Document the ZFS_DKMS_ENABLE_DEBUGINFO option in the userland
configuration file, as done with the other ZFS_DKMS_* options.
It has been introduced with commit e45c1734a6 ("dkms: Enable
debuginfo option to be set with zfs sysconfig file") but isn't
mentioned anywhere other than the 'dkms.conf' file (generated).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Closes#9191
$fs used with the wrong sed command where should be $mntpnt instead
to match a variable exported by read_mtab()
The fix is mostly to reuse the sed command found in read_mtab()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Alexey Smirnoff <fling@member.fsf.org>
Closes#9168
* contrib/initramfs: include /etc/default/zfs and /etc/zfs/zfs-functions
At least debian needs /etc/default/zfs and /etc/zfs/zfs-functions for
its initramfs. Include both in build when initramfs is configured.
* contrib/initramfs: include 60-zvol.rules and zvol_id
Include 60-zvol.rules and zvol_id and set udev as predependency instead
of debians zdev. This makes debians additional zdev hook unneeded.
* Correct initconfdir substitution for some distros
Not every Linux distro is using @sysconfdir@/default but @initconfdir@
which is already determined by configure. Let's use it.
* systemd: prevent possible conflict between systemd and sysvinit
Systemd will not load a sysvinit service if a unit exists with the same
name. This prevents conflicts between sysvinit and systemd.
In ZFS there is one sysvinit service that does not have a systemd
service but a target counterpart, zfs-import.target.
Usually it does not make any sense to install both but it is possisble.
Let's prevent any conflict by masking zfs-import.service by default.
This does not harm even if init.d/zfs-import does not exist.
Reviewed-by: Chris Wedgwood <cw@f00f.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tested-by: Alex Ingram <reimu@reimuhakurei.net>
Tested-by: Dreamcat4 <dreamcat4@gmail.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#7904Closes#9089
When a system boots the zfs-mount.service and the
zfs-share.service can start simultaneously. What may be
unclear is that sharing a filesystem will first mount
the filesystem if it's not already mounted. This means
that both service can race to mount the same fileystem.
This race can result in a SEGFAULT or EBUSY conditions.
This change explicitly defines the start ordering between the
two services such that the zfs-mount.service is solely
responsible for mounting filesystems eliminating the race
between "zfs mount -a" and "zfs share -a" commands.
Reviewed-by: Sebastien Roy <sebastien.roy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <george.wilson@delphix.com>
Closes#9083
The zfs-volume-wait.service scans existing zvols and waits for their
links under /dev to be created. Any service that depends on zvol
links to be there should add a dependency on zfs-volumes.target.
By default, this target is not enabled.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Antonio Russo <antonio.e.russo@gmail.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Zakharov <pzakharov@delphix.com>
Closes#8975
Modify zfs-mount-generator to produce a dependency on new
zfs-import-key-*.service units, dynamically created at boot to call
zfs load-key for the encryption root, before attempting to mount any
encrypted datasets.
These units are created by zfs-mount-generator, and RequiresMountsFor on
the keyfile, if present, or call systemd-ask-password if a passphrase is
requested.
This patch includes suggestions from @Fabian-Gruenbichler, @ryanjaeb and
@rlaager, as well an adaptation of @rlaager's script to retry on
incorrect password entry.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#8750Closes#8848
Alternative implementation of @rlaager's original modification
of zfs-mount-generator fix, with @chrisrd's comments. Set
IFS to be only the tab character, matching our `-H` call in
`zfs list`, allowing spaces to appear in dataset names (and
mountpoints).
Also adds comments explaining our rationale.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#8708Closes#8718
Dracut depends on the environment variable BOOTFS to be set after pool
import. This dracut specific systemd ExecStartPost command should not be
called for any non-dracut systems, so let's move it to a static systemd
unit that.
Reviewed-by: Manuel Amador (Rudd-O) <rudd-o@rudd-o.com>
Reviewed-by: Matthew Thode <prometheanfire@gentoo.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#8510
On debian, systemd complains about missing /bin/awk because it
actually is located at /usr/bin/awk. It is not a good idea to
hardcode binary paths because different linux distros use different
paths. According to systemd's man page it is absolutely safe to
miss paths for binaries located at standard locations (/bin,
/sbin, /usr/bin, ...).
Further, replace this more or less complicated awk command by
grep.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Issue #8510
zfs-import-* services have a hard dependency on bash while not
everyone has bash installed. At this point /bin/sh is sufficient,
so use that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Issue #8510
zfs-import must be done before swap in order for swap on zvol to work
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
Closes#8502
ZFS NFS shares mounted on a client with NFSv3 and with open
locks will fail to reclaim those locks after a server reboot.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8398
Add an 'enclosure_symlinks' option to vdev_id.conf. This creates
consistently named symlinks to the enclosure devices (/dev/sg*) based
off the configuration in vdev_id.conf. The enclosure symlinks show
up in /dev/by-enclosure/<prefix>-<channel><num>. The links make it
make it easy to run sg_ses on a particular enclosure device. The
enclosure links are created in addition to the normal
/dev/disk/by-vdev links.
'enclosure_symlinks' is only valid in sas_direct configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Simon Guest <simon.guest@tesujimath.org>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8194
The 'while read line; ...; done' loop is run in a piped subshell
therefore the 'return 0' would not cause a return from the
is_mounted() function. In all cases, this function will
always return 1.
The fix is to 'return 1' from the subshell on a successful match
(no match == return 0), and then negating the final return value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: TerraTech <TerraTech@users.noreply.github.com>
Closes#8151
This patch collects some minor inconsistencies and typos in the
documentation, logging and testing infrastructure.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7608
lib/libzfs/libzfs_mount.c:zfs_add_options provides the canonical
mount options used by a `zfs mount` command. Because we cannot call
`zfs mount` directly from a systemd.mount unit, we mirror that logic
in zfs-mount-generator.
The zed script is updated to cache these properties as well.
Include a mini-tutorial in the manual page, properly substitute
configuration paths in zfs-mount-generator.8.in, and standardize the
Makefile.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7453
zfs-mount-generator implements the "systemd generator" protocol,
producing systemd.mount units from the cached outputs of zfs list,
during early boot, integrating with systemd.
Each pool has an indpendent cache of the command
zfs list -H -oname,mountpoint,canmount -tfilesystem -r $pool
which is kept synchronized by the ZEDLET
history_event-zfs-list-cacher.sh
Datasets not in the cache will be loaded later in the boot process by
zfs-mount.service, including pools without a cache.
Among other things, this allows for complex mount hierarchies.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#7329
This fixes zfs-mount initscript trying to mount swap volumes
as filesystems or anything that has 'none' as a mountpoint
in /etc/fstab. Additionally, fixes trying to mount swap volumes
as a filesystem on RHEL. RHEL defines mountpoint for swap
as `swap`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Georgy Yakovlev <ya@sysdump.net>
Closes#7346Closes#7347
Clear executable bit on zfs-import.in, zfs-mount.in,
zfs-share.in, and zfs-zed.in. These are automake files and
should not be marked executable. This fixes a RPM build error
on Fedora 28.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7355Closes#7327
Historically a dynamic misc minor number was registered for the
/dev/zfs device in order to prevent minor number collisions. This
was fine but it prevented us from being able to use the kernel
module auto-loaded which requires a known reserved value.
Resolve this issue by adding a configure test to find an available
misc minor number which can then be used in MODULE_ALIAS_MISCDEV at
build time. By adding this alias the zfs kmod is added to the list
of known static-nodes and the systemd-tmpfiles-setup-dev service
will create a /dev/zfs character device at boot time.
This in turn allows us to update the 90-zfs.rules file to make it
aware this is a static node. The upshot of this is that whenever
a process (zpool, zfs, zed) opens the /dev/zfs the kmods will be
automatic loaded. This even works for unprivileged users so there
is no longer a need to manually load the modules at boot time.
As an additional bonus the zed now no longer needs to start after
the zfs-import.service since it will trigger the module load.
In the unlikely event the minor number we selected conflicts with
another out of tree unregistered minor number the code falls back
to dynamically allocating it. In this case the modules again
must be manually loaded.
Note that due to the change in the method of registering the minor
number the zimport.sh test case may incorrectly fail when the
static node for the installed packages is created instead of the
dynamic one. This issue will only transiently impact zimport.sh
for this single commit when we transition and are mixing and
matching methods.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
TEST_ZIMPORT_SKIP="yes"
Closes#7287
This allows for systems with zfs built into the kernel manually to run
these services. Otherwise the service will fail to start.
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Thode <mthode@mthode.org>
Closes#7174
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Use the same method used in zfs-load-key.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Llewelyn Trahaearn <WoefulDerelict@GMail.com>
Signed-off-by: Matthew Thode <mthode@mthode.org>
Closes#7089
'zfs load-key -a' will only be called if needed. If a dataset not
needed for boot does not have its key loaded (home directories for
example) boot can still continue.
zfs:AUTO was not working via dracut, so we still need the generator
script to do its thing.
Reviewed-by: Richard Yao <ryao@gentoo.org>
Reviewed-by: Manuel Amador (Rudd-O) <rudd-o@rudd-o.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Matthew Thode <mthode@mthode.org>
Closes#6982Closes#7004
Some redundancy is present in the systemd dependencies, as
noticed in PR#6764. Existing setups might rely on these quirks,
so these cleanups have been moved to the development branch.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#6822
zfs-import-{cache,scan}.service must complete before any mounting of
filesystems can occur. To simplify this dependency, create a target
that is reached After (in the systemd sense) the pool is imported.
Additionally, recommend that legacy zfs mounts use the option
x-systemd.requires=zfs-import.target
to codify this requirement.
Reviewed-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#6764
On systems with SCSI rather than SAS disk topology, this change enables
the vdev_id script to match against the block device path, and therefore
create a vdev alias in /dev/disk/by-vdev.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Simon Guest <simon.guest@tesujimath.org>
Closes#6592
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Signed-off-by: Fabian Grünbichler <f.gruenbichler@proxmox.com>
Closes#6599
By default the mount(8) command, as invoked by 'zfs mount', will try
to resolve any path parameter in its canonical form: this could lead
to mount failures when the cwd contains a symlink having the same name
of the dataset being mounted.
Fix this by explicitly disabling mount(8) path canonicalization.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#1791Closes#6429Closes#6437
Using /sbin/runscript is deprecated and throws a QA warning
when still used in init scripts.
Reviewed-by: bunder2015 <omfgbunder@gmail.com>
Signed-off-by: BtbN <btbn@btbn.de>
Closes#6519
Users can now provide their own scripts to be run
with 'zpool iostat/status -c'. User scripts should be
placed in ~/.zpool.d to be included in zpool's
default search path.
Provide a script which can be used with
'zpool iostat|status -c' that will return the type of
device (hdd, sdd, file).
Provide a script to get various values from smartctl
when using 'zpool iostat/status -c'.
Allow users to define the ZPOOL_SCRIPTS_PATH
environment variable which can be used to override
the default 'zpool iostat/status -c' search path.
Allow the ZPOOL_SCRIPTS_ENABLED environment
variable to enable or disable 'zpool status/iostat -c'
functionality.
Use the new smart script to provide the serial command.
Install /etc/sudoers.d/zfs file which contains the sudoer
rule for smartctl as a sample.
Allow 'zpool iostat/status -c' tests to run in tree.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6121Closes#6153
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Background information: This assertion about tx_space_* verifies that we
are not dirtying more stuff than we thought we would. We “need” to know
how much we will dirty so that we can check if we should fail this
transaction with ENOSPC/EDQUOT, in dmu_tx_assign(). While the
transaction is open (i.e. between dmu_tx_assign() and dmu_tx_commit() —
typically less than a millisecond), we call dbuf_dirty() on the exact
blocks that will be modified. Once this happens, the temporary
accounting in tx_space_* is unnecessary, because we know exactly what
blocks are newly dirtied; we call dnode_willuse_space() to track this
more exact accounting.
The fundamental problem causing this bug is that dmu_tx_hold_*() relies
on the current state in the DMU (e.g. dn_nlevels) to predict how much
will be dirtied by this transaction, but this state can change before we
actually perform the transaction (i.e. call dbuf_dirty()).
This bug will be fixed by removing the assertion that the tx_space_*
accounting is perfectly accurate (i.e. we never dirty more than was
predicted by dmu_tx_hold_*()). By removing the requirement that this
accounting be perfectly accurate, we can also vastly simplify it, e.g.
removing most of the logic in dmu_tx_count_*().
The new tx space accounting will be very approximate, and may be more or
less than what is actually dirtied. It will still be used to determine
if this transaction will put us over quota. Transactions that are marked
by dmu_tx_mark_netfree() will be excepted from this check. We won’t make
an attempt to determine how much space will be freed by the transaction
— this was rarely accurate enough to determine if a transaction should
be permitted when we are over quota, which is why dmu_tx_mark_netfree()
was introduced in 2014.
We also won’t attempt to give “credit” when overwriting existing blocks,
if those blocks may be freed. This allows us to remove the
do_free_accounting logic in dbuf_dirty(), and associated routines. This
logic attempted to predict what will be on disk when this txg syncs, to
know if the overwritten block will be freed (i.e. exists, and has no
snapshots).
OpenZFS-issue: https://www.illumos.org/issues/7793
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3704e0a
Upstream bugs: DLPX-32883a
Closes#5804
Porting notes:
- DNODE_SIZE replaced with DNODE_MIN_SIZE in dmu_tx_count_dnode(),
Using the default dnode size would be slightly better.
- DEBUG_DMU_TX wrappers and configure option removed.
- Resolved _by_dnode() conflicts these changes have not yet been
applied to OpenZFS.
The mount(8) command will helpfully try to resolve any device name
which is passed in. It does this by applying some simple heuristics
before passing it along to the registered mount helper.
Normally this fine. However, one of these heuristics is to prepend
the current working directory to the passed device name. If that
resulting directory name exists mount(8) will perform the mount(2)
system call and never invoke the helper utility.
Since the cwd for systemd when running as the system instance is
the root directory the default mount points created by zfs(8) can
cause a mount failure.
This change avoids the issue by explicitly setting the cwd to
a different path when performing the mount.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#5719
Use the system /bin directory rather than the package install
@bindir@. This allows --prefix=/usr/local to work as intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#5559
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Haakan T Johansson <f96hajo@chalmers.se>
Closes#5547Closes#5543
Fix misleading error message:
"The /dev/zfs device is missing and must be created.", if /etc/mtab is missing.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Eric Desrochers <eric.desrochers@canonical.com>
Closes#4680Closes#5029
A lot of string replacement target don't have dependency or incorrect
dependency. We setup proper dependency by pattern rules.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4908
* Disable zfs-import-scan.service by default. This ensures that
pools will not be automatically imported unless they appear in
the cache file. When this service is explicitly enabled pools
will be imported with the "cachefile=none" property set. This
prevents the creation of, or update to, an existing cache file.
$ systemctl list-unit-files | grep zfs
zfs-import-cache.service enabled
zfs-import-scan.service disabled
zfs-mount.service enabled
zfs-share.service enabled
zfs-zed.service enabled
zfs.target enabled
* Change services to dynamic from static by adding an [Install]
section and adding 'WantedBy' tags in favor of 'Requires' tags.
This allows for easier customization of the boot behavior.
* Start the zfs-import-cache.service after the root pivot so
the cache file is available in the standard location.
* Start the zfs-mount.service after the systemd-remount-fs.service
to ensure the root fs is writeable and the ZFS filesystems can
create their mount points.
* Change the default behavior to only load the ZFS kernel modules
in zfs-import-*.service or when blkid(8) detects a pool. Users
who wish to unconditionally load the kernel modules must uncomment
the list of modules in /lib/modules-load.d/zfs.conf.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4325Closes#4496Closes#4658Closes#4699
- In older systems without sysroot.mount, import before dracut-mount,
and re-enable old dracut mount hook
- rootflags MUST be present even if the administrator neglected to
specify it explicitly
- Check that mount.zfs exists in sbindir
- Remove awk and head as (now unused) requirements, add grep, and
install the right mount.zfs
- Eliminate one use of grep in Dracut
- Use a more accurate grepping statement to identify zfsutil in rootflags
- Ensure that pooldev is nonempty
- Properly handle /dev/sd* devices and more
- Use new -P to get list of zpool devices
- Bail out of the generator when zfs:AUTO is on the root command line
- Ignore errors from systemctl trying to load sysroot.mount, we only
care about the output
- Determine which one is the correct initqueuedir at run time.
- Add a compatibility getargbool for our detection / setup script.
- Update dracut .gitignore files
Signed-off-by: <Matthew Thode mthode@mthode.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4558Closes#4562
Both Alpine Linux and Gentoo use OpenRC so we share its logic
Signed-off-by: Carlo Landmeter <clandmeter@gmail.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4386
Debian based systems use nfs-kernel-server as the service name.
List both nfs-server.service and nfs-kernel-server.service so
this service will work on multiple distributions.
Signed-off-by: Grischa Zengel <github.zfsonlinux@zengel.info>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4350
This change modifies the import service to use the default cache file
to perform a verbatim import of pools at boot. This fixes code that
searches all devices and imported all visible pools.
Using the cache file is in keeping with the way ZFS has always worked,
how Solaris, Illumos, FreeBSD, and systemd performs imports, and is how
it is written in the man page (zpool(1M,8)):
All pools in this cache are automatically imported when the
system boots.
Importantly, the cache contains important information for importing
multipath devices, and helps control which pools get imported in more
dynamic environments like SANs, which may have thousands of visible
and constantly changing pools, which the ZFS_POOL_EXCEPTIONS variable
is not equipped to handle. Verbatim imports prevent rogue pools from
being automatically imported and mounted where they shouldn't be.
The change also stops the service from exporting pools at shutdown.
Exporting pools is only meant to be performed explicitly by the
administrator of the system.
The old behavior of searching and importing all visible pools is
preserved and can be switched on by heeding the warning and toggling
the ZPOOL_IMPORT_ALL_VISIBLE variable in /etc/default/zfs.
Signed-off-by: James Lee <jlee@thestaticvoid.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3777Closes#3526
For consistency all systemd unit files and init scripts now share
the same names. This prevents an issue where the zed is started
twice on systems where both the systemd and sysv infrastructure is
installed concurrently.
For backward compatibility a 'zed' alias has been added. This
allows the user to interact with the service using either the
name 'zed' or 'zfs-zed'.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3837
* Fix regression - "OVERLAY_MOUNTS" should have been "DO_OVERLAY_MOUNTS".
* Fix update-rc.d commands in postinst. Thanx to subzero79@GitHub.
* Fix make sure a filesystem exists before trying to mount in mount_fs()
* Fix local variable usage.
* Fix to read_mtab():
* Strip control characters (space - \040) from /proc/mounts GLOBALY,
not just first occurrence.
* Don't replace unprintable characters ([/-. ]) for use in the variable
name with underscore. No need, just remove them all together.
* Add check_boolean() to check if a user configure option is
set ('yes', 'Yes', 'YES' or any combination there of) OR '1'.
Anything else is considered 'unset'.
* Add a ZFS_POOL_IMPORT to the default config.
* This is a semi colon separated list of pools to import ONLY.
* This is intended for systems which have _a lot_ of pools (from
a SAN for example) and it would be to many to put in the
ZFS_POOL_EXCEPTIONS variable..
* Add a config option "ZPOOL_IMPORT_OPTS" for adding additional options
to "zpool import".
* Add documentation and the chance of overriding the ZPOOL_CACHE
variable in the config file.
* Remove "sort" from find_pools() and setup_snapshot_booting().
Sometimes not available, and not really necessary.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Issue #3816
Resolve the following error when restarting the zed by force creating
the /run/sendsigs.omit.d/zed link.
sudo /etc/init.d/zfs-zed restart
* Stopping ZFS Event Daemon [ OK ]
* Starting ZFS Event Daemon
ln: failed to create symbolic link `/run/sendsigs.omit.d/zed': File exists
Signed-off-by: SenH <sen@senhaerens.be>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3747
ZED depends on /var. When /var is a separate dataset, it must be
mounted before starting ZED. This change moves the zfs-zed service
from starting first, to starting after zfs-mount, but before zfs-share.
As discussed in issue #3513, ZED does not need to start first in order
to consume events made during the zfs-import and zfs-mount services.
The events will be queued and can be handled later in the boot process.
ZED may, however, handle sharing in the future, so it should be started
before the zfs-share service.
This commit also stops the zfs-import service from writing temp files
to /var/tmp on shutdown and it corrects the return code for the OpenRC
service.
Other OpenRC-specific changes noted in issue #3513 were reitereated in
issue #3715 and committed in da619f3.
Signed-off-by: James Lee <jlee@thestaticvoid.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3513
The dependencies for handling / on ZFS belong in the mount script, not
the zed script.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3715
This is some minor fixes to commits 2cac7f5f11
and 2a34db1bdb.
* Make sure to alien'ate the new initramfs rpm package as well!
The rpm package is build correctly, but alien isn't run on it to
create the deb.
* Before copying file from COPY_FILE_LIST, make sure the DESTDIR/dir exists.
* Include /lib/udev/vdev_id file in the initrd.
* Because the initrd needs to use '/sbin/modprobe' instead of 'modprobe',
we need to use this in load_module() as well.
* Make sure that load_module() can be used more globaly, instead of
calling '/sbin/modprobe' all over the place.
* Make sure that check_module_loaded() have a parameter - module to
check.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3626
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
This is especially needed when using LUKS backed pools.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3536
* In read_mtab(), fix problems (!?) in the mounts file. It will record
'rpool 1' as 'rpool\0401' instead of 'rpool\00401' which seems to be the
correct (at least as far as 'printf' is concerned). Use this using the
external 'echo' command (and not the one built in to the shell) because
the internal one would interpret the backslash code (incorrectly), giving
us a instead.
* Remove reregister_mounts() - no longer needed.
* For Gentoo, the zfs_log_failure_msg() should use eend(), not eerror()
(which requires an error message, which we don't have).
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3488Closes#3509Closes#3514
This reverts commit 036391c980.
Because #3509 came just after this commit was accepted and is related
to the original problem the commit was supposed to fix, we need to
solve the problem in another way.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Use the 'mount' command instead of /proc/mounts to get a list of matching
filesystems.
This because /proc/mounts reports a pool with a space 'rpool 1' as
'rpool\0401'. The space is encoded as 3-digit octal which is legal.
However 'printf "%b"', which we use to filter out other illegal
characters (such as slash, space etc) can't properly interpret this
because it expects 4-digit octal. We get a instead of the space
we expected. The correct value should have been 'rpool\00401' (note
the additional leading zero).
So use 'mount', which interprets all backslash-escapes correctly,
instead.
Signed-off-by: Turbo Fredriksson turbo@bayour.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3488
* Change the order of the function library check/load.
Redhat based system _can_ have a /lib/lsb/init-functions file (from
the redhat-lsb-core package), but it's only partially what we can use.
Instead, look for that file last, giving the script a chance to catch
the 'real' distribution file.
* Filter out dashes and dots in dataset name in read_mtab().
* Get rid of 'awk' entirely. This is usually in /usr, which might not
be availible.
* Get rid of the 'find /dev/disk/by-*' (find is on /usr, which might not
be availible). Instead use echo in a for loop.
* Rebuild scripts if any of the *.in files changed.
* Move the sed part that filters out duplicates inside the check fo
valid variable.
Signed-off-by: Turbo Fredriksson turbo@bayour.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3463Closes#3457
* Based on the init scripts included with Debian GNU/Linux, then take code
from the already existing ones, trying to merge them into one set of
scripts that will work for 'everyone' for better maintainability.
* Add configurable variables to control the workings of the init scripts:
* ZFS_INITRD_PRE_MOUNTROOT_SLEEP
Set a sleep time before we load the module (used primarily by initrd
scripts to allow for slower media (such as USB devices etc) to be
availible before we load the zfs module).
* ZFS_INITRD_POST_MODPROBE_SLEEP
Set a timed sleep in the initrd to after the load of the zfs module.
* ZFS_INITRD_ADDITIONAL_DATASETS
To allow for mounting additional datasets in the initrd. Primarily used
in initrd scripts to allow for when filesystem needed to boot (such as
/usr, /opt, /var etc) isn't directly under the root dataset.
* ZFS_POOL_EXCEPTIONS
Exclude pools from being imported (in the initrd and/or init scripts).
* ZFS_DKMS_ENABLE_DEBUG, ZFS_DKMS_ENABLE_DEBUG_DMU_TX, ZFS_DKMS_DISABLE_STRIP
Set to control how dkms should build the dkms packages.
* ZPOOL_IMPORT_PATH
Set path(s) where "zpool import" should import pools from.
This was previously the job of "USE_DISK_BY_ID" (which is still used
for backwards compatibility) but was renamed to allow for better
control of import path(s).
* If old USE_DISK_BY_ID is set, but not new ZPOOL_IMPORT_PATH, then we
set ZPOOL_IMPORT_PATH to sane defaults just to be on the safe side.
* ZED_ARGS
To allow for local options to zed without having to change the init script.
* The import function, do_import(), imports pools by name instead of '-a'
for better control of pools to import and from where.
* If USE_DISK_BY_ID is set (for backwards compatibility), but isn't 'yes'
then ignore it.
* If pool(s) isn't found with a simple "zpool import" (seen it happen),
try looking for them in /dev/disk/by-id (if it exists). Any duplicates
(pools found with both commands) is filtered out.
* IF we have found extra pool(s) this way, we must force USE_DISK_BY_ID
so that the first, simple "zpool import $pool" is able to find it.
* Fallback on importing the pool using the cache file (if it exists) only
if 'simple' import (either with ZPOOL_IMPORT_PATH or the 'built in'
defaults) didn't work.
* The export function, do_export(), will export all pools imported, EXCEPT
the root pool (if there is one).
* ZED script from the Debian GNU/Linux packages added.
* Refreshed ZED init script from behlendorf@5e7a660 to be portable so it
may be used on both LSB and Redhat style systems.
* If there is no pool(s) imported and zed successfully shut down, we will
unload the zfs modules.
* The function library file for the ZoL init script is installed as
/etc/init.d/zfs-functions.
* The four init scripts, the /etc/{defaults,sysconfig,conf.d}/zfs config file
as well as the common function library is tagged as '%config(noreplace)' in
the rpm rules file to make sure they are not replaced automatically if locally
modifed.
* Pitfals and workarounds:
* If we're running from init, remove stale /etc/dfs/sharetab before importing
pools in the zfs-import init script.
* On Debian GNU/Linux, there's a 'sendsigs' script that will kill basically
everything quite early in the shutdown phase and zed is/should be stopped
much later than that. We don't want zed to be among the ones killed, so add
the zed pid to list of pids for 'sendsigs' to ignore.
* CentOS uses echo_success() and echo_failure() to print out status of
command. These in turn uses "echo -n \0xx[etc]" to move cursor and choose
colour etc. This doesn't work with the modified IFS variable we need to
use in zfs-import for some reason, so work around that when we define
zfs_log_{end,failure}_msg() for RedHat and derivative distributions.
* All scripts passes ShellCheck (with one false positive in do_mount()).
Signed-off-by: Turbo Fredriksson turbo@bayour.com
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Yao <ryao@gentoo.org>
Reviewed by: Chris Dunlap <cdunlap@llnl.gov>
Closes#2974Closes#2107
Commit 87abfcb broke the systemd import service by treating the
ExecStart line as if it were a shell command that could be executed.
This isn't the way systemd works and the correct way to handle this
case is with ExecStartPre. This patch updates the zfs import service
files accordingly,
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Chris Siebenmann <cks.git01@cs.toronto.edu>
Closes#3440
While module loading itself is synchronous the creation of the /dev/zfs
device is not. This is because /dev/zfs is typically created by a udev
rule after the module is registered and presented to user space through
sysfs. This small window between module loading and device creation
can result in spurious failures of libzfs_init().
This patch closes that race by extending libzfs_init() so it can detect
that the modules are loaded and only if required wait for the /dev/zfs
device to be created. This allows scripts to reliably use the following
shell construct without the need for additional error handling.
$ /sbin/modprobe zfs && /sbin/zpool import -a
To minimize the potential time waiting in libzfs_init() a strategy
similar to adaptive mutexes is employed. The function will busy-wait
for up to 10ms based on the expectation that the modules were just
loaded and therefore the /dev/zfs will be created imminently. If it
takes longer than this it will fall back to polling for up to 10 seconds.
This behavior can be customized to some degree by setting the following
new environment variables. This functionality is provided for backwards
compatibility with existing scripts which depend on the module auto-load
behavior. By default module auto-loading is now disabled.
* ZFS_MODULE_LOADING="YES|yes|ON|on" - Attempt to load modules.
* ZFS_MODULE_TIMEOUT="<seconds>" - Seconds to wait for /dev/zfs
The zfs-import-* systemd service files have been updated to call
'/sbin/modprobe zfs' so they no longer rely on the legacy auto-loading
behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#2556
The resulting script is not removed by 'make clean' or rebuilt
when the source files are changed. Users with long standing git
trees may find their init script is out of date.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3273
This commit updates the zfs.redhat.in script to start/stop ZED.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3153
This commit replaces the zfs.redhat.in init script with a slightly
modified version of the existing zfs.lsb.in init script. This was
done to minimize the functional differences between platforms.
The lsb version of the script was choosen because it's heavily
tested and provides the most functionality.
Changes made for RHEL systems:
* Configuration: /etc/default/zfs -> /etc/sysconfig/zfs
* LSB functions: /lib/lsb/init-functions -> /etc/rc.d/init.d/functions
* Logging: log_begin_msg/log_end_msg -> action
Features in LSB which are now in RHEL:
* USE_DISK_BY_ID=0 - Use the by-id names
* VERBOSE_MOUNT=0 - Verbose mounts by default
* DO_OVERLAY_MOUNTS=0 - Overlay mounts by default
* MOUNT_EXTRA_OPTIONS=0 - Generic extra options
Existing RHEL features which were removed:
* Automatically mounting FSs on ZVOLs listed in /etc/fstab
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #3153
The systemd script zfs-share.service does 'zfs share -a' to share
any required datasets. Unfortunately, /etc/dfs/sharetab is stale
from the previous boot. Delete it before we share.
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2883
The zfs-share.service rule needs to be modified to ensure that it
does not execute before zfs-mount.service.
Signed-off-by: Dan Swartzendruber <dswartz@druber.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ralf Ertzinger <ralf@skytale.net>
Closes#2893
The zfs-import-cache.service and zfs-import-scan.service should
should be started after cryptsetup to ensure all LUKS devices have
been opened.
Signed-off-by: alteriks <alteriks@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1474
Change the startup mode of ZED to non-forking. While systemd can
track processes that detach from the terminal just fine, running
processes in non-forking mode is the preferred mode of operation.
Also remove user/group definitions as root/root is the default.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2252
This commit adds a systemd unit file for zed.service and integrates
it into the zfs.target from commit 881f45c.
Signed-off-by: Chris Dunlap <cdunlap@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2108
Issue #2
p_l in #zfsonlinux reported that he had issues mounting filesystems that
were resolved by adding rc_need="mtab" to /etc/init.d/zfs. Closer
inspection revealed that we do have a race, but it is not clear how this
race caused mounting to fail. What is clear is that this race should be
fixed, so lets add the proper `use mtab` line to handle it.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2148
This adds systemd unit files replacing the functionality offered by
the SysV init script found in etc/init.d.
It has been developed and tested on Fedora 19, Fedora 20
and openSuSE 13.1.
Four unit files and one target are offered.
zfs-import-cache.service:
Import pools from /etc/zfs/zpool.cache. This unit will wait for
udev to settle.
zfs-import-scan.service:
Import pools by scanning /dev/disk/by-id for zvols. This unit will
only run if /etc/zfs/zpool.cache is not present. This unit will wait
for udev to settle
zfs-mount.service:
Mount ZFS native filesystems. It contains a dependency to be loaded
before local-fs.target.
zfs-share.service:
Share NFS/SMB filesystems. This unit contains a dependency that
will cause it to be restarted whenever the smb or nfs-server unit
is restarted, restoring the shares added.
zfs.target:
This target pulls in the other units in order to start ZFS. It's
the only unit that can be enabled/disabled, all other services
are static and pulled in by dependencies. It will honour zfs=off
and zfs=no options on the kernel command line.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2108
The vdev_id udev helper currently applies slot renumbering rules to
every channel (JBOD) in the system. This is too inflexible for systems
with non-homogeneous storage topologies. The "slot" keyword now takes
an optional third parameter which names a channel to which the mapping
will apply. If the third parameter is omitted then the rule applies to
all channels. The first-specified rule that can match a slot takes
precedence. Therefore a channel-specific rule for a given slot should
generally appear before a generic rule for the same slot number. In
this way a custom slot mapping can be applied to a particular channel
and a default mapping applied to the rest.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2056
As a 'stop' action ensure the filesystem is unshared before
it is unmounted, just in case. Additionally, export the pool
so it may be cleanly imported by a different host.
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2003
Allow verbose mounts to make is easier to monitor progress when
mounting a large number of filesystems.
This functionality is disabled by default.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1929
Many people prefer to use by-id at import time instead of using
the cache file. This can be a much better solution than the cache
file in some environments so we're adding some infrastructure to
allow it.
This functionality is disabled by default.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1929
The previous pattern could accidentally match on things like
'real_root=ZFS=node02-zp00/ROOT/rootfs' due to the 'ZFS=no'
substring.
Signed-off-by: Matthew Thode <mthode@mthode.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1837
The current zfs OpenRC script's dependencies cause OpenRC to attempt to
unmount ZFS filesystems at shutdown while things were still using them,
which would fail. This is a cosmetic issue, but it should still be
addressed. It probably does not affect systems where the rootfs is a
legacy filesystem, but any system with the rootfs on ZFS needs to run
the ZFS init script after the system is ready to shutdown filesystems.
OpenRC's shutdown process occurs in the reverse order of the startup
process. Therefore running the ZFS shutdown procedure after filesystems
are ready to be unmounted requires running the startup procedure before
fstab. This patch changes the dependencies of the script to expliclty
run before fstab at boot when the rootfs is ZFS and to run after fstab
at boot whenever the rootfs is not ZFS. This should cover most use
cases.
The only cases not covered well by this are systems with legacy
root filesystems where people want to configure fstab to mount a non-ZFS
filesystem off a zvol and possibly also systems whose pools are stored
on network block devices. The former requires that the ZFS script run
before fstab, which could cause ZFS datasets to mount too early and
appear under the fstab mount points. The latter requires that the ZFS
script run after networking starts, which precludes the ability to store
any system information on ZFS. An additional OpenRC script could be
written to handle non-root pools on network block devices, but that will
depend on user demand and developer time.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1479
The kernel modules are now available in the Arch User Repository
(AUR) via zfs. Since their packaging is maintained and superior
to ours it is being removed from the tree.
https://wiki.archlinux.org/index.php/ZFS
Now that various distributions are picking up the packages we
should eventually be able to remove most of this infrastructure.
Packaging belongs with the distributions not upstream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
In the interest of maintaining only one udev helper to give vdevs
user friendly names, the zpool_id and zpool_layout infrastructure
is being retired. They are superseded by vdev_id which incorporates
all the previous functionality.
Documentation for the new vdev_id(8) helper and its configuration
file, vdev_id.conf(5), can be found in their respective man pages.
Several useful example files are installed under /etc/zfs/.
/etc/zfs/vdev_id.conf.alias.example
/etc/zfs/vdev_id.conf.multipath.example
/etc/zfs/vdev_id.conf.sas_direct.example
/etc/zfs/vdev_id.conf.sas_switch.example
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#981
Add a vdev_id feature to map device names based on already defined
udev device links. To increase the odds that vdev_id will run after
the rules it depends on, increase the vdev.rules rule number from 60
to 69. With this change, vdev_id now provides functionality analogous
to zpool_id and zpool_layout, paving the way to retire those tools.
A defined alias takes precedence over a topology-derived name, but the
two naming methods can otherwise coexist. For example, one might name
drives in a JBOD with the sas_direct topology while naming an internal
L2ARC device with an alias.
For example, the following lines in vdev_id.conf will result in the
creation of links /dev/disk/by-vdev/{d1,d2}, each pointing to the same
target as the device link specified in the third field.
# by-vdev
# name fully qualified or base name of device link
alias d1 /dev/disk/by-id/wwn-0x5000c5002de3b9ca
alias d2 wwn-0x5000c5002def789e
Also perform some minor vdev_id cleanup, such as removal of the unused
-s command line option.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#981
Remove all of the generated autotools products from the repository
and update the .gitignore files accordingly.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#718
Currently, zvols have a discard granularity set to 0, which suggests to
the upper layer that discard requests of arbirarily small size and
alignment can be made efficiently.
In practice however, ZFS does not handle unaligned discard requests
efficiently: indeed, it is unable to free a part of a block. It will
write zeros to the specified range instead, which is both useless and
inefficient (see dnode_free_range).
With this patch, zvol block devices expose volblocksize as their discard
granularity, so the upper layer is aware that it's not supposed to send
discard requests smaller than volblocksize.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#862
The end_writeback() function was changed by moving the call to
inode_sync_wait() earlier in to evict(). This effecitvely changes
the ordering of the sync but it does not impact the details of
the zfs implementation.
However, as part of this change end_writeback() was renamed to
clear_inode() to reflect the new semantics. This change does
impact us and clear_inode() now maps to end_writeback() for
kernels prior to 3.5.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#784
The vmtruncate_range() support has been removed from the kernel in
favor of using the fallocate method in the file_operations table.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
The export_operations member ->encode_fh() has been updated to
take both the child and parent inodes. This interface used to
take the child dentry and a bool describing if the parent is needed.
NOTE: While updating this code I noticed that we do not currently
cleanly handle the case where we're passed a connectable parent.
This code should be audited to make sure we're doing the right thing.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #784
Currently, zpool online -e (dynamic vdev expansion) doesn't work on
whole disks because we're invoking ioctl(BLKRRPART) from userspace
while ZFS still has a partition open on the disk, which results in
EBUSY.
This patch moves the BLKRRPART invocation from the zpool utility to the
module. Specifically, this is done just before opening the device in
vdev_disk_open() which is called inside vdev_reopen(). This requires
jumping through some hoops to get to the disk device from the partition
device, and to make sure we can still open the partition after the
BLKRRPART call.
Note that this new code path is triggered on dynamic vdev expansion
only; other actions, like creating a new pool, are unchanged and still
call BLKRRPART from userspace.
This change also depends on API changes which are available in 2.6.37
and latter kernels. The build system has been updated to detect this,
but there is no compatibility mode for older kernels. This means that
online expansion will NOT be available in older kernels. However, it
will still be possible to expand the vdev offline.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#808
As the Gentoo sys-fs/zfs maintainer, I receive license compatibility
questions and at times, those questions can be harassing. I feel that
the presence of the GPL in Gentoo's package metadata promotes such
questions. zfs.gentoo.in is the only GPLv2 licensed file in ZFS, so I
have taken the liberty of contacting all contributors to this file to
request permission to relicense it.
All of the contributors to this file have agreed to relicense it under
the 2-clause BSD license. I have added their Signed-offs to this commit,
in order of first contribution. Thank you everyone for being so
understanding.
Signed-off-by: devsk <devsku@gmail.com>
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Tselischev <andrewtselischev@gmail.com>
Signed-off-by: Zachary Bedell <zac@thebedells.org>
Signed-off-by: Gunnar Beutner <gunnar@beutner.name>
Signed-off-by: Kyle Fuller <inbox@kylefuller.co.uk>
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Closes#819
torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
vdev_id parses the file /etc/zfs/vdev_id.conf to map a physical path
in a storage topology to a channel name. The channel name is combined
with a disk enclosure slot number to create an alias that reflects the
physical location of the drive. This is particularly helpful when it
comes to tasks like replacing failed drives. Slot numbers may also be
re-mapped in case the default numbering is unsatisfactory. The drive
aliases will be created as symbolic links in /dev/disk/by-vdev.
The only currently supported topologies are sas_direct and sas_switch:
o sas_direct - a channel is uniquely identified by a PCI slot and a
HBA port
o sas_switch - a channel is uniquely identified by a SAS switch port
A multipath mode is supported in which dm-mpath devices are handled by
examining the first running component disk, as reported by 'multipath
-l'. In multipath mode the configuration file should contain a
channel definition with the same name for each path to a given
enclosure.
vdev_id can replace the existing zpool_id script on systems where the
storage topology conforms to sas_direct or sas_switch. The script
could be extended to support other topologies as well. The advantage
of vdev_id is that it is driven by a single static input file that can
be shared across multiple nodes having a common storage toplogy.
zpool_id, on the other hand, requires a unique /etc/zfs/zdev.conf per
node and a separate slot-mapping file. However, zpool_id provides the
flexibility of using any device names that show up in
/dev/disk/by-path, so it may still be needed on some systems.
vdev_id's functionality subsumes that of the sas_switch_id script, and
it is unlikely that anyone is using it, so sas_switch_id is removed.
Finally, /dev/disk/by-vdev is added to the list of directories that
'zpool import' will scan.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#713
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
The -l parameter to modprobe has been removed from the latest upstream
code and this change has entered Gentoo. Using modinfo as a substitute
addresses this.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#636
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
yshui
Paul Dagnelie
Mauricio Faria de Oliveira
Alexey Smirnoff
Michael Niewöhner
George Wilson
Pavel Zakharov
Antonio Russo
Michael Niewöhner
Henrik Riomar
beren12
Don Brady
Tony Hutter
TerraTech
Georgy Yakovlev
Brian Behlendorf
Matthew Thode
Chris Williamson
Simon Guest
Fabian-Gruenbichler
LOLi
BtbN
Giuseppe Di Natale
ka7
slashdd
Chunwei Chen
Manuel Amador (Rudd-O)
Carlo Landmeter
Grischa Zengel
James Lee
Turbo Fredriksson
yuina822
SenH
Richard Yao
DHE
Hajo Möller
Chris Dunlap
Dan Swartzendruber
alteriks
Ralf Ertzinger
Derek Dai
Ned Bass
Richard Yao
Etienne Dechamps
Ned A. Bass