kernel's coccicheck caught these. The semantic patch
that caught them was:
./scripts/coccinelle/api/alloc/alloc_cast.cocci
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14372
The default_bs and default_ibs tunables control the default block size
and indirect block size.
So far, default_bs and default_ibs were tunable only on FreeBSD, e.g.,
sysctl vfs.zfs.default_ibs
Remove the FreeBSD-specific sysctl code and expose default_bs and
default_ibs as tunables on both Linux and FreeBSD using
ZFS_MODULE_PARAM.
One of the use cases for changing the values of those tunables is to
lower the indirect block size, which may improve performance of large
directories (as discussed during the OpenZFS Leadership Meeting
on 2022-08-16).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Wasabi Technology, Inc.
Closes#14293
Linux 6.2 renamed the get_acl() operation to get_inode_acl() in
the inode_operations struct. This should fix Issue #14323.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14323Closes#14331
Linux 863f144 modified the .tmpfile interface to pass a struct file,
rather than a struct dentry, and expect the tmpfile implementation to
open inside of tmpfile().
This patch implements a configuration test that checks for this new API
and appropriately sets a HAVE_TMPFILE_DENTRY flag that tracks this old
API. Contingent on this flag, the appropriate API is implemented.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#14301Closes#14343
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#14328
Previously the primarycache property was handled only in the dbuf
layer. Since the speculative prefetcher is implemented in the ARC,
it had to be disabled for uncacheable buffers.
This change gives the ARC knowledge about uncacheable buffers
via arc_read() and arc_write(). So when remove_reference() drops
the last reference on the ARC header, it can either immediately destroy
it, or if it is marked as prefetch, put it into a new arc_uncached state.
That state is scanned every second, evicting stale buffers that were
not demand read.
This change also tracks dbufs that were read from the beginning,
but not to the end. It is assumed that such buffers may receive further
reads, and so they are stored in dbuf cache. If a following
reads reaches the end of the buffer, it is immediately evicted.
Otherwise it will follow regular dbuf cache eviction. Since the dbuf
layer does not know actual file sizes, this logic is not applied to
the final buffer of a dnode.
Since uncacheable buffers should no longer stay in the ARC for long,
this patch also tries to optimize I/O by allocating ARC physical
buffers as linear to allow buffer sharing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14243
vdev_geom_read_pool_label() can leave NULL in configs. Check for it
and skip consistently when generating rootconf.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#14291
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Doug Rabson <dfr@rabson.org>
Closes#14286Closes#14287
zfs_zaccess_trivial() calls the generic_permission() to read
xattr attributes. This causes deadlock if called from
zpl_xattr_set_dir() context as xattr and the dent locks are
already held in this scenario. This commit skips the permissions
checks for extended attributes since the Linux VFS stack already
checks it before passing us the control.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14220
When inside a jail, visibility on datasets not "jailed" to the
jail is restricted. However, it was possible to enumerate all
datasets in the pool by looking at the kstats sysctl MIB.
Only the kstats corresponding to datasets that the user has
visibility on are accessible now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14254
zio is never NULL when given to the vdev. Coverity complained saying:
"Either the check against null is unnecessary, or there may be a null
pointer dereference."
Reported-by: Coverity (CID-1466174)
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14263
I read the following article and noticed a couple of ZFS bugs mentioned:
https://pvs-studio.com/en/blog/posts/cpp/0377/
I decided to search for them in the modern OpenZFS codebase and then
found one that matched the description of the first one:
V593 Consider reviewing the expression of the 'A = B != C' kind. The
expression is calculated as following: 'A = (B != C)'. zfs_vfsops.c 498
The consequence of this is that the error value is replaced with `1`
when there is an error. When there is no error, 0 is correctly passed.
This is a very minor issue that is unlikely to cause any real problems.
The incorrect error code would either be returned to the mount command
on a failure or any of `zfs receive`, `zfs recv`, `zfs rollback` or `zfs
upgrade`.
The second one has already been fixed.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14261
- Clang 15 doesn't support `-fno-ipa-sra` anymore. Do a separate
check for `-fno-ipa-sra` support by $KERNEL_CC.
- Don't enable `-mgeneral-regs-only` for certain module files.
Fix#13260
- Scope `GCC diagnostic ignored` statements to GCC only. Clang
doesn't need them to compile the code.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13260Closes#14150
Squelch false positives reported by GCC 12 with UBSan.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#14150
There was the series from me a year ago which fixed most of the
callback vs implementation prototype mismatches. It was based on
running the CFI-enabled kernel (in permissive mode -- warning
instead of panic) and performing a full ZTS cycle, and then fixing
all of the problems caught by CFI.
Now, Clang 16-dev has new warning flag, -Wcast-function-type-strict,
which detect such mismatches at compile-time. It allows to find the
remaining issues missed by the first series.
There are only two of them left: one for the
secpolicy_vnode_setattr() callback and one for taskq_dispatch().
The fix is easy, since they are not used anywhere else.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#14207
Both vop_fsync and vfs_stdsync are effectively just costly no-ops
as they only act on ->v_bufobj.bo_dirty et al, which are unused
by zfs.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#14157
When mounting the root filesystem, vfs_t->mnt_vnodecovered is null
This will cause zfsctl_is_node() to dereference a null pointer when
mounting, or updating the mount flags, on the root filesystem, both
of which happen during the boot process.
Reported-by: Martin Matuska <mm@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#14218
It is protected by z_hold_locks, so we do not need more serialization,
simple integer math should be fine.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#14196
f224eddf92 began dereferencing a NULL
checked pointer in zpl_vap_init(), which made Coverity complain because
either the dereference is unsafe or the NULL check is unnecessary. Upon
inspection, this pointer is guaranteed to never be NULL because it is
from the Linux kernel VFS. The calls into ZFS simply would not make
sense if this pointer were NULL, so the NULL check is unnecessary.
Reported-by: Coverity (CID 1527260)
Reported-by: Coverity (CID 1527262)
Reviewed-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Reviewed-by: Youzhong Yang <yyang@mathworks.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14170
Linux defaults to setting "failfast" on BIOs, so that the OS will not
retry IOs that fail, and instead report the error to ZFS.
In some cases, such as errors reported by the HBA driver, not
the device itself, we would wish to retry rather than generating
vdev errors in ZFS. This new property allows that.
This introduces a per vdev option to disable the failfast option.
This also introduces a global module parameter to define the failfast
mask value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mariusz Zaborski <mariusz.zaborski@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Submitted-by: Klara, Inc.
Closes#14056
If there were no zil entries to replay, skip zil_close. zil_close waits
for a transaction to sync. That can take several seconds, for example
during pool import of a resilvering pool. Skipping zil_close can cut
the time for "zpool import" from 2 hours to 45 seconds on a resilvering
pool with a thousand zvols.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Sponsored-by: Axcient
Closes#13999Closes#14015
Linux 5.17 commit torvalds/linux@5dfbfe71e enables "the idmapping
infrastructure to support idmapped mounts of filesystems mounted
with an idmapping". Update the OpenZFS accordingly to improve the
idmapped mount support.
This pull request contains the following changes:
- xattr setter functions are fixed to take mnt_ns argument. Without
this, cp -p would fail for an idmapped mount in a user namespace.
- idmap_util is enhanced/fixed for its use in a user ns context.
- One test case added to test idmapped mount in a user ns.
Reviewed-by: Christian Brauner <christian@brauner.io>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#14097
Require that ZFS_LEGACY_SUPPORT be defined for legacy ioctl support to
be built. For now, define it in zfs_ioctl_compat.h so support is always
built. This will allow systems that need never support pre-openzfs
tools a mechanism to remove support at build time. This code should
be removed once the need for tool compatability is gone.
No functional change at this time.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
vn_renamepath() is a Solaris-ism that was defined away in the FreeBSD
port. Now that the only use is in the FreeBSD zfs_vnops_os.c, drop it
entierly.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14127
There is an off by 1 error in the check. Fortunately, this function does
not appear to be used in kernel space, despite being compiled as part of
the kernel module. However, it is used in userspace. Callers of
lzc_ioctl_fd() likely will crash if they attempt to use the
unimplemented request number.
This was reported by FreeBSD's coverity scan.
Reported-by: Coverity (CID 1432059)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14135
Some of our customers have been occasionally hitting zfs import failures
in Linux because udevd doesn't create the by-id symbolic links in time
for zpool import to use them. The main issue is that the
systemd-udev-settle.service that zfs-import-cache.service and other
services depend on is racy. There is also an openzfs issue filed (see
https://github.com/openzfs/zfs/issues/10891) outlining the problem and
potential solutions.
With the proper solutions being significant in terms of complexity and
the priority of the issue being low for the time being, this patch
exposes `zfs_vdev_open_timeout_ms` as a tunable so people that are
experiencing this issue often can increase it as a workaround.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#14133
Rather than doing a terrible credential swapping hack, we just
check that the thing being mounted is a snapshot, and the mountpoint
is the zfsctl directory, then we allow it.
If the mount attempt is from inside a jail, on an unjailed dataset
(mounted from the host, not by the jail), the ability to mount the
snapshot is controlled by a new per-jail parameter: zfs.mount_snapshot
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-by: Modirum MDPay
Sponsored-by: Klara Inc.
Closes#13758
Coverity reported that the ASSERT in taskq_create() is always true and
the `*offp > MAXOFFSET_T` check in zfs_file_seek() is always false.
We delete them as cleanup.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14130
Avoid assuming that a pointer can fit in a uint64_t and use uintptr_t
instead.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14131
`snprintf()` is meant to protect against buffer overflows, but operating
on the buffer using its return value, possibly by calling it again, can
cause a buffer overflow, because it will return how many characters it
would have written if it had enough space even when it did not. In a
number of places, we repeatedly call snprintf() by successively
incrementing a buffer offset and decrementing a buffer length, by its
return value. This is a potentially unsafe usage of `snprintf()`
whenever the buffer length is reached. CodeQL complained about this.
To fix this, we introduce `kmem_scnprintf()`, which will return 0 when
the buffer is zero or the number of written characters, minus 1 to
exclude the NULL character, when the buffer was too small. In all other
cases, it behaves like snprintf(). The name is inspired by the Linux and
XNU kernels' `scnprintf()`. The implementation was written before I
thought to look at `scnprintf()` and had a good name for it, but it
turned out to have identical semantics to the Linux kernel version.
That lead to the name, `kmem_scnprintf()`.
CodeQL only catches this issue in loops, so repeated use of snprintf()
outside of a loop was not caught. As a result, a thorough audit of the
codebase was done to examine all instances of `snprintf()` usage for
potential problems and a few were caught. Fixes for them are included in
this patch.
Unfortunately, ZED is one of the places where `snprintf()` is
potentially used incorrectly. Since using `kmem_scnprintf()` in it would
require changing how it is linked, we modify its usage to make it safe,
no matter what buffer length is used. In addition, there was a bug in
the use of the return value where the NULL format character was not
being written by pwrite(). That has been fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
Implement support for Linux's RENAME_* flags (for renameat2). Aside from
being quite useful for userspace (providing race-free ways to exchange
paths and implement mv --no-clobber), they are used by overlayfs and are
thus required in order to use overlayfs-on-ZFS.
In order for us to represent the new renameat2(2) flags in the ZIL, we
create two new transaction types for the two flags which need
transactional-level support (RENAME_EXCHANGE and RENAME_WHITEOUT).
RENAME_NOREPLACE does not need any ZIL support because we know that if
the operation succeeded before creating the ZIL entry, there was no file
to be clobbered and thus it can be treated as a regular TX_RENAME.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
This is in preparation for RENAME_EXCHANGE and RENAME_WHITEOUT support
for ZoL, but the changes here allow for far nicer fallbacks than the
previous implementation (the source and target are re-linked in case of
the final link failing).
In addition, a small cleanup was done for the "target exists but is a
different type" codepath so that it's more understandable.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aleksa Sarai <cyphar@cyphar.com>
Closes#12209Closes#14070
Open files, which aren't present in the snapshot, which is being
roll-backed to, need to disappear from the visible VFS image of
the dataset.
Kernel provides d_drop function to drop invalid entry from
the dcache, but inode can be referenced by dentry multiple dentries.
The introduced zpl_d_drop_aliases function walks and invalidates
all aliases of an inode.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#9600Closes#14070
We ran out of space in enum zio_flag for additional flags. Rather than
introduce enum zio_flag2 and then modify a bunch of functions to take a
second flags variable, we expand the type to 64 bits via `typedef
uint64_t zio_flag_t`.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Richard Yao <richard.yao@klarasystems.com>
Closes#14086
Windows port frees memory that was alloc'd aligned in a different way
then alloc'd memory. So changing frees to be specific.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Innes <andrew.c12@gmail.com>
Co-Authored-By: Jorgen Lundman <lundman@lundman.net>
Closes#14059
The motivation for upgrading our PRNG is the recent buildbot failures in
the ZTS' tests/functional/fault/decompress_fault test. The probability
of a failure in that test is 0.8^256, which is ~1.6e-25 out of 1, yet we
have observed multiple test failures in it. This suggests a problem with
our random number generation.
The xorshift128+ generator that we were using has been replaced by newer
generators that have "better statistical properties". After doing some
reading, it turns out that these generators have "low linear complexity
of the lowest bits", which could explain the ZTS test failures.
We do two things to try to fix this:
1. We upgrade from xorshift128+ to xoshiro256++ 1.0.
2. We tweak random_get_pseudo_bytes() to copy the higher order
bytes first.
It is hoped that this will fix the test failures in
tests/functional/fault/decompress_fault, although I have not done
simulations. I am skeptical that any simulations I do on a PRNG with a
period of 2^256 - 1 would be meaningful.
Since we have raised the minimum kernel version to 3.10 since this was
first implemented, we have the option of using the Linux kernel's
get_random_int(). However, I am not currently prepared to do performance
tests to ensure that this would not be a regression (for the time
being), so we opt for upgrading our PRNG to a newer one from Sebastiano
Vigna.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13983
Adds support for idmapped mounts. Supported as of Linux 5.12 this
functionality allows user and group IDs to be remapped without changing
their state on disk. This can be useful for portable home directories
and a variety of container related use cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12923Closes#13671
Clang's static analyzer complained that we could use after free here if
the inner loop ever iterated. That is a false positive, but upon
inspection, the userland abd_alloc_chunks() function never will put
multiple consecutive pages into a `struct scatterlist`, so there is no
need to loop. We delete the inner loop.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
After Linux 6.1-rc1 came out, the build started failing to build a
couple of the files in the linux spl code due to the mutex_init
redefinition. Moving the sys/mutex.h include to a lower position within
these two files appears to fix the problem.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#14040
This patch inserts the `static` keyword to non-global variables,
which where found by the analysis tool smatch.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13970
These were categorized as the following:
* Dead assignment 23
* Dead increment 4
* Dead initialization 6
* Dead nested assignment 18
Most of these are harmless, but since actual issues can hide among them,
we correct them.
That said, there were a few return values that were being ignored that
appeared to merit some correction:
* `destroy_callback()` in `cmd/zfs/zfs_main.c` ignored the error from
`destroy_batched()`. We handle it by returning -1 if there is an
error.
* `zfs_do_upgrade()` in `cmd/zfs/zfs_main.c` ignored the error from
`zfs_for_each()`. We handle it by doing a binary OR of the error
value from the subsequent `zfs_for_each()` call to the existing
value. This is how errors are mostly handled inside `zfs_for_each()`.
The error value here is passed to exit from the zfs command, so doing
a binary or on it is better than what we did previously.
* `get_zap_prop()` in `module/zfs/zcp_get.c` ignored the error from
`dsl_prop_get_ds()` when the property is not of type string. We
return an error when it does. There is a small concern that the
`zfs_get_temporary_prop()` call would handle things, but in the case
that it does not, we would be pushing an uninitialized numval onto
the lua stack. It is expected that `dsl_prop_get_ds()` will succeed
anytime that `zfs_get_temporary_prop()` does, so that not giving it a
chance to fix things is not a problem.
* `draid_merge_impl()` in `tests/zfs-tests/cmd/draid.c` used
`nvlist_add_nvlist()` twice in ways in which errors are expected to
be impossible, so we switch to `fnvlist_add_nvlist()`.
A few notable ones did not merit use of the return value, so we
suppressed it with `(void)`:
* `write_free_diffs()` in `lib/libzfs/libzfs_diff.c` ignored the error
value from `describe_free()`. A look through the commit history
revealed that this was intentional.
* `arc_evict_hdr()` in `module/zfs/arc.c` did not need to use the
returned handle from `arc_hdr_realloc()` because it is already
referenced in lists.
* `spa_vdev_detach()` in `module/zfs/spa.c` has a comment explicitly
saying not to use the error from `vdev_label_init()` because whatever
causes the error could be the reason why a detach is being done.
Unfortunately, I am not presently able to analyze the kernel modules
with Clang's static analyzer, so I could have missed some cases of this.
In cases where reports were present in code that is duplicated between
Linux and FreeBSD, I made a conscious effort to fix the FreeBSD version
too.
After this commit is merged, regressions like dee8934 should become
extremely obvious with Clang's static analyzer since a regression would
appear in the results as the only instance of unused code. That assumes
that Coverity does not catch the issue first.
My local branch with fixes from all of my outstanding non-draft pull
requests shows 118 reports from Clang's static anlayzer after this
patch. That is down by 51 from 169.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13986
Before this patch, in zfs_domount, if zfs_root or d_make_root fails, we
leave zfsvfs != NULL. This will lead to execution of the error handling
`if` statement at the `out` label, and hence to a call to
dmu_objset_disown and zfsvfs_free.
However, zfs_umount, which we call upon failure of zfs_root and
d_make_root already does dmu_objset_disown and zfsvfs_free.
I suppose this patch rather adds to the brittleness of this part of the
code base, but I don't want to invest more time in this right now.
To add a regression test, we'd need some kind of fault injection
facility for zfs_root or d_make_root, which doesn't exist right now.
And even then, I think that regression test would be too closely tied
to the implementation.
To repro the double-disown / double-free, do the following:
1. patch zfs_root to always return an error
2. mount a ZFS filesystem
Here's the stack trace you would see then:
VERIFY3(ds->ds_owner == tag) failed (0000000000000000 == ffff9142361e8000)
PANIC at dsl_dataset.c:1003:dsl_dataset_disown()
Showing stack for process 28332
CPU: 2 PID: 28332 Comm: zpool Tainted: G O 5.10.103-1.nutanix.el7.x86_64 #1
Call Trace:
dump_stack+0x74/0x92
spl_dumpstack+0x29/0x2b [spl]
spl_panic+0xd4/0xfc [spl]
dsl_dataset_disown+0xe9/0x150 [zfs]
dmu_objset_disown+0xd6/0x150 [zfs]
zfs_domount+0x17b/0x4b0 [zfs]
zpl_mount+0x174/0x220 [zfs]
legacy_get_tree+0x2b/0x50
vfs_get_tree+0x2a/0xc0
path_mount+0x2fa/0xa70
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x38/0x50
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Christian Schwarz <christian.schwarz@nutanix.com>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#14025
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
Coverity complains about possible bugs involving referencing NULL return
values and division by zero. The division by zero bugs require that a
block pointer be corrupt, either from in-memory corruption, or on-disk
corruption. The NULL return value complaints are only bugs if
assumptions that we make about the state of data structures are wrong.
Some seem impossible to be wrong and thus are false positives, while
others are hard to analyze.
Rather than dismiss these as false positives by assuming we know better,
we add defensive assertions to let us know when our assumptions are
wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13972
- Add a zfs_exit() call in an error path, otherwise a lock is leaked.
- Remove the fid_gen > 1 check. That appears to be Linux-specific:
zfsctl_snapdir_fid() sets fid_gen to 0 or 1 depending on whether the
snapshot directory is mounted. On FreeBSD it fails, making snapshot
dirs inaccessible via NFS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Fixes: 43dbf88178 ("FreeBSD: vfsops: use setgen for error case")
Closes#14001Closes#13974
First the function `memset(&key, 0, ...)` but
any call to "goto error;" would call zio_crypt_key_destroy(key) which
calls `rw_destroy()`. The `rw_init()` is moved up to be right after the
memset. This way the rwlock can be released.
The ctx does allocate memory, but that is handled by the memset to 0
and icp skips NULL ptrs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13976
Some header files define structures like this one:
typedef const struct zio_checksum_info {
/* ... */
const char *ci_name;
} zio_abd_checksum_func_t;
So we can use `zio_abd_checksum_func_t` for const declarations now.
It's not needed that we use the `const` qualifier again like this:
`const zio_abd_checksum_func_t *varname;`
This patch solves the double const qualifiers, which were found by
smatch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13961
Both Clang's Static Analyzer and Synopsys' Coverity would ignore
assertions. Following Clang's advice, we annotate our assertions:
https://clang-analyzer.llvm.org/annotations.html#custom_assertions
This makes both Clang's Static Analyzer and Coverity properly identify
assertions. This change reduced Clang's reported defects from 246 to
180. It also reduced the false positives reported by Coverityi by 10,
while enabling Coverity to find 9 more defects that previously were
false negatives.
A couple examples of this would be CID-1524417 and CID-1524423. After
submitting a build to coverity with the modified assertions, CID-1524417
disappeared while the report for CID-1524423 no longer claimed that the
assertion tripped.
Coincidentally, it turns out that it is possible to more accurately
annotate our headers than the Coverity modelling file permits in the
case of format strings. Since we can do that and this patch annotates
headers whenever `__coverity_panic__()` would have been used in the
model file, we drop all models that use `__coverity_panic__()` from the
model file.
Upon seeing the success in eliminating false positives involving
assertions, it occurred to me that we could also modify our headers to
eliminate coverity's false positives involving byte swaps. We now have
coverity specific byteswap macros, that do nothing, to disable
Coverity's false positives when we do byte swaps. This allowed us to
also drop the byteswap definitions from the model file.
Lastly, a model file update has been done beyond the mentioned
deletions:
* The definitions of `umem_alloc_aligned()`, `umem_alloc()` andi
`umem_zalloc()` were originally implemented in a way that was
intended to inform coverity that when KM_SLEEP has been passed these
functions, they do not return NULL. A small error in how this was
done was found, so we correct it.
* Definitions for umem_cache_alloc() and umem_cache_free() have been
added.
In practice, no false positives were avoided by making these changes,
but in the interest of correctness from future coverity builds, we make
them anyway.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13902
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
Coverity found a bug in `zfs_secpolicy_create_clone()` where it is
possible for us to pass an unterminated string when `zfs_get_parent()`
returns an error. Upon inspection, it is clear that using `strlcpy()`
would have avoided this issue.
Looking at the codebase, there are a number of other uses of `strncpy()`
that are unsafe and even when it is used safely, switching to
`strlcpy()` would make the code more readable. Therefore, we switch all
instances where we use `strncpy()` to use `strlcpy()`.
Unfortunately, we do not portably have access to `strlcpy()` in
tests/zfs-tests/cmd/zfs_diff-socket.c because it does not link to
libspl. Modifying the appropriate Makefile.am to try to link to it
resulted in an error from the naming choice used in the file. Trying to
disable the check on the file did not work on FreeBSD because Clang
ignores `#undef` when a definition is provided by `-Dstrncpy(...)=...`.
We workaround that by explictly including the C file from libspl into
the test. This makes things build correctly everywhere.
We add a deprecation warning to `config/Rules.am` and suppress it on the
remaining `strncpy()` usage. `strlcpy()` is not portably avaliable in
tests/zfs-tests/cmd/zfs_diff-socket.c, so we use `snprintf()` there as a
substitute.
This patch does not tackle the related problem of `strcpy()`, which is
even less safe. Thankfully, a quick inspection found that it is used far
more correctly than strncpy() was used. A quick inspection did not find
any problems with `strcpy()` usage outside of zhack, but it should be
said that I only checked around 90% of them.
Lastly, some of the fields in kstat_t varied in size by 1 depending on
whether they were in userspace or in the kernel. The origin of this
discrepancy appears to be 04a479f706 where
it was made for no apparent reason. It conflicts with the comment on
KSTAT_STRLEN, so we shrink the kernel field sizes to match the userspace
field sizes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13876
Coverity found a number of places where we either do MAX(unsigned, 0) or
do assertions that a unsigned variable is >= 0. These do nothing, so
let us drop them all.
It also found a spot where we do `if (unsigned >= 0 && ...)`. Let us
also drop the unsigned >= 0 check.
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13871
Coverity complained about this. An error from `hkdf_sha512()` before uio
initialization will cause pointers to uninitialized memory to be passed
to `zio_crypt_destroy_uio()`. This is a regression that was introduced
by cf63739191. Interestingly, this never
affected FreeBSD, since the FreeBSD version never had that patch ported.
Since moving uio initialization to the top of this function would slow
down the qat_crypt() path, we only move the `memset()` calls to the top
of the function. This is sufficient to fix this problem.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13944
get_user_ns() is only done once for each namespace, so put_user_ns()
should be done once too.
Fix two typos in user_namespace/user_namespace_002.ksh and
user_namespace/user_namespace_003.ksh.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#13918
The FreeBSD project's coverity scans found dead code in `zfs_readdir()`.
Also, the comment above `zfs_readdir()` is out of date.
I fixed the comment and deleted all of the dead code, plus additional
dead code that was found upon review.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13924
The FreeBSD project's coverity scans found this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13923
Coverity reported that we pass a pointer to zfsvfs to
`dmu_objset_disown()` after freeing zfsvfs in zfsvfs_create_impl() after
a failure in zfsvfs_init().
We have nearly identical duplicate versions of this code for FreeBSD and
Linux, but interestingly, the FreeBSD version of this code differs in
such a way that it does not suffer from this bug. We remove the
difference from the FreeBSD version to fix this bug.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13883
param_set_arc_free_target(SYSCTL_HANDLER_ARGS) and
param_set_arc_no_grow_shift(SYSCTL_HANDLER_ARGS) defined in
sysctl_os.c must be made available to arc_os.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#13915
There is an ongoing effort to eliminate this feature.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#13908
The zpl_fadvise() function was recently added and was not included
in the initial patch. Update it accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13831
Replace ZFS_ENTER and ZFS_VERIFY_ZP, which have hidden returns, with
functions that return error code. The reason we want to do this is
because hidden returns are not obvious and had caused some missing fail
path unwinding.
This patch changes the common, linux, and freebsd parts. Also fixes
fail path unwinding in zfs_fsync, zpl_fsync, zpl_xattr_{list,get,set}, and
zfs_lookup().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#13831
When reviewing #13875, I noticed that our FreeBSD code has an issue
where it converts from `int64_t` to `int` when calling
`vnlru_free{,_vfsops}()`. The result is that if the int64_t is `1 <<
36`, the int will be 0, since the low bits are 0. Even when some low
bits are set, a value such as `((1 << 36) + 1)` would truncate to 1,
which is wrong.
There is protection against this on 32-bit platforms, but on 64-bit
platforms, there is no check to protect us, so we add a check.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13882
Unused code detected by coverity.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13868
The function make_dev_s() was introduced to replace make_dev() in
FreeBSD 11.0. It allows further specification of properties and flags
and returns an error code on failure. Using this we can fail loading
the module more gracefully than a panic in situations such as when a
device named zfs already exists. We already use it for zvols.
Use make_dev_s() for /dev/zfs.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13854
When iterating through children physical ashifts for vdev, prefer
ones above the maximum logical ashift, that we can actually use,
but within the administrator defined maximum.
When selecting top-level vdev ashift, do not set it to the defined
maximum in case physical ashift is even higher, but just ignore one.
Using the maximum does not prevent misaligned writes, but reduces
space efficiency. Since ZFS tries to write data sequentially and
aggregates the writes, in many cases large misanigned writes may be
not as bad as the space penalty otherwise.
Allow internal physical ashifts for vdevs higher than SHIFT_MAX.
May be one day allocator or aggregation could benefit from that.
Reduce zfs_vdev_max_auto_ashift default from 16 (64KB) to 14 (16KB),
so that ZFS may still use bigger ashifts up to SHIFT_MAX (64KB),
but only if it really has to or explicitly told to, but not as an
"optimization".
There are some read-intensive NVMe SSDs that report Preferred Write
Alignment of 64KB, and attempt to build RAIDZ2 of those leads to a
space inefficiency that can't be justified. Instead these changes
make ZFS fall back to logical ashift of 12 (4KB) by default and
only warn user that it may be suboptimal for performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#13798
The purpose of this PR is to accepts fadvise ioctl from userland
to do read-ahead by demand.
It could dramatically improve sequential read performance especially
when primarycache is set to metadata or zfs_prefetch_disable is 1.
If the file is mmaped, generic_fadvise is also called for page cache
read-ahead besides dmu_prefetch.
Only POSIX_FADV_WILLNEED and POSIX_FADV_SEQUENTIAL are supported in
this PR currently.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13694
Upon inspection of our code, I noticed that we assume that
__alloc_percpu() cannot fail, and while it probably never has failed in
practice, technically, it can fail, so we should handle that.
Additionally, we incorrectly assume that `taskq_create()` in
spl_kmem_cache_init() cannot fail. The same remark applies to it.
Lastly, `spl-init()` failures should always return negative error
values, but in some places, we are returning positive 1, which is
incorrect. We change those values to their correct error codes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13847
The only event hooked up is NOTE_ATTRIB, which is triggered when the
device is resized.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Wing <rew@FreeBSD.org>
Closes#13773
This will be used to implement kqfilter support for zvol cdevs.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rob Wing <rew@FreeBSD.org>
Closes#13773
FreeBSD had a few platform-specific ARC tunables in the wrong place:
- Move FreeBSD-specifc ARC tunables into the same vfs.zfs.arc node as
the rest of the ARC tunables.
- Move the handlers from arc_os.c to sysctl_os.c and add compat sysctls
for the legacy names.
While here, some additional clean up:
- Most handlers are specific to a particular variable and don't need a
pointer passed through the args.
- Group blocks of related variables, handlers, and sysctl declarations
into logical sections.
- Match variable types for temporaries in handlers with the type of the
global variable.
- Remove leftover comments.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13756
It makes sense to free memory in smaller chunks when approaching
arc_c_min to let other kernel subsystems to free more, since after
that point we can't free anything. This also matches behavior on
Linux, where to shrinker reported only the size above arc_c_min.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13794
The vfs_*_feature() macros turn anything that uses them into dead code,
so we can delete all of it.
As a side effect, zfs_set_fuid_feature() is now identical in
module/os/freebsd/zfs/zfs_vnops_os.c and
module/os/linux/zfs/zfs_vnops_os.c. A few other functions are identical
too. Future cleanup could move these into a common file.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13832
As of the Linux 5.20 kernel blk_cleanup_disk() has been removed,
all callers should use put_disk().
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13728
As of the Linux 5.20 kernel bdevname() has been removed, all
callers should use snprintf() and the "%pg" format specifier.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13728
The file module/os/freebsd/zfs/zfs_ioctl_compat.c fails compiling
because of this error: 'static' is not at beginning of declaration
This commit fixes the three places within that file.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13702
ZIL kstats are reported in an inclusive way, i.e., same counters are
shared to capture all the activities happening in zil. Added support
to report zil stats for every datset individually by combining them
with already exposed dataset kstats.
Wmsum uses per cpu counters and provide less overhead as compared
to atomic operations. Updated zil kstats to replace wmsum counters
to avoid atomic operations.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13636
Makes the case sensitivity setting visible on Linux in /proc/mounts.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13607
Specify the lua and zstd license text in the manor in which the
kernel MODULE_LICENSE macro requires it. The now duplicate entries
were merged and a comment added to make it clear what they apply to.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13641
Follow up fix for a926aab902.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13348Closes#13610
Zp->z_mode is set at the same time inode->i_mode
is being changed. This has the effect of keeping both
in sync without relying on zfs_znode_update_vfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: yanping.gao <yanping.gao@xtaotech.com>
Closes#13581
Handle crypto_dispatch() return values same as crp->crp_etype errors.
On FreeBSD 12 many drivers returned same errors both ways, and lack
of proper handling for the first ended up in assertion panic later.
It was changed in FreeBSD 13, but there is no reason to not be safe.
While there, skip waiting for completion, including locking and
wakeup() call, for sessions on synchronous crypto drivers, such as
typical aesni and software.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13563
Increase nlinks in stat results of ./zfs/snapshot based on snapshot
count. This provides quick and efficient method for administrators to
get snapshot counts without having to use libzfs or list the snapdir
contents.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13559
```
os/linux/zfs/zvol_os.c:1111:3: error: ignoring return value of function
declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
add_disk(zv->zv_zso->zvo_disk);
^~~~~~~~ ~~~~~~~~~~~~~~~~~~~~
zpl_xattr.c:1579:1: warning: no previous prototype for function
'zpl_posix_acl_release_impl' [-Wmissing-prototypes]
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13551
This fd has nothing to do with cleanup, that's just the name of the
field in zfs_cmd_t that was used to pass it to the kernel.
Call it what it is, an fd for a user namespace.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13554
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
Add support for the kernel's block multiqueue (blk-mq) interface in
the zvol block driver. blk-mq creates multiple request queues on
different CPUs rather than having a single request queue. This can
improve zvol performance with multithreaded reads/writes.
This implementation uses the blk-mq interfaces on 4.13 or newer
kernels. Building against older kernels will fall back to the
older BIO interfaces.
Note that you must set the `zvol_use_blk_mq` module param to
enable the blk-mq API. It is disabled by default.
In addition, this commit lets the zvol blk-mq layer process whole
`struct request` IOs at a time, rather than breaking them down
into their individual BIOs. This reduces dbuf lock contention
and overhead versus the legacy zvol submit_bio() codepath.
sequential dd to one zvol, 8k volblocksize, no O_DIRECT:
legacy submit_bio() 292MB/s write 453MB/s read
this commit 453MB/s write 885MB/s read
It also introduces a new `zvol_blk_mq_chunks_per_thread` module
parameter. This parameter represents how many volblocksize'd chunks
to process per each zvol thread. It can be used to tune your zvols
for better read vs write performance (higher values favor write,
lower favor read).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13148
Issue #12483
As of the Linux 5.19 kernel the readpage() address space operation
has been replaced by read_folio().
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 splits the secure
erase functionality from the blkdev_issue_discard() function.
The blkdev_issue_secure_erase() must now be issued to issue
a secure erase.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 removed the
blk_queue_secure_erase() helper function. The preferred
interface is to now use the bdev_max_secure_erase_sectors()
function to check for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@70200574cc removed the
blk_queue_discard() helper function. The preferred interface
is to now use the bdev_max_discard_sectors() function to check
for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As for the Linux 5.18 kernel bio_alloc() expects a block_device struct
as an argument. This removes the need for the bio_set_dev() compatibility
code for 5.18 and newer kernels.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Recognise initial whitespace, + in both cases,
and - also in unsigneds
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13434
Refcount creation for abd_zero_scatter->abd_children is redundant in
abd_alloc_zero_scatter, as it has been done in abd_init_struct.
In addition, abd_children is undefined when ZFS_DEBUG is disabled, the
reference of abd_children in abd_alloc_zero_scatter breaks build of
libzpool when ZFS_DEBUG is disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13429
clang-15 emits the following error message for functions without
a prototype:
fs/zfs/os/linux/spl/spl-kmem-cache.c:1423:27: error:
a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aidan Harris <me@aidanharr.is>
Closes#13421
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
- Prefer O_* flags over F* flags that mostly mirror O_* flags anyway,
but O_* flags seem to be preferred.
- Simplify the code as all the F*SYNC flags were defined as FFSYNC flag.
- Don't define FRSYNC flag, so we don't generate unnecessary ZIL commits.
- Remove EXCL define, FreeBSD ignores the excl argument for zfs_create()
anyway.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13400
When using a Linux kernel which predates the iov_iter interface the
O_APPEND flag should be applied in zpl_aio_write() via the call to
generic_write_checks(). The updated pos variable was incorrectly
ignored resulting in the current offset being used.
This issue should only realistically impact the RHEL/CentOS 7.x
kernels which are based on Linux 3.10.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13370Closes#13377
Linux 5.12 PPC 5.12 get_user() and __copy_from_user_inatomic()
inline helpers very indirectly include a reference to the GPL'd
array mmu_feature_keys[] and fails to build. Workaround this by
using copy_from_user() and throwing EFAULT for any calls to
__copy_from_user_inatomic(). This is a workaround until a fix
for Linux commit 7613f5a66becfd0e43a0f34de8518695888f5458
"powerpc/64s/kuap: Use mmu_has_feature()" is fully addressed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#11958Closes#12590Closes#13367
It turns out, no, in fact, ZERO_RANGE and PUNCH_HOLE do
have differing semantics in some ways - in particular,
one requires KEEP_SIZE, and the other does not.
Also added a zero-range test to catch this, corrected a flaw
that made the punch-hole test succeed vacuously, and a typo
in file_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13329Closes#13338
In hypothetical case of non-linear ABD with single segment, multiple
to page size but not aligned to it, vdev_geom_fill_unmap_cb() could
fill one page less into bio_ma array.
I am not sure it is exploitable, but better to be safe than sorry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13345
Originally it was thought it would be useful to split up the kmods
by functionality. This would allow external consumers to only load
what was needed. However, in practice we've never had a case where
this functionality would be needed, and conversely managing multiple
kmods can be awkward. Therefore, this change merges all but the
spl.ko kmod in to a single zfs.ko kmod.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
As of the 5.17 kernel the GENHD_FL_EXT_DEVT flag has been removed
and the GENHD_FL_NO_PART_SCAN flag renamed GENHD_FL_NO_PART. Update
zvol_alloc() to set GENHD_FL_NO_PART for the newer kernels which
is sufficient. The behavior for prior kernels remains unchanged.
1ebe2e5f ("block: remove GENHD_FL_EXT_DEVT")
46e7eac6 ("block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13294Closes#13297
FreeBSD's memory management system uses its own error numbers and gets
confused when these VOPs return EIO.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Peter Holm <pho@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
For legacy reasons, a couple of VOPs have to return error numbers that
don't come from the usual errno namespace. To handle the cases where
ZFS_ENTER or ZFS_VERIFY_ZP fail, we need to be able to override the
default error return value of EIO. Extend the macros to permit this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
->readpages was removed and replaced by ->readahead. Define
zpl_readahead for kernels that don't have ->readpages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Riccardo Schirone <rschirone91@gmail.com>
Closes#13278
NDF_ONLY_PNBUF has been removed from FreeBSD in favor of NDFREE_PNBUF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13277
Bypass check of ZFS aces if the ACL is trivial. When an ACL is
trivial its permissions are represented by the mode without any
loss of information. In this case, it is safe to convert the
access request into equivalent mode and then pass desired mask
and inode to generic_permission(). This has the added benefit
of also checking whether entries in a POSIX ACL on the file grant
the desired access.
This commit also skips the ACL check on looking up the xattr dir
since such restrictions don't exist in Linux kernel and it makes
xattr lookup behavior inconsistent between SA and file-based
xattrs. We also don't want to perform a POSIX ACL check while
looking up the POSIX ACL if for some reason it is located in
the xattr dir rather than an SA.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13237
The argument type of rw_destroy is (krwlock_t *) while currently
krwlock_t is passed in zfs_ctldir.c. This error is hidden because
rw_destroy is defined as ((void) 0) in linux. But anyway, this
mismatch should be fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13272
When HAVE_BLKDEV_GET_ERESTARTSYS is defined, compiler will complain
"defined but not used" warning for zvol_open_timeout_ms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13270
blkdev.h includes genhd.h since dawn of upstream git, so this is
globally safe
Upstream-commit: 322cbb50de711814c42fb088f6d31901502c711a ("block:
remove genhd.h")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
bio_alloc(gfp_t gfp_mask, unsigned short nr_iovecs)
became
bio_alloc(struct block_device *bdev, unsigned short nr_vecs,
unsigned int opf, gfp_t gfp_mask)
passing NULL/0 continues previous behaviour
Upstream-commit: 07888c665b405b1cd3577ddebfeb74f4717a84c4 ("block:
pass a block_device and opf to bio_alloc")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
Parts of the Linux kernel build system struggle with _Noreturn. This
results in the following warnings when building on RHEL 8.5, and likely
other environments. Switch to using the __attribute__((noreturn)).
warning: objtool: dbuf_free_range()+0x2b8:
return with modified stack frame
warning: objtool: dbuf_free_range()+0x0:
stack state mismatch: cfa1=7+40 cfa2=7+8
...
WARNING: EXPORT symbol "arc_buf_size" [zfs.ko] version generation
failed, symbol will not be versioned.
WARNING: EXPORT symbol "spa_open" [zfs.ko] version generation
failed, symbol will not be versioned.
...
Additionally, __thread_exit() has been renamed spl_thread_exit() and
made a static inline function. This was needed because the kernel
will generate a warning for symbols which are __attribute__((noreturn))
and then exported with EXPORT_SYMBOL.
While we could continue to use _Noreturn in user space I've also
switched it to __attribute__((noreturn)) purely for consistency
throughout the code base.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13238
This PR changes ZFS ACL checks to evaluate
fsuid / fsgid rather than euid / egid to avoid
accidentally granting elevated permissions to
NFS clients.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Andrew Walker <awalker@ixsystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13221
At shutdown time, we drain all of the zevents and set the
ZEVENT_SHUTDOWN flag. On FreeBSD, we may end up calling
zfs_zevent_destroy() after the zevent_lock has been destroyed while
the sysevent thread is winding down; we observe ESHUTDOWN, then back
out.
Events have already been drained, so just inline the kmem_free call in
sysevent_worker() to avoid the race, and document the assumption that
zfs_zevent_destroy doesn't do anything else useful at that point.
This fixes a panic that can occur at module unload time.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#13220
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
On some architectures ZERO_PAGE is unavailable because it references
a GPL exported symbol of empty_zero_page. Originally e08b993 removed
the call to PAGE_ZERO(0) for assignment to the abd_zero_page. However,
a simple check can be done to avoid a kernel allocation and free for
the abd_zero_page if ZERO_PAGE is available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#13199
ZFS allows to update and retrieve additional file level attributes for
FreeBSD. This commit allows additional file level attributes to be
updated and retrieved for Linux. These include the flags stored in the
upper half of z_pflags only.
Two new IOCTLs have been added for this purpose. ZFS_IOC_GETDOSFLAGS
can be used to retrieve the attributes, while ZFS_IOC_SETDOSFLAGS can
be used to update the attributes.
Attributes that are allowed to be updated include ZFS_IMMUTABLE,
ZFS_APPENDONLY, ZFS_NOUNLINK, ZFS_ARCHIVE, ZFS_NODUMP, ZFS_SYSTEM,
ZFS_HIDDEN, ZFS_READONLY, ZFS_REPARSE, ZFS_OFFLINE and ZFS_SPARSE.
Flags can be or'd together while calling ZFS_IOC_SETDOSFLAGS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13118
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
The default behavior where the serious ZFS errors cause FS thread to
stuck is very bad for some production scenario.
In some production scenarios (Linux), it is recommended to make real
kernel PANIC, where system can be rebooted by watchdog or kernel itself.
This patch enables coherent handling of spl_panic_halt parameter.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Wojciech Nizinski <w.nizinski@grinn-global.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12120Closes#13109
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
It's the only one actually used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
To follow a change in illumos taskq
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12802
There's no need to make the platform ops dynamic dispatch.
This change replaces the dynamic dispatch with static calls to the
platform-specific functions.
To avoid name collisions, prefix all platform-specific functions
with `zvol_os_`.
I actually find `zvol_..._os` slightly nicer to read in the calling
code, but having it as a prefix is useful.
Advantage:
- easier jump-to-definition / grepping
- potential benefits to static analysis
- better legibility
Future work: also prefix remaining `static` functions in zvol_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12965
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
First open locking changes were correctly applied to zvol_geom_open but
incorrectly applied to zvol_cdev_open, causing spa_namespace_lock to be
held indefinitely.
Make the first open locking in zvol_cdev_open match zvol_geom_open.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13016
When using the two argument version of submit_bio() in kernel's prior
to 4.8 the first argument should be specified. It's used by block
dump to report the bio direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13006
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
For us, I think it's always just FALLOC_FL_PUNCH_HOLE with a fake
mustache on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
add_disk went from void to must-check int return.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
These are the changes for FreeBSD corresponding to the changes made for
Linux in #12863, see that PR for details.
Changes from #12863 are applied for zvol_geom_open and zvol_cdev_open
on FreeBSD. This also adds a check for the zvol dying which we had
in zvol_geom_open but was missing in zvol_cdev_open. The check causes
the open to fail early with ENXIO when we are in the middle of changing
volmode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
Fix from https://github.com/openzfs/zfs/pull/12844#discussion_r774179413
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12905
sc.nr_to_scan is an input to super_cache_clean (via
shrinker->scan_objects), used to set the number of objects to scan
in the various caches. However super_cache_scan also modifies
sc.nr_to_scan, so when used in a loop we need to reset
sc.nr_to_scan back to our desired nr_to_scan for the next
iteration.
Issue discovered and solution suggested by
Tenzin Lhakhang @tlhakhan.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #12433Closes#12908
When performing I/O on FreeBSD using a file based vdev ensure all
errors encountered when reading/writing are propagated through the
zio pipeline.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12904
Provide access to file generation number on Linux.
Add test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12856
When restructuring the zvol_open() logic for the Linux 5.13 kernel
a lock inversion was accidentally introduced. In the updated code
the spa_namespace_lock is now taken before the zv_suspend_lock
allowing the following scenario to occur:
down_read <=== waiting for zv_suspend_lock
zvol_open <=== holds spa_namespace_lock
__blkdev_get
blkdev_get_by_dev
blkdev_open
...
mutex_lock <== waiting for spa_namespace_lock
spa_open_common
spa_open
dsl_pool_hold
dmu_objset_hold_flags
dmu_objset_hold
dsl_prop_get
dsl_prop_get_integer
zvol_create_minor
dmu_recv_end
zfs_ioc_recv_impl <=== holds zv_suspend_lock via zvol_suspend()
zfs_ioc_recv
...
This commit resolves the issue by moving the acquisition of the
spa_namespace_lock back to after the zv_suspend_lock which restores
the original ordering.
Additionally, as part of this change the error exit paths were
simplified where possible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12863
A recent commit to FreeBSD changed the type of
vop_readdir_args.a_cookies to a uint64_t**. There is no functional
impact to ZFS because ZFS only uses 32-bit cookies, which will be
zero-extended to 64-bits by the existing code.
b214fcceac
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#12874
va_seq was actually a thin veil over va_gen, so z_gen is a more
appropriate value than z_seq to populate the field with.
Drop the unnecessary compat obfuscation and provide the correct
file generation number.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#12851
When rolling back a dataset, ZFS has to purge file data resident in the
system page cache. To do this, it loops over all vnodes for the
mountpoint and calls vn_pages_remove() to purge pages associated with
the vnode's VM object. Each page is thus exclusively busied while the
dataset's teardown write lock is held.
When handling a page fault on a mapped ZFS file, FreeBSD's page fault
handler busies newly allocated pages and then uses VOP_GETPAGES to fill
them. The ZFS getpages VOP acquires the teardown read lock with vnode
pages already busied. This represents a lock order reversal which can
lead to deadlock.
To break the deadlock, observe that zfs_rezget() need only purge those
pages marked valid, and that pages busied by the page fault handler are,
by definition, invalid. Furthermore, ZFS pages always transition from
invalid to valid with the teardown lock held, and ZFS never creates
partially valid pages. Thus, zfs_rezget() can use the new
vn_pages_remove_valid() to skip over pages busied by the fault handler.
PR: 258208
Tested by: pho
Reviewed by: avg, sef, kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D32931
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12828
The definition of struct blkcg_gq was moved into blk-cgroup.h, which is
a header that's been in Linux since 2015. This is used by
vdev_blkg_tryget() in module/os/linux/zfs/vdev_disk.c. Since the kernel
for CentOS 7 and similar-generation releases doesn't have this header,
its inclusion is guarded by a configure test.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
This change adds a confiugre check to determine if bio_set_dev is a
helper macro or not. If not, then the attempt to override its internal
call to bio_associate_blkg(), with a macro definition to our own
version, is no longer possible, as the compiler won't use it when
compiling the new inline function replacement implemented in the header.
This change also creates a new vdev_bio_set_dev() function that performs
the same work, and also performs the work implemented in
vdev_bio_associate_blkg(), as it is the only thing calling that function
in our code. Our custom vdev_bio_associate_blkg() is now only compiled
if the bio_set_dev() is a macro in the Linux headers.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The iov_iter->type member was renamed iov_iter->iter_type. However,
while looking into this, realized that in 2018 a iov_iter_type(*iov)
accessor function was introduced. So if that is present, use it,
otherwise fall back to trying the existing behavior of directly
accessing type from iov_iter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The return type for the submit_bio member of struct
block_device_operations was changed to no longer return a value.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
- To avoid a use-after-free, zfsvfs->z_log needs to be loaded after the
teardown lock is acquired with ZFS_ENTER().
- Avoid leaking vnode locks in zfs_rename_relock() and zfs_rename_()
when the ZFS_ENTER() macros forces an early return.
Refactor the rename implementation so that ZFS_ENTER() can be used
safely. As a bonus, this lets us use the ZFS_VERIFY_ZP() macro instead
of open-coding its implementation.
Reported-by: Peter Holm <pho@FreeBSD.org>
Tested-by: Peter Holm <pho@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12717
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12771
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12748
The submit_bio() prototype has changed again. The version is 5.16
still only expects a single argument but the return type has changed
to void. Since we never used the returned value before update the
configure check to detect both single arg versions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
On Linux, sometimes, when ZFS goes to unmount an automounted snap,
it fails a VERIFY check on debug builds, because taskq_cancel_id
returned ENOENT after not finding the taskq it was trying to cancel.
This presumably happens when it already died for some reason; in this
case, we don't really mind it already being dead, since we're just
going to dispatch a new task to unmount it right after.
So we just ignore it if we get back ENOENT trying to cancel here,
retry a couple times if we get back the only other possible condition
(EBUSY), and log to dbgmsg if we got anything but ENOENT or success.
(We also add some locking around taskqid, to avoid one or two cases
of two instances of trying to cancel something at once.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11632Closes#12670
We move the spinlock unlock before the thread creation. This should be
safe because the thread creation code doesn't actually manipulate any
taskq data structures; that's done by the thread once it's created.
We also remove the assertion that the maxthreads is the current threads
plus one; that assertion could fail if multiple hotplug events come in
quick succession, and the first new taskq thread hasn't had a chance to
start processing yet.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
eviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12714
We have to hold the teardown lock while dereferencing zfsvfs->z_os and,
I believe, when committing to the ZIL.
Note that jumping to the "out" label, "error" is always non-zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
The objset object is reallocated during certain dataset operations, such
as rollbacks, so the objset pointer must be loaded after acquiring the
teardown lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
Make the main dmu_buf_hold_array() function non-static.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12628
While switching abd_zero_buf allocation KPI I've missed the fact
that kmem_zalloc() zeroed the allocation, while kmem_cache_alloc()
does not. Add explicit bzero() after it.
I don't think it should have caused real problems, but leaking one
memory page content all over the pool is not good.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12569
When mounting a snapshot in the .zfs/snapshots control directory,
temporarily assume roots credentials to perform the VFS_MOUNT().
This allows regular users and users inside jails to access these
snapshots.
The regular usermount code is not helpful here, since it requires
that the user performing the mount own the mountpoint, which won't
be the case for .zfs/snapshot/<snapname>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Modirum MDPay
Sponsored-By: Klara Inc.
Closes#11312
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
We attempt to remove an existing SA xattr when setting a dir xattr, but
this only makes sense if the znode has been upgraded to the SA format.
Otherwise, we will hit an assert in zfs_sa_get_xattr.
Make sure this is an SA znode before attempting to remove the SA xattr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12514
This adds supports for hole-punching facilities in the FreeBSD kernel
starting from __FreeBSD_version 1400032.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
Linux 4.11 added a new statx system call that allows us to expose crtime
as btime. We do this by caching crtime in the znode to match how atime,
ctime and mtime are cached in the inode.
statx also introduced a new way of reporting whether the immutable,
append and nodump bits have been set. It adds support for reporting
compression and encryption, but the semantics on other filesystems is
not just to report compression/encryption, but to allow it to be turned
on/off at the file level. We do not support that.
We could implement semantics where we refuse to allow user modification
of the bit, but we would need to do a dnode_hold() in zfs_znode_alloc()
to find out encryption/compression information. That would introduce
locking that will have a minor (although unmeasured) performance cost.
It also would be inferior to zdb, which reports far more detailed
information. We therefore omit reporting of encryption/compression
through statx in favor of recommending that users interested in such
information use zdb.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#8507
When a header is allocated for full overwrite it is a waste of time
to allocate b_pabd/b_rabd for it, since arc_write() will free them
without ever being touched. If it is a read or a partial overwrite
then arc_read() and arc_hdr_decrypt() allocate them explicitly.
Reduced memory allocation in user threads also reduces ARC eviction
throttling there, proportionally increasing it in ZIO threads, that
is not good. To minimize or even avoid it introduce ARC allocation
reserve, allowing certain arc_get_data_abd() callers to allocate a
bit longer in situations where user threads will already throttle.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12398
Before OpenZFS 2.0, trying to set the FreeBSD sysctl vfs.zfs.arc_max
to a disallowed value would return an error.
Since the switch, it instead only generates WARN_IF_TUNING_IGNORED
Keep the ability to set the sysctl's specifically to 0, even though
that is less than the minimum, because some tests depend on this.
Also lost, was the ability to set vfs.zfs.arc_max to a value less
than the default vfs.zfs.arc_min at boot time. Restore this as well.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12161
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Martin Matuska <mm@FreeBSD.org>
Co-authored-by: Konstantin Belousov <kib@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
External-issue: https://reviews.freebsd.org/D31207Closes#12442
The /proc/diskstats accounting needs to be explicitly enabled
for block devices which do not use multi-queue.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12440Closes#12066
CpaDcGeneratefooter function that obtain the checksum code
does not support the CPA_DC_STATELESS mode. So we get the
adler32 chencksum of the end of the zlib from dc_results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: hedong.zhang <h_d_zhang@163.com>
Closes#12343
We have a tunable which permits one to disable the use of unmapped I/O
for the buffer cache. Respect it in ZFS as well. This is useful for
KMSAN, which cannot easily maintain shadow state for unmapped pages.
No functional change intended, as unmapped I/O is permitted by default
and there's no real reason to disable it in practice except for
debugging.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12446
It is wrong for arc_write_ready() to use zfs_abd_scatter_enabled to
decide whether to reallocate/copy the buffer, because the answer is
OS-specific and depends on the buffer size. Instead of that use
abd_size_alloc_linear(), moved into public header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12425
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
Kernel 5.14 introduced a change where set_page_dirty of
struct address_space_operations is no longer implicitly set to
__set_page_dirty_buffers(), which ended up resulting in a NULL
pointer deref in the kernel when it is attempted to be called.
This change sets .set_page_dirty in the structure to
__set_page_dirty_nobuffers(), which was introduced with the
related patch set. The breaking change was introduce in commit
0af573780b0b13fceb7fabd49dc1b073cee9a507 to torvalds/linux.git.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12427
In Linux 5.14, blk_alloc_queue is no longer exported, and its usage
has been superseded by blk_alloc_disk, which returns a gendisk struct
from which we can still retrieve the struct request_queue* that is
needed in the one place where it is used. This also replaces the call
to alloc_disk(minors), and minors is now set via struct member
assignment.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12362Closes#12409
Since errors returned by zvol_create_minor_impl() are ignored by the
common code, it is more convenient to ignore make_dev_s() errors there.
It allows, for example, to get device created for the zvol after later
rename instead of having it further stuck in half-created state.
zvol_rename_minor() already ignores those errors.
While there, switch from MAXPHYS to maxphys in FreeBSD 13+.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12375
* zio: avoid callback typecasting
* zil: avoid zil_itxg_clean() callback typecasting
* zpl: decouple zpl_readpage() into two separate callbacks
* nvpair: explicitly declare callbacks for xdr_array()
* linux/zfs_nvops: don't use external iput() as a callback
* zcp_synctask: don't use fnvlist_free() as a callback
* zvol: don't use ops->zv_free() as a callback for taskq_dispatch()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12260
We should use SET_ERROR when we first get an error.
Add it in the FreeBSD xattr implementations where missing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12356
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12378
arc_evict_hdr() returns number of evicted bytes in scope of specific
state. For ghost states it does not mean the amount of really freed
memory, but the logical buffer size. It is correct for the eviction
process, but not for waking up threads waiting for ARC size reduction,
as added in "Revise ARC shrinker algorithm" commit, causing premature
wakeups while ARC is still overflowed, allowing even bigger overflow,
plus processing overhead when next allocation will also get blocked,
probably also for too short time.
To fix that make arc_evict_hdr() also return the amount of really
freed memory, which for the ghost states is only the header, and use
it to update arc_evict_count instead. Originally I was thinking to
not return it at all, since arc_get_data_impl() does not account for
the headers, but decided that some slow allocation progress is better
than long waits, reaching on my tests up to 100ms.
To reduce negative latency effects of long time periods when reclaim
thread can free little real memory, start reclamation process earlier,
before we actually reached the overflow threshold, when we have to
throttle new allocations. We can also do it without taking global
arc_evict_lock, reducing the contention.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12279
Callers of zfs_file_get and zfs_file_put can corrupt the reference
counts for the file structure resulting in a panic or a soft lockup.
When zfs send/recv runs, it will add a reference count to the
open file, and begin to send or recv the stream. If the file descriptor
is closed, then when dmu_recv_stream() or dmu_send() return we will
call zfs_file_put to remove the reference we placed on the file
structure. Unfortunately, because zfs_file_put() uses the file
descriptor to lookup the file structure, it may end up finding that
the file descriptor table no longer contains the file struct, thus
leaking the file structure. Or it might end up finding a file
descriptor for a different file and blindly updating its reference
counts. Other failure modes probably exists.
This change reworks the zfs_file_[get|put] interface to not rely
on the file descriptor but instead pass the zfs_file_t pointer around.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-issue: DLPX-76119
Closes#12299
Many FreeBSD disk drivers support "unmapped" I/O mode, when data
buffer represented not with a virtually contiguous KVA-mapped address
range, but with a list of physical memory pages. Originally it was
designed to do I/O from buffers without KVA mapping (unmapped). But
moving virtual addresses out of equation allows us to operate even
non-contiguous data buffers with one condition: all buffer discon-
tinuities must be aligned to memory page borders.
Doing I/O to capable GEOM device this patch traverses through non-
linear ABD buffers, validating the chunks borders. If the condition
is met, it supplies GEOM with the list of original physical memory
pages instead of copying the data into temporary contiguous buffer.
On capable hardware on pools with ashift=12 and default ABD chunk of
4KB it should handle all the I/O without additional memory copying.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12320
It makes no sense to set it below PAGE_SIZE, since it increases all
overheads and makes returning memory to OS problematic. It makes no
sense to set it above PAGE_SIZE, since such allocations and especially
frees are too expensive and cause KVA fragmentation to benefit from
fewer chunks. After that it makes no sense to keep more complicated
math here.
What may have sense though is just a tunable border between linear and
scatter ABDs, previously also controlled by this tunable. Retain that
functionality by taking abd_scatter_min_size tunable from Linux, just
with different default value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12328
Fix a leak of abd_t that manifested mostly when using
raidzN with at least as many columns as N (e.g. a
four-disk raidz2 but not a three-disk raidz2).
Sufficiently heavy raidz use would eventually run a system
out of memory.
Additionally:
* Switch abd_cache arena to FIRSTFIT, which empirically
improves perofrmance.
* Make abd_chunk_cache more performant and debuggable.
* Allocate the abd_zero_buf from abd_chunk_cache rather
than the heap.
* Don't try to reap non-existent qcaches in abd_cache arena.
* KM_PUSHPAGE->KM_SLEEP when allocating chunks from their
own arena
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: Sean Doran <smd@use.net>
Closes#12295
Compiling with gcc 11.1.0 produces three new warnings.
Change the code slightly to avoid them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12130Closes#12188Closes#12237
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
In all places except two spa_get_random() is used for small values,
and the consumers do not require well seeded high quality values.
Switch those two exceptions directly to random_get_pseudo_bytes()
and optimize spa_get_random(), renaming it to random_in_range(),
since it is not related to SPA or ZFS in general.
On FreeBSD directly map random_in_range() to new prng32_bounded() KPI
added in FreeBSD 13. On Linux and in user-space just reduce the type
used to uint32_t to avoid more expensive 64bit division.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12183
wmsum was designed exactly for cases like these with many updates
and rare reads. It allows to completely avoid atomic operations on
congested global variables.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12172
In zfs_znode_alloc we always hash inodes. If the
znode is unlinked, we do not need to hash it. This
fixes the problem where zfs_suspend_fs is doing zrele
(iput) in an async fashion, and zfs_resume_fs unlinked
drain processing will try to hash an inode that could
still be hashed, resulting in a panic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alan Somers <asomers@gmail.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9741Closes#11223Closes#11648Closes#12210
This mostly reverts "3537 want pool io kstats" commit of 8 years ago.
From one side this code using pool-wide locks became pretty bad for
performance, creating significant lock contention in I/O pipeline.
From another, there are more efficient ways now to obtain detailed
statistics, while this statistics is illumos-specific and much less
usable on Linux and FreeBSD, reported only via procfs/sysctls.
This commit does not remove KSTAT_TYPE_IO implementation, that may
be removed later together with already unused KSTAT_TYPE_INTR and
KSTAT_TYPE_TIMER.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12212
`getfsstat(2)` is used to retrieve the list of mounted file systems,
which libzfs uses when fetching properties like mountpoint, atime,
setuid, etc. The `mode` parameter may be `MNT_NOWAIT`, which uses
information in the VFS's cache, or `MNT_WAIT`, which effectively does a
`statfs` on every single mounted file system in order to fetch the most
up-to-date information. As far as I can tell, the only fields that
libzfs cares about are the filesystem's name, mountpoint, fstypename,
and mount flags. Those things are always updated on mount and unmount,
so they will always be accurate in the VFS's mount cache except in two
circumstances:
1) When a file system is busy unmounting
2) When a ZFS file system changes the value of a mount-overridable
property like atime or setuid, but doesn't remount the file system.
Right now that only happens when the property is changed by an
unprivileged user who has delegated authority to change the property
but not to mount the dataset. But perhaps libzfs could choose to do
it for other reasons in the future.
Switching to `MNT_NOWAIT` will greatly improve speed with no downside,
as long as we explicitly update the mount cache whenever we change a
mount-overridable property.
For comparison, Illumos gets this information using the native
`getmntany` and `getmntent` functions, which also use cached
information. The illumos function that would refresh the cache,
`resetmnttab`, is never called by libzfs.
And on GNU/Linux, `getmntany` and `getmntent` don't even communicate
with the kernel directly. They simply parse the file they are given,
which is usually /etc/mtab or /proc/mounts. Perhaps the implementation
of /proc/mounts is synchronous, ala MNT_WAIT; I don't know.
Sponsored-by: Axcient
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes: #12091
VFS_QUOTACTL(9) has been updated to allow each filesystem to indicate
whether it has changed the busy state of the mount. The filesystem
may still assume that its .vfs_quotactl entrypoint is always called
with the mount busied, but only needs to unbusy the mount (and clear
*mp_busy) if it does something that actually requires the mount to be
unbusied. It no longer needs to blindly copy-paste the UFS protocol
for calling vfs_unbusy(9) for the Q_QUOTAOFF and Q_QUOTAON commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jason Harmening <jason.harmening@gmail.com>
Closes#12052
For small objects the kernel's slab implementation is very fast and
space efficient. However, as the allocation size increases to
require multiple pages performance suffers. The SPL kmem cache
allocator was designed to better handle these large allocation
sizes. Therefore, on Linux the kmem_cache_* compatibility wrappers
prefer to use the kernel's slab allocator for small objects and
the custom SPL kmem cache allocator for larger objects.
This logic was effectively disabled for all architectures using
a non-4K page size which caused all kmem caches to only use the
SPL implementation. Functionally this is fine, but the SPL code
which calculates the target number of objects per-slab does not
take in to account that __vmalloc() always returns page-aligned
memory. This can result in a massive amount of wasted space when
allocating tiny objects on a platform using large pages (64k).
To resolve this issue we set the spl_kmem_cache_slab_limit cutoff
to 16K for all architectures.
This particular change does not attempt to update the logic used
to calculate the optimal number of pages per slab. This remains
an issue which should be addressed in a future change.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12152Closes#11429Closes#11574Closes#12150
Both were removed in 4fbdb10c7b ("remove
kmem_cache module parameter KMC_EXPIRE_AGE")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
The additional iter advance is incorrect, as copy_from_iter() has
already done the right thing. This will result in the following
warning being printed to the console as of the 5.12 kernel.
Attempted to advance past end of bvec iter
This change should have been included with #11378 when a
similar change was made on the read side.
Suggested-by: @siebenmann
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Issue #11378Closes#12041Closes#12155
Just like #12087, the set_acl signature changed with all the bolted-on
*userns parameters, which disabled set_acl usage, and caused #12076.
Turn zpl_set_acl into zpl_set_acl and zpl_set_acl_impl, and add a
new configure test for the new version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12076Closes#12093
Previous commit added accounting for geom mode, but not for dev.
In geom mode we actually have GEOM statistics, while in dev mode
additional accounting actually makes more sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12097
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12049
I looked for a bit, and couldn't find any documentation on
how to print all logged dbgmsg entries, just messages since
the DTrace probe started, until @allanjude kindly pointed me
toward the sysctl.
So let's add that note where the DTrace probe is mentioned for
FreeBSD, so other people can find it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12113
ZFS does not expect transient errors from crypto. For read they are
counted as checksum errors, while for write end up in panic. To not
panic on random low memory conditions retry ENOMEM errors in the OCF
wrapper function.
While there remove unneeded timeout and priority from msleep().
External-issue: https://reviews.freebsd.org/D30339
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12077
Coleman Kane
Chunwei Chen
Richard Yao
Mateusz Piotrowski
Antonio Russo
Mateusz Guzik
Alexander Motin
Ryan Moeller
Doug Rabson
Ameer Hamza
Allan Jude
szubersk
Alexander
Mariusz Zaborski
Alan Somers
youzhongyang
Brooks Davis
Serapheim Dimitropoulos
Aleksa Sarai
Pavel Snajdr
Andrew Innes
Tino Reichardt
Christian Schwarz
Mark Johnston
Jorgen Lundman
Martin Matuška
Brian Behlendorf
Finix1979
Rob Wing
наб
gaoyanping
Andrew
Ryan Moeller
Will Andrews
Tony Hutter
hping
Aidan Harris
Shaan Nobee
Pawel Jakub Dawidek
Satadru Pramanik
Rich Ercolani
Mark Johnston
Riccardo Schirone
hpingfs
Kyle Evans
Brian Atkinson
Umer Saleem
Jitendra Patidar
drowfx
Christian Schwarz
Rich Ercolani
George Amanakis
chrisrd
Paul Dagnelie
Damian Szuberski
Ka Ho Ng
Richard Yao
hedongzhang
George Wilson
Attila Fülöp
Paul Zuchowski
jharmening