PROBLEM
========
The first access to a block incurs a performance penalty on some platforms
(e.g. AWS's EBS, VMware VMDKs). Therefore we recommend that volumes are
"thick provisioned", where supported by the platform (VMware). This can
create a large delay in getting a new virtual machines up and running (or
adding storage to an existing Engine). If the thick provision step is
omitted, write performance will be suboptimal until all blocks on the LUN
have been written.
SOLUTION
=========
This feature introduces a way to 'initialize' the disks at install or in the
background to make sure we don't incur this first read penalty.
When an entire LUN is added to ZFS, we make all space available immediately,
and allow ZFS to find unallocated space and zero it out. This works with
concurrent writes to arbitrary offsets, ensuring that we don't zero out
something that has been (or is in the middle of being) written. This scheme
can also be applied to existing pools (affecting only free regions on the
vdev). Detailed design:
- new subcommand:zpool initialize [-cs] <pool> [<vdev> ...]
- start, suspend, or cancel initialization
- Creates new open-context thread for each vdev
- Thread iterates through all metaslabs in this vdev
- Each metaslab:
- select a metaslab
- load the metaslab
- mark the metaslab as being zeroed
- walk all free ranges within that metaslab and translate
them to ranges on the leaf vdev
- issue a "zeroing" I/O on the leaf vdev that corresponds to
a free range on the metaslab we're working on
- continue until all free ranges for this metaslab have been
"zeroed"
- reset/unmark the metaslab being zeroed
- if more metaslabs exist, then repeat above tasks.
- if no more metaslabs, then we're done.
- progress for the initialization is stored on-disk in the vdev’s
leaf zap object. The following information is stored:
- the last offset that has been initialized
- the state of the initialization process (i.e. active,
suspended, or canceled)
- the start time for the initialization
- progress is reported via the zpool status command and shows
information for each of the vdevs that are initializing
Porting notes:
- Added zfs_initialize_value module parameter to set the pattern
written by "zpool initialize".
- Added zfs_vdev_{initializing,removal}_{min,max}_active module options.
Authored by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Wren Kennedy <john.kennedy@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: loli10K <ezomori.nozomu@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Signed-off-by: Tim Chase <tim@chase2k.com>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/9102
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/c3963210ebCloses#8230
Adds a libzutil for utility functions that are common to libzfs and
libzpool consumers (most of what was in libzfs_import.c). This
removes the need for utilities to link against both libzpool and
libzfs.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#8050
This change moves the bottom half of dmu_send.c (where the receive
logic is kept) into a new file, dmu_recv.c, and does similarly
for receive-related changes in header files.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#7982
This extends our sysfs '/sys/module/zfs' entry to include feature
and property attributes. The primary consumer of this information
is user processes, like the zfs CLI, that need to know what the
current loaded ZFS module supports. The libzfs binary will consult
this information when instantiating the zfs and zpool property
tables and the pool features table.
This introduces 4 kernel objects (dirs) into '/sys/module/zfs'
with corresponding attributes (files):
features.runtime
features.pool
properties.dataset
properties.pool
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#7706
Details about the motivation of this feature and its usage can
be found in this blogpost:
https://sdimitro.github.io/post/zpool-checkpoint/
A lightning talk of this feature can be found here:
https://www.youtube.com/watch?v=fPQA8K40jAM
Implementation details can be found in big block comment of
spa_checkpoint.c
Side-changes that are relevant to this commit but not explained
elsewhere:
* renames members of "struct metaslab trees to be shorter without
losing meaning
* space_map_{alloc,truncate}() accept a block size as a
parameter. The reason is that in the current state all space
maps that we allocate through the DMU use a global tunable
(space_map_blksz) which defauls to 4KB. This is ok for metaslab
space maps in terms of bandwirdth since they are scattered all
over the disk. But for other space maps this default is probably
not what we want. Examples are device removal's vdev_obsolete_sm
or vdev_chedkpoint_sm from this review. Both of these have a
1:1 relationship with each vdev and could benefit from a bigger
block size.
Porting notes:
* The part of dsl_scan_sync() which handles async destroys has
been moved into the new dsl_process_async_destroys() function.
* Remove "VERIFY(!(flags & FWRITE))" in "kernel.c" so zhack can write
to block device backed pools.
* ZTS:
* Fix get_txg() in zpool_sync_001_pos due to "checkpoint_txg".
* Don't use large dd block sizes on /dev/urandom under Linux in
checkpoint_capacity.
* Adopt Delphix-OS's setting of 4 (spa_asize_inflation =
SPA_DVAS_PER_BP + 1) for the checkpoint_capacity test to speed
its attempts to fill the pool
* Create the base and nested pools with sync=disabled to speed up
the "setup" phase.
* Clear labels in test pool between checkpoint tests to avoid
duplicate pool issues.
* The import_rewind_device_replaced test has been marked as "known
to fail" for the reasons listed in its DISCLAIMER.
* New module parameters:
zfs_spa_discard_memory_limit,
zfs_remove_max_bytes_pause (not documented - debugging only)
vdev_max_ms_count (formerly metaslabs_per_vdev)
vdev_min_ms_count
Authored by: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Richard Lowe <richlowe@richlowe.net>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9166
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7159fdb8Closes#7570
In pursuit of improving performance on multi-core systems, we should
implements fanned out counters and use them to improve the performance of
some of the arc statistics. These stats are updated extremely frequently,
and can consume a significant amount of CPU time.
Authored by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: Paul Dagnelie <pcd@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/8484
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/7028a8b92b7
Issue #3752Closes#7462
The timeline of the race condition is the following:
[1] Thread A is about to finish condesing the first vdev in
spa_condense_indirect_thread(), so it calls the
spa_condense_indirect_complete_sync() sync task which sets
the spa_condensing_indirect field to NULL. Waiting for the
sync task to finish, thread A sleeps until the txg is done.
When this happens, thread A will acquire spa_async_lock and
set spa_condense_thread to NULL.
[2] While thread A waits for the txg to finish, thread B which is
running spa_sync() checks whether it should condense the
second vdev in vdev_indirect_should_condense() by checking the
spa_condensing_indirect field which was set to NULL by
spa_condense_indirect_thread() from thread A. So it goes on
and tries to spawn a new condensing thread in
spa_condense_indirect_start_sync() and the aforementioned
assertions fails because thread A has not set spa_condense_thread
to NULL (which is basically the last thing it does before returning).
The main issue here is that we rely on both spa_condensing_indirect
and spa_condense_thread to signify whether a condensing thread is
running. Ideally we would only use one throughout the codebase. In
addition, for managing spa_condense_thread we currently use
spa_async_lock which basically tights condensing to scrubing when
it comes to pausing and resuming those actions during spa export.
This commit introduces the ZTHR infrastructure, which is basically
threads created during spa_load()/spa_create() and exist until we
export or destroy the pool. ZTHRs sleep the majority of the time,
until they are notified to wake up and do some predefined type of work.
In the context of the current bug, a zthr to does the condensing of
indirect mappings replacing the older code that used bare kthreads.
When a pool is created, the condensing zthr is spawned but sleeps
right away, until it is awaken by a signal from spa_sync(). If an
existing pool is loaded, the condensing zthr looks if there is
anything to condense before going to sleep, in case we were condensing
mappings in the pool before it got exported.
The benefits of this solution are the following:
- The current bug is fixed
- spa_condensing_indirect is the sole indicator of whether we are
currently condensing or not
- condensing is more decoupled from the spa_async_thread related
functionality.
As a final note, this commit also sets up the path on upstreaming
other features that use the ZTHR code like zpool checkpoint and
fast clone deletion.
Authored by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Ported-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://illumos.org/issues/9079
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/3dc606eeCloses#6900
OpenZFS 7614 - zfs device evacuation/removal
OpenZFS 9064 - remove_mirror should wait for device removal to complete
This project allows top-level vdevs to be removed from the storage pool
with "zpool remove", reducing the total amount of storage in the pool.
This operation copies all allocated regions of the device to be removed
onto other devices, recording the mapping from old to new location.
After the removal is complete, read and free operations to the removed
(now "indirect") vdev must be remapped and performed at the new location
on disk. The indirect mapping table is kept in memory whenever the pool
is loaded, so there is minimal performance overhead when doing operations
on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become "obsolete" because they are no longer used by any block pointers
in the pool. An entry becomes obsolete when all the blocks that use
it are freed. An entry can also become obsolete when all the snapshots
that reference it are deleted, and the block pointers that reference it
have been "remapped" in all filesystems/zvols (and clones). Whenever an
indirect block is written, all the block pointers in it will be "remapped"
to their new (concrete) locations if possible. This process can be
accelerated by using the "zfs remap" command to proactively rewrite all
indirect blocks that reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of
the data that is copied. This makes the process much faster, but if it
were used on redundant vdevs (i.e. mirror or raidz vdevs), it would be
possible to copy the wrong data, when we have the correct data on e.g.
the other side of the mirror.
At the moment, only mirrors and simple top-level vdevs can be removed
and no removal is allowed if any of the top-level vdevs are raidz.
Porting Notes:
* Avoid zero-sized kmem_alloc() in vdev_compact_children().
The device evacuation code adds a dependency that
vdev_compact_children() be able to properly empty the vdev_child
array by setting it to NULL and zeroing vdev_children. Under Linux,
kmem_alloc() and related functions return a sentinel pointer rather
than NULL for zero-sized allocations.
* Remove comment regarding "mpt" driver where zfs_remove_max_segment
is initialized to SPA_MAXBLOCKSIZE.
Change zfs_condense_indirect_commit_entry_delay_ticks to
zfs_condense_indirect_commit_entry_delay_ms for consistency with
most other tunables in which delays are specified in ms.
* ZTS changes:
Use set_tunable rather than mdb
Use zpool sync as appropriate
Use sync_pool instead of sync
Kill jobs during test_removal_with_operation to allow unmount/export
Don't add non-disk names such as "mirror" or "raidz" to $DISKS
Use $TEST_BASE_DIR instead of /tmp
Increase HZ from 100 to 1000 which is more common on Linux
removal_multiple_indirection.ksh
Reduce iterations in order to not time out on the code
coverage builders.
removal_resume_export:
Functionally, the test case is correct but there exists a race
where the kernel thread hasn't been fully started yet and is
not visible. Wait for up to 1 second for the removal thread
to be started before giving up on it. Also, increase the
amount of data copied in order that the removal not finish
before the export has a chance to fail.
* MMP compatibility, the concept of concrete versus non-concrete devices
has slightly changed the semantics of vdev_writeable(). Update
mmp_random_leaf_impl() accordingly.
* Updated dbuf_remap() to handle the org.zfsonlinux:large_dnode pool
feature which is not supported by OpenZFS.
* Added support for new vdev removal tracepoints.
* Test cases removal_with_zdb and removal_condense_export have been
intentionally disabled. When run manually they pass as intended,
but when running in the automated test environment they produce
unreliable results on the latest Fedora release.
They may work better once the upstream pool import refectoring is
merged into ZoL at which point they will be re-enabled.
Authored by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alex Reece <alex@delphix.com>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Tim Chase <tim@chase2k.com>
OpenZFS-issue: https://www.illumos.org/issues/7614
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/f539f1ebCloses#6900
Authored by: Chris Williamson <chris.williamson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported-by: Don Brady <don.brady@delphix.com>
Ported-by: John Kennedy <john.kennedy@delphix.com>
OpenZFS-issue: https://www.illumos.org/issues/7431
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/dfc11533
Porting Notes:
* The CLI long option arguments for '-t' and '-m' don't parse on linux
* Switched from kmem_alloc to vmem_alloc in zcp_lua_alloc
* Lua implementation is built as its own module (zlua.ko)
* Lua headers consumed directly by zfs code moved to 'include/sys/lua/'
* There is no native setjmp/longjump available in stock Linux kernel.
Brought over implementations from illumos and FreeBSD
* The get_temporary_prop() was adapted due to VFS platform differences
* Use of inline functions in lua parser to reduce stack usage per C call
* Skip some ZFS Test Suite ZCP tests on sparc64 to avoid stack overflow
When --enable-asan is provided to configure then build all user
space components with fsanitize=address. For kernel support
use the Linux KASAN feature instead.
https://github.com/google/sanitizers/wiki/AddressSanitizer
When using gcc version 4.8 any test case which intentionally
generates a core dump will fail when using --enable-asan.
The default behavior is to disable core dumps and only newer
versions allow this behavior to be controled at run time with
the ASAN_OPTIONS environment variable.
Additionally, this patch includes some build system cleanup.
* Rules.am updated to set the minimum AM_CFLAGS, AM_CPPFLAGS,
and AM_LDFLAGS. Any additional flags should be added on a
per-Makefile basic. The --enable-debug and --enable-asan
options apply to all user space binaries and libraries.
* Compiler checks consolidated in always-compiler-options.m4
and renamed for consistency.
* -fstack-check compiler flag was removed, this functionality
is provided by asan when configured with --enable-asan.
* Split DEBUG_CFLAGS in to DEBUG_CFLAGS, DEBUG_CPPFLAGS, and
DEBUG_LDFLAGS.
* Moved default kernel build flags in to module/Makefile.in and
split in to ZFS_MODULE_CFLAGS and ZFS_MODULE_CPPFLAGS. These
flags are set with the standard ccflags-y kbuild mechanism.
* -Wframe-larger-than checks applied only to binaries or
libraries which include source files which are built in
both user space and kernel space. This restriction is
relaxed for user space only utilities.
* -Wno-unused-but-set-variable applied only to libzfs and
libzpool. The remaining warnings are the result of an
ASSERT using a variable when is always declared.
* -D_POSIX_PTHREAD_SEMANTICS and -D__EXTENSIONS__ dropped
because they are Solaris specific and thus not needed.
* Ensure $GDB is defined as gdb by default in zloop.sh.
Signed-off-by: DHE <git@dehacked.net>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#7027
* PBKDF2 implementation changed to OpenSSL implementation.
* HKDF implementation moved to its own file and tests
added to ensure correctness.
* Removed libzfs's now unnecessary dependency on libzpool
and libicp.
* Ztest can now create and test encrypted datasets. This is
currently disabled until issue #6526 is resolved, but
otherwise functions as advertised.
* Several small bug fixes discovered after enabling ztest
to run on encrypted datasets.
* Fixed coverity defects added by the encryption patch.
* Updated man pages for encrypted send / receive behavior.
* Fixed a bug where encrypted datasets could receive
DRR_WRITE_EMBEDDED records.
* Minor code cleanups / consolidation.
Signed-off-by: Tom Caputi <tcaputi@datto.com>
This change incorporates three major pieces:
The first change is a keystore that manages wrapping
and encryption keys for encrypted datasets. These
commands mostly involve manipulating the new
DSL Crypto Key ZAP Objects that live in the MOS. Each
encrypted dataset has its own DSL Crypto Key that is
protected with a user's key. This level of indirection
allows users to change their keys without re-encrypting
their entire datasets. The change implements the new
subcommands "zfs load-key", "zfs unload-key" and
"zfs change-key" which allow the user to manage their
encryption keys and settings. In addition, several new
flags and properties have been added to allow dataset
creation and to make mounting and unmounting more
convenient.
The second piece of this patch provides the ability to
encrypt, decyrpt, and authenticate protected datasets.
Each object set maintains a Merkel tree of Message
Authentication Codes that protect the lower layers,
similarly to how checksums are maintained. This part
impacts the zio layer, which handles the actual
encryption and generation of MACs, as well as the ARC
and DMU, which need to be able to handle encrypted
buffers and protected data.
The last addition is the ability to do raw, encrypted
sends and receives. The idea here is to send raw
encrypted and compressed data and receive it exactly
as is on a backup system. This means that the dataset
on the receiving system is protected using the same
user key that is in use on the sending side. By doing
so, datasets can be efficiently backed up to an
untrusted system without fear of data being
compromised.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Closes#494Closes#5769
OpenZFS provides a library called tpool which implements thread
pools for user space applications. Porting this library means
the zpool utility no longer needs to borrow the kernel mutex and
taskq interfaces from libzpool. This code was updated to use
the tpool library which behaves in a very similar fashion.
Porting libtpool was relatively straight forward and minimal
modifications were needed. The core changes were:
* Fully convert the library to use pthreads.
* Updated signal handling.
* lmalloc/lfree converted to calloc/free
* Implemented portable pthread_attr_clone() function.
Finally, update the build system such that libzpool.so is no
longer linked in to zfs(8), zpool(8), etc. All that is required
is libzfs to which the zcommon soures were added (which is the way
it always should have been). Removing the libzpool dependency
resulted in several build issues which needed to be resolved.
* Moved zfeature support to module/zcommon/zfeature_common.c
* Moved ratelimiting to to module/zfs/zfs_ratelimit.c
* Moved get_system_hostid() to lib/libspl/gethostid.c
* Removed use of cmn_err() in zcommon source
* Removed dprintf_setup() call from zpool_main.c and zfs_main.c
* Removed highbit() and lowbit()
* Removed unnecessary library dependencies from Makefiles
* Removed fletcher-4 kstat in user space
* Added sha2 support explicitly to libzfs
* Added highbit64() and lowbit64() to zpool_util.c
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6442
Add multihost=on|off pool property to control MMP. When enabled
a new thread writes uberblocks to the last slot in each label, at a
set frequency, to indicate to other hosts the pool is actively imported.
These uberblocks are the last synced uberblock with an updated
timestamp. Property defaults to off.
During tryimport, find the "best" uberblock (newest txg and timestamp)
repeatedly, checking for change in the found uberblock. Include the
results of the activity test in the config returned by tryimport.
These results are reported to user in "zpool import".
Allow the user to control the period between MMP writes, and the
duration of the activity test on import, via a new module parameter
zfs_multihost_interval. The period is specified in milliseconds. The
activity test duration is calculated from this value, and from the
mmp_delay in the "best" uberblock found initially.
Add a kstat interface to export statistics about Multiple Modifier
Protection (MMP) updates. Include the last synced txg number, the
timestamp, the delay since the last MMP update, the VDEV GUID, the VDEV
label that received the last MMP update, and the VDEV path. Abbreviated
output below.
$ cat /proc/spl/kstat/zfs/mypool/multihost
31 0 0x01 10 880 105092382393521 105144180101111
txg timestamp mmp_delay vdev_guid vdev_label vdev_path
20468 261337 250274925 68396651780 3 /dev/sda
20468 261339 252023374 6267402363293 1 /dev/sdc
20468 261340 252000858 6698080955233 1 /dev/sdx
20468 261341 251980635 783892869810 2 /dev/sdy
20468 261342 253385953 8923255792467 3 /dev/sdd
20468 261344 253336622 042125143176 0 /dev/sdab
20468 261345 253310522 1200778101278 2 /dev/sde
20468 261346 253286429 0950576198362 2 /dev/sdt
20468 261347 253261545 96209817917 3 /dev/sds
20468 261349 253238188 8555725937673 3 /dev/sdb
Add a new tunable zfs_multihost_history to specify the number of MMP
updates to store history for. By default it is set to zero meaning that
no MMP statistics are stored.
When using ztest to generate activity, for automated tests of the MMP
function, some test functions interfere with the test. For example, the
pool is exported to run zdb and then imported again. Add a new ztest
function, "-M", to alter ztest behavior to prevent this.
Add new tests to verify the new functionality. Tests provided by
Giuseppe Di Natale.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Giuseppe Di Natale <dinatale2@llnl.gov>
Reviewed-by: Ned Bass <bass6@llnl.gov>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#745Closes#6279
This is the Fletcher4 algorithm implemented in pure C, but using
multiple counters using algorithms identical to those used for
SSE/NEON and AVX2.
This allows for faster execution on core with strong superscalar
capabilities but weak SIMD capabilities.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#5317
avx512f should work on all AVX512 hardware, since it only uses
Foundation instructions.
avx512bw should be faster on hardware supporting the AVW512BW
extension. We can use full-width pshufb (instead of relying on the 256
bits AVX2 pshufb). As a side-effect, the code is also unrolled more.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.github@dolbeau.name>
Closes#5219
This is not useful on micro-architecture with a weak NEON
implementation (only 64 bits); the native version is slower &
the byteswap barely faster than scalar. On A53 or A57, it's
a small improvement on scalar but OK for byteswap.
Results from an A53 system:
0 0 0x01 -1 0 1499068294333000 1499101101878000
implementation native byteswap
scalar 1008227510 755880264
aarch64_neon 1198098720 1044818671
fastest aarch64_neon aarch64_neon
Results from a A57 system:
0 0 0x01 -1 0 4407214734807033 4407233933777404
implementation native byteswap
scalar 2302071241 1124873346
aarch64_neon 2542214946 2245570352
fastest aarch64_neon aarch64_neon
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#5248
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Saso Kiselkov <saso.kiselkov@nexenta.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Approved by: Garrett D'Amore <garrett@damore.org>
Ported by: Tony Hutter <hutter2@llnl.gov>
OpenZFS-issue: https://www.illumos.org/issues/4185
OpenZFS-commit: https://github.com/openzfs/openzfs/commit/45818ee
Porting Notes:
This code is ported on top of the Illumos Crypto Framework code:
b5e030c8db
The list of porting changes includes:
- Copied module/icp/include/sha2/sha2.h directly from illumos
- Removed from module/icp/algs/sha2/sha2.c:
#pragma inline(SHA256Init, SHA384Init, SHA512Init)
- Added 'ctx' to lib/libzfs/libzfs_sendrecv.c:zio_checksum_SHA256() since
it now takes in an extra parameter.
- Added CTASSERT() to assert.h from for module/zfs/edonr_zfs.c
- Added skein & edonr to libicp/Makefile.am
- Added sha512.S. It was generated from sha512-x86_64.pl in Illumos.
- Updated ztest.c with new fletcher_4_*() args; used NULL for new CTX argument.
- In icp/algs/edonr/edonr_byteorder.h, Removed the #if defined(__linux) section
to not #include the non-existant endian.h.
- In skein_test.c, renane NULL to 0 in "no test vector" array entries to get
around a compiler warning.
- Fixup test files:
- Rename <sys/varargs.h> -> <varargs.h>, <strings.h> -> <string.h>,
- Remove <note.h> and define NOTE() as NOP.
- Define u_longlong_t
- Rename "#!/usr/bin/ksh" -> "#!/bin/ksh -p"
- Rename NULL to 0 in "no test vector" array entries to get around a
compiler warning.
- Remove "for isa in $($ISAINFO); do" stuff
- Add/update Makefiles
- Add some userspace headers like stdio.h/stdlib.h in places of
sys/types.h.
- EXPORT_SYMBOL *_Init/*_Update/*_Final... routines in ICP modules.
- Update scripts/zfs2zol-patch.sed
- include <sys/sha2.h> in sha2_impl.h
- Add sha2.h to include/sys/Makefile.am
- Add skein and edonr dirs to icp Makefile
- Add new checksums to zpool_get.cfg
- Move checksum switch block from zfs_secpolicy_setprop() to
zfs_check_settable()
- Fix -Wuninitialized error in edonr_byteorder.h on PPC
- Fix stack frame size errors on ARM32
- Don't unroll loops in Skein on 32-bit to save stack space
- Add memory barriers in sha2.c on 32-bit to save stack space
- Add filetest_001_pos.ksh checksum sanity test
- Add option to write psudorandom data in file_write utility
This re-use the framework established for SSE2, SSSE3 and
AVX2. However, GCC is using FP registers on Aarch64, so
unlike SSE/AVX2 we can't rely on the registers being left alone
between ASM statements. So instead, the NEON code uses
C variables and GCC extended ASM syntax. Note that since
the kernel explicitly disable vector registers, they
have to be locally re-enabled explicitly.
As we use the variable's number to define the symbolic
name, and GCC won't allow duplicate symbolic names,
numbers have to be unique. Even when the code is not
going to be used (e.g. the case for 4 registers when
using the macro with only 2). Only the actually used
variables should be declared, otherwise the build
will fails in debug mode.
This requires the replacement of the XOR(X,X) syntax
by a new ZERO(X) macro, which does the same thing but
without repeating the argument. And perhaps someday
there will be a machine where there is a more efficient
way to zero a register than XOR with itself. This affects
scalar, SSE2, SSSE3 and AVX2 as they need the new macro.
It's possible to write faster implementations (different
scheduling, different unrolling, interleaving NEON and
scalar, ...) for various cores, but this one has the
advantage of fitting in the current state of the code,
and thus is likely easier to review/check/merge.
The only difference between aarch64-neon and aarch64-neonx2
is that aarch64-neonx2 unroll some functions some more.
Reviewed-by: Gvozden Neskovic <neskovic@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Romain Dolbeau <romain.dolbeau@atos.net>
Closes#4801
A port of the Illumos Crypto Framework to a Linux kernel module (found
in module/icp). This is needed to do the actual encryption work. We cannot
use the Linux kernel's built in crypto api because it is only exported to
GPL-licensed modules. Having the ICP also means the crypto code can run on
any of the other kernels under OpenZFS. I ended up porting over most of the
internals of the framework, which means that porting over other API calls (if
we need them) should be fairly easy. Specifically, I have ported over the API
functions related to encryption, digests, macs, and crypto templates. The ICP
is able to use assembly-accelerated encryption on amd64 machines and AES-NI
instructions on Intel chips that support it. There are place-holder
directories for similar assembly optimizations for other architectures
(although they have not been written).
Signed-off-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4329
Builds off of 1eeb4562 (Implementation of AVX2 optimized Fletcher-4)
This commit adds another implementation of the Fletcher-4 algorithm.
It is automatically selected at module load if it benchmarks higher
than all other available implementations.
The module benchmark was also amended to analyze the performance of
the byteswap-ed version of Fletcher-4, as well as the non-byteswaped
version. The average performance of the two is used to select the
the fastest implementation available on the host system.
Adds a pair of fields to an existing zcommon module parameter:
- zfs_fletcher_4_impl (str)
"sse2" - new SSE2 implementation if available
"ssse3" - new SSSE3 implementation if available
Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com>
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4789
This is a new implementation of RAIDZ1/2/3 routines using x86_64
scalar, SSE, and AVX2 instruction sets. Included are 3 parity
generation routines (P, PQ, and PQR) and 7 reconstruction routines,
for all RAIDZ level. On module load, a quick benchmark of supported
routines will select the fastest for each operation and they will
be used at runtime. Original implementation is still present and
can be selected via module parameter.
Patch contains:
- specialized gen/rec routines for all RAIDZ levels,
- new scalar raidz implementation (unrolled),
- two x86_64 SIMD implementations (SSE and AVX2 instructions sets),
- fastest routines selected on module load (benchmark).
- cmd/raidz_test - verify and benchmark all implementations
- added raidz_test to the ZFS Test Suite
New zfs module parameters:
- zfs_vdev_raidz_impl (str): selects the implementation to use. On
module load, the parameter will only accept first 3 options, and
the other implementations can be set once module is finished
loading. Possible values for this option are:
"fastest" - use the fastest math available
"original" - use the original raidz code
"scalar" - new scalar impl
"sse" - new SSE impl if available
"avx2" - new AVX2 impl if available
See contents of `/sys/module/zfs/parameters/zfs_vdev_raidz_impl` to
get the list of supported values. If an implementation is not supported
on the system, it will not be shown. Currently selected option is
enclosed in `[]`.
Signed-off-by: Gvozden Neskovic <neskovic@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4328
New functionality:
- Preserves existing scalar implementation.
- Adds AVX2 optimized Fletcher-4 computation.
- Fastest routines selected on module load (benchmark).
- Test case for Fletcher-4 added to ztest.
New zcommon module parameters:
- zfs_fletcher_4_impl (str): selects the implementation to use.
"fastest" - use the fastest version available
"cycle" - cycle trough all available impl for ztest
"scalar" - use the original version
"avx2" - new AVX2 implementation if available
Performance comparison (Intel i7 CPU, 1MB data buffers):
- Scalar: 4216 MB/s
- AVX2: 14499 MB/s
See contents of `/sys/module/zcommon/parameters/zfs_fletcher_4_impl`
to get list of supported values. If an implementation is not supported
on the system, it will not be shown. Currently selected option is
enclosed in `[]`.
Signed-off-by: Jinshan Xiong <jinshan.xiong@intel.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4330
The zfs range lock interface no longer tightly depends on a
znode_t and therefore can be used in ztest. This allows the
previous ztest specific implementation to be removed, and for
additional test coverage of the shared version.
Signed-off-by: Chunwei Chen <david.chen@osnexus.com>
Signed-off-by: Boris Protopopov <boris.protopopov@actifio.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #4023
Issue #4024
In order to remove the HAVE_PN_UTILS wrappers the pn_alloc() and
pn_free() functions must be implemented. The existing illumos
implementation were used for this purpose.
The `flags` argument which was used in places wrapped by the
HAVE_PN_UTILS condition has beed added back to zfs_remove() and
zfs_link() functions. This removes a small point of divergence
between the ZoL code and upstream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#4522
Build products from an out of tree build should be written
relative to the build directory. Sources should be referred
to by their locations in the source directory.
This is accomplished by adding the 'src' and 'obj' variables
for the module Makefile.am, using relative paths to reference
source files, and by setting VPATH when source files are not
co-located with the Makefile. This enables the following:
$ mkdir build
$ cd build
$ ../configure \
--with-spl=$HOME/src/git/spl/ \
--with-spl-obj=$HOME/src/git/spl/build
$ make -s
This change also has the advantage of resolving the following
warning which is generated by modern versions of automake.
Makefile.am:00: warning: source file 'xxx' is in a subdirectory,
Makefile.am:00: but option 'subdir-objects' is disabled
Signed-off-by: Turbo Fredriksson <turbo@bayour.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1082
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Porting notes and other significant code changes:
The illumos 5368 patch (ARC should cache more metadata), which
was never picked up by ZoL, is mostly reverted by this patch.
Since ZoL relies on the kernel asynchronously calling the shrinker to
actually reap memory, the shrinker wakes up arc_reclaim_waiters_cv every
time it runs.
The arc_adapt_thread() function no longer calls arc_do_user_evicts()
since the newly-added arc_user_evicts_thread() calls it periodically.
Notable conflicting ZoL commits which conflicted with this patch or
whose effects are either duplicated or un-done by this patch:
302f753 - Integrate ARC more tightly with Linux
39e055c - Adjust arc_p based on "bytes" in arc_shrink
f521ce1 - Allow "arc_p" to drop to zero or grow to "arc_c"
77765b5 - Remove "arc_meta_used" from arc_adjust calculation
94520ca - Prune metadata from ghost lists in arc_adjust_meta
Trace support for multilist_insert() and multilist_remove() has been
added and produces the following output:
fio-12498 [077] .... 112936.448324: zfs_multilist__insert: ml { offset 240 numsublists 80 sublistidx 63 }
fio-12498 [077] .... 112936.448347: zfs_multilist__remove: ml { offset 240 numsublists 80 sublistidx 29 }
The following arcstats have been removed:
recycle_miss - Used by arcstat.py and arc_summary.py, both of which
have been updated appropriately.
l2_writes_hdr_miss
The following arcstats have been added:
evict_not_enough - Number of times arc_evict_state() was unable to
evict enough buffers to reach its target amount.
evict_l2_skip - Number of times arc_evict_hdr() skipped eviction
because it was being written to the l2arc.
l2_writes_lock_retry - Replaces l2_writes_hdr_miss. Number of times
l2arc_write_done() failed to acquire hash_lock (and re-tries).
arc_meta_min - Shows the value of the zfs_arc_meta_min module
parameter (see below).
The "index" column of the "dbuf" kstat has been removed since it doesn't
have a direct analog in the new multilist scheme. Additional multilist-
related stats could be added in the future but would likely require
extensions to the mulilist API.
The following module parameters have been added:
zfs_arc_evict_batch_limit - Number of ARC headers to free per sub-list
before moving on to the next sub-list.
zfs_arc_meta_min - Enforce a floor on the amount of metadata in
the ARC.
zfs_arc_num_sublists_per_state - Number of multilist sub-lists per
ARC state.
zfs_arc_overflow_shift - Controls amount by which the ARC must exceed
the target size to be considered "overflowing".
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov
This patch leverages Linux tracepoints from within the ZFS on Linux
code base. It also refactors the debug code to bring it back in sync
with Illumos.
The information exported via tracepoints can be used for a variety of
reasons (e.g. debugging, tuning, general exploration/understanding,
etc). It is advantageous to use Linux tracepoints as the mechanism to
export this kind of information (as opposed to something else) for a
number of reasons:
* A number of external tools can make use of our tracepoints
"automatically" (e.g. perf, systemtap)
* Tracepoints are designed to be extremely cheap when disabled
* It's one of the "accepted" ways to export this kind of
information; many other kernel subsystems use tracepoints too.
Unfortunately, though, there are a few caveats as well:
* Linux tracepoints appear to only be available to GPL licensed
modules due to the way certain kernel functions are exported.
Thus, to actually make use of the tracepoints introduced by this
patch, one might have to patch and re-compile the kernel;
exporting the necessary functions to non-GPL modules.
* Prior to upstream kernel version v3.14-rc6-30-g66cc69e, Linux
tracepoints are not available for unsigned kernel modules
(tracepoints will get disabled due to the module's 'F' taint).
Thus, one either has to sign the zfs kernel module prior to
loading it, or use a kernel versioned v3.14-rc6-30-g66cc69e or
newer.
Assuming the above two requirements are satisfied, lets look at an
example of how this patch can be used and what information it exposes
(all commands run as 'root'):
# list all zfs tracepoints available
$ ls /sys/kernel/debug/tracing/events/zfs
enable filter zfs_arc__delete
zfs_arc__evict zfs_arc__hit zfs_arc__miss
zfs_l2arc__evict zfs_l2arc__hit zfs_l2arc__iodone
zfs_l2arc__miss zfs_l2arc__read zfs_l2arc__write
zfs_new_state__mfu zfs_new_state__mru
# enable all zfs tracepoints, clear the tracepoint ring buffer
$ echo 1 > /sys/kernel/debug/tracing/events/zfs/enable
$ echo 0 > /sys/kernel/debug/tracing/trace
# import zpool called 'tank', inspect tracepoint data (each line was
# truncated, they're too long for a commit message otherwise)
$ zpool import tank
$ cat /sys/kernel/debug/tracing/trace | head -n35
# tracer: nop
#
# entries-in-buffer/entries-written: 1219/1219 #P:8
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
lt-zpool-30132 [003] .... 91344.200050: zfs_arc__miss: hdr...
z_rd_int/0-30156 [003] .... 91344.200611: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.201173: zfs_arc__miss: hdr...
z_rd_int/1-30157 [003] .... 91344.201756: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.201795: zfs_arc__miss: hdr...
z_rd_int/2-30158 [003] .... 91344.202099: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202126: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202130: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202134: zfs_arc__hit: hdr ...
lt-zpool-30132 [003] .... 91344.202146: zfs_arc__miss: hdr...
z_rd_int/3-30159 [003] .... 91344.202457: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202484: zfs_arc__miss: hdr...
z_rd_int/4-30160 [003] .... 91344.202866: zfs_new_state__mru...
lt-zpool-30132 [003] .... 91344.202891: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.203034: zfs_arc__miss: hdr...
z_rd_iss/1-30149 [001] .... 91344.203749: zfs_new_state__mru...
lt-zpool-30132 [001] .... 91344.203789: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.203878: zfs_arc__miss: hdr...
z_rd_iss/3-30151 [001] .... 91344.204315: zfs_new_state__mru...
lt-zpool-30132 [001] .... 91344.204332: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204337: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204352: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204356: zfs_arc__hit: hdr ...
lt-zpool-30132 [001] .... 91344.204360: zfs_arc__hit: hdr ...
To highlight the kind of detailed information that is being exported
using this infrastructure, I've taken the first tracepoint line from the
output above and reformatted it such that it fits in 80 columns:
lt-zpool-30132 [003] .... 91344.200050: zfs_arc__miss:
hdr {
dva 0x1:0x40082
birth 15491
cksum0 0x163edbff3a
flags 0x640
datacnt 1
type 1
size 2048
spa 3133524293419867460
state_type 0
access 0
mru_hits 0
mru_ghost_hits 0
mfu_hits 0
mfu_ghost_hits 0
l2_hits 0
refcount 1
} bp {
dva0 0x1:0x40082
dva1 0x1:0x3000e5
dva2 0x1:0x5a006e
cksum 0x163edbff3a:0x75af30b3dd6:0x1499263ff5f2b:0x288bd118815e00
lsize 2048
} zb {
objset 0
object 0
level -1
blkid 0
}
For the specific tracepoint shown here, 'zfs_arc__miss', data is
exported detailing the arc_buf_hdr_t (hdr), blkptr_t (bp), and
zbookmark_t (zb) that caused the ARC miss (down to the exact DVA!).
This kind of precise and detailed information can be extremely valuable
when trying to answer certain kinds of questions.
For anybody unfamiliar but looking to build on this, I found the XFS
source code along with the following three web links to be extremely
helpful:
* http://lwn.net/Articles/379903/
* http://lwn.net/Articles/381064/
* http://lwn.net/Articles/383362/
I should also node the more "boring" aspects of this patch:
* The ZFS_LINUX_COMPILE_IFELSE autoconf macro was modified to
support a sixth paramter. This parameter is used to populate the
contents of the new conftest.h file. If no sixth parameter is
provided, conftest.h will be empty.
* The ZFS_LINUX_TRY_COMPILE_HEADER autoconf macro was introduced.
This macro is nearly identical to the ZFS_LINUX_TRY_COMPILE macro,
except it has support for a fifth option that is then passed as
the sixth parameter to ZFS_LINUX_COMPILE_IFELSE.
These autoconf changes were needed to test the availability of the Linux
tracepoint macros. Due to the odd nature of the Linux tracepoint macro
API, a separate ".h" must be created (the path and filename is used
internally by the kernel's define_trace.h file).
* The HAVE_DECLARE_EVENT_CLASS autoconf macro was introduced. This
is to determine if we can safely enable the Linux tracepoint
functionality. We need to selectively disable the tracepoint code
due to the kernel exporting certain functions as GPL only. Without
this check, the build process will fail at link time.
In addition, the SET_ERROR macro was modified into a tracepoint as well.
To do this, the 'sdt.h' file was moved into the 'include/sys' directory
and now contains a userspace portion and a kernel space portion. The
dprintf and zfs_dbgmsg* interfaces are now implemented as tracepoint as
well.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Ned Bass <bass6@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
4757 ZFS embedded-data block pointers ("zero block compression")
4913 zfs release should not be subject to space checks
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Max Grossman <max.grossman@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Dan McDonald <danmcd@omniti.com>
References:
https://www.illumos.org/issues/4757https://www.illumos.org/issues/4913https://github.com/illumos/illumos-gate/commit/5d7b4d4
Porting notes:
For compatibility with the fastpath code the zio_done() function
needed to be updated. Because embedded-data block pointers do
not require DVAs to be allocated the associated vdevs will not
be marked and therefore should not be unmarked.
Ported by: Tim Chase <tim@chase2k.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2544
4101 metaslab_debug should allow for fine-grained control
4102 space_maps should store more information about themselves
4103 space map object blocksize should be increased
4105 removing a mirrored log device results in a leaked object
4106 asynchronously load metaslab
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Sebastien Roy <seb@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Prior to this patch, space_maps were preferred solely based on the
amount of free space left in each. Unfortunately, this heuristic didn't
contain any information about the make-up of that free space, which
meant we could keep preferring and loading a highly fragmented space map
that wouldn't actually have enough contiguous space to satisfy the
allocation; then unloading that space_map and repeating the process.
This change modifies the space_map's to store additional information
about the contiguous space in the space_map, so that we can use this
information to make a better decision about which space_map to load.
This requires reallocating all space_map objects to increase their
bonus buffer size sizes enough to fit the new metadata.
The above feature can be enabled via a new feature flag introduced by
this change: com.delphix:spacemap_histogram
In addition to the above, this patch allows the space_map block size to
be increase. Currently the block size is set to be 4K in size, which has
certain implications including the following:
* 4K sector devices will not see any compression benefit
* large space_maps require more metadata on-disk
* large space_maps require more time to load (typically random reads)
Now the space_map block size can adjust as needed up to the maximum size
set via the space_map_max_blksz variable.
A bug was fixed which resulted in potentially leaking an object when
removing a mirrored log device. The previous logic for vdev_remove() did
not deal with removing top-level vdevs that are interior vdevs (i.e.
mirror) correctly. The problem would occur when removing a mirrored log
device, and result in the DTL space map object being leaked; because
top-level vdevs don't have DTL space map objects associated with them.
References:
https://www.illumos.org/issues/4101https://www.illumos.org/issues/4102https://www.illumos.org/issues/4103https://www.illumos.org/issues/4105https://www.illumos.org/issues/4106https://github.com/illumos/illumos-gate/commit/0713e23
Porting notes:
A handful of kmem_alloc() calls were converted to kmem_zalloc(). Also,
the KM_PUSHPAGE and TQ_PUSHPAGE flags were used as necessary.
Ported-by: Tim Chase <tim@chase2k.com>
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#2488
Currently there is no mechanism to inspect which dbufs are being
cached by the system. There are some coarse counters in arcstats
by they only give a rough idea of what's being cached. This patch
aims to improve the current situation by adding a new dbufs kstat.
When read this new kstat will walk all cached dbufs linked in to
the dbuf_hash. For each dbuf it will dump detailed information
about the buffer. It will also dump additional information about
the referenced arc buffer and its related dnode. This provides a
more complete view in to exactly what is being cached.
With this generic infrastructure in place utilities can be written
to post-process the data to understand exactly how the caching is
working. For example, the data could be processed to show a list
of all cached dnodes and how much space they're consuming. Or a
similar list could be generated based on dnode type. Many other
ways to interpret the data exist based on what kinds of questions
you're trying to answer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Prakash Surya <surya1@llnl.gov>
This change is an attempt to add visibility into the arc_read calls
occurring on a system, in real time. To do this, a list was added to the
in memory SPA data structure for a pool, with each element on the list
corresponding to a call to arc_read. These entries are then exported
through the kstat interface, which can then be interpreted in userspace.
For each arc_read call, the following information is exported:
* A unique identifier (uint64_t)
* The time the entry was added to the list (hrtime_t)
(*not* wall clock time; relative to the other entries on the list)
* The objset ID (uint64_t)
* The object number (uint64_t)
* The indirection level (uint64_t)
* The block ID (uint64_t)
* The name of the function originating the arc_read call (char[24])
* The arc_flags from the arc_read call (uint32_t)
* The PID of the reading thread (pid_t)
* The command or name of thread originating read (char[16])
From this exported information one can see, in real time, exactly what
is being read, what function is generating the read, and whether or not
the read was found to be already cached.
There is still some work to be done, but this should serve as a good
starting point.
Specifically, dbuf_read's are not accounted for in the currently
exported information. Thus, a follow up patch should probably be added
to export these calls that never call into arc_read (they only hit the
dbuf hash table). In addition, it might be nice to create a utility
similar to "arcstat.py" to digest the exported information and display
it in a more readable format. Or perhaps, log the information and allow
for it to be "replayed" at a later time.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The GNU libtool documentation states to start with a version of 0:0:0,
rather than 1:1:0. Illumos uses the name libzfs_core.so.1, so to be
consistent, we should go with 1:0:0.
http://www.gnu.org/software/libtool/manual/libtool.html#Updating-version-info
The GNU libtool documentation also provides guidence on how the version
information should be incremented. Doing this does a SONAME bump of the
libzfs and libzpool libraries. This is particularly important on Gentoo
because a SONAME bump enables portage to retain the older libraries
until any packages that link to them are rebuilt. The main example of
this is GRUB2's grub2-mkconfig, which will break unless it is rebuilt
against the new libraries.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1751
Libraries that depend on other libraries should list them in ELF's
DT_NEEDED field so that programs linking to them do not need to specify
those libraries unless they depend on them as well. This is not the case
in the current code and the consequence is that anything that needs a
library must know its dependencies. This is fragile and caused GRUB2's
configure script to break when a dependency was added on libblkid in
libzfs.
This resolves that problem by using LIBADD/LDADD to specify libraries in
Makefile.am instead of LDFLAGS. This ensures that proper DT_NEEDED
entries are generated and prevents GRUB2's configure script from
breaking in the presence of a libblkid dependency. This also removes
unneeded dependencies from various files.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #1751
binutils 2.23.1 fails in situations that generate function relocations
on PowerPC and possibly other architectures. This causes linking of
libzpool to fail because it depends on libnvpair. We add a dependency on
libnvpair to lib/libzpool/Makefile.am to correct that.
Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1267
3035 LZ4 compression support in ZFS and GRUB
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Christopher Siden <christopher.siden@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Christopher Siden <csiden@delphix.com>
References:
illumos/illumos-gate@a6f561b4aehttps://www.illumos.org/issues/3035http://wiki.illumos.org/display/illumos/LZ4+Compression+In+ZFS
This patch has been slightly modified from the upstream Illumos
version to be compatible with Linux. Due to the very limited
stack space in the kernel a lz4 workspace kmem cache is used.
Since we are using gcc we are also able to take advantage of the
gcc optimized __builtin_ctz functions.
Support for GRUB has been dropped from this patch. That code
is available but those changes will need to made to the upstream
GRUB package.
Lastly, several hunks of dead code were dropped for clarity. They
include the functions real_LZ4_uncompress(), LZ4_compressBound()
and the Visual Studio specific hunks wrapped in _MSC_VER.
Ported-by: Eric Dillmann <eric@jave.fr>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1217
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>
References:
illumos/illumos-gate@53089ab7c8illumos/illumos-gate@ad135b5d64
illumos changeset: 13700:2889e2596bd6
https://www.illumos.org/issues/2619https://www.illumos.org/issues/2747
NOTE: The grub specific changes were not ported. This change
must be made to the Linux grub packages.
Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
These libraries, which are an artifact of the ZoL development
process, conflict with packages that are already in distribution:
* libspl: SPL Programming Language
* libavl: AVL for Linux
* libefi: GRUB
And these libraries are potential conflicts:
* libshare: the Linux Mount Manager
* libunicode: Perl and Python
Recompose these five ZoL components into the four libraries that are
conventionally provided by Solaris and FreeBSD systems:
+ libnvpair
+ libuutil
+ libzpool
+ libzfs
This change resolves the name conflict, makes ZoL more compatible
with existing software that uses autotools to detect ZFS, and allows
pkg-zfs to better reflect the official Debian kFreeBSD packaging.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #430
The zfs libraries were never properly versioned. Since the API has
remained static for quite some time this we never an issue. However,
going forward they should be versioned. This commit versions all
of the libraries to 1.0.0. From here on out this version must be
updated to reflect changes to the library.
The Linux specific file operations have all been located in the
file zpl_file.c. These functions primarily rely on the reworked
zfs_* functions to do their job. They are also responsible for
converting the possible Solaris style error codes to negative
Linux errors.
This first zpl_* commit also includes a common zpl.h header with
minimal entries to register the Linux specific hooks. In also
adds all the new zpl_* file to the Makefile.in. This is not a
standalone commit, you required the following zpl_* commits.
George Wilson
Don Brady
Paul Dagnelie
Serapheim Dimitropoulos
Paul Dagnelie
Serapheim Dimitropoulos
Matthew Ahrens
Chris Williamson
Brian Behlendorf
Tom Caputi
Olaf Faaland
George Melikov
David Quigley
Romain Dolbeau
Tony Hutter
Gvozden Neskovic
Tyler J. Stachecki
Jinshan Xiong
Boris Protopopov
Turbo Fredriksson
Prakash Surya
Prakash Surya
Richard Yao
Richard Yao
Eric Dillmann
Christopher Siden
Darik Horn
Alejandro R. Sedeño