This warning indicates the incorrect use of KM_SLEEP in a call
path which must use KM_PUSHPAGE to avoid deadlocking in direct
reclaim. See commit b8d06fca08
for additional details.
SPL: Fixing allocation for task txg_sync (6093) which
used GFP flags 0x297bda7c with PF_NOFS set
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #917
Differences between how paging is done on Solaris and Linux can cause
deadlocks if KM_SLEEP is used in any the following contexts.
* The txg_sync thread
* The zvol write/discard threads
* The zpl_putpage() VFS callback
This is because KM_SLEEP will allow for direct reclaim which may result
in the VM calling back in to the filesystem or block layer to write out
pages. If a lock is held over this operation the potential exists to
deadlock the system. To ensure forward progress all memory allocations
in these contexts must us KM_PUSHPAGE which disables performing any I/O
to accomplish the memory allocation.
Previously, this behavior was acheived by setting PF_MEMALLOC on the
thread. However, that resulted in unexpected side effects such as the
exhaustion of pages in ZONE_DMA. This approach touchs more of the zfs
code, but it is more consistent with the right way to handle these cases
under Linux.
This is patch lays the ground work for being able to safely revert the
following commits which used PF_MEMALLOC:
21ade34 Disable direct reclaim for z_wr_* threads
cfc9a5c Fix zpl_writepage() deadlock
eec8164 Fix ASSERTION(!dsl_pool_sync_context(tx->tx_pool))
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
The vdev queue layer may require a small number of buffers
when attempting to create aggregate I/O requests. Rather than
attempting to allocate them from the global zio buffers, which
is slow under memory pressure, it makes sense to pre-allocate
them because...
1) These buffers are short lived. They are only required for
the life of a single I/O at which point they can be used by
the next I/O.
2) The maximum number of concurrent buffers needed by a vdev is
small. It's roughly limited by the zfs_vdev_max_pending tunable
which defaults to 10.
By keeping a small list of these buffer per-vdev we can ensure
one is always available when we need it. This significantly
reduces contention on the vq->vq_lock, because we no longer
need to perform a slow allocation under this lock. This is
particularly important when memory is already low on the system.
It would probably be wise to extend the use of these buffers beyond
aggregate I/O and in to the raidz implementation. The inability
to quickly allocate buffer for the parity stripes could result in
similiar problems.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This commit used PF_MEMALLOC to prevent a memory reclaim deadlock.
However, commit 49be0ccf1f eliminated
the invocation of __cv_init(), which was the cause of the deadlock.
PF_MEMALLOC has the side effect of permitting pages from ZONE_DMA
to be allocated. The use of PF_MEMALLOC was found to cause stability
problems when doing swap on zvols. Since this technique is known to
cause problems and no longer fixes anything, we revert it.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #726
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#718
After surveying the code, the few places where smp_processor_id is used
were deemed to be safe to use with a preempt enabled kernel. As such, no
core logic had to be changed. These smp_processor_id call sites are simply
are wrapped in kpreempt_disable and kpreempt_enabled to prevent the
Linux kernel from emitting scary warnings.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Issue #83
Export these symbols so they may be used by other ZFS consumers
besides the ZPL.
Remove three stale prototype definites from dbuf.h. The actual
implementations of these functions were removed/renamed long ago.
It would be good in the long term to remove the existing pragmas
we inherited from Solaris and simply use the dbuf_* names.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1693
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#678
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#862
1644 add ZFS "clones" property
1645 add ZFS "written" and "written@..." properties
1646 "zfs send" should estimate size of stream
1647 "zfs destroy" should determine space reclaimed by
destroying multiple snapshots
1708 adjust size of zpool history data
References:
https://www.illumos.org/issues/1644https://www.illumos.org/issues/1645https://www.illumos.org/issues/1646https://www.illumos.org/issues/1647https://www.illumos.org/issues/1708
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. This change has reordered
all of the new ioctl()s to the end of the list. This should
help minimize this issue in the future.
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Albert Lee <trisk@opensolaris.org>
Approved by: Garrett D'Amore <garret@nexenta.com>
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#826Closes#664
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#784
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Gentoo Hardened kernels include the PaX/GRSecurity patches. They use a
dialect of C that relies on a GCC plugin. In particular, struct
file_operations has been marked do_const in the PaX/GRSecurity dialect,
which causes GCC to consider all instances of it as const. This caused
failures in the autotools checks and the ZFS source code.
To address this, we modify the autotools checks to take into account
differences between the PaX C dialect and the regular C dialect. We also
modify struct zfs_acl's z_ops member to be a pointer to a function
pointer table. Lastly, we modify zpl_put_link() to address a PaX change
to the function prototype of nd_get_link(). This avoids compiler errors
in the PaX/GRSecurity dialect.
Note that the change in zpl_put_link() causes a warning that becomes a
build failure when debugging is enabled. Fixing that warning requires
ryao/spl@5ca50ef459.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#484
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
1949 crash during reguid causes stale config
1953 allow and unallow missing from zpool history since removal of pyzfs
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Garrett D'Amore <garrett.damore@gmail.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Steve Gonczi <gonczi@comcast.net>
Approved by: Eric Schrock <eric.schrock@delphix.com>
References:
https://www.illumos.org/issues/1949https://www.illumos.org/issues/1953
Ported by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Igor Kozhukhov <ikozhukhov@gmail.com>
Reviewed by: Alexander Eremin <alexander.eremin@nexenta.com>
Reviewed by: Alexander Stetsenko <ams@nexenta.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/1748
This commit modifies the user to kernel space ioctl ABI. Extra
care should be taken when updating to ensure both the kernel
modules and utilities are updated. If only the user space
component is updated both the 'zpool events' command and the
'zpool reguid' command will not work until the kernel modules
are updated.
Ported by: Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#665
The lack of the ULL suffix causes warnings such as the following on
32-bit systems:
In function 'zfsctl_is_snapdir':
zfs-0.6.0//module/zfs/zfs_ctldir.c:151: warning: integer constant
is too large for 'long' type
We add the ULL suffix to fix that.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#813
The performance of the ZIL is usually the main bottleneck when dealing with
synchronous, write-heavy workloads (e.g. databases). Understanding the
behavior of the ZIL is required to diagnose performance issues for these
workloads, and to tune ZIL parameters (like zil_slog_limit) accordingly.
This commit adds a new kstat page dedicated to the ZIL with some counters
which, hopefully, scheds some light into what the ZIL is doing, and how it is
doing it.
Currently, these statistics are available in /proc/spl/kstat/zfs/zil.
A description of the fields can be found in zil.h.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#786
FreeBSD #xxx: Dramatically optimize listing snapshots when user
requests only snapshot names and wants to sort them by name, ie.
when executes:
# zfs list -t snapshot -o name -s name
Because only name is needed we don't have to read all snapshot
properties.
Below you can find how long does it take to list 34509 snapshots
from a single disk pool before and after this change with cold and
warm cache:
before:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 525s
warm cache: 218s
after:
# time zfs list -t snapshot -o name -s name > /dev/null
cold cache: 1.7s
warm cache: 1.1s
NOTE: This patch only appears in FreeBSD. If/when Illumos picks up
the change we may want to drop this patch and adopt their version.
However, for now this addresses a real issue.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #450
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
1952 memory leak when adding a file-based l2arc device
1954 leak in ZFS from metaslab_group_create and zfs_ereport_checksum
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Approved by: Eric Schrock <eric.schrock@delphix.com>
References to Illumos issues:
https://www.illumos.org/issues/1951https://www.illumos.org/issues/1952https://www.illumos.org/issues/1954
Ported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#650
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
Add a SA interface which allows us to release the spill block
from a SA handle without destroying the handle. This is useful
because we can then ensure that a copy of the dirty spill block
is not made at sync time due to the extra hold. Susequent calls
to sa_update() or sa_lookup() with transparently refetch the
spill block dbuf from the ARC hash.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Keep counters for the various reasons that a thread may end up
in txg_wait_open() waiting on a new txg. This can be useful
when attempting to determine why a particular workload is
under performing.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
DISCARD (REQ_DISCARD, BLKDISCARD) is useful for thin provisioning.
It allows ZVOL clients to discard (unmap, trim) block ranges from
a ZVOL, thus optimizing disk space usage by allowing a ZVOL to
shrink instead of just grow.
We can't use zfs_space() or zfs_freesp() here, since these functions
only work on regular files, not volumes. Fortunately we can use the
low-level function dmu_free_long_range() which does exactly what we
want.
Currently the discard operation is not added to the log. That's not
a big deal since losing discard requests cannot result in data
corruption. It would however result in disk space usage higher than
it should be. Thus adding log support to zvol_discard() is probably
a good idea for a future improvement.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
The Linux block device queue subsystem exposes a number of configurable
settings described in Linux block/blk-settings.c. The defaults for these
settings are tuned for hard drives, and are not optimized for ZVOLs. Proper
configuration of these options would allow upper layers (I/O scheduler) to
take better decisions about write merging and ordering.
Detailed rationale:
- max_hw_sectors is set to unlimited (UINT_MAX). zvol_write() is able to
handle writes of any size, so there's no reason to impose a limit. Let the
upper layer decide.
- max_segments and max_segment_size are set to unlimited. zvol_write() will
copy the requests' contents into a dbuf anyway, so the number and size of
the segments are irrelevant. Let the upper layer decide.
- physical_block_size and io_opt are set to the ZVOL's block size. This
has the potential to somewhat alleviate issue #361 for ZVOLs, by warning
the upper layers that writes smaller than the volume's block size will be
slow.
- The NONROT flag is set to indicate this isn't a rotational device.
Although the backing zpool might be composed of rotational devices, the
resulting ZVOL often doesn't exhibit the same behavior due to the COW
mechanisms used by ZFS. Setting this flag will prevent upper layers from
making useless decisions (such as reordering writes) based on incorrect
assumptions about the behavior of the ZVOL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zvol_write() assumes that the write request must be written to stable storage
if rq_is_sync() is true. Unfortunately, this assumption is incorrect. Indeed,
"sync" does *not* mean what we think it means in the context of the Linux
block layer. This is well explained in linux/fs.h:
WRITE: A normal async write. Device will be plugged.
WRITE_SYNC: Synchronous write. Identical to WRITE, but passes down
the hint that someone will be waiting on this IO
shortly.
WRITE_FLUSH: Like WRITE_SYNC but with preceding cache flush.
WRITE_FUA: Like WRITE_SYNC but data is guaranteed to be on
non-volatile media on completion.
In other words, SYNC does not *mean* that the write must be on stable storage
on completion. It just means that someone is waiting on us to complete the
write request. Thus triggering a ZIL commit for each SYNC write request on a
ZVOL is unnecessary and harmful for performance. To make matters worse, ZVOL
users have no way to express that they actually want data to be written to
stable storage, which means the ZIL is broken for ZVOLs.
The request for stable storage is expressed by the FUA flag, so we must
commit the ZIL after the write if the FUA flag is set. In addition, we must
commit the ZIL before the write if the FLUSH flag is set.
Also, we must inform the block layer that we actually support FLUSH and FUA.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The second argument of sops->show_options() was changed from a
'struct vfsmount *' to a 'struct dentry *'. Add an autoconf check
to detect the API change and then conditionally define the expected
interface. In either case we are only interested in the zfs_sb_t.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#549
Historically the internal zfs debug infrastructure has been
scattered throughout the code. Since we expect to start making
more use of this code this patch performs some cleanup.
* Consolidate the zfs debug infrastructure in the zfs_debug.[ch]
files. This includes moving the zfs_flags and zfs_recover
variables, plus moving the zfs_panic_recover() function.
* Remove the existing unused functionality in zfs_debug.c and
replace it with code which correctly utilized the spl logging
infrastructure.
* Remove the __dprintf() function from zfs_ioctl.c. This is
dead code, the dprintf() functionality in the kernel relies
on the spl log support.
* Remove dprintf() from hdr_recl(). This wasn't particularly
useful and was missing the required format specifier anyway.
* Subsequent patches should unify the dprintf() and zfs_dbgmsg()
functions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When the original build system code was added the release
component was accidentally omited from the development header
install path. This patch adds the missing path component so
it's always clear exactly what release your compiling against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Originally, the per-file link limit was set to 65536 because the
exact Linux VFS limit was unclear. Internally ZFS is able to
support 64-bit link counts. After a more careful investigation
the limit can be safely raised to 2^31-1.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#514
The Linux 3.1 kernel has introduced the concept of per-filesystem
shrinkers which are directly assoicated with a super block. Prior
to this change there was one shared global shrinker.
The zfs code relied on being able to call the global shrinker when
the arc_meta_limit was exceeded. This would cause the VFS to drop
references on a fraction of the dentries in the dcache. The ARC
could then safely reclaim the memory used by these entries and
honor the arc_meta_limit. Unfortunately, when per-filesystem
shrinkers were added the old interfaces were made unavailable.
This change adds support to use the new per-filesystem shrinker
interface so we can continue to honor the arc_meta_limit. The
major benefit of the new interface is that we can now target
only the zfs filesystem for dentry and inode pruning. Thus we
can minimize any impact on the caching of other filesystems.
In the context of making this change several other important
issues related to managing the ARC were addressed, they include:
* The dnlc_reduce_cache() function which was called by the ARC
to drop dentries for the Posix layer was replaced with a generic
zfs_prune_t callback. The ZPL layer now registers a callback to
drop these dentries removing a layering violation which dates
back to the Solaris code. This callback can also be used by
other ARC consumers such as Lustre.
arc_add_prune_callback()
arc_remove_prune_callback()
* The arc_reduce_dnlc_percent module option has been changed to
arc_meta_prune for clarity. The dnlc functions are specific to
Solaris's VFS and have already been largely eliminated already.
The replacement tunable now represents the number of bytes the
prune callback will request when invoked.
* Less aggressively invoke the prune callback. We used to call
this whenever we exceeded the arc_meta_limit however that's not
strictly correct since it results in over zeleous reclaim of
dentries and inodes. It is now only called once the arc_meta_limit
is exceeded and every effort has been made to evict other data from
the ARC cache.
* More promptly manage exceeding the arc_meta_limit. When reading
meta data in to the cache if a buffer was unable to be recycled
notify the arc_reclaim thread to invoke the required prune.
* Added arcstat_prune kstat which is incremented when the ARC
is forced to request that a consumer prune its cache. Remember
this will only occur when the ARC has no other choice. If it
can evict buffers safely without invoking the prune callback
it will.
* This change is also expected to resolve the unexpect collapses
of the ARC cache. This would occur because when exceeded just the
arc_meta_limit reclaim presure would be excerted on the arc_c
value via arc_shrink(). This effectively shrunk the entire cache
when really we just needed to reclaim meta data.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#466Closes#292
Directly changing inode->i_nlink is deprecated in Linux 3.2 by commit
SHA: bfe8684869601dacfcb2cd69ef8cfd9045f62170
Use the new set_nlink() kernel function instead.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #462
Added the necessary build infrastructure for building packages
compatible with the Arch Linux distribution. As such, one can now run:
$ ./configure
$ make pkg # Alternatively, one can run 'make arch' as well
on the Arch Linux machine to create two binary packages compatible with
the pacman package manager, one for the zfs userland utilities and
another for the zfs kernel modules. The new packages can then be
installed by running:
# pacman -U $package.pkg.tar.xz
In addition, source-only packages suitable for an Arch Linux chroot
environment or remote builder can also be build using the 'sarch' make
rule.
NOTE: Since the source dist tarball is created on the fly from the head
of the build tree, it's MD5 hash signature will be continually influx.
As a result, the md5sum variable was intentionally omitted from the
PKGBUILD files, and the '--skipinteg' makepkg option is used. This may
or may not have any serious security implications, as the source tarball
is not being downloaded from an outside source.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#491
It has been observed that some of the hottest locks are those
of the zio taskqs. Contention on these locks can limit the
rate at which zios are dispatched which limits performance.
This upstream change from Illumos uses new interface to the
taskqs which allow them to utilize a prealloc'ed taskq_ent_t.
This removes the need to perform an allocation at dispatch
time while holding the contended lock. This has the effect
of improving system performance.
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Alexey Zaytsev <alexey.zaytsev@nexenta.com>
Reviewed by: Jason Brian King <jason.brian.king@gmail.com>
Reviewed by: George Wilson <gwilson@zfsmail.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References to Illumos issue:
https://www.illumos.org/issues/734
Ported-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#482
The current ZFS implementation stores xattrs on disk using a hidden
directory. In this directory a file name represents the xattr name
and the file contexts are the xattr binary data. This approach is
very flexible and allows for arbitrarily large xattrs. However,
it also suffers from a significant performance penalty. Accessing
a single xattr can requires up to three disk seeks.
1) Lookup the dnode object.
2) Lookup the dnodes's xattr directory object.
3) Lookup the xattr object in the directory.
To avoid this performance penalty Linux filesystems such as ext3
and xfs try to store the xattr as part of the inode on disk. When
the xattr is to large to store in the inode then a single external
block is allocated for them. In practice most xattrs are small
and this approach works well.
The addition of System Attributes (SA) to zfs provides us a clean
way to make this optimization. When the dataset property 'xattr=sa'
is set then xattrs will be preferentially stored as System Attributes.
This allows tiny xattrs (~100 bytes) to be stored with the dnode and
up to 64k of xattrs to be stored in the spill block. If additional
xattr space is required, which is unlikely under Linux, they will be
stored using the traditional directory approach.
This optimization results in roughly a 3x performance improvement
when accessing xattrs which brings zfs roughly to parity with ext4
and xfs (see table below). When multiple xattrs are stored per-file
the performance improvements are even greater because all of the
xattrs stored in the spill block will be cached.
However, by default SA based xattrs are disabled in the Linux port
to maximize compatibility with other implementations. If you do
enable SA based xattrs then they will not be visible on platforms
which do not support this feature.
----------------------------------------------------------------------
Time in seconds to get/set one xattr of N bytes on 100,000 files
------+--------------------------------+------------------------------
| setxattr | getxattr
bytes | ext4 xfs zfs-dir zfs-sa | ext4 xfs zfs-dir zfs-sa
------+--------------------------------+------------------------------
1 | 2.33 31.88 21.50 4.57 | 2.35 2.64 6.29 2.43
32 | 2.79 30.68 21.98 4.60 | 2.44 2.59 6.78 2.48
256 | 3.25 31.99 21.36 5.92 | 2.32 2.71 6.22 3.14
1024 | 3.30 32.61 22.83 8.45 | 2.40 2.79 6.24 3.27
4096 | 3.57 317.46 22.52 10.73 | 2.78 28.62 6.90 3.94
16384 | n/a 2342.39 34.30 19.20 | n/a 45.44 145.90 7.55
65536 | n/a 2941.39 128.15 131.32* | n/a 141.92 256.85 262.12*
Legend:
* ext4 - Stock RHEL6.1 ext4 mounted with '-o user_xattr'.
* xfs - Stock RHEL6.1 xfs mounted with default options.
* zfs-dir - Directory based xattrs only.
* zfs-sa - Prefer SAs but spill in to directories as needed, a
trailing * indicates overflow in to directories occured.
NOTE: Ext4 supports 4096 bytes of xattr name/value pairs per file.
NOTE: XFS and ZFS have no limit on xattr name/value pairs per file.
NOTE: Linux limits individual name/value pairs to 65536 bytes.
NOTE: All setattr/getattr's were done after dropping the cache.
NOTE: All tests were run against a single hard drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #443
Update the code to use the bdi_setup_and_register() helper to
simplify the bdi integration code. The updated code now just
registers the bdi during mount and destroys it during unmount.
The only complication is that for 2.6.32 - 2.6.33 kernels the
helper wasn't available so in these cases the zfs code must
provide it. Luckily the bdi_setup_and_register() function
is trivial.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#367
Profiling the system during meta data intensive workloads such
as creating/removing millions of files, revealed that the system
was cpu bound. A large fraction of that cpu time was being spent
waiting on the virtual address space spin lock.
It turns out this was caused by certain heavily used kmem_caches
being backed by virtual memory. By default a kmem_cache will
dynamically determine the type of memory used based on the object
size. For large objects virtual memory is usually preferable
and for small object physical memory is a better choice. See
the spl_slab_alloc() function for a longer discussion on this.
However, there is a certain amount of gray area when defining a
'large' object. For the following caches it turns out they were
just over the line:
* dnode_cache
* zio_cache
* zio_link_cache
* zio_buf_512_cache
* zfs_data_buf_512_cache
Now because we know there will be a lot of churn in these caches,
and because we know the slabs will still be reasonably sized.
We can safely request with the KMC_KMEM flag that the caches be
backed with physical memory addresses. This entirely avoids the
need to serialize on the virtual address space lock.
As a bonus this also reduces our vmalloc usage which will be good
for 32-bit kernels which have a very small virtual address space.
It will also probably be good for interactive performance since
unrelated processes could also block of this same global lock.
Finally, we may see less cpu time being burned in the arc_reclaim
and txg_sync_threads.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #258
An incomplete guid_to_ds_map would cause restore_write_byref() to fail
while receiving a de-duplicated backup stream.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Garrett D`Amore <garrett@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References to Illumos issue and patch:
- https://www.illumos.org/issues/755
- https://github.com/illumos/illumos-gate/commit/ec5cf9d53a
Signed-off-by: Gunnar Beutner <gunnar@beutner.name>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#372
Export all symbols already marked extern in the zfs_vfsops.h
header. Several non-static symbols have also been added to
the header and exportewd. This allows external modules to
more easily create and manipulate properly created ZFS
filesystem type datasets.
Rename zfsvfs_teardown() to zfs_sb_teardown and export it.
This is done simply for consistency with the rest of the code
base. All other zfsvfs_* functions have already been renamed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Export all the symbols for the system attribute (SA) API. This
allows external module to cleanly manipulate the SAs associated
with a dnode. Documention for the SA API can be found in the
module/zfs/sa.c source.
This change also removes the zfs_sa_uprade_pre, and
zfs_sa_uprade_post prototypes. The functions themselves were
dropped some time ago.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Export all the symbols for the ZAP API. This allows external modules
to cleanly interface with ZAP type objects. Previously only a subset
of the functionality was exposed. Documention for the ZAP API can be
found in the sys/zap.h header.
This change also removes a duplicate zap_increment_int() prototype.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
GPT's created by libefi set the HeaderSize attribute in the GPT
header to 512 -- size of the GPT header INCLUDING the 420 padding
bytes at the end. Most other tools set the size to 92 -- size of
the actual header itself excluding the padding. Most tools check
the recorded HeaderSize when verifying CRC, but gptfdisk hardcodes
92 and thus reports CRC verification problems for full-disk vdevs
created IE with `zpool create pool sdc`.
This commit changes libefi's behavior for GPT creation and also
fixes several edge cases where libefi's behavior was similar
(though in an incompatible manner) to gptfdisk. Libefi assumed
HeaderSize was always 512 even if the GPT recorded a different
value. Sanity checks of the GPT headersize read from disk were
added before applying checksum calculation -- this will prevent
segfault in cases of bogus on-disk values.
Zpools created with the resuling libefi are verified as correct
both by parted and gptfdisk. Also pool have been tested to
import correctly on ZFS on Linux as well as Solaris Express 11
livecd.
Signed-off-by: Zachary Bedell <zac@thebedells.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#344
For a long time now the kernel has been moving away from using the
pdflush daemon to write 'old' dirty pages to disk. The primary reason
for this is because the pdflush daemon is single threaded and can be
a limiting factor for performance. Since pdflush sequentially walks
the dirty inode list for each super block any delay in processing can
slow down dirty page writeback for all filesystems.
The replacement for pdflush is called bdi (backing device info). The
bdi system involves creating a per-filesystem control structure each
with its own private sets of queues to manage writeback. The advantage
is greater parallelism which improves performance and prevents a single
filesystem from slowing writeback to the others.
For a long time both systems co-existed in the kernel so it wasn't
strictly required to implement the bdi scheme. However, as of
Linux 2.6.36 kernels the pdflush functionality has been retired.
Since ZFS already bypasses the page cache for most I/O this is only
an issue for mmap(2) writes which must go through the page cache.
Even then adding this missing support for newer kernels was overlooked
because there are other mechanisms which can trigger writeback.
However, there is one critical case where not implementing the bdi
functionality can cause problems. If an application handles a page
fault it can enter the balance_dirty_pages() callpath. This will
result in the application hanging until the number of dirty pages in
the system drops below the dirty ratio.
Without a registered backing_device_info for the filesystem the
dirty pages will not get written out. Thus the application will hang.
As mentioned above this was less of an issue with older kernels because
pdflush would eventually write out the dirty pages.
This change adds a backing_device_info structure to the zfs_sb_t
which is already allocated per-super block. It is then registered
when the filesystem mounted and unregistered on unmount. It will
not be registered for mounted snapshots which are read-only. This
change will result in flush-<pool> thread being dynamically created
and destroyed per-mounted filesystem for writeback.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#174
Brian Behlendorf
Richard Yao
Prakash Surya
Dan McDonald
Etienne Dechamps
Matthew Ahrens
George Wilson
Garrett D'Amore
Pawel Jakub Dawidek
Richard Yao
George Wilson
Darik Horn
Alexander Stetsenko
Zachary Bedell