This patch adds a command (-c) option to zpool status and zpool iostat. The
-c option allows you to run an arbitrary command on each vdev and display
the first line of output in zpool status/iostat. The environment vars
VDEV_PATH and VDEV_UPATH are set to the vdev's path and "underlying path"
before running the command. For device mapper, multipath, or partitioned
vdevs, VDEV_UPATH is the actual underlying /dev/sd* disk. This can be useful
if the command you're running requires a /dev/sd* device.
The patch also uses /sys/block/<dev>/slaves/ to lookup the underlying device
instead of using libdevmapper. This not only removes the libdevmapper
requirement at build time, but also allows you to resolve device mapper
devices without being root. This means that UDEV_UPATH get set correctly
when running zpool status/iostat as an unprivileged user.
Example:
$ zpool status -c 'echo I am $VDEV_PATH, $VDEV_UPATH'
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
mpatha ONLINE 0 0 0 I am /dev/mapper/mpatha, /dev/sdc
sdb ONLINE 0 0 0 I am /dev/sdb1, /dev/sdb
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#5368
Repair indent of zpool.8 man page, just before zpool labelclear
details. Accidentally introduced by 193a37cb2 (git bisect).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5394
Sometimes it is desirable to specifically disable one or several
features directly on the 'zpool create' command line.
$ zpool create -o feature@<feature>=disabled ...
Original-patch-by: Turbo Fredriksson <turbo@bayour.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#3460Closes#5142Closes#5324
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
Various rewrites to the descriptions of module parameters. Corrects
spelling mistakes, makes descriptions them more user-friendly and
describes some ZFS quirks which should be understood before changing
parameter values.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4671
This is a purely cosmetical change, to consistently prefer one of
two (both acceptable) choises for the word parsable in documentation and
code. I don't really care which to use, but acording to wiktionary
https://en.wiktionary.org/wiki/parsable#English parsable is preferred.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4682
These changes should have been part of the original 930b0d4
commit but were overlooked because 193a37c had not yet been
merged when the original change was ported.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4631
3993 zpool(1M) and zfs(1M) should support -p for "list" and "get"
4700 "zpool get" doesn't support -H or -o options
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/3993
OpenZFS-issue: https://www.illumos.org/issues/4700
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c58b352
Porting notes:
I removed ZoL's zpool_get_prop_literal() in favor of
zpool_get_prop(..., boolean_t literal) since that's what OpenZFS
uses. The functionality is the same.
This is foundational work for ZED.
Updates a leaf vdev's persistent device strings on Linux platform
* only applies for a dedicated leaf vdev (aka whole disk)
* updated during pool create|add|attach|import
* used for matching device matching during auto-{online,expand,replace}
* stored in a leaf disk config label (i.e. alongside 'path' NVP)
* can opt-out using env var ZFS_VDEV_DEVID_OPT_OUT=YES
Some examples:
path: '/dev/sdb1'
devid: 'scsi-350000394a8ca4fbc-part1'
phys_path: 'pci-0000:04:00.0-sas-0x50000394a8ca4fbf-lun-0'
path: '/dev/mapper/mpatha'
devid: 'dm-uuid-mpath-35000c5006304de3f'
Signed-off-by: Don Brady <don.brady@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2856Closes#3978Closes#4416
Historically libblkid support was detected as part of configure
and optionally enabled. This was done because at the time support
for detecting ZFS pool vdevs had just be added to libblkid and
those updated packages were not yet part of many distributions.
This is no longer the case and any reasonably current distribution
will ship a version of libblkid which can detect ZFS pool vdevs.
This patch makes libblkid mandatory at build time and libblkid
the preferred method of scanning for ZFS pools. For distributions
which include a modern version of libblkid there is no change in
behavior. Explicitly scanning the default search paths is still
supported and can be enabled with the '-s' command line option.
Additionally making libblkid mandatory means that the 'zpool create'
command can reliably detect if a specified device has an existing
non-ZFS filesystem (ext4, xfs) and print a warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2448
Commit d2f3e29 introduced the -p option which outputs full paths
for vdevs to multiple zpool subcommands. When this was merged
there was no conflict for this flag letter. However it's certain
there will be a conflict with the -p (parsable) flag used by other
subcommands. Therefore, -p is being changed to -P to avoid this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4368
The following options have been added to the zpool add, iostat,
list, status, and split subcommands. The default behavior was
not modified, from zfs(8).
-g Display vdev GUIDs instead of the normal short
device names. These GUIDs can be used in-place of
device names for the zpool detach/off‐
line/remove/replace commands.
-L Display real paths for vdevs resolving all symbolic
links. This can be used to lookup the current block
device name regardless of the /dev/disk/ path used
to open it.
-p Display full paths for vdevs instead of only the
last component of the path. This can be used in
conjunction with the -L flag.
This behavior may also be enabled using the following environment
variables.
ZPOOL_VDEV_NAME_GUID
ZPOOL_VDEV_NAME_FOLLOW_LINKS
ZPOOL_VDEV_NAME_PATH
This change is based on worked originally started by Richard Yao
to add a -g option. Then extended by @ilovezfs to add a -L option
for openzfsonosx. Those changes have been merged, re-factored,
a -p option added and extended to all relevant zpool subcommands.
Original-patch-by: Richard Yao <ryao@gentoo.org>
Extended-by: ilovezfs <ilovezfs@icloud.com>
Extended-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: ilovezfs <ilovezfs@icloud.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2011Closes#4341
Correct some misspelled words and grammatical errors, and remove
trailing white space in the man pages.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4115
A few minor mistakes than should be fixed:
zpool:
compatability -> compatibility
zfs:
accessable -> accessible
availible -> available
zfs-events:
availible -> available
zfs-module-parameters:
proceding -> proceeding
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3544
sysstat's iostat omits the first report when the -y option is used.
This patch adds that functionality and omits the first report with
statistics since system boot.
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3439
* Add information about the 'zpool events' command in zpool(8).
* More events and payloads defined in zfs-events(5).
* I/O Stages and I/O Flags sections added.
* Remove unused legacy "zio_deadline" payload define.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3467
Support exporting all imported pools in one go, using 'zpool export -a'.
This is accomplished by moving the export parts from zpool_do_export()
in to the new function zpool_export_one(). The for_each_pool() function
is used to enumerate the list of pools to be exported. Passing an argc
of 0 implies the function should be called on all pools.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #3203
Creating virtual machines that have their rootfs on ZFS on hosts that
have their rootfs on ZFS causes SPA namespace collisions when the
standard name rpool is used. The solution is either to give each guest
pool a name unique to the host, which is not always desireable, or boot
a VM environment containing an ISO image to install it, which is
cumbersome.
26b42f3f9d introduced `zpool import -t
...` to simplify situations where a host must access a guest's pool when
there is a SPA namespace conflict. We build upon that to introduce
`zpool import -t tname ...`. That allows us to create a pool whose
in-core name is tname, but whose on-disk name is the normal name
specified.
This simplifies the creation of machine images that use a rootfs on ZFS.
That benefits not only real world deployments, but also ZFSOnLinux
development by decreasing the time needed to perform rootfs on ZFS
experiments.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
zpool import's -t parameter is intended for use with -R when operating
on pools that belong to other systems. Like -R, pools imported in this
way should not update the cachefile unless explicitly requested. The
initial implementation allowed the cachefile to be updated when -R was
not used. This went uncaught during testing because -R had implicitly
disabled use of the cachefile.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2417
This documentation is based FreeBSD's zpool(8) man page.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2682
4976 zfs should only avoid writing to a failing non-redundant top-level vdev
4978 ztest fails in get_metaslab_refcount()
4979 extend free space histogram to device and pool
4980 metaslabs should have a fragmentation metric
4981 remove fragmented ops vector from block allocator
4982 space_map object should proactively upgrade when feature is enabled
4983 need to collect metaslab information via mdb
4984 device selection should use fragmentation metric
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <adam.leventhal@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
https://www.illumos.org/issues/4976https://www.illumos.org/issues/4978https://www.illumos.org/issues/4979https://www.illumos.org/issues/4980https://www.illumos.org/issues/4981https://www.illumos.org/issues/4982https://www.illumos.org/issues/4983https://www.illumos.org/issues/4984https://github.com/illumos/illumos-gate/commit/2e4c998
Notes:
The "zdb -M" option has been re-tasked to display the new metaslab
fragmentation metric and the new "zdb -I" option is used to control
the maximum number of in-flight I/Os.
The new fragmentation metric is derived from the space map histogram
which has been rolled up to the vdev and pool level and is presented
to the user via "zpool list".
Add a number of module parameters related to the new metaslab weighting
logic.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2595
This functionality is already available in 'zfs get'. Providing
it for 'zpool get' is useful and good for consistency.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #2522
Most ZFS implementations seemed to have missed this bit of documentation.
The additional text is based on FreeBSD's man page.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2416
Users need to be aware that when replacing devices in an existing
pool they may need to override automatically detected ashift value.
This will all depend on the exact hardware they are using.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2024
The property name gets mangled with the explanation due to the property
length. Fixed by putting the explanation on the next line.
Before:
unsupported@feature_Info rmation about unsupported features that are
enabled on the pool. See zpool-features(5) for details.
After:
unsupported@feature_guid
Information about unsupported features that are enabled on the pool. See
zpool-features(5) for details.
Signed-off-by: SenH <sen@senhaerens.be>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2419
These options have existed for a long time but have historically
been undocumented because they are not guaranteed to be safe. They
should only be used as a last resort when attempting to recover a
damaged pool.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1130
Users need to be aware that when adding devices to an existing pool
they may need to override automatically detected ashift value.
This will all depend on the exact hardware they are using.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #2024
Originally, users had to handle spa namespace collisions by either
exporting the already imported pool or by specifying a new name for the
pool with a conflicting name. In the case of root pools from virtual
guests, neither approach to collision resolution is reasonable. This is
addressed by extending the new name syntax with a -t option to specify
that the new name is temporary. When specified, this sets an internal
flag that is passed into the kernel to tell it that all label updates
should refer to the name used in the original label. Consequently, the
original pool name will be retained on export.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2189
This works the same as the -p switch to "zfs get", displaying full
resolution values for appropriate attributes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1813
Document the "-D" and "-T" options and the optional interval
and count or "zpool status".
Also for zpool's man page, use a consistent order for the
various "-T" options to match the program's help output.
Document the effect of additional "-D" options for zdb.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1786
The detach section of the zpool(8) man page now suggests the
offline command. Using offline may be more appropriate for
certain situations.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1776
zpool list has the same options for repeating as zpool iostat
has, but that is not documented. This patch adds the documentation.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The FreeBSD implementation of zfs adds the 'zpool labelclear'
command. Since this functionality is helpful and straight
forward to add it is being included in ZoL.
References:
freebsd/freebsd@119a041dc9
Ported-by: Dmitry Khasanov <pik4ez@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1126
Adds zpool split documentation to the zpool man page. I only documented
the options that I could get to work. While it is documented on some
sun blogs that devices can be specified for split, I was not able to get
that to work during my testing.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1456
3306 zdb should be able to issue reads in parallel
3321 'zpool reopen' command should be documented in the man
page and help
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
illumos/illumos-gate@31d7e8fa33https://www.illumos.org/issues/3306https://www.illumos.org/issues/3321
The vdev_file.c implementation in this patch diverges significantly
from the upstream version. For consistenty with the vdev_disk.c
code the upstream version leverages the Illumos bio interfaces.
This makes sense for Illumos but not for ZoL for two reasons.
1) The vdev_disk.c code in ZoL has been rewritten to use the
Linux block device interfaces which differ significantly
from those in Illumos. Therefore, updating the vdev_file.c
to use the Illumos interfaces doesn't get you consistency
with vdev_disk.c.
2) Using the upstream patch as is would requiring implementing
compatibility code for those Solaris block device interfaces
in user and kernel space. That additional complexity could
lead to confusion and doesn't buy us anything.
For these reasons I've opted to simply move the existing vn_rdwr()
as is in to the taskq function. This has the advantage of being
low risk and easy to understand. Moving the vn_rdwr() function
in to its own taskq thread also neatly avoids the possibility of
a stack overflow.
Finally, because of the additional work which is being handled by
the free taskq the number of threads has been increased. The
thread count under Illumos defaults to 100 but was decreased to 2
in commit 08d08e due to contention. We increase it to 8 until
the contention can be address by porting Illumos #3581.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1354
`zpool status -x` should only flag errors or where the pool is
unavailable. If it imported fine but isn't using the latest features
available in the code, that's not an error.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1319
2762 zpool command should have better support for feature flags
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@57221772c3https://www.illumos.org/issues/2762
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tony Hutter
Håkan Johansson
LOLi
DHE
Christer Ekholm
Brian Behlendorf
Richard Laager
Adam Stevko
Don Brady
Richard Yao
nathancheek
Ned Bass
Colin Ian King
Hajo Möller
Turbo Fredriksson
Tim Chase
George Wilson
SenH
Ralf Ertzinger
Neil Stockbridge
Dmitry Khasanov
Steven Burgess
Tim Connors
Christopher Siden
Dominik Honnef