Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
Users were seeing floods of `config_sync` events when autoexpand was
enabled. This happened because all "disk status change" udev events
invoke the autoexpand codepath, which calls zpool_relabel_disk(),
which in turn cause another "disk status change" event to happen,
in a feedback loop. Note that "disk status change" happens every time
a user calls close() on a block device.
This commit breaks the feedback loop by only allowing an autoexpand
to happen if the disk actually changed size.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes: #7132Closes: #7366Closes#13729
This commit fixes a minor spacing issue caused when
enumerating vdev names, which originated from #13031
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Akash B <akash-b@hpe.com>
Signed-off-by: Samuel Wycliffe <samuelwycliffe@gmail.com>
Closes#13811
We tried replacing an NVMe drive using autoreplace, only
to see zed reject it with:
zed[27955]: zed_udev_monitor: /dev/nvme5n1 no devid source
This happened because ZED saw that ID_BUS was not set by udev
for the NVMe drive, and thus didn't think it was "real drive".
This commit allows NVMe drives to be autoreplaced even if
ID_BUS is not set.
Reviewed-by: Don Brady <don.brady@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13512Closes#13646
libudev will sometimes falsely identify an 'atari' partition on a
blank disk, preventing it from being used in an autoreplace. This
seems to be a known issue. The workaround is to just ignore the
fake partition and continue with the autoreplace.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13497Closes#13632
When the -p option is used, a list of floats is passed to sep.join(),
which expects strings. Fix this by converting each value to a string.
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Roberto Ricci <ricci@disroot.org>
Closes#12916Closes#13767
zdb -d <pool>/<objset ID> does not work when
other command line arguments are included i.e.
zdb -U <cachefile> -d <pool>/<objset ID>
This change fixes the command line parsing
to handle this situation. Also fix issue
where zdb -r <dataset> <file> does not handle
the root <dataset> of the pool. Introduce -N
option to force <objset ID> to be interpreted
as a numeric objsetID.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12845Closes#12944
Switch to using asprintf() to satisfy the compiler and resolve the
potential format-overflow warning. Not the conditional before the
sprintf() would have prevented this regardless.
cmd/zfs/zfs_project.c: In function ‘zfs_project_handle_dir’:
cmd/zfs/zfs_project.c:241:38: error: ‘/’ directive writing
1 byte into a region of size between 0 and 4352
[-Werror=format-overflow=]
cmd/zfs/zfs_project.c:241:17: note: ‘sprintf’ output between
2 and 4609 bytes into a destination of size 4352
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Extend the buffer slightly resolve the warning.
cmd/zfs/zfs_main.c: In function ‘upgrade_set_callback’:
cmd/zfs/zfs_main.c:2446:22: error: ‘%llu’ directive output
may be truncated writing between 1 and 20 bytes into a
region of size 16 [-Werror=format-truncation=]
cmd/zfs/zfs_main.c:2445:24: note: ‘snprintf’ output between
2 and 21 bytes into a destination of size 16
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
Some minimal MUAs don't support passing the subjects as cmdline option.
This commit checks if "@SUBJECT@" is missing in ZED_EMAIL_OPTS and then
prepends a subject header to the notification message.
Also set a default for ${subject}.
Reviewed-by: Ahelenia Ziemia<C5><84>ska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Daniel Hiepler <d-git@coderdu.de>
Closes#13440
When scrubbing/resilvering a pool it can be counter productive to
cancel the scan and kick of a replace operation to a hot spare
when encountering checksum errors. In this case, the best course
of action is to allow the scrub/resilver to complete as quickly
as possible and to keep the vdevs fully online if possible.
Realistically, this is less of an issue for a RAIDZ since a
traditional resilver must be used and checksums will be verified.
However, this is not the case for a mirror or dRAID pool which is
sequentially resilvered and checksum verification is deferred
until after the replace operation completes.
Regardless, we apply this policy to all pool types since it's
a good idea for all vdevs. Degrading additional vdevs has the
potential to make a bad situation worse. Note the checksum
errors will still be reported as both an event and by
`zpool status`. This change only prevents the ZED from
proactively taking any action.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13499
The SA attribute containing the symlink target does not include a nul
terminator, so when printing the target zdb would sometimes include
garbage at the end of the string.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13482
"When an encrypted zvol is locked the zfs-volume-wait service does not
start. The /sbin/zvol_wait should not wait for links when the volume
has property keystatus=unavailable."
-- https://bugs.launchpad.net/ubuntu/+source/zfs-linux/+bug/1888405
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Thanks: James Dingwall <james-launchpad@dingwall.me.uk>
Signed-off-by: Richard Laager <rlaager@wiktel.com>
Closes#10662
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
We recently had a case where our operators replaced a bad
multipathed disk, only to see it fail to autoreplace. The
zed logs showed that the multipath replacement disk did not pass
the 'is_dm' test in zfs_process_add() even though it should have.
is_dm is set if there exists a sysfs entry for to the
underlying /dev/sd* paths for the multipath disk. It's
possible this path didn't exist due to a race condition where
the sysfs paths weren't created at the time the udev event came
in to zed, but this was never verified.
This patch updates the check to look for udev properties that
indicate if the new autoreplace disk is an empty multipath disk,
rather than looking for the underlying sysfs entries. It also
adds in additional logging, and fixes a bug where zed allowed
you to use an already zfs-formatted disk from another pool
as a multipath auto-replacement disk.
Furthermore, while testing this patch, I also ran across a case
where a force-faulted disk did not have a ZPOOL_CONFIG_PHYS_PATH
entry in its config. This prevented it from being autoreplaced.
I added additional logic to derive the PHYS_PATH from the PATH if
the PATH was a /dev/disk/by-vdev/ path. For example, if PATH
was /dev/disk/by-vdev/L28, then PHYS_PATH would be L28. This is
safe since by-vdev paths represent physical locations and do not
change between boots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13023
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#13154
Using `zfs_mount_at()` gives opportunity to properly propagate
mountopts from what's stored in a pool to the `mount(2)` syscall
invocation. It fixes cases when mount options are set to incorrect
values and rectification is impossible (e. g. Linux initrd boot
sequence in #7947).
Moved debug information printing after all variables are
initialized - printed text reflects what is passed to `mount(2)`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Issue #7947Closes#13021
This commit adds enumerated names to disambiguate between the
different vdevs. Previously only 'zpool status' showed enumerated
vdev names, now 'zpool list -v' and 'zpool iostat -v' also shows
the enumerated vdev names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12510Closes#13031
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
`UNAVAIL` is maybe not quite as concerning as `DEGRADED`, but still an
event of notice, in my opinion. For example it is triggered when a
drive goes missing.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Francesco Mazzoli <f@mazzo.li>
Closes#12629Closes#12630
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
Add zed_notify_pushover to zed-functions.sh, along with the necessary
configuration variables in zed.rc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Scott Colby <scott@scolby.com>
Closes#12012
This was discovered when using Discords Slack compatible webhook.
Slack webhooks works without the escape, however Discord rightly refuses
the POST as it contains invalid JSON.
https://discord.com/developers/docs/resources/webhook#execute-slackcompatible-webhook
Valid (while escaping the newline:
```
+ msg_json='{"text": "*ZFS scrub_finish error for test on quartz*\nZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
```
Invalid (no escape):
```
+ msg_json='{"text": "*ZFS scrub_finish error for test on quartz*
ZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
```
The new line gets rendered and not sent inside the JSON as intended.
```
++ curl -X POST https://discord.com/api/webhooks/{webhook.id}/{webhook.token}/slack --header 'Content-Type: application/json' --data-binary '{"text": "*ZFS scrub_finish error for test on quartz*
ZFS has detected a data error:\n\n eid: 124\n class: scrub_finish\n host: quartz\n time: \n error: \n objid: :\n pool: test\n"}'
+ msg_out='{"message": "Cannot send an empty message", "code": 50006}'
```
Test method:
`root@quartz:/etc/zfs/zed.d# export ZED_ZEDLET_DIR=/etc/zfs/zed.d; export ZEVENT_EID=124; export ZEVENT_SUBCLASS=scrub_finish; export ZEVENT_POOL=test; export ZED_NOTIFY_DATA=1; bash -x ./data-notify.sh`
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Philip Kauffman <philip@kauffman.me>
Closes#13049
The ZED code currently can only turn on the fault LED for
a faulted disk in a JBOD enclosure. This extends support
for faulted NVMe disks as well.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12648Closes#12695
One of our developers noticed a bug in vdev_id where we were incorrectly
sorting PHYs using alphabetical sorting (which usually works) instead
of natural sorting (-v). For example:
[port-0:0]# ls -d phy*
phy-0:10 phy-0:11 phy-0:8 phy-0:9
[port-0:0]# ls -vd phy*
phy-0:8 phy-0:9 phy-0:10 phy-0:11
This fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12699
The vdev_id.conf "enclosure_symlinks" option persistently creates
and maps /dev/by-enclosure symlinks to dynamic /dev/sg* devices.
This patch fixes two issues:
1. The enclosure_symlinks feature was accidentally broken in:
vdev_id: Support daisy-chained JBODs in multipath mode
2. Even when working, the feature numbered the enclosure
sequentially rather than by HBA port number. That meant that
if a port was down or didn't appear in sysfs, then the
enclosure_sumlinks numbers would be numbered wrong.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Arshad Hussain <arshad.hussain@aeoncomputing.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12660
When you create a pool, zfs writes vd->vdev_enc_sysfs_path with the
enclosure sysfs path to the fault LEDs, like:
vdev_enc_sysfs_path = /sys/class/enclosure/0:0:1:0/SLOT8
However, this enclosure path doesn't get updated on successive imports
even if enclosure path to the disk changes. This patch fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11950Closes#12095
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
It turns out that layouts of union bitfields are a pain, and the
current code results in an inconsistent layout between BE and LE
systems, leading to zstd-active datasets on one erroring out on
the other.
Switch everyone over to the LE layout, and add compatibility code
to read both.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12008Closes#12022
This patch allows you to clear the label on offlined disks in an active
pool with `-f`. Previously, labelclear wouldn't let you do that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#12511
Signed-off-by: Anton Gubarkov <anton.gubarkov@gmail.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
`zpool_do_import()` passes `argv[0]`, (optionally) `argv[1]`, and
`pool_specified` to `import_pools()`. If `pool_specified==FALSE`, the
`argv[]` arguments are not used. However, these values may be off the
end of the `argv[]` array, so loading them could dereference unmapped
memory. This error is reported by the asan build:
```
=================================================================
==6003==ERROR: AddressSanitizer: heap-buffer-overflow
READ of size 8 at 0x6030000004a8 thread T0
#0 0x562a078b50eb in zpool_do_import zpool_main.c:3796
#1 0x562a078858c5 in main zpool_main.c:10709
#2 0x7f5115231bf6 in __libc_start_main
#3 0x562a07885eb9 in _start
0x6030000004a8 is located 0 bytes to the right of 24-byte region
allocated by thread T0 here:
#0 0x7f5116ac6b40 in __interceptor_malloc
#1 0x562a07885770 in main zpool_main.c:10699
#2 0x7f5115231bf6 in __libc_start_main
```
This commit passes NULL for these arguments if they are off the end
of the `argv[]` array.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#12339
Use strlcpy instead of problematic strncpy
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#12344
zfs-send(8) claimed in the flags list you could use -pR when sending
a readonly filesystem or volume. You cannot.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12336
Currently, there are several places in zvol_id where the program logic
returns particular errno values, or even particular ioctl return values,
as the program exit status, rather than a straightforward system of
explicit zero on success and explicit nonzero value(s) on failure.
This is problematic for multiple reasons. One particularly interesting
problem that can arise, is that if any of these values happens to have
all 8 least significant bits unset (i.e., it is a positive or negative
multiple of 256), then although the C program sees a nonzero int value
(presumed to be a failure exit status), the actual exit status as seen
by the system is only the bottom 8 bits of that integer: zero.
This can happen in practice, and I have encountered it myself. In a
particularly weird situation, the zvol_open code in the zfs kernel
module was behaving in such a manner that it caused the open() syscall
to fail and for errno to be set to a kernel-private value (ERESTARTSYS,
which happens to be defined as 512). It turns out that 512 is evenly
divisible by 256; or, in other words, its least significant 8 bits are
all-zero. So even though zvol_id believed it was returning a nonzero
(failure) exit status of 512, the system modulo'd that value by 256,
resulting in the actual exit status visible by other programs being 0!
This actually-zero (non-failure) exit status caused problems: udev
believed that the program was operating successfully, when in fact it
was attempting to indicate failure via a nonzero exit status integer.
Combined with another problem, this led to the creation of nonsense
symlinks for zvol dev nodes by udev.
Let's get rid of all this problematic logic, and simply return
EXIT_SUCCESS (0) is everything went fine, and EXIT_FAILURE (1) if
anything went wrong.
Additionally, let's clarify some of the variable names (error is similar
to errno, etc) and clean up the overall program flow a bit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
The zvol_id program is invoked by udev, via a PROGRAM key in the
60-zvol.rules.in rule file, to determine the "pretty" /dev/zvol/*
symlink paths paths that should be generated for each opaquely named
/dev/zd* dev node.
The udev rule uses the PROGRAM key, followed by a SYMLINK+= assignment
containing the %c substitution, to collect the program's stdout and then
"paste" it directly into the name of the symlink(s) to be created.
Unfortunately, as currently written, zvol_id outputs both its intended
output (a single string representing the symlink path that should be
created to refer to the name of the dataset whose /dev/zd* path is
given) AND its error messages (if any) to stdout.
When processing PROGRAM keys (and others, such as IMPORT{program}), udev
uses only the data written to stdout for functional purposes. Any data
written to stderr is used solely for the purposes of logging (if udev's
log_level is set to debug).
The unintended consequence of this is as follows: if zvol_id encounters
an error condition; and then udev fails to halt processing of the
current rule (either because zvol_id didn't return a nonzero exit
status, or because the PROGRAM key in the rule wasn't written properly
to result in a "non-match" condition that would stop the current rule on
a nonzero exit); then udev will create a space-delimited list of symlink
names derived directly from the words of the error message string!
I've observed this exact behavior on my own system, in a situation where
the open() syscall on /dev/zd* dev nodes was failing sporadically (for
reasons that aren't especially relevant here). Because the open() call
failed, zvol_id printed "Unable to open device file: /dev/zd736\n" to
stdout and then exited.
The udev rule finished with SYMLINK+="zvol/%c %c". Assuming a volume
name like pool/foo/bar, this would ordinarily expand to
SYMLINK+="zvol/pool/foo/bar pool/foo/bar"
and would cause symlinks to be created like this:
/dev/zvol/pool/foo/bar -> /dev/zd736
/dev/pool/foo/bar -> /dev/zd736
But because of the combination of error messages being printed to
stdout, and the udev syntax freely accepting a space-delimited sequence
of names in this context, the error message string
"Unable to open device file: /dev/zd736\n"
in reality expanded to
SYMLINK+="zvol/Unable to open device file: /dev/zd736"
which caused the following symlinks to actually be created:
/dev/zvol/Unable -> /dev/zd736
/dev/to -> /dev/zd736
/dev/open -> /dev/zd736
/dev/device -> /dev/zd736
/dev/file: -> /dev/zd736
/dev//dev/zd736 -> /dev/zd736
(And, because multiple zvols had open() syscall errors, multiple zvols
attempted to claim several of those symlink names, resulting in numerous
udev errors and timeouts and general chaos.)
This commit rectifies all this silliness by simply printing error
messages to stderr, as Dennis Ritchie originally intended.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Justin Gottula <justin@jgottula.com>
Closes#12302
This enables ZED to auto-online vdevs that are not wholedisk managed by
ZFS.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Commit 6fc3099 broke the quoting when invoking the mail program, revert
that change.
Signed-off-by: Laurențiu Nicola <lnicola@dend.ro>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
This replaces the generic libspl atomic.c atomics implementation
with one based on builtin gcc atomics. This functionality was added
as an experimental feature in gcc 4.4. Today even CentOS 7 ships
with gcc 4.8 as the default compiler we can make this the default.
Furthermore, the builtin atomics are as good or better than our
hand-rolled implementation so it's reasonable to drop that custom code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11904Closes#12252Closes#12244
Starting in Linux 5.10, trying to write to /dev/{null,zero} errors out.
Prefer to inform people when this happens rather than hoping they guess
what's wrong.
Reviewed-by: Antonio Russo <aerusso@aerusso.net>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #11991
The first warning of a misspelling is a false positive, so we annotate
the script accordingly. As for the x-prefix warnings update the check
to use the conventional '[ -z <string> ]' syntax.
all-syslog.sh:46:47: warning: Possible misspelling: ZEVENT_ZIO_OBJECT
may not be assigned, but ZEVENT_ZIO_OBJSET is. [SC2153]
make_gitrev.sh:53:6: note: Avoid x-prefix in comparisons as it no
longer serves a purpose [SC2268]
man-dates.sh:10:7: note: Avoid x-prefix in comparisons as it no
longer serves a purpose [SC2268]
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12208
This:
(a) improves the error log message,
(b) locks per pool instead of globally,
(c) locks the actual output file instead of /var/lock/zfs-list,
which would otherwise linger there forever (well, still will,
but you can remove it and it won't come back), and
(d) preserves attributes of the output file
instead of reverting them to 0:0 644
It is imperative that the previous commit
("zed-functions.sh: zed_lock(): don't truncate lock")
be included in any series that contains this one
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12042
Akash B
Tony Hutter
Samuel
r-ricci
Paul Zuchowski
Brian Behlendorf
heeplr
Mark Johnston
Richard Laager
наб
Paul Dagnelie
Damian Szuberski
George Amanakis
Francesco Mazzoli
Jorgen Lundman
Scott Colby
Phil Kauffman
shodanshok
Damian Szuberski
Don Brady
Rich Ercolani
Anton Gubarkov
Matthew Ahrens
George Melikov
Justin Gottula
Ryan Moeller
Laurențiu Nicola