When reading compressed blocks from the L2ARC, with
compressed ARC disabled, arc_hdr_size() returns
LSIZE rather than PSIZE, but the actual read is PSIZE.
This causes l2arc_read_done() to compare the checksum
against the wrong size, resulting in checksum failure.
This manifests as an increase in the kstat l2_cksum_bad
and the read being retried from the main pool, making the
L2ARC ineffective.
Add new L2ARC tests with Compressed ARC enabled/disabled
Blocks are handled differently depending on the state of the
zfs_compressed_arc_enabled tunable.
If a block is compressed on-disk, and compressed_arc is enabled:
- the block is read from disk
- It is NOT decompressed
- It is added to the ARC in its compressed form
- l2arc_write_buffers() may write it to the L2ARC (as is)
- l2arc_read_done() compares the checksum to the BP (compressed)
However, if compressed_arc is disabled:
- the block is read from disk
- It is decompressed
- It is added to the ARC (uncompressed)
- l2arc_write_buffers() will use l2arc_apply_transforms() to
recompress the block, before writing it to the L2ARC
- l2arc_read_done() compares the checksum to the BP (compressed)
- l2arc_read_done() will use l2arc_untransform() to uncompress it
This test writes out a test file to a pool consisting of one disk
and one cache device, then randomly reads from it. Since the arc_max
in the tests is low, this will feed the L2ARC, and result in reads
from the L2ARC.
We compare the value of the kstat l2_cksum_bad before and after
to determine if any blocks failed to survive the trip through the
L2ARC.
Sponsored-by: The FreeBSD Foundation
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Closes#10693
The `zfs program` subcommand invokes a LUA interpreter to run ZFS
"channel programs". This interpreter runs in a constrained environment,
with defined memory limits. The LUA stack (used for LUA functions that
call each other) is allocated in the kernel's heap, and is limited by
the `-m MEMORY-LIMIT` flag and the `zfs_lua_max_memlimit` module
parameter. The C stack is used by certain LUA features that are
implemented in C. The C stack is limited by `LUAI_MAXCCALLS=20`, which
limits call depth.
Some LUA C calls use more stack space than others, and `gsub()` uses an
unusually large amount. With a programming trick, it can be invoked
recursively using the C stack (rather than the LUA stack). This
overflows the 16KB Linux kernel stack after about 11 iterations, less
than the limit of 20.
One solution would be to decrease `LUAI_MAXCCALLS`. This could be made
to work, but it has a few drawbacks:
1. The existing test suite does not pass with `LUAI_MAXCCALLS=10`.
2. There may be other LUA functions that use a lot of stack space, and
the stack space may change depending on compiler version and options.
This commit addresses the problem by adding a new limit on the amount of
free space (in bytes) remaining on the C stack while running the LUA
interpreter: `LUAI_MINCSTACK=4096`. If there is less than this amount
of stack space remaining, a LUA runtime error is generated.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10611Closes#10613
== Motivation and Context
The current implementation of 'sharenfs' and 'sharesmb' relies on
the use of the sharetab file. The use of this file is os-specific
and not required by linux or freebsd. Currently the code must
maintain updates to this file which adds complexity and presents
a significant performance impact when sharing many datasets. In
addition, concurrently running 'zfs sharenfs' command results in
missing entries in the sharetab file leading to unexpected failures.
== Description
This change removes the sharetab logic from the linux and freebsd
implementation of 'sharenfs' and 'sharesmb'. It still preserves an
os-specific library which contains the logic required for sharing
NFS or SMB. The following entry points exist in the vastly simplified
libshare library:
- sa_enable_share -- shares a dataset but may not commit the change
- sa_disable_share -- unshares a dataset but may not commit the change
- sa_is_shared -- determine if a dataset is shared
- sa_commit_share -- notify NFS/SMB subsystem to commit the shares
- sa_validate_shareopts -- determine if sharing options are valid
The sa_commit_share entry point is provided as a performance enhancement
and is not required. The sa_enable_share/sa_disable_share may commit
the share as part of the implementation. Libshare provides a framework
for both NFS and SMB but some operating systems may not fully support
these protocols or all features of the protocol.
NFS Operation:
For linux, libshare updates /etc/exports.d/zfs.exports to add
and remove shares and then commits the changes by invoking
'exportfs -r'. This file, is automatically read by the kernel NFS
implementation which makes for better integration with the NFS systemd
service. For FreeBSD, libshare updates /etc/zfs/exports to add and
remove shares and then commits the changes by sending a SIGHUP to
mountd.
SMB Operation:
For linux, libshare adds and removes files in /var/lib/samba/usershares
by calling the 'net' command directly. There is no need to commit the
changes. FreeBSD does not support SMB.
== Performance Results
To test sharing performance we created a pool with an increasing number
of datasets and invoked various zfs actions that would enable and
disable sharing. The performance testing was limited to NFS sharing.
The following tests were performed on an 8 vCPU system with 128GB and
a pool comprised of 4 50GB SSDs:
Scale testing:
- Share all filesystems in parallel -- zfs sharenfs=on <dataset> &
- Unshare all filesystems in parallel -- zfs sharenfs=off <dataset> &
Functional testing:
- share each filesystem serially -- zfs share -a
- unshare each filesystem serially -- zfs unshare -a
- reset sharenfs property and unshare -- zfs inherit -r sharenfs <pool>
For 'zfs sharenfs=on' scale testing we saw an average reduction in time
of 89.43% and for 'zfs sharenfs=off' we saw an average reduction in time
of 83.36%.
Functional testing also shows a huge improvement:
- zfs share -- 97.97% reduction in time
- zfs unshare -- 96.47% reduction in time
- zfs inhert -r sharenfs -- 99.01% reduction in time
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Bryant G. Ly <bryangly@gmail.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-68690
Closes#1603Closes#7692Closes#7943Closes#10300
The device_rebuild feature enables sequential reconstruction when
resilvering. Mirror vdevs can be rebuilt in LBA order which may
more quickly restore redundancy depending on the pools average block
size, overall fragmentation and the performance characteristics
of the devices. However, block checksums cannot be verified
as part of the rebuild thus a scrub is automatically started after
the sequential resilver completes.
The new '-s' option has been added to the `zpool attach` and
`zpool replace` command to request sequential reconstruction
instead of healing reconstruction when resilvering.
zpool attach -s <pool> <existing vdev> <new vdev>
zpool replace -s <pool> <old vdev> <new vdev>
The `zpool status` output has been updated to report the progress
of sequential resilvering in the same way as healing resilvering.
The one notable difference is that multiple sequential resilvers
may be in progress as long as they're operating on different
top-level vdevs.
The `zpool wait -t resilver` command was extended to wait on
sequential resilvers. From this perspective they are no different
than healing resilvers.
Sequential resilvers cannot be supported for RAIDZ, but are
compatible with the dRAID feature being developed.
As part of this change the resilver_restart_* tests were moved
in to the functional/replacement directory. Additionally, the
replacement tests were renamed and extended to verify both
resilvering and rebuilding.
Original-patch-by: Isaac Huang <he.huang@intel.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: John Poduska <jpoduska@datto.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10349
The block histogram tracks the changes to psize, lsize and asize
both in the count of the number of blocks (by blocksize) and the
total length of all of the blocks for that blocksize. It also
keeps a running total of the cumulative size of all of the blocks
up to each size to help determine the size of caching SSDs to be
added to zfs hardware deployments.
The block history counts and lengths are summarized in bins
which are powers of two. Even rows with counts of zero are printed.
This change is accessed by specifying one of two options:
zdb -bbb pool
zdb -Pbbb pool
The first version prints the table in fixed size columns.
The second prints in "parseable" output that can be placed into
a CSV file.
Fixed Column, nicenum output sample:
block psize lsize asize
size Count Length Cum. Count Length Cum. Count Length Cum.
512: 3.50K 1.75M 1.75M 3.43K 1.71M 1.71M 3.41K 1.71M 1.71M
1K: 3.65K 3.67M 5.43M 3.43K 3.44M 5.15M 3.50K 3.51M 5.22M
2K: 3.45K 6.92M 12.3M 3.41K 6.83M 12.0M 3.59K 7.26M 12.5M
4K: 3.44K 13.8M 26.1M 3.43K 13.7M 25.7M 3.49K 14.1M 26.6M
8K: 3.42K 27.3M 53.5M 3.41K 27.3M 53.0M 3.44K 27.6M 54.2M
16K: 3.43K 54.9M 108M 3.50K 56.1M 109M 3.42K 54.7M 109M
32K: 3.44K 110M 219M 3.41K 109M 218M 3.43K 110M 219M
64K: 3.41K 218M 437M 3.41K 218M 437M 3.44K 221M 439M
128K: 3.41K 437M 874M 3.70K 474M 911M 3.41K 437M 876M
256K: 3.41K 874M 1.71G 3.41K 874M 1.74G 3.41K 874M 1.71G
512K: 3.41K 1.71G 3.41G 3.41K 1.71G 3.45G 3.41K 1.71G 3.42G
1M: 3.41K 3.41G 6.82G 3.41K 3.41G 6.86G 3.41K 3.41G 6.83G
2M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
4M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
8M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
16M: 0 0 6.82G 0 0 6.86G 0 0 6.83G
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Robert E. Novak <novak5@llnl.gov>
Closes: #9158Closes#10315
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
The l2arc_evict() function is responsible for evicting buffers which
reference the next bytes of the L2ARC device to be overwritten. Teach
this function to additionally TRIM that vdev space before it is
overwritten if the device has been filled with data. This is done by
vdev_trim_simple() which trims by issuing a new type of TRIM,
TRIM_TYPE_SIMPLE.
We also implement a "Trim Ahead" feature. It is a zfs module parameter,
expressed in % of the current write size. This trims ahead of the
current write size. A minimum of 64MB will be trimmed. The default is 0
which disables TRIM on L2ARC as it can put significant stress to
underlying storage devices. To enable TRIM on L2ARC we set
l2arc_trim_ahead > 0.
We also implement TRIM of the whole cache device upon addition to a
pool, pool creation or when the header of the device is invalid upon
importing a pool or onlining a cache device. This is dependent on
l2arc_trim_ahead > 0. TRIM of the whole device is done with
TRIM_TYPE_MANUAL so that its status can be monitored by zpool status -t.
We save the TRIM state for the whole device and the time of completion
on-disk in the header, and restore these upon L2ARC rebuild so that
zpool status -t can correctly report them. Whole device TRIM is done
asynchronously so that the user can export of the pool or remove the
cache device while it is trimming (ie if it is too slow).
We do not TRIM the whole device if persistent L2ARC has been disabled by
l2arc_rebuild_enabled = 0 because we may not want to lose all cached
buffers (eg we may want to import the pool with
l2arc_rebuild_enabled = 0 only once because of memory pressure). If
persistent L2ARC has been disabled by setting the module parameter
l2arc_rebuild_blocks_min_l2size to a value greater than the size of the
cache device then the whole device is trimmed upon creation or import of
a pool if l2arc_trim_ahead > 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam D. Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9713Closes#9789Closes#10224
Small program that converts a dataset id and an object id to a path
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10204
When a resilver finishes, vdev_dtl_reassess is called to hopefully
excise DTL_MISSING (amongst other things). If there are errors during
the resilver, they are tracked in DTL_SCRUB, as spelled out in the
block comment in vdev.c. DTL_SCRUB is in-core only, so it can only
be used if the pool was online for the whole resilver. This state is
tracked with the spa_scrub_started flag, which only gets set when
the scan is initialized. Unfortunately, this flag gets cleared right
before vdev_dtl_reassess gets called, so if there are any errors
during the scan, DTL_MISSING will never get excised and the resilver
will just continually restart. This fix simply moves clearing that
flag until after the call to vdev_dtl_reasses.
In addition, if a pool is imported and already has scn_errors > 0,
this change will restart the resilver immediately instead of doing
the rest of the scan and then restarting it from the beginning. On
the other hand, if scn_errors == 0 at import, then no errors have
been encountered so far, so the spa_scrub_started flag can be safely
set.
A test has been added to verify that resilver does not restart when
relevant DTL's are available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10291
When a top-level vdev is removed from a pool it is converted to an
indirect vdev. Until now splitting such mirrored pools was not possible
with zpool split. This patch enables handling of indirect vdevs and
splitting of those pools with zpool split.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10283
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: sara hartse <sara.hartse@delphix.com>
Closes#10243
Deduplicated send streams (i.e. `zfs send -D` and `zfs receive` of such
streams) are deprecated. Deduplicated send streams can be received by
first converting them to non-deduplicated with the `zstream redup`
command.
This commit removes the code for sending and receiving deduplicated send
streams. `zfs send -D` will now print a warning, ignore the `-D` flag,
and generate a regular (non-deduplicated) send stream. `zfs receive` of
a deduplicated send stream will print an error message and fail.
The resulting code simplification (especially in the kernel's support
for receiving dedup streams) should help enable future performance
enhancements.
Several new tests are added which leverage `zstream redup`.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #7887
Issue #10117
Issue #10156Closes#10212
Add the FreeBSD platform code to the OpenZFS repository. As of this
commit the source can be compiled and tested on FreeBSD 11 and 12.
Subsequent commits are now required to compile on FreeBSD and Linux.
Additionally, they must pass the ZFS Test Suite on FreeBSD which is
being run by the CI. As of this commit 1230 tests pass on FreeBSD
and there are no unexpected failures.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#898Closes#8987
Commit 379ca9c removed the requirement on aux devices to be block
devices only but the test case cache_010_neg was not updated, making it
fail consistently.
This change changes the test to check that cache devices _can_ be
anything that presents a block interface. The testcase is renamed to
cache_010_pos and the exceptions for known failure removed from the test
runner.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alex John <alex@stty.io>
Closes#10172
Add a mechanism to wait for delete queue to drain.
When doing redacted send/recv, many workflows involve deleting files
that contain sensitive data. Because of the way zfs handles file
deletions, snapshots taken quickly after a rm operation can sometimes
still contain the file in question, especially if the file is very
large. This can result in issues for redacted send/recv users who
expect the deleted files to be redacted in the send streams, and not
appear in their clones.
This change duplicates much of the zpool wait related logic into a
zfs wait command, which can be used to wait until the internal
deleteq has been drained. Additional wait activities may be added
in the future.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9707
Increasing l2arc_write_size or l2arc_write_boost can result in
l2arc_write_buffers() not having enough space to perform its writes and
panic zio_write_phys().
Instead of resetting l2ad_hand to l2ad_start at the end of
l2arc_write_buffers() and not taking into account a possible
user-mediated increase of l2arc_write_max, we do this in l2arc_evict(),
right after l2arc_write_size() has run. If there is not enough space to
evict (ie we will exceed l2ad_end) we evict to the end of the device,
reset l2ad_hand to l2ad_start, set l2ad_first to 0 and iterate
l2arc_evict(). We avoid infinite iteration of l2arc_evict() by making
sure in l2arc_write_size() that l2ad_start + size does not exceed
l2ad_end.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10154
Currently when the dataset is in use we can't receive snapshots.
zfs send test/1@asd | zfs recv -FM test/2
cannot unmount '/test/2': Device busy
This commits add option 'M' which attempts to forcibly unmount the
dataset. Thanks to this we can enforce receiving snapshots in a
single step.
Note that this functionality is not supported on Linux because the
VFS will prevent active mounted filesystems from being unmounted,
even with the force option. This is the intended VFS behavior.
Test cases were added to verify the expected behavior based on
the platform.
Discussed-with: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
External-issue: https://reviews.freebsd.org/D22306Closes#9904
Tests that get killed do not have an opportunity to clean up.
There are many bad states this can leave the system in, but of
particular gravity is when zinject has been used to induce bad
behavior for one or more of the test disks.
Create a failsafe mechanism in test-runner.py that runs a callback
script after every test. The script is common to all tests so all
tests benefit from the protection.
Add an obligatory `zinject -c all` to clear all zinject state after
every test case is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10096
Filesystems allow overlay mounts by default on FreeBSD and Linux.
Respect the native convention by switching the default to overlay=on,
while retaining the option to turn the property off for compatibility
with other operating systems' conventions.
Update documentation and tests accordingly.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10030
Manual trims fall into the category of long-running pool activities
which people might want to wait synchronously for. This change adds
support to 'zpool wait' for waiting for manual trim operations to
complete. It also adds a '-w' flag to 'zpool trim' which can be used to
turn 'zpool trim' into a synchronous operation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10071
All other ksh scripts use /bin/ksh in the shebang.
Make rsend_016_neg consistent with the rest of the suite.
The test also was absent from any runfiles. Add it to common.run.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10051
This test verifies relatime behavior, which is only present on Linux.
Move the test to linux.run
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10046
These tests are unspported on FreeBSD and Linux for lack of pfexec.
Move the privilege tests to sunos.run and remove the platform checks.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10035
We have have made the necessary changes in our module code to expose
zevents through both devd and the zpool events ioctl. Now the tunables
can be exposed and zpool events tests can be enabled on both platforms.
A few minor tweaks to the tests were needed to accommodate the way wc
formats output on FreeBSD.
zed remains to be ported.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10008
This adds support for setting user properties in a
zfs channel program by adding 'zfs.sync.set_prop'
and 'zfs.check.set_prop' to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Contributions-by: Jason King <jason.king@joyent.com>
Signed-off-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9950
Namespaces is a Linux feature not available on other platforms.
Move the user_namespace test out of common.run to linux.run.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9982
This test uses the scsi_debug Linux kernel module.
Move the test to linux.run until we have an alternative to scsi_debug
worked out on FreeBSD.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9984
Add support for bookmark creation and cloning.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
This feature allows copying existing bookmarks using
zfs bookmark fs#target fs#newbookmark
There are some niche use cases for such functionality,
e.g. when using bookmarks as markers for replication progress.
Copying redaction bookmarks produces a normal bookmark that
cannot be used for redacted send (we are not duplicating
the redaction object).
ZCP support for bookmarking (both creation and copying) will be
implemented in a separate patch based on this work.
Overview:
- Terminology:
- source = existing snapshot or bookmark
- new/bmark = new bookmark
- Implement bookmark copying in `dsl_bookmark.c`
- create new bookmark node
- copy source's `zbn_phys` to new's `zbn_phys`
- zero-out redaction object id in copy
- Extend existing bookmark ioctl nvlist schema to accept
bookmarks as sources
- => `dsl_bookmark_create_nvl_validate` is authoritative
- use `dsl_dataset_is_before` check for both snapshot
and bookmark sources
- Adjust CLI
- refactor shortname expansion logic in `zfs_do_bookmark`
- Update man pages
- warn about redaction bookmark handling
- Add test cases
- CLI
- pyyzfs libzfs_core bindings
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
zdb -R :b fails due to the indirect block being compressed,
and the 'b' and 'd' flag not working in tandem when specified.
Fix the flag parsing code and create a zfs test for zdb -R
block display. Also fix the zio flags where the dotted notation
for the vdev portion of DVA (i.e. 0.0:offset:length) fails.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9640Closes#9729
Allow a range of object identifiers to dump with -d. This may
be useful when dumping a large dataset and you want to break
it up into multiple phases, or to resume where a previous scan
left off. Object type selection flags are supported to reduce
the performance overhead of verbosely dumping unwanted objects,
and to reduce the amount of post-processing work needed to
filter out unwanted objects from zdb output.
This change extends existing syntax in a backward-compatible
way. That is, the base case of a range is to specify a single
object identifier to dump. Ranges and object identifiers can
be intermixed as command line parameters.
Usage synopsis:
Object ranges take the form <start>:<end>[:<flags>]
start Starting object number
end Ending object number, or -1 for no upper bound
flags Optional flags to select object types:
A All objects (this is the default)
d ZFS directories
f ZFS files
m SPA space maps
z ZAPs
- Negate effect of next flag
Examples:
# Dump all file objects
zdb -dd tank/fish 0👎f
# Dump all file and directory objects
zdb -dd tank/fish 0👎fd
# Dump all types except file and directory objects
zdb -dd tank/fish 0👎A-f-d
# Dump object IDs in a specific range
zdb -dd tank/fish 1000:2000
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Closes#9832
This mostly involves reworking platform checks to make illumos the
exception (thanks to their unusual way of exposing xattrs). Other
platforms are able to take advantage of the recently added xattr
wrappers in libtest.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9872
This adds support in channel programs to inherit properties analogous
to `zfs inherit` by adding `zfs.sync.inherit` and `zfs.check.inherit`
functions to the ZFS LUA API.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jason King <jason.king@joyent.com>
Closes#9738
As an alternative to the dataset name, zdb now allows the decimal
or hexadecimal objset ID to be specified. When permanent errors
are reported as 2 hexadecimal numbers (objset ID : object ID) in
zpool status; you can now use 'zdb <pool>[/objset ID] object' to
determine the names of the objset and object which have the error.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9733
This commit adds the --saved (-S) to the 'zfs send' command.
This flag allows a user to send a partially received dataset,
which can be useful when migrating a backup server to new
hardware. This flag is compatible with resumable receives, so
even if the saved send is interrupted, it can be resumed.
The flag does not require any user / kernel ABI changes or any
new feature flags in the send stream format.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Reviewed-by: Christian Schwarz <me@cschwarz.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#9007
Neither FreeBSD nor Linux support dumping to zvols.
DilOS still uses these tests, so the files are kept and the tests have
been relocated to sunos.run.
An `is_illumos` function was added to libtest.shlib to eliminate some
awkward platform checks.
A few functions that are not expected to be used outside of illumos
have been sanitized of extraneous FreeBSD adaptations.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9794
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
Additional test cases for the btree implementation, see #9181.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#9717
This interferes with zdb_read_block trying all the decompression
algorithms when the 'd' flag is specified, as some are
expected to fail. Also control the output when guessing
algorithms, try the more common compression types first, allow
specifying lsize/psize, and fix an uninitialized variable.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9612Closes#9630
FreeBSD uses its own crypto framework in-kernel which, at this time,
has no EDONR implementation.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9664
If a device is participating in an active resilver, then it will have a
non-empty DTL. Operations like vdev_{open,reopen,probe}() can cause the
resilver to be restarted (or deferred to be restarted later), which is
unnecessary if the DTL is still covered by the current scan range. This
is similar to the logic in vdev_dtl_should_excise() where the DTL can
only be excised if it's max txg is in the resilvered range.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: John Poduska <jpoduska@datto.com>
Issue #840Closes#9155Closes#9378Closes#9551Closes#9588
The function zdb_read_block (zdb -R) was always intended to have a :c
flag which would read the DVA and length supplied by the user, and
display the checksum. Since we don't know which checksum goes with
the data, we should calculate and display them all.
For each checksum in the table, read in the data at the supplied
DVA:length, calculate the checksum, and display it. Update the man
page and create a zfs test for the new feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9607
Tests that rely on special filesystems that are specific to Linux
should only be run on Linux.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9512
O_TMPFILE is not available on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9503
* Use .ksh extension for ksh scripts, not .sh
* Remove .ksh extension from tests in common.run
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#9502
Tests that aren't limited to running on Linux can be moved to a common
runfile to be shared with other platforms.
The test runner and wrapper script are enhanced to allow specifying
multiple runfiles as a comma-separated list. The default runfiles are
now "common.run,PLATFORM.run" where PLATFORM is determined at run time.
Sections in runfiles that share a path with another runfile can append
a colon separator and an identifier to the path in the section
name, ie `[tests/functional/atime:Linux]`, to avoid overriding the tests
specified by other runfiles.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9391
Allan Jude
Matthew Ahrens
George Wilson
Brian Behlendorf
Robert Novak
George Amanakis
Paul Dagnelie
John Poduska
Sara Hartse
Matthew Ahrens
Matthew Macy
alex
Mariusz Zaborski
Ryan Moeller
Jason King
Christian Schwarz
Paul Zuchowski
Ned Bass
Tom Caputi
Tony Hutter
John Wren Kennedy