This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
When failmode=continue is set and the pool suspends, both 'zpool status'
and the 'zfs/pool/state' kstat ignore it and report the normal vdev tree
state. There's no clear indicator that the pool is suspended. This is
unlike suspend in failmode=wait, or suspend due to MMP check failure,
which both report "SUSPENDED" explicitly.
This commit changes it so SUSPENDED is reported for failmode=continue
the same as for other modes.
Rationale:
The historical behaviour of failmode=continue is roughly, "press on as
though all is well". To this end, the fact that the pool had suspended
was not shown, to maintain the façade that all is well.
Its unclear why hiding this information was considered appropriate. One
possibility is that it was expected that a true pool fault would always
be reported as DEGRADED or FAULTED, and that the pool could not suspend
without these happening.
That is not necessarily true, as vdev health and suspend state are only
loosely connected, such that a pool in (apparent) good health can be
suspended for good reasons, and of course a degraded pool does not lead
to suspension. Even if that expectation were true, there's still a
difference in urgency - a degraded pool may not need to be attended to
for hours, while a suspended pool is most often unusable until an
operator intervenes.
An operator that has set failmode=continue has presumably done so
because their workload is one that can continue to operate in a useful
way when the pool suspends. In this case the operator still needs a
clear indicator that there is a problem that needs attending to.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15297
When the vdev properties features was merged an extra check
was added in `spa_vdev_remove_top_check()` which checked
whether the vdev that we want to remove is already being
removed and if so return an EALREADY error.
```
static int
spa_vdev_remove_top_check(vdev_t *vd)
{
... <snip> ...
/*
* This device is already being removed
*/
if (vd->vdev_removing)
return (SET_ERROR(EALREADY));
```
Before that change we'd still fail with an error but it
was a more generic one - here is the check that failed
later in the same function:
```
/*
* There can not be a removal in progress.
*/
if (spa->spa_removing_phys.sr_state == DSS_SCANNING)
return (SET_ERROR(EBUSY));
```
Changing the error code returned from that function changed
the behavior of the removal's library interface exposed to
the userland - `spa_vdev_remove()` now returns `EZFS_UNKNOWN`
instead of `EZFS_EBUSY` that was returning before.
This patch adds logic to make `spa_vdev_remove()` mindful
of the new EALREADY code and propagating `EZFS_EBUSY`
reverting to the previously established semantics of that
function.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#15013Closes#15129
Added a flag '-e' in zpool scrub to scrub only blocks in error log. A
user can pause, resume and cancel the error scrub by passing additional
command line arguments -p -s just like a regular scrub. This involves
adding a new flag, creating new libzfs interfaces, a new ioctl, and the
actual iteration and read-issuing logic. Error scrubbing is executed in
multiple txg to make sure pool performance is not affected.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain tulsi.jain@delphix.com
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#8995Closes#12355
zpool initialize functions well for touching every free byte...once.
But if we want to do it again, we're currently out of luck.
So let's add zpool initialize -u to clear it.
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12451Closes#14873
Usage:
zpool set org.freebsd:comment="this is my pool" poolname
Tests are based on zfs_set's user property tests.
Also stop truncating property values at MAXNAMELEN, use ZFS_MAXPROPLEN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Beckhoff Automation GmbH & Co. KG.
Sponsored-by: Klara Inc.
Closes#11680
And add it to the AVZ, this is not backwards compatible with older pools
due to an assertion in spa_sync() that verifies the number of ZAPs of
all vdevs matches the number of ZAPs in the AVZ.
Granted, the assertion only applies to #DEBUG builds - still, a feature
flag is introduced to avoid the assertion, com.klarasystems:vdev_zaps_v2
Notably, this allows to get/set properties on the root vdev:
% zpool set user:prop=value <pool> root-0
Before this commit, it was already possible to get/set properties on
top-level vdevs with the syntax <type>-<vdev_id> (e.g. mirror-0):
% zpool set user:prop=value <pool> mirror-0
This syntax also applies to the root vdev as it is is of type 'root'
with a vdev_id of 0, root-0. The keyword 'root' as an alias for
'root-0'.
The following tests have been added:
- zpool get all properties from root vdev
- zpool set a property on root vdev
- verify root vdev ZAP is created
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology
Submitted-by: Klara, Inc.
Closes#14405
After addressing coverity complaints involving `nvpair_name()`, the
compiler started complaining about dropping const. This lead to a rabbit
hole where not only `nvpair_name()` needed to be constified, but also
`nvpair_value_string()`, `fnvpair_value_string()` and a few other static
functions, plus variable pointers throughout the code. The result became
a fairly big change, so it has been split out into its own patch.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
The strings returned from parsing nvlists should be immutable, but to
simplify the code when we want a substring from it, we sometimes will
write a NULL into it and then restore the value afterward. Provided
there is no concurrent access, this is okay, unless we forget to restore
the value afterward. This was caught when constifying string functions
related to nvlists.
Reviewed-by: Tino Reichardt <milky-zfs@mcmilk.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14612
Block Cloning allows to manually clone a file (or a subset of its
blocks) into another (or the same) file by just creating additional
references to the data blocks without copying the data itself.
Those references are kept in the Block Reference Tables (BRTs).
The whole design of block cloning is documented in module/zfs/brt.c.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13392
Introduce four new vdev properties:
checksum_n
checksum_t
io_n
io_t
These properties can be used for configuring the thresholds of zed's
diagnosis engine and are interpeted as <N> events in T <seconds>.
When this property is set to a non-default value on a top-level vdev,
those thresholds will also apply to its leaf vdevs. This behavior can be
overridden by explicitly setting the property on the leaf vdev.
Note that, these properties do not persist across vdev replacement. For
this reason, it is advisable to set the property on the top-level vdev
instead of the leaf vdev.
The default values for zed's diagnosis engine (10 events, 600 seconds)
remains unchanged.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rob Wing <rob.wing@klarasystems.com>
Sponsored-by: Seagate Technology LLC
Closes#13805
This commit supports for spare vdev hotplug. The
spare vdev associated with all the pools will be
marked as "Removed" when the drive is physically
detached and will become "Available" when the
drive is reattached. Currently, the spare vdev
status does not change on the drive removal and
the same is the case with reattachment.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#14295
There is a lock order inversion deadlock between `spa_errlog_lock` and
`dp_config_rwlock`:
A thread in `spa_delete_dataset_errlog()` is running from a sync task.
It is holding the `dp_config_rwlock` for writer (see
`dsl_sync_task_sync()`), and waiting for the `spa_errlog_lock`.
A thread in `dsl_pool_config_enter()` is holding the `spa_errlog_lock`
(see `spa_get_errlog_size()`) and waiting for the `dp_config_rwlock` (as
reader).
Note that this was introduced by #12812.
This commit address this by defining the lock ordering to be
dp_config_rwlock first, then spa_errlog_lock / spa_errlist_lock.
spa_get_errlog() and spa_get_errlog_size() can acquire the locks in this
order, and then process_error_block() and get_head_and_birth_txg() can
verify that the dp_config_rwlock is already held.
Additionally, a buffer overrun in `spa_get_errlog()` is corrected. Many
code paths didn't check if `*count` got to zero, instead continuing to
overwrite past the beginning of the userspace buffer at `uaddr`.
Tested by having some errors in the pool (via `zinject -t data
/path/to/file`), one thread running `zpool iostat 0.001`, and another
thread runs `zfs destroy` (in a loop, although it hits the first time).
This reproduces the problem easily without the fix, and works with the
fix.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#14239Closes#14289
This fixes -Wsingle-bit-bitfield-constant-conversion warning from
clang-16 like:
lib/libzfs/libzfs_dataset.c:4529:19: error: implicit truncation
from 'int' to a one-bit wide bit-field changes value from
1 to -1 [-Werror,-Wsingle-bit-bitfield-constant-conversion]
flags.nounmount = B_TRUE;
^ ~~~~~~
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Signed-off-by: Brooks Davis <brooks.davis@sri.com>
Closes#14125
This confused Clang's static analyzer, making it think there was a
possible NULL pointer dereference. There is no NULL pointer dereference.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#14042
These were categorized as the following:
* Dead assignment 23
* Dead increment 4
* Dead initialization 6
* Dead nested assignment 18
Most of these are harmless, but since actual issues can hide among them,
we correct them.
That said, there were a few return values that were being ignored that
appeared to merit some correction:
* `destroy_callback()` in `cmd/zfs/zfs_main.c` ignored the error from
`destroy_batched()`. We handle it by returning -1 if there is an
error.
* `zfs_do_upgrade()` in `cmd/zfs/zfs_main.c` ignored the error from
`zfs_for_each()`. We handle it by doing a binary OR of the error
value from the subsequent `zfs_for_each()` call to the existing
value. This is how errors are mostly handled inside `zfs_for_each()`.
The error value here is passed to exit from the zfs command, so doing
a binary or on it is better than what we did previously.
* `get_zap_prop()` in `module/zfs/zcp_get.c` ignored the error from
`dsl_prop_get_ds()` when the property is not of type string. We
return an error when it does. There is a small concern that the
`zfs_get_temporary_prop()` call would handle things, but in the case
that it does not, we would be pushing an uninitialized numval onto
the lua stack. It is expected that `dsl_prop_get_ds()` will succeed
anytime that `zfs_get_temporary_prop()` does, so that not giving it a
chance to fix things is not a problem.
* `draid_merge_impl()` in `tests/zfs-tests/cmd/draid.c` used
`nvlist_add_nvlist()` twice in ways in which errors are expected to
be impossible, so we switch to `fnvlist_add_nvlist()`.
A few notable ones did not merit use of the return value, so we
suppressed it with `(void)`:
* `write_free_diffs()` in `lib/libzfs/libzfs_diff.c` ignored the error
value from `describe_free()`. A look through the commit history
revealed that this was intentional.
* `arc_evict_hdr()` in `module/zfs/arc.c` did not need to use the
returned handle from `arc_hdr_realloc()` because it is already
referenced in lists.
* `spa_vdev_detach()` in `module/zfs/spa.c` has a comment explicitly
saying not to use the error from `vdev_label_init()` because whatever
causes the error could be the reason why a detach is being done.
Unfortunately, I am not presently able to analyze the kernel modules
with Clang's static analyzer, so I could have missed some cases of this.
In cases where reports were present in code that is duplicated between
Linux and FreeBSD, I made a conscious effort to fix the FreeBSD version
too.
After this commit is merged, regressions like dee8934 should become
extremely obvious with Clang's static analyzer since a regression would
appear in the results as the only instance of unused code. That assumes
that Coverity does not catch the issue first.
My local branch with fixes from all of my outstanding non-draft pull
requests shows 118 reports from Clang's static anlayzer after this
patch. That is down by 51 from 169.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13986
ZED does not take any action for disk removal events if there is no
spare VDEV available. Added zpool_vdev_remove_wanted() in libzfs
and vdev_remove_wanted() in vdev.c to remove the VDEV through ZED
on removal event. This means that if you are running zed and
remove a disk, it will be properly marked as REMOVED.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Ameer Hamza <ahamza@ixsystems.com>
Closes#13797
Otherwise, `strlcat()` can overflow them.
Coverity found this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Signed-off-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Closes#13866
This is an oddly specific function that has never had any consumers in
the history of this repo. Get rid of it and the pile of helper
functions that exist for it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13724
`libzfs_pool.c` uses the name `msg` where everywhere else in libzfs uses
`errbuf` for the error message buffer.
Use the name consistent with the rest of libzfs and use ERRBUFLEN
instead of 1024.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13539
Every errbuf array in libzfs is 1024 chars.
Define ERRBUFLEN in a shared header, and use it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13539
The corresponding function 'zpool_get_history' in libzfs would printing
an error messages only when the ioctl call failed.
Add missing error reporting, specifically memory allocation failures
and error from 'zpool_history_unpack'.
Also avoid possibly reading of uninitialized 'err' variable in case
the requested offset pasts EOF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: WHR <msl0000023508@gmail.com>
Issue #13322Closes#13320
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
Improves readability. No functional change intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13197
This code can be failure prone on FreeBSD, where zfsd will pass a guid
as the vdev path to online. The guid causes zfs_resolve_shortname to
fail because it expects a path. We can just skip the whole ordeal.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#12083
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
Found by clang 14 with -Wunused-but-set-variable
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12829
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Currently, you get back "can only attach to mirrors and top-level disks"
unconditionally if zpool attach returns ENOTSUP, but that also happens
if, say, feature@device_rebuild=disabled and you tried attach -s.
So let's print an error for that case, lest people go down a rabbit hole
looking into what they did wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11414Closes#12680
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Could have gone either way with this one, either adding it to
macOS/Windows SPL, or returning it to "classic" usage with strrchr().
Since the new special way isn't really used, and only used once,
we have this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes #12312
There are at least two interpretations of basename(3),
in addition to both functions being allowed to /both/ return a static
buffer (unsuitable in multi-threaded environments) /and/ raze the input
(which encourages overallocations, at best)
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12105
In `zpool_load_compat()`:
* initialize `l_features[]` with a loop rather than a static
initializer.
* don't redefine system constants; use private names instead
Rationale here:
When an array is initialized using a static {foo}, only the specified
members are initialized to the provided values, the rest are
initialized to zero. While B_FALSE is of course zero, it feels
unsafe to rely on this being true forever, so I'm inclined to sacrifice
a few microseconds of runtime here and initialize using a loop.
When looking for the correct combination of system constants to use
(in open() and mmap()), I prefer to use private constants rather than
redefining system ones; due to the small chance that the system
ones might be referenced later in the file. So rather than defining
O_PATH and MAP_POPULATE, I use distinct constant names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#12156
As a bonus, this also passes the open flags into the open flags instead
of the mode (it worked by accident because O_RDONLY is 0),
correctly detects a failed map,
and prefaults the entire file since we're always writing to every page
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11993
Several improvements to the operation of the 'compatibility' property:
1) Improved handling of unrecognized features:
Change the way unrecognized features in compatibility files are handled.
* invalid features in files under /usr/share/zfs/compatibility.d
only get a warning (as these may refer to future features not yet in
the library),
* invalid features in files under /etc/zfs/compatibility.d
get an error (as these are presumed to refer to the current system).
2) Improved error reporting from zpool_load_compat.
Note: slight ABI change to zpool_load_compat for better error reporting.
3) compatibility=legacy inhibits all 'zpool upgrade' operations.
4) Detect when features are enabled outside current compatibility set
* zpool set compatibility=foo <-- print a warning
* zpool set feature@xxx=enabled <-- error
* zpool status <-- indicate this state
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11861
As found by
git grep -E '(open|setmntent|pipe2?)\(' |
grep -vE '((zfs|zpool)_|fd|dl|lzc_re|pidfile_|g_)open\('
FreeBSD's pidfile_open() says nothing about the flags of the files it
opens, but we can't do anything about it anyway; the implementation does
open all files with O_CLOEXEC
Consider this output with zpool.d/media appended with
"pid=$$; (ls -l /proc/$pid/fd > /dev/tty)":
$ /sbin/zpool iostat -vc media
lrwx------ 0 -> /dev/pts/0
l-wx------ 1 -> 'pipe:[3278500]'
l-wx------ 2 -> /dev/null
lrwx------ 3 -> /dev/zfs
lr-x------ 4 -> /proc/31895/mounts
lrwx------ 5 -> /dev/zfs
lr-x------ 10 -> /usr/lib/zfs-linux/zpool.d/media
vs
$ ./zpool iostat -vc vendor,upath,iostat,media
lrwx------ 0 -> /dev/pts/0
l-wx------ 1 -> 'pipe:[3279887]'
l-wx------ 2 -> /dev/null
lr-x------ 10 -> /usr/lib/zfs-linux/zpool.d/media
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11866
When specifying the name of a RAIDZ vdev on the command line, it can be
specified as raidz-<vdevID> or raidzP-<vdevID>.
e.g. `zpool clear poolname raidz-0` or `zpool clear poolname raidz2-0`
If the parity is specified in the vdev name, it should match the actual
parity of that RAIDZ vdev, otherwise the command should fail. This
commit makes it so.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Stuart Maybee <stuart.maybee@comcast.net>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11742
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11775
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
Don Brady
Rob N
Serapheim Dimitropoulos
George Amanakis
Brian Behlendorf
Allan Jude
rob-wing
Richard Yao
Pawel Jakub Dawidek
Ameer Hamza
Matthew Ahrens
Brooks Davis
Ryan Moeller
Tino Reichardt
наб
Ryan Moeller
Low-power
Jorgen Lundman
Paul Dagnelie
Rich Ercolani
Colm
Matthew Ahrens
Andrea Gelmini