The commit b192a2c (Remove avl_size field from struct avl_tree) uses a
def _KERNEL to decide to include avl_pad or not, but this _KERNEL is
defined in sys/sysmacros.h. If avl.h and sysmacros.h are not included
in the right order, it can cause a headache when working on a zfs
related kernel module.
Add sysmacros.h in avl_impl.h to fix. sysmacros.h is also removed
from spa.h as it's reduntant.
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Co-authored-by: Youzhong Yang <yyang@mathworks.com>
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
- Reduce number of allocators on small system down to one per 4
CPU cores, keeping maximum at 4 on 16+ core systems. Small systems
should not have the lock contention multiple allocators supposed
to solve, while having several metaslabs open and modified each
TXG is not free.
- Reduce number of write issue taskqs down to one per 16 CPU
cores and an integer fraction of number of allocators. On mid-
sized systems, where multiple allocators already make sense, too
many write issue taskqs may reduce write speed on single-file
workloads, since single file is handled by only one taskq to
reduce fragmentation. On large systems, that can actually benefit
from many taskq's better IOPS, the bottleneck is less important,
since in worst case there will be at least 16 cores to handle it.
- Distribute dnodes between allocators (and taskqs) in a round-
robin fashion instead of relying on sync taskqs to be balanced.
The last is not guarantied and may depend on scheduling.
- Remove io_wr_iss_tq from struct zio. io_allocator is enough.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#16130
Simplify vdev probes in the zio_vdev_io_done context to
avoid holding the spa config lock for a long duration.
Also allow zpool clear if no evidence of another host
is using the pool.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15839
This commit allow spa_load() to drop the spa_namespace_lock so
that imports can happen concurrently. Prior to dropping the
spa_namespace_lock, the import logic will set the spa_load_thread
value to track the thread which is doing the import.
Consumers of spa_lookup() retain the same behavior by blocking
when either a thread is holding the spa_namespace_lock or the
spa_load_thread value is set. This will ensure that critical
concurrent operations cannot take place while a pool is being
imported.
The zpool command is also enhanced to provide multi-threaded support
when invoking zpool import -a.
Lastly, zinject provides a mechanism to insert artificial delays
when importing a pool and new zfs tests are added to verify parallel
import functionality.
Contributions-by: Don Brady <don.brady@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#16093
Currently, zpool add allows users to add top-level vdevs that have
different ashifts but doing so prevents users from being able to
perform a top-level vdev removal. Often times consumers may not realize
that they have mismatched ashifts until the top-level removal fails.
This feature adds ashift validation to the zpool add command and will
fail the operation if the sector size of the specified vdev does not
match the existing pool. This behavior can be disabled by using the -f
flag. In addition, new flags have been added to provide fine-grained
control to disable specific checks. These flags
are:
--allow-in-use
--allow-ashift-mismatch
--allow-replicaton-mismatch
The force flag will disable all of these checks.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Maybee <mmaybee@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#15509
There exist a couple of macros that are used to update the blkptr birth
times but they can often be confusing. For example, the
BP_PHYSICAL_BIRTH() macro will provide either the physical birth time
if it is set or else return back the logical birth time. The
complement to this macro is BP_SET_BIRTH() which will set the logical
birth time and set the physical birth time if they are not the same.
Consumers may get confused when they are trying to get the physical
birth time and use the BP_PHYSICAL_BIRTH() macro only to find out that
the logical birth time is what is actually returned.
This change cleans up these macros and makes them symmetrical. The same
functionally is preserved but the name is changed. Instead of calling
BP_PHYSICAL_BIRTH(), consumer can now call BP_GET_BIRTH(). In
additional to cleaning up this naming conventions, two new sets of
macros are introduced -- BP_[SET|GET]_LOGICAL_BIRTH() and
BP_[SET|GET]_PHYSICAL_BIRTH. These new macros allow the consumer to
get and set the specific birth time.
As part of the cleanup, the unused GRID macros have been removed and
that portion of the blkptr are currently unused.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#15962
Things get confused when there's more than one name for a thing.
Note that we don't do this for ddt_object_t, ddt_histogram_t and
ddt_stat_t because they're part of the public ZFS interface.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Sponsored-by: Klara, Inc.
Sponsored-by: iXsystems, Inc.
Closes#15887
Detail the import progress of log spacemaps as they can take a very
long time. Also grab the spa_note() messages to, as they provide
insight into what is happening
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Closes#15539
As part of transaction group commit, dsl_pool_sync() sequentially calls
dsl_dataset_sync() for each dirty dataset, which subsequently calls
dmu_objset_sync(). dmu_objset_sync() in turn uses up to 75% of CPU
cores to run sync_dnodes_task() in taskq threads to sync the dirty
dnodes (files).
There are two problems:
1. Each ZVOL in a pool is a separate dataset/objset having a single
dnode. This means the objsets are synchronized serially, which
leads to a bottleneck of ~330K blocks written per second per pool.
2. In the case of multiple dirty dnodes/files on a dataset/objset on a
big system they will be sync'd in parallel taskq threads. However,
it is inefficient to to use 75% of CPU cores of a big system to do
that, because of (a) bottlenecks on a single write issue taskq, and
(b) allocation throttling. In addition, if not for the allocation
throttling sorting write requests by bookmarks (logical address),
writes for different files may reach space allocators interleaved,
leading to unwanted fragmentation.
The solution to both problems is to always sync no more and (if
possible) no fewer dnodes at the same time than there are allocators
the pool.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Edmund Nadolski <edmund.nadolski@ixsystems.com>
Closes#15197
Many long-running ZFS ioctls lock the spa_namespace_lock, forcing
concurrent ioctls to sleep for the mutex. Previously, the only
option is to call mutex_enter() which sleeps uninterruptibly. This
is a usability issue for sysadmins, for example, if the admin runs
`zpool status` while a slow `zpool import` is ongoing, the admin's
shell will be locked in uninterruptible sleep for a long time.
This patch resolves this admin usability issue by introducing
mutex_enter_interruptible() which sleeps interruptibly while waiting
to acquire a lock. It is implemented for both Linux and FreeBSD.
The ZFS_IOC_POOL_CONFIGS ioctl, used by `zpool status`, is changed to
use this new macro so that the command can be interrupted if it is
issued during a concurrent `zpool import` (or other long-running
operation).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Bertschinger <bertschinger@lanl.gov>
Closes#15360
ZFS historically has had several space allocators that were
dynamically selectable. While these have been retained in
OpenZFS, only a single allocator has been statically compiled
in. This patch compiles all allocators for OpenZFS and provides
a module parameter to allow for manual selection between them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ameer Hamza <ahamza@ixsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Edmund Nadolski <edmund.nadolski@ixsystems.com>
Closes#15218
As it turns out having autotrim default to 'on' on FreeBSD never really
worked due to mess with defines where userland and kernel module were
getting different default values (userland was defaulting to 'off',
module was thinking it's 'on').
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#15079
Consistently get the proper default value for autotrim.
Currently, only the kernel module is built with IN_FREEBSD_BASE,
and libzfs get the wrong default value, leading to confusion and
incorrect output when autotrim value was not set explicitly.
Reviewed-by: Warner Losh <imp@bsdimp.com>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#15016
It was a vdev level read cache, designed to aggregate many small
reads by speculatively issuing bigger reads instead and caching
the result. But since it has almost no idea about what is going
on with exception of ZIO_FLAG_DONT_CACHE flag set by higher layers,
it was found to make more harm than good, for which reason it was
disabled for the past 12 years. These days we have much better
instruments to enlarge the I/Os, such as speculative and prescient
prefetches, I/O scheduler, I/O aggregation etc.
Besides just the dead code removal this removes one extra mutex
lock/unlock per write inside vdev_cache_write(), not otherwise
disabled and trying to do some work.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#14953
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
In case check_filesystem() does not error out and does not report
an error, remove that error block from error lists and logs
without requiring a scrub. This can happen when the original file and
all snapshots/clones referencing it have been removed.
Otherwise zpool status will still report that "Permanent errors have
been detected..." without actually reporting any of them.
To implement this change the functions introduced in corrective
receive were modified to take into account the head_errlog feature.
Before this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: Permanent errors have been detected in the following files:
=============================
After this change:
=============================
pool: test
state: ONLINE
status: One or more devices has experienced an unrecoverable error. An
attempt was made to correct the error. Applications are
unaffected.
action: Determine if the device needs to be replaced, and clear the
errors
using 'zpool clear' or replace the device with 'zpool replace'.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-9P
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
/home/user/vdev_a ONLINE 0 0 2
errors: No known data errors
=============================
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14813
At our site we have seen cases when multi-modifier protection is enabled
(multihost=on) on our pool and the pool gets suspended due to a single
disk that is failing and responding very slowly. Our pools have 90 disks
in them and we expect disks to fail. The current version of MMP requires
that we wait for other writers before moving on. When a disk is
responding very slowly, we observed that waiting here was bad enough to
cause the pool to suspend. This change allows the MMP thread to bypass
waiting for other threads and reduces the chances the pool gets
suspended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Herb Wartens <hawartens@gmail.com>
Closes#14659
Spare vdev should detach from the pool when a disk is reinserted.
However, spare detachment depends on the completion of resilvering,
and if resilver does not schedule, the spare vdev keeps attached to
the pool until the next resilvering. When a zfs pool contains
several disks (25+ mirror), resilvering does not always happen when
a disk is reinserted. In this patch, spare vdev is manually detached
from the pool when resilvering does not occur and it has been tested
on both Linux and FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14722
Address the following bugs in persistent error log:
1) Check nested clones, eg "fs->snap->clone->snap2->clone2".
2) When deleting files containing error blocks in those clones (from
"clone" the example above), do not break the check chain.
3) When deleting files in the originating fs before syncing the errlog
to disk, do not break the check chain. This happens because at the
time of introducing the error block in the error list, we do not have
its birth txg and the head filesystem. If the original file is
deleted before the error list is synced to the error log (which is
when we actually lookup the birth txg and the head filesystem), then
we do not have access to this info anymore and break the check chain.
The most prominent change is related to achieving (3). We expand the
spa_error_entry_t structure to accommodate the newly introduced
zbookmark_err_phys_t structure (containing the birth txg of the error
block).Due to compatibility reasons we cannot remove the
zbookmark_phys_t structure and we also need to place the new structure
after se_avl, so it is not accounted for in avl_find(). Then we modify
spa_log_error() to also provide the birth txg of the error block. With
these changes in place we simplify the previously introduced function
get_head_and_birth_txg() (now named get_head_ds()).
We chose not to follow the same approach for the head filesystem (thus
completely removing get_head_ds()) to avoid introducing new lock
contentions.
The stack sizes of nested functions (as measured by checkstack.pl in the
linux kernel) are:
check_filesystem [zfs]: 272 (was 912)
check_clones [zfs]: 64
We also introduced two new tests covering the above changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#14633
Clang's static analyzer pointed out that if we can pass a -1 array index
to copyname[copies] if there are no valid DVAs. This is an absurd
situation, but it suggests that we are missing an assertion, so we add
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14575
Apply zero padding for checksums consistently. The SNPRINTF_BLKPTR
macro was not updated in commit ac7648179c which results in the
`cli_root/zdb/zdb_checksum.ksh` test case reliably failing.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Akash B <akash-b@hpe.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#14497
There is a lock order inversion deadlock between `spa_errlog_lock` and
`dp_config_rwlock`:
A thread in `spa_delete_dataset_errlog()` is running from a sync task.
It is holding the `dp_config_rwlock` for writer (see
`dsl_sync_task_sync()`), and waiting for the `spa_errlog_lock`.
A thread in `dsl_pool_config_enter()` is holding the `spa_errlog_lock`
(see `spa_get_errlog_size()`) and waiting for the `dp_config_rwlock` (as
reader).
Note that this was introduced by #12812.
This commit address this by defining the lock ordering to be
dp_config_rwlock first, then spa_errlog_lock / spa_errlist_lock.
spa_get_errlog() and spa_get_errlog_size() can acquire the locks in this
order, and then process_error_block() and get_head_and_birth_txg() can
verify that the dp_config_rwlock is already held.
Additionally, a buffer overrun in `spa_get_errlog()` is corrected. Many
code paths didn't check if `*count` got to zero, instead continuing to
overwrite past the beginning of the userspace buffer at `uaddr`.
Tested by having some errors in the pool (via `zinject -t data
/path/to/file`), one thread running `zpool iostat 0.001`, and another
thread runs `zfs destroy` (in a loop, although it hits the first time).
This reproduces the problem easily without the fix, and works with the
fix.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14239Closes#14289
`snprintf()` is meant to protect against buffer overflows, but operating
on the buffer using its return value, possibly by calling it again, can
cause a buffer overflow, because it will return how many characters it
would have written if it had enough space even when it did not. In a
number of places, we repeatedly call snprintf() by successively
incrementing a buffer offset and decrementing a buffer length, by its
return value. This is a potentially unsafe usage of `snprintf()`
whenever the buffer length is reached. CodeQL complained about this.
To fix this, we introduce `kmem_scnprintf()`, which will return 0 when
the buffer is zero or the number of written characters, minus 1 to
exclude the NULL character, when the buffer was too small. In all other
cases, it behaves like snprintf(). The name is inspired by the Linux and
XNU kernels' `scnprintf()`. The implementation was written before I
thought to look at `scnprintf()` and had a good name for it, but it
turned out to have identical semantics to the Linux kernel version.
That lead to the name, `kmem_scnprintf()`.
CodeQL only catches this issue in loops, so repeated use of snprintf()
outside of a loop was not caught. As a result, a thorough audit of the
codebase was done to examine all instances of `snprintf()` usage for
potential problems and a few were caught. Fixes for them are included in
this patch.
Unfortunately, ZED is one of the places where `snprintf()` is
potentially used incorrectly. Since using `kmem_scnprintf()` in it would
require changing how it is linked, we modify its usage to make it safe,
no matter what buffer length is used. In addition, there was a bug in
the use of the return value where the NULL format character was not
being written by pwrite(). That has been fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14098
Various module parameters such as `zfs_arc_max` were originally
`uint64_t` on OpenSolaris/Illumos, but were changed to `unsigned long`
for Linux compatibility because Linux's kernel default module parameter
implementation did not support 64-bit types on 32-bit platforms. This
caused problems when porting OpenZFS to Windows because its LLP64 memory
model made `unsigned long` a 32-bit type on 64-bit, which created the
undesireable situation that parameters that should accept 64-bit values
could not on 64-bit Windows.
Upon inspection, it turns out that the Linux kernel module parameter
interface is extensible, such that we are allowed to define our own
types. Rather than maintaining the original type change via hacks to to
continue shrinking module parameters on 32-bit Linux, we implement
support for 64-bit module parameters on Linux.
After doing a review of all 64-bit kernel parameters (found via the man
page and also proposed changes by Andrew Innes), the kernel module
parameters fell into a few groups:
Parameters that were originally 64-bit on Illumos:
* dbuf_cache_max_bytes
* dbuf_metadata_cache_max_bytes
* l2arc_feed_min_ms
* l2arc_feed_secs
* l2arc_headroom
* l2arc_headroom_boost
* l2arc_write_boost
* l2arc_write_max
* metaslab_aliquot
* metaslab_force_ganging
* zfetch_array_rd_sz
* zfs_arc_max
* zfs_arc_meta_limit
* zfs_arc_meta_min
* zfs_arc_min
* zfs_async_block_max_blocks
* zfs_condense_max_obsolete_bytes
* zfs_condense_min_mapping_bytes
* zfs_deadman_checktime_ms
* zfs_deadman_synctime_ms
* zfs_initialize_chunk_size
* zfs_initialize_value
* zfs_lua_max_instrlimit
* zfs_lua_max_memlimit
* zil_slog_bulk
Parameters that were originally 32-bit on Illumos:
* zfs_per_txg_dirty_frees_percent
Parameters that were originally `ssize_t` on Illumos:
* zfs_immediate_write_sz
Note that `ssize_t` is `int32_t` on 32-bit and `int64_t` on 64-bit. It
has been upgraded to 64-bit.
Parameters that were `long`/`unsigned long` because of Linux/FreeBSD
influence:
* l2arc_rebuild_blocks_min_l2size
* zfs_key_max_salt_uses
* zfs_max_log_walking
* zfs_max_logsm_summary_length
* zfs_metaslab_max_size_cache_sec
* zfs_min_metaslabs_to_flush
* zfs_multihost_interval
* zfs_unflushed_log_block_max
* zfs_unflushed_log_block_min
* zfs_unflushed_log_block_pct
* zfs_unflushed_max_mem_amt
* zfs_unflushed_max_mem_ppm
New parameters that do not exist in Illumos:
* l2arc_trim_ahead
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_arc_sys_free
* zfs_deadman_ziotime_ms
* zfs_delete_blocks
* zfs_history_output_max
* zfs_livelist_max_entries
* zfs_max_async_dedup_frees
* zfs_max_nvlist_src_size
* zfs_rebuild_max_segment
* zfs_rebuild_vdev_limit
* zfs_unflushed_log_txg_max
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
* zfs_vnops_read_chunk_size
* zvol_max_discard_blocks
Rather than clutter the lists with commentary, the module parameters
that need comments are repeated below.
A few parameters were defined in Linux/FreeBSD specific code, where the
use of ulong/long is not an issue for portability, so we leave them
alone:
* zfs_delete_blocks
* zfs_key_max_salt_uses
* zvol_max_discard_blocks
The documentation for a few parameters was found to be incorrect:
* zfs_deadman_checktime_ms - incorrectly documented as int
* zfs_delete_blocks - not documented as Linux only
* zfs_history_output_max - incorrectly documented as int
* zfs_vnops_read_chunk_size - incorrectly documented as long
* zvol_max_discard_blocks - incorrectly documented as ulong
The documentation for these has been fixed, alongside the changes to
document the switch to fixed width types.
In addition, several kernel module parameters were percentages or held
ashift values, so being 64-bit never made sense for them. They have been
downgraded to 32-bit:
* vdev_file_logical_ashift
* vdev_file_physical_ashift
* zfs_arc_dnode_limit_percent
* zfs_arc_dnode_reduce_percent
* zfs_arc_meta_limit_percent
* zfs_per_txg_dirty_frees_percent
* zfs_unflushed_log_block_pct
* zfs_vdev_max_auto_ashift
* zfs_vdev_min_auto_ashift
Of special note are `zfs_vdev_max_auto_ashift` and
`zfs_vdev_min_auto_ashift`, which were already defined as `uint64_t`,
and passed to the kernel as `ulong`. This is inherently buggy on big
endian 32-bit Linux, since the values would not be written to the
correct locations. 32-bit FreeBSD was unaffected because its sysctl code
correctly treated this as a `uint64_t`.
Lastly, a code comment suggests that `zfs_arc_sys_free` is
Linux-specific, but there is nothing to indicate to me that it is
Linux-specific. Nothing was done about that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Original-patch-by: Andrew Innes <andrew.c12@gmail.com>
Original-patch-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13984Closes#14004
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
In #13871, zfs_vdev_aggregation_limit_non_rotating and
zfs_vdev_aggregation_limit being signed was pointed out as a possible
reason not to eliminate an unnecessary MAX(unsigned, 0) since the
unsigned value was assigned from them.
There is no reason for these module parameters to be signed and upon
inspection, it was found that there are a number of other module
parameters that are signed, but should not be, so we make them unsigned.
Making them unsigned made it clear that some other variables in the code
should also be unsigned, so we also make those unsigned. This prevents
users from setting negative values that could potentially cause bad
behaviors. It also makes the code slightly easier to understand.
Mostly module parameters that deal with timeouts, limits, bitshifts and
percentages are made unsigned by this. Any that are boolean are left
signed, since whether booleans should be considered signed or unsigned
does not matter.
Making zfs_arc_lotsfree_percent unsigned caused a
`zfs_arc_lotsfree_percent >= 0` check to become redundant, so it was
removed. Removing the check was also necessary to prevent a compiler
error from -Werror=type-limits.
Several end of line comments had to be moved to their own lines because
replacing int with uint_t caused us to exceed the 80 character limit
enforced by cstyle.pl.
The following were kept signed because they are passed to
taskq_create(), which expects signed values and modifying the
OpenSolaris/Illumos DDI is out of scope of this patch:
* metaslab_load_pct
* zfs_sync_taskq_batch_pct
* zfs_zil_clean_taskq_nthr_pct
* zfs_zil_clean_taskq_minalloc
* zfs_zil_clean_taskq_maxalloc
* zfs_arc_prune_task_threads
Also, negative values in those parameters was found to be harmless.
The following were left signed because either negative values make
sense, or more analysis was needed to determine whether negative values
should be disallowed:
* zfs_metaslab_switch_threshold
* zfs_pd_bytes_max
* zfs_livelist_min_percent_shared
zfs_multihost_history was made static to be consistent with other
parameters.
A number of module parameters were marked as signed, but in reality
referenced unsigned variables. upgrade_errlog_limit is one of the
numerous examples. In the case of zfs_vdev_async_read_max_active, it was
already uint32_t, but zdb had an extern int declaration for it.
Interestingly, the documentation in zfs.4 was right for
upgrade_errlog_limit despite the module parameter being wrongly marked,
while the documentation for zfs_vdev_async_read_max_active (and friends)
was wrong. It was also wrong for zstd_abort_size, which was unsigned,
but was documented as signed.
Also, the documentation in zfs.4 incorrectly described the following
parameters as ulong when they were int:
* zfs_arc_meta_adjust_restarts
* zfs_override_estimate_recordsize
They are now uint_t as of this patch and thus the man page has been
updated to describe them as uint.
dbuf_state_index was left alone since it does nothing and perhaps should
be removed in another patch.
If any module parameters were missed, they were not found by `grep -r
'ZFS_MODULE_PARAM' | grep ', INT'`. I did find a few that grep missed,
but only because they were in files that had hits.
This patch intentionally did not attempt to address whether some of
these module parameters should be elevated to 64-bit parameters, because
the length of a long on 32-bit is 32-bit.
Lastly, it was pointed out during review that uint_t is a better match
for these variables than uint32_t because FreeBSD kernel parameter
definitions are designed for uint_t, whose bit width can change in
future memory models. As a result, we change the existing parameters
that are uint32_t to use uint_t.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13875
This type of recv is used to heal corrupted data when a replica
of the data already exists (in the form of a send file for example).
With the provided send stream, corrective receive will read from
disk blocks described by the WRITE records. When any of the reads
come back with ECKSUM we use the data from the corresponding WRITE
record to rewrite the corrupted block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Alek Pinchuk <apinchuk@axcient.com>
Closes#9372
There are times when end-users may wish to have
a fast and convenient method to get zpool guid
without having to use libzfs. This commit
exposes the zpool guid via kstats in similar
manner to the zpool state.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13466
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
The l2cache device could be added twice because vdev_inuse() does not
check spa_l2cache for added devices. Make l2cache vdevs inuse checking
logic more closer to spare vdevs.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9153Closes#12689
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
In all places except two spa_get_random() is used for small values,
and the consumers do not require well seeded high quality values.
Switch those two exceptions directly to random_get_pseudo_bytes()
and optimize spa_get_random(), renaming it to random_in_range(),
since it is not related to SPA or ZFS in general.
On FreeBSD directly map random_in_range() to new prng32_bounded() KPI
added in FreeBSD 13. On Linux and in user-space just reduce the type
used to uint32_t to avoid more expensive 64bit division.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12183
This mostly reverts "3537 want pool io kstats" commit of 8 years ago.
From one side this code using pool-wide locks became pretty bad for
performance, creating significant lock contention in I/O pipeline.
From another, there are more efficient ways now to obtain detailed
statistics, while this statistics is illumos-specific and much less
usable on Linux and FreeBSD, reported only via procfs/sysctls.
This commit does not remove KSTAT_TYPE_IO implementation, that may
be removed later together with already unused KSTAT_TYPE_INTR and
KSTAT_TYPE_TIMER.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12212
These are used by userspace, so should live in a public header
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12116
For gang blocks, `DVA_GET_ASIZE()` is the total space allocated for the
gang DVA including its children BP's. The space allocated at each DVA's
vdev/offset is `vdev_psize_to_asize(vd, SPA_GANGBLOCKSIZE)`.
This commit makes this relationship more clear by using a helper
function, `vdev_gang_header_asize()`, for the space allocated at the
gang block's vdev/offset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11744
Fix regression seen in issue #11545 where checksum errors
where not being counted or showing up in a zpool event.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11609
Mixing ZIL and normal allocations has several problems:
1. The ZIL allocations are allocated, written to disk, and then a few
seconds later freed. This leaves behind holes (free segments) where the
ZIL blocks used to be, which increases fragmentation, which negatively
impacts performance.
2. When under moderate load, ZIL allocations are of 128KB. If the pool
is fairly fragmented, there may not be many free chunks of that size.
This causes ZFS to load more metaslabs to locate free segments of 128KB
or more. The loading happens synchronously (from zil_commit()), and can
take around a second even if the metaslab's spacemap is cached in the
ARC. All concurrent synchronous operations on this filesystem must wait
while the metaslab is loading. This can cause a significant performance
impact.
3. If the pool is very fragmented, there may be zero free chunks of
128KB or more. In this case, the ZIL falls back to txg_wait_synced(),
which has an enormous performance impact.
These problems can be eliminated by using a dedicated log device
("slog"), even one with the same performance characteristics as the
normal devices.
This change sets aside one metaslab from each top-level vdev that is
preferentially used for ZIL allocations (vdev_log_mg,
spa_embedded_log_class). From an allocation perspective, this is
similar to having a dedicated log device, and it eliminates the
above-mentioned performance problems.
Log (ZIL) blocks can be allocated from the following locations. Each
one is tried in order until the allocation succeeds:
1. dedicated log vdevs, aka "slog" (spa_log_class)
2. embedded slog metaslabs (spa_embedded_log_class)
3. other metaslabs in normal vdevs (spa_normal_class)
The space required for the embedded slog metaslabs is usually between
0.5% and 1.0% of the pool, and comes out of the existing 3.2% of "slop"
space that is not available for user data.
On an all-ssd system with 4TB storage, 87% fragmentation, 60% capacity,
and recordsize=8k, testing shows a ~50% performance increase on random
8k sync writes. On even more fragmented systems (which hit problem #3
above and call txg_wait_synced()), the performance improvement can be
arbitrarily large (>100x).
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11389
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
Duplicate io and checksum ereport events can misrepresent that
things are worse than they seem. Ideally the zpool events and the
corresponding vdev stat error counts in a zpool status should be
for unique errors -- not the same error being counted over and over.
This can be demonstrated in a simple example. With a single bad
block in a datafile and just 5 reads of the file we end up with a
degraded vdev, even though there is only one unique error in the pool.
The proposed solution to the above issue, is to eliminate duplicates
when posting events and when updating vdev error stats. We now save
recent error events of interest when posting events so that we can
easily check for duplicates when posting an error.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10861
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
In FreeBSD trim has defaulted to on for several
years. In order to minimize POLA violations on
import it's important to maintain this default
when importing vendored openzfs in to FreeBSD
base.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10719
youzhongyang
Alexander Motin
Don Brady
George Wilson
Rob Norris
ednadolski-ix
Thomas Bertschinger
Yuri Pankov
Brian Behlendorf
George Amanakis
Herb Wartens
Ameer Hamza
Richard Yao
Matthew Ahrens
Alek P
Tino Reichardt
наб
Andrew
Jorgen Lundman
Allan Jude
Fedor Uporov
Matthew Ahrens
Ryan Moeller
Michael Niewöhner
Matthew Macy