Do not (incorrectly, right instead left) pad health string itself,
it will be taken care of when printing property value below.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Yuri Pankov <yuripv@FreeBSD.org>
Closes#11899
All users did a freopen() on it. Even some non-users did!
This is point-less ‒ just open the mtab when needed
If I understand Solaris' getextmntent(3C) correctly, the non-user
freopen()s are very likely an odd, twisted vestigial tail of that ‒
but it's got a completely different calling convention and caching
semantics than any platform we support
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11868
Several improvements to the operation of the 'compatibility' property:
1) Improved handling of unrecognized features:
Change the way unrecognized features in compatibility files are handled.
* invalid features in files under /usr/share/zfs/compatibility.d
only get a warning (as these may refer to future features not yet in
the library),
* invalid features in files under /etc/zfs/compatibility.d
get an error (as these are presumed to refer to the current system).
2) Improved error reporting from zpool_load_compat.
Note: slight ABI change to zpool_load_compat for better error reporting.
3) compatibility=legacy inhibits all 'zpool upgrade' operations.
4) Detect when features are enabled outside current compatibility set
* zpool set compatibility=foo <-- print a warning
* zpool set feature@xxx=enabled <-- error
* zpool status <-- indicate this state
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11861
Dunno, maybe it's just me, but the previous style was /really/ confusing
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
It's all of 40 bytes with 4-byte pointers and 64 with 8-byte ones
(previously 44 and 88, respectively) ‒
there's no reason it can't live on the stack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
No users, fields marked "reserved for future use", macros defined to 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
No users, nobody sets it, main() hard-codes LOG_DAEMON, which is the
only correct value for this
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
Users passed in EXIT_SUCCESS and EXIT_FAILURE, despite it being a bool
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11860
A tentative implementation and discussion was done in #5285.
According to it a send --skip-missing|-s flag has been added.
In a replication stream, when there are snapshots missing in
the hierarchy, if -s is provided print a warning and ignore
dataset (and its children) instead of throwing an error
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pablo Correa Gómez <ablocorrea@hotmail.com>
Closes#11710
list_zvols() would happily, for zvols with spaces in their names,
assign the second half to volmode, &c., so use a normal read
and set IFS to a tab instead of using 4 separate AWK processes(?)
Similarly, in filter_out_deleted_zvols(), run zfs(8) once and use the
output directly instead of spawning a zfs(8) process per zvol
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11859
We set SA_RESTART early on, which will prevent EINTRs (indeed, to the
point of needing to clear it in the reaper, since it interferes with
pause(2)), which is the only error zed_file_write_n() actually handled
(plus, the pid write is no bigger than 12 bytes anyway)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
These events should currently never be generated.
Also untag _zed_event_add_nvpair() from merge with
zpool_do_events_nvprint() ‒ they serve different purposes (machine,
usually script vs human consumption) and format the output differently
as it stands
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
Same deal as zed_file_close_on_exec()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
And add a note on /why/ ZEDLETs need to be owned by root
Quoth chown(2), Linux man-pages project:
Only a privileged process (Linux: one with the CAP_CHOWN capability)
may change the owner of a file.
Quoth chown(2), FreeBSD:
[EPERM] The operation would change the ownership,
but the effective user ID is not the super-user.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
There simply isn't a need for one, since the flags the daemon takes
are all short (mostly just toggles) and administrative in nature,
and are therefore better served by the age-old tradition of sourcing an
environment file and preparing the cmdline in the init-specific handler
itself, if needed at all
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
/dev/fd on Darwin
Consider the following strace output:
prlimit64(0, RLIMIT_NOFILE, NULL, {rlim_cur=1024, rlim_max=1024*1024}) = 0
Yes, that is well over a million file descriptors!
This reduces the ZED start-up time from "at least a second" to
"instantaneous", and, under strace, from "don't even try" to "usable"
by simple virtue of doing five syscalls instead of over a million;
in most cases the main loop does nothing
Recent Linuxes (5.8+) have close_range(2) for this, but that's an
overoptimisation (and libcs don't have wrappers for it yet)
This is also run by the ZEDLET pre-exec. Compare:
Finished "all-syslog.sh" eid=13 pid=6717 time=1.027100s exit=0
Finished "history_event-zfs-list-cacher.sh" eid=13 pid=6718 time=1.046923s exit=0
to
Finished "all-syslog.sh" eid=12 pid=4834 time=0.001836s exit=0
Finished "history_event-zfs-list-cacher.sh" eid=12 pid=4835 time=0.001346s exit=0
lol
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11834
zpool list, which is the only user, would mistakenly try to parse the
empty string as the interval in this case:
$ zpool list "a"
cannot open 'a': no such pool
$ zpool list ""
interval cannot be zero
usage: <usage string follows>
which is now symmetric with zpool get:
$ zpool list ""
cannot open '': name must begin with a letter
Avoid breaking the "interval cannot be zero" string.
There simply isn't a need for this, and it's user-facing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11841Closes#11843
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
200ms time-out is relatively long, but if we already hit the cap,
then we'll likely be able to spawn multiple new jobs when we wake up
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11807
The FIXME comment was there since the initial implementation in 2014,
there are no users
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11807
Update the fsck.zfs helper to bubble up some already-known-about
errors if they are detected in the pool.
health=degraded => 4/"Filesystem errors left uncorrected"
health=faulted && dataset in /etc/fstab => 8/"Operational error"
pool not found => 8/"Operational error"
everything else => 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11806
ZoL 0.6.1 introduced feature flags with the three features that all
implementations at the time were guaranteed to have. 0.6.4 introduced
a few more until 0.6.5 added two after that. OpenZFS 2.1 added the
dRAID feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mike Swanson <mikeonthecomputer@gmail.com>
Closes#11818
When a child process is killed waitpid() must be called on the
pid the reap the zombie process.
Update BUGS section to reflect reality by replacing "zedlets
aren't time limited with "zedlets can be interrupted".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11769Closes#11798
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11775
If TX_WRITE is create on a file, and the file is later deleted and a new
directory is created on the same object id, it is possible that when
zil_commit happens, zfs_get_data will be called on the new directory.
This may result in panic as it tries to do range lock.
This patch fixes this issue by record the generation number during
zfs_log_write, so zfs_get_data can check if the object is valid.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#10593Closes#11682
The RAIDZ and DRAID code is responsible for reporting checksum errors on
their child vdevs. Checksum errors represent events where a disk
returned data or parity that should have been correct, but was not. In
other words, these are instances of silent data corruption. The
checksum errors show up in the vdev stats (and thus `zpool status`'s
CKSUM column), and in the event log (`zpool events`).
Note, this is in contrast with the more common "noisy" errors where a
disk goes offline, in which case ZFS knows that the disk is bad and
doesn't try to read it, or the device returns an error on the requested
read or write operation.
RAIDZ/DRAID generate checksum errors via three code paths:
1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are
reported on any children whose data was not used during the
reconstruction. This is handled in `raidz_reconstruct()`. This is the
most common type of RAIDZ/DRAID checksum error.
2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that
means that the data has been lost. The zio fails and an error is
returned to the consumer (e.g. the read(2) system call). This would
happen if, for example, three different disks in a RAIDZ2 group are
silently damaged. Since the damage is silent, it isn't possible to know
which three disks are damaged, so a checksum error is reported against
every child that returned data or parity for this read. (For DRAID,
typically only one "group" of children is involved in each io.) This
case is handled in `vdev_raidz_cksum_finish()`. This is the next most
common type of RAIDZ/DRAID checksum error.
3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in
case 2), but there happens to be additional copies of this block due to
"ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those
copies is good, then RAIDZ/DRAID compares each sector of the data or
parity that it retrieved with the good data from the other DVA, and if
they differ then it reports a checksum error on this child. This
differs from case 2 in that the checksum error is reported on only the
subset of children that actually have bad data or parity. This case
happens very rarely, since normally only metadata has ditto blocks. If
the silent damage is extensive, there will be many instances of case 2,
and the pool will likely be unrecoverable.
The code for handling case 3 is considerably more complicated than the
other cases, for two reasons:
1. It needs to run after the main raidz read logic has completed. The
data RAIDZ read needs to be preserved until after the alternate DVA has
been read, which necessitates refcounts and callbacks managed by the
non-raidz-specific zio layer.
2. It's nontrivial to map the sections of data read by RAIDZ to the
correct data. For example, the correct data does not include the parity
information, so the parity must be recalculated based on the correct
data, and then compared to the parity that was read from the RAIDZ
children.
Due to the complexity of case 3, the rareness of hitting it, and the
minimal benefit it provides above case 2, this commit removes the code
for case 3. These types of errors will now be handled the same as case
2, i.e. the checksum error will be reported against all children that
returned data or parity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11735
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
vdev_id uses the /dev/mapper/ symlinks to resolve a UUID to a dm name
(like dm-1). However on some multipath setups, there is no /dev/mapper/
entry for the UUID at the time vdev_id is called by udev. However,
this isn't necessarily needed, as we may be able to resolve the dm
name from the $DEVNAME that udev passes us (like DEVNAME="/dev/dm-1").
This patch tries to resolve the dm name from $DEVNAME first, before
falling back to looking in /dev/mapper/. This fixed an issue where the
by-vdev names weren't reliably showing up on one of our nodes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11698
For some reason cppcheck 1.90 is generating an invalidSyntax warning
when the BF64_SET macro is used in the zstream source. The same
warning is not reported by cppcheck 2.3, nor is their any evident
problem with the expanded macro. This appears to be an issue with
this version of cppcheck. This commit annotates the source to suppress
the warning.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11700
Bring the output of the removal status in line with the other
"fields" that zpool status outputs, and thus allows an parser to
easier detect this as continuation of the 'remove:' output.
Before:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Now:
remove: Removal of vdev 0 copied 282G in 0h9m, completed on [...]
776K memory used for removed device mappings
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Closes#11674
After 35ec517 it has become possible to import ZFS pools witn an
active org.illumos:edonr feature on FreeBSD, leading to a panic.
In addition, "zpool status" reported all pools without edonr
as upgradable and "zpool upgrade -v" reported edonr in the list
of upgradable features.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11653
Given a DM device name, the old vdev_id script would extract any text
after a 'p' as the partition number. It then appends "-part" + the
partition number to the name, giving a by-vdev name like "L0-part5".
This works fine if the DM name is like 'dm-2p5', but doesn't work if
the DM name is a multipath name like "mpatha". In those cases it
incorrectly matches the 'p' in "mpatha", giving by-vdev names like
"L0-partatha".
This patch fixes the issue by making the partition regex match stricter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11637
gmake install fails when zpool.d compat links already exist.
Force the symlinks to be recreated if already present.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11633
I think this is the behavior that most users expect.
Future work: have a separate flag, e.g., -O, to specify separate
set_global_vars for the zdb child than for the ztest children.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11602
Without set_global_var() in the child processes the -o option provides
little use.
Before this change set_global_var() was called as a side-effect of
getopt processing which only happens for the parent ztest process.
This change limits the set of options that can be set and makes them
available to the child through ztest_shared_opts_t.
Future work: support arbitrary option count and length.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11602
That happens because of an off-by-one mistake.
share_mount_one_cb() calls report_mount_progress(current=sm_done) after
having incremented sm_done by one. Then report_mount_progress()
increments the parameter again. It appears that that logic became
obsolete after commit a10d50f999, parallel zfs mount.
On FreeBSD I observe that zfs mount -a -v prints, for example,
(null): (201/248)
That happens because set_progress_header() is never called.
With this change the output becomes correct:
Mounting ZFS filesystems: (209/248)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11607
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
Rather than conditionally compiling out the edonr code for FreeBSD
update zfs_mod_supported_feature() to indicate this feature is
unsupported. This ensures that all spa features are defined on
every platform, even if they are not supported.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11605
Issue #11468
Yuri Pankov
наб
Colm
pablofsf
Andrea Gelmini
Mike Swanson
Chunwei Chen
Matthew Ahrens
George Wilson
Tony Hutter
Brian Behlendorf
Thomas Lamprecht
Martin Matuška
Ryan Moeller
Christian Schwarz
Andriy Gapon