ZoL commit 1421c89 unintentionally changed the disk format in a forward-
compatible, but not backward compatible way. This was accomplished by
adding an entry to zbookmark_t, which is included in a couple of
on-disk structures. That lead to the creation of pools with incorrect
dsl_scan_phys_t objects that could only be imported by versions of ZoL
containing that commit. Such pools cannot be imported by other versions
of ZFS or past versions of ZoL.
The additional field has been removed by the previous commit. However,
affected pools must be imported and scrubbed using a version of ZoL with
this commit applied. This will return the pools to a state in which they
may be imported by other implementations.
The 'zpool import' or 'zpool status' command can be used to determine if
a pool is impacted. A message similar to one of the following means your
pool must be scrubbed to restore compatibility.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #1 detected.
action: The pool can be imported using its name or numeric identifier,
however there is a compatibility issue which should be corrected
by running 'zpool scrub'
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
$ zpool status
pool: zol-0.6.2-173
state: ONLINE
scan: pool compatibility issue detected.
see: https://github.com/zfsonlinux/zfs/issues/2094
action: To correct the issue run 'zpool scrub'.
config:
...
If there was an async destroy in progress 'zpool import' will prevent
the pool from being imported. Further advice on how to proceed will be
provided by the error message as follows.
$ zpool import
pool: zol-0.6.2-173
id: 1165955789558693437
state: ONLINE
status: Errata #2 detected.
action: The pool can not be imported with this version of ZFS due to an
active asynchronous destroy. Revert to an earlier version and
allow the destroy to complete before updating.
see: http://zfsonlinux.org/msg/ZFS-8000-ER
config:
...
Pools affected by the damaged dsl_scan_phys_t can be detected prior to
an upgrade by running the following command as root:
zdb -dddd poolname 1 | grep -P '^\t\tscan = ' | sed -e 's;scan = ;;' | wc -w
Note that `poolname` must be replaced with the name of the pool you wish
to check. A value of 25 indicates the dsl_scan_phys_t has been damaged.
A value of 24 indicates that the dsl_scan_phys_t is normal. A value of 0
indicates that there has never been a scrub run on the pool.
The regression caused by the change to zbookmark_t never made it into a
tagged release, Gentoo backports, Ubuntu, Debian, Fedora, or EPEL
stable respositorys. Only those using the HEAD version directly from
Github after the 0.6.2 but before the 0.6.3 tag are affected.
This patch does have one limitation that should be mentioned. It will not
detect errata #2 on a pool unless errata #1 is also present. It expected
this will not be a significant problem because pools impacted by errata #2
have a high probably of being impacted by errata #1.
End users can ensure they do no hit this unlikely case by waiting for all
asynchronous destroy operations to complete before updating ZoL. The
presence of any background destroys on any imported pools can be checked
by running `zpool get freeing` as root. This will display a non-zero
value for any pool with an active asynchronous destroy.
Lastly, it is expected that no user data has been lost as a result of
this erratum.
Original-patch-by: Tim Chase <tim@chase2k.com>
Reworked-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2094
From time to time it may be necessary to inform the pool administrator
about an errata which impacts their pool. These errata will by shown
to the administrator through the 'zpool status' and 'zpool import'
output as appropriate. The errata must clearly describe the issue
detected, how the pool is impacted, and what action should be taken
to resolve the situation. Additional information for each errata will
be provided at http://zfsonlinux.org/msg/ZFS-8000-ER.
To accomplish the above this patch adds the required infrastructure to
allow the kernel modules to notify the utilities that an errata has
been detected. This is done through the ZPOOL_CONFIG_ERRATA uint64_t
which has been added to the pool configuration nvlist.
To add a new errata the following changes must be made:
* A new errata identifier must be assigned by adding a new enum value
to the zpool_errata_t type. New enums must be added to the end to
preserve the existing ordering.
* Code must be added to detect the issue. This does not strictly
need to be done at pool import time but doing so will make the
errata visible in 'zpool import' as well as 'zpool status'. Once
detected the spa->spa_errata member should be set to the new enum.
* If possible code should be added to clear the spa->spa_errata member
once the errata has been resolved.
* The show_import() and status_callback() functions must be updated
to include an informational message describing the errata. This
should include an action message describing what an administrator
should do to address the errata.
* The documentation at http://zfsonlinux.org/msg/ZFS-8000-ER must be
updated to describe the errata. This space can be used to provide
as much additional information as needed to fully describe the errata.
A link to this documentation will be automatically generated in the
output of 'zpool import' and 'zpool status'.
Original-idea-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
Both the zpool_import_status() and zpool_get_status() functions
return the zpool_status_t enum. This explicit type should be used
rather than the more generic int type.
This patch makes no functional change and should only be considered
code cleanup. It happens to have been done in the context of #2094
because that's when I noticed this issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Richard Yao <ryao@gentoo.or
Issue #2094
The chunksize must always be strictly smaller than the regionsize.
Signed-off-by: Andrew Uselton <andrew.c.uselton@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2072
The vdev_id udev helper currently applies slot renumbering rules to
every channel (JBOD) in the system. This is too inflexible for systems
with non-homogeneous storage topologies. The "slot" keyword now takes
an optional third parameter which names a channel to which the mapping
will apply. If the third parameter is omitted then the rule applies to
all channels. The first-specified rule that can match a slot takes
precedence. Therefore a channel-specific rule for a given slot should
generally appear before a generic rule for the same slot number. In
this way a custom slot mapping can be applied to a particular channel
and a default mapping applied to the rest.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2056
31fc19399e incorrectly removed $(LIBBLKID)
from cmd/zpool/Makefile.am. This meant that the toolchain was not given
-lblkid, which resulted in the following build failure on Ubuntu 13.10:
/usr/bin/ld: zpool_vdev.o: undefined reference to symbol
'blkid_put_cache@@BLKID_1.0'
/lib/x86_64-linux-gnu/libblkid.so.1: error adding symbols: DSO missing
from command line
collect2: error: ld returned 1 exit status
That commit reworked various Makefile.am to follow best practices, so we
reintroduce $(LIBBLKID) in a manner consistent with that, rather than
explicitly reverting the change.
Reproduction of this issue was done on a Gentoo Linux system by
executing the following commands:
zfs create -o mountpoint=/mnt/ubuntu-13.10 rpool/ROOT/ubuntu-13.10
debootstrap --variant=buildd --arch amd64 saucy /mnt/ubuntu-13.10 http://archive.ubuntu.com/ubuntu/
mount -o bind /dev /mnt/ubuntu-13.10/dev/
mount -o bind /proc/ /mnt/ubuntu-13.10/proc/
mount -o bind /sys/ /mnt/ubuntu-13.10/sys/
cp /etc/resolv.conf /mnt/ubuntu-13.10/etc/
(cd /mnt/ubuntu-13.10/root/ && git clone git://github.com/zfsonlinux/zfs.git)
chroot /mnt/ubuntu-13.10/
apt-get install git autoconf libtool zlib1g-dev uuid-dev libblkid-dev
\#apt-get install alien fakeroot vim
cd /root/zfs
./autogen.sh
./configure --with-config=user --prefix=/usr
make
That will create a Ubuntu 13.10 chroot, fetch the sources and build
test. At this point, cmd/zpool/Makefile.am was modified and the
following commands were run to verify that the build issue was resolved:
git clean -xdf
./autogen.sh
./configure --with-config=user --prefix=/usr
make
Although it is not shown here, the absence of libblkid-dev enables ZFS
to build successfully without the patch. This could explain how this
escaped detection until recently. A test without libblkid-dev was done
to verify that the patch did not cause a regression in the absence of
libblkid:
apt-get remove libblkid-dev
git clean -xdf
./autogen.sh
./configure --with-config=user --prefix=/usr
make
Additionally, the commands themselves were tested against my live system
from within the chroot to ensure basic functionality. My live system had
corresponding kernel modules already installed and basic commands such
as `zpool list` and `zfs list` worked without incident. Lastly, this
patch was also build tested on Gentoo Linux, where it caused no
problems.
At time of writing, these steps can be used to reproduce these results
on any modern Linux system that has debootstrap installed. On Gentoo,
installing debootstrap can be done with `emerge dev-util/debootstrap`.
The current ZFSOnLinux HEAD revision as of writing is
fd23720ae1. Once this is fixed in HEAD,
either that revision or another before this fix and after
31fc19399e will be needed to reproduce
this issue.
Lastly, it remains to be seen why the toolchains on the systems
performing regression tests did not catch this. This is not a
ZFS-specific issue, but it is something that we will want to explore in
the future.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2038
Re-enable the /etc/mtab cache to prevent the zfs command from
having to repeatedly open and read from the /etc/mtab file.
Instead an AVL tree of the mounted filesystems is created and
used to vastly speed up lookups. This means that if non-zfs
filesystems are mounted concurrently the 'zfs mount' will not
immediately detect them. In practice that will rarely happen
and even if it does the absolute worst case would be a failed
mount. This was originally disabled out of an abundance of
paranoia.
NOTE: There may still be some parts of the code which do not
consult the mtab cache. They should be updated to check the
mtab cache as they as discovered to be a problem.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #845
Move the libzfs_fini() after the zpool_log_history() call so the
ZPOOL_HIST_CMD entry can get written.
Fix the handling of saved_poolname in zfsdev_ioctl()
which was broken as part of the stack-reduction work in
a168788053.
Since ZoL destroys the TSD data in which the previously successful
ioctl()'s pool name is stored following every vop, the ZFS_IOC_LOG_HISTORY
ioctl has a very important restriction: it can only successfully write
a long entry following a successful ioctl() if no intervening vops have
been performed. Some of zfs subcommands do perform intervening vops and
to do the logging themselves. At the moment, the "create" and "clone"
subcommands have been modified appropriately.
Signed-off-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1998
Four new dataset properties have been added to support SELinux. They
are 'context', 'fscontext', 'defcontext' and 'rootcontext' which map
directly to the context options described in mount(8). When one of
these properties is set to something other than 'none'. That string
will be passed verbatim as a mount option for the given context when
the filesystem is mounted.
For example, if you wanted the rootcontext for a filesystem to be set
to 'system_u:object_r:fs_t' you would set the property as follows:
$ zfs set rootcontext="system_u:object_r:fs_t" storage-pool/media
This will ensure the filesystem is automatically mounted with that
rootcontext. It is equivalent to manually specifying the rootcontext
with the -o option like this:
$ zfs mount -o rootcontext=system_u:object_r:fs_t storage-pool/media
By default all four contexts are set to 'none'. Further information
on SELinux contexts is detailed in mount(8) and selinux(8) man pages.
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#1504
The vast majority of these changes are in Linux specific code.
They are the result of not having an automated style checker to
validate the code when it was originally written. Others were
caused when the common code was slightly adjusted for Linux.
This patch contains no functional changes. It only refreshes
the code to conform to style guide.
Everyone submitting patches for inclusion upstream should now
run 'make checkstyle' and resolve any warning prior to opening
a pull request. The automated builders have been updated to
fail a build if when 'make checkstyle' detects an issue.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1821
4208 Typo in zfs_main.c: "posxiuser"
Reviewed by: Sonu Pillai <sonu.pillai@delphix.com>
Reviewed by: Will Guyette <will.guyette@delphix.com>
Reviewed by: Eric Diven <eric.diven@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/4208illumos/illumos-gate@f38cb554a5
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1986
Add acl, noacl and posixacl to option_map, avoiding ENOENT error
case when mount from util-linux-2.24 execs mount.zfs with any of
those flags
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: renelson <bnelson@nelsonbe.com>
Issue #1968
A minor grammar error was corrected in in the parse_options()
error handling for the ENOENT case.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: renelson <bnelson@nelsonbe.com>
Issue #1968
The bug is caused by multipath output like this:
35000c50056bd77a7 dm-15 HP,MB3000FCWDH
size=2.7T features='0' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=0 status=active
| `- 2:0:16:0 sdq 65:0 active undef running
`-+- policy='round-robin 0' prio=0 status=enabled
`- 4:0:52:0 sdfp 130:176 active undef running
Note that the pipe symbols mean that the field numbering is different
between the sdq and sdfp lines. The fix edits out the pipe symbols.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1692
Added:
Adata S396 (obtained from drive_id)
Apple MacBookAir3,1 SSD (obtained from drive_id)
Apple MacBookPro10,1 SSD (obtained from drive_id)
Intel 510 (obtained from drive_id)
Intel 710 (obtained from drive_id)
Intel DC S3500 (obtained from drive_id)
Netapp LUN (obtained from illumos user's sd.conf)
OCZ Agility 3 (obtained from drive_id)
OCZ Vertex (obtained from drive_id)
Samsung PM800 (obtained from drive_id)
Sandisk U100 (obtained from drive_id)
Sun Comstar (obtained from illumos user's sd.conf)
Notes:
1. The entries for the Intel DC S3500 were extrapolated from the 800GB
model's entry, which is "ATA INTEL SSDSC2BB80".
2. The entires for the Intel 710 were extrapolated from the 120GG
model's entry, which is "ATA INTEL SSDSA2BZ12".
3. The entires for the Intel 510 were extrapolated from the 250GB
model's entry, which is "ATA INTEL SSDSC2MH25".
4. The entires for the Apple MacBookPro10,1 SSD were extrapolated from
the 512GB model's entry, which is "ATA APPLE SSD SM512E". Google
searches suggest that this is a rebadged Samsung 830.
5. The entires for the Apple MacBookAir3,1 SSD were extrapolated from
the 128GB model's entry, which is "ATA APPLE SSD TS128C". Google
searches suggest that this is a rebadged Kingston SSDNow V+ 100 (based
on Toshiba).
6. Sun Comstar is an iSCSI Target, so we cannot tell what the correct
sector size is through this method. We list it only for reference
purposes, but it is commented out. Similarly, it is not clear what the
right thing to do for Netapp is, so we comment it out.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1907
On some platforms symbols provided by libzfs_core and used by
libzfs were not available to the linker. To avoid this issue
libzfs_core has been added to the list of required libraries
when building utilities which depend on libzfs. This should
have been handled properly by libtool and it's still not
entirely clear why it wasn't on all platforms.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1841
Future proofing for compatibility with newer versions of Python.
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1838
Update the code to follow the pep8 style guide.
References:
http://www.python.org/dev/peps/pep-0008/
Signed-off-by: Matthew Thode <prometheanfire@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1838
In the current snapshot automount implementation, it is possible for
multiple mounts to attempted concurrently. Only one of the mounts will
succeed and the other will fail. The failed mounts will cause an EREMOTE
to be propagated back to the application.
This commit works around the problem by adding a new exit status,
MOUNT_BUSY to the mount.zfs program which is used when the underlying
mount(2) call returns EBUSY. The zfs code detects this condition and
treats it as if the mount had succeeded.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1819
3956 ::vdev -r should work with pipelines
3957 ztest should update the cachefile before killing itself
3958 multiple scans can lead to partial resilvering
3959 ddt entries are not always resilvered
3960 dsl_scan can skip over dedup-ed blocks if physical birth != logical birth
3961 freed gang blocks are not resilvered and can cause pool to suspend
3962 ztest should print out zfs debug buffer before exiting
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/3956https://www.illumos.org/issues/3957https://www.illumos.org/issues/3958https://www.illumos.org/issues/3959https://www.illumos.org/issues/3960https://www.illumos.org/issues/3961https://www.illumos.org/issues/3962illumos/illumos-gate@b4952e17e8
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Porting notes:
1. zfs_dbgmsg_print() is only used in userland. Since we do not have
mdb on Linux, it does not make sense to make it available in the
kernel. This means that a build failure will occur if any future
kernel patch depends on it. However, that is unlikely given that
this functionality was added to support zdb.
2. zfs_dbgmsg_print() is only invoked for -VVV or greater log levels.
This preserves the existing behavior of minimal noise when running
with -V, and -VV.
3. In vdev_config_generate() the call to nvlist_alloc() was not
changed to fnvlist_alloc() because we must pass KM_PUSHPAGE in
the txg_sync context.
3949 ztest fault injection should avoid resilvering devices
3950 ztest: deadman fires when we're doing a scan
3951 ztest hang when running dedup test
3952 ztest: ztest_reguid test and ztest_fault_inject don't place nice together
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/3949https://www.illumos.org/issues/3950https://www.illumos.org/issues/3951https://www.illumos.org/issues/3952illumos/illumos-gate@2c1e2b4414
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Porting notes:
1. The deadman thread was removed from ztest during the original
port because it depended on Solaris thr_create() interface.
This functionality should be reintroduced using the more
portable pthreads.
3112 ztest does not honor ZFS_DEBUG
3113 ztest should use watchpoints to protect frozen arc bufs
3114 some leaked nvlists in zfsdev_ioctl
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Amdur <Matt.Amdur@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Eric Schrock <eric.schrock@delphix.com>
References:
https://www.illumos.org/issues/3112https://www.illumos.org/issues/3113https://www.illumos.org/issues/3114illumos/illumos-gate@cd1c8b85eb
The /proc/self/cmd watchpoint interface is specific to Solaris.
Therefore, the #3113 implementation was reworked to use the more
portable mprotect(2) system call. When the pages are watched they
are marked read-only for protection. Any write to the protected
address range immediately trigger a SIGSEGV. The pages are marked
writable again when they are unwatched.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1489
3236 zio nop-write
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
References:
illumos/illumos-gate@80901aea8ehttps://www.illumos.org/issues/3236
Porting Notes
1. This patch is being merged dispite an increased instance of
https://www.illumos.org/issues/3113 being triggered by ztest.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1489
3894 zfs should not allow snapshot of inconsistent dataset
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Gordon Ross <gwr@nexenta.com>
References:
https://www.illumos.org/issues/3894illumos/illumos-gate@ca48f36f20
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3740 Poor ZFS send / receive performance due to snapshot
hold / release processing
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3740illumos/illumos-gate@a7a845e4bf
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Porting notes:
1. 13fe019870 introduced a merge conflict
in dsl_dataset_user_release_tmp where some variables were moved
outside of the preprocessor directive.
2. dea9dfefdd747534b3846845629d2200f0616dad made the previous merge
conflict worse by switching KM_SLEEP to KM_PUSHPAGE. This is notable
because this commit refactors the code, adding a new KM_SLEEP
allocation. It is not clear to me whether this should be converted
to KM_PUSHPAGE.
3. We had a merge conflict in libzfs_sendrecv.c because of copyright
notices.
4. Several small C99 compatibility fixed were made.
3745 zpool create should treat -O mountpoint and -m the same
3811 zpool create -o altroot=/xyz -O mountpoint=/mnt ignores
the mountpoint option
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Christopher Siden <christopher.siden@delphix.com>
References:
https://www.illumos.org/issues/3745https://www.illumos.org/issues/3811illumos/illumos-gate@8b71377531
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
3603 panic from bpobj_enqueue_subobj()
3604 zdb should print bpobjs more verbosely
3871 GCC 4.5.3 does not like issue 3604 patch
Reviewed by: Henrik Mattson <henrik.mattson@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Dan McDonald <danmcd@nexenta.com>
References:
https://www.illumos.org/issues/3603https://www.illumos.org/issues/3604https://www.illumos.org/issues/3871illumos/illumos-gate@d04756377d
Ported-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1775
Note that the patch from Illumos issue 3871 is not accepted into Illumos
at the time of this writing. It is something that I wrote when porting
this. Documentation is in the Illumos issue.
This works the same as the -p switch to "zfs get", displaying full
resolution values for appropriate attributes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1813
The dbufstat.py command was added to provide a conveniant way to
easily determine what ZFS is caching. The script consumes the
raw /proc/spl/kstat/zfs/dbufs kstat data can consolidates it in
to a more human readable form. This was designed primarily as
a tool to aid developers but it may also be useful for advanced
users who want more visibility in to what the ARC is caching.
When run without options dbufstat.py will default to showing a
list of all objects with at least one buffer present in the
cache. The total cache space consumed by that object will be
printed on the right along with the object type. Similar to the
arcstats.py command the -x option may used to display additional
fields.
Two other modes of operation are also supported by dbufstat.py
and the expectation is additional display modes may be added as
needed. The -t option will summerize the total number of bytes
cached for each object type, and the -b option will show every
dbuf currently cached.
The script was designed to be consistent with arcstat.py and
includes most of the same options and funcationality.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When creating a new pool, or adding/replacing a disk in an existing
pool, partition tables will be automatically created on the devices.
Under normal circumstances it will take less than a second for udev
to create the expected device files under /dev/. However, it has
been observed that if the system is doing heavy IO concurrently udev
may take far longer. If you also throw in some cheap dodgy hardware
it may take even longer.
To prevent zpool commands from failing due to this the default wait
time for udev is being increased to 30 seconds. This will have no
impact on normal usage, the increase timeout should only be noticed
if your udev rules are incorrectly configured.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1646
Document the "-D" and "-T" options and the optional interval
and count or "zpool status".
Also for zpool's man page, use a consistent order for the
various "-T" options to match the program's help output.
Document the effect of additional "-D" options for zdb.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1786
Libraries that depend on other libraries should list them in ELF's
DT_NEEDED field so that programs linking to them do not need to specify
those libraries unless they depend on them as well. This is not the case
in the current code and the consequence is that anything that needs a
library must know its dependencies. This is fragile and caused GRUB2's
configure script to break when a dependency was added on libblkid in
libzfs.
This resolves that problem by using LIBADD/LDADD to specify libraries in
Makefile.am instead of LDFLAGS. This ensures that proper DT_NEEDED
entries are generated and prevents GRUB2's configure script from
breaking in the presence of a libblkid dependency. This also removes
unneeded dependencies from various files.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1751
Add Corsair Force GS drive (obtained from drive_id)
Add Kingston HyperX 3K (obtained from drive_id)
Add OCZ Vertex 4 drive (obtained from drive_id)
Add Samsung SM843T enterprise drive (obtained from drive_id)
Add entries for additional sizes of Intel 320/330/335/520 series
Add Cruical C400 (obtained from Illumos user's sd.conf)
Add Toshiba SSD (obtained from Illumos user's sd.conf)
Add Samsung's first SLC SSD (obtained from drive_id)
Add OCZ Core Series (obtained from drive_id)
Add Intel DC S3700 (obtained from drive_id)
Notes:
1. The drive identifer obtained for the Samsung SM843T was MZ7WD480. The
rest were extrapolated. The additional entries were checked with Google
to verify that such drives exist in the wild.
2. The additional entries for Intel drives were extrapolated from
existing entries. The additional entries were checked with Google to
verify that such drives exist in the wild.
3. The "ATA C400-MTFDDAC512M" and "ATA TOSHIBA THNSNH51" entries
are from the sd.conf of gcbirzan on freenode. Additional entries were
extrapolated from them and checked with Google.
4. I obtained the Samsung MCCOE64G entry from an actual drive. The
Samsung MCCOE32G entry was extrapolated from it and checked with
Google.
5. I obtained the SSDSC2BA10 from a 100GB Intel DC S3700 drive and
extrapolated the entries for the additional models.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1752
2882 implement libzfs_core
2883 changing "canmount" property to "on" should not always remount dataset
2900 "zfs snapshot" should be able to create multiple, arbitrary snapshots at once
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Chris Siden <christopher.siden@delphix.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
https://www.illumos.org/issues/2882https://www.illumos.org/issues/2883https://www.illumos.org/issues/2900illumos/illumos-gate@4445fffbbb
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1293
Porting notes:
WARNING: This patch changes the user/kernel ABI. That means that
the zfs/zpool utilities built from master are NOT compatible with
the 0.6.2 kernel modules. Ensure you load the matching kernel
modules from master after updating the utilities. Otherwise the
zfs/zpool commands will be unable to interact with your pool and
you will see errors similar to the following:
$ zpool list
failed to read pool configuration: bad address
no pools available
$ zfs list
no datasets available
Add zvol minor device creation to the new zfs_snapshot_nvl function.
Remove the logging of the "release" operation in
dsl_dataset_user_release_sync(). The logging caused a null dereference
because ds->ds_dir is zeroed in dsl_dataset_destroy_sync() and the
logging functions try to get the ds name via the dsl_dataset_name()
function. I've got no idea why this particular code would have worked
in Illumos. This code has subsequently been completely reworked in
Illumos commit 3b2aab1 (3464 zfs synctask code needs restructuring).
Squash some "may be used uninitialized" warning/erorrs.
Fix some printf format warnings for %lld and %llu.
Apply a few spa_writeable() changes that were made to Illumos in
illumos/illumos-gate.git@cd1c8b8 as part of the 3112, 3113, 3114 and
3115 fixes.
Add a missing call to fnvlist_free(nvl) in log_internal() that was added
in Illumos to fix issue 3085 but couldn't be ported to ZoL at the time
(zfsonlinux/zfs@9e11c73) because it depended on future work.
This implements vdev_bdev_database_check(). It alters the detected
sector size of any device listed in a database of drives known to lie
about their physical sector sizes.
This is based on "6931570 Add flash devices' VID/PID to disk table to
advertising 4K physical sector size" from Open Solaris and on
sg_simple4.c from sg3_utils. About two dozen lines are taken from
sg_simple4.c, which is GPLv2 licensed. However, sg_simple4.c is
analogous to a Hello World program and is safe for us to use. We
requested that Douglas Gilbert, the author of sg_simple4.c, confirm that
this is the case. A cutdown version of his response is as follows:
```
I would consider a SCSI INQUIRY example using the Linux sg
driver interface (also written by me) as the equivalent of an
"hello world" program in C.
```
The database was created with the help of the freenode and ZFSOnLinux
communities.
Some notes:
1. The following drives both were confirmed to lie via reports in IRC
and they contain capacity information in their identifiers:
INTEL SSDSA2M080
INTEL SSDSA2M160
M4-CT256M4SSD2
WDC WD15EARS-00S
WDC WD15EARS-00Z
WDC WD20EARS-00M
The identifiers for different capacity models were extrapolated and
added under the assumption that those models also lie. Google was used
to verify that the extrapolated drive identifiers existed prior to their
inclusion.
2. The OCZ-VERTEX2 3.5 identifer applies to two drives that differ
solely in page size (and slightly in capacity). One uses 4096-byte pages
and the other uses 8192-byte pages. Both are set to use 8192-byte pages.
We could detect the page size by checking the capacity, but that would
unnecessarily complicate the code.
3. It is possible for updated drive firmware to correctly report the
sector size. There were reports of a few advanced format drives doing
that. One report stated that the vendor changed the identification
string while another was unclear on this. Both reports involved WDC
models.
4. Google was used to determine the size of pages in the listed flash
devices. Reports of 8192-byte pages took precedence over reports of
4096-byte pages.
5. Devices behind USB adapters can have their identification strings
altered. Identification strings obtained across USB adapters are
omitted and no attempt is made to correct for alterations made by USB
adapters when doing comparisons against the database. Two entries in the
Open Solaris database that appear to have been altered by a USB
adapter were omitted.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1652
For the same reasons it's used in libzfs_init(), this was just
overlooked because zinject gets minimal use.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1498
3098 zfs userspace/groupspace fail without saying why when run as non-root
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
References:
https://www.illumos.org/issues/3098illumos/illumos-gate@70f56fa693
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1596
Due to an uninitialized variable it was possible for the command
'zpool list -H' to return a non-zero error when there are no pools.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1605
The FreeBSD implementation of zfs adds the 'zpool labelclear'
command. Since this functionality is helpful and straight
forward to add it is being included in ZoL.
References:
freebsd/freebsd@119a041dc9
Ported-by: Dmitry Khasanov <pik4ez@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1126
If the znode has SA xattrs, display them following the other
standard attributes. The format used is similar to that used
when listing the contents of a ZAP. It is as follows:
$ zdb -vvv <pool>/<dataset> <object>
...
SA xattrs: <size> bytes, <number> entries
<name1> = <value1>
<name2> = <value2>
...
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1581
Make sure that buffer is aligned to 512 bytes on linux so that
pread call combined with O_DIRECT does not return EINVAL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1570
For "zpool events -f" flush stdout to ensure the last zevent
is always printed immediately.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1568
A mount failure was accidentally introduced by commit 0c1171d
which reworked the parse_dataset() function to read pool names
from devices. The error case where a label is read from the
device but the pool name/value pair doesn't exist was not
handled properly. In this case we should fall back to the
previous behavior.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1560
cburroughs
Richard Yao
Brian Behlendorf
Patrik Greco
Ned Bass
Tim Chase
Matthew Thode
Michael Kjorling
John Wren Kennedy
renelson
Simon Guest
Yuri Pankov
Maximilian Mehnert
George Wilson
Matthew Ahrens
Keith M Wesolowski
Steven Hartland
Will Andrews
Ralf Ertzinger
Steven Hartland
Turbo Fredriksson
Christer Ekholm
Dmitry Khasanov
Mike Leddy
Craig Loomis