The cast will explode on 32-bit big-endian architectures
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12968
This reverts commit f6a0dac84a.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12938
If the fields to be listed and sorted by are constrained
to those populated by dsl_dataset_fast_stat(), then
zfs list is much faster, as it does not need to open each
objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name
much faster.
However, it was limited to `-o name -s name`, this work
extends this optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties
supported by dsl_dataset_fast_stat() or similar, that do
not require extra locking or reading from disk.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11080
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
When zfs_nicestrtonum() is called and there will be an error,
the message is left in libzfs handle, if provided. We can use
this message, to provide better feedback for user.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#12650
When you create a pool, zfs writes vd->vdev_enc_sysfs_path with the
enclosure sysfs path to the fault LEDs, like:
vdev_enc_sysfs_path = /sys/class/enclosure/0:0:1:0/SLOT8
However, this enclosure path doesn't get updated on successive imports
even if enclosure path to the disk changes. This patch fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11950Closes#12095
This patch allows you to clear the label on offlined disks in an active
pool with `-f`. Previously, labelclear wouldn't let you do that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12511
Previously, zpool-iostat did not display any data regarding rebuild I/Os
in either the latency/size histograms (-w/-l/-r) or the queue data (-q).
This fix essentially utilizes the existing infrastructure for tracking
rebuild queue data and displays this data in the proper places within
zpool-iostat's output.
Signed-off-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Signed-off-by: Trevor Bautista <tbautista@lanl.gov>
Co-authored-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
`zpool_do_import()` passes `argv[0]`, (optionally) `argv[1]`, and
`pool_specified` to `import_pools()`. If `pool_specified==FALSE`, the
`argv[]` arguments are not used. However, these values may be off the
end of the `argv[]` array, so loading them could dereference unmapped
memory. This error is reported by the asan build:
```
=================================================================
==6003==ERROR: AddressSanitizer: heap-buffer-overflow
READ of size 8 at 0x6030000004a8 thread T0
#0 0x562a078b50eb in zpool_do_import zpool_main.c:3796
#1 0x562a078858c5 in main zpool_main.c:10709
#2 0x7f5115231bf6 in __libc_start_main
#3 0x562a07885eb9 in _start
0x6030000004a8 is located 0 bytes to the right of 24-byte region
allocated by thread T0 here:
#0 0x7f5116ac6b40 in __interceptor_malloc
#1 0x562a07885770 in main zpool_main.c:10699
#2 0x7f5115231bf6 in __libc_start_main
```
This commit passes NULL for these arguments if they are off the end
of the `argv[]` array.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#12339
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
There used to be a warning after upgrading a zpool in FreeBSD, so users
won't forget to update the boot loader that pool is booted from.
This change brings this warning back, but only if the bootfs property
is set on the pool, which should be sufficient for the vast majority of
FreeBSD installations. People running something custom are most likely
aware of what to do after an upgrade in their specific environment.
Functionality is implemented in an OS specific helper function.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Michael Gmelin <grembo@FreeBSD.org>
Signed-off-by: Michael Gmelin <grembo@FreeBSD.org>
Closes#12099Closes#12104
Propagate vdev child state to parents on invalid label
Add VDEV_AUX_BAD_LABEL to print_import_config()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Signed-off-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Closes#12088
Do not (incorrectly, right instead left) pad health string itself,
it will be taken care of when printing property value below.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#11899
Several improvements to the operation of the 'compatibility' property:
1) Improved handling of unrecognized features:
Change the way unrecognized features in compatibility files are handled.
* invalid features in files under /usr/share/zfs/compatibility.d
only get a warning (as these may refer to future features not yet in
the library),
* invalid features in files under /etc/zfs/compatibility.d
get an error (as these are presumed to refer to the current system).
2) Improved error reporting from zpool_load_compat.
Note: slight ABI change to zpool_load_compat for better error reporting.
3) compatibility=legacy inhibits all 'zpool upgrade' operations.
4) Detect when features are enabled outside current compatibility set
* zpool set compatibility=foo <-- print a warning
* zpool set feature@xxx=enabled <-- error
* zpool status <-- indicate this state
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11861
zpool list, which is the only user, would mistakenly try to parse the
empty string as the interval in this case:
$ zpool list "a"
cannot open 'a': no such pool
$ zpool list ""
interval cannot be zero
usage: <usage string follows>
which is now symmetric with zpool get:
$ zpool list ""
cannot open '': name must begin with a letter
Avoid breaking the "interval cannot be zero" string.
There simply isn't a need for this, and it's user-facing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11841Closes#11843
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
Bring the output of the removal status in line with the other
"fields" that zpool status outputs, and thus allows an parser to
easier detect this as continuation of the 'remove:' output.
Before:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Now:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Closes#11674
After 35ec517 it has become possible to import ZFS pools witn an
active org.illumos:edonr feature on FreeBSD, leading to a panic.
In addition, "zpool status" reported all pools without edonr
as upgradable and "zpool upgrade -v" reported edonr in the list
of upgradable features.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11653
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
Rather than conditionally compiling out the edonr code for FreeBSD
update zfs_mod_supported_feature() to indicate this feature is
unsupported. This ensures that all spa features are defined on
every platform, even if they are not supported.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11605
Issue #11468
Explicitly check for NULL to satisfy cppcheck that "val" can never
be NULL when passed to printf(). This looks like a false positive
since is_blank_str() can never take the false conditional branch
when passed a NULL. But there's no harm in adding the extra check.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
When creating a pool only features supported by both user and
kernel space should be enabled. Furthermore, improve the error
messages when attempting to create, or add, a dRAID vdev when
the dRAID feature is not supported by the kernel modules.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11492
Each zfs ioctl that changes on-disk state (e.g. set property, create
snapshot, destroy filesystem) is recorded in the zpool history, and is
printed by `zpool history -i`.
For performance diagnostic purposes, it would be useful to know how long
each of these ioctls took to run. This commit adds that functionality,
with a new `ZPOOL_HIST_ELAPSED_NS` member of the history nvlist.
Additionally, the time recorded in this history log is currently the
time that the history record is written to disk. But in many cases (CLI
args logging and ioctl logging), this happens asynchronously,
potentially many seconds after the operation completed. This commit
changes the timestamp to reflect when the history event was created,
rather than when it was written to disk.
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11440
Use the correct return type for getopt otherwise clang complains
about tautological-constant-out-of-range-compare.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterling Jensen <sterlingjensen@users.noreply.github.com>
Closes#11359
`zpool create -n` fails to list cache and spare vdevs.
`zpool add -n` fails to list spare devices.
`zpool split -n` fails to list `special` and `dedup` labels.
`zpool add -n` and `zpool split -n` shouldn't list hole devices.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11122Closes#11167
When ZFS_COLOR is set, zpool status shows row headings in bold,
except for the "remove:" heading. This is a quick fix that makes
it print in bold too.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Sun <me@andrewsun.com>
Closes#11255
zpool_expand_proplist() now ignores pl_fixed if its new literal
argument is true. The rest is a consequence of needing to pass
that down.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiao?=~Dska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11202
The output of ZFS channel programs is logged on-disk in the zpool
history, and printed by `zpool history -i`. Channel programs can use
10MB of memory by default, and up to 100MB by using the `zfs program -m`
flag. Therefore their output can be up to some fraction of 100MB.
In addition to being somewhat wasteful of the limited space reserved for
the pool history (which for large pools is 1GB), in extreme cases this
can result in a failure of `ASSERT(length <= DMU_MAX_ACCESS);` in
`dmu_buf_hold_array_by_dnode()`.
This commit limits the output size that will be logged to 1MB. Larger
outputs will not be logged, instead a entry will be logged indicating
the size of the omitted output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11194
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
This solves issues occurring with a different decimal operator and
keeps the command line interface consistent for all locales .
E.g. `zfs set quota=0.5T`
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Felix Neumärker <xdch47@posteo.de>
Closes#10878
Many modern devices use physical allocation units that are much
larger than the minimum logical allocation size accessible by
external commands. Two prevalent examples of this are 512e disk
drives (512b logical sector, 4K physical sector) and flash devices
(512b logical sector, 4K or larger allocation block size, and 128k
or larger erase block size). Operations that modify less than the
physical sector size result in a costly read-modify-write or garbage
collection sequence on these devices.
Simply exporting the true physical sector of the device to ZFS would
yield optimal performance, but has two serious drawbacks:
1. Existing pools created with devices that have different logical
and physical block sizes, but were configured to use the logical
block size (e.g. because the OS version used for pool construction
reported the logical block size instead of the physical block
size) will suddenly find that the vdev allocation size has
increased. This can be easily tolerated for active members of
the array, but ZFS would prevent replacement of a vdev with
another identical device because it now appears that the smaller
allocation size required by the pool is not supported by the new
device.
2. The device's physical block size may be too large to be supported
by ZFS. The optimal allocation size for the vdev may be quite
large. For example, a RAID controller may export a vdev that
requires read-modify-write cycles unless accessed using 64k
aligned/sized requests. ZFS currently has an 8k minimum block
size limit.
Reporting both the logical and physical allocation sizes for vdevs
solves these problems. A device may be used so long as the logical
block size is compatible with the configuration. By comparing the
logical and physical block sizes, new configurations can be optimized
and administrators can be notified of any existing pools that are
sub-optimal.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Macy <mmacy@freebsd.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10619
== Motivation and Context
The current implementation of 'sharenfs' and 'sharesmb' relies on
the use of the sharetab file. The use of this file is os-specific
and not required by linux or freebsd. Currently the code must
maintain updates to this file which adds complexity and presents
a significant performance impact when sharing many datasets. In
addition, concurrently running 'zfs sharenfs' command results in
missing entries in the sharetab file leading to unexpected failures.
== Description
This change removes the sharetab logic from the linux and freebsd
implementation of 'sharenfs' and 'sharesmb'. It still preserves an
os-specific library which contains the logic required for sharing
NFS or SMB. The following entry points exist in the vastly simplified
libshare library:
- sa_enable_share -- shares a dataset but may not commit the change
- sa_disable_share -- unshares a dataset but may not commit the change
- sa_is_shared -- determine if a dataset is shared
- sa_commit_share -- notify NFS/SMB subsystem to commit the shares
- sa_validate_shareopts -- determine if sharing options are valid
The sa_commit_share entry point is provided as a performance enhancement
and is not required. The sa_enable_share/sa_disable_share may commit
the share as part of the implementation. Libshare provides a framework
for both NFS and SMB but some operating systems may not fully support
these protocols or all features of the protocol.
NFS Operation:
For linux, libshare updates /etc/exports.d/zfs.exports to add
and remove shares and then commits the changes by invoking
'exportfs -r'. This file, is automatically read by the kernel NFS
implementation which makes for better integration with the NFS systemd
service. For FreeBSD, libshare updates /etc/zfs/exports to add and
remove shares and then commits the changes by sending a SIGHUP to
mountd.
SMB Operation:
For linux, libshare adds and removes files in /var/lib/samba/usershares
by calling the 'net' command directly. There is no need to commit the
changes. FreeBSD does not support SMB.
== Performance Results
To test sharing performance we created a pool with an increasing number
of datasets and invoked various zfs actions that would enable and
disable sharing. The performance testing was limited to NFS sharing.
The following tests were performed on an 8 vCPU system with 128GB and
a pool comprised of 4 50GB SSDs:
Scale testing:
- Share all filesystems in parallel -- zfs sharenfs=on <dataset> &
- Unshare all filesystems in parallel -- zfs sharenfs=off <dataset> &
Functional testing:
- share each filesystem serially -- zfs share -a
- unshare each filesystem serially -- zfs unshare -a
- reset sharenfs property and unshare -- zfs inherit -r sharenfs <pool>
For 'zfs sharenfs=on' scale testing we saw an average reduction in time
of 89.43% and for 'zfs sharenfs=off' we saw an average reduction in time
of 83.36%.
Functional testing also shows a huge improvement:
- zfs share -- 97.97% reduction in time
- zfs unshare -- 96.47% reduction in time
- zfs inhert -r sharenfs -- 99.01% reduction in time
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Bryant G. Ly <bryangly@gmail.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-68690
Closes#1603Closes#7692Closes#7943Closes#10300
The device_rebuild feature enables sequential reconstruction when
resilvering. Mirror vdevs can be rebuilt in LBA order which may
more quickly restore redundancy depending on the pools average block
size, overall fragmentation and the performance characteristics
of the devices. However, block checksums cannot be verified
as part of the rebuild thus a scrub is automatically started after
the sequential resilver completes.
The new '-s' option has been added to the `zpool attach` and
`zpool replace` command to request sequential reconstruction
instead of healing reconstruction when resilvering.
zpool attach -s <pool> <existing vdev> <new vdev>
zpool replace -s <pool> <old vdev> <new vdev>
The `zpool status` output has been updated to report the progress
of sequential resilvering in the same way as healing resilvering.
The one notable difference is that multiple sequential resilvers
may be in progress as long as they're operating on different
top-level vdevs.
The `zpool wait -t resilver` command was extended to wait on
sequential resilvers. From this perspective they are no different
than healing resilvers.
Sequential resilvers cannot be supported for RAIDZ, but are
compatible with the dRAID feature being developed.
As part of this change the resilver_restart_* tests were moved
in to the functional/replacement directory. Additionally, the
replacement tests were renamed and extended to verify both
resilvering and rebuilding.
Original-patch-by: Isaac Huang <he.huang@intel.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: John Poduska <jpoduska@datto.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10349
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
zpool wait brought in sem_init() and family, which is a primitive set
not previously used in Open ZFS. It also happens to be deprecated
on macOS. Replace with phtread API calls.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10468
As we do not expect the destination of these strncpy calls to be NULL
terminated, substitute them with memcpy.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10346
If the reported terminal width is 0 or less than 42, the signed variable
width was set to a negative number that was then assigned to the
unsigned column width becoming a huge number.
Add comments and change logic to better explain what's happening.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Philip Pokorny <ppokorny@mindspring.com>
Closes#10247
On zpools containing hole vdevs (e.g. removed log devices), the `zpool
trim` (and presumably `zpool initialize`) commands will attempt calling
their respective functions on "hole", which fails, as this is not a real
vdev.
Avoid this by removing HOLE vdevs in zpool_collect_leaves.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Niklas Haas <git@haasn.xyz>
Closes#10227
The test for VDEV_TYPE_INDIRECT is done after a memory allocation, and
could return from function without freeing it. Since we don't need that
allocation yet, just postpone it.
Add a missing free() when buffer is no longer needed.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: João Carlos Mendes Luís <jonny@jonny.eng.br>
Closes#10193
Manual trims fall into the category of long-running pool activities
which people might want to wait synchronously for. This change adds
support to 'zpool wait' for waiting for manual trim operations to
complete. It also adds a '-w' flag to 'zpool trim' which can be used to
turn 'zpool trim' into a synchronous operation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#10071
-fno-common is the new default in GCC 10, replacing -fcommon in
GCC <= 9, so static data must only be allocated once.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@european-processor-initiative.eu>
Closes#9943
Update the project website links contained in to repository to
reference the secure https://zfsonlinux.org address.
Reviewed-By: Richard Laager <rlaager@wiktel.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Garrett Fields <ghfields@gmail.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9837
For dedup, special and log devices "zpool add -n" does not print
correctly their vdev type:
~# zpool add -n pool dedup /tmp/dedup special /tmp/special log /tmp/log
would update 'pool' to the following configuration:
pool
/tmp/normal
/tmp/dedup
/tmp/special
/tmp/log
This could lead storage administrators to modify their ZFS pools to
unexpected and unintended vdev configurations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9783Closes#9390
If the ZFS_COLOR env variable is set, then use ANSI color
output in zpool status:
- Column headers are bold
- Degraded or offline pools/vdevs are yellow
- Non-zero error counters and faulted vdevs/pools are red
- The 'status:' and 'action:' sections are yellow if they're
displaying a warning.
This also includes a new 'faketty' function in libtest.shlib that is
compatible with FreeBSD (code provided by @freqlabs).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#9340
FreeBSD has no analog. Buffered block devices were removed a decade
plus ago.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9508
In original implementation, zpool history will read the whole history
before printing anything, causing memory usage goes unbounded. We fix
this by breaking it into read-print iterations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#9516
Factor Linux specific functions out of the zpool command.
Reviewed-by: Allan Jude <allanjude@freebsd.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9333
Move the trailing newlines from the error message strings to the format
strings to more closely match the other error messages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9330
Currently the best way to wait for the completion of a long-running
operation in a pool, like a scrub or device removal, is to poll 'zpool
status' and parse its output, which is neither efficient nor convenient.
This change adds a 'wait' subcommand to the zpool command. When invoked,
'zpool wait' will block until a specified type of background activity
completes. Currently, this subcommand can wait for any of the following:
- Scrubs or resilvers to complete
- Devices to initialized
- Devices to be replaced
- Devices to be removed
- Checkpoints to be discarded
- Background freeing to complete
For example, a scrub that is in progress could be waited for by running
zpool wait -t scrub <pool>
This also adds a -w flag to the attach, checkpoint, initialize, replace,
remove, and scrub subcommands. When used, this flag makes the operations
kicked off by these subcommands synchronous instead of asynchronous.
This functionality is implemented using a new ioctl. The type of
activity to wait for is provided as input to the ioctl, and the ioctl
blocks until all activity of that type has completed. An ioctl was used
over other methods of kernel-userspace communiction primarily for the
sake of portability.
Porting Notes:
This is ported from Delphix OS change DLPX-44432. The following changes
were made while porting:
- Added ZoL-style ioctl input declaration.
- Reorganized error handling in zpool_initialize in libzfs to integrate
better with changes made for TRIM support.
- Fixed check for whether a checkpoint discard is in progress.
Previously it also waited if the pool had a checkpoint, instead of
just if a checkpoint was being discarded.
- Exposed zfs_initialize_chunk_size as a ZoL-style tunable.
- Updated more existing tests to make use of new 'zpool wait'
functionality, tests that don't exist in Delphix OS.
- Used existing ZoL tunable zfs_scan_suspend_progress, together with
zinject, in place of a new tunable zfs_scan_max_blks_per_txg.
- Added support for a non-integral interval argument to zpool wait.
Future work:
ZoL has support for trimming devices, which Delphix OS does not. In the
future, 'zpool wait' could be extended to add the ability to wait for
trim operations to complete.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: John Gallagher <john.gallagher@delphix.com>
Closes#9162
Both 'detach' and 'online' zpool subcommands, when provided with an
unsupported option, forget to print it in the error message:
# zpool online -t rpool vda3
invalid option ''
usage:
online [-e] <pool> <device> ...
This changes fixes the error message in order to include the actual
option that is not supported.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9270
s/get_vdev_spec/make_root_vdev
The former doesn't exist anymore.
Sponsored by: iXsystems, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Ryan Moeller <ryan@freqlabs.com>
Closes#8759
On systems where "char" is an unsigned type the value returned by
getopt() will never be negative (-1), leading to an endless loop:
this issue prevents both 'zpool remove' and 'zstreamdump' for
working on some systems.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8789
This commit adds the undocumented "-t" option to zpool(8) help message.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8782
This commit removes the documented but not handled "-p" option from
zpool(8) help message.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#8781
Users of existing pools, especially pools with top-level encrypted
datasets, could run into trouble trying to work around Errata #4.
Clarify that removing encrypted snapshots and bookmarks is enough
to clear the errata.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Justin Scholz <git@justinscholz.de>
Closes#8682Closes#8683
Currently, it is possible for the 'zpool scrub' command to
progress slightly beyond 100% due to concurrent changes
happening on the live pool. This behavior is expected, but
the userspace code for 'zpool status' would subtract the
expected amount of data from the amount of data already
scrubbed, resulting in a negative integer being casted to a
large positive one. This number was then used to calculate
the estimated completion time, resulting in wildly wrong
results. This code changes the behavior so that 'zpool status'
does not attempt to report an estimate during this period.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8611Closes#8687
Add the 'zfs version' and 'zpool version' subcommands to display
the version of the user space utilities and loaded zfs kernel
module. For example:
$ zfs version
zfs-0.8.0-rc3_169_g67e0366b88
zfs-kmod-0.8.0-rc3_169_g67e0366b88
The '-V' and '--version' aliases were added to support the
common convention of using 'zfs --version` to obtain the version
information.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: TerraTech <1118433+TerraTech@users.noreply.github.com>
Closes#2501Closes#8567
UNMAP/TRIM support is a frequently-requested feature to help
prevent performance from degrading on SSDs and on various other
SAN-like storage back-ends. By issuing UNMAP/TRIM commands for
sectors which are no longer allocated the underlying device can
often more efficiently manage itself.
This TRIM implementation is modeled on the `zpool initialize`
feature which writes a pattern to all unallocated space in the
pool. The new `zpool trim` command uses the same vdev_xlate()
code to calculate what sectors are unallocated, the same per-
vdev TRIM thread model and locking, and the same basic CLI for
a consistent user experience. The core difference is that
instead of writing a pattern it will issue UNMAP/TRIM commands
for those extents.
The zio pipeline was updated to accommodate this by adding a new
ZIO_TYPE_TRIM type and associated spa taskq. This new type makes
is straight forward to add the platform specific TRIM/UNMAP calls
to vdev_disk.c and vdev_file.c. These new ZIO_TYPE_TRIM zios are
handled largely the same way as ZIO_TYPE_READs or ZIO_TYPE_WRITEs.
This makes it possible to largely avoid changing the pipieline,
one exception is that TRIM zio's may exceed the 16M block size
limit since they contain no data.
In addition to the manual `zpool trim` command, a background
automatic TRIM was added and is controlled by the 'autotrim'
property. It relies on the exact same infrastructure as the
manual TRIM. However, instead of relying on the extents in a
metaslab's ms_allocatable range tree, a ms_trim tree is kept
per metaslab. When 'autotrim=on', ranges added back to the
ms_allocatable tree are also added to the ms_free tree. The
ms_free tree is then periodically consumed by an autotrim
thread which systematically walks a top level vdev's metaslabs.
Since the automatic TRIM will skip ranges it considers too small
there is value in occasionally running a full `zpool trim`. This
may occur when the freed blocks are small and not enough time
was allowed to aggregate them. An automatic TRIM and a manual
`zpool trim` may be run concurrently, in which case the automatic
TRIM will yield to the manual TRIM.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Contributions-by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Contributions-by: Tim Chase <tim@chase2k.com>
Contributions-by: Chunwei Chen <tuxoko@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8419Closes#598
1) As implemented the `zpool labelclear` command overwrites
the calculated offsets of all four vdev labels even when only a
single valid label is found. If the device as been re-purposed
but still contains a valid label this can result in space no
longer owned by ZFS being zeroed. Prevent this by verifying
every label removed is intact before it's overwritten.
2) Address a small bug in zpool_do_labelclear() which prevented
labelclear from working on file vdevs. Only block devices support
BLKFLSBUF, try the ioctl() but when it's reported as unsupported
this should not be fatal.
3) Fix `zpool labelclear` so it can be run on vdevs which were
removed from the pool with `zpool remove`. Additionally, allow
intact but partial labels to be cleared as in the case of a failed
`zpool attach` or `zpool replace`.
4) Remove LABELCLEAR and LABELREAD variables for test cases.
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8500Closes#8373Closes#6261
This patch attempts to address some user concerns that have arisen
since errata 4 was introduced.
* The errata warning has been made less scary for users without
any encrypted datasets.
* The errata warning now clears itself without a pool reimport if
the bookmark_v2 feature is enabled and no encrypted datasets
exist.
* It is no longer possible to create new encrypted datasets without
enabling the bookmark_v2 feature, thus helping to ensure that the
errata is resolved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Issue ##8308
Closes#8504
Currently, there is an issue in the raw receive code where
raw receives are allowed to happen on top of previously
non-raw received datasets. This is a problem because the
source-side dataset doesn't know about how the blocks on
the destination were encrypted. As a result, any MAC in
the objset's checksum-of-MACs tree that is a parent of both
blocks encrypted on the source and blocks encrypted by the
destination will be incorrect. This will result in
authentication errors when we decrypt the dataset.
This patch fixes this issue by adding a new check to the
raw receive code. The code now maintains an "IVset guid",
which acts as an identifier for the set of IVs used to
encrypt a given snapshot. When a snapshot is raw received,
the destination snapshot will take this value from the
DRR_BEGIN payload. Non-raw receives and normal "zfs snap"
operations will cause ZFS to generate a new IVset guid.
When a raw incremental stream is received, ZFS will check
that the "from" IVset guid in the stream matches that of
the "from" destination snapshot. If they do not match, the
code will error out the receive, preventing the problem.
This patch requires an on-disk format change to add the
IVset guids to snapshots and bookmarks. As a result, this
patch has errata handling and a tunable to help affected
users resolve the issue with as little interruption as
possible.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#8308
The zpool iostat latency histograms (-w) has column names
'sync_queue' and 'async_queue', which do not match the man page, nor
the equivalent columns in average latency. Change the column
names to be 'syncq_wait' and 'asyncq_wait' to be consistent.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#8338
When `zpool iostat` fills the terminal the headers should be
printed again. `zpool iostat -n` can be used to suppress this.
If the command is not attached to a tty, headers will not be
printed so as to not break existing scripts.
Reviewed-by: Joshua M. Clulow <josh@sysmgr.org>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Damian Wojsław <damian@wojslaw.pl>
Closes#8235Closes#8262
Only display the full details of the vdev initialization state
in 'zpool status' output when requested with the -i option.
By default display '(initializing)' after vdevs when they are
being actively initialized. This is consistent with the
established precident of appending '(resilvering), etc' and
fits within the default 80 column terminal width making it
easy to read.
Additionally, updated the 'zpool initialize' documentation to
make it clear the options are mutually exclusive, but allow
duplicate options like all other zfs/zpool commands.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Tim Chase <tim@chase2k.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8230
PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
The verbose output of 'zpool list' was not correctly aligned due
to differences in the vdev name lengths. Minimally update the
code the correct the alignment using the same strategy employed
by 'zpool status'.
Missing dashes were added for the empty defaults columns, and
the vdev state is now printed for all vdevs.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7308Closes#8147
This patch adds a new slow I/Os (-s) column to zpool status to show the
number of VDEV slow I/Os. This is the number of I/Os that didn't
complete in zio_slow_io_ms milliseconds. It also adds a new parsable
(-p) flag to display exact values.
NAME STATE READ WRITE CKSUM SLOW
testpool ONLINE 0 0 0 -
mirror-0 ONLINE 0 0 0 -
loop0 ONLINE 0 0 0 20
loop1 ONLINE 0 0 0 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7756Closes#6885
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
Currently, if a resilver is triggered for any reason while an
existing one is running, zfs will immediately restart the existing
resilver from the beginning to include the new drive. This causes
problems for system administrators when a drive fails while another
is already resilvering. In this case, the optimal thing to do to
reduce risk of data loss is to wait for the current resilver to end
before immediately replacing the second failed drive, which allows
the system to operate with two incomplete drives for the minimum
amount of time.
This patch introduces the resilver_defer feature that essentially
does this for the admin without forcing them to wait and monitor
the resilver manually. The change requires an on-disk feature
since we must mark drives that are part of a deferred resilver in
the vdev config to ensure that we do not assume they are done
resilvering when an existing resilver completes.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: @mmaybee
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#7732
Historically, zpool status prints "(repairing)" for any drives that
have errors during a scrub:
NAME STATE READ WRITE CKSUM
mypool ONLINE 0 0 0
mirror-0 ONLINE 0 0 0
/tmp/file1 ONLINE 13 0 0 (repairing)
/tmp/file2 ONLINE 0 0 0
/tmp/file3 ONLINE 0 0 0
This was accidentally broken in "OpenZFS 9166 - zfs storage pool
checkpoint" (d2734cc). This patch adds it back in.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7779Closes#7978
Bandwidth and iops are average per second while *_wait are averages
per request for latency or, for queue depths, an instantaneous
measurement at the end of an interval (according to man zpool).
When calculating the first two it makes sense to do
x/interval_duration (x being the increase in total bytes or number of
requests over the duration of the interval, interval_duration in
seconds) to 'scale' from amount/interval_duration to amount/second.
But applying the same math for the latter (*_wait latencies/queue) is
wrong as there is no interval_duration component in the values (these
are time/requests to get to average_time/request or already an
absulute number).
This bug leads to the only correct continuous *_wait figures for both
latencies and queue depths from 'zpool iostat -l/q' being with
duration=1 as then the wrong math cancels itself (x/1 is a nop).
This removes temporal scaling from latency and queue depth figures.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Gregor Kopka <gregor@kopka.net>
Closes#7945Closes#7694
This change improve the handling of invalid filesystem properties when
specified at pool creation: this is useful when 'zpool create -n'
(dry run) is executed to detect invalid fs-level options (-O) before
the actual command is run.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7620Closes#7878
Allocation Classes add the ability to have allocation classes in a
pool that are dedicated to serving specific block categories, such
as DDT data, metadata, and small file blocks. A pool can opt-in to
this feature by adding a 'special' or 'dedup' top-level VDEV.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Alek Pinchuk <apinchuk@datto.com>
Reviewed-by: Håkan Johansson <f96hajo@chalmers.se>
Reviewed-by: Andreas Dilger <andreas.dilger@chamcloud.com>
Reviewed-by: DHE <git@dehacked.net>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Gregor Kopka <gregor@kopka.net>
Reviewed-by: Kash Pande <kash@tripleback.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#5182
argv[] gets modified during string parsing for input arguments. This
is reflected in the live process listing. Don't do that.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: DHE <git@dehacked.net>
Closes#7760
= Motivation
While dealing with another performance issue (see 126118f) we noticed
that we spend a lot of time in various places in the kernel when
constructing long nvlists. The problem is that when an nvlist is created
with the NV_UNIQUE_NAME set (which is the case most of the time), we do
a linear search through the whole list to ensure uniqueness for every
entry we add.
An example of the above scenario can be seen in the following
flamegraph, where more than have the time of the zfsdev_ioctl() is spent
on constructing nvlists. Flamegraph:
https://sdimitro.github.io/img/flame/sdimitro_snap_unmount3.svg
Adding a table to speed up lookups will help situations where we just
construct an nvlist (like the scenario above), in addition to regular
lookups and removals.
= What this patch does
In this diff we've implemented a hash-table on top of the nvlist code
that converts most nvlist operations from O(# number of entries) to
O(1)* (the start is for amortized time as the hash-table grows and
shrinks depending on the # of entries - plain lookup is strictly O(1)).
= Performance Analysis
To analyze the performance improvement I just used the setup from the
snapshot deletion issue mentioned above in the Motivation section.
Basically I created 10K filesystems with one snapshot each and then I
just used the API of libZFS_Core to pass down an nvlist of all the
snapshots to have them deleted. The reason I used my own driver program
was to have clean performance results of what actually happens in the
kernel. The flamegraphs and wall clock times mentioned below were
gathered from the start to the end of the driver program's run. Between
trials the testpool used was completely destroyed, the system was
rebooted and the testpool was completely recreated. The reason for this
dance was to get consistent results.
== Results (before patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 5.3
user 0.4
sys 2.3
[Trial 5]
real 8.2
user 0.4
sys 2.4
[Trial 6]
real 6.0
user 0.5
sys 2.3
```
== Results (after patch):
=== Sampling Flamegraphs
[Trial 1] https://sdimitro.github.io/img/flame/DLPX-53417/trial-Ae.svg
[Trial 2] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A2e.svg
[Trial 3] https://sdimitro.github.io/img/flame/DLPX-53417/trial-A3e.svg
=== Wall clock times (in seconds)
```
[Trial 4]
real 4.9
user 0.0
sys 0.9
[Trial 5]
real 3.8
user 0.0
sys 0.9
[Trial 6]
real 3.6
user 0.0
sys 0.9
```
== Analysis
The results between the trials are consistent so in this sections I will
only talk about the flamegraph results from trial-1 and the wall-clock
results from trial-4.
From trial-1 we can see that zfs_dev_ioctl() goes from 2,331 to 996
samples counts. Specifically, the samples from fnvlist_add_nvlist() and
spa_history_log_nvl() are almost gone (~500 & ~800 to 5 & 5 samples),
leaving zfs_ioc_destroy_snaps() to dominate most samples from
zfs_dev_ioctl().
From trial-4 we see that the user time dropped to 0 secods. I believe
the consistent 0.4 seconds before my patch was applied was due to my
driver program constructing the long nvlist of snapshots so it can pass
it to the kernel. As for the system time, the effect there is more clear
(2.3 down to 0.9 seconds).
Porting Notes:
* DATA_TYPE_DONTCARE case added to switch in fm_nvprintr() and
zpool_do_events_nvprint().
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/9580
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/b5eca7b1Closes#7748
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
1. Add a proc entry to display the pool's state:
$ cat /proc/spl/kstat/zfs/tank/state
ONLINE
This is done without using the spa config locks, so it will
never hang.
2. Fix 'zpool status' and 'zpool list -o health' output to print
"SUSPENDED" instead of "ONLINE" for suspended pools.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#7331Closes#7563
We want to be able to pass various settings during import/open of a
pool, which are not only related to rewind. Instead of adding a new
policy and duplicate a bunch of code, we should just rename
rewind_policy to a more generic term like load_policy.
For instance, we'd like to set spa->spa_import_flags from the nvlist,
rather from a flags parameter passed to spa_import as in some cases we
want those flags not only for the import case, but also for the open
case. One such flag could be ZFS_IMPORT_MISSING_LOG (as used in zdb)
which would allow zfs to open a pool when logs are missing.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://illumos.org/issues/9235
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/d2b1e44Closes#7532
Some work has been done lately to improve the debugability of the ZFS pool
load (and import) process. This includes:
7638 Refactor spa_load_impl into several functions
8961 SPA load/import should tell us why it failed
7277 zdb should be able to print zfs_dbgmsg's
To iterate on top of that, there's a few changes that were made to make the
import process more resilient and crash free. One of the first tasks during the
pool load process is to parse a config provided from userland that describes
what devices the pool is composed of. A vdev tree is generated from that config,
and then all the vdevs are opened.
The Meta Object Set (MOS) of the pool is accessed, and several metadata objects
that are necessary to load the pool are read. The exact configuration of the
pool is also stored inside the MOS. Since the configuration provided from
userland is external and might not accurately describe the vdev tree
of the pool at the txg that is being loaded, it cannot be relied upon to safely
operate the pool. For that reason, the configuration in the MOS is read early
on. In the past, the two configurations were compared together and if there was
a mismatch then the load process was aborted and an error was returned.
The latter was a good way to ensure a pool does not get corrupted, however it
made the pool load process needlessly fragile in cases where the vdev
configuration changed or the userland configuration was outdated. Since the MOS
is stored in 3 copies, the configuration provided by userland doesn't have to be
perfect in order to read its contents. Hence, a new approach has been adopted:
The pool is first opened with the untrusted userland configuration just so that
the real configuration can be read from the MOS. The trusted MOS configuration
is then used to generate a new vdev tree and the pool is re-opened.
When the pool is opened with an untrusted configuration, writes are disabled
to avoid accidentally damaging it. During reads, some sanity checks are
performed on block pointers to see if each DVA points to a known vdev;
when the configuration is untrusted, instead of panicking the system if those
checks fail we simply avoid issuing reads to the invalid DVAs.
This new two-step pool load process now allows rewinding pools accross
vdev tree changes such as device replacement, addition, etc. Loading a pool
from an external config file in a clustering environment also becomes much
safer now since the pool will import even if the config is outdated and didn't,
for instance, register a recent device addition.
With this code in place, it became relatively easy to implement a
long-sought-after feature: the ability to import a pool with missing top level
(i.e. non-redundant) devices. Note that since this almost guarantees some loss
of data, this feature is for now restricted to a read-only import.
Porting notes (ZTS):
* Fix 'make dist' target in zpool_import
* The maximum path length allowed by tar is 99 characters. Several
of the new test cases exceeded this limit resulting in them not
being included in the tarball. Shorten the names slightly.
* Set/get tunables using accessor functions.
* Get last synced txg via the "zfs_txg_history" mechanism.
* Clear zinject handlers in cleanup for import_cache_device_replaced
and import_rewind_device_replaced in order that the zpool can be
exported if there is an error.
* Increase FILESIZE to 8G in zfs-test.sh to allow for a larger
ext4 file system to be created on ZFS_DISK2. Also, there's
no need to partition ZFS_DISK2 at all. The partitioning had
already been disabled for multipath devices. Among other things,
the partitioning steals some space from the ext4 file system,
makes it difficult to accurately calculate the paramters to
parted and can make some of the tests fail.
* Increase FS_SIZE and FILE_SIZE in the zpool_import test
configuration now that FILESIZE is larger.
* Write more data in order that device evacuation take lonnger in
a couple tests.
* Use mkdir -p to avoid errors when the directory already exists.
* Remove use of sudo in import_rewind_config_changed.
Authored by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9075
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/619c0123Closes#7459
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
When the pool is suspended, record whether it was due to an I/O error or
due to MMP writes failing to succeed within the required time.
Change spa_suspended from uint8_t to zio_suspend_reason_t to store the
reason.
When userspace queries pool status via spa_tryimport(), report the
reason the pool was suspended in a new key,
ZPOOL_CONFIG_SUSPENDED_REASON.
In libzfs, when interpreting the returned config nvlist, report
suspension due to MMP with a new pool status enum value,
ZPOOL_STATUS_IO_FAILURE_MMP.
In status_callback(), which generates and emits the message when 'zpool
status' is executed, add a case to print an appropriate message for the
new pool status enum value.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#7296
get_format_prompt_string() and zpool_state_to_name() return
a string literal which is read-only, thus they should return
`const char*`.
zpool_get_prop_string() returns a non-const string after
successful nv-lookup, and returns a string literal otherwise.
Since this function is designed to be used for read-only purpose,
the return type should also be `const char*`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@osnexus.com>
Closes#7285
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#7133
The on-disk format for encrypted datasets protects not only
the encrypted and authenticated blocks themselves, but also
the order and interpretation of these blocks. In order to
make this work while maintaining the ability to do raw
sends, the indirect bps maintain a secure checksum of all
the MACs in the block below it along with a few other
fields that determine how the data is interpreted.
Unfortunately, the current on-disk format erroneously
includes some fields which are not portable and thus cannot
support raw sends. It is not possible to easily work around
this issue due to a separate and much smaller bug which
causes indirect blocks for encrypted dnodes to not be
compressed, which conflicts with the previous bug. In
addition, the current code generates incompatible on-disk
formats on big endian and little endian systems due to an
issue with how block pointers are authenticated. Finally,
raw send streams do not currently include dn_maxblkid when
sending both the metadnode and normal dnodes which are
needed in order to ensure that we are correctly maintaining
the portable objset MAC.
This patch zero's out the offending fields when computing
the bp MAC and ensures that these MACs are always
calculated in little endian order (regardless of the host
system's byte order). This patch also registers an errata
for the old on-disk format, which we detect by adding a
"version" field to newly created DSL Crypto Keys. We allow
datasets without a version (version 0) to only be mounted
for read so that they can easily be migrated. We also now
include dn_maxblkid in raw send streams to ensure the MAC
can be maintained correctly.
This patch also contains minor bug fixes and cleanups.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#6845Closes#6864Closes#7052
* Remove 'zfs snap' from zfs help message (OpenZFS sync)
* Update zfs(8) to suggest 'snap' can be used as an alias for 'snapshot'
* Enforce 80 columns limit in help messages
* Remove zfs_disable_dup_eviction from zfs-module-parameters(5)
* Expose zfs_scan_max_ext_gap as a kernel module parameter.
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7087
usr/src/uts/common/sys/fs/zfs.h
Change ZPROP_INVAL and ZPROP_CONT from macros to enum values. Clang
and GCC both prefer to use unsigned ints to store enums. That was
causing tautological comparison warnings (and likely eliminating
error handling code at compile time) whenever a zfs_prop_t or
zpool_prop_t was compared to ZPROP_INVAL or ZPROP_CONT. Making the
error flags be explicity enum values forces the enum types to be
signed.
ZPROP_INVAL was also compared against two different enum types. I
had to change its name to ZPOOL_PROP_INVAL whenever its compared to
a zpool_prop_t. There are still some places where ZPROP_INVAL or
ZPROP_CONT is compared to a plain int, in code that doesn't know
whether the int is storing a zfs_prop_t or a zpool_prop_t.
usr/src/uts/common/fs/zfs/spa.c
s/ZPROP_INVAL/ZPOOL_PROP_INVAL/
Authored by: Alan Somers <asomers@gmail.com>
Approved by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/8652
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c2de80dc74Closes#7061
Resolved unused variable warnings observed after restricting
-Wno-unused-but-set-variable to only libzfs and libzpool.
Reviewed-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6941
Fix a segfault when running 'zpool iostat -v 1' while adding
a VDEV.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#6748Closes#6872
наб
Paul Dagnelie
Allan Jude
Toomas Soome
Tony Hutter
Trevor Bautista
Matthew Ahrens
grembo
vermavipinkumar
Yuri Pankov
Colm
Andrea Gelmini
George Wilson
Thomas Lamprecht
Martin Matuška
Brian Behlendorf
sterlingjensen
Attila Fülöp
Andrew Sun
Cy Schubert
xdch47
Ryan Moeller
Arvind Sankar
Jorgen Lundman
George Amanakis
Philip Pokorny
Niklas Haas
Joao Carlos Mendes Luis
Romain Dolbeau
loli10K
Matthew Macy
Chunwei Chen
Matthew Macy
Ryan Moeller
John Gallagher
loli10K
JMoVS
Tom Caputi
TerraTech
Damian Wojsław
Don Brady
Gregor Kopka
DeHackEd
Serapheim Dimitropoulos
Low-power
Serapheim Dimitropoulos
Pavel Zakharov
Matthew Ahrens
Olaf Faaland
Tomohiro Kusumi
Chris Williamson
