OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
Project quota is a new ZFS system space/object usage accounting
and enforcement mechanism. Similar as user/group quota, project
quota is another dimension of system quota. It bases on the new
object attribute - project ID.
Project ID is a numerical value to indicate to which project an
object belongs. An object only can belong to one project though
you (the object owner or privileged user) can change the object
project ID via 'chattr -p' or 'zfs project [-s] -p' explicitly.
The object also can inherit the project ID from its parent when
created if the parent has the project inherit flag (that can be
set via 'chattr +P' or 'zfs project -s [-p]').
By accounting the spaces/objects belong to the same project, we
can know how many spaces/objects used by the project. And if we
set the upper limit then we can control the spaces/objects that
are consumed by such project. It is useful when multiple groups
and users cooperate for the same project, or a user/group needs
to participate in multiple projects.
Support the following commands and functionalities:
zfs set projectquota@project
zfs set projectobjquota@project
zfs get projectquota@project
zfs get projectobjquota@project
zfs get projectused@project
zfs get projectobjused@project
zfs projectspace
zfs allow projectquota
zfs allow projectobjquota
zfs allow projectused
zfs allow projectobjused
zfs unallow projectquota
zfs unallow projectobjquota
zfs unallow projectused
zfs unallow projectobjused
chattr +/-P
chattr -p project_id
lsattr -p
This patch also supports tree quota based on the project quota via
"zfs project" commands set as following:
zfs project [-d|-r] <file|directory ...>
zfs project -C [-k] [-r] <file|directory ...>
zfs project -c [-0] [-d|-r] [-p id] <file|directory ...>
zfs project [-p id] [-r] [-s] <file|directory ...>
For "df [-i] $DIR" command, if we set INHERIT (project ID) flag on
the $DIR, then the proejct [obj]quota and [obj]used values for the
$DIR's project ID will be shown as the total/free (avail) resource.
Keep the same behavior as EXT4/XFS does.
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by Ned Bass <bass6@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fan Yong <fan.yong@intel.com>
TEST_ZIMPORT_POOLS="zol-0.6.1 zol-0.6.2 master"
Change-Id: Ib4f0544602e03fb61fd46a849d7ba51a6005693c
Closes#6290
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
Suppress incorrect warnings from versions of objtool which are not
aware of x86 EVEX prefix instructions used for AVX512.
module/zfs/vdev_raidz_math_avx512bw.o: warning:
objtool: <func+offset>: can't find jump dest instruction at .text
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6928
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
1. Enable multipath autoreplace support for FMA.
This extends FMA autoreplace to work with multipath disks. This
requires libdevmapper to be installed at build time.
2. Turn on/off fault LEDs when VDEVs become degraded/faulted/online
Set ZED_USE_ENCLOSURE_LEDS=1 in zed.rc to have ZED turn on/off the enclosure
LED for a drive when a drive becomes FAULTED/DEGRADED. Your enclosure must
be supported by the Linux SES driver for this to work. The enclosure LED
scripts work for multipath devices as well. The scripts will clear the LED
when the fault is cleared.
3. Rate limit ZIO delay and checksum events so as not to flood ZED
ZIO delay and checksum events are rate limited to 5/sec in the zfs module.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#2449Closes#3017Closes#5159
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported by: Tony Hutter <hutter2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4185
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45818ee
Porting Notes:
This code is ported on top of the Illumos Crypto Framework code:
b5e030c8db
The list of porting changes includes:
- Copied module/icp/include/sha2/sha2.h directly from illumos
- Removed from module/icp/algs/sha2/sha2.c:
#pragma inline(SHA256Init, SHA384Init, SHA512Init)
- Added 'ctx' to lib/libzfs/libzfs_sendrecv.c:zio_checksum_SHA256() since
it now takes in an extra parameter.
- Added CTASSERT() to assert.h from for module/zfs/edonr_zfs.c
- Added skein & edonr to libicp/Makefile.am
- Added sha512.S. It was generated from sha512-x86_64.pl in Illumos.
- Updated ztest.c with new fletcher_4_*() args; used NULL for new CTX argument.
- In icp/algs/edonr/edonr_byteorder.h, Removed the #if defined(__linux) section
to not #include the non-existant endian.h.
- In skein_test.c, renane NULL to 0 in "no test vector" array entries to get
around a compiler warning.
- Fixup test files:
- Rename <sys/varargs.h> -> <varargs.h>, <strings.h> -> <string.h>,
- Remove <note.h> and define NOTE() as NOP.
- Define u_longlong_t
- Rename "#!/usr/bin/ksh" -> "#!/bin/ksh -p"
- Rename NULL to 0 in "no test vector" array entries to get around a
compiler warning.
- Remove "for isa in $($ISAINFO); do" stuff
- Add/update Makefiles
- Add some userspace headers like stdio.h/stdlib.h in places of
sys/types.h.
- EXPORT_SYMBOL *_Init/*_Update/*_Final... routines in ICP modules.
- Update scripts/zfs2zol-patch.sed
- include <sys/sha2.h> in sha2_impl.h
- Add sha2.h to include/sys/Makefile.am
- Add skein and edonr dirs to icp Makefile
- Add new checksums to zpool_get.cfg
- Move checksum switch block from zfs_secpolicy_setprop() to
zfs_check_settable()
- Fix -Wuninitialized error in edonr_byteorder.h on PPC
- Fix stack frame size errors on ARM32
- Don't unroll loops in Skein on 32-bit to save stack space
- Add memory barriers in sha2.c on 32-bit to save stack space
- Add filetest_001_pos.ksh checksum sanity test
- Add option to write psudorandom data in file_write utility
Authored by: Hans Rosenfeld <hans.rosenfeld@nexenta.com>
Reviewed by: Dan Fields <dan.fields@nexenta.com>
Reviewed by: Josef Sipek <josef.sipek@nexenta.com>
Reviewed by: Richard Elling <richard.elling@gmail.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Signed-off-by: Don Brady <don.brady@intel.com>
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/5997
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/1437283
Porting Notes:
In addition to the OpenZFS changes this patch realigns the events
with those found in OpenZFS.
Events which would be logged as sysevents on illumos have been
been mapped to the 'sysevent' class for Linux. In addition, several
subclass names have been changed to match what is used in OpenZFS.
In all cases this means a '.' was changed to an '_' in the subclass.
The scripts provided by ZoL have been updated, however users which
provide scripts for any of the following events will need to rename
them based on the new subclass names.
ereport.fs.zfs.config.sync sysevent.fs.zfs.config_sync
ereport.fs.zfs.zpool.destroy sysevent.fs.zfs.pool_destroy
ereport.fs.zfs.zpool.reguid sysevent.fs.zfs.pool_reguid
ereport.fs.zfs.vdev.remove sysevent.fs.zfs.vdev_remove
ereport.fs.zfs.vdev.clear sysevent.fs.zfs.vdev_clear
ereport.fs.zfs.vdev.check sysevent.fs.zfs.vdev_check
ereport.fs.zfs.vdev.spare sysevent.fs.zfs.vdev_spare
ereport.fs.zfs.vdev.autoexpand sysevent.fs.zfs.vdev_autoexpand
ereport.fs.zfs.resilver.start sysevent.fs.zfs.resilver_start
ereport.fs.zfs.resilver.finish sysevent.fs.zfs.resilver_finish
ereport.fs.zfs.scrub.start sysevent.fs.zfs.scrub_start
ereport.fs.zfs.scrub.finish sysevent.fs.zfs.scrub_finish
ereport.fs.zfs.bootfs.vdev.attach sysevent.fs.zfs.bootfs_vdev_attach
A port of the Illumos Crypto Framework to a Linux kernel module (found
in module/icp). This is needed to do the actual encryption work. We cannot
use the Linux kernel's built in crypto api because it is only exported to
GPL-licensed modules. Having the ICP also means the crypto code can run on
any of the other kernels under OpenZFS. I ended up porting over most of the
internals of the framework, which means that porting over other API calls (if
we need them) should be fairly easy. Specifically, I have ported over the API
functions related to encryption, digests, macs, and crypto templates. The ICP
is able to use assembly-accelerated encryption on amd64 machines and AES-NI
instructions on Intel chips that support it. There are place-holder
directories for similar assembly optimizations for other architectures
(although they have not been written).
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4329
This is a new implementation of RAIDZ1/2/3 routines using x86_64
scalar, SSE, and AVX2 instruction sets. Included are 3 parity
generation routines (P, PQ, and PQR) and 7 reconstruction routines,
for all RAIDZ level. On module load, a quick benchmark of supported
routines will select the fastest for each operation and they will
be used at runtime. Original implementation is still present and
can be selected via module parameter.
Patch contains:
- specialized gen/rec routines for all RAIDZ levels,
- new scalar raidz implementation (unrolled),
- two x86_64 SIMD implementations (SSE and AVX2 instructions sets),
- fastest routines selected on module load (benchmark).
- cmd/raidz_test - verify and benchmark all implementations
- added raidz_test to the ZFS Test Suite
New zfs module parameters:
- zfs_vdev_raidz_impl (str): selects the implementation to use. On
module load, the parameter will only accept first 3 options, and
the other implementations can be set once module is finished
loading. Possible values for this option are:
"fastest" - use the fastest math available
"original" - use the original raidz code
"scalar" - new scalar impl
"sse" - new SSE impl if available
"avx2" - new AVX2 impl if available
See contents of `/sys/module/zfs/parameters/zfs_vdev_raidz_impl` to
get the list of supported values. If an implementation is not supported
on the system, it will not be shown. Currently selected option is
enclosed in `[]`.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4328
ZFS allows for specific permissions to be delegated to normal users
with the `zfs allow` and `zfs unallow` commands. In addition, non-
privileged users should be able to run all of the following commands:
* zpool [list | iostat | status | get]
* zfs [list | get]
Historically this functionality was not available on Linux. In order
to add it the secpolicy_* functions needed to be implemented and mapped
to the equivalent Linux capability. Only then could the permissions on
the `/dev/zfs` be relaxed and the internal ZFS permission checks used.
Even with this change some limitations remain. Under Linux only the
root user is allowed to modify the namespace (unless it's a private
namespace). This means the mount, mountpoint, canmount, unmount,
and remount delegations cannot be supported with the existing code. It
may be possible to add this functionality in the future.
This functionality was validated with the cli_user and delegation test
cases from the ZFS Test Suite. These tests exhaustively verify each
of the supported permissions which can be delegated and ensures only
an authorized user can perform it.
Two minor bug fixes were required for test-running.py. First, the
Timer() object cannot be safely created in a `try:` block when there
is an unconditional `finally` block which references it. Second,
when running as a normal user also check for scripts using the
both the .ksh and .sh suffixes.
Finally, existing users who are simulating delegations by setting
group permissions on the /dev/zfs device should revert that
customization when updating to a version with this change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#362Closes#434Closes#4100Closes#4394Closes#4410Closes#4487
New functionality:
- Preserves existing scalar implementation.
- Adds AVX2 optimized Fletcher-4 computation.
- Fastest routines selected on module load (benchmark).
- Test case for Fletcher-4 added to ztest.
New zcommon module parameters:
- zfs_fletcher_4_impl (str): selects the implementation to use.
"fastest" - use the fastest version available
"cycle" - cycle trough all available impl for ztest
"scalar" - use the original version
"avx2" - new AVX2 implementation if available
Performance comparison (Intel i7 CPU, 1MB data buffers):
- Scalar: 4216 MB/s
- AVX2: 14499 MB/s
See contents of `/sys/module/zcommon/parameters/zfs_fletcher_4_impl`
to get list of supported values. If an implementation is not supported
on the system, it will not be shown. Currently selected option is
enclosed in `[]`.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4330
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Ported by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/6531
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/97e8130
Porting notes:
- Added new IO delay tracepoints, and moved common ZIO tracepoint macros
to a new trace_common.h file.
- Used zio_delay_taskq() in place of OpenZFS's timeout_generic() function.
- Updated zinject man page
- Updated zpool_scrub test files
In order to remove the HAVE_PN_UTILS wrappers the pn_alloc() and
pn_free() functions must be implemented. The existing illumos
implementation were used for this purpose.
The `flags` argument which was used in places wrapped by the
HAVE_PN_UTILS condition has beed added back to zfs_remove() and
zfs_link() functions. This removes a small point of divergence
between the ZoL code and upstream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4522
Add the required kernel side infrastructure to parse arbitrary
mount options. This enables us to support temporary mount
options in largely the same way it is handled on other platforms.
See the 'Temporary Mount Point Properties' section of zfs(8)
for complete details.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#985Closes#3351
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Porting notes and other significant code changes:
The illumos 5368 patch (ARC should cache more metadata), which
was never picked up by ZoL, is mostly reverted by this patch.
Since ZoL relies on the kernel asynchronously calling the shrinker to
actually reap memory, the shrinker wakes up arc_reclaim_waiters_cv every
time it runs.
The arc_adapt_thread() function no longer calls arc_do_user_evicts()
since the newly-added arc_user_evicts_thread() calls it periodically.
Notable conflicting ZoL commits which conflicted with this patch or
whose effects are either duplicated or un-done by this patch:
302f753 - Integrate ARC more tightly with Linux
39e055c - Adjust arc_p based on "bytes" in arc_shrink
f521ce1 - Allow "arc_p" to drop to zero or grow to "arc_c"
77765b5 - Remove "arc_meta_used" from arc_adjust calculation
94520ca - Prune metadata from ghost lists in arc_adjust_meta
Trace support for multilist_insert() and multilist_remove() has been
added and produces the following output:
fio-12498 [077] .... 112936.448324: zfs_multilist__insert: ml { offset 240 numsublists 80 sublistidx 63 }
fio-12498 [077] .... 112936.448347: zfs_multilist__remove: ml { offset 240 numsublists 80 sublistidx 29 }
The following arcstats have been removed:
recycle_miss - Used by arcstat.py and arc_summary.py, both of which
have been updated appropriately.
l2_writes_hdr_miss
The following arcstats have been added:
evict_not_enough - Number of times arc_evict_state() was unable to
evict enough buffers to reach its target amount.
evict_l2_skip - Number of times arc_evict_hdr() skipped eviction
because it was being written to the l2arc.
l2_writes_lock_retry - Replaces l2_writes_hdr_miss. Number of times
l2arc_write_done() failed to acquire hash_lock (and re-tries).
arc_meta_min - Shows the value of the zfs_arc_meta_min module
parameter (see below).
The "index" column of the "dbuf" kstat has been removed since it doesn't
have a direct analog in the new multilist scheme. Additional multilist-
related stats could be added in the future but would likely require
extensions to the mulilist API.
The following module parameters have been added:
zfs_arc_evict_batch_limit - Number of ARC headers to free per sub-list
before moving on to the next sub-list.
zfs_arc_meta_min - Enforce a floor on the amount of metadata in
the ARC.
zfs_arc_num_sublists_per_state - Number of multilist sub-lists per
ARC state.
zfs_arc_overflow_shift - Controls amount by which the ARC must exceed
the target size to be considered "overflowing".
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov
Older versions of GCC (e.g. GCC 4.4.7 on RHEL6) do not allow duplicate
typedef declarations with the same type. The trace.h header contains
some typedefs to avoid 'unknown type' errors for C files that haven't
declared the type in question. But this causes build failures for C
files that have already declared the type. Newer versions of GCC (e.g.
v4.6) allow duplicate typedefs with the same type unless pedantic error
checking is in force. To support the older versions we need to remove
the duplicate typedefs.
Removal of the typedefs means we can't built tracepoints code using
those types unless the required headers have been included. To
facilitate this, all tracepoint event declarations have been moved out
of trace.h into separate headers. Each new header is explicitly included
from the C file that uses the events defined therein. The trace.h header
is still indirectly included form zfs_context.h and provides the
implementation of the dprintf(), dbgmsg(), and SET_ERROR() interfaces.
This makes those interfaces readily available throughout the code base.
The macros that redefine DTRACE_PROBE* to use Linux tracepoints are also
still provided by trace.h, so it is a prerequisite for the other
trace_*.h headers.
These new Linux implementation-specific headers do introduce a small
divergence from upstream ZFS in several core C files, but this should
not present a significant maintenance burden.
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2953
This patch leverages Linux tracepoints from within the ZFS on Linux
code base. It also refactors the debug code to bring it back in sync
with Illumos.
The information exported via tracepoints can be used for a variety of
reasons (e.g. debugging, tuning, general exploration/understanding,
etc). It is advantageous to use Linux tracepoints as the mechanism to
export this kind of information (as opposed to something else) for a
number of reasons:
* A number of external tools can make use of our tracepoints
"automatically" (e.g. perf, systemtap)
* Tracepoints are designed to be extremely cheap when disabled
* It's one of the "accepted" ways to export this kind of
information; many other kernel subsystems use tracepoints too.
Unfortunately, though, there are a few caveats as well:
* Linux tracepoints appear to only be available to GPL licensed
modules due to the way certain kernel functions are exported.
Thus, to actually make use of the tracepoints introduced by this
patch, one might have to patch and re-compile the kernel;
exporting the necessary functions to non-GPL modules.
* Prior to upstream kernel version v3.14-rc6-30-g66cc69e, Linux
tracepoints are not available for unsigned kernel modules
(tracepoints will get disabled due to the module's 'F' taint).
Thus, one either has to sign the zfs kernel module prior to
loading it, or use a kernel versioned v3.14-rc6-30-g66cc69e or
newer.
Assuming the above two requirements are satisfied, lets look at an
example of how this patch can be used and what information it exposes
(all commands run as 'root'):
# list all zfs tracepoints available
$ ls /sys/kernel/debug/tracing/events/zfs
enable filter zfs_arc__delete
zfs_arc__evict zfs_arc__hit zfs_arc__miss
zfs_l2arc__evict zfs_l2arc__hit zfs_l2arc__iodone
zfs_l2arc__miss zfs_l2arc__read zfs_l2arc__write
zfs_new_state__mfu zfs_new_state__mru
# enable all zfs tracepoints, clear the tracepoint ring buffer
$ echo 1 > /sys/kernel/debug/tracing/events/zfs/enable
$ echo 0 > /sys/kernel/debug/tracing/trace
# import zpool called 'tank', inspect tracepoint data (each line was
# truncated, they're too long for a commit message otherwise)
$ zpool import tank
$ cat /sys/kernel/debug/tracing/trace | head -n35
# tracer: nop
#
# entries-in-buffer/entries-written: 1219/1219 #P:8
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
lt-zpool-30132 [003] .... 91344.200050: zfs_arc__miss: hdr...
z_rd_int/0-30156 [003] .... 91344.200611: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.201173: zfs_arc__miss: hdr...
z_rd_int/1-30157 [003] .... 91344.201756: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.201795: zfs_arc__miss: hdr...
z_rd_int/2-30158 [003] .... 91344.202099: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202126: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202130: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202134: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202146: zfs_arc__miss: hdr...
z_rd_int/3-30159 [003] .... 91344.202457: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202484: zfs_arc__miss: hdr...
z_rd_int/4-30160 [003] .... 91344.202866: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202891: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.203034: zfs_arc__miss: hdr...
z_rd_iss/1-30149 [001] .... 91344.203749: zfs_new_state__mru...
lt-zpool-30132 [001] .... 91344.203789: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.203878: zfs_arc__miss: hdr...
z_rd_iss/3-30151 [001] .... 91344.204315: zfs_new_state__mru...
lt-zpool-30132 [001] .... 91344.204332: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204337: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204352: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204356: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204360: zfs_arc__hit: hdr ...
To highlight the kind of detailed information that is being exported
using this infrastructure, I've taken the first tracepoint line from the
output above and reformatted it such that it fits in 80 columns:
lt-zpool-30132 [003] .... 91344.200050: zfs_arc__miss:
hdr {
dva 0x1:0x40082
birth 15491
cksum0 0x163edbff3a
flags 0x640
datacnt 1
type 1
size 2048
spa 3133524293419867460
state_type 0
access 0
mru_hits 0
mru_ghost_hits 0
mfu_hits 0
mfu_ghost_hits 0
l2_hits 0
refcount 1
} bp {
dva0 0x1:0x40082
dva1 0x1:0x3000e5
dva2 0x1:0x5a006e
cksum 0x163edbff3a:0x75af30b3dd6:0x1499263ff5f2b:0x288bd118815e00
lsize 2048
} zb {
objset 0
object 0
level -1
blkid 0
}
For the specific tracepoint shown here, 'zfs_arc__miss', data is
exported detailing the arc_buf_hdr_t (hdr), blkptr_t (bp), and
zbookmark_t (zb) that caused the ARC miss (down to the exact DVA!).
This kind of precise and detailed information can be extremely valuable
when trying to answer certain kinds of questions.
For anybody unfamiliar but looking to build on this, I found the XFS
source code along with the following three web links to be extremely
helpful:
* http://lwn.net/Articles/379903/
* http://lwn.net/Articles/381064/
* http://lwn.net/Articles/383362/
I should also node the more "boring" aspects of this patch:
* The ZFS_LINUX_COMPILE_IFELSE autoconf macro was modified to
support a sixth paramter. This parameter is used to populate the
contents of the new conftest.h file. If no sixth parameter is
provided, conftest.h will be empty.
* The ZFS_LINUX_TRY_COMPILE_HEADER autoconf macro was introduced.
This macro is nearly identical to the ZFS_LINUX_TRY_COMPILE macro,
except it has support for a fifth option that is then passed as
the sixth parameter to ZFS_LINUX_COMPILE_IFELSE.
These autoconf changes were needed to test the availability of the Linux
tracepoint macros. Due to the odd nature of the Linux tracepoint macro
API, a separate ".h" must be created (the path and filename is used
internally by the kernel's define_trace.h file).
* The HAVE_DECLARE_EVENT_CLASS autoconf macro was introduced. This
is to determine if we can safely enable the Linux tracepoint
functionality. We need to selectively disable the tracepoint code
due to the kernel exporting certain functions as GPL only. Without
this check, the build process will fail at link time.
In addition, the SET_ERROR macro was modified into a tracepoint as well.
To do this, the 'sdt.h' file was moved into the 'include/sys' directory
and now contains a userspace portion and a kernel space portion. The
dprintf and zfs_dbgmsg* interfaces are now implemented as tracepoint as
well.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add a new file named arc_impl.h and move a few internal
ARC structure definitions into this file. This is
needed in order to allow the Linux tracepoint functions to grub
around in the internals of these structures.
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This is the upstream component of work that enables preliminary support
for building Gentoo's ZFS packaging on other Linux systems via Gentoo
Prefix.
Signed-off-by: Richard Yao <richard.yao@clusterhq.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #2641
4757 ZFS embedded-data block pointers ("zero block compression")
4913 zfs release should not be subject to space checks
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4757https://www.illumos.org/issues/4913https://github.com/illumos/illumos-gate/commit/5d7b4d4
Porting notes:
For compatibility with the fastpath code the zio_done() function
needed to be updated. Because embedded-data block pointers do
not require DVAs to be allocated the associated vdevs will not
be marked and therefore should not be unmarked.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2544
4101 metaslab_debug should allow for fine-grained control
4102 space_maps should store more information about themselves
4103 space map object blocksize should be increased
4105 removing a mirrored log device results in a leaked object
4106 asynchronously load metaslab
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Sebastien Roy <seb@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Prior to this patch, space_maps were preferred solely based on the
amount of free space left in each. Unfortunately, this heuristic didn't
contain any information about the make-up of that free space, which
meant we could keep preferring and loading a highly fragmented space map
that wouldn't actually have enough contiguous space to satisfy the
allocation; then unloading that space_map and repeating the process.
This change modifies the space_map's to store additional information
about the contiguous space in the space_map, so that we can use this
information to make a better decision about which space_map to load.
This requires reallocating all space_map objects to increase their
bonus buffer size sizes enough to fit the new metadata.
The above feature can be enabled via a new feature flag introduced by
this change: com.delphix:spacemap_histogram
In addition to the above, this patch allows the space_map block size to
be increase. Currently the block size is set to be 4K in size, which has
certain implications including the following:
* 4K sector devices will not see any compression benefit
* large space_maps require more metadata on-disk
* large space_maps require more time to load (typically random reads)
Now the space_map block size can adjust as needed up to the maximum size
set via the space_map_max_blksz variable.
A bug was fixed which resulted in potentially leaking an object when
removing a mirrored log device. The previous logic for vdev_remove() did
not deal with removing top-level vdevs that are interior vdevs (i.e.
mirror) correctly. The problem would occur when removing a mirrored log
device, and result in the DTL space map object being leaked; because
top-level vdevs don't have DTL space map objects associated with them.
References:
https://www.illumos.org/issues/4101https://www.illumos.org/issues/4102https://www.illumos.org/issues/4103https://www.illumos.org/issues/4105https://www.illumos.org/issues/4106https://github.com/illumos/illumos-gate/commit/0713e23
Porting notes:
A handful of kmem_alloc() calls were converted to kmem_zalloc(). Also,
the KM_PUSHPAGE and TQ_PUSHPAGE flags were used as necessary.
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2488
4045 zfs write throttle & i/o scheduler performance work
1. The ZFS i/o scheduler (vdev_queue.c) now divides i/os into 5 classes: sync
read, sync write, async read, async write, and scrub/resilver. The scheduler
issues a number of concurrent i/os from each class to the device. Once a class
has been selected, an i/o is selected from this class using either an elevator
algorithem (async, scrub classes) or FIFO (sync classes). The number of
concurrent async write i/os is tuned dynamically based on i/o load, to achieve
good sync i/o latency when there is not a high load of writes, and good write
throughput when there is. See the block comment in vdev_queue.c (reproduced
below) for more details.
2. The write throttle (dsl_pool_tempreserve_space() and
txg_constrain_throughput()) is rewritten to produce much more consistent delays
when under constant load. The new write throttle is based on the amount of
dirty data, rather than guesses about future performance of the system. When
there is a lot of dirty data, each transaction (e.g. write() syscall) will be
delayed by the same small amount. This eliminates the "brick wall of wait"
that the old write throttle could hit, causing all transactions to wait several
seconds until the next txg opens. One of the keys to the new write throttle is
decrementing the amount of dirty data as i/o completes, rather than at the end
of spa_sync(). Note that the write throttle is only applied once the i/o
scheduler is issuing the maximum number of outstanding async writes. See the
block comments in dsl_pool.c and above dmu_tx_delay() (reproduced below) for
more details.
This diff has several other effects, including:
* the commonly-tuned global variable zfs_vdev_max_pending has been removed;
use per-class zfs_vdev_*_max_active values or zfs_vdev_max_active instead.
* the size of each txg (meaning the amount of dirty data written, and thus the
time it takes to write out) is now controlled differently. There is no longer
an explicit time goal; the primary determinant is amount of dirty data.
Systems that are under light or medium load will now often see that a txg is
always syncing, but the impact to performance (e.g. read latency) is minimal.
Tune zfs_dirty_data_max and zfs_dirty_data_sync to control this.
* zio_taskq_batch_pct = 75 -- Only use 75% of all CPUs for compression,
checksum, etc. This improves latency by not allowing these CPU-intensive tasks
to consume all CPU (on machines with at least 4 CPU's; the percentage is
rounded up).
--matt
APPENDIX: problems with the current i/o scheduler
The current ZFS i/o scheduler (vdev_queue.c) is deadline based. The problem
with this is that if there are always i/os pending, then certain classes of
i/os can see very long delays.
For example, if there are always synchronous reads outstanding, then no async
writes will be serviced until they become "past due". One symptom of this
situation is that each pass of the txg sync takes at least several seconds
(typically 3 seconds).
If many i/os become "past due" (their deadline is in the past), then we must
service all of these overdue i/os before any new i/os. This happens when we
enqueue a batch of async writes for the txg sync, with deadlines 2.5 seconds in
the future. If we can't complete all the i/os in 2.5 seconds (e.g. because
there were always reads pending), then these i/os will become past due. Now we
must service all the "async" writes (which could be hundreds of megabytes)
before we service any reads, introducing considerable latency to synchronous
i/os (reads or ZIL writes).
Notes on porting to ZFS on Linux:
- zio_t gained new members io_physdone and io_phys_children. Because
object caches in the Linux port call the constructor only once at
allocation time, objects may contain residual data when retrieved
from the cache. Therefore zio_create() was updated to zero out the two
new fields.
- vdev_mirror_pending() relied on the depth of the per-vdev pending queue
(vq->vq_pending_tree) to select the least-busy leaf vdev to read from.
This tree has been replaced by vq->vq_active_tree which is now used
for the same purpose.
- vdev_queue_init() used the value of zfs_vdev_max_pending to determine
the number of vdev I/O buffers to pre-allocate. That global no longer
exists, so we instead use the sum of the *_max_active values for each of
the five I/O classes described above.
- The Illumos implementation of dmu_tx_delay() delays a transaction by
sleeping in condition variable embedded in the thread
(curthread->t_delay_cv). We do not have an equivalent CV to use in
Linux, so this change replaced the delay logic with a wrapper called
zfs_sleep_until(). This wrapper could be adopted upstream and in other
downstream ports to abstract away operating system-specific delay logic.
- These tunables are added as module parameters, and descriptions added
to the zfs-module-parameters.5 man page.
spa_asize_inflation
zfs_deadman_synctime_ms
zfs_vdev_max_active
zfs_vdev_async_write_active_min_dirty_percent
zfs_vdev_async_write_active_max_dirty_percent
zfs_vdev_async_read_max_active
zfs_vdev_async_read_min_active
zfs_vdev_async_write_max_active
zfs_vdev_async_write_min_active
zfs_vdev_scrub_max_active
zfs_vdev_scrub_min_active
zfs_vdev_sync_read_max_active
zfs_vdev_sync_read_min_active
zfs_vdev_sync_write_max_active
zfs_vdev_sync_write_min_active
zfs_dirty_data_max_percent
zfs_delay_min_dirty_percent
zfs_dirty_data_max_max_percent
zfs_dirty_data_max
zfs_dirty_data_max_max
zfs_dirty_data_sync
zfs_delay_scale
The latter four have type unsigned long, whereas they are uint64_t in
Illumos. This accommodates Linux's module_param() supported types, but
means they may overflow on 32-bit architectures.
The values zfs_dirty_data_max and zfs_dirty_data_max_max are the most
likely to overflow on 32-bit systems, since they express physical RAM
sizes in bytes. In fact, Illumos initializes zfs_dirty_data_max_max to
2^32 which does overflow. To resolve that, this port instead initializes
it in arc_init() to 25% of physical RAM, and adds the tunable
zfs_dirty_data_max_max_percent to override that percentage. While this
solution doesn't completely avoid the overflow issue, it should be a
reasonable default for most systems, and the minority of affected
systems can work around the issue by overriding the defaults.
- Fixed reversed logic in comment above zfs_delay_scale declaration.
- Clarified comments in vdev_queue.c regarding when per-queue minimums take
effect.
- Replaced dmu_tx_write_limit in the dmu_tx kstat file
with dmu_tx_dirty_delay and dmu_tx_dirty_over_max. The first counts
how many times a transaction has been delayed because the pool dirty
data has exceeded zfs_delay_min_dirty_percent. The latter counts how
many times the pool dirty data has exceeded zfs_dirty_data_max (which
we expect to never happen).
- The original patch would have regressed the bug fixed in
zfsonlinux/zfs@c418410, which prevented users from setting the
zfs_vdev_aggregation_limit tuning larger than SPA_MAXBLOCKSIZE.
A similar fix is added to vdev_queue_aggregate().
- In vdev_queue_io_to_issue(), dynamically allocate 'zio_t search' on the
heap instead of the stack. In Linux we can't afford such large
structures on the stack.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Ned Bass <bass6@llnl.gov>
Reviewed by: Brendan Gregg <brendan.gregg@joyent.com>
Approved by: Robert Mustacchi <rm@joyent.com>
References:
http://www.illumos.org/issues/4045illumos/illumos-gate@69962b5647
Ported-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1913
Install the common zfs kernel development headers under
/usr/src/zfs-<version>/ rather than in a kernel specific
directory. The kernel specific build products such as
zfs_config.h and Modules.symvers are left installed under
/usr/src/zfs-<version>/<kernel>.
This was done to be consistent with where dkms expects
kernel module source to be packaged. It also allows for
a common zfs-kmod-devel package which includes the headers,
and per-kernel zfs-kmod-devel-<kernel> packages.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
When the original build system code was added the release
component was accidentally omited from the development header
install path. This patch adds the missing path component so
it's always clear exactly what release your compiling against.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
With the removal of the minimal xvattr support from the spl this
support needs to be replaced in the zfs package. This is fairly
easily accomplished by directly adding portions of the sys/vnode.h
header from OpenSolaris. These xvattr additions have been placed
in the sys/xvattr.h header file and included as needed where simply
a sys/vnode.h was included before.
In additon to the xvattr types and helper macros two functions
were also included. The xva_init() and xva_getxoptattr() functions
were included as static inline functions in xvattr.h. They are
simple enough and it was simpler to place them here rather than
in their own .c file.
For legacy reasons the zvol.c and vdev_disk.c Linux compatibility
code ended up in sys/blkdev.h and sys/vdev_disk.h headers. While
there are worse places for this code to live it should be in a
linux/blkdev_compat.h header. This change moves this block device
Linux compatibility code in to the linux/blkdev_compat.h header
and updates all the correct #include locations. This is not a
functional change or bug fix, it is just code cleanup.
The Linux specific file operations have all been located in the
file zpl_file.c. These functions primarily rely on the reworked
zfs_* functions to do their job. They are also responsible for
converting the possible Solaris style error codes to negative
Linux errors.
This first zpl_* commit also includes a common zpl.h header with
minimal entries to register the Linux specific hooks. In also
adds all the new zpl_* file to the Makefile.in. This is not a
standalone commit, you required the following zpl_* commits.
This code is used for snapshot and heavily leverages Solaris
functionality we do not want to reimplement. These files have
been removed, including references to them, and will be replaced
by a zfs_snap.c/zpl_snap.c implementation which handles snapshots.
This code originates in OpenSolaris and was modified by KQ Infotech
to be compatible with Linux. While supporting uios in the short
term is useful to get something working this is not an abstraction
we want to keep. This code is expected to be short lived and
removed as soon as all the remaining uio based APIs and updated.
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
Matthew Ahrens
Nasf-Fan
Chris Williamson
Brian Behlendorf
Tom Caputi
Olaf Faaland
David Quigley
Tony Hutter
Hans Rosenfeld
Gvozden Neskovic
Jinshan Xiong
Paul Dagnelie
Prakash Surya
Ned Bass
Prakash Surya
Richard Yao
George Wilson
Christopher Siden