Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
This is a follow up commit for e03a41a60 which aimed to resolve
this same test failure. The core "problem" here is that it takes
very little space to perform a clone/snapshot/bookmark, which
means if we want these commands to reliably fail the pool must
truely have exhausted all free space.
This commit increases the number of fill iterations to try and
consume every block which we can. This still can't guarantee
the clone/snapshot/bookmark will fail, but it significantly
improves the odds. The exception was kept since it's still
not a sure thing.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12903
Under Linux when rolling back a mounted filesystem negative dentries
may not be dropped from the cache. This can result in an ENOENT
being incorrectly returned on first access. Issuing a `df` before
the unmount results in the negative dentries being invalidated and
side steps the issue.
This is solely a workaround for the test case on Linux and not
correct behavior. The core issue of invalidating negative dentries
needs to be handled with a kernel side change. This is being
tracked as issue #6143.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12898
Issue #6143
The rerefreserv_raidz test was failing on Linux because the sync being
issued doesn't guarantee a pool sync. Switch to using the sync_pool
function and remove the ZTS exception for Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12897
The build on musl needs linux/fs.h for SEEK_DATA and friends,
and sys/sysmacros.h for P2ROUNDUP. Add the needed headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#12891
With some minor tweaks several of rsend tests can be sped up
considerably without significantly reducing test coverage.
* send-c_verify_ratio: ~120s -> ~60s
* send_realloc_*_files: ~330s -> ~65s
For the send_realloc* tests this also has the advantage of removing
(most of) the linux/freebsd conditional logic. Note that for this
test more passes, and thus more incremental send/recvs, are preferable
to a larger number of files.
Total run time of the rsend test group was reduced from roughly 20 to
11 minutes in an environment similar to what's used by the CI.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12876
The rsend_007_pos test reliably fails on Linux in the cleanup
function. This is caused by an unmount error when attempting to
recursively destroy the newly received datasets. Invoking `df`
prior to the `zfs destroy` interestingly avoids the unmont error.
Why this should matter is unclear and should be investigated.
However, this minor tweak may allow us to remove the ZTS rsend
exceptions. The subsequent rsend_010_pos and rsend_011_pos
failures were a result of this initial failure. The other
"maybe" failures I was unable to reproduce and have not been
recently observed in the master branch.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5665Closes#6086Closes#6087Closes#6446Closes#12876
Provide access to file generation number on Linux.
Add test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12856
The alloc_class_* tests may fail on Linux with an EBUSY error if
`zfs destroy` is run before the `dd` process has had a chance to
terminate. Wait on the pid after the `kill -9` to make sure.
When testing I didn't observe any failures for the alloc_class
tests. Remove them from the exceptions list, the CI was used to
verify the tests pass on all platforms.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12873
Unfortunately, #11445 means while we fail gracefully now, we still
fail, unless people want to implement a complex workaround just to
support /dev/null.
So let's just use the cheap workaround in a test for now.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12872
The zpool_reopen_[1-5] tests are failing Fedora 35 with:
zpool_reopen_001_pos.ksh[64]: log_must[67]: log_pos[270]:
wait_for_resilver_end[98]: wait_for_action: line 71: func: is read only
Renaming 'func' -> 'funct' fixes the issue.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12871
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
The pam_zfs_key pam module does not enforce a minimum password
length while changing the user password and thus the users home
dataset passphrase. To not end up with a dateset `zfs load-key`
can't load the key for, `zfs load-key` should not enforce a minimum
passphrase length. This adds a test for that.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12765Closes#12651Closes#12656
Remove the generated pam service config file
`/etc/pam.d/pam_zfs_key_test` on test cleanup, since the tests
shouldn't alter system state.
While here, move the pam service config file name into a variable.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12765
The code is integrated, builds fine, runs fine, there's not really
any reason not to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12735
The l2cache device could be added twice because vdev_inuse() does not
check spa_l2cache for added devices. Make l2cache vdevs inuse checking
logic more closer to spare vdevs.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9153Closes#12689
In case if all label checksums will be invalid on any vdev, the pool
will become unimportable. The zhack with newly added cli options could
be used to restore label checksums and make pool importable again.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#2510Closes#12686
When ZFS is on root, /tmp is a ZFS. This causes zfs_list_004_neg to
fail since `zfs list` on /tmp passes when the test expects it not to.
The fix is to exclude paths that belong to ZFS.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Palash Gandhi <pbg4930@rit.edu>
Closes#12744
In case if all label checksums will be invalid on any vdev, the pool
will become unimportable. From other side zdb with -l option will not
provide any useful information why it happened. Add notifications
about corrupted label checksums.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#2509Closes#12685
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
When a parent dataset has normalization set to any value other than
"none", and a file system is created with the property "utf8only=off",
implicitly also set "normalization=none" instead of overriding the
desire for a non-UTF8 enforcing file system.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mike Swanson <mikeonthecomputer@gmail.com>
Closes#11892Closes#12038
The values of next properties: filesystem_limit, filesystem_count,
snapshot_limit, snapshot_count were returned to user as UINT64_MAX
integers in case if -p cli option is used, return 'none' value instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9306Closes#12690
It turns out, userland is much more happy with aliased property
names than the kernel is.
So let's normalize those to the expected names before we pass
them off.
Added a test case hacked up from the other recv -o/-x test that fails
on unpatched git and passes here.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12607Closes#12609
When cleaning up a test case standardize on using the convention:
datasetexists $ds && destroy_dataset $ds <flags>
By using 'destroy_dataset' instead of 'log_must zfs destroy' we ensure
that the destroy is retried in the event that a ZFS volume is busy.
This helps ensures ensure tests are fully cleaned up and prevents false
positive test failures on Linux.
Note that all of the tests which used 'zfs destroy' in cleanup have
been updated even if they don't use volumes. This was done to
clearly establish the expected convention.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12663
The useradd(8) command on my system won't accept login names with
uppercase letters in them, so adjust for that.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12665
The intention of the zfs_iter_mounted() is to traverse the dataset
and its descendants, not the snapshots. The current code can cause
a mounted snapshot to be included and thus zfs_open() on the snapshot
with ZFS_TYPE_FILESYSTEM would print confusing message such as "cannot
open 'rpool/fs@snap': snapshot delimiter '@' is not expected here".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#12447Closes#12448
Recognize when the host part of a sharenfs attribute is an ipv6
Literal and pass that through without modification.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
Closes: #11171Closes#11939Closes: #1894
In the CI environment it's possible for events to be slightly
delayed resulting in 4, instead of 5, events appearing in the
log file. This isn't a problem and should be considered a
success to avoid false positive test results.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12625
zfs send -R -i snap1 pool/ds@snap1 is an invalid invocation of zfs send
because the incremental source and target snapshots are the same. We
have an error message for this condition, but we don't make it there
because of a failed assert while iterating through the dataset's
snapshots.
Check for NULL to avoid the assert so we can make it to the error
message.
Test this form of invalid send invocation in rsend tests. Fix the
rsend_016_neg test while here: log_neg itself doesn't fail the test,
and writing to /dev/null is not supported on all Linux kernels.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11121Closes#12533
For those not already familiar with the code base it can be a
challenge to understand how the libraries are laid out. This
has sometimes resulted in functionality being added in the
wrong place. To help avoid that in the future this commit
documents the high-level dependencies for easy reference in
lib/Makefile.am. It also simplifies a few things.
- Switched libzpool dependency on libzfs_core to libzutil.
This change makes it clear libzpool should never depend
on the ioctl() functionality provided by libzfs_core.
- Moved zfs_ioctl_fd() from libzutil to libzfs_core and
renamed it lzc_ioctl_fd(). Normal access to the kmods
should all be funneled through the libzfs_core library.
The sole exception is the pool_active() which was updated
to not use lzc_ioctl_fd() to remove the libzfs_core
dependency.
- Removed libzfs_core dependency on libzutil.
- Removed the lib/libzfs/os/freebsd/libzfs_ioctl_compat.c
source file which was all dead code.
- Removed libzfs_core dependency from mkbusy and ctime
test utilities. It was only needed for some trivial
wrapper functions and that code is easy to replicate
to shed the unneeded dependency.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12602
The zvol_misc tests, in particular zvol_misc_volmode, make use of a
common udev_wait function to wait for zvol devices in /dev to quiesce
on Linux. On other platforms this function currently only sleeps for
one second before returning. This is insufficient, and
zvol_misc_volmode has been flaky on FreeBSD as a result.
Replace udev_wait with block_device_wait, passing through the optional
device parameter where possible. Rearrange a few checks to strengthen
the verifications we are making and avoid unnecessarily sleeping. We
must keep udev_wait in a couple places to pass in Github CI workflows.
Remove zvol_misc_volmode from the maybe failing tests on FreeBSD in
zts-report.py.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12583
* Add async runs for sequential_writes, random_readwrite_fixed and
random_writes
* Remove some larger block sizes that give similar results to others
* Remove nthreads == 4 from random_writes_zil test
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12576
As detailed in #12022 and #12008, it turns out the current zstd
implementation is quite nonportable, and results in various
configurations of ondisk header that only each platform can read.
So I've added a test which contains a dataset with a file written by
Linux/x86_64 and one written by FBSD/ppc64.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12030
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
This is a follow up patch for PR #12515 which addresses some
additional ZTS tests which are unreliable are should explicitly
wait for the required zvols to be available.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: @Theo13111
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12553
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
The ZTS block_device_wait helper function should use -e when waiting
for a file to appear since it will be either a block special device
or a symlink. This didn't cause any failures but when a device path
was specified the function would wait longer than needed.
Additionally update the most flakey test cases to pass the file path
to block_device_wait to try and improve the test reliability. The
udev behavior on Fedora in particular can result in frequent false
positives.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12515
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12432
Many things has changed since previous default was set many years ago.
Nowadays 8KB does not allow adequate compression or even decent space
efficiency on many of pools due to 4KB disk physical block rounding,
especially on RAIDZ and DRAID. It effectively limits write throughput
to only 2-3GB/s (250-350K blocks/s) due to sync thread, allocation,
vdev queue and other block rate bottlenecks. It keeps L2ARC expensive
despite many optimizations and dedup just unrealistic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12406
The redacted_send tests make use of a $tmpdir variable, except in
redacted_send/redacted_panic the variable is never defined.
Use $TEST_BASE_DIR instead.
Clean up the stream file after the test.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12455
- Bail out early if we're running the perf tests and forget to
specify disks.
- Allow perf tests to run with any number of disks.
- Remove weekly vs. nightly settings
- Move variables with common values to perf.shlib
- Use zinject to clear the ARC over export/import
- Fix dbuf cache size calculation
When the meaning of `dbuf_cache_max_bytes` changed, the performance
test that covers the dbuf cache started to fail. The test would try to
write files for the test using the max possible size of the cache,
inevitably filling the pool and failing. This change uses
`dbuf_cache_shift` to correctly calculate the dbuf cache size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12408
In l2arc_add_vdev() first decide whether the device is eligible for
L2ARC rebuild or whole device trim and then add it to the list of cache
devices. Otherwise l2arc_feed_thread() might already start writing on
the device invalidating previous content as l2ad_hand = l2ad_start.
However l2arc_rebuild_vdev() needs the device present in the cache
device list to figure out its l2arc_dev_t. Fix this by moving most of
l2arc_rebuild_vdev() in a new function l2arc_rebuild_dev() which does
not need to search in the cache device list.
In contrast to l2arc_add_vdev() we do not have to worry about
l2arc_feed_thread() invalidating previous content when onlining a
cache device. The device parameters (l2ad*) are not cleared when
offlining the device and writing new buffers will not invalidate
all previous content. In worst case only buffers that have not had
their log block written to the device will be lost.
Retire persist_l2arc_00{4,5,8} tests since they cover code already
covered by the remaining ones. Test persist_l2arc_006 is renamed to
persist_l2arc_004 and persist_l2arc_007 is renamed to persist_l2arc_005.
Fix a typo in persist_l2arc_004, and remove an assertion that is not
always true from l2arc_arcstats_pos. Also update an assertion in
persist_l2arc_005 and explain why in a comment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12365
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This enables ZED to auto-online vdevs that are not wholedisk managed by
ZFS.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Unlike most other properties the 'compatibility' property is stored
in the pool config object and not the DMU_OT_POOL_PROPS object.
This had the advantage that the compatibility information is available
without needing to fully import the pool (it can be read with zdb).
However, this means we need to make sure to update both the copy of
the config in the MOS and the cache file. This wasn't being done.
This commit adds a call to spa_async_request() to ensure the copy of
the config in the cache file gets updated as well as the one stored
in the pool. This same change is made for the 'comment' property
which suffers from the same inconsistency.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Colm Buckley <colm@tuatha.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12261Closes#12276
zstreamdump was replaced with "zstream dump"; let's stop using the
old name, compat symlink or no.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12277
There are at least two interpretations of basename(3),
in addition to both functions being allowed to /both/ return a static
buffer (unsuitable in multi-threaded environments) /and/ raze the input
(which encourages overallocations, at best)
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12105
Commit 86b5f4c12 added a new zfs_clone_livelist_dedup.ksh test case
but didn't include it in the Makefile.am. This results in the test
not being included in the dist tarball so it's never run by the CI.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #12224
Update the logic to handle the dedup-case of consecutive
FREEs in the livelist code. The logic still ensures that
all the FREE entries are matched up with a respective
ALLOC by keeping a refcount for each FREE blkptr that we
encounter and ensuring that this refcount gets to zero
by the time we are done processing the livelist.
zdb -y no longer panics when encountering double frees
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11480Closes#12177
On FreeBSD 14, these two tests started erroring out like the
objects they're attempting to examine don't exist.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12165
This checks every file it checked (and a few more),
but explicitly instead of "if it works it works" best-effort
(which wasn't that good anyway)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#10512Closes#12101
The change correctly handles BrokenPipeError and improves the
associated tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12037Closes#12036
verify_slog_support no longer applies to ZFS since slog support
is always available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#12092
According to POSIX.1, "vfork() has the same effect as fork(2),
except that the behavior is undefined if the process created by vfork()
either modifies any data other than a variable of type pid_t
used to store the return value from vfork(), [...],
or calls any other function before successfully calling _exit(2)
or one of the exec(3) family of functions."
These do all three, and work by pure chance
(or maybe they don't, but we blisfully don't know).
Either way: bad idea to call vfork() from C,
unless you're the standard library, and POSIX.1-2008 removes it entirely
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12015
This change addresses two distinct scenarios which are possible
when performing a sequential resilver to a dRAID pool with vdevs
that contain silent unknown damage. Which in this circumstance
took the form of the devices being intentionally overwritten with
zeros. However, it could also result from a device returning incorrect
data while a sequential resilver was in progress.
Scenario 1) A sequential resilver is performed while all of the
dRAID vdevs are ONLINE and there is silent damage present on the
vdev being resilvered. In this case, nothing will be repaired
by vdev_raidz_io_done_reconstruct_known_missing() because
rc->rc_error isn't set on any of the raid columns. To address
this vdev_draid_io_start_read() has been updated to always mark
the resilvering column as ESTALE for sequential resilver IO.
Scenario 2) Multiple columns contain silent damage for the same
block and a sequential resilver is performed. In this case it's
impossible to generate the correct data from parity unless all of
the damaged columns are being sequentially resilvered (and thus
only good data is used to generate parity). This is as expected
and there's nothing which can be done about it. However, we need
to be careful not to make to situation worse. Since we can't
verify the data is actually good without a checksum, we must
only repair the devices which are being sequentially resilvered.
Otherwise, an incorrect repair to a device which previously
contained good data could effectively lock in the damage and
make reconstruction impossible. A check for this was added to
vdev_raidz_io_done_verified() along with a new test case.
Lastly, this change updates the redundancy_draid_spare1 and
redundancy_draid_spare3 test cases to be more representative
of normal dRAID replacement operation. Specifically, what we
care about is that the scrub run after a sequential resilver
does not find additional blocks which need repair. This would
indicate the sequential resilver failed to rebuild a section of
one of the devices. Note also the tests were switched to using
the verify_pool() function which still checks for checksum errors.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12061
Commit d1d4769 takes into account the encryption key version to
decide if the local_mac could be zeroed out. However, this could lead
to failure mounting encrypted datasets created with intermediate
versions of ZFS encryption available in master between major releases.
In order to prevent this situation revert d1d4769 pending a more
comprehensive fix which addresses the mount failure case.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11294
Issue #12025
Issue #12300Closes#12033
Add support for http and https to the keylocation properly to
allow encryption keys to be fetched from the specified URL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #9543Closes#9947Closes#11956
When dRAID performs a normal read operation only the data columns
in the raid map are read from disk. This is enough information to
calculate the checksum, verify it, and return the needed data to the
application. It's only in the event of a checksum failure that the
additional parity and any empty columns must be read since they are
required for parity reconstruction.
Reading these additional columns is handled by vdev_raidz_read_all()
which calls vdev_draid_map_alloc_empty() to expand the raid_map_t
and submit IOs for the missing columns. This all works correctly,
but it fails to account for any "short" columns. These are data
columns which are padded with a empty skip sector at the end.
Since that empty sector is not needed for a normal read it's not
read when columns is first read from disk. However, like the parity
and empty columns the skip sector is needed to perform reconstruction.
The fix is to mark any "short" columns as never being read by clearing
the rc_tried flag when expanding the raid_map_t. This will cause
the entire column to re-read from disk in the event of a checksum
failure allowing the self-healing functionality to repair the block.
Note that this only effects the self-healing feature because when
scrubbing a pool the parity, data, and empty columns are all read
initially to verify their contents. Furthermore, only blocks which
contain "short" columns would be effected, and only when the memory
backing the skip sector wasn't already zeroed out.
This change extends the existing redundancy_raidz.ksh test case to
verify self-healing (as well as resilver and scrub). Then applies
the same test case to dRAID with a slightly modified version of
the test script called redundancy_draid.ksh. The unused variable
combrec was also removed from both test cases.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12010
Afterward, git grep ZoL matches:
* README.md: * [ZoL Site](https://zfsonlinux.org)
- Correct
* etc/default/zfs.in:# ZoL userland configuration.
- Changing this would induce a needless upgrade-check,
if the user has modified the configuration;
this can be updated the next time the defaults change
* module/zfs/dmu_send.c: * ZoL < 0.7 does not handle [...]
- Before 0.7 is ZoL, so fair enough
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11956
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11970
Receiving datasets while blanket inheriting properties like zfs
receive -x mountpoint can generally be desirable, e.g. to avoid
unexpected mounts on backup hosts.
Currently this will fail to receive zvols due to the mountpoint
property being applicable to filesystems only. This limitation
currently requires operators to special-case their minds and tools
for zvols.
This change gets rid of this limitation for inherit (-x) by
Spiting up the dataset type handling: Warnings for inheriting (-x),
errors for overriding (-o).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#11416Closes#11840Closes#11864
- Add additional logging to provide more information about why the
test failed. This including logging more of the individual commands
and the contents and differences of the record files on failure.
- Updated get_vdevs() to properly exclude all top-level vdevs
including raidz3 and draid[1-3].
- Replaced gnudd with dd. This is the only remaining place in the
test suite gnudd is used and it shouldn't be needed.
- The refill_test_env function expects the pool as the first argument
but never sets the pool variable.
- Only fill the test pools to 50% of capacity instead of 75% to help
speed up the tests.
- Fix replace_missing_devs() calculation, MINDEVSIZE should be
MINVDEVSIZE.
- Fix damage_devs() so it overwrites almost all of the device so
we're guaranteed to damage filesystem blocks.
- redundancy_stripe.ksh should not use log_mustnot to check if the
pool is healthy since the return value may be misinterpreted.
Just perform a normal conditional check and log the failure.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11906
It's been observed in the CI that the required 25% of obsolete bytes
in the mapping can be to high a threshold for this test resulting in
condensing never being triggered and a test failure. To prevent these
failures make the existing zfs_condense_indirect_obsolete_pct tuning
available so the obsolete percentage can be reduced from 25% to 5%
during this test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11869
A tentative implementation and discussion was done in #5285.
According to it a send --skip-missing|-s flag has been added.
In a replication stream, when there are snapshots missing in
the hierarchy, if -s is provided print a warning and ignore
dataset (and its children) instead of throwing an error
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pablo Correa Gómez <ablocorrea@hotmail.com>
Closes#11710
Kill the removal operation on every platform, not just Linux.
The test has been fixed and is now stable on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11856
Just as delay zevents can flood the zevent pipe when a vdev becomes
unresponsive, so do the deadman zevents.
Ratelimit deadman zevents according to the same tunable as for delay
zevents.
Enable deadman tests on FreeBSD and add a test for deadman event
ratelimiting.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11786
get_clones_string currently returns an empty string for filesystem
snapshots which have no clones. This breaks parsable `zfs get` output as
only three columns are output, instead of 4.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Fiddaman <github@m.fiddaman.uk>
Co-authored-by: matt <matt@fiddaman.net>
Closes#11837
The pool_checkpoint tests may incorrectly fail because several of
them invoke zdb for an imported pool. In this scenario it's not
unexpected for zdb to fail if the pool is modified. To resolve
this these zdb checks are now done after the pool has been exported.
Additionally, the default cleanup functions assumed the pool would
be imported when they were run. If this was not the case they're
exit early and fail to cleanup all of the test state causing
subsequent tests to fail. Add a check to only destroy the pool
when it is imported.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11832
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
200ms time-out is relatively long, but if we already hit the cap,
then we'll likely be able to spawn multiple new jobs when we wake up
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11807
Nothing bad happens if a prefix of your pool name matches a disk name.
This is a bit of a silly restriction at this point.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11781Closes#11813
Commit 235a85657 introduced a regression in evaluation of POSIX modes
that require group DENY entries in the internal ZFS ACL. An example
of such a POSX mode is 007. When write_implies_delete_child is set,
then ACE_WRITE_DATA is added to `wanted_dirperms` in prior to calling
zfs_zaccess_common(). This occurs is zfs_zaccess_delete().
Unfortunately, when zfs_zaccess_aces_check hits this particular DENY
ACE, zfs_groupmember() is checked to determine whether access should be
denied, and since zfs_groupmember() always returns B_TRUE on Linux and
so this check is failed, resulting ultimately in EPERM being returned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#11760
This change adds a new test that covers a bug fix in the binary search
in the redacted send resume logic that causes a kernel panic.
The bug was fixed in https://github.com/openzfs/zfs/pull/11297.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Palash Gandhi <palash.gandhi@delphix.com>
Closes#11764
Create a new section of tests to run with acltype=off.
For now the only test we have is for the DOS mode READONLY attribute on
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11734
You can't use user_run to eval ksh functions defined in libtest unless
you include libtest in the user shell.
Fix xattr_003_neg by:
* include libtest in the user shell
* *then* run get_xattr
* assert this fails
* use variables for filenames so they don't change in the user's shell
* don't log the contents of /etc/passwd
* cleanup all byproducts
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
The current user_run often does not work as expected. Commands are run
in a different shell, with a different environment, and all output is
discarded.
Simplify user_run to retain the current environment, eliminate eval,
and feed the command string into ksh. Enhance the logging for
user_run so we can see out and err.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
A few deadman tunables ended up in the wrong sysctl node.
Move them to vfs.zfs.deadman.*
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11715
events_002 exercises the ZED, ensuring that it neither misses events,
nor reporting events twice.
On slow test hardware, some of the timeouts are insufficient to allow
the ZED to properly settle. Conversely, on fast hardware these same
timeouts are too long, unnecessarily slowing the test run.
Instead of using a fixed timeout, wait for the expected final event
before returning. Additionally, wait with a timeout for unexpected
events to avoid missing them if they show up late.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11703
* Restore original kern.corefile value after the test.
* Don't leave behind a frozen pool.
* Clean up leftover vdev files.
* Make zpool_002_pos and zpool_003_pos consistent in their handling of
core files while here.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11694
When a device which is actively trimming or initializing becomes
FAULTED, and therefore no longer writable, cancel the active
TRIM or initialization. When the device is merely taken offline
with `zpool offline` then stop the operation but do not cancel it.
When the device is brought back online the operation will be
resumed if possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11588
Several of the TRIM tests were based of the initialize tests and
then adapted for TRIM. The zpool_trim_start_and_cancel_pos.ksh
test was intended to be one such test but it was overlooked and
actually never adapted. Update it accordingly.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11649
The behavior of a NULL fromsnap was inadvertently changed for a doall
send when the send/recv logic in libzfs was updated. Restore the
previous behavior by correcting send_iterate_snap() to include all
the snapshots in the nvlist for this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cedric Maunoury <cedric.maunoury@gmail.com>
Closes#11608
Fix regression seen in issue #11545 where checksum errors
where not being counted or showing up in a zpool event.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11609
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
There are two issues that don't allow ZFS to be compiled using uClibc.
`backtrace()`, and `program_invocation_short_name` as a `const`.
This patch adds uClibc to the conditionals in the same way there are
already for Glibc for `backtrace()`; and removes the external param
`program_invocation_short_name` because its only used here for the
whole project.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: José Luis Salvador Rufo <salvador.joseluis@gmail.com>
Closes#11600
All tests need to be included in the Makefiles.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11541
While you can use zdb -R poolname vdev:offset:[<lsize>/]<psize>[:flags]
to extract individual DVAs from a vdev, it would be handy for be able
copy an entire file out of the pool.
Given a file or object number, add support to copy the contents to a
file. Useful for debugging and recovery.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11027
If there is no scsi_debug module, then this test
must be skipped, in this case cleanup routine should
be prepared for absent pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11534
When scrubbing, (non-sequential) resilvering, or correcting a checksum
error using RAIDZ parity, ZFS should heal any incorrect RAIDZ parity by
overwriting it. For example, if P disks are silently corrupted (P being
the number of failures tolerated; e.g. RAIDZ2 has P=2), `zpool scrub`
should detect and heal all the bad state on these disks, including
parity. This way if there is a subsequent failure we are fully
protected.
With RAIDZ2 or RAIDZ3, a block can have silent damage to a parity
sector, and also damage (silent or known) to a data sector. In this
case the parity should be healed but it is not.
The problem can be noticed by scrubbing the pool twice. Assuming there
was no damage concurrent with the scrubs, the first scrub should fix all
silent damage, and the second scrub should be "clean" (`zpool status`
should not report checksum errors on any disks). If the bug is
encountered, then the second scrub will repair the silently-damaged
parity that the first scrub failed to repair, and these checksum errors
will be reported after the second scrub. Since the first scrub repaired
all the damaged data, the bug can not be encountered during the second
scrub, so subsequent scrubs (more than two) are not necessary.
The root cause of the problem is some code that was inadvertently added
to `raidz_parity_verify()` by the DRAID changes. The incorrect code
causes the parity healing to be aborted if there is damaged data
(`rc_error != 0`) or the data disk is not present (`!rc_tried`). These
checks are not necessary, because we only call `raidz_parity_verify()`
if we have the correct data (which may have been reconstructed using
parity, and which was verified by the checksum).
This commit fixes the problem by removing the incorrect checks in
`raidz_parity_verify()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11489Closes#11510
- refactor cleanup routines into common kshlib zpool_export_cleanup func
- don't require physical disks to test, just use files
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11518
Instead of just failing, indicate the expected and actual value and
source as a NOTE. Tests using this failed in an earlier version of
the changeset and this information helped find the cause.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11517
There is an identical definition in zfs_set_common.kshlib already.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11516
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11503
Provide a basic test coverage for io_uring I/O.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11497
In FreeBSD the struct uio was just a typedef to uio_t. In order to
extend this struct, outside of the definition for the struct uio, the
struct uio has been embedded inside of a uio_t struct.
Also renamed all the uio_* interfaces to be zfs_uio_* to make it clear
this is a ZFS interface.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11438
Prior to util-linux 2.36.2, if a file or directory in the
current working directory was named 'dataset' then mount(8)
would prepend the current working directory to the dataset.
Eventually, we should be able to drop this workaround.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11295Closes#11462
As described in #11445, the kernel interface kernel_{read,write} no
longer act on special devices. In the ZTS, zfs send and receive are
tested by piping to these devices, leading to spurious failures (for
positive tests) and may mask errors (for negative tests).
Until a more permanent mechanism to address this deficiency is
developed, clean up the output from the ZTS by avoiding directly piping
to or from /dev/null and /dev/zero.
For /dev/zero input, simply use a pipe: `cat </dev/zero |` .
However, for /dev/null output, the shell semantics for pipe failures
means that zfs send error codes will be masked by the successful
`| cat >/dev/null` command execution. In that case, use a temporary
file under $TEST_BASE_DIR for output in favor.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11478
The zfs_rollback_001 test modifies files in a temporary, test dataset
repeatedly. Before each iteration, any preexisting dataset is removed,
after unmounted with umount -f, if necessary.
Add a short delay after the forced unmount, avoiding a race that can
prevent zfs destroy from succeeding, leading to a test failure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11451
if pool root is not mounted, then zpool umount in next test will leave
dataset mountpoint directory around and next zfs mount -a will fail
with error: cannot mount '/testpool': directory is not empty
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11417
Build error on illumos with gcc 10 did reveal:
In function 'dmu_objset_refresh_ownership':
../../common/fs/zfs/dmu_objset.c:857:25: error: implicit conversion
from 'boolean_t' to 'ds_hold_flags_t' {aka 'enum ds_hold_flags'}
[-Werror=enum-conversion]
857 | dsl_dataset_disown(ds, decrypt, tag);
| ^~~~~~~
cc1: all warnings being treated as errors
libzfs_input_check.c: In function 'zfs_ioc_input_tests':
libzfs_input_check.c:754:28: error: implicit conversion from
'enum dmu_objset_type' to 'enum lzc_dataset_type'
[-Werror=enum-conversion]
754 | err = lzc_create(dataset, DMU_OST_ZFS, NULL, NULL, 0);
| ^~~~~~~~~~~
cc1: all warnings being treated as errors
The same issue is present in openzfs, and also the same issue about
ds_hold_flags_t, which currently defines exactly one valid value.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11406
Consider the test to be a success as long as the initializing pattern
is found at least once per metaslab. This indicates that at least
part of the free space was initialized. Ideally we'd check that the
pattern was written to all free space but that's much trickier so this
check is a reasonable compromise.
Using a here-string to feed the loop in this test causes an empty
string to still trigger the loop so we miss the `spacemaps=0` case.
Pipe into the loop instead.
While here, we can use `zpool wait -t initialize $TESTPOOL` to wait for
the pool to initialize.
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11365
The space in special devices is not included in spa_dspace (or
dsl_pool_adjustedsize(), or the zfs `available` property). Therefore
there is always at least as much free space in the normal class, as
there is allocated in the special class(es). And therefore, there is
always enough free space to remove a special device.
However, the checks for free space when removing special devices did not
take this into account. This commit corrects that.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11329
Use the correct return type for getopt otherwise clang complains
about tautological-constant-out-of-range-compare.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11359
When removing and subsequently reattaching a vdev, CKSUM errors may
occur as vdev_indirect_read_all() reads from all children of a mirror
in case of a resilver.
Fix this by checking whether a child is missing the data and setting a
flag (ic_error) which is then checked in vdev_indirect_repair() and
suppresses incrementing the checksum counter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11277
Follow up fix for 0cb40fa3. Remove unused variables, don't source
unused libs and add missed cleanup.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11311
Canonicalization, the source of the trouble, was disabled in 9000a9f.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11295
Otherwise trim may finish before progress checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11296
Occasionally an out of memory error is hit by this test case
when mounting the filesystems. Try and reduce the likelihood
of this occurring by reducing the thread count from 100 to 50.
It also has the advantage of slightly speeding up the test.
cannot mount 'testpool/testfs3/79': Cannot allocate memory
filesystem successfully created, but not mounted
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11283
When sending raw encrypted datasets the user space accounting is present
when it's not expected to be. This leads to the subsequent mount failure
due a checksum error when verifying the local mac.
Fix this by clearing the OBJSET_FLAG_USERACCOUNTING_COMPLETE and reset
the local mac. This allows the user accounting to be correctly updated
on first mount using the normal upgrade process.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10523Closes#11221
`zpool create -n` fails to list cache and spare vdevs.
`zpool add -n` fails to list spare devices.
`zpool split -n` fails to list `special` and `dedup` labels.
`zpool add -n` and `zpool split -n` shouldn't list hole devices.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11122Closes#11167
Add -u option to 'zfs create' that prevents file system from being
automatically mounted. This is similar to the 'zfs receive -u'.
Authored by: pjd <pjd@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@35c58230e2
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Ported-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11254
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
The custom zpl_show_devname() helper should translate spaces in
to the octal escape sequence \040. The getmntent(2) function
is aware of this convention and properly translates the escape
character back to a space when reading the fsname.
Without this change the `zfs mount` and `zfs unmount` commands
incorrectly detect when a dataset with a name containing spaces
is mounted.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11182Closes#11187
The microzap hash can sometimes be zero for single digit snapnames.
The zap cursor can then have a serialized value of two (for . and ..),
and skip the first entry in the avl tree for the .zfs/snapshot directory
listing, and therefore does not return all snapshots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Tony Perkins <tperkins@datto.com>
Closes#11039
Convert dynamic allocation to static buffer, simplify parse_dataset
function return path. Add tests specific to the mount helper.
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11098
Add a new test case which corrupts all level 1 block in a file.
Then verifies that corruption is detected and repaired.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
The second part of list_file_blocks transforms the object description
output by zdb -ddddd $ds $objnum into a stream of lines of the form
"level path offset length" for the indirect blocks in the given file.
The current code only works for the first copy of L0 blocks. L1 and
L2 indirect blocks have more than one copy on disk.
Add one more -d to the zdb command so we get all block copies and
rewrite the transformation to match more than L0 and output all DVAs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
The first part of list_file_blocks transforms the pool configuration
output by zdb -C $pool into shell code to set up a shell variable,
VDEV_MAP, that maps from vdev id to the underlying vdev path. This
variable is a simple indexed array. However, the vdev id in a DVA is
only the id of the top level vdev.
When the pool is mirrored, the top level vdev is a mirror and its
children are the mirrored devices. So, what we need is to map from
the top level vdev id to a list of the underlying vdev paths.
ist_file_blocks does not need to work for raidz vdevs, so we can
disregard that case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11141
The expected variance for this test case was originally set at 10%
based on local testing. Additional testing via the CI has show it
can be as large as 11%. Increase the expected maximum to 12% to
prevent this test from incorrectly failing.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11148
The events_001_pos.ksh test case can fail because it's possible,
and correct, for the config_sync event to be posted after the last
"expected" event. To accommodate this the run_and_verify() function
has been updated to wait for all non-history events, not just the
last event. This does not increase the run time of the test as
long as all the events do get generated.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11147
Refer to the correct section or alternative for FreeBSD and Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11132
Previously, xattr_004_pos would create files with xattrs on both
tmpfs and ext2, and then copy them to zfs to verify that their
xattrs were preserved. However tmpfs doesn't support xattrs.
This was never noticed until Fedora 33. In Fedora 32 and older,
/tmp was on the root partition (like ext4), whereas on Fedora 33
/tmp is actually tmpfs. That caused this test to fail on Fedora 33.
This fix updates the test to only create the file on ext2, not tmpfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11133
The current l2_misses accounting behavior treats all reads to pools
without a configured l2arc as an l2arc miss, IFF there is at least
one other pool on the system which does have an l2arc configured.
This makes it extremely hard to tune for an improved l2arc hit/miss
ratio because this ratio will be modulated by reads from pools which
do not (and should not) have l2arc devices; its upper limit will
depend on the ratio of reads from l2arc'd pools and non-l2arc'd pools.
This PR prevents ARC reads affecting l2arc stats (n.b. l2_misses is
the only relevant one) where the target spa doesn't have an l2arc.
Includes new test - l2arc_l2miss_pos.ksh
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#10921
ZED will log zevents summaries to the syslog, however the log entries
tend to drop event details that can be useful for diagnosis. This is
especially true for ereport events, like io, checksum, and delay.
Update the all-syslog.sh script to log additional event information.
Add an optional config option, ZED_SYSLOG_DISPLAY_GUIDS, to zed.rc
for choosing GUIDs over names for pool and vdev.
Change the default ZED_SYSLOG_SUBCLASS_EXCLUDE to exclude history_event
events. These events tend to be frequent, convey no meaningful info,
and are already logged in the zpool history.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10967
This is a follow up fix for commit 0fdd6106bb. The VERIFY is
only true when we haven't hit an error code path. See added
test case for a reproducer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11048
The acltype property is currently hidden on FreeBSD and does not
reflect the NFSv4 style ZFS ACLs used on the platform. This makes it
difficult to observe that a pool imported from FreeBSD on Linux has a
different type of ACL that is being ignored, and vice versa.
Add an nfsv4 acltype and expose the property on FreeBSD.
Make the default acltype nfsv4 on FreeBSD.
Setting acltype to an unhanded style is treated the same as setting
it to off. The ACLs will not be removed, but they will be ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10520
A zpool_influxdb command is introduced to ease the collection
of zpool statistics into the InfluxDB time-series database.
Examples are given on how to integrate with the telegraf
statistics aggregator, a companion to influxdb.
Finally, a grafana dashboard template is included to show
how pool latency distributions can be visualized in a
ZFS + telegraf + influxdb + grafana environment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Elling <Richard.Elling@RichardElling.com>
Closes#10786
The value of zp is used without having been initialized under some
conditions. Initialize the pointer to NULL.
Add a regression test case using chown in acl/posix. However, this is
not enough because the setup sets xattr=sa, which means zfs_setattr_dir
will not be called. Create a second group of acl tests in acl/posix-sa
duplicating the acl/posix tests with symlinks, and remove xattr=sa from
the original acl/posix tests. This provides more coverage for the
default xattr=on code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10043Closes#11025
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
Don't direct stdout and stderr of dd to $TEST_BASE_DIR/null,
direct it to /dev/null.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11026
With procfs_list kstats implemented for FreeBSD, dbufs are now exposed
as kstat.zfs.misc.dbufs.
On FreeBSD, dbufstats can use the sysctl instead of procfs when no
input file has been given.
Enable the dbufstats tests on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11008
Instead of relying on arbitrary timers after pool export/import or cache
device off/online rely on arcstats. This makes the L2ARC tests more
robust. Also cleanup some functions related to persistent L2ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10983
This causes "zfs send -vt ..." to fail with:
cannot resume send: Unknown error 1030
It turns out that some of the name/value pairs in the verification
list for zfs_ioc_send_space(), zfs_keys_send_space, had the wrong
name, so the ioctl got kicked out in zfs_check_input_nvpairs().
Update the names accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10978
When an invalid incremental send is requested where the "to" ds is
before the "from" ds, make sure to drop the reference to the pool
and the dataset before returning the error.
Add an assert on FreeBSD to make sure we don't hold any locks after
returning from an ioctl.
Add some test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10919
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
Prefer acltype=off|posix, retaining the old names as aliases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10918
nvlist does allow us to support different data types and systems.
To encapsulate user data to/from nvlist, the libzfsbootenv library is
provided.
Reviewed-by: Arvind Sankar <nivedita@alum.mit.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10774
Currently the ARC state (MFU/MRU) of cached L2ARC buffer and their
content type is unknown. Knowing this information may prove beneficial
in adjusting the L2ARC caching policy.
This commit adds L2ARC arcstats that display the aligned size
(in bytes) of L2ARC buffers according to their content type
(data/metadata) and according to their ARC state (MRU/MFU or
prefetch). It also expands the existing evict_l2_eligible arcstat to
differentiate between MFU and MRU buffers.
L2ARC caches buffers from the MRU and MFU lists of ARC. Upon caching a
buffer, its ARC state (MRU/MFU) is stored in the L2 header
(b_arcs_state). The l2_m{f,r}u_asize arcstats reflect the aligned size
(in bytes) of L2ARC buffers according to their ARC state (based on
b_arcs_state). We also account for the case where an L2ARC and ARC
cached MRU or MRU_ghost buffer transitions to MFU. The l2_prefetch_asize
reflects the alinged size (in bytes) of L2ARC buffers that were cached
while they had the prefetch flag set in ARC. This is dynamically updated
as the prefetch flag of L2ARC buffers changes.
When buffers are evicted from ARC, if they are determined to be L2ARC
eligible then their logical size is recorded in
evict_l2_eligible_m{r,f}u arcstats according to their ARC state upon
eviction.
Persistent L2ARC:
When committing an L2ARC buffer to a log block (L2ARC metadata) its
b_arcs_state and prefetch flag is also stored. If the buffer changes
its arcstate or prefetch flag this is reflected in the above arcstats.
However, the L2ARC metadata cannot currently be updated to reflect this
change.
Example: L2ARC caches an MRU buffer. L2ARC metadata and arcstats count
this as an MRU buffer. The buffer transitions to MFU. The arcstats are
updated to reflect this. Upon pool re-import or on/offlining the L2ARC
device the arcstats are cleared and the buffer will now be counted as an
MRU buffer, as the L2ARC metadata were not updated.
Bug fix:
- If l2arc_noprefetch is set, arc_read_done clears the L2CACHE flag of
an ARC buffer. However, prefetches may be issued in a way that
arc_read_done() is bypassed. Instead, move the related code in
l2arc_write_eligible() to account for those cases too.
Also add a test and update manpages for l2arc_mfuonly module parameter,
and update the manpages and code comments for l2arc_noprefetch.
Move persist_l2arc tests to l2arc.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10743
Duplicate io and checksum ereport events can misrepresent that
things are worse than they seem. Ideally the zpool events and the
corresponding vdev stat error counts in a zpool status should be
for unique errors -- not the same error being counted over and over.
This can be demonstrated in a simple example. With a single bad
block in a datafile and just 5 reads of the file we end up with a
degraded vdev, even though there is only one unique error in the pool.
The proposed solution to the above issue, is to eliminate duplicates
when posting events and when updating vdev error stats. We now save
recent error events of interest when posting events so that we can
easily check for duplicates when posting an error.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10861
Use ZFS_MODULE_PARAM for cross-platform tunables in spa_stats.c, and
add update tunables.cfg in tests for the newly supported ones.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10858
Allow to rename file systems without remounting if it is possible.
It is possible for file systems with 'mountpoint' property set to
'legacy' or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even
mounted back.
This introduces layering violation, as we need to update
'f_mntfromname' field in statfs structure related to mountpoint (for
the dataset we are renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even
cleaner way - in ZFS-only configuration root file system is ZFS file
system with 'mountpoint' property set to 'legacy'. If root dataset is
named system/rootfs, we can snapshot it (system/rootfs@upgrade), clone
it (system/oldrootfs), update FreeBSD and if it doesn't boot we can
boot back from system/oldrootfs and rename it back to system/rootfs
while it is mounted as /. Before it was not possible, because
unmounting / was not possible.
Authored by: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: Matt Macy <mmacy@freebsd.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10839
The root cause of the issue is that we only occasionally do as the
comments in the code suggest and actually ignore the %recv dataset when
it comes to filesystem limit tracking. Specifically, the only time we
ignore it is when initializing the filesystem and snapshot limit values;
when creating a new %recv dataset or deleting one, we always update
the bookkeeping. This causes a problem if you init the fs count on a
filesystem that already has a %recv dataset, since the bookmarking
will be decremented but not incremented. This is resolved in this
patch by simply always tracking the %recv dataset as a child.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10791
FreeBSD doesn't have an equivalent to udevadm settle, so we have been
resorting to a three second sleep to wait for device changes to take
effect. This is far from ideal.
We are mainly waiting for volmode=geom zvols to appear in /dev, so as
a hack, reading the geom config will have the desired effect of
quiescing the geom state.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10768
This change umounts client's NFS mount after each test so we can avoid
two sporadic issues:
1) client NFS stale mount and
2) zpool export and zpool destroy failed due to dataset busy
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#10767
This is a follow on to PR #10688 where `zfs share -a` allows the
sharing of canmount=noauto datasets if they are mounted. However,
when a dataset with canmount=noauto is not mounted, the command
should also purge any existing entries from the exports file.
Otherwise, after a reboot, the nfs server attempts to export the
underlying mountpath, not the dataset. This can lead to a hard hang
for existing client mounts.
Instead of just skipping the adding of an export if not mounted
and canmount=noauto, have it also remove an existing export of the
dataset so that, after a reboot, we don't export an unmounted dataset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10747
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
Due to commit d48091d a removed device is now explicitly offlined by
the ZED if no spare is available, rather than the letting ZFS detect
it as UNAVAIL. This broke auto-replacing of whole-disk devices, as
described in issue #10577. In short, when a new device is reinserted
in the same slot, the ZED will try to ONLINE it without letting ZFS
recreate the necessary partition table.
This change simply avoids setting the device OFFLINE when removed if
no spare is available (or if spare_on_remove is false). This change
has been left minimal to allow it to be backported to 0.8.x release.
The auto_offline_001_pos ZTS test has been updated accordingly.
Some follow up work is planned to update the ZED so it transitions
the vdev to a REMOVED state. This is a state which has always
existed but there is no current interface the ZED can use to
accomplish this. Therefore it's being left to a follow up PR.
Reviewed-by: Gionatan Danti <g.danti@assyoma.it>
Co-authored-by: Gionatan Danti <g.danti@assyoma.it>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10577Closes#10730
When reading compressed blocks from the L2ARC, with
compressed ARC disabled, arc_hdr_size() returns
LSIZE rather than PSIZE, but the actual read is PSIZE.
This causes l2arc_read_done() to compare the checksum
against the wrong size, resulting in checksum failure.
This manifests as an increase in the kstat l2_cksum_bad
and the read being retried from the main pool, making the
L2ARC ineffective.
Add new L2ARC tests with Compressed ARC enabled/disabled
Blocks are handled differently depending on the state of the
zfs_compressed_arc_enabled tunable.
If a block is compressed on-disk, and compressed_arc is enabled:
- the block is read from disk
- It is NOT decompressed
- It is added to the ARC in its compressed form
- l2arc_write_buffers() may write it to the L2ARC (as is)
- l2arc_read_done() compares the checksum to the BP (compressed)
However, if compressed_arc is disabled:
- the block is read from disk
- It is decompressed
- It is added to the ARC (uncompressed)
- l2arc_write_buffers() will use l2arc_apply_transforms() to
recompress the block, before writing it to the L2ARC
- l2arc_read_done() compares the checksum to the BP (compressed)
- l2arc_read_done() will use l2arc_untransform() to uncompress it
This test writes out a test file to a pool consisting of one disk
and one cache device, then randomly reads from it. Since the arc_max
in the tests is low, this will feed the L2ARC, and result in reads
from the L2ARC.
We compare the value of the kstat l2_cksum_bad before and after
to determine if any blocks failed to survive the trip through the
L2ARC.
Sponsored-by: The FreeBSD Foundation
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#10693
The 'zfs share -a' currently skips any filesystems which
have 'canmount=noauto' set. This behavior is unexpected since the
one would expect 'zfs share -a' to share any mounted filesystem
that has the 'sharenfs' property already set.
This changes the behavior of 'zfs share -a' to allow the sharing
of 'canmount=noauto' datasets if they are mounted.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-issue: DLPX-71313
Closes#10688
Bring zfs-tests.sh in to compliance with the other scripts
by converting it /bin/sh for to avoid a dependency on bash.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10640
zfs_jail was not using zfs_ioctl so failed to map the IOC number
correctly. Use zfs_ioctl to perform the jail ioctl and add a test
case for FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10658
FreeBSD recently integrated a change which causes \s in a regex to
throw an error instead of silently being misinterpreted as an s.
Change the regex in zpool_colors.ksh to use [[:space:]].
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10651
When a clone is promoted, its livelist is no longer accurate, so it is
discarded. If the clone's origin is also a clone (i.e. we are promoting
a clone of a clone), then the origin's livelist is also no longer
accurate, so it should be discarded, but the code doesn't actually do
that.
Consider a pool with:
* Filesystem A
* Clone B, a clone of A
* Clone C, a clone of B
If we promote C, it discards C's livelist. It should discard B's
livelist, but that is not happening. The impact is that when B is
destroyed, we use the livelist to find the blocks to free, but the
livelist is no longer correct so we end up freeing blocks that are still
in use by C. The incorrectly-freed blocks can be reallocated causing
checksum errors. And when C is destroyed it can double-free the
incorrectly-freed blocks.
The problem is that we remove the livelist of `origin_ds->ds_dir`, but
the origin snapshot has already been moved to the promoted dsl_dir. So
this is actually trying to remove the livelist of the promoted dsl_dir,
which was already removed. As explained in a comment in the beginning
of `dsl_dataset_promote_sync()`, we need to use the saved `odd` for the
origin's dsl_dir.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10652
* Fixed a typo that cause one of the variations to be a no-op
* Added additional coverage for adding special vdev after pool create
* Added additional coverage for using 4K sector size
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10641
The `zfs program` subcommand invokes a LUA interpreter to run ZFS
"channel programs". This interpreter runs in a constrained environment,
with defined memory limits. The LUA stack (used for LUA functions that
call each other) is allocated in the kernel's heap, and is limited by
the `-m MEMORY-LIMIT` flag and the `zfs_lua_max_memlimit` module
parameter. The C stack is used by certain LUA features that are
implemented in C. The C stack is limited by `LUAI_MAXCCALLS=20`, which
limits call depth.
Some LUA C calls use more stack space than others, and `gsub()` uses an
unusually large amount. With a programming trick, it can be invoked
recursively using the C stack (rather than the LUA stack). This
overflows the 16KB Linux kernel stack after about 11 iterations, less
than the limit of 20.
One solution would be to decrease `LUAI_MAXCCALLS`. This could be made
to work, but it has a few drawbacks:
1. The existing test suite does not pass with `LUAI_MAXCCALLS=10`.
2. There may be other LUA functions that use a lot of stack space, and
the stack space may change depending on compiler version and options.
This commit addresses the problem by adding a new limit on the amount of
free space (in bytes) remaining on the C stack while running the LUA
interpreter: `LUAI_MINCSTACK=4096`. If there is less than this amount
of stack space remaining, a LUA runtime error is generated.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10611Closes#10613
Adding a new subcommand to zstream called token. This
now allows users to decode a resume token to retrieve the toname
field. This can be useful for tools that need this information.
The syntax works as follows zstream token <resume_token>.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Tony Perkins <tperkins@datto.com>
Closes#10558
When libudev is installed on FreeBSD, configure finds it and sets
WANT_DEVNAME2DEVID, but it isn't found by the linker because we
didn't specify where it is.
Use LIBUDEV_LIBS so the location of the library gets added to the
linker flags for devname2devid.
Also use LIBUDEV_CFLAGS here in case some other platform needs it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10590
Stock kernels older than 4.10 do not export the has_capability()
function which is required by commit e59a377. To avoid breaking
the build on older kernels revert to the safe legacy behavior and
return EACCES when privileges cannot be checked.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10565Closes#10573
FreeBSD stat uses -f to specify the format string rather than -c.
list_file_blocks in blkdev.shlib uses stat -c %i to get a file's
object ID for zdb. We already have a library function to do this
portably.
Use get_objnum to get the file's object ID.
Take log_must off of the call to list_free_blocks in
corrupt_blocks_at_level, which had masked the error. It was not good
to pipe the output of log_must into the while-loop, anyway.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10572
Livelists and spacemaps are data structures that are logs of allocations
and frees. Livelists entries are block pointers (blkptr_t). Spacemaps
entries are ranges of numbers, most often used as to track
allocated/freed regions of metaslabs/vdevs.
These data structures can become self-inconsistent, for example if a
block or range can be "double allocated" (two allocation records without
an intervening free) or "double freed" (two free records without an
intervening allocation).
ZDB (as well as zfs running in the kernel) can detect these
inconsistencies when loading livelists and metaslab. However, it
generally halts processing when the error is detected.
When analyzing an on-disk problem, we often want to know the entire set
of inconsistencies, which is not possible with the current behavior.
This commit adds a new flag, `zdb -y`, which analyzes the livelist and
metaslab data structures and displays all of their inconsistencies.
Note that this is different from the leak detection performed by
`zdb -b`, which checks for inconsistencies between the spacemaps and the
tree of block pointers, but assumes the spacemaps are self-consistent.
The specific checks added are:
Verify livelists by iterating through each sublivelists and:
- report leftover FREEs
- report double ALLOCs and double FREEs
- record leftover ALLOCs together with their TXG [see Cross Check]
Verify spacemaps by iterating over each metaslab and:
- iterate over spacemap and then the metaslab's entries in the
spacemap log, then report any double FREEs and double ALLOCs
Verify that livelists are consistenet with spacemaps. The space
referenced by livelists (after using the FREE's to cancel out
corresponding ALLOCs) should be allocated, according to the spacemaps.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-66031
Closes#10515
A bunch of places need to edit files to incorporate the configured paths
i.e. bindir, sbindir etc. Move this logic into a common file.
Create arc_summary by copying arc_summary[23] as appropriate at build
time instead of install time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10559
== Motivation and Context
The current implementation of 'sharenfs' and 'sharesmb' relies on
the use of the sharetab file. The use of this file is os-specific
and not required by linux or freebsd. Currently the code must
maintain updates to this file which adds complexity and presents
a significant performance impact when sharing many datasets. In
addition, concurrently running 'zfs sharenfs' command results in
missing entries in the sharetab file leading to unexpected failures.
== Description
This change removes the sharetab logic from the linux and freebsd
implementation of 'sharenfs' and 'sharesmb'. It still preserves an
os-specific library which contains the logic required for sharing
NFS or SMB. The following entry points exist in the vastly simplified
libshare library:
- sa_enable_share -- shares a dataset but may not commit the change
- sa_disable_share -- unshares a dataset but may not commit the change
- sa_is_shared -- determine if a dataset is shared
- sa_commit_share -- notify NFS/SMB subsystem to commit the shares
- sa_validate_shareopts -- determine if sharing options are valid
The sa_commit_share entry point is provided as a performance enhancement
and is not required. The sa_enable_share/sa_disable_share may commit
the share as part of the implementation. Libshare provides a framework
for both NFS and SMB but some operating systems may not fully support
these protocols or all features of the protocol.
NFS Operation:
For linux, libshare updates /etc/exports.d/zfs.exports to add
and remove shares and then commits the changes by invoking
'exportfs -r'. This file, is automatically read by the kernel NFS
implementation which makes for better integration with the NFS systemd
service. For FreeBSD, libshare updates /etc/zfs/exports to add and
remove shares and then commits the changes by sending a SIGHUP to
mountd.
SMB Operation:
For linux, libshare adds and removes files in /var/lib/samba/usershares
by calling the 'net' command directly. There is no need to commit the
changes. FreeBSD does not support SMB.
== Performance Results
To test sharing performance we created a pool with an increasing number
of datasets and invoked various zfs actions that would enable and
disable sharing. The performance testing was limited to NFS sharing.
The following tests were performed on an 8 vCPU system with 128GB and
a pool comprised of 4 50GB SSDs:
Scale testing:
- Share all filesystems in parallel -- zfs sharenfs=on <dataset> &
- Unshare all filesystems in parallel -- zfs sharenfs=off <dataset> &
Functional testing:
- share each filesystem serially -- zfs share -a
- unshare each filesystem serially -- zfs unshare -a
- reset sharenfs property and unshare -- zfs inherit -r sharenfs <pool>
For 'zfs sharenfs=on' scale testing we saw an average reduction in time
of 89.43% and for 'zfs sharenfs=off' we saw an average reduction in time
of 83.36%.
Functional testing also shows a huge improvement:
- zfs share -- 97.97% reduction in time
- zfs unshare -- 96.47% reduction in time
- zfs inhert -r sharenfs -- 99.01% reduction in time
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Bryant G. Ly <bryangly@gmail.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-68690
Closes#1603Closes#7692Closes#7943Closes#10300
We already enable -DDEBUG unconditionally (meaning regardless
of this is a debug build or a performance build) for zdb and
ztest as they are mostly used for development and debugging.
This patch enables -DDEBUG for libzpool extending the debugging
checks for zdb, ztest, and a couple of other test utilities.
In addition to passing -DDEBUG we also enable -DZFS_DEBUG so
all assertion checks work s expected. We do so not only in
libzpool but in every utility that links to it, even if the
utility doesn't directly use any functionality wrapped in
ZFS_DEBUG macro definitions. The reason is that these utilities
may still include headers that contain structs that have more
fields when ZFS_DEBUG is defined. This can be a problem as
enabling that flag for libzpool but not for zdb can lead into
random problems (e.g. segmentation faults) as zdb may be have
an incorrect view of a struct passed to it by libzpool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#10549
libtool stores absolute paths in the dependency_libs component of the
.la files. If the Makefile for a dependent library refers to the
libraries by relative path, some libraries end up duplicated on the link
command line.
As an example, libzfs specifies libzfs_core, libnvpair and libuutil as
dependencies to be linked in. The .la file for libzfs_core also
specifies libnvpair, but using an absolute path, with the result that
libnvpair is present twice in the linker command line for producing
libzfs.
While the only thing this causes is to slightly slow down the linking,
we can avoid it by using absolute paths everywhere, including for
convenience libraries just for consistency.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
Commit e8864b1b28 ("config: libintl/libiconv for gettext() detection")
added an empty config.rpath with a comment that the real one doesn't
work with libtool.
However, an empty config.rpath doesn't really work: eg. on FreeBSD,
where libintl is in /usr/local/lib, configure thinks that gettext
doesn't exist and NLS should be disabled, which currently isn't
supported in the source, and hence requires manual workaround to
directly link -lintl without relying on configure. config.rpath is
essential to let it be detected either in --prefix or using
--with-libintl-prefix.
I also don't see the mentioned issue with libtool flags applied to
compilation, it seems to work fine to pass LTLIBINTL to libtool. It's
unnecessary to include LTLIBICONV as the configure test will
automatically append that to LTLIBINTL if it is necessary to link with
libiconv.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
libzutil is currently statically linked into libzfs, libzfs_core and
libzpool. Avoid the unnecessary duplication by removing it from libzfs
and libzpool, and adding libzfs_core to libzpool.
Remove a few unnecessary dependencies:
- libuutil from libzfs_core
- libtirpc from libspl
- keep only libcrypto in libzfs, as we don't use any functions from
libssl
- librt is only used for clock_gettime, however on modern systems that's
in libc rather than librt. Add a configure check to see if we actually
need librt
- libdl from raidz_test
Add a few missing dependencies:
- zlib to libefi and libzfs
- libuuid to zpool, and libuuid and libudev to zed
- libnvpair uses assertions, so add assert.c to provide aok and
libspl_assertf
Sort the LDADD for programs so that libraries that satisfy dependencies
come at the end rather than the beginning of the linker command line.
Revamp the configure tests for libaries to use FIND_SYSTEM_LIBRARY
instead. This can take advantage of pkg-config, and it also avoids
polluting LIBS.
List all the required dependencies in the pkgconfig files, and move the
one for libzfs_core into the latter's directory. Install pkgconfig files
in $(libdir)/pkgconfig on linux and $(prefix)/libdata/pkgconfig on
FreeBSD, instead of /usr/share/pkgconfig, as the more correct location
for library .pc files.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
Variadic functions cannot be inlined. libspl_assertf ends up being
duplicated in every file that uses it.
Fix this by moving the function into a new assert.c. Also move the
definition of aok into the new file instead of zone.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10538
FreeBSD recently replaced the GNU bc and dc in the base system with
BSD licensed versions. They are supposed to be compatible with all
the features present in the GNU versions, but it turns out they are
picky about `if` statements having a corresponding `else`. ZTS uses
`echo "if ($x > $y) 1" | bc` in a few places, which causes tests to
fail unexpectedly with the new bc.
Change the two expressions in ZTS to `if ($x > $y) 1 else 0` for
compatibility with the new BSD bc.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10551
The device_rebuild feature enables sequential reconstruction when
resilvering. Mirror vdevs can be rebuilt in LBA order which may
more quickly restore redundancy depending on the pools average block
size, overall fragmentation and the performance characteristics
of the devices. However, block checksums cannot be verified
as part of the rebuild thus a scrub is automatically started after
the sequential resilver completes.
The new '-s' option has been added to the `zpool attach` and
`zpool replace` command to request sequential reconstruction
instead of healing reconstruction when resilvering.
zpool attach -s <pool> <existing vdev> <new vdev>
zpool replace -s <pool> <old vdev> <new vdev>
The `zpool status` output has been updated to report the progress
of sequential resilvering in the same way as healing resilvering.
The one notable difference is that multiple sequential resilvers
may be in progress as long as they're operating on different
top-level vdevs.
The `zpool wait -t resilver` command was extended to wait on
sequential resilvers. From this perspective they are no different
than healing resilvers.
Sequential resilvers cannot be supported for RAIDZ, but are
compatible with the dRAID feature being developed.
As part of this change the resilver_restart_* tests were moved
in to the functional/replacement directory. Additionally, the
replacement tests were renamed and extended to verify both
resilvering and rebuilding.
Original-patch-by: Isaac Huang <he.huang@intel.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: John Poduska <jpoduska@datto.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10349
The block histogram tracks the changes to psize, lsize and asize
both in the count of the number of blocks (by blocksize) and the
total length of all of the blocks for that blocksize. It also
keeps a running total of the cumulative size of all of the blocks
up to each size to help determine the size of caching SSDs to be
added to zfs hardware deployments.
The block history counts and lengths are summarized in bins
which are powers of two. Even rows with counts of zero are printed.
This change is accessed by specifying one of two options:
zdb -bbb pool
zdb -Pbbb pool
The first version prints the table in fixed size columns.
The second prints in "parseable" output that can be placed into
a CSV file.
Fixed Column, nicenum output sample:
block psize lsize asize
size Count Length Cum. Count Length Cum. Count Length Cum.
512: 3.50K 1.75M 1.75M 3.43K 1.71M 1.71M 3.41K 1.71M 1.71M
1K: 3.65K 3.67M 5.43M 3.43K 3.44M 5.15M 3.50K 3.51M 5.22M
2K: 3.45K 6.92M 12.3M 3.41K 6.83M 12.0M 3.59K 7.26M 12.5M
4K: 3.44K 13.8M 26.1M 3.43K 13.7M 25.7M 3.49K 14.1M 26.6M
8K: 3.42K 27.3M 53.5M 3.41K 27.3M 53.0M 3.44K 27.6M 54.2M
16K: 3.43K 54.9M 108M 3.50K 56.1M 109M 3.42K 54.7M 109M
32K: 3.44K 110M 219M 3.41K 109M 218M 3.43K 110M 219M
64K: 3.41K 218M 437M 3.41K 218M 437M 3.44K 221M 439M
128K: 3.41K 437M 874M 3.70K 474M 911M 3.41K 437M 876M
256K: 3.41K 874M 1.71G 3.41K 874M 1.74G 3.41K 874M 1.71G
512K: 3.41K 1.71G 3.41G 3.41K 1.71G 3.45G 3.41K 1.71G 3.42G
1M: 3.41K 3.41G 6.82G 3.41K 3.41G 6.86G 3.41K 3.41G 6.83G
2M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
4M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
8M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
16M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Robert E. Novak <novak5@llnl.gov>
Closes: #9158Closes#10315
Reduce the usage of EXTRA_DIST. If files are conditionally included in
_SOURCES, _HEADERS etc, automake is smart enough to dist all files that
could possibly be included, but this does not apply to EXTRA_DIST,
resulting in make dist depending on the configuration.
Add some files that were missing altogether in various Makefile's.
The changes to disted files in this commit (excluding deleted files):
+./cmd/zed/agents/README.md
+./etc/init.d/README.md
+./lib/libspl/os/freebsd/getexecname.c
+./lib/libspl/os/freebsd/gethostid.c
+./lib/libspl/os/freebsd/getmntany.c
+./lib/libspl/os/freebsd/mnttab.c
-./lib/libzfs/libzfs_core.pc
-./lib/libzfs/libzfs.pc
+./lib/libzfs/os/freebsd/libzfs_compat.c
+./lib/libzfs/os/freebsd/libzfs_fsshare.c
+./lib/libzfs/os/freebsd/libzfs_ioctl_compat.c
+./lib/libzfs/os/freebsd/libzfs_zmount.c
+./lib/libzutil/os/freebsd/zutil_compat.c
+./lib/libzutil/os/freebsd/zutil_device_path_os.c
+./lib/libzutil/os/freebsd/zutil_import_os.c
+./module/lua/README.zfs
+./module/os/linux/spl/README.md
+./tests/README.md
+./tests/zfs-tests/tests/functional/cli_root/zfs_clone/zfs_clone_rm_nested.ksh
+./tests/zfs-tests/tests/functional/cli_root/zfs_send/zfs_send_encrypted_unloaded.ksh
+./tests/zfs-tests/tests/functional/inheritance/README.config
+./tests/zfs-tests/tests/functional/inheritance/README.state
+./tests/zfs-tests/tests/functional/rsend/rsend_016_neg.ksh
+./tests/zfs-tests/tests/perf/fio/sequential_readwrite.fio
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10501
Implements a pam module for automatically loading zfs encryption keys
for home datasets. The pam module:
- loads a zfs key and mounts the dataset when a session opens.
- unmounts the dataset and unloads the key when the session closes.
- when the user is logged on and changes the password, the module
changes the encryption key.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: @jengelh <jengelh@inai.de>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
Closes#9886Closes#9903
This tunable required a handler to be implemented for
ZFS_MODULE_PARAM_CALL.
Add the handler so the tunable can be declared in common code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10490
Rephrase comments to be more clear.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10481
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Implement semi-compatible functionality for mode=0 (preallocation)
and mode=FALLOC_FL_KEEP_SIZE (preallocation beyond EOF) for ZPL.
Since ZFS does COW and snapshots, preallocating blocks for a file
cannot guarantee that writes to the file will not run out of space.
Even if the first overwrite was guaranteed, it would not handle any
later overwrite of blocks due to COW, so strict compliance is futile.
Instead, make a best-effort check that at least enough free space is
currently available in the pool (with a bit of margin), then create
a sparse file of the requested size and continue on with life.
This does not handle all cases (e.g. several fallocate() calls before
writing into the files when the filesystem is nearly full), which
would require a more complex mechanism to be implemented, probably
based on a modified version of dmu_prealloc(), but is usable as-is.
A new module option zfs_fallocate_reserve_percent is used to control
the reserve margin for any single fallocate call. By default, this
is 110% of the requested preallocation size, so an additional 10% of
available space is reserved for overhead to allow the application a
good chance of finishing the write when the fallocate() succeeds.
If the heuristics of this basic fallocate implementation are not
desirable, the old non-functional behavior of returning EOPNOTSUPP
for calls can be restored by setting zfs_fallocate_reserve_percent=0.
The parameter of zfs_statvfs() is changed to take an inode instead
of a dentry, since no dentry is available in zfs_fallocate_common().
A few tests from @behlendorf cover basic fallocate functionality.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Arshad Hussain <arshad.super@gmail.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Issue #326Closes#10408
The horrible effects of human slavery continue to impact society. The
casual use of the term "slave" in computer software is an unnecessary
reference to a painful human experience.
This commit removes all possible references to the term "slave".
Implementation notes:
The zpool.d/slaves script is renamed to dm-deps, which uses the same
terminology as `dmsetup deps`.
References to the `/sys/class/block/$dev/slaves` directory remain. This
directory name is determined by the Linux kernel. Although
`dmsetup deps` provides the same information, it unfortunately requires
elevated privileges, whereas the `/sys/...` directory is world-readable.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10435
Correct various typos in the comments and tests.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#10423
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
Use option '-o' after action for compatibility
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#10426
The l2arc_evict() function is responsible for evicting buffers which
reference the next bytes of the L2ARC device to be overwritten. Teach
this function to additionally TRIM that vdev space before it is
overwritten if the device has been filled with data. This is done by
vdev_trim_simple() which trims by issuing a new type of TRIM,
TRIM_TYPE_SIMPLE.
We also implement a "Trim Ahead" feature. It is a zfs module parameter,
expressed in % of the current write size. This trims ahead of the
current write size. A minimum of 64MB will be trimmed. The default is 0
which disables TRIM on L2ARC as it can put significant stress to
underlying storage devices. To enable TRIM on L2ARC we set
l2arc_trim_ahead > 0.
We also implement TRIM of the whole cache device upon addition to a
pool, pool creation or when the header of the device is invalid upon
importing a pool or onlining a cache device. This is dependent on
l2arc_trim_ahead > 0. TRIM of the whole device is done with
TRIM_TYPE_MANUAL so that its status can be monitored by zpool status -t.
We save the TRIM state for the whole device and the time of completion
on-disk in the header, and restore these upon L2ARC rebuild so that
zpool status -t can correctly report them. Whole device TRIM is done
asynchronously so that the user can export of the pool or remove the
cache device while it is trimming (ie if it is too slow).
We do not TRIM the whole device if persistent L2ARC has been disabled by
l2arc_rebuild_enabled = 0 because we may not want to lose all cached
buffers (eg we may want to import the pool with
l2arc_rebuild_enabled = 0 only once because of memory pressure). If
persistent L2ARC has been disabled by setting the module parameter
l2arc_rebuild_blocks_min_l2size to a value greater than the size of the
cache device then the whole device is trimmed upon creation or import of
a pool if l2arc_trim_ahead > 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam D. Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9713Closes#9789Closes#10224
Without these headers, compilation fails on musl libc with offset_t
being undeclared and MIN being implictly declared.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Hiếu Lê <leorize+oss@disroot.org>
Closes#10406
It can take a moment for the NFS server to give up the mountpoint
after unsharing a filesystem.
Use log_must_busy to retry export/destroy a few times after switching
off sharenfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10380
Update cleanup_filesystem to use destroy_dataset when performing
cleanup. This ensures the destroy is retried if the pool is busy
preventing occasional failures.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10358
Allow zfs datasets to be mounted on Linux without relying on the
invocation of an external processes. This is the same behavior
which is implemented for FreeBSD.
Use of the libmount library was originally considered because it
provides functionality to properly lock and update the /etc/mtab
file. However, these days /etc/mtab is typically a symlink to
/proc/self/mounts so there's nothing to updated. Therefore, we
call mount(2) directly and avoid any additional dependencies.
If required the legacy behavior can be enabled by setting the
ZFS_MOUNT_HELPER environment variable. This may be needed in
environments where SELinux in enabled and the zfs binary does
not have mount permission.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Dörre <felix@dogcraft.de>
#10294
Small program that converts a dataset id and an object id to a path
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10204
The cleanup routine for this test attempts to remove some temporary
files with `rm -f $VDEV_*`, but VDEV_ is undefined. As a result, all
files in the current working directory (/var/tmp/test_results/current)
get removed instead. This includes the complete log file of all tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#10324
When a resilver finishes, vdev_dtl_reassess is called to hopefully
excise DTL_MISSING (amongst other things). If there are errors during
the resilver, they are tracked in DTL_SCRUB, as spelled out in the
block comment in vdev.c. DTL_SCRUB is in-core only, so it can only
be used if the pool was online for the whole resilver. This state is
tracked with the spa_scrub_started flag, which only gets set when
the scan is initialized. Unfortunately, this flag gets cleared right
before vdev_dtl_reassess gets called, so if there are any errors
during the scan, DTL_MISSING will never get excised and the resilver
will just continually restart. This fix simply moves clearing that
flag until after the call to vdev_dtl_reasses.
In addition, if a pool is imported and already has scn_errors > 0,
this change will restart the resilver immediately instead of doing
the rest of the scan and then restarting it from the beginning. On
the other hand, if scn_errors == 0 at import, then no errors have
been encountered so far, so the spa_scrub_started flag can be safely
set.
A test has been added to verify that resilver does not restart when
relevant DTL's are available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10291
When building on native dev system, there are no issues but when
cross-compiling for target system, some linker errors are observed.
The only way to avoid these errors is by adjusting the Makefile.am
of those various components to add the library dependencies.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Petros Koutoupis <petros@petroskoutoupis.com>
Closes#10304
When recursively destroying the dataset it's possible for the
dataset volume to be open by an unrelated process, like blkid.
Use the destroy_dataset() which will retry when this occurs.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10305
Functional changes:
We implement refcounts of log blocks and their aligned size on the
cache device along with two corresponding arcstats. The refcounts are
reflected in the header of the device and provide valuable information
as to whether log blocks are accounted for correctly. These are
dynamically adjusted as log blocks are committed/evicted. zdb also uses
this information in the device header and compares it to the
corresponding values as reported by dump_l2arc_log_blocks() which
emulates l2arc_rebuild(). If the refcounts saved in the device header
report higher values, zdb exits with an error. For this feature to work
correctly there should be no active writes on the device. This is also
employed in the tests of persistent L2ARC. We extend the structure of
the cache device header by adding the two new variables mirroring the
refcounts after the existing variables to preserve backward
compatibility in terms of persistent L2ARC.
1) a new arcstat "l2_log_blk_asize" and refcount "l2ad_lb_asize" which
reflect the total aligned size of log blocks on the device. This is
also reflected in the header of the cache device as "dh_lb_asize".
2) a new arcstat "l2arc_log_blk_count" and refcount "l2ad_lb_count"
which reflect the total number of L2ARC log blocks present on cache
devices. It is also reflected in the header of the cache device as
"dh_lb_count".
In l2arc_rebuild_vdev() if the amount of committed log entries in a log
block is 0 and the device header is valid we update the device header.
This will facilitate trimming of the whole device in this case when
TRIM for L2ARC is implemented.
Improve loop protection in l2arc_rebuild() by using the starting offset
of the payload of each log block instead of the starting offset of the
log block.
If the zio in l2arc_write_buffers() fails, restore the lbps array in the
header of the device to its previous state in l2arc_write_done().
If l2arc_rebuild() ends the rebuild process without restoring any L2ARC
log blocks in ARC and without any other error, this means that the lbps
array in the header is pointing to non-existent or invalid log blocks.
Reset the device header in this case.
In l2arc_rebuild() change the zfs_dbgmsg messages to
spa_history_log_internal() making them user visible with zpool history
command.
Non-functional changes:
Make the first test in persistent L2ARC use `zdb -lll` to increase
coverage in `zdb.c`.
Rename psize with asize when referring to log blocks, since
L2ARC_SET_PSIZE stores the vdev aligned size for log blocks. Also
rename dh_log_blk_entries to dh_log_entries to make it clear that
it is a mirror of l2ad_log_entries. Added comments for both changes.
Fix inaccurate comments for example in l2arc_log_blk_restore().
Add asserts at the end in l2arc_evict() and l2arc_write_buffers().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10228
Modern bootloaders leverage data stored in the root filesystem to
enable some of their powerful features. GRUB specifically has a grubenv
file which can store large amounts of configuration data that can be
read and written at boot time and during normal operation. This allows
sysadmins to configure useful features like automated failover after
failed boot attempts. Unfortunately, due to the Copy-on-Write nature
of ZFS, the standard behavior of these tools cannot handle writing to
ZFS files safely at boot time. We need an alternative way to store
data that allows the bootloader to make changes to the data.
This work is very similar to work that was done on Illumos to enable
similar functionality in the FreeBSD bootloader. This patch is different
in that the data being stored is a raw grubenv file; this file can store
arbitrary variables and values, and the scripting provided by grub is
powerful enough that special structures are not required to implement
advanced behavior.
We repurpose the second padding area in each label to store the grubenv
file, protected by an embedded checksum. We add two ioctls to get and
set this data, and libzfs_core and libzfs functions to access them more
easily. There are no direct command line interfaces to these functions;
these will be added directly to the bootloader utilities.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10009
When a top-level vdev is removed from a pool it is converted to an
indirect vdev. Until now splitting such mirrored pools was not possible
with zpool split. This patch enables handling of indirect vdevs and
splitting of those pools with zpool split.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10283
The verify_pool function should detect checksum errors on any vdev, but
it was only checking at the root of the pool.
Accumulate the errors for all vdevs to obtain the correct count.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10271
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
Closes#10243
Round up the volume size requested in `zfs create -V size` to the next
higher multiple of the volblocksize. Updates the man page and adds a
test to verify the new behavior.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: puffi <puffi@users.noreply.github.com>
Signed-off-by: Alex John <alex@stty.io>
Closes#8541Closes#10196
Deduplicated send streams (i.e. `zfs send -D` and `zfs receive` of such
streams) are deprecated. Deduplicated send streams can be received by
first converting them to non-deduplicated with the `zstream redup`
command.
This commit removes the code for sending and receiving deduplicated send
streams. `zfs send -D` will now print a warning, ignore the `-D` flag,
and generate a regular (non-deduplicated) send stream. `zfs receive` of
a deduplicated send stream will print an error message and fail.
The resulting code simplification (especially in the kernel's support
for receiving dedup streams) should help enable future performance
enhancements.
Several new tests are added which leverage `zstream redup`.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #7887
Issue #10117
Issue #10156Closes#10212
Minor fixes on persistent L2ARC improving code readability and fixing
a typo in zdb.c when byte-swapping a log block. It also improves the
pesist_l2arc_007_pos.ksh test by giving it more time to retrieve log
blocks on the cache device.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam D. Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10210
Remove some obsolete legacy compat, rename some misnamed, and add some
missing tunables for FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10203
Add the FreeBSD platform code to the OpenZFS repository. As of this
commit the source can be compiled and tested on FreeBSD 11 and 12.
Subsequent commits are now required to compile on FreeBSD and Linux.
Additionally, they must pass the ZFS Test Suite on FreeBSD which is
being run by the CI. As of this commit 1230 tests pass on FreeBSD
and there are no unexpected failures.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#898Closes#8987
Commit 379ca9c removed the requirement on aux devices to be block
devices only but the test case cache_010_neg was not updated, making it
fail consistently.
This change changes the test to check that cache devices _can_ be
anything that presents a block interface. The testcase is renamed to
cache_010_pos and the exceptions for known failure removed from the test
runner.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alex John <alex@stty.io>
Closes#10172
Deduplicated send and receive is deprecated. To ease migration to the
new dedup-send-less world, the commit adds a `zstream redup` utility to
convert deduplicated send streams to normal streams, so that they can
continue to be received indefinitely.
The new `zstream` command also replaces the functionality of
`zstreamdump`, by way of the `zstream dump` subcommand. The
`zstreamdump` command is replaced by a shell script which invokes
`zstream dump`.
The way that `zstream redup` works under the hood is that as we read the
send stream, we build up a hash table which maps from `<GUID, object,
offset> -> <file_offset>`.
Whenever we see a WRITE record, we add a new entry to the hash table,
which indicates where in the stream file to find the WRITE record for
this block. (The key is `drr_toguid, drr_object, drr_offset`.)
For entries other than WRITE_BYREF, we pass them through unchanged
(except for the running checksum, which is recalculated).
For WRITE_BYREF records, we change them to WRITE records. We find the
referenced WRITE record by looking in the hash table (for the record
with key `drr_refguid, drr_refobject, drr_refoffset`), and then reading
the record header and payload from the specified offset in the stream
file. This is why the stream can not be a pipe. The found WRITE record
replaces the WRITE_BYREF record, with its `drr_toguid`, `drr_object`,
and `drr_offset` fields changed to be the same as the WRITE_BYREF's
(i.e. we are writing the same logical block, but with the data supplied
by the previous WRITE record).
This algorithm requires memory proportional to the number of WRITE
records (same as `zfs send -D`), but the size per WRITE record is
relatively low (40 bytes, vs. 72 for `zfs send -D`). A 1TB send stream
with 8KB blocks (`recordsize=8k`) would use around 5GB of RAM to
"redup".
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10124Closes#10156
This commit makes the L2ARC persistent across reboots. We implement
a light-weight persistent L2ARC metadata structure that allows L2ARC
contents to be recovered after a reboot. This significantly eases the
impact a reboot has on read performance on systems with large caches.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Saso Kiselkov <skiselkov@gmail.com>
Co-authored-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Ported-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#925Closes#1823Closes#2672Closes#3744Closes#9582
The delegate tests use `date(1)` to generate snapshot names, using
the format '%F-%T-%N' to get nanosecond resolution (since multiple
snapshots may be taken in the same second). '%N' is not portable, and
causes tests to fail on FreeBSD.
Since the only purpose these timestamps serve is to create a unique
name, simply use $RANDOM instead.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10170
Add a mechanism to wait for delete queue to drain.
When doing redacted send/recv, many workflows involve deleting files
that contain sensitive data. Because of the way zfs handles file
deletions, snapshots taken quickly after a rm operation can sometimes
still contain the file in question, especially if the file is very
large. This can result in issues for redacted send/recv users who
expect the deleted files to be redacted in the send streams, and not
appear in their clones.
This change duplicates much of the zpool wait related logic into a
zfs wait command, which can be used to wait until the internal
deleteq has been drained. Additional wait activities may be added
in the future.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9707
Increasing l2arc_write_size or l2arc_write_boost can result in
l2arc_write_buffers() not having enough space to perform its writes and
panic zio_write_phys().
Instead of resetting l2ad_hand to l2ad_start at the end of
l2arc_write_buffers() and not taking into account a possible
user-mediated increase of l2arc_write_max, we do this in l2arc_evict(),
right after l2arc_write_size() has run. If there is not enough space to
evict (ie we will exceed l2ad_end) we evict to the end of the device,
reset l2ad_hand to l2ad_start, set l2ad_first to 0 and iterate
l2arc_evict(). We avoid infinite iteration of l2arc_evict() by making
sure in l2arc_write_size() that l2ad_start + size does not exceed
l2ad_end.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10154
udev is only used on Linux.
Skip udev_wait and udev_cleanup when not on Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10165
And in removal tests, sync the specific pool we are waiting on.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10146
libzfs aborts and dumps core on EINVAL from the kernel when trying to
do a redacted send with a bookmark that is not a redaction bookmark.
Move redacted bookmark validation into libzfs.
Check if the bookmark given for redactions is actually a redaction
bookmark. Print an error message and exit gracefully if it is not.
Don't abort on EINVAL in zfs_send_one.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10138
Fix minor cstyle warnings accidentally introduced by 7145123b.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10143
This change adds a separate return code to zfs_ioc_recv that is used
for incomplete streams, in addition to the existing return code for
streams that contain corruption.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10122
Currently when the dataset is in use we can't receive snapshots.
zfs send test/1@asd | zfs recv -FM test/2
cannot unmount '/test/2': Device busy
This commits add option 'M' which attempts to forcibly unmount the
dataset. Thanks to this we can enforce receiving snapshots in a
single step.
Note that this functionality is not supported on Linux because the
VFS will prevent active mounted filesystems from being unmounted,
even with the force option. This is the intended VFS behavior.
Test cases were added to verify the expected behavior based on
the platform.
Discussed-with: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
External-issue: https://reviews.freebsd.org/D22306Closes#9904
And add log_pass appropriately.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10136
Issue #9142 describes an error in the checks for device removal that
can prevent removal of special allocation class vdevs in some
situations.
Enhance alloc_class/alloc_class_012_pos to check situations where this
bug occurs.
Update zts-report with knowledge of issue #9142.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10116
Issue #9142
Cleanup for write_dirs involves destroying a dataset filling a pool
and then recreating the dataset for the next test. Due to the
asynchronous nature of free space accounting, recreating the dataset
can fail for lack of space, causing problems for the next test.
Add wait_freeing $TESTPOOL to wait for the space to be freed and then
sync_pool $TESTPOOL to update the space accounting before attempting
to recreate the test filesystem.
Only use a single disk to create the pool. Make it a small file so it
does not take too long to fill.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10112
Tests that get killed do not have an opportunity to clean up.
There are many bad states this can leave the system in, but of
particular gravity is when zinject has been used to induce bad
behavior for one or more of the test disks.
Create a failsafe mechanism in test-runner.py that runs a callback
script after every test. The script is common to all tests so all
tests benefit from the protection.
Add an obligatory `zinject -c all` to clear all zinject state after
every test case is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10096
Don't echo the results of arithmetic expressions, it's not necessary.
Use hw.clockrate sysctl to get CPU freq instead of parsing dmesg.boot
for a line that might not even be there anymore.
Reduce bookkeeping in fill_fs, making it easier to follow.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10113
Filesystems allow overlay mounts by default on FreeBSD and Linux.
Respect the native convention by switching the default to overlay=on,
while retaining the option to turn the property off for compatibility
with other operating systems' conventions.
Update documentation and tests accordingly.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10030
The write_dirs tests fill a filesystem with a bunch of files until it
is full. In cleanup the files are truncated and removed individually.
These tests already take a while to run.
It is quicker and easier to destroy the whole dataset and create a new
one to replace it in the cleanup functions.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10098
`default_setup` takes a disk list as the first argument and has
optional additional arguments that control secondary functionality.
A couple of test setups mistakenly call `default_setup $DISKS`.
Add quotes so the second and subsequent disks are correctly included
in the pool as vdevs rather than triggering unwanted behavior from
`default_setup`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10097
There are three tests we expect to fail only on FreeBSD.
* link_count never exits and eventually times out:
- @amotin tells me this test is probably not applicable to us
- Skip on FreeBSD
* userobj feature does not activate immediately after pool upgrade
- low impact; we are aware of this issue
* removal does not appear to condense on export
- low impact; we are aware of this issue
Additionally removal_with_zdb passes on FreeBSD, so it is moved to
"maybe".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10093
See issue #8226: Property filesystem_limit does not work as documented
There have been previous attempts to fix the behavior on Linux, but so
far the issue is still open. See PRs #8228, #8280.
The existing tests pass for the incorrect behavior. This is a problem
on FreeBSD; we are failing the tests because we implement the feature
correctly.
I have adapted the tests based on the work by @loli10k in #8280 and
extended the changes to fix the snapshot_limit test as well.
Linux now fails these tests, so entries linking to the issue have been
added to the "maybe" group in zts-report.py.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10082
Manual trims fall into the category of long-running pool activities
which people might want to wait synchronously for. This change adds
support to 'zpool wait' for waiting for manual trim operations to
complete. It also adds a '-w' flag to 'zpool trim' which can be used to
turn 'zpool trim' into a synchronous operation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10071
Shared test library functions lack a simple way to ensure proper
cleanup in the event of a failure. The `log_onexit` cleanup pattern
cannot be used in library functions because it uses one global
variable to store the cleanup command.
An example of where this is a serious issue is when a tunable that
artifically stalls kernel progress gets activated and then some check
fails. Unless the caller knows about the tunable and sets it back,
the system will be left in a bad state.
To solve this problem, turn the global cleanup variable into a stack.
Provide push and pop functions to add additional cleanup steps and
remove them after it is safe again.
The first use of this new functionality is in attempt_during_removal,
which sets REMOVAL_SUSPEND_PROGRESS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10080
This function should only return "linux" on Linux.
Move the kernel part of the function out of common code.
Fix the tests for FreeBSD.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10079
All other ksh scripts use /bin/ksh in the shebang.
Make rsend_016_neg consistent with the rest of the suite.
The test also was absent from any runfiles. Add it to common.run.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10051
Use file vdevs if we are short on $DISKS.
Also fixed vol recursion for FreeBSD in 004.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10060
* Set geom debug flags in corrupt_blocks_at_level
* Use the right time zone for history tests
* Add missing commands.cfg entry for diskinfo
* Rewrite get_last_txg_synced to use zdb
* Don't check ulimits for sparse files
* Suspend removal before removing a vdev, not after
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10054
`zfs recv` of an incremental stream that already exists is ignored, with
a message like:
receiving incremental stream of pool/fs@incsnap into pool/fs@incsnap
snap testpool/testfs@incsnap already exists; ignoring
And the command exits successfully (exit code 0).
The zfs_receive_004_neg test is expecting that a this case will fail,
with nonzero exit code.
The fix is to remove this specific command from the test case. This
lets us check that the remaining commands do in fact fail.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10055
The function `get_used_prop` does not exist.
Use `get_prop used` instead.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10059
Several casenorm tests pass on FreeBSD but are expected to fail on
Linux.
Move the passing tests from "fail" to "maybe" so that passing on
FreeBSD is not unexpected.
Invert platform logic so FreeBSD doesn't use illumos-only zlook.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10050
* Check for mountd in is_shared to avoid timeout when not running
* Enhance robustness of some cleanup functions
* Simplify atime lookup
* Skip sharenfs validation for now
* Don't add mountpoint property to inheritance validation on FreeBSD
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10047
zed_start may be called in places where zed is not
typically already running, but this is not a requirement
of the tests.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#9974
* Force UFS sync before snap in vol rollback tests
* rw is not a valid share option on FreeBSD, use ro instead
* zfs_unmount_nested: mountpoint is in the pool, rmdir *before* export
* Fix some more platform checks
* Fix disappearing group in delegate tests
* Don't try delegating for jailed, only root can set it
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10038
The zpool destroy tests partition a single disk to create two pools.
This can be done using two disks and no partitioning instead.
And temporarily allow vol recursion for FreeBSD while in here.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10036
FreeBSD doesn't have a `share` command. It does have showmount.
Split the separate platform impls out of is_shared_impl.
Dispatch to the correct platform impl function from is_shared.
Eliminate the use of is_shared_impl from tests. is_shared works.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10037
These tests are unspported on FreeBSD and Linux for lack of pfexec.
Move the privilege tests to sunos.run and remove the platform checks.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10035
These tests use lsblk to find the sector size of a disk.
FreeBSD doesn't have lsblk.
Use diskinfo -v to get sector size on FreeBSD.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>\
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10033
FreeBSD uses `pw` for account management. `userquota_006_pos`
erroneously invokes the non-existent `groupdel` command on FreeBSD.
Use `pw groupdel -n` instead of `groupdel` on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10032
FreeBSD does not support the "devices" and "nodevices" mount options.
Do not check these options on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10028
This test is supposed to verify zil operations. For TX_WRITE, writes
must be synchronous in order to be entered in the zil. Linux seems to
be doing sync writes even when they are not asked for, but on FreeBSD
the test does not do what is intended.
Use dd oflag=sync for the parts of this test that are supposed to
result in TX_WRITE zil entries.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10022
These tests can be made to work without a bunch of complex
partitioning of physical disks.
Use the 3 disks directly, creating a few file disks if needed for a
compelling reason.
Reduce the use of shared variables that don't have a clear utility.
Catch the fallout in tests that include cfg/shlib from zpool_create.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10002
For some unknown reason, egrep was misbehaving with this pattern on
FreeBSD. The command works fine run interactively from a shell, but
in the test the output of egrep is empty.
Work around the issue by using a filter in the awk script instead.
While here, add a bit of diagnostic output and other simplifications
to the awk script as well.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10023
FreeBSD doesn't have the -n flag for cmp.
Read the area for the first four labels from the disk to a separate
file to compare instead of using the special flag to limit the size.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10024
FreeBSD does not have the free command. This command is only used by
Linux in a perf hostinfo function.
Move free from the list of common commands to the list of Linux
commands.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10011
We have have made the necessary changes in our module code to expose
zevents through both devd and the zpool events ioctl. Now the tunables
can be exposed and zpool events tests can be enabled on both platforms.
A few minor tweaks to the tests were needed to accommodate the way wc
formats output on FreeBSD.
zed remains to be ported.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10008
Moving forward, we wish to use org.openzfs (no dash) rather than
org.open-zfs or org.zfsonlinux for feature GUIDs and property names.
The existing feature GUIDs cannot be changed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#10003
The cksum command is used by delegate tests. We have it on FreeBSD,
so it should not have been moved to the Linux commands list.
Move it back to the common commands list.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10007
This adds support for setting user properties in a
zfs channel program by adding 'zfs.sync.set_prop'
and 'zfs.check.set_prop' to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Contributions-by: Jason King <jason.king@joyent.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9950
Add missing logic for FreeBSD to a few test scripts.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9994
The zpool_add tests include zpool_create.shlib for a few silly
variables.
Don't use those variables for the file names. Include zpool_add.kshlib
for whatever variables we still need.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9997
These tests do not need to use partitions.
Get rid of the partitioning and just use the disks directly.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9996
These tests do not need to use partitions.
Get rid of the partitioning and just use the disks directly.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9995
Cleanup functions should make a best effort to clean up as much as
possible.
Do a consistency pass in a bunch of tests to make the cleanup
functions less prone to failure and fix a few typos here and there.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9993
Linux defines ECKSUM as EBADE, FreeBSD defines it as EINTEGRITY.
Test for ECKSUM instead of EBADE so we don't have to define EBADE for
this test on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9992
This was missed in review. On FreeBSD, script does not understand
environment variables being passed as a command.
Use env to make faketty handle env vars on FreeBSD.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9981
Missed this in the review, but wc output on FreeBSD is indented,
so string comparisons mismatch when comparing to an unindented number.
Compare counts as integers instead of strings.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9980
Add support for bookmark creation and cloning.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
This feature allows copying existing bookmarks using
zfs bookmark fs#target fs#newbookmark
There are some niche use cases for such functionality,
e.g. when using bookmarks as markers for replication progress.
Copying redaction bookmarks produces a normal bookmark that
cannot be used for redacted send (we are not duplicating
the redaction object).
ZCP support for bookmarking (both creation and copying) will be
implemented in a separate patch based on this work.
Overview:
- Terminology:
- source = existing snapshot or bookmark
- new/bmark = new bookmark
- Implement bookmark copying in `dsl_bookmark.c`
- create new bookmark node
- copy source's `zbn_phys` to new's `zbn_phys`
- zero-out redaction object id in copy
- Extend existing bookmark ioctl nvlist schema to accept
bookmarks as sources
- => `dsl_bookmark_create_nvl_validate` is authoritative
- use `dsl_dataset_is_before` check for both snapshot
and bookmark sources
- Adjust CLI
- refactor shortname expansion logic in `zfs_do_bookmark`
- Update man pages
- warn about redaction bookmark handling
- Add test cases
- CLI
- pyyzfs libzfs_core bindings
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
zdb -R :b fails due to the indirect block being compressed,
and the 'b' and 'd' flag not working in tandem when specified.
Fix the flag parsing code and create a zfs test for zdb -R
block display. Also fix the zio flags where the dotted notation
for the vdev portion of DVA (i.e. 0.0:offset:length) fails.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9640Closes#9729
Not all systems / distros have a `/bin/bash`, and these scripts are
more difficult to run at development time.
For example, my system is NixOS which doesn't have a /bin/bash. This
is not a problem for NixOS building ZFS as a package: the build
environment automatically replaces these shebangs with corrected
paths.
The problem is much more annoying at development time: either the
scripts don't run, or I correct them for my local machine and deal with
a perpetually dirty work tree.
Before committing this patch I confirmed there are existing scripts
which use `/usr/bin/env` to locate bash, so I am thinking this is a
safe transformation.
There are a handful of other shebangs in this repository which don't
work on my system. This patch is useful on its own specifically for
`commitcheck.sh`, otherwise I can't validate my commits before
submission.
Here are the remaining shebangs which NixOS systems won't have:
1274 #!/bin/ksh -p
91 #!/bin/ksh
89 #! /bin/ksh -p
2 #!/bin/sed -f
1 #!/usr/bin/perl -w
1 #!/usr/bin/ksh
1 #!/bin/nawk -f
plus this which will create an invalid shebang in
`tests/zfs-tests/tests/functional/mv_files/mv_files_common.kshlib`:
echo "#!/bin/ksh" > $TEST_BASE_DIR/exitsZero.ksh
I chose to leave those alone for now, and gauge the interest in this
much smaller patch first.
The fixes for these are easy enough by simply using `/usr/bin/env ksh`:
91 #!/bin/ksh
1 #!/usr/bin/ksh
The fix for the other set is much trickier. Quoting the GNU coreutils
manual:
Most operating systems (e.g. GNU/Linux, BSDs) treat all text after
the first space as a single argument. When using env in a script it
is thus not possible to specify multiple arguments.
and not all `env`'s support arguments.
Mine (GNU Coreutils 8.31) does, though this feature is new since
April 2018, GNU Coreutils 8.30:
https://git.savannah.gnu.org/cgit/coreutils.git/commit/?id=668306ed86c8c79b0af0db8b9c882654ebb66db2
and worse, requires the -S argument:
-S, --split-string=S process and split S into separate arguments;
used to pass multiple arguments on shebang
lines
Example:
$ seq 1 2 | $(nix-build '<nixpkgs>' -A coreutils)/bin/env "sort -nr"
/nix/[...]-coreutils-8.31/bin/env: ‘sort -nr’: No such file or directory
/nix/[...]-coreutils-8.31/bin/env: use -[v]S to pass options in shebang lines
$ seq 1 2 | $(nix-build '<nixpkgs>' -A coreutils)/bin/env "-S sort -nr"
2
1
GNU Coreutils says FreeBSD's `env` does, though I wonder if FreeBSD's
would be unhappy with the `-S`:
https://www.gnu.org/software/coreutils/manual/html_node/env-invocation.html#env-invocation
BusyBox v1.30.1 does not, and does not have a `-S`-like option:
$ seq 1 2 | $(nix-build '<nixpkgs>' -A busybox)/bin/env "sort -nr"
env: can't execute 'sort -nr': No such file or directory
Toybox 0.8.1 also does not, and also does not have a `-S` option:
$ seq 1 2 | $(nix-build '<nixpkgs>' -A toybox)/bin/env "sort -nr"
env: exec sort -nr: No such file or directory
---
At any rate, if this patch merges and the remaining ~1,500 are updated,
the much larger patch should probably include a checkstyle-like test
asserting all new shebangs use `/usr/bin/env`. I also don't mind
dealing with NixOS weirdness if the project would prefer that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Graham Christensen <graham@grahamc.com>
Closes#9893
We found that our zvol code had some issues with volmode=dev that were
not revealed by ZTS.
Add some basic I/O operations to exercise more code paths in the
volmode test.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9953
Currently SIMD accelerated AES-GCM performance is limited by two
factors:
a. The need to disable preemption and interrupts and save the FPU
state before using it and to do the reverse when done. Due to the
way the code is organized (see (b) below) we have to pay this price
twice for each 16 byte GCM block processed.
b. Most processing is done in C, operating on single GCM blocks.
The use of SIMD instructions is limited to the AES encryption of the
counter block (AES-NI) and the Galois multiplication (PCLMULQDQ).
This leads to the FPU not being fully utilized for crypto
operations.
To solve (a) we do crypto processing in larger chunks while owning
the FPU. An `icp_gcm_avx_chunk_size` module parameter was introduced
to make this chunk size tweakable. It defaults to 32 KiB. This step
alone roughly doubles performance. (b) is tackled by porting and
using the highly optimized openssl AES-GCM assembler routines, which
do all the processing (CTR, AES, GMULT) in a single routine. Both
steps together result in up to 32x reduction of the time spend in
the en/decryption routines, leading up to approximately 12x
throughput increase for large (128 KiB) blocks.
Lastly, this commit changes the default encryption algorithm from
AES-CCM to AES-GCM when setting the `encryption=on` property.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Jason King <jason.king@joyent.com>
Reviewed-By: Tom Caputi <tcaputi@datto.com>
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#9749
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9960
FreeBSD does not have the long opts for wc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9963
And while here, add a workaround for FreeBSD to ensure dirty data is
synced before taking a snapshot, by remounting read-only, then remount
again read-write after the snapshot.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9914
FreeBSD has jails, not zones.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9899
Linux was missing a default value for DEV_DSKDIR. Set it to /dev.
Fix resulting fallout.
SLICE_PREFIX seems like a good candidate for including in the defaults.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9898
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9907
We can avoid a great deal of `sleep 3` by simply destroying the whole
partition table in one shot with gpart.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9908
FreeBSD doesn't support feature@edonr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9901
Both GNU and FreeBSD sort have -R to randomize input.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9900
Allow a range of object identifiers to dump with -d. This may
be useful when dumping a large dataset and you want to break
it up into multiple phases, or to resume where a previous scan
left off. Object type selection flags are supported to reduce
the performance overhead of verbosely dumping unwanted objects,
and to reduce the amount of post-processing work needed to
filter out unwanted objects from zdb output.
This change extends existing syntax in a backward-compatible
way. That is, the base case of a range is to specify a single
object identifier to dump. Ranges and object identifiers can
be intermixed as command line parameters.
Usage synopsis:
Object ranges take the form <start>:<end>[:<flags>]
start Starting object number
end Ending object number, or -1 for no upper bound
flags Optional flags to select object types:
A All objects (this is the default)
d ZFS directories
f ZFS files
m SPA space maps
z ZAPs
- Negate effect of next flag
Examples:
# Dump all file objects
zdb -dd tank/fish 0👎f
# Dump all file and directory objects
zdb -dd tank/fish 0👎fd
# Dump all types except file and directory objects
zdb -dd tank/fish 0👎A-f-d
# Dump object IDs in a specific range
zdb -dd tank/fish 1000:2000
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#9832
Adding the expected PERF_ prefix to RANDSEED, COMPPERCENT,
and COMPCHUNK.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#9877
When used with non-loop devices, zdb_004_pos fails because the disk
argument provided is the partition rather than the expected whole disk
name.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9876
This mostly involves reworking platform checks to make illumos the
exception (thanks to their unusual way of exposing xattrs). Other
platforms are able to take advantage of the recently added xattr
wrappers in libtest.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9872
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9873
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9867
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9867
This adds support in channel programs to inherit properties analogous
to `zfs inherit` by adding `zfs.sync.inherit` and `zfs.check.inherit`
functions to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9738
There doesn't seem to be a need for this complexity.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9854
Ensure the capture ends at the first DVA in case there are multiple
DVAs on the same line by only capturing up to the first '>' character.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9851
Remove the blkid version check from zpool_create_008_pos.ksh
so the test case will not be skipped.
All versions of blkid tested by the CI are either new enough
to not suffer from this issue, or have been patched as is
the case with CentOS 7 (libblkid-2.23.2-61).
Additionally, add a block_device_wait after device partitioning
to ensure the expected partitions will exist.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9853
This check isn't meant to be used for command substitution.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9844
As an alternative to the dataset name, zdb now allows the decimal
or hexadecimal objset ID to be specified. When permanent errors
are reported as 2 hexadecimal numbers (objset ID : object ID) in
zpool status; you can now use 'zdb <pool>[/objset ID] object' to
determine the names of the objset and object which have the error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9733
Making the default FIO output format be JSON thus easier to post process
performance results. To get previous 'normal' output format,
PERF_FIO_FORMAT can be set prior to invoking zfs-tests.sh. For example:
'PERF_FIO_FORMAT=normal ./zfs-tests.sh -T perf -r ./runfiles/perf.run'
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#9847
Every other ksh script has /bin/ksh in the shebang.
If we're going to assume a path, we can at least be consistent.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9845
On FreeBSD grep does not support Perl extensions
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9841
This should have been using egrep.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9840
These are no longer needed after fixing device name matching for whole
disks in libzutil on FreeBSD.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9839
Update tests to use the variables for tunable names.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9831
Fixes the last property having an empty value on FreeBSD and makes the
code a bit more readable.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9834
Create xattr helpers to hide platform and update usage in tests.
This does not generally aim to enable all xattr tests yet, but it is a
necessary step in that direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9826
This commit adds the --saved (-S) to the 'zfs send' command.
This flag allows a user to send a partially received dataset,
which can be useful when migrating a backup server to new
hardware. This flag is compatible with resumable receives, so
even if the saved send is interrupted, it can be resumed.
The flag does not require any user / kernel ABI changes or any
new feature flags in the send stream format.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Reviewed-by: Christian Schwarz <me@cschwarz.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9007
The zts-auto_offline_001_pos test could exceed the 10 minute test
limit and be KILLED by the test infrastructure. To prevent this
speed up the test case by:
* Removing redundant pool configurations. Each of the following
vdev types is tested once: mirror, raidz, cache, and special.
* The block_device_wait function need only wait on the block
device which has been removed as part of the test.
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9827
- Set fixed chunk pattern, for sane compression
- Adjust buffer to blocksize, for cross blocksize repeatability
- Use fixed seed, for improved repeatability
- Move comp-percent and comp-chunk to variables
- set variables (mostly) to old defaults
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#9793
There was a shuf package but the upstream for the port has recently
disappeared, so it is no longer available.
Create a function to hide the usage of shuf. Implement using seq|random
on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9824
The name overlaps with a command needed by FreeBSD.
There is also no sense having two 'random' functions that do nearly
the same thing, so consolidate to just the more general one and name
it 'random_int_between'.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9820
For dedup, special and log devices "zpool add -n" does not print
correctly their vdev type:
~# zpool add -n pool dedup /tmp/dedup special /tmp/special log /tmp/log
would update 'pool' to the following configuration:
pool
/tmp/normal
/tmp/dedup
/tmp/special
/tmp/log
This could lead storage administrators to modify their ZFS pools to
unexpected and unintended vdev configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9783Closes#9390
The cleanup_devices function should remove any partitions created
on the device and force the partition table to be reread. This
is needed to ensure that blkid has an up to date version of what
devices and partitions are used by zfs.
The cleanup_devices call was removed from inuse_008_pos.ksh since
it operated on partitions instead of devices and was not needed.
Lastly ddidecode may be called by parted and was therefore added
to the constrained path.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9806
Replace `test -b` and equivalents with `is_disk_device`, so that `-c`
is used instead on FreeBSD which has no block cache layer for devices.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9795
Neither FreeBSD nor Linux support dumping to zvols.
DilOS still uses these tests, so the files are kept and the tests have
been relocated to sunos.run.
An `is_illumos` function was added to libtest.shlib to eliminate some
awkward platform checks.
A few functions that are not expected to be used outside of illumos
have been sanitized of extraneous FreeBSD adaptations.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9794
The externally faulted vdev should be brought back online and have
its errors cleared before the pool is destroyed. Failure to do so
will leave a vdev with a valid active label. This vdev may then
not be used to create a new pool without the -f flag potentially
leading to subsequent test failures.
Additionally remove an unreachable log_pass from setup.ksh.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9777
Remove a few hardcoded instances of /var/tmp. This should use
the $TEST_BASE_DIR in order to allow the ZTS to be optionally
run in an alternate directory using `zfs-tests.sh -d <path>`.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9775
As of Python 3.5 the default behavior of json.tool was changed to
preserve the input order rather than lexical order. The test case
expects the output to be sorted so apply the --sort-keys option
to the json.tool command when using Python 3.5 and the option is
supported.
https://docs.python.org/3/library/json.html#module-json.tool
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9774
Update the devices_001_pos and devices_002_neg test cases such that the
special block device file created is backed by a ZFS volume. Specifying
a specific device allows the major and minor numbers to be easily
determined. Furthermore, this avoids the potentially dangerous behavior
of opening the first block device we happen to find under /dev/.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9773
Rather than defining a new instance of 'aok' in every compilation
unit which includes this header, there is a single instance
defined in zone.c, and the header now only declares an extern.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Closes#9752
* large_dnode_008_pos - Force a pool sync before invoking zdb to
ensure the updated dnode blocks have been persisted to disk.
* refreserv_raidz - Wait for the /dev/zvol links to be both created
and removed, this is important because the same device volume
names are being used repeatedly.
* btree_test - Add missing .gitignore file for btree_test binary.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9769
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
* devices_001_pos and devices_002_neg - Failing after FreeBSD ZTS
merged due to missing 'function' keyword for create_dev_file_linux.
* pool_state - Occasionally fails due to an insufficient delay
before checking 'zpool status'. Increasing the delay from 1 to 3
seconds resolved the issue in local testing.
* procfs_list_basic - Fails when run in-tree because the logged
command is actually 'lt-zfs'. Updated the regex accordingly.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9748
Additional test cases for the btree implementation, see #9181.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9717
Update the common ZTS scripts and individual test cases as needed
in order to allow them to be run on FreeBSD. The high level goal
is to provide compatibility wrappers whenever possible to minimize
changes to individual test cases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9692
Apply umask to `mode` which will eventually be applied to inode.
This is needed since VFS doesn't apply umask for O_TMPFILE files.
(Note that zpl_init_acl() applies `ip->i_mode &= ~current_umask();`
only when POSIX ACL is used.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#8997Closes#8998
This interferes with zdb_read_block trying all the decompression
algorithms when the 'd' flag is specified, as some are
expected to fail. Also control the output when guessing
algorithms, try the more common compression types first, allow
specifying lsize/psize, and fix an uninitialized variable.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9612Closes#9630
The resilver restart test was reported as failing about 2% of the
time. Two issues were found:
- The event log wasn't large enough, so resilver events were missing
- One 'zpool sync' wasn't enough for resilver to start after zinject
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #9588Closes#9677Closes#9703
This sets send_realloc_files.ksh to use properties.shlib
(like the other compression related tests)
It was missing from #9645
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Issue #9645Closes#9679
FreeBSD uses its own crypto framework in-kernel which, at this time,
has no EDONR implementation.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9664
FreeBSD requires three additional ioctls, they are ZFS_IOC_NEXTBOOT,
ZFS_IOC_JAIL, and ZFS_IOC_UNJAIL. These have been added after the
Linux-specific ioctls. The range 0x80-0xFF has been reserved for
future optional platform-specific ioctls. Any platform may choose
to implement these as appropriate.
None of the existing ioctl numbers have been changed to maintain
compatibility. For Linux no vectors have been registered for the
new ioctls and they are reported as unsupported.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9667
- Moves compression algorithms for tests to properties.shlib
- Removes all compression algorithms levels from general tests
- Replaces on with lz4 for compression tests
- Removes random algorithm selection, if not needed
- Cleans copyright header formatting
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Closes#9645
There may be circumstances where it's desirable that all blocks
in a specified dataset be stored on the special device. Relax
the artificial 128K limit and allow the special_small_blocks
property to be set up to 1M. When blocks >1MB have been enabled
via the zfs_max_recordsize module option, this limit is increased
accordingly.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9131Closes#9355
The `-o ashift` option must appear after attach to be properly
interpreted by getopt(3) on all platforms.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Igor Kozhukhov <igor@dilos.org>
Closes#9636
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #840Closes#9155Closes#9378Closes#9551Closes#9588
The function zdb_read_block (zdb -R) was always intended to have a :c
flag which would read the DVA and length supplied by the user, and
display the checksum. Since we don't know which checksum goes with
the data, we should calculate and display them all.
For each checksum in the table, read in the data at the supplied
DVA:length, calculate the checksum, and display it. Update the man
page and create a zfs test for the new feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9607
The tst.terminate_by_signal test case may occasionally fail when
running in a less consistent virtual environment. For all observed
failures the process was terminated correctly but it took longer than
expected resulting in too many snapshot being created.
To minimize the likelyhood of this occuring increase the threshold
from 50 to 90 snapshots. The larger limit will still verifiy that
the channel program was correctly terminated early.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9601
Use `printf` to properly interpret unicode characters.
Illumos uses a utility called `zlook` to allow additional flags to be
provided to readdir and lookup for testing. This functionality could
be ported to Linux, but even without it several of the tests can be
enabled by instead using the standard `test` command.
Additional, work is required to enable the remaining test cases.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Issue #7633Closes#8812
df58307 removed the need to specify -d 1 when zfs list and zfs get are
called with -t snapshot on a datset. This commit extends the same
behaviour to -t bookmark.
This commit also introduces the 'snap' shorthand for snapshots from
zfs list to zfs get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: InsanePrawn <insane.prawny@gmail.com>
Closes#9589
Reinstate the zpl_revalidate() functionality to resolve a regression
where dentries for open files during a rollback are not invalidated.
The unrelated functionality for automatically unmounting .zfs/snapshots
was not reverted. Nor was the addition of shrink_dcache_sb() to the
zfs_resume_fs() function.
This issue was not immediately caught by the CI because the test case
intended to catch it was included in the list of ZTS tests which may
occasionally fail for unrelated reasons. Remove all of the rollback
tests from this list to help identify the frequency of any spurious
failures.
The rollback_003_pos.ksh test case exposes a real issue with the
long standing code which needs to be investigated. Regardless,
it has been enable with a small workaround in the test case itself.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9587Closes#9592
The removal_with_errors.ksh test case could occasionally complete
the removal process instead of canceling due to an injected error.
To prevent this false positive, export and import the pool between
test phases to flush the ARC cache. Furthermore, double the amount
of data in the pool to increase the removal time.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9528
Currently, when you call 'zfs change-key' on an encrypted dataset
that has an unencrypted child, the code will trigger a VERIFY.
This VERIFY is leftover from before we allowed unencrypted
datasets to exist underneath encrypted ones. This patch fixes the
issue by simply replacing the VERIFY with an early return when
recursing through datasets.
Reviewed by: Jason King <jason.brian.king@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9524
This change leverage module_param_call() to run arc_tuning_update()
immediately after the ARC tunable has been updated as suggested in
cffa8372 code review.
A simple test case is added to the ZFS Test Suite to prevent future
regressions in functionality.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9487Closes#9489
Currently, incremental recursive encrypted receives fail to work
for any snapshot after the first. The reason for this is because
the check in zfs_setup_cmdline_props() did not properly realize
that when the user attempts to use '-x encryption' in this
situation, they are not really overriding the existing encryption
property and instead are attempting to prevent it from changing.
This resulted in an error message stating: "encryption property
'encryption' cannot be set or excluded for raw or incremental
streams".
This problem is fixed by updating the logic to expect this use
case.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9494
O_TMPFILE is not available on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9503
* Use .ksh extension for ksh scripts, not .sh
* Remove .ksh extension from tests in common.run
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9502
With 4k disks, this test will fail in the last section because the
expected human readable value of 20.0M is reported as 20.1M. Rather than
use the human readable property, switch to the parsable property and
verify that the values are reasonably close.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9477
Brian Behlendorf
Georgy Yakovlev
наб
Ryan Moeller
Rich Ercolani
Tony Hutter
Paul Dagnelie
Attila Fülöp
Fedor Uporov
Palash Gandhi
Mike Swanson
youzhongyang
felixdoerre
Ryan Moeller
John Wren Kennedy
Ka Ho Ng
Alexander Motin
George Amanakis
Serapheim Dimitropoulos
Christian Schwarz
Prawn
pablofsf
matt-fidd
Andrea Gelmini
Andrew
George Wilson
Antonio Russo
nssrikanth
Cedric Maunoury
Don Brady
Colm
José Luis Salvador Rufo
George Melikov
Allan Jude
Matthew Ahrens
Will Andrews
Matthew Macy
Brian Atkinson
sterlingjensen
Toomas Soome
loli10K
Tony Perkins
Adam D. Moss
Richard Elling
John Poduska
Tony Nguyen
Michael Niewöhner
Allan Jude
tony-zfs
Arvind Sankar
Robert Novak
adilger
Igor K
alaviss
Paul Dagnelie
Petros Koutoupis
Sara Hartse
alex
Matthew Ahrens
Mariusz Zaborski
Olaf Faaland
Richard Laager
Jason King
Paul Zuchowski
Graham Christensen
Ned Bass
Tom Caputi
Kjeld Schouten-Lebbing
Nick Black
Tomohiro Kusumi
loli10K