When creating partition tables we always need to wait until not
only the /dev/<disk><part> device appears. But just as importantly
if we were originally given a udev path we need to wait for the
/dev/disk/*/<name>-part<part> symlink to be created. However,
since the partition naming convention differs between /dev/ and
/dev/disk we determine based on the path which convention to
expect and then wait (for a few seconds) for the device to be
created. Based on my experience with udev on my test nodes it
takes about 300ms for the devices to be created after being
prompted by the kernel. This time will vary somehwat based
on how complicated your udev rules are, so for safety I threw
in a factor of 10. We wait 3 seconds for the devices to appears
before erroring out with a failure.
An additional minor fix includes checking the force flag in the
EFI_GPT_PRIMARY_CORRUPT case. This allows you to force the
update even in the corrupt partition case.
Finally, since these are Linux only changes I've dropped the
devid code entirely here because I still can't think of why we
would need or want it on a Linux system.
After spending considerable time thinking about this I've come to the
conclusion that on Linux systems we don't need Solaris style devid
support. Instead was can simply use udev if we are careful, there
are even some advantages.
The Solaris style devid's are designed to provide a mechanism by which
a device can be opened reliably regardless of it's location in the system.
This is exactly what udev provides us on Linux, a flexible mechanism for
consistently identifing the same devices regardless of probing order.
We just need to be careful to always open the device by the path provided
at creation time, this path must be stored in ZPOOL_CONFIG_PATH. This
in fact has certain advantages.
For example, if in your system you always want the zpool to be able to
locate the disk regardless of physical location you can create the pool
using /dev/disk/by-id/. This is perhaps what you'ld want on a desktop
system where the exact location is not that important. It's more
critical that all the disks can be found.
However, in an enterprise setup there's a good chace that the physical
location of each drive is important. You have like set things up such
that your raid groups span multiple hosts adapters, such that you can
lose an adapter without downtime. In this case you would want to use
the /dev/disk/by-path/ path to ensure the path information is preserved
and you always open the disks at the right physical locations. This
would ensure your system never gets accidently misconfigured and still
just works because the zpool was still able to locate the disk.
Finally, if you want to get really fancy you can always create your
own udev rules. This way you could implement whatever lookup sceme
you wanted in user space for your drives. This would include nice
cosmetic things like being able to control the device names in tools
like zpool status, since the name as just based of the device names.
I've yet to come up with a good reason to implement devid support on
Linux since we have udev. But I've still just commented it out for now
because somebody might come up with a really good I forgot.
The majority of this this patch concerns itself with doing a direct
replacement of Solaris's libdiskmgt library with libblkid+libefi.
You'll notice that this patch removes all libdiskmgt code instead of
ifdef'ing it out. This was done to minimize any confusion when reading
the code because it seems unlikely we will ever port libdiskmgt to Linux.
Despite the replacement the behavior of the tools should have remained
the same with one exception. For the moment, we are unable to check
the partitions of devices which have an MBR style partition table when
creating a filesystem. If a non-efi partition sceme is detected on a
whole disk device we prompt the user to explicity use the force option.
It would not be a ton of work to make the tool aware of MBR style
partitions if this becomes a problem.
I've done basic sanity checking for various configurations and all
the issues I'm aware of have been addressed. Even things like blkid
misidentifing a disk as ext3 when it is added to a zfs pool. I'm
careful to always zero out the first 4k of any new zfs partition. That
all said this is all new code and while it looks like it's working right
for me we should keep an eye on it for any strange behavior.
The major change here is to fix up libefi to be linux aware. For
the most part this wasn't too hard but there were a few major issues.
First off I needed to handle the DKIOCGMEDIAINFO and DKIOCINFO ioctls.
There is no direct equivilant for these ioctls under linux. To handle
this I added wrapper functions which under Solaris simple call the ioctls.
But under Linux dig around the system a little bit getting the needed
info to fill in the requested structures.
Secondly the efi_ioctl() call was adapted such that under linux it directly
read or writes out the partition table. Under Solaris this work was
handed off to the kernel via an ioctl. In the efi_write() case we also
ensure we prompt the kernel via BLKRRPART to re-scan the new partition
table. The libefi generated partition tables are correct but older
versions of ~parted-1.8.1 can not read them without a small patch.
The kernel and fdisk are able to read them just fine.
Thirdly efi_alloc_and_init() which is used by zpool to determine if a
device is a 'wholedisk' was updated to be linux aware. This check is
performed by using the partition number for the device, which the
partition number is 0 on linux it is a 'wholedisk'. However, certain
device type such as the loopback and ram disks needed to be excluded
because they do not support partitioning.
Forthly the zpool command was made symlink aware so it can correctly
resolve udev entries such as /dev/disk/by-*/*. This symlinks are
fully expanded ensuring all block devices are recognized. When a
when a 'wholedisk' block device is detected we now properly write
out an efi label and place zfs in the first partition (0th slice).
This partition is created 1MiB in to the disk to ensure it is aligned
nicely with all high end block devices I'm aware of.
This all works for me now but it did take quite a bit of work to get
it all sorted out. It would not surprise me if certain special cases
were missed so we should keep any eye of for any odd behavior.
Because the local 'index' variable shadows the index() function
it was replaced by 'i'. Unfortunately when I made this change
I accidentally replaced one instance with 'j' resulting in the
short decimal values being printed incorrectly.
It's still not clear to me why the default value here is large
enough Solaris. I hit this limit again when setting up 120 SATA
drives configured as 15 raidz2 groups each containing 8 drives.
We expect to go bigger so we may just want to spend a little
time and figure out how to make this all dynamic.
For the moment I have added an error message to the failure path to
make it clear what happened. I have also changed the zdb ASSERT to
a VERIFY so we always catch the failure. For now we will just always
ensure the module stack is loaded, longer term we need something a
little more flexible.
Brian Behlendorf