No installation diff, dist lost
-zfs-2.1.99/cmd/fsck_zfs/fsck.zfs
which was distributed erroneously, since it's generated
Also clean gitrev on clean
Also add -e 'any possible bashisms' to default checkbashisms flags,
and fully parallelise it and shellcheck, and it works out-of-tree, too
Also align the Release in the dist META file correctly
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13316
Deprecation of Python versions below 3.6 gives opportunity to unify the
build and install requirements for OpenZFS packages. The minimal
supported Python version is 3.6 as this is the most recent Python
package CentOS/RHEL 7 users can get.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12925
Replace "is" with "==" and "is not" with "!=".
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11394
With procfs_list kstats implemented for FreeBSD, dbufs are now exposed
as kstat.zfs.misc.dbufs.
On FreeBSD, dbufstats can use the sysctl instead of procfs when no
input file has been given.
Enable the dbufstats tests on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11008
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
A bunch of places need to edit files to incorporate the configured paths
i.e. bindir, sbindir etc. Move this logic into a common file.
Create arc_summary by copying arc_summary[23] as appropriate at build
time instead of install time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10559
The test added in commit
4313a5b4c5 ("Detect if sed supports --in-place")
doesn't work at least on my system (autoconfig-2.69).
The issue is that SED has already been found and cached before this
function is evaluated, with the result that the test is completely
skipped.
...
checking for a sed that does not truncate output... /usr/bin/sed
...
checking for sed --in-place... (cached) /usr/bin/sed
The first test is executed by libtool.m4. This looks to have been around
in libtool for at least 15 years or so, not sure why this was not
encountered at the time of the original commit.
Fix this by caching the value of the ac_inplace flag rather than the
path to SED. Also use $SED and add AC_REQUIRE to ensure that we use the
sed that was located by the standard configure test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Closes#10493
Not all versions of sed have the --in-place flag. Detect support for
the flag during ./configure and provide a fallback mechanism for those
systems where sed's behavior differs. The autoconf variable
${ac_inplace} can be used to choose the correct flags for editing a
file in place with sed.
Replace violating usages in Makefile.am with ${ac_inplace}.
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9463
/usr/bin/env python3 is the suggested[1] shebang for Python in general
(likewise for python2) and is conventional across platforms. This eases
development on systems where python is not installed in /usr/bin
(FreeBSD for example) and makes it possible to develop in virtual
environments (venv) for isolating dependencies.
Many packaging guidelines discourage the use of /usr/bin/env, but since
this is the canonical way of writing shebangs in the Python community,
many packaging scripts are already equipped to handle substituting the
appropriate absolute path to python automatically.
Some RPM package builders lacking brp-mangle-shebangs need a small
fallback mechanism in the package spec to stamp the appropriate shebang
on installed Python scripts.
[1]: https://docs.python.org/3/using/unix.html?#miscellaneous
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#9314
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9234
Almost all of the Python code in the respository has been updated
to be compatibile with Python 2.6, Python 3.4, or newer. The only
exceptions are arc_summery3.py which requires Python 3, and pyzfs
which requires at least Python 2.7. This allows us to maintain a
single version of the code and support most default versions of
python. This change does the following:
* Sets the default shebang for all Python scripts to python3. If
only Python 2 is available, then at install time scripts which
are compatible with Python 2 will have their shebangs replaced
with /usr/bin/python. This is done for compatibility until
Python 2 goes end of life. Since only the installed versions
are changed this means Python 3 must be installed on the system
for test-runner when testing in-tree.
* Added --with-python=<2|3|3.4,etc> configure option which sets
the PYTHON environment variable to target a specific python
version. By default the newest installed version of Python
will be used or the preferred distribution version when
creating pacakges.
* Fixed --enable-pyzfs configure checks so they are run when
--enable-pyzfs=check and --enable-pyzfs=yes.
* Enabled pyzfs for Python 3.4 and newer, which is now supported.
* Renamed pyzfs package to python<VERSION>-pyzfs and updated to
install in the appropriate site location. For example, when
building with --with-python=3.4 a python34-pyzfs will be
created which installs in /usr/lib/python3.4/site-packages/.
* Renamed the following python scripts according to the Fedora
guidance for packaging utilities in /bin
- dbufstat.py -> dbufstat
- arcstat.py -> arcstat
- arc_summary.py -> arc_summary
- arc_summary3.py -> arc_summary3
* Updated python-cffi package name. On CentOS 6, CentOS 7, and
Amazon Linux it's called python-cffi, not python2-cffi. For
Python3 it's called python3-cffi or python3x-cffi.
* Install one version of arc_summary. Depending on the version
of Python available install either arc_summary2 or arc_summary3
as arc_summary. The user output is only slightly different.
Reviewed-by: John Ramsden <johnramsden@riseup.net>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8096
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: George Melikov <mail@gmelikov.ru>
Signed-off-by: John Eismeier <john.eismeier@gmail.com>
Closes#7237
Introduce kstats about the dbuf hash and dbuf cache
to make it easier to inspect state. This should help
with debugging and understanding of these portions
of the codebase.
Correct format of dbuf kstat file.
Introduce a dbc column to dbufs kstat to indicate if
a dbuf is in the dbuf cache.
Introduce field filtering in the dbufstat python script.
Introduce a no header option to the dbufstat python script.
Introduce a test case to test basic mru->mfu list movement
in the ARC.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#6906
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#6535
arc_summary and dbufstat should have two spaces
after their last function definitions.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Closes#5881
Both scripts were returning an error code of 1
when using the -v argument. -v should exit with
an error code of 0.
Signed-off-by: Giuseppe Di Natale <dinatale2@llnl.gov>
To make arc_summary.py and dbufstat.py compatible with python3
some minor fixes were required, this was done automatically by
`2to3 -w arc_summary.py` and `2to3 -w dbufstat.py`.
Signed-off-by: Hajo Möller <dasjoe@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Reviewed-by: Richard Laager <rlaager@wiktel.com>
Commit ca0bf58d to address arcs_mtx contention removed column "index"
from the output of kstats/dbuf.
dbufstat.py was not updated to reflect this, which causes it to crash
when run with -bx
This removes "index" from hardcoded lists of columns.
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4096
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
Future proofing for compatibility with newer versions of Python.
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1838
Update the code to follow the pep8 style guide.
References:
http://www.python.org/dev/peps/pep-0008/
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1838
The dbufstat.py command was added to provide a conveniant way to
easily determine what ZFS is caching. The script consumes the
raw /proc/spl/kstat/zfs/dbufs kstat data can consolidates it in
to a more human readable form. This was designed primarily as
a tool to aid developers but it may also be useful for advanced
users who want more visibility in to what the ARC is caching.
When run without options dbufstat.py will default to showing a
list of all objects with at least one buffer present in the
cache. The total cache space consumed by that object will be
printed on the right along with the object type. Similar to the
arcstats.py command the -x option may used to display additional
fields.
Two other modes of operation are also supported by dbufstat.py
and the expectation is additional display modes may be added as
needed. The -t option will summerize the total number of bytes
cached for each object type, and the -b option will show every
dbuf currently cached.
The script was designed to be consistent with arcstat.py and
includes most of the same options and funcationality.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
наб
Damian Szuberski
Ryan Moeller
Michael Niewöhner
Arvind Sankar
Ryan Moeller
Andrea Gelmini
Brian Behlendorf
John Eismeier
Giuseppe Di Natale
LOLi
Giuseppe Di Natale
Hajo Möller
Olaf Faaland
Turbo Fredriksson
Matthew Thode