Fix a leak of abd_t that manifested mostly when using
raidzN with at least as many columns as N (e.g. a
four-disk raidz2 but not a three-disk raidz2).
Sufficiently heavy raidz use would eventually run a system
out of memory.
Additionally:
* Switch abd_cache arena to FIRSTFIT, which empirically
improves perofrmance.
* Make abd_chunk_cache more performant and debuggable.
* Allocate the abd_zero_buf from abd_chunk_cache rather
than the heap.
* Don't try to reap non-existent qcaches in abd_cache arena.
* KM_PUSHPAGE->KM_SLEEP when allocating chunks from their
own arena
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: Sean Doran <smd@use.net>
Closes#12295
Compiling with gcc 11.1.0 produces three new warnings.
Change the code slightly to avoid them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12130Closes#12188Closes#12237
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
In all places except two spa_get_random() is used for small values,
and the consumers do not require well seeded high quality values.
Switch those two exceptions directly to random_get_pseudo_bytes()
and optimize spa_get_random(), renaming it to random_in_range(),
since it is not related to SPA or ZFS in general.
On FreeBSD directly map random_in_range() to new prng32_bounded() KPI
added in FreeBSD 13. On Linux and in user-space just reduce the type
used to uint32_t to avoid more expensive 64bit division.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12183
wmsum was designed exactly for cases like these with many updates
and rare reads. It allows to completely avoid atomic operations on
congested global variables.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12172
In zfs_znode_alloc we always hash inodes. If the
znode is unlinked, we do not need to hash it. This
fixes the problem where zfs_suspend_fs is doing zrele
(iput) in an async fashion, and zfs_resume_fs unlinked
drain processing will try to hash an inode that could
still be hashed, resulting in a panic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alan Somers <asomers@gmail.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9741Closes#11223Closes#11648Closes#12210
This mostly reverts "3537 want pool io kstats" commit of 8 years ago.
From one side this code using pool-wide locks became pretty bad for
performance, creating significant lock contention in I/O pipeline.
From another, there are more efficient ways now to obtain detailed
statistics, while this statistics is illumos-specific and much less
usable on Linux and FreeBSD, reported only via procfs/sysctls.
This commit does not remove KSTAT_TYPE_IO implementation, that may
be removed later together with already unused KSTAT_TYPE_INTR and
KSTAT_TYPE_TIMER.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12212
`getfsstat(2)` is used to retrieve the list of mounted file systems,
which libzfs uses when fetching properties like mountpoint, atime,
setuid, etc. The `mode` parameter may be `MNT_NOWAIT`, which uses
information in the VFS's cache, or `MNT_WAIT`, which effectively does a
`statfs` on every single mounted file system in order to fetch the most
up-to-date information. As far as I can tell, the only fields that
libzfs cares about are the filesystem's name, mountpoint, fstypename,
and mount flags. Those things are always updated on mount and unmount,
so they will always be accurate in the VFS's mount cache except in two
circumstances:
1) When a file system is busy unmounting
2) When a ZFS file system changes the value of a mount-overridable
property like atime or setuid, but doesn't remount the file system.
Right now that only happens when the property is changed by an
unprivileged user who has delegated authority to change the property
but not to mount the dataset. But perhaps libzfs could choose to do
it for other reasons in the future.
Switching to `MNT_NOWAIT` will greatly improve speed with no downside,
as long as we explicitly update the mount cache whenever we change a
mount-overridable property.
For comparison, Illumos gets this information using the native
`getmntany` and `getmntent` functions, which also use cached
information. The illumos function that would refresh the cache,
`resetmnttab`, is never called by libzfs.
And on GNU/Linux, `getmntany` and `getmntent` don't even communicate
with the kernel directly. They simply parse the file they are given,
which is usually /etc/mtab or /proc/mounts. Perhaps the implementation
of /proc/mounts is synchronous, ala MNT_WAIT; I don't know.
Sponsored-by: Axcient
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes: #12091
VFS_QUOTACTL(9) has been updated to allow each filesystem to indicate
whether it has changed the busy state of the mount. The filesystem
may still assume that its .vfs_quotactl entrypoint is always called
with the mount busied, but only needs to unbusy the mount (and clear
*mp_busy) if it does something that actually requires the mount to be
unbusied. It no longer needs to blindly copy-paste the UFS protocol
for calling vfs_unbusy(9) for the Q_QUOTAOFF and Q_QUOTAON commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jason Harmening <jason.harmening@gmail.com>
Closes#12052
For small objects the kernel's slab implementation is very fast and
space efficient. However, as the allocation size increases to
require multiple pages performance suffers. The SPL kmem cache
allocator was designed to better handle these large allocation
sizes. Therefore, on Linux the kmem_cache_* compatibility wrappers
prefer to use the kernel's slab allocator for small objects and
the custom SPL kmem cache allocator for larger objects.
This logic was effectively disabled for all architectures using
a non-4K page size which caused all kmem caches to only use the
SPL implementation. Functionally this is fine, but the SPL code
which calculates the target number of objects per-slab does not
take in to account that __vmalloc() always returns page-aligned
memory. This can result in a massive amount of wasted space when
allocating tiny objects on a platform using large pages (64k).
To resolve this issue we set the spl_kmem_cache_slab_limit cutoff
to 16K for all architectures.
This particular change does not attempt to update the logic used
to calculate the optimal number of pages per slab. This remains
an issue which should be addressed in a future change.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12152Closes#11429Closes#11574Closes#12150
Both were removed in 4fbdb10c7b ("remove
kmem_cache module parameter KMC_EXPIRE_AGE")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
The additional iter advance is incorrect, as copy_from_iter() has
already done the right thing. This will result in the following
warning being printed to the console as of the 5.12 kernel.
Attempted to advance past end of bvec iter
This change should have been included with #11378 when a
similar change was made on the read side.
Suggested-by: @siebenmann
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Issue #11378Closes#12041Closes#12155
Just like #12087, the set_acl signature changed with all the bolted-on
*userns parameters, which disabled set_acl usage, and caused #12076.
Turn zpl_set_acl into zpl_set_acl and zpl_set_acl_impl, and add a
new configure test for the new version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12076Closes#12093
Previous commit added accounting for geom mode, but not for dev.
In geom mode we actually have GEOM statistics, while in dev mode
additional accounting actually makes more sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12097
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12049
I looked for a bit, and couldn't find any documentation on
how to print all logged dbgmsg entries, just messages since
the DTrace probe started, until @allanjude kindly pointed me
toward the sysctl.
So let's add that note where the DTrace probe is mentioned for
FreeBSD, so other people can find it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12113
ZFS does not expect transient errors from crypto. For read they are
counted as checksum errors, while for write end up in panic. To not
panic on random low memory conditions retry ENOMEM errors in the OCF
wrapper function.
While there remove unneeded timeout and priority from msleep().
External-issue: https://reviews.freebsd.org/D30339
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12077
Linux changed the tmpfile() signature again in torvalds/linux@6521f89,
which in turn broke our HAVE_TMPFILE detection in configure.
Update that macro to include the new case, and change the signature of
zpl_tmpfile as appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12060Closes: #12087
FreeBSD historically has not cared about the xattr property; it was
always treated as xattr=on. With xattr=on, xattrs are stored as files
in a hidden xattr directory. With xattr=sa, xattrs are stored as
system attributes and get cached in nvlists during xattr operations.
This makes SA xattrs simpler and more efficient to manipulate. FreeBSD
needs to implement the SA xattr operations for feature parity with
Linux and to ensure that SA xattrs are accessible when migrated or
replicated from Linux.
Following the example set by Linux, refactor our existing extattr vnops
to split off the parts handling dir style xattrs, and add the
corresponding SA handling parts.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Commit d1d4769 takes into account the encryption key version to
decide if the local_mac could be zeroed out. However, this could lead
to failure mounting encrypted datasets created with intermediate
versions of ZFS encryption available in master between major releases.
In order to prevent this situation revert d1d4769 pending a more
comprehensive fix which addresses the mount failure case.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11294
Issue #12025
Issue #12300Closes#12033
Linux kernel commit 0f00b82e5413571ed225ddbccad6882d7ea60bc7 removes the
revalidate_disk() handler from struct block_device_operations. This
caused a regression, and this commit eliminates the call to it and the
assignment in the block_device_operations static handler assignment
code, when configure identifies that the kernel doesn't support that
API handler.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11967Closes#11977
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11972
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11994
zfs_log_create returns void, so there is no reason to cast its return
value to void at the call site.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11994
Quoting <linux/exportfs.h>:
> encode_fh() should return the fileid_type on success and on error
> returns 255 (if the space needed to encode fh is greater than
> @max_len*4 bytes). On error @max_len contains the minimum size (in 4
> byte unit) needed to encode the file handle.
ZFS was not setting max_len in the case where the handle was too
small. As a result of this, the `t_name_to_handle_at.c' example in
name_to_handle_at(2) did not work on ZFS.
zfsctl_fid() will itself set max_len if called with a fid that is too
small, so if we give zfs_fid() that behavior as well, the fix is quite
easy: if the handle is too small, just use a zero-size fid instead of
the handle.
Tested by running t_name_to_handle_at on a normal file, a directory, a
.zfs directory, and a snapshot.
Thanks-to: Puck Meerburg <puck@puckipedia.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Closes#11995
zp->z_lock is used in shared code for protecting projid and scantime.
We don't exercise these paths much if at all on FreeBSD, so have been
lucky enough not to have issues with the uninitialized locks so far.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#12003
Remove some extra whitespace.
Use pointer-typed asserts in Linux's znode cache destructor for more
info when debugging.
Simplify a couple of conversions from inode to znode when we already
have the znode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11974
Convert use of ASSERT() to ASSERT0(), ASSERT3U(), ASSERT3S(),
ASSERT3P(), and likewise for VERIFY(). In some cases it ended up
making more sense to change the code, such as VERIFY on nvlist
operations that I have converted to use fnvlist instead. In one
place I changed an internal struct member from int to boolean_t to
match its use. Some asserts that combined multiple checks with &&
in a single assert have been split to separate asserts, to make it
apparent which check fails.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11971
IS_XATTRDIR is never used.
v_count is only used in two places, one immediately followed by the
use of the real name, v_usecount.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#11973
This obeys the change in freebsd/freebsd-src@bce7ee9d4
External-issue: https://reviews.freebsd.org/D26980
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11947
This fixes /proc/sys/kernel/spl/hostid on kernels with mainline commit
32927393dc1ccd60fb2bdc05b9e8e88753761469 ("sysctl: pass kernel pointers
to ->proc_handler") ‒ 5.7-rc1 and up
The access_ok() check in copy_to_user() in proc_copyout_string() would
always fail, so all userspace reads and writes would fail with EINVAL
proc_dostring() strips only the final new-line,
but simple_strtoul() doesn't actually need a back-trimmed string ‒
writing "012345678 \n" is still allowed, as is "012345678zupsko", &c.
This alters what happens when an invalid value is written ‒
previously it'd get set to what-ever simple_strtoul() returned
(probably 0, thereby resetting it to default), now it does nothing
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11878Closes#11879
This change adds SIGSTOP and SIGTSTP handling to the issig function;
this mirrors its behavior on Solaris. This way, long running kernel
tasks can be stopped with the appropriate signals. Note that doing
so with ctrl-z on the command line doesn't return control of the tty
to the shell, because tty handling is done separately from stopping
the process. That can be future work, if people feel that it is a
necessary addition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #810
Issue #10843Closes#11801
It happens to trip over an assert but does not matter for correctness at
this time. Done for future proofing.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11884
After 3937ab20f zfsdev_get_state_impl can become zfsdev_get_state.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11833
SMACK needs to have the ZFS dentry security field setup before
SMACK's d_instantiate() hook is called as it requires functioning
'__vfs_getxattr()' calls to properly set the labels.
Fxes:
1) file instantiation properly setting the object label to the
subject's label
2) proper file labeling in a transmutable directory
Functions Updated:
1) zpl_create()
2) zpl_mknod()
3) zpl_mkdir()
4) zpl_symlink()
External-issue: https://github.com/cschaufler/smack-next/issues/1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: TerraTech <TerraTech@users.noreply.github.com>
Closes#11646Closes#11839
`kmem_alloc(size>PAGESIZE, KM_SLEEP)` is backed by `kmalloc()`, which
finds contiguous physical memory. If there isn't enough contiguous
physical memory available (e.g. due to physical page fragmentation), the
OOM killer will be invoked to make more memory available. This is not
ideal because processes may be killed when there is still plenty of free
memory (it just happens to be in individual pages, not contiguous runs
of pages). We have observed this when allocating the ~13KB `zfs_cmd_t`,
for example in `zfsdev_ioctl()`.
This commit changes the behavior of
`kmem_alloc(size>PAGESIZE, KM_SLEEP)` when there are insufficient
contiguous free pages. In this case we will find individual pages and
stitch them together using virtual memory. This is accomplished by
using `kvmalloc()`, which implements the described behavior by trying
`kmalloc(__GFP_NORETRY)` and falling back on `vmalloc()`.
The behavior of `kmem_alloc(KM_NOSLEEP)` is not changed; it continues to
use `kmalloc(GPF_ATOMIC | __GFP_NORETRY)`. This is because `vmalloc()`
may sleep.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11461
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
We have exclusive access to our zfsdev state object in this section
until it is invalidated by setting zs_minor to -1, so we can destroy
the state without taking a lock if we do the invalidation last, after
a member to ensure correct ordering.
While here, strengthen the assertions that zs_minor is valid when we
enter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11751
Other (all?) Linux filesystems seem to return -EPERM instead of -EACCESS
when trying to set FS_APPEND_FL or FS_IMMUTABLE_FL without the
CAP_LINUX_IMMUTABLE capability. This was detected by generic/545 test
in the fstest suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luis Henriques <henrix@camandro.org>
Closes#11791
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11775
It used to be required to pass a enum km_type to kmap_atomic() and
kunmap_atomic(), however this is no longer necessary and the wrappers
zfs_k(un)map_atomic removed these. This is confusing in the ABD code as
the struct abd_iter member iter_km no longer exists and the wrapper
macros simply compile them out.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11768
The BIO_MAX_PAGES macro is being retired in favor of a bio_max_segs()
function that implements the typical MIN(x,y) logic used throughout the
kernel for bounding the allocation, and also the new implementation is
intended to be signed-safe (which the former was not).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11765
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
Avoids tripping on asserts when doing pool recovery.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11739
Don't handle (incorrectly) kmem_zalloc() failure. With KM_SLEEP,
will never return NULL.
Free the data allocated for non-virtual kstats when deleting the object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11767
zhold() wraps igrab() on Linux, and igrab() may fail when the inode
is in the process of being deleted. This means zhold() must only be
called when a reference exists and therefore it cannot be deleted.
This is the case for all existing consumers so add a VERIFY and a
comment explaining this requirement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11704
To make use of zfs_refcount_held tunable it should be a module
parameter in open-zfs. Also, since the macros will auto-generate OS
specific tunables, removed the existing zfs_refcount_held reference
in module/os/freebsd/zfs/sysctl_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11753
Add parsing of the rewind options.
When I was upstreaming the change [1], I omitted the part where we
detect that the pool should be rewind. When the FreeBSD repo has
synced with the OpenZFS, this part of the code was removed.
[1] FreeBSD repo: 277f38abffc6a8160b5044128b5b2c620fbb970c
[2] OpenZFS repo: f2c027bd6a
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=254152
Originally reviewed by: tsoome, allanjude
Originally reviewed by: kevans (ok from high-level overview)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11730
Resolve some oddities in zfsdev_close() which could result in a
panic and were not present in the equivalent function for Linux.
- Remove unused definition ZFS_MIN_MINOR
- FreeBSD: Simplify zfsdev state destruction
- Assert zs_minor is valid in zfsdev_close
- Make locking around zfsdev state match Linux
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11720
This will allow platforms to implement it as they see fit, in particular
in a different manner than rrm locks.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are not very useful and hard to implement in the rms routine
the code is about to start using.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
1. even up ifdefs
2. drop the arguably useless teardown lock asserts -- nothing else
checks for it
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
zil_replaying(zil, tx) has the side-effect of informing the ZIL that an
entry has been replayed in the (still open) tx. The ZIL uses that
information to record the replay progress in the ZIL header when that
tx's txg syncs.
ZPL log entries are not idempotent and logically dependent and thus
calling zil_replaying() is necessary for correctness.
For ZVOLs the question of correctness is more nuanced: ZVOL logs only
TX_WRITE and TX_TRUNCATE, both of which are idempotent. Logical
dependencies between two records exist only if the write or discard
request had sync semantics or if the ranges affected by the records
overlap.
Thus, at a first glance, it would be correct to restart replay from
the beginning if we crash before replay completes. But this does not
address the following scenario:
Assume one log record per LWB.
The chain on disk is
HDR -> 1:W(1, "A") -> 2:W(1, "B") -> 3:W(2, "X") -> 4:W(3, "Z")
where N:W(O, C) represents log entry number N which is a TX_WRITE of C
to offset A.
We replay 1, 2 and 3 in one txg, sync that txg, then crash.
Bit flips corrupt 2, 3, and 4.
We come up again and restart replay from the beginning because
we did not call zil_replaying() during replay.
We replay 1 again, then interpret 2's invalid checksum as the end
of the ZIL chain and call replay done.
The replayed zvol content is "AX".
If we had called zil_replaying() the HDR would have pointed to 3
and our resumed replay would not have replayed anything because
3 was corrupted, resulting in zvol content "BX".
If 3 logically depends on 2 then the replay corrupted the ZVOL_OBJ's
contents.
This patch adds the zil_replaying() calls to the replay functions.
Since the callbacks in the replay function need the zilog_t* pointer
so that they can call zil_replaying() we open the ZIL while
replaying in zvol_create_minor(). We also verify that replay has
been done when on-demand-opening the ZIL on the first modifying
bio.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11667
ZFS_READONLY represents the "DOS R/O" attribute.
When that flag is set, we should behave as if write access
were not granted by anything in the ACL. In particular:
We _must_ allow writes after opening the file r/w, then
setting the DOS R/O attribute, and writing some more.
(Similar to how you can write after fchmod(fd, 0444).)
Restore these semantics which were lost on FreeBSD when refactoring
zfs_write. To my knowledge Linux does not actually expose this flag,
but we'll need it to eventually so I've added the supporting checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11693
When populating a ZIL destination buffer ensure it is always
zeroed before its contents are constructed.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11687
The spl_kmem_alloc showed up in some flamegraphs in a single-threaded
4k sync write workload at 85k IOPS on an
Intel(R) Xeon(R) Silver 4215 CPU @ 2.50GHz.
Certainly not a huge win but I believe the change is clean and
easy to maintain down the road.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11666
The function has three similar pieces of code: for read-behind pages,
requested pages and read-ahead pages. All three pieces had an
assert to ensure that the page is not mapped. Later the assert was
relaxed to require that the page is not mapped for writing. But that
was done in two places out of three. This change fixes the third piece,
read-ahead.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11654
The struct bio member bi_disk was moved underneath a new member named
bi_bdev. So all attempts to reference bio->bi_disk need to now become
bio->bi_bdev->bd_disk.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
On Linux increase the maximum allowed size of the src nvlist which
can be passed to the /dev/zfs ioctl. Originally, this was set
to a maximum of KMALLOC_MAX_SIZE (4M) because it was kmalloc'd.
Since that time it's been converted to a vmalloc so that's no
longer a hard limit, and it's desirable for `zfs send/recv` to
allow larger nvlists so more snapshots can be sent at once.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6572Closes#11638
Making uio_impl.h the common header interface between Linux and FreeBSD
so both OS's can share a common header file. This also helps reduce code
duplication for zfs_uio_t for each OS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11622
First, the crypto request completion handler contains a bug in that it
fails to reset fs_done correctly after the request is completed. This
is only a problem for asynchronous drivers. Second, some hardware
drivers have input constraints which ZFS does not satisfy. For
instance, ccp(4) apparently requires the AAD length for AES-GCM to be a
multiple of the cipher block size, and with qat(4) the AES-GCM AAD
length may not be longer than 240 bytes. FreeBSD's generic crypto
framework doesn't have a mechanism to automatically fall back to a
software implementation if a hardware driver cannot process a request,
and ZFS does not tolerate such errors.
The plan is to implement such a fallback mechanism, but with FreeBSD
13.0 approaching we should simply disable the use hardware drivers for
now.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#11612
Remove function that become unused after refactoring in
e2af2acce3.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Libby <rlibby@FreeBSD.org>
Closes#11614
zfs_znode_update_vfs is a more platform-agnostic name than
zfs_inode_update. Besides that, the function's prototype is moved to
include/sys/zfs_znode.h as the function is also used in common code.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ka Ho Ng <khng300@gmail.com>
Sponsored by: The FreeBSD Foundation
Closes#11580
The first time through the loop prevdb and prevhdl are NULL. They
are then both set, but only prevdb is checked. Add an ASSERT to
make it clear that prevhdl must be set when prevdb is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kleber <klebertarcisio@yahoo.com.br>
Closes#10754Closes#11575
`__vdev_disk_physio()` uses `abd_nr_pages_off()` to allocate a bio with
a sufficient number of iovec's to process this zio (i.e.
`nr_iovecs`/`bi_max_vecs`). If there are not enough iovec's in the bio,
then additional bio's will be allocated. However, this is a sub-optimal
code path. In particular, it requires several abd calls (to
`abd_nr_pages_off()` and `abd_bio_map_off()`) which will have to walk
the constituents of the ABD (the pages or the gang children) because
they are looking for offsets > 0.
For gang ABD's, `abd_nr_pages_off()` returns the number of iovec's
needed for the first constituent, rather than the sum of all
constituents (within the requested range). This always under-estimates
the required number of iovec's, which causes us to always need several
bio's. The end result is that `__vdev_disk_physio()` is usually O(n^2)
for gang ABD's (and occasionally O(n^3), when more than 16 bio's are
needed).
This commit fixes `abd_nr_pages_off()`'s handling of gang ABD's, to
correctly determine how many iovec's are needed, by adding up the number
of iovec's for each of the gang children in the requested range.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11536
There is a race condition in zfs_zrele_async when we are checking if
we would be the one to evict an inode. This can lead to a txg sync
deadlock.
Instead of calling into iput directly, we attempt to perform the atomic
decrement ourselves, unless that would set the i_count value to zero.
In that case, we dispatch a call to iput to run later, to prevent a
deadlock from occurring.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11527Closes#11530
In order for cppcheck to perform a proper analysis it needs to be
aware of how the sources are compiled (source files, include
paths/files, extra defines, etc). All the needed information is
available from the Makefiles and can be leveraged with a generic
cppcheck Makefile target. So let's add one.
Additional minor changes:
* Removing the cppcheck-suppressions.txt file. With cppcheck 2.3
and these changes it appears to no longer be needed. Some inline
suppressions were also removed since they appear not to be
needed. We can add them back if it turns out they're needed
for older versions of cppcheck.
* Added the ax_count_cpus m4 macro to detect at configure time how
many processors are available in order to run multiple cppcheck
jobs. This value is also now used as a replacement for nproc
when executing the kernel interface checks.
* "PHONY =" line moved in to the Rules.am file which is included
at the top of all Makefile.am's. This is just convenient becase
it allows us to use the += syntax to add phony targets.
* One upside of this integration worth mentioning is it now allows
`make cppcheck` to be run in any directory to check that subtree.
* For the moment, cppcheck is not run against the FreeBSD specific
kernel sources. The cppcheck-FreeBSD target will need to be
implemented and testing on FreeBSD to support this.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Identical condition and return expression 'rc', return value is
always 0.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
The ASSERT that the passed pointer isn't NULL appears after the
pointer has already been dereferenced. Remove the redundant check.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Like any other thread created by thread_create() we need to call
thread_exit() to properly clean it up. In particular, this ensures the
tsd hash for the thread is cleared.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11512
Set VIRF_MOUNTPOINT flag on snapshot mountpoint.
Authored-by: Mateusz Guzik <mjg@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11458
As part of commit 1c2358c1 the custom uio_prefaultpages() code
was removed in favor of using the generic kernel provided
iov_iter_fault_in_readable() interface. Unfortunately, it
turns out that up until the Linux 4.7 kernel the function would
only ever fault in the first iovec of the iov_iter. The result
being uiomove_iov() may hang waiting for the page.
This commit effectively restores the custom uio_prefaultpages()
pages code for Linux 4.9 and earlier kernels which contain the
troublesome version of iov_iter_fault_in_readable().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11463Closes#11484
In FreeBSD the struct uio was just a typedef to uio_t. In order to
extend this struct, outside of the definition for the struct uio, the
struct uio has been embedded inside of a uio_t struct.
Also renamed all the uio_* interfaces to be zfs_uio_* to make it clear
this is a ZFS interface.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11438
The `abd_get_offset_*()` routines create an abd_t that references
another abd_t, and doesn't allocate any pages/buffers of its own. In
some workloads, these routines may be called frequently, to create many
abd_t's representing small pieces of a single large abd_t. In
particular, the upcoming RAIDZ Expansion project makes heavy use of
these routines.
This commit adds the ability for the caller to allocate and provide the
abd_t struct to a variant of `abd_get_offset_*()`. This eliminates the
cost of allocating the abd_t and performing the accounting associated
with it (`abdstat_struct_size`). The RAIDZ/DRAID code uses this for
the `rc_abd`, which references the zio's abd. The upcoming RAIDZ
Expansion project will leverage this infrastructure to increase
performance of reads post-expansion by around 50%.
Additionally, some of the interfaces around creating and destroying
abd_t's are cleaned up. Most significantly, the distinction between
`abd_put()` and `abd_free()` is eliminated; all types of abd_t's are
now disposed of with `abd_free()`.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #8853Closes#11439
Virtuozzo 7 kernels starting 3.10.0-1127.18.2.vz7.163.46
have the following configuration:
* no HAVE_VFS_RW_ITERATE
* HAVE_VFS_DIRECT_IO_ITER_RW_OFFSET
=> let's add implementation of zpl_direct_IO() via
zpl_aio_{read,write}() in this case.
https://bugs.openvz.org/browse/OVZ-7243
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Closes#11410Closes#11411
As of 5.11 the blk_register_region() and blk_unregister_region()
functions have been retired. This isn't a problem since add_disk()
has implicitly allocated minor numbers for a very long time.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Both revalidate_disk_size() and revalidate_disk() have been removed.
Functionally this isn't a problem because we only relied on these
functions to call zvol_revalidate_disk() for us and to perform any
additional handling which might be needed for that kernel version.
When neither are available we know there's no additional handling
needed and we can directly call zvol_revalidate_disk().
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The bd_contains member was removed from the block_device structure.
Callers needing to determine if a vdev is a whole block device should
use the new bdev_whole() wrapper. For older kernels we provide our
own bdev_whole() wrapper which relies on bd_contains for compatibility.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The generic IO accounting functions have been removed in favor of the
bio_start_io_acct() and bio_end_io_acct() functions which provide a
better interface. These new functions were introduced in the 5.8
kernels but it wasn't until the 5.11 kernel that the previous generic
IO accounting interfaces were removed.
This commit updates the blk_generic_*_io_acct() wrappers to provide
and interface similar to the updated kernel interface. It's slightly
different because for older kernels we need to pass the request queue
as well as the bio.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The lookup_bdev() function has been updated to require a dev_t
be passed as the second argument. This is actually pretty nice
since the major number stored in the dev_t was the only part we
were interested in. This allows to us avoid handling the bdev
entirely. The vdev_lookup_bdev() wrapper was updated to emulate
the behavior of the new lookup_bdev() for all supported kernels.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Commit 1c2358c12 restructured this code and introduced a warning
about the variable maybe not being initialized. This cannot happen
with the updated code but we should initialize the variable anyway
to silence the warning.
zpl_file.c: In function ‘zpl_iter_write’:
zpl_file.c:324:9: warning: ‘count’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11373
There's no need to call iov_iter_advance() in zpl_iter_read().
This was preserved from the previous code where it wasn't needed
but also didn't cause any problems. Now that the iter functions
also handle pipes that's no longer the case. When fully reading a
pipe buffer iov_iter_advance() may results in the pipe buf release
function being called which will not be registered resulting in
a NULL dereference.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11375Closes#11378
Commit 59b68723 added a configure check for 5.10, which removed
revalidate_disk(), and conditionally replaced it's usage with a call to
the new revalidate_disk_size() function. However, the old function also
invoked the device's registered callback, in our case
zvol_revalidate_disk(). This commit adds a call to zvol_revalidate_disk()
in zvol_update_volsize() to make sure the code path stays the same.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Closes#11358
As of the 5.10 kernel the generic splice compatibility code has been
removed. All filesystems are now responsible for registering a
->splice_read and ->splice_write callback to support this operation.
The good news is the VFS provided generic_file_splice_read() and
iter_file_splice_write() callbacks can be used provided the ->iter_read
and ->iter_write callback support pipes. However, this is currently
not the case and only iovecs and bvecs (not pipes) are ever attached
to the uio structure.
This commit changes that by allowing full iov_iter structures to be
attached to uios. Ever since the 4.9 kernel the iov_iter structure
has supported iovecs, kvecs, bvevs, and pipes so it's desirable to
pass the entire thing when possible. In conjunction with this the
uio helper functions (i.e uiomove(), uiocopy(), etc) have been
updated to understand the new UIO_ITER type.
Note that using the kernel provided uio_iter interfaces allowed the
existing Linux specific uio handling code to be simplified. When
there's no longer a need to support kernel's older than 4.9, then
it will be possible to remove the iovec and bvec members from the
uio structure and always use a uio_iter. Until then we need to
maintain all of the existing types for older kernels.
Some additional refactoring and cleanup was included in this change:
- Added checks to configure to detect available iov_iter interfaces.
Some are available all the way back to the 3.10 kernel and are used
when available. In particular, uio_prefaultpages() now always uses
iov_iter_fault_in_readable() which is available for all supported
kernels.
- The unused UIO_USERISPACE type has been removed. It is no longer
needed now that the uio_seg enum is platform specific.
- Moved zfs_uio.c from the zcommon.ko module to the Linux specific
platform code for the zfs.ko module. This gets it out of libzfs
where it was never needed and keeps this Linux specific code out
of the common sources.
- Removed unnecessary O_APPEND handling from zfs_iter_write(), this
is redundant and O_APPEND is already handled in zfs_write();
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11351
vfs.zfs.arc_no_grow_shift has an invalid type (15) and this causes
py-sysctl to format it as a bytearray when it should be an integer.
"U" is not a valid format, it should be "I" and the type should match
the variable type, int. We can return EINVAL if the value is set below
zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11318
Resolve an uninitialized variable warning when compiling.
In function ‘zfs_domount’:
warning: ‘root_inode’ may be used uninitialized in this
function [-Wmaybe-uninitialized]
sb->s_root = d_make_root(root_inode);
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11306
ZFS currently doesn't react to hotplugging cpu or memory into the
system in any way. This patch changes that by adding logic to the ARC
that allows the system to take advantage of new memory that is added
for caching purposes. It also adds logic to the taskq infrastructure
to support dynamically expanding the number of threads allocated to a
taskq.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11212
With both abd_size and abd_nents being uint_t it makes no sense for
abd_chunkcnt_for_bytes() to return size_t. Random mix of different
types used to count chunks looks bad and makes compiler more difficult
to optimize the code.
In particular on FreeBSD this change allows compiler to completely
optimize out abd_verify_scatter() when built without debug, removing
pointless 64-bit division and even more pointless empty loop.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11279
When sending raw encrypted datasets the user space accounting is present
when it's not expected to be. This leads to the subsequent mount failure
due a checksum error when verifying the local mac.
Fix this by clearing the OBJSET_FLAG_USERACCOUNTING_COMPLETE and reset
the local mac. This allows the user accounting to be correctly updated
on first mount using the normal upgrade process.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10523Closes#11221
- Don't leave fstrans set when passed a snapshot
- Don't remove minor if volmode already matches new value
- (FreeBSD) Wait for GEOM ops to complete before trying
remove (at create time GEOM will be "tasting" in parallel)
- (FreeBSD) Don't leak zvol_state_lock on open if zv == NULL
- (FreeBSD) Don't try to unlock zv->zv_state lock if zv == NULL
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11199
The ZFS_ENTER/ZFS_EXIT/ZFS_VERFY_ZP macros should not be used
in the Linux zpl_*.c source files. They return a positive error
value which is correct for the common code, but not for the Linux
specific kernel code which expects a negative return value. The
ZPL_ENTER/ZPL_EXIT/ZPL_VERFY_ZP macros should be used instead.
Furthermore, the ZPL_EXIT macro has been updated to not call the
zfs_exit_fs() function. This prevents a possible deadlock which
can occur when a snapshot is automatically unmounted because the
zpl_show_devname() must never wait on in progress automatic
snapshot unmounts.
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11169Closes#11201
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
The custom zpl_show_devname() helper should translate spaces in
to the octal escape sequence \040. The getmntent(2) function
is aware of this convention and properly translates the escape
character back to a space when reading the fsname.
Without this change the `zfs mount` and `zfs unmount` commands
incorrectly detect when a dataset with a name containing spaces
is mounted.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11182Closes#11187
The microzap hash can sometimes be zero for single digit snapnames.
The zap cursor can then have a serialized value of two (for . and ..),
and skip the first entry in the avl tree for the .zfs/snapshot directory
listing, and therefore does not return all snapshots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Tony Perkins <tperkins@datto.com>
Closes#11039
The field is yet another leftover from unsupported zfs_znode_move.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11186
We can consolidate the unlocking procedure into one place by starting
with drop_suspend set to B_FALSE and moving the open count check up.
While here, a little code cleanup. Match the out labels between
zvol_geom_open and zvol_cdev_open, and add a missing period in some
comments.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
zvol_first_open can fail with EINTR if spa_namespace_lock is not held
and cannot be taken without waiting.
Apply the same logic that was done for zvol_geom_open to take
spa_namespace_lock if not already held on first open in zvol_cdev_open.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
The oid comes from the znode we are already passing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11176
Check if the ZVOL has been written before calling zil_async_to_sync.
The ZIL will be opened on the first write, not earlier.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11152
spa_config_load() passes NULL into resid when doing zfs_file_read().
This would trip over when vfs.zfs.autoimport_disable=0.
Sponsored by: The FreeBSD Foundation
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ka Ho Ng <khng@freebsdfoundation.org>
Closes#11149
SET_ERROR is useful to trace errors, so use it where the errors occur
rather than factored out to the end of a function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11146
A new function was added named revalidate_disk_size() and the old
revalidate_disk() appears to have been deprecated. As the only ZFS
code that calls this function is zvol_update_volsize, swapping the
old function call out for the new one should be all that is required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel 5.10 removed check_disk_change() in favor of callers using
the faster bdev_check_media_change() instead, and explicitly forcing
bdev revalidation when they desire that behavior. To preserve prior
behavior, I have wrapped this into a zfs_check_media_change() macro
that calls an inline function for the new API that mimics the old
behavior when check_disk_change() doesn't exist, and just calls
check_disk_change() if it exists.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel commit 2b0d3d3e4fcfb brought in some changes to the struct
percpu_ref structure that moves most of its fields into a member
struct named "data" of type struct percpu_ref_data. This includes
the "count" member which is updated by vdev_blkg_tryget(), so update
this function to chase the API change, and detect it via configure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Move zfs_get_data() in to platform-independent code. The only
platform-specific aspect of it is the way we release an inode
(Linux) / vnode_t (FreeBSD). I am not aware of a platform that
could be supported by ZFS that couldn't implement zfs_rele_async
itself. It's sibling zvol_get_data already is platform-independent.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#10979
The zfs_holey() and zfs_access() functions can be made common
to both FreeBSD and Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11125
zvol private data is supposed to be nulled by zvol_clear_private before
zvol_free is called as an indicator that the zvol is going away.
Implement zvol_clear_private for volmode=dev.
Assert that zvol_clear_private has been called before zvol_free.
Check that zvol_clear_private has not been called when updating
volsize. If it has, fail with ENXIO.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Make sure to free doi in zvol_create_minor impl when make_dev_s fails.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
We fall back to a default volmode and continue when looking up a zvol's
volmode property fails. After this we should set the error to 0 to
ensure we take the success paths in the out section.
While here, make sure we only log that the zvol was created on success.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Nonfunctional changes for readability and consistency.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
zvol_geom_close gets a count of the number of close operations to do.
Make sure we're always using this count to check if this will be the
last close operation performed on the zvol.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Using more specific assert variants gives better messages on failure.
No functional change.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
AT_BENEATH was merged to stable/12, where kern_unlinkat takes a
non-const path. DECONST the path passed to kern_unlinkat in the
case where AT_BENEATH is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11139
The original xuio zero copy functionality has always been unused
on Linux and FreeBSD. Remove this disabled code to avoid any
confusion and improve readability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11124
Refer to the correct section or alternative for FreeBSD and Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11132
ZFS always waits for the write completion before flushing the cache.
That is why it does not require explicit ordering fences around it,
which are pretty difficult to implement for NVMe, since one has no
internal concept of strict request ordering.
This was already removed from FreeBSD once, but got resurrected
by mistake during OpenZFS merge.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11130
The port removed provisions for zfs_znode_move but the cleanup missed
this bit. To quote the original:
[snip]
list_insert_tail(&zfsvfs->z_all_znodes, zp);
membar_producer();
/*
* Everything else must be valid before assigning z_zfsvfs makes the
* znode eligible for zfs_znode_move().
*/
zp->z_zfsvfs = zfsvfs;
[/snip]
In the current code it is immediately followed by unlock which issues
the same fence, thus plays no role in correctness.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11115
The allocator does not provide the functionality to begin with.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11114
These kstats are often expensive to compute so we want to avoid them
unless specifically requested.
The following kstats are affected by this change:
kstat.zfs.${pool}.multihost
kstat.zfs.${pool}.misc.state
kstat.zfs.${pool}.txgs
kstat.zfs.misc.fletcher_4_bench
kstat.zfs.misc.vdev_raidz_bench
kstat.zfs.misc.dbufs
kstat.zfs.misc.dbgmsg
In FreeBSD 13, sysctl(8) has been updated to still list the
names/description/type of skipped sysctls so they are still
discoverable.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11099
The zfs_fsync, zfs_read, and zfs_write function are almost identical
between Linux and FreeBSD. With a little refactoring they can be
moved to the common code which is what is done by this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11078
zfs_onexit_os.c was not deleted when it was removed from the build
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11079
Otherwise lookup can fail with EOPNOTSUPP or panic.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11066
The 32-bit counter eventually wraps to 0 which is a sentinel for invalid
id.
Make it 64-bit on LP64 platforms and 0-check otherwise.
Note: Linux counterpart uses id stored per queue instead of a global.
I did not check going that way is feasible with the goal being the
minimal fix doing the job.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11059
The acltype property is currently hidden on FreeBSD and does not
reflect the NFSv4 style ZFS ACLs used on the platform. This makes it
difficult to observe that a pool imported from FreeBSD on Linux has a
different type of ACL that is being ignored, and vice versa.
Add an nfsv4 acltype and expose the property on FreeBSD.
Make the default acltype nfsv4 on FreeBSD.
Setting acltype to an unhanded style is treated the same as setting
it to off. The ACLs will not be removed, but they will be ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10520
In FreeBSD, there are three compile environments that are supported:
user land, the kernel and the bootloader / standalone. Adjust the
headers to compile in the standalone environment. Limit kernel-only
items from view when _STANDALONE is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Warner Losh <imp@FreeBSD.org>
Closes#10998
FreeBSD had this value tunable before the switch to the new OpenZFS.
The tunable name has changed, breaking legacy compat.
Restore legacy compat for this tunable, properly expose the tunable
with the new name on all platforms, and document it in
zfs-module-parameters(5).
While here, clean up the documentation for zfetch_max_distance a bit.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11038
The value of zp is used without having been initialized under some
conditions. Initialize the pointer to NULL.
Add a regression test case using chown in acl/posix. However, this is
not enough because the setup sets xattr=sa, which means zfs_setattr_dir
will not be called. Create a second group of acl tests in acl/posix-sa
duplicating the acl/posix tests with symlinks, and remove xattr=sa from
the original acl/posix tests. This provides more coverage for the
default xattr=on code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10043Closes#11025
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
With procfs_list kstats implemented for FreeBSD, dbufs are now exposed
as kstat.zfs.misc.dbufs.
On FreeBSD, dbufstats can use the sysctl instead of procfs when no
input file has been given.
Enable the dbufstats tests on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11008
Code cleanup. Sort includes, remove duplicates, and drop
some extra blank lines in kmod_core.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11000
We were missing an include for kernel FPU functions, breaking the build
on FreeBSD 12.1-RELEASE. This was apparently being pulled in from
elsewhere on stable/12 and head.
Sorted the other includes in these files while here.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11005
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
The kernel seq_read() helper function expects ->next() to update
the passed position even there are no more entries. Failure to
do so results in the following warning being logged.
seq_file: buggy .next function procfs_list_seq_next [spl]
did not update position index
Functionally there is no issue with the way procfs_list_seq_next()
is implemented and the warning is harmless. However, we want to
silence this some what scary incorrect warning. This commit
updates the Linux procfs code to advance the position even for
the last entry.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10984Closes#10996
The request number is out of bounds of the platform table.
Subtract the starting offset to get the correct subscript.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10994
When an invalid incremental send is requested where the "to" ds is
before the "from" ds, make sure to drop the reference to the pool
and the dataset before returning the error.
Add an assert on FreeBSD to make sure we don't hold any locks after
returning from an ioctl.
Add some test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10919
With PREEMPTION=y and BLK_CGROUP=y preempt_schedule_notrace() is being
used on arm64 which is a GPL-only function and hence the build of the
DKMS kernel module fails.
Fix that by redefining preempt_schedule_notrace() to preempt_schedule()
which should be safe as long as tracing is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Closes#8545Closes#9948Closes#10416Closes#10973
Address some unused value and control flow issues flagged by Coverity.
Unreachable code is pruned and unused values are avoided.
Some scattered sections are reordered for coherence.
We can assume kmem_alloc(n, KM_SLEEP) doesn't fail, so there is no need
to check if it returned NULL. The allocated memory doesn't need to be
zeroed, other than the last iovec (the MAC).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10884
The procfs_list interface is required by several kstats. Implement
this functionality for FreeBSD to provide access to these kstats.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10890
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10899
In commit cd32b4f5b7 ("Fix a deadlock in the FreeBSD getpages VOP") I
introduced a bug while porting the patch originally committed to
FreeBSD: the rangelock pointer may be NULL if the try operation failed,
so we must avoid calling zfs_rangelock_unlock() in that case.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reported-by: Steve Wills <swills@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10519Closes#10960
Without this, the sysctl system calls will acquire a global lock before
invoking the handler. This is noticeable in some situations when
running top(1). The global lock is mostly vestigal but continues to see
some use and so contention is still a problem; until the default sense
of the MPSAFE flag changes, we have to annotate each and every handler.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10836
This is in preparation for some functional changes.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10950
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
When expanding a device zfs needs to rescan the partition table to
get the correct size. This can only happen when we're in the kernel
and requires the device to be closed. As part of the rescan, udev is
notified and the device links are removed and recreated. This leave a
window where the vdev code may try to reopen the device before udev
has recreated the link. If that happens, then the pool may end up in
a suspended state.
To correct this, we leverage the BLKPG_RESIZE_PARTITION ioctl which
allows the partition information to be modified even while it's in use.
This ioctl also does not remove the device link associated with the zfs
data partition so it eliminates the race condition that can occur in
the kernel.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#10897
https://reviews.freebsd.org/D26346
Do not copy vp into f_data for DTYPE_VNODE files. The vnode pointer is
already stored in f_vnode. Use that so f_data can be reused.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10929
In zpl_mount_impl, there is:
dmu_objset_hold ; returns with pool & ds held
dsl_pool_rele
sget
dsl_dataset_rele
As spelled out in the "DSL Pool Configuration Lock" in dsl_pool.c,
this requires a long hold.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10936
Prefer acltype=off|posix, retaining the old names as aliases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10918
Use ZFS_ENTER and ZFS_EXIT to protect datasets while their mount
devname is being retrieved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10892Closes#10927
The lock is taken all the time and as a regular read-write lock
avoidably serves as a mount point-wide contention point.
This forward ports FreeBSD revision r357322.
To quote aforementioned commit:
Sample result doing an incremental -j 40 build:
before: 173.30s user 458.97s system 2595% cpu 24.358 total
after: 168.58s user 254.92s system 2211% cpu 19.147 total
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#10896
We only need the kernel interfaces in crypto, not the device node in
cryptodev.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10901
There are a number of places where cv_?_sig is used simply for
accounting purposes but the surrounding code has no ability to
cope with actually receiving a signal. On FreeBSD it is possible
to send signals to individual kernel threads so this could
enable undesirable behavior.
This patch adds routines on Linux that will do the same idle
accounting as _sig without making the task interruptible. On
FreeBSD cv_*_idle are all aliases for cv_*
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10843
Added comments in following files
with links to Illumos manual pages:
./module/avl/avl.c
./module/nvpair/nvpair.c
./module/os/linux/spl/spl-kstat.c
./module/os/freebsd/spl/spl_kstat.c
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Spencer Kinny <spencerkinny1995@gmail.com>
Closes#5113Closes#10859
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10867
Moving spa_stats added the additional burden of supporting
KSTAT_TYPE_IO.
spa_state_addr will always return a valid value regardless of
the value of 'n'. On FreeBSD this will cause an infinite loop
as it relies on the raw ops addr routine to indicate that there
is no more data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10860
Allow to rename file systems without remounting if it is possible.
It is possible for file systems with 'mountpoint' property set to
'legacy' or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even
mounted back.
This introduces layering violation, as we need to update
'f_mntfromname' field in statfs structure related to mountpoint (for
the dataset we are renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even
cleaner way - in ZFS-only configuration root file system is ZFS file
system with 'mountpoint' property set to 'legacy'. If root dataset is
named system/rootfs, we can snapshot it (system/rootfs@upgrade), clone
it (system/oldrootfs), update FreeBSD and if it doesn't boot we can
boot back from system/oldrootfs and rename it back to system/rootfs
while it is mounted as /. Before it was not possible, because
unmounting / was not possible.
Authored by: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: Matt Macy <mmacy@freebsd.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10839
SECLABEL is undefined on FreeBSD and should be pruned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10847
FreeBSD's previous ZFS implemented INGLOBALZONE(thread) as
(!jailed((thread)->td_ucred)) and passed curthread to INGLOBALZONE.
We pass curproc instead of curthread, so we can achieve the same effect
with (!jailed((proc)->p_ucred)). The implementation is trivial enough
to fit on a single line in a define. We don't really need a whole
separate function for something that's already macros all the way down.
Eliminate in_globalzone.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10851
Initially it was considered simplest to stub out all
of the functions on FreeBSD. Now that FreeBSD supports
KSTAT_TYPE_RAW at least some of the functionality should
be made available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10842
In zvol_geom_open on first open we need to guarantee
that the namespace lock is held to avoid spurious
failures in zvol_first_open.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10841
A few kstats use KSTAT_TYPE_RAW to provide a string generated on
demand. Implementing these as sysctls was punted until now.
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10836
Commit dcdc12e added compatibility code to treat NR_SLAB_RECLAIMABLE_B
as if it were the same as NR_SLAB_RECLAIMABLE. However, the new value
is in bytes while the old value was in pages which means they are not
interchangeable.
The only place the reclaimable slab size is used is as a component of
the calculation done by arc_free_memory(). This function returns the
amount of memory the ARC considers to be free or reclaimable at little
cost. Rather than switch to a new interface to get this value it has
been removed it from the calculation. It is normally a minor component
compared to the number of inactive or free pages, and removing it
aligns the behavior with the FreeBSD version of arc_free_memory().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10834
The #pragma ident is a historical relic and not needed any more, this
pragma is actually unknown for common compilers and is only causing
trouble.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10810
The cache of struct svc_export and struct svc_expkey by nfsd and
rpc.mountd for the snapshot holds references to the mount point.
We need to flush them out before unmounting, otherwise umount
would fail with EBUSY.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#6000Closes#10783
In absence of inheriting entry for owner@, group@, or everyone@,
zfs_acl_chmod() is called to set these. This can cause confusion for Samba
admins who do not expect these entries to appear on newly created files and
directories once they have been stripped from from the parent directory.
When aclmode is set to "restricted", chmod is prevented on non-trivial ACLs.
It is not a stretch to assume that in this case the administrator does not want
ZFS to add the missing special entries. Add check for this aclmode, and if an
inherited entry is present skip zfs_acl_chmod().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#10748
Many modern devices use physical allocation units that are much
larger than the minimum logical allocation size accessible by
external commands. Two prevalent examples of this are 512e disk
drives (512b logical sector, 4K physical sector) and flash devices
(512b logical sector, 4K or larger allocation block size, and 128k
or larger erase block size). Operations that modify less than the
physical sector size result in a costly read-modify-write or garbage
collection sequence on these devices.
Simply exporting the true physical sector of the device to ZFS would
yield optimal performance, but has two serious drawbacks:
1. Existing pools created with devices that have different logical
and physical block sizes, but were configured to use the logical
block size (e.g. because the OS version used for pool construction
reported the logical block size instead of the physical block
size) will suddenly find that the vdev allocation size has
increased. This can be easily tolerated for active members of
the array, but ZFS would prevent replacement of a vdev with
another identical device because it now appears that the smaller
allocation size required by the pool is not supported by the new
device.
2. The device's physical block size may be too large to be supported
by ZFS. The optimal allocation size for the vdev may be quite
large. For example, a RAID controller may export a vdev that
requires read-modify-write cycles unless accessed using 64k
aligned/sized requests. ZFS currently has an 8k minimum block
size limit.
Reporting both the logical and physical allocation sizes for vdevs
solves these problems. A device may be used so long as the logical
block size is compatible with the configuration. By comparing the
logical and physical block sizes, new configurations can be optimized
and administrators can be notified of any existing pools that are
sub-optimal.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Macy <mmacy@freebsd.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10619
This option is used by FreeBSD boot loader.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#10738
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10727
We limit the size of nvlists passed to the kernel so a user cannot make
the kernel do an unreasonably large allocation. On FreeBSD this limit
was 128 kiB, which turns out to be a bit too small when doing some
operations involving a large number of datasets or snapshots, for
example replication.
Make this limit tunable, with a platform-specific auto default.
Linux keeps its limit at KMALLOC_MAX_SIZE. FreeBSD uses 1/4 of the
system limit on user wired memory, which allows it to scale depending
on system configuration.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Issue #6572Closes#10706
The ARC caches data in scatter ABD's, which are collections of pages,
which are typically 4K. Therefore, the space used to cache each block
is rounded up to a multiple of 4K. The ABD subsystem tracks this wasted
memory in the `scatter_chunk_waste` kstat. However, the ARC's `size` is
not aware of the memory used by this round-up, it only accounts for the
size that it requested from the ABD subsystem.
Therefore, the ARC is effectively using more memory than it is aware of,
due to the `scatter_chunk_waste`. This impacts observability, e.g.
`arcstat` will show that the ARC is using less memory than it
effectively is. It also impacts how the ARC responds to memory
pressure. As the amount of `scatter_chunk_waste` changes, it appears to
the ARC as memory pressure, so it needs to resize `arc_c`.
If the sector size (`1<<ashift`) is the same as the page size (or
larger), there won't be any waste. If the (compressed) block size is
relatively large compared to the page size, the amount of
`scatter_chunk_waste` will be small, so the problematic effects are
minimal.
However, if using 512B sectors (`ashift=9`), and the (compressed) block
size is small (e.g. `compression=on` with the default `volblocksize=8k`
or a decreased `recordsize`), the amount of `scatter_chunk_waste` can be
very large. On a production system, with `arc_size` at a constant 50%
of memory, `scatter_chunk_waste` has been been observed to be 10-30% of
memory.
This commit adds `scatter_chunk_waste` to `arc_size`, and adds a new
`waste` field to `arcstat`. As a result, the ARC's memory usage is more
observable, and `arc_c` does not need to be adjusted as frequently.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10701
`KMC_KMEM` and `KMC_VMEM` are now unused since all SPL-implemented
caches are `KMC_KVMEM`.
KMC_KMEM: Given the default value of `spl_kmem_cache_kmem_limit`, we
don't use kmalloc to back the SPL caches, instead we use kvmalloc
(KMC_KVMEM). The flag, module parameter, /proc entries, and associated
code are removed.
KMC_VMEM: This flag is not used, and kvmalloc() is always preferable to
vmalloc(). The flag, /proc entries, and associated code are removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10673
Stepping stone toward re-enabling spa_thread on FreeBSD.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10715
Linux and FreeBSD will most likely never see this issue.
On macOS when kext is unloaded, but zed is still connected, zed
will be issued ENODEV. As the cdevsw is released, the kernel
will not have zfsdev_release() called to release minor/onexit/events,
and it "leaks". This ensures it is cleaned up before unload.
Changed the for loop from zsprev, to zsnext style, for less
code duplication.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10700
The make_request_fn and associated API was replaced recently in a
Linux 5.9 merge, to replace its functionality with a new submit_bio
member in struct block_device_operations.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#10696
This was previously moved because nothing else in-tree uses it, but
evidently DilOS uses it out of tree.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#10361Closes#10685
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10682
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Remove dead code to make the implementation easier to understand.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Ahrens <matt@delphix.com>
Closes#10650
Must acquire the z_teardown_lock before accessing the zfsvfs_t object.
I can't reproduce this panic on demand, but this looks like the
correct solution.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: asomers <asomers@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10656
A collection of header changes to enable FreeBSD to build
with vendored OpenZFS.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10635
Change some comments copied from the Linux code to describe
the appropriate methods on FreeBSD.
Convert some tunables to ZFS_MODULE_PARAM so they get created
on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10647
The ARC shrinker callback `arc_shrinker_count/_scan()` is invoked by the
kernel's shrinker mechanism when the system is running low on free
pages. This happens via 2 code paths:
1. "direct reclaim": The system is attempting to allocate a page, but we
are low on memory. The ARC shrinker callback is invoked from the
page-allocation code path.
2. "indirect reclaim": kswapd notices that there aren't many free pages,
so it invokes the ARC shrinker callback.
In both cases, the kernel's shrinker code requests that the ARC shrinker
callback release some of its cache, and then it measures how many pages
were released. However, it's measurement of released pages does not
include pages that are freed via `__free_pages()`, which is how the ARC
releases memory (via `abd_free_chunks()`). Rather, the kernel shrinker
code is looking for pages to be placed on the lists of reclaimable pages
(which is separate from actually-free pages).
Because the kernel shrinker code doesn't detect that the ARC has
released pages, it may call the ARC shrinker callback many times,
resulting in the ARC "collapsing" down to `arc_c_min`. This has several
negative impacts:
1. ZFS doesn't use RAM to cache data effectively.
2. In the direct reclaim case, a single page allocation may wait a long
time (e.g. more than a minute) while we evict the entire ARC.
3. Even with the improvements made in 67c0f0dedc ("ARC shrinking blocks
reads/writes"), occasionally `arc_size` may stay above `arc_c` for the
entire time of the ARC collapse, thus blocking ZFS read/write operations
in `arc_get_data_impl()`.
To address these issues, this commit limits the ways that the ARC
shrinker callback can be used by the kernel shrinker code, and mitigates
the impact of arc_is_overflowing() on ZFS read/write operations.
With this commit:
1. We limit the amount of data that can be reclaimed from the ARC via
the "direct reclaim" shrinker. This limits the amount of time it takes
to allocate a single page.
2. We do not allow the ARC to shrink via kswapd (indirect reclaim).
Instead we rely on `arc_evict_zthr` to monitor free memory and reduce
the ARC target size to keep sufficient free memory in the system. Note
that we can't simply rely on limiting the amount that we reclaim at once
(as for the direct reclaim case), because kswapd's "boosted" logic can
invoke the callback an unlimited number of times (see
`balance_pgdat()`).
3. When `arc_is_overflowing()` and we want to allocate memory,
`arc_get_data_impl()` will wait only for a multiple of the requested
amount of data to be evicted, rather than waiting for the ARC to no
longer be overflowing. This allows ZFS reads/writes to make progress
even while the ARC is overflowing, while also ensuring that the eviction
thread makes progress towards reducing the total amount of memory used
by the ARC.
4. The amount of memory that the ARC always tries to keep free for the
rest of the system, `arc_sys_free` is increased.
5. Now that the shrinker callback is able to provide feedback to the
kernel's shrinker code about our progress, we can safely enable
the kswapd hook. This will allow the arc to receive notifications
when memory pressure is first detected by the kernel. We also
re-enable the appropriate kstats to track these callbacks.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10600
Renamed to avoid conflicting with refcount.h when a different
implementation is already provided by the platform.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10620
This is a step toward being able to vendor the OpenZFS code in FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10625
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10623
i386 has some additional memory reservation logic that limits the size
of the reported available memory. This was accidentally being used on
all arches due to a missing header.
Include machine/vmparam.h in freebsd/zfs/arc_os.c to pull in the
missing UMA_MD_SMALL_ALLOC definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10616
This is only used for the kstat, but something other than 0 is nice.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10626
By default, `spl_kmem_cache_expire` is `KMC_EXPIRE_MEM`, meaning that
objects will be removed from kmem cache magazines by
`spl_kmem_cache_reap_now()`.
There is also a module parameter to change this to `KMC_EXPIRE_AGE`,
which establishes a maximum lifetime for objects to stay in the
magazine. This setting has rarely, if ever, been used, and is not
regularly tested.
This commit removes the code for `KMC_EXPIRE_AGE`, and associated module
parameters.
Additionally, the unused module parameter
`spl_kmem_cache_obj_per_slab_min` is removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10608
Drop unnecessary redefinition's of several arcstat values.
Put missing extern declaration of arc_no_grow_shift in arc_impl.h.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10609
The process of evicting data from the ARC is referred to as
`arc_adjust`.
This commit changes the term to `arc_evict`, which is more specific.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10592
These tunables were renamed from vfs.zfs.arc_min and
vfs.zfs.arc_max to vfs.zfs.arc.min and vfs.zfs.arc.max.
Add legacy compat tunables for the old names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10579
The SPL kmem_cache implementation provides a mechanism, `skc_reclaim`,
whereby individual caches can register a callback to be invoked when
there is memory pressure. This mechanism is used in only one place: the
ARC registers the `hdr_recl()` reclaim function. This function wakes up
the `arc_reap_zthr`, whose job is to call `kmem_cache_reap()` and
`arc_reduce_target_size()`.
The `skc_reclaim` callbacks are invoked only by shrinker callbacks and
`arc_reap_zthr`, and only callback only wakes up `arc_reap_zthr`. When
called from `arc_reap_zthr`, waking `arc_reap_zthr` is a no-op. When
called from shrinker callbacks, we are already aware of memory pressure
and responding to it. Therefore there is little benefit to ever calling
the `hdr_recl()` `skc_reclaim` callback.
The `arc_reap_zthr` also wakes once a second, and if memory is low when
allocating an ARC buffer. Therefore, additionally waking it from the
shrinker calbacks has little benefit.
The shrinker callbacks can be invoked very frequently, e.g. 10,000 times
per second. Additionally, for invocation of the shrinker callback,
skc_reclaim is invoked many times. Therefore, this mechanism consumes
significant amounts of CPU time.
The kmem_cache shrinker calls `spl_kmem_cache_reap_now()`, which,
in addition to invoking `skc_reclaim()`, does two things to attempt to
free pages for use by the system:
1. Return free objects from the magazine layer to the slab layer
2. Return entirely-free slabs to the page layer (i.e. free pages)
These actions apply only to caches implemented by the SPL, not those
that use the underlying kernel SLAB/SLUB caches. The SPL caches are
used for objects >=32KB, which are primarily linear ABD's cached in the
DBUF cache.
These actions (freeing objects from the magazine layer and returning
entirely-free slabs) are also taken whenever a `kmem_cache_free()` call
finds a full magazine. So there would typically be zero entirely-free
slabs, and the number of objects in magazines is limited (typically no
more than 64 objects per magazine, and there's one magazine per CPU).
Therefore the benefit of `spl_kmem_cache_reap_now()`, while nonzero, is
modest.
We also call `spl_kmem_cache_reap_now()` from the `arc_reap_zthr`, when
memory pressure is detected. Therefore, calling
`spl_kmem_cache_reap_now()` from the kmem_cache shrinker is not needed.
This commit removes the `skc_reclaim` mechanism, its only callback
`hdr_recl()`, and the kmem_cache shrinker callback.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10576
Stock kernels older than 4.10 do not export the has_capability()
function which is required by commit e59a377. To avoid breaking
the build on older kernels revert to the safe legacy behavior and
return EACCES when privileges cannot be checked.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10565Closes#10573
`arc_free_memory()` returns the amount of memory that the ARC considers
to be free. This includes pages that are not actually free, but can be
evicted with essentially zero cost (without doing any i/o), for example
the page cache. The ARC can "squeeze out" any pages included in this
calculation, leaving only `arc_sys_free` (1/64th of RAM) for these
free/evictable pages.
Included in the count of free/evictable pages is
`nr_inactive_anon_pages()`, which is described as "Anonymous memory that
has not been used recently and can be swapped out". These pages would
have to be written out to disk (swap) in order to evict them, and they
are not included in `/proc/meminfo`'s `MemAvailable`.
Therefore it is not appropriate for `nr_inactive_anon_pages()` to be
included in the free/evictable memory returned by `arc_free_memory()`,
because the ARC shouldn't (intentionally) make the system swap.
This commit removes `nr_inactive_anon_pages()` from the memory returned
by `arc_free_memory()`. This is a step towards enabling the ARC to
manage free memory by monitoring it and reducing the ARC size as we
notice that there is insufficient free memory (in the `arc_reap_zthr`),
rather than the current method of relying on the `arc_shrinker`
callback.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10575
Update the zfs commands such that they're backwards compatible with
the version of ZFS is the base FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10542
Move/add include of <linux/percpu_compat.h> to satisfy missing
requirements.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain@dolbeau.org>
Closes#10568Closes#10569
On linux the list debug code has been setting off a failure when
checking that the node->next->prev value is pointing back at the node.
At times this check evaluates to 0xdead. When removing a child from a
gang ABD we must acquire the child's abd_mtx to make sure that the
same ABD is not being added to another gang ABD while it is being
removed from a gang ABD. This fixes a race condition when checking
if an ABDs link is already active and part of another gang ABD before
adding it to a gang.
Added additional debug code for the gang ABD in abd_verify() to make
sure each child ABD has active links. Also check to make sure another
gang ABD is not added to a gang ABD.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10511
The filesystem_limit and snapshot_limit properties limit the number of
filesystems or snapshots that can be created below this dataset.
According to the manpage, "The limit is not enforced if the user is
allowed to change the limit." Two types of users are allowed to change
the limit:
1. Those that have been delegated the `filesystem_limit` or
`snapshot_limit` permission, e.g. with
`zfs allow USER filesystem_limit DATASET`. This works properly.
2. A user with elevated system privileges (e.g. root). This does not
work - the root user will incorrectly get an error when trying to create
a snapshot/filesystem, if it exceeds the `_limit` property.
The problem is that `priv_policy_ns()` does not work if the `cred_t` is
not that of the current process. This happens when
`dsl_enforce_ds_ss_limits()` is called in syncing context (as part of a
sync task's check func) to determine the permissions of the
corresponding user process.
This commit fixes the issue by passing the `task_struct` (typedef'ed as
a `proc_t`) to syncing context, and then using `has_capability()` to
determine if that process is privileged. Note that we still need to
pass the `cred_t` to syncing context so that we can check if the user
was delegated this permission with `zfs allow`.
This problem only impacts Linux. Wrappers are added to FreeBSD but it
continues to use `priv_check_cred()`, which works on arbitrary `cred_t`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#8226Closes#10545
Previously a tqent could be recycled prematurely, update the
code to use a hash table for lookups to resolve this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10529
FreeBSD has a per-page "busy" lock which is held when handling a page
fault on a mapped file. This lock is also acquired when copying data
from the DMU to the page cache in zfs_write(). File range locks are
also acquired in both of these paths, in the opposite order with respect
to the busy lock.
In the getpages VOP, the range lock is only used to determine the extent
of optional read-ahead and read-behind operations. To resolve the lock
order reversal, modify the getpages VOP to avoid blocking on the range
lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10519
`zfs_freebsd_need_inactive` appears to been based on an unfinished
version of https://reviews.freebsd.org/D22130 which had a bug where
files written via mmap wouldn't actually persist.
Update the function to match the final version committed to FreeBSD.
Authored-by: Mateusz Guzik <mjg@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10527Closes#10528
Fix header conflicts when building zfs with openzfs as a vendor import.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10497
OS-specific code (e.g. under `module/os/linux`) does not need to share
its code structure with any other operating systems. In particular, the
ARC and kmem code need not be similar to the code in illumos, because we
won't be syncing this OS-specific code between operating systems. For
example, if/when illumos support is added to the common repo, we would
add a file `module/os/illumos/zfs/arc_os.c` for the illumos versions of
this code.
Therefore, we can simplify the code in the OS-specific ARC and kmem
routines.
These changes do not impact system behavior, they are purely code
cleanup. The changes are:
Arenas are not used on Linux or FreeBSD (they are always `NULL`), so
`heap_arena`, `zio_arena`, and `zio_alloc_arena` can be removed, along
with code that uses them.
In `arc_available_memory()`:
* `desfree` is unused, remove it
* rename `freemem` to avoid conflict with pre-existing `#define`
* remove checks related to arenas
* use units of bytes, rather than converting from bytes to pages and
then back to bytes
`SPL_KMEM_CACHE_REAP` is unused, remove it.
`skc_reap` is unused, remove it.
The `count` argument to `spl_kmem_cache_reap_now()` is unused, remove
it.
`vmem_size()` and associated type and macros are unused, remove them.
In `arc_memory_throttle()`, use a less confusing variable name to store
the result of `arc_free_memory()`.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10499
The SPL provides a wrapper for the kernel's shrinker callbacks, which
enables the ZFS code to interface with multiple versions of the shrinker
API's from different kernel versions. Specifically, Linux kernels 3.0 -
3.11 has a single "combined" callback, and Linux kernels 3.12 and later
have two "split" callbacks. The SPL provides a wrapper function so that
the ZFS code only needs to implement one version of the callbacks.
Currently the SPL's wrappers are designed such that the ZFS code
implements the older, "combined" callback. There are a few downsides to
this approach:
* The general design within ZFS is for the latest Linux kernel to be
considered the "first class" API.
* The newer, "split" callback API is easier to understand, because each
callback has one purpose.
* The current wrappers do not completely abstract out the differing
API's, so ZFS code needs `#ifdef` code to handle the differing return
values required for different kernel versions.
This commit addresses these drawbacks by having the ZFS code provide the
latest, "split" callbacks, and the SPL provides a wrapping function for
the older, "combined" API.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10502
A previous commit enabled the tracking of object allocations
in Linux-backed caches from the SPL layer for debuggability.
The commit is: 9a170fc6fe
Unfortunately, it also introduced minor performance regressions
that were highlighted by the ZFS perf test-suite. Within Delphix
we found that the regression would be from -1%, all the way up
to -8% for some workloads.
This commit brings performance back up to par by creating a
separate counter for those caches and making it a percpu in
order to avoid lock-contention.
The initial performance testing was done by myself, and the
final round was conducted by @tonynguien who was also the one
that discovered the regression and highlighted the culprit.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#10397
ZFS registers a memory hook, `__arc_shrinker_func`, which is supposed to
allow the ARC to shrink when the kernel experiences memory pressure.
The ARC shrinker changes `arc_c` via a call to
`arc_reduce_target_size()`. Before commit 3ec34e5527, the ARC
shrinker would also evict data from the ARC to bring `arc_size` down to
the new `arc_c`. However, that commit (seemingly inadvertently) made it
so that the ARC shrinker no longer evicts any data or waits for eviction
to complete.
Repeated calls to the ARC shrinker can reduce `arc_c` drastically, often
all the way to `arc_c_min`. Since it doesn't wait for the actual
eviction of data from the ARC, this creates a situation where `arc_size`
is more than `arc_c` for the several seconds/minutes it takes for
`arc_adjust_zthr` to evict data from the ARC. During this time,
arc_get_data_impl() will block, so ZFS can't process read/write requests
(e.g. from iSCSI, NFS, or read/write syscalls).
To ensure that `arc_c` doesn't shrink faster than the adjust thread can
keep up, this commit makes the ARC shrinker wait for the eviction to
complete, resulting in similar behavior to what we had before commit
3ec34e5527.
Note: commit 3ec34e5527 is `OpenZFS 9284 - arc_reclaim_thread
has 2 jobs` and was integrated in December 2018, and is part of ZoL
0.8.x but not 0.7.x.
Additionally, when the ARC size is reduced drastically, the
`arc_adjust_zthr` can be on-CPU for many seconds without blocking. Any
threads that are bound to the same CPU that arc_adjust_zthr is running
on will not able to run for a long time.
To ensure that CPU-bound threads can make progress, this commit changes
`arc_evict_state_impl()` make a voluntary preemption call,
`cond_resched()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-70703
Closes#10496
This tunable required a handler to be implemented for
ZFS_MODULE_PARAM_CALL.
Add the handler so the tunable can be declared in common code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10490
Rephrase comments to be more clear.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10481
Resolve the FreeBSD head build failure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10480
KPI changed in FreeBSD, update accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10475
spl-generic.c defines some of the libgcc integer library functions on
32-bit. Don't bother checking -Wmissing-prototypes since nothing should
directly call these functions from C code.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Include the header with prototypes in the file that provides definitions
as well, to catch any mismatch between prototype and definition.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Mark functions used only in the same translation unit as static. This
only includes functions that do not have a prototype in a header file
either.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10470
Implement semi-compatible functionality for mode=0 (preallocation)
and mode=FALLOC_FL_KEEP_SIZE (preallocation beyond EOF) for ZPL.
Since ZFS does COW and snapshots, preallocating blocks for a file
cannot guarantee that writes to the file will not run out of space.
Even if the first overwrite was guaranteed, it would not handle any
later overwrite of blocks due to COW, so strict compliance is futile.
Instead, make a best-effort check that at least enough free space is
currently available in the pool (with a bit of margin), then create
a sparse file of the requested size and continue on with life.
This does not handle all cases (e.g. several fallocate() calls before
writing into the files when the filesystem is nearly full), which
would require a more complex mechanism to be implemented, probably
based on a modified version of dmu_prealloc(), but is usable as-is.
A new module option zfs_fallocate_reserve_percent is used to control
the reserve margin for any single fallocate call. By default, this
is 110% of the requested preallocation size, so an additional 10% of
available space is reserved for overhead to allow the application a
good chance of finishing the write when the fallocate() succeeds.
If the heuristics of this basic fallocate implementation are not
desirable, the old non-functional behavior of returning EOPNOTSUPP
for calls can be restored by setting zfs_fallocate_reserve_percent=0.
The parameter of zfs_statvfs() is changed to take an inode instead
of a dentry, since no dentry is available in zfs_fallocate_common().
A few tests from @behlendorf cover basic fallocate functionality.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Arshad Hussain <arshad.super@gmail.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andreas Dilger <adilger@dilger.ca>
Issue #326Closes#10408
On Illumos callers of cv_timedwait and cv_timedwait_hires
can't distinguish between whether or not the cv was signaled
or the call timed out. Illumos handles this (for some definition
of handles) by calling cv_signal in the return path if we were
signaled but the return value indicates instead that we timed
out. This would make sense if it were possible to query the the
cv for its net signal disposition. However, this isn't possible
and, in spite of the fact that there are places in the code that
clearly take a different and incompatible path if a timeout value
is indicated, this distinction appears to be rather subtle to most
developers. This problem is further compounded by the fact that on
Linux, calling cv_signal in the return path wouldn't even do the
right thing unless there are other waiters.
Since it is possible for the caller to independently determine how
much time is remaining but it is not possible to query if the cv
was in fact signaled, prioritizing signalling over timeout seems
like a cleaner solution. In addition, judging from usage patterns
within the code itself, it is also less error prone.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10471
Apparently missed in the initial port integration was
the need to reap the abd_chunk_cache on FreeBSD. This
change addresses that oversight.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10474
Since https://reviews.freebsd.org/D24408 FreeBSD provides XDR functions
in the xdr module instead of krpc.
For FreeBSD 13, the MODULE_DEPEND should be changed to xdr
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10442Closes#10443
Linux defines different vdev_disk_t members to macOS, but they are
only used in vdev_disk.c so move the declaration there.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10452
In the event we are allocating a gang ABD in FreeBSD we are passing 0
to abd_alloc_struct(); however, this led to an allocation of ABD scatter
with 0 chunks. This left the gang ABD allocation 24 bytes smaller than
it should have been.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10431
For MIPS architectures on Linux the ZERO_PAGE macro references
empty_zero_page, which is exported as a GPL symbol. The call to
ZERO_PAGE in abd_alloc_zero_scatter has been removed and a single
zero'd page is now allocated for each of the pages in abd_zero_scatter
in the kernel ABD code path.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10428
The patch was applied to vdev_geom_open instead of vdev_geom_close by
mistake.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10427
The linux module can be built either as an external module, or compiled
into the kernel, using copy-builtin. The source and build directories
are slightly different between the two cases, and currently, compiling
into the kernel still refers to some files from the configured ZFS
source tree, instead of the copies inside the kernel source tree. There
is also duplication between copy-builtin, which creates a Kbuild file to
build ZFS inside the kernel tree, and the top-level module/Makefile.in.
Fix this by moving the list of modules and the CFLAGS settings into a
new module/Kbuild.in, which will be used by the kernel kbuild
infrastructure, and using KBUILD_EXTMOD to distinguish the two cases
within the Makefiles, in order to choose appropriate include
directories etc.
Module CFLAGS setting is simplified by using subdir-ccflags-y (available
since 2.6.30) to set them in the top-level Kbuild instead of each
individual module. The disabling of -Wunused-but-set-variable is removed
from the lua and zfs modules. The variable that the Makefile uses is
actually not defined, so this has no effect; and the warning has long
been disabled by the kernel Makefile itself.
The target_cpu definition in module/{zfs,zcommon} is removed as it was
replaced by use of CONFIG_SPARC64 in
commit 70835c5b75 ("Unify target_cpu handling")
os/linux/{spl,zfs} are removed from obj-m, as they are not modules in
themselves, but are included by the Makefile in the spl and zfs module
directories. The vestigial Makefiles in os and os/linux are removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10379Closes#10421
Correct various typos in the comments and tests.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#10423
Background:
By increasing the recordsize property above the default of 128KB, a
filesystem may have "large" blocks. By default, a send stream of such a
filesystem does not contain large WRITE records, instead it decreases
objects' block sizes to 128KB and splits the large blocks into 128KB
blocks, allowing the large-block filesystem to be received by a system
that does not support the `large_blocks` feature. A send stream
generated by `zfs send -L` (or `--large-block`) preserves the large
block size on the receiving system, by using large WRITE records.
When receiving an incremental send stream for a filesystem with large
blocks, if the send stream's -L flag was toggled, a bug is encountered
in which the file's contents are incorrectly zeroed out. The contents
of any blocks that were not modified by this send stream will be lost.
"Toggled" means that the previous send used `-L`, but this incremental
does not use `-L` (-L to no-L); or that the previous send did not use
`-L`, but this incremental does use `-L` (no-L to -L).
Changes:
This commit addresses the problem with several changes to the semantics
of zfs send/receive:
1. "-L to no-L" incrementals are rejected. If the previous send used
`-L`, but this incremental does not use `-L`, the `zfs receive` will
fail with this error message:
incremental send stream requires -L (--large-block), to match
previous receive.
2. "no-L to -L" incrementals are handled correctly, preserving the
smaller (128KB) block size of any already-received files that used large
blocks on the sending system but were split by `zfs send` without the
`-L` flag.
3. A new send stream format flag is added, `SWITCH_TO_LARGE_BLOCKS`.
This feature indicates that we can correctly handle "no-L to -L"
incrementals. This flag is currently not set on any send streams. In
the future, we intend for incremental send streams of snapshots that
have large blocks to use `-L` by default, and these streams will also
have the `SWITCH_TO_LARGE_BLOCKS` feature set. This ensures that streams
from the default use of `zfs send` won't encounter the bug mentioned
above, because they can't be received by software with the bug.
Implementation notes:
To facilitate accessing the ZPL's generation number,
`zfs_space_delta_cb()` has been renamed to `zpl_get_file_info()` and
restructured to fill in a struct with ZPL-specific info including owner
and generation.
In the "no-L to -L" case, if this is a compressed send stream (from
`zfs send -cL`), large WRITE records that are being written to small
(128KB) blocksize files need to be decompressed so that they can be
written split up into multiple blocks. The zio pipeline will recompress
each smaller block individually.
A new test case, `send-L_toggle`, is added, which tests the "no-L to -L"
case and verifies that we get an error for the "-L to no-L" case.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#6224Closes#10383
The l2arc_evict() function is responsible for evicting buffers which
reference the next bytes of the L2ARC device to be overwritten. Teach
this function to additionally TRIM that vdev space before it is
overwritten if the device has been filled with data. This is done by
vdev_trim_simple() which trims by issuing a new type of TRIM,
TRIM_TYPE_SIMPLE.
We also implement a "Trim Ahead" feature. It is a zfs module parameter,
expressed in % of the current write size. This trims ahead of the
current write size. A minimum of 64MB will be trimmed. The default is 0
which disables TRIM on L2ARC as it can put significant stress to
underlying storage devices. To enable TRIM on L2ARC we set
l2arc_trim_ahead > 0.
We also implement TRIM of the whole cache device upon addition to a
pool, pool creation or when the header of the device is invalid upon
importing a pool or onlining a cache device. This is dependent on
l2arc_trim_ahead > 0. TRIM of the whole device is done with
TRIM_TYPE_MANUAL so that its status can be monitored by zpool status -t.
We save the TRIM state for the whole device and the time of completion
on-disk in the header, and restore these upon L2ARC rebuild so that
zpool status -t can correctly report them. Whole device TRIM is done
asynchronously so that the user can export of the pool or remove the
cache device while it is trimming (ie if it is too slow).
We do not TRIM the whole device if persistent L2ARC has been disabled by
l2arc_rebuild_enabled = 0 because we may not want to lose all cached
buffers (eg we may want to import the pool with
l2arc_rebuild_enabled = 0 only once because of memory pressure). If
persistent L2ARC has been disabled by setting the module parameter
l2arc_rebuild_blocks_min_l2size to a value greater than the size of the
cache device then the whole device is trimmed upon creation or import of
a pool if l2arc_trim_ahead > 0.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam D. Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9713Closes#9789Closes#10224
Move the GFP flags kernel compat code from c file to kmem header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#10424
The `pgprot` argument has been removed from `__vmalloc` in Linux 5.8,
being `PAGE_KERNEL` always now [1].
Detect this during configure and define a wrapper for older kernels.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/mm/vmalloc.c?h=next-20200605&id=88dca4ca5a93d2c09e5bbc6a62fbfc3af83c4fca
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#10422
In Illumos it is possible to call ioctl functions from within the
kernel by passing the FKIOCTL flag. Neither FreeBSD nor Linux support
that, but it doesn't hurt to keep it around, as all the code is there.
Before this commit it was a dead code and zc_iflags was always zero.
Restore this functionality by allowing to pass a flag to the
zfsdev_ioctl_common() function.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#10417
By removing excessive includes it takes us a small step close to
compiling this file in userland.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#10415
The strcpy() and sprintf() functions are deprecated on some platforms.
Care is needed to ensure correct size is used. If some platforms
miss snprintf, we can add a #define to sprintf, likewise strlcpy().
The biggest change is adding a size parameter to zfs_id_to_fuidstr().
The various *_impl_get() functions are only used on linux and have
not yet been updated.
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#10400
C++ is a little picky about not using keywords for names, or string
constness.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10409
Expand the FreeBSD spl for kstats to support all current types
Move the dataset_kstats_t back to zvol_state_t from zfs_state_os_t
now that it is common once again
```
kstat.zfs/mypool.dataset.objset-0x10b.nunlinked: 0
kstat.zfs/mypool.dataset.objset-0x10b.nunlinks: 0
kstat.zfs/mypool.dataset.objset-0x10b.nread: 150528
kstat.zfs/mypool.dataset.objset-0x10b.reads: 48
kstat.zfs/mypool.dataset.objset-0x10b.nwritten: 134217728
kstat.zfs/mypool.dataset.objset-0x10b.writes: 1024
kstat.zfs/mypool.dataset.objset-0x10b.dataset_name: mypool/datasetname
```
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#10386
zvol_geom_bio_strategy should handle its own use of the zvol
suspend reader lock and ensure the zilog exists when needed.
A few other places using the zvol zilog should use the suspend
reader lock as well.
Simplify consumers of zvol_geom_bio_strategy, fix the locking, and
while in here, use the boolean_t constants with doread.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10381
Update API usage to reflect recent change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10384
Adding the gang ABD type, which allows for linear and scatter ABDs to
be chained together into a single ABD.
This can be used to avoid doing memory copies to/from ABDs. An example
of this can be found in vdev_queue.c in the vdev_queue_aggregate()
function.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian <bwa@clemson.edu>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10069
This is arguably a change for internal consistency within OpenZFS, as the
Linux implementation will reject read(2) on directories with EISDIR. It's
not unreasonable for read(2) to do something here on FreeBSD, but we don't
currently copy out anything useful anyways so start rejecting it with the
appropriate error.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#10338
We only use ZVOL_DIR on FreeBSD, and on FreeBSD it isn't correct.
Move the definition to the file where it is needed, and define it as
/dev/zvol/.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10337
The VN_OPEN_INVFS literal is in the wrong field.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: yparitcher <y@paritcher.com>
Closes#10322
Commit fc551d7 introduced the wrappers abd_enter_critical() and
abd_exit_critical() to mark critical sections. On Linux these are
implemented with the local_irq_save() and local_irq_restore() macros
which set the 'flags' argument when saving. By wrapping them with
a function the local variable is no longer set by the macro and is
no longer properly restored.
Convert abd_enter_critical() and abd_exit_critical() to macros to
resolve this issue and ensure the flags are properly restored.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10332
Reorganizing ABD code base so OS-independent ABD code has been placed
into a common abd.c file. OS-dependent ABD code has been left in each
OS's ABD source files, and these source files have been renamed to
abd_os.
The OS-independent ABD code is now under:
module/zfs/abd.c
With the OS-dependent code in:
module/os/linux/zfs/abd_os.c
module/os/freebsd/zfs/abd_os.c
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#10293
Modern bootloaders leverage data stored in the root filesystem to
enable some of their powerful features. GRUB specifically has a grubenv
file which can store large amounts of configuration data that can be
read and written at boot time and during normal operation. This allows
sysadmins to configure useful features like automated failover after
failed boot attempts. Unfortunately, due to the Copy-on-Write nature
of ZFS, the standard behavior of these tools cannot handle writing to
ZFS files safely at boot time. We need an alternative way to store
data that allows the bootloader to make changes to the data.
This work is very similar to work that was done on Illumos to enable
similar functionality in the FreeBSD bootloader. This patch is different
in that the data being stored is a raw grubenv file; this file can store
arbitrary variables and values, and the scripting provided by grub is
powerful enough that special structures are not required to implement
advanced behavior.
We repurpose the second padding area in each label to store the grubenv
file, protected by an embedded checksum. We add two ioctls to get and
set this data, and libzfs_core and libzfs functions to access them more
easily. There are no direct command line interfaces to these functions;
these will be added directly to the bootloader utilities.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10009
Sync up with the following changes from FreeBSD:
ZFS: add emulation of atomic_swap_64 and atomic_load_64
Some 32-bit platforms do not provide 64-bit atomic operations that ZFS
requires, either in userland or at all. We emulate those operations
for those platforms using a mutex. That is not entirely correct and
it's very efficient. Besides, the loads are plain loads, so torn
values are possible.
Nevertheless, the emulation seems to work for some definition of work.
This change adds atomic_swap_64, which is already used in ZFS code,
and atomic_load_64 that can be used to prevent torn reads.
Authored by: avg <avg@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@3458e5d1e6
cleanup of illumos compatibility atomics
atomic_cas_32 is implemented using atomic_fcmpset_32 on all platforms.
Ditto for atomic_cas_64 and atomic_fcmpset_64 on platforms that have
it. The only exception is sparc64 that provides MD atomic_cas_32 and
atomic_cas_64.
This is slightly inefficient as fcmpset reports whether the operation
updated the target and that information is not needed for cas.
Nevertheless, there is less code to maintain and to add for new
platforms. Also, the operations are done inline now as opposed to
function calls before.
atomic_add_64_nv is implemented using atomic_fetchadd_64 on platforms
that provide it.
casptr, cas32, atomic_or_8, atomic_or_8_nv are completely removed as
they have no users.
atomic_mtx that is used to emulate 64-bit atomics on platforms that
lack them is defined only on those platforms.
As a result, platform specific opensolaris_atomic.S files have lost
most of their code. The only exception is i386 where the
compat+contrib code provides 64-bit atomics for userland use. That
code assumes availability of cmpxchg8b instruction. FreeBSD does not
have that assumption for i386 userland and does not provide 64-bit
atomics. Hopefully, this can and will be fixed.
Authored by: avg <avg@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@e9642c209b
emulate illumos membar_producer with atomic_thread_fence_rel
membar_producer is supposed to be a store-store barrier.
Also, in the code that FreeBSD has ported from illumos membar_producer
is used only with regular stores to regular memory (with respect to
caching).
We do not have an MI primitive for the store-store barrier, so
atomic_thread_fence_rel is the closest we have as it provides
(load | store) -> store barrier.
Previously, membar_producer was an empty function call on all 32-bit
arm-s, 32-bit powerpc, riscv and all mips variants. I think that it
was inadequate.
On other platforms, such as amd64, arm64, i386, powerpc64, sparc64,
membar_producer was implemented using stronger primitives than required
for a store-store barrier with respect to regular memory access.
For example, it used sfence on amd64 and lock-ed nop in i386 (despite
TSO).
On powerpc64 we now use recommended lwsync instead of eieio.
On sparc64 FreeBSD uses TSO mode.
On arm64/aarch64 we now use dmb sy instead of dmb ish. Not sure if
this is an improvement, actually.
After this change we can drop opensolaris_atomic.S for aarch64, amd64,
powerpc64 and sparc64 as all required atomic operations have either
direct or light-weight mapping to FreeBSD native atomic operations.
Discussed with: kib
Authored by: avg <avg@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@50cdda62fc
fix up r353340, don't assume that fcmpset has strong semantics
fcmpset can have two kinds of semantics, weak and strong.
For practical purposes, strong semantics means that if fcmpset fails
then the reported current value is always different from the expected
value. Weak semantics means that the reported current value may be the
same as the expected value even though fcmpset failed. That's a so
called "sporadic" failure.
I originally implemented atomic_cas expecting strong semantics, but
many platforms actually have weak one.
Reported by: pkubaj (not confirmed if same issue)
Discussed with: kib, mjg
Authored by: avg <avg@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@238787c74e
[PowerPC] [MIPS] Implement 32-bit kernel emulation of atomic64 operations
This is a lock-based emulation of 64-bit atomics for kernel use, split off
from an earlier patch by jhibbits.
This is needed to unblock future improvements that reduce the need for
locking on 64-bit platforms by using atomic updates.
The implementation allows for future integration with userland atomic64,
but as that implies going through sysarch for every use, the current
status quo of userland doing its own locking may be for the best.
Submitted by: jhibbits (original patch), kevans (mips bits)
Reviewed by: jhibbits, jeff, kevans
Authored by: bdragon <bdragon@FreeBSD.org>
Differential Revision: https://reviews.freebsd.org/D22976
FreeBSD-commit: freebsd/freebsd@db39dab3a8
Remove sparc64 kernel support
Remove all sparc64 specific files
Remove all sparc64 ifdefs
Removee indireeect sparc64 ifdefs
Authored by: imp <imp@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@48b94864c5
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Ported-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10250
reflect delete permissions for ACLs
Authored by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
Porting Notes:
* Only comments are updated
OpenZFS-issue: https://www.illumos.org/issues/6765
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/da412744bcCloses#10266
- and some additional considerations
Authored by: Kevin Crowe <kevin.crowe@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/6762
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1eb4e906ecCloses#10266
with aclmode=passthrough
Authored by: Albert Lee <trisk@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/6764
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/de0f1ddb59Closes#10266
Authored-by: Paul B. Henson <henson@acm.org>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/3254
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/71dbfc287cCloses#10266
Porting notes:
* Updated zfs_acl_chmod to take 'boolean_t isdir' as first parameter
rather than 'zfsvfs_t *zfsvfs'
* zfs man pages changes mixed between zfs and new zfsprops man pages
Reviewed by: Aram Hvrneanu <aram@nexenta.com>
Reviewed by: Gordon Ross <gwr@nexenta.com>
Reviewed by: Robert Gordon <rbg@openrbg.com>
Reviewed by: Mark.Maybee@oracle.com
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@nexenta.com>
Ported-by: Paul B. Henson <henson@acm.org>
OpenZFS-issue: https://www.illumos.org/issues/742
OpenZFS-issue: https://www.illumos.org/issues/664
OpenZFS-issue: https://www.illumos.org/issues/279
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/a3c49ce110Closes#10266
zlib_inflateEnd was accidentally a wrapper for inflateInit instead of
inflateEnd, and hilarity ensues.
Fix the typo so we free memory instead of allocating more.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10225Closes#10252
Propagate changes in HEAD that mostly eliminate object locking.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10205
Remove some obsolete legacy compat, rename some misnamed, and add some
missing tunables for FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10203
Add the FreeBSD platform code to the OpenZFS repository. As of this
commit the source can be compiled and tested on FreeBSD 11 and 12.
Subsequent commits are now required to compile on FreeBSD and Linux.
Additionally, they must pass the ZFS Test Suite on FreeBSD which is
being run by the CI. As of this commit 1230 tests pass on FreeBSD
and there are no unexpected failures.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#898Closes#8987
We can improve the performance of writes to zvols by using
dmu_tx_hold_write_by_dnode() instead of dmu_tx_hold_write(). This
reduces lock contention on the first block of the dnode object, and also
reduces the amount of CPU needed. The benefit will be highest with
multi-threaded async writes (i.e. writes that don't call zil_commit()).
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10184
This commit makes the L2ARC persistent across reboots. We implement
a light-weight persistent L2ARC metadata structure that allows L2ARC
contents to be recovered after a reboot. This significantly eases the
impact a reboot has on read performance on systems with large caches.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Saso Kiselkov <skiselkov@gmail.com>
Co-authored-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Ported-by: Yuxuan Shui <yshuiv7@gmail.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#925Closes#1823Closes#2672Closes#3744Closes#9582
Set arc_c_min before arc_c_max so that when zfs_arc_min is set lower
than the default allmem/32 zfs_arc_max can also be set lower.
Add warning messages when tunables are being ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10157Closes#10158
Commit https://github.com/torvalds/linux/commit/3d745ea5 simplified
the blk_alloc_queue() interface by updating it to take the request
queue as an argument. Add a wrapper function which accepts the new
arguments and internally uses the available interfaces.
Other minor changes include increasing the Linux-Maximum to 5.6 now
that 5.6 has been released. It was not bumped to 5.7 because this
release has not yet been finalized and is still subject to change.
Added local 'struct zvol_state_os *zso' variable to zvol_alloc.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10181Closes#10187
Add a mechanism to wait for delete queue to drain.
When doing redacted send/recv, many workflows involve deleting files
that contain sensitive data. Because of the way zfs handles file
deletions, snapshots taken quickly after a rm operation can sometimes
still contain the file in question, especially if the file is very
large. This can result in issues for redacted send/recv users who
expect the deleted files to be redacted in the send streams, and not
appear in their clones.
This change duplicates much of the zpool wait related logic into a
zfs wait command, which can be used to wait until the internal
deleteq has been drained. Additional wait activities may be added
in the future.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Gallagher <john.gallagher@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#9707
In zfs_write(), the loop continues to the next iteration without
accounting for partial copies occurring in uiomove_iov when
copy_from_user/__copy_from_user_inatomic return a non-zero status.
This results in "zfs: accessing past end of object..." in the
kernel log, and the write failing.
Account for partial copies and update uio struct before returning
EFAULT, leave a comment explaining the reason why this is done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: ilbsmart <wgqimut@gmail.com>
Signed-off-by: Fabio Scaccabarozzi <fsvm88@gmail.com>
Closes#8673Closes#10148
== Summary ==
Prior to this change, sync writes to a zvol are processed serially.
This commit makes zvols process concurrently outstanding sync writes in
parallel, similar to how reads and async writes are already handled.
The result is that the throughput of sync writes is tripled.
== Background ==
When a write comes in for a zvol (e.g. over iscsi), it is processed by
calling `zvol_request()` to initiate the operation. ZFS is expected to
later call `BIO_END_IO()` when the operation completes (possibly from a
different thread). There are a limited number of threads that are
available to call `zvol_request()` - one one per iscsi client (unless
using MC/S). Therefore, to ensure good performance, the latency of
`zvol_request()` is important, so that many i/o operations to the zvol
can be processed concurrently. In other words, if the client has
multiple outstanding requests to the zvol, the zvol should have multiple
outstanding requests to the storage hardware (i.e. issue multiple
concurrent `zio_t`'s).
For reads, and async writes (i.e. writes which can be acknowledged
before the data reaches stable storage), `zvol_request()` achieves low
latency by dispatching the bulk of the work (including waiting for i/o
to disk) to a taskq. The taskq callback (`zvol_read()` or
`zvol_write()`) blocks while waiting for the i/o to disk to complete.
The `zvol_taskq` has 32 threads (by default), so we can have up to 32
concurrent i/os to disk in service of requests to zvols.
However, for sync writes (i.e. writes which must be persisted to stable
storage before they can be acknowledged, by calling `zil_commit()`),
`zvol_request()` does not use `zvol_taskq`. Instead it blocks while
waiting for the ZIL write to disk to complete. This has the effect of
serializing sync writes to each zvol. In other words, each zvol will
only process one sync write at a time, waiting for it to be written to
the ZIL before accepting the next request.
The same issue applies to FLUSH operations, for which `zvol_request()`
calls `zil_commit()` directly.
== Description of change ==
This commit changes `zvol_request()` to use
`taskq_dispatch_ent(zvol_taskq)` for sync writes, and FLUSh operations.
Therefore we can have up to 32 threads (the taskq threads)
simultaneously calling `zil_commit()`, for a theoretical performance
improvement of up to 32x.
To avoid the locking issue described in the comment (which this commit
removes), we acquire the rangelock from the taskq callback (e.g.
`zvol_write()`) rather than from `zvol_request()`. This applies to all
writes (sync and async), reads, and discard operations. This means that
multiple simultaneously-outstanding i/o's which access the same block
can complete in any order. This was previously thought to be incorrect,
but a review of the block device interface requirements revealed that
this is fine - the order is inherently not defined. The shorter hold
time of the rangelock should also have a slight performance improvement.
For an additional slight performance improvement, we use
`taskq_dispatch_ent()` instead of `taskq_dispatch()`, which avoids a
`kmem_alloc()` and eliminates a failure mode. This applies to all
writes (sync and async), reads, and discard operations.
== Performance results ==
We used a zvol as an iscsi target (server) for a Windows initiator
(client), with a single connection (the default - i.e. not MC/S).
We used `diskspd` to generate a workload with 4 threads, doing 1MB
writes to random offsets in the zvol. Without this change we get
231MB/s, and with the change we get 728MB/s, which is 3.15x the original
performance.
We ran a real-world workload, restoring a MSSQL database, and saw
throughput 2.5x the original.
We saw more modest performance wins (typically 1.5x-2x) when using MC/S
with 4 connections, and with different number of client threads (1, 8,
32).
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10163
Linux changed the default max ARC size to 1/2 of physical memory to
deal with shortcomings of the Linux SLUB allocator. Other platforms
do not require the same logic.
Implement an arc_default_max() function to determine a default max ARC
size in platform code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10155
If a has rollback has occurred while a file is open and unlinked.
Then when the file is closed post rollback it will not exist in the
rolled back version of the unlinked object. Therefore, the call to
zap_remove_int() may correctly return ENOENT and should be allowed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6812Closes#9739
The normal lock order is that the dp_config_rwlock must be held before
the ds_opening_lock. For example, dmu_objset_hold() does this.
However, dmu_objset_open_impl() is called with the ds_opening_lock held,
and if the dp_config_rwlock is not already held, it will attempt to
acquire it. This may lead to deadlock, since the lock order is
reversed.
Looking at all the callers of dmu_objset_open_impl() (which is
principally the callers of dmu_objset_from_ds()), almost all callers
already have the dp_config_rwlock. However, there are a few places in
the send and receive code paths that do not. For example:
dsl_crypto_populate_key_nvlist, send_cb, dmu_recv_stream,
receive_write_byref, redact_traverse_thread.
This commit resolves the problem by requiring all callers ot
dmu_objset_from_ds() to hold the dp_config_rwlock. In most cases, the
code has been restructured such that we call dmu_objset_from_ds()
earlier on in the send and receive processes, when we already have the
dp_config_rwlock, and save the objset_t until we need it in the middle
of the send or receive (similar to what we already do with the
dsl_dataset_t). Thus we do not need to acquire the dp_config_rwlock in
many new places.
I also cleaned up code in dmu_redact_snap() and send_traverse_thread().
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9662Closes#10115
__zio_execute() calls zio_taskq_member() to determine if we are running
in a zio interrupt taskq, in which case we may need to switch to
processing this zio in a zio issue taskq. The call to
zio_taskq_member() can become a performance bottleneck when we are
processing a high rate of zio's.
zio_taskq_member() calls taskq_member() on each of the zio interrupt
taskqs, of which there are 21. This is slow because each call to
taskq_member() does tsd_get(taskq_tsd), which on Linux is relatively
slow.
This commit improves the performance of zio_taskq_member() by having it
cache the value of tsd_get(taskq_tsd), reducing the number of those
calls to 1/21th of the current behavior.
In a test case running `zfs send -c >/dev/null` of a filesystem with
small blocks (average 2.5KB/block), zio_taskq_member() was using 6.7% of
one CPU, and with this change it is reduced to 1.3%. Overall time to
perform the `zfs send` reduced by 10% (~150,000 block/sec to ~165,000
blocks/sec).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10070
This function should only return "linux" on Linux.
Move the kernel part of the function out of common code.
Fix the tests for FreeBSD.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10079
By adding a zfs_file_private accessor to the common
interfaces and some extensions to FreeBSD platform
code it is now possible to share the implementations
for the aforementioned functions.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10073
Commit https://github.com/torvalds/linux/commit/9e8d42a0f accidentally
converted the static inline function blkg_tryget() to GPL-only for
kernels built with CONFIG_PREEMPT_RCU=y and CONFIG_BLK_CGROUP=y.
Resolve the build issue by providing our own equivalent functionality
when needed which uses rcu_read_lock_sched() internally as before.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#9745Closes#10072
As part of the Linux kernel's y2038 changes the time_t type has been
fully retired. Callers are now required to use the time64_t type.
Rather than move to the new type, I've removed the few remaining
places where a time_t is used in the kernel code. They've been
replaced with a uint64_t which is already how ZFS internally
handled these values.
Going forward we should work towards updating the remaining user
space time_t consumers to the 64-bit interfaces.
Reviewed-by: Matthew Macy <mmacy@freebsd.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10052Closes#10064
* Add dedicated donde_set_dirtyctx routine.
* Add empty dirty record on destroy assertion.
* Make much more extensive use of the SET_ERROR macro.
Reviewed-by: Will Andrews <wca@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#9924
The `convoff` function is called only in one code path in `zfs_space`.
Each caller of `zfs_space` is called with a `flock64_t` that has
`l_whence` set to `SEEK_SET`. This means that `convoff` always results
in a no-op as the `bfp` parameter has `l_whence` set to `SEEK_SET` and
`int whence` is `SEEK_SET` as well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Dirkjan Bussink <d.bussink@gmail.com>
Closes#10006
Unlinked files don't respect synchronous flush commands, but when they get relinked
their state is unknown. Previously we force flushed all such files even when
sync=disabled. Correct this case.
Reviewed-by: Chunwei Chen <tuxoko@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: DHE <git@dehacked.net>
Closes#10005
When growing the size of a (VMEM or KVMEM) kmem cache, spl_cache_grow()
always does taskq_dispatch(spl_cache_grow_work), and then waits for the
KMC_BIT_GROWING to be cleared by the taskq thread.
The taskq thread (spl_cache_grow_work()) does:
1. allocate new slab and add to list
2. wake_up_all(skc_waitq)
3. clear_bit(KMC_BIT_GROWING)
Therefore, the waiting thread can wake up before GROWING has been
cleared. It will see that the growing has not yet completed, and go
back to sleep until it hits the 100ms timeout.
This can have an extreme performance impact on workloads that alloc/free
more than fits in the (statically-sized) magazines. These workloads
allocate and free slabs with high frequency.
The problem can be observed with `funclatency spl_cache_grow`, which on
some workloads shows that 99.5% of the time it takes <64us to allocate
slabs, but we spend ~70% of our time in outliers, waiting for the 100ms
timeout.
The fix is to do `clear_bit(KMC_BIT_GROWING)` before
`wake_up_all(skc_waitq)`.
A future investigation should evaluate if we still actually need to
taskq_dispatch() at all, and if so on which kernel versions.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#9989
Jorgen Lundman
Attila Fülöp
Rich Ercolani
Alexander Motin
Paul Zuchowski
Alan Somers
jharmening
Brian Behlendorf
наб
Ryan Moeller
Coleman Kane
Alyssa Ross
Martin Matuška
Mateusz Guzik
Paul Dagnelie
Ryan Moeller
TerraTech
Matthew Ahrens
Andrea Gelmini
Luis Henriques
Brian Atkinson
Adam D. Moss
Don Brady
Mariusz Zaborski
Christian Schwarz
Andriy Gapon
Mark Johnston
Ryan Libby
khng300
Kleber Tarcísio
Matthew Macy
Konstantin Khorenko
Michael D Labriola
George Amanakis
Tony Perkins
Warner Losh
George Wilson
John Poduska
Spencer Kinny
Toomas Soome
youzhongyang
Andrew
Matthew Ahrens
Matthew Macy
Romain Dolbeau
Mark Johnston
Serapheim Dimitropoulos
Arvind Sankar
adilger
Michael Niewöhner
Pawel Jakub Dawidek
Allan Jude
Allan Jude
Brian Atkinson
Kyle Evans
yparitcher
Paul Dagnelie
Paul B. Henson
Fabio Scaccabarozzi
Dirkjan Bussink
DeHackEd