Update the fsck.zfs helper to bubble up some already-known-about
errors if they are detected in the pool.
health=degraded => 4/"Filesystem errors left uncorrected"
health=faulted && dataset in /etc/fstab => 8/"Operational error"
pool not found => 8/"Operational error"
everything else => 0
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11806
ZoL 0.6.1 introduced feature flags with the three features that all
implementations at the time were guaranteed to have. 0.6.4 introduced
a few more until 0.6.5 added two after that. OpenZFS 2.1 added the
dRAID feature.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mike Swanson <mikeonthecomputer@gmail.com>
Closes#11818
Increase the version to 2.1.99 to indicate the master branch is
newer than the 2.1.x release. This ensures packages built from
master branch are considered to be newer than the last release.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When a child process is killed waitpid() must be called on the
pid the reap the zombie process.
Update BUGS section to reflect reality by replacing "zedlets
aren't time limited with "zedlets can be interrupted".
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11769Closes#11798
For gang blocks, `DVA_GET_ASIZE()` is the total space allocated for the
gang DVA including its children BP's. The space allocated at each DVA's
vdev/offset is `vdev_psize_to_asize(vd, SPA_GANGBLOCKSIZE)`.
This commit makes this relationship more clear by using a helper
function, `vdev_gang_header_asize()`, for the space allocated at the
gang block's vdev/offset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11744
When specifying the name of a RAIDZ vdev on the command line, it can be
specified as raidz-<vdevID> or raidzP-<vdevID>.
e.g. `zpool clear poolname raidz-0` or `zpool clear poolname raidz2-0`
If the parity is specified in the vdev name, it should match the actual
parity of that RAIDZ vdev, otherwise the command should fail. This
commit makes it so.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Stuart Maybee <stuart.maybee@comcast.net>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11742
Other (all?) Linux filesystems seem to return -EPERM instead of -EACCESS
when trying to set FS_APPEND_FL or FS_IMMUTABLE_FL without the
CAP_LINUX_IMMUTABLE capability. This was detected by generic/545 test
in the fstest suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luis Henriques <henrix@camandro.org>
Closes#11791
Arm-based Macs are like FreeBSD and provide a full 64-bit stat from the
start, so have no stat64 variants. Thus, define stat64 and fstat64 as
aliases for the normal versions.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Closes#11771
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11775
To make better predictions on parallel workloads dmu_zfetch() should
be called as early as possible to reduce possible request reordering.
In particular, it should be called before dmu_buf_hold_array_by_dnode()
calls dbuf_hold(), which may sleep waiting for indirect blocks, waking
up multiple threads same time on completion, that can significantly
reorder the requests, making the stream look like random. But we
should not issue prefetch requests before the on-demand ones, since
they may get to the disks first despite the I/O scheduler, increasing
on-demand request latency.
This patch splits dmu_zfetch() into two functions: dmu_zfetch_prepare()
and dmu_zfetch_run(). The first can be executed as early as needed.
It only updates statistics and makes predictions without issuing any
I/Os. The I/O issuance is handled by dmu_zfetch_run(), which can be
called later when all on-demand I/Os are already issued. It even
tracks the activity of other concurrent threads, issuing the prefetch
only when _all_ on-demand requests are issued.
For many years it was a big problem for storage servers, handling
deeper request queues from their clients, having to either serialize
consequential reads to make ZFS prefetcher usable, or execute the
incoming requests as-is and get almost no prefetch from ZFS, relying
only on deep enough prefetch by the clients. Benefits of those ways
varied, but neither was perfect. With this patch deeper queue
sequential read benchmarks with CrystalDiskMark from Windows via
iSCSI to FreeBSD target show me much better throughput with almost
100% prefetcher hit rate, comparing to almost zero before.
While there, I also removed per-stream zs_lock as useless, completely
covered by parent zf_lock. Also I reused zs_blocks refcount to track
zf_stream linkage of the stream, since I believe previous zs_fetch ==
NULL check in dmu_zfetch_stream_done() was racy.
Delete prefetch streams when they reach ends of files. It saves up
to 1KB of RAM per file, plus reduces searches through the stream list.
Block data prefetch (speculation and indirect block prefetch is still
done since they are cheaper) if all dbufs of the stream are already
in DMU cache. First cache miss immediately fires all the prefetch
that would be done for the stream by that time. It saves some CPU
time if same files within DMU cache capacity are read over and over.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11652
If TX_WRITE is create on a file, and the file is later deleted and a new
directory is created on the same object id, it is possible that when
zil_commit happens, zfs_get_data will be called on the new directory.
This may result in panic as it tries to do range lock.
This patch fixes this issue by record the generation number during
zfs_log_write, so zfs_get_data can check if the object is valid.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#10593Closes#11682
Commit 235a85657 introduced a regression in evaluation of POSIX modes
that require group DENY entries in the internal ZFS ACL. An example
of such a POSX mode is 007. When write_implies_delete_child is set,
then ACE_WRITE_DATA is added to `wanted_dirperms` in prior to calling
zfs_zaccess_common(). This occurs is zfs_zaccess_delete().
Unfortunately, when zfs_zaccess_aces_check hits this particular DENY
ACE, zfs_groupmember() is checked to determine whether access should be
denied, and since zfs_groupmember() always returns B_TRUE on Linux and
so this check is failed, resulting ultimately in EPERM being returned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#11760
This change adds a new test that covers a bug fix in the binary search
in the redacted send resume logic that causes a kernel panic.
The bug was fixed in https://github.com/openzfs/zfs/pull/11297.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Palash Gandhi <palash.gandhi@delphix.com>
Closes#11764
The FreeBSD boot loader relies on the bootfs property and is capable
of booting from removed (indirect) vdevs.
Reviewed-by Eric van Gyzen
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11763
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11770
It used to be required to pass a enum km_type to kmap_atomic() and
kunmap_atomic(), however this is no longer necessary and the wrappers
zfs_k(un)map_atomic removed these. This is confusing in the ABD code as
the struct abd_iter member iter_km no longer exists and the wrapper
macros simply compile them out.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11768
= Motivation
We've noticed several zloop crashes within Delphix generated
due to the following sequence of events:
- A device gets expanded and new metaslabas are allocated for
it. These metaslabs go through `metaslab_init()` but haven't
gone through `metaslab_sync_done()` yet. This meas that the
only range tree that's actually set is the `ms_allocatable`.
All the others are NULL.
- A vdev_initialization is issues and `vdev_initialize_thread`
starts processing one of these new metaslabs of the expanded
vdev.
- As part of `vdev_initialize_calculate_progress()` we call
into `metaslab_load()` and `metaslab_load_impl()` which
in turn tries to dereference the metaslabs trees that
are still NULL and therefore we crash.
The same failure can come up from the `vdev_trim` code paths.
= This Patch
We considered the following solutions to deal with this issue:
[A] Add logic to `vdev_initialize/trim` to skip those new
metaslabs. We decided against this as it would be good
to avoid exposing this lower-level detail to higer-level
operations.
[B] Have `metaslab_load_impl()` return early for new metaslabs
and thus never touch those range_trees that are NULL at
that time. This seemed more of a work-around for the bug
and not a clear-cut solution.
[C] Refactor our logic so all metaslabs have their range_trees
created at the time of their creatin in `metaslab_init()`.
In this patch we decided to go with [C] because:
(1) It doesn't expose more metaslab details to higher level
operations such as vdev initialize and trim.
(2) The current behavior of creating the range trees lazily
in `metaslab_sync_done()` is unnecessarily complicated.
(3) Always initializing the metaslab range_trees makes other
parts of the codebase cleaner. For example, we used to
use `ms_freed` as the reference value for knowing whether
all the range_trees have been initialized. Now we no
longer need to do that check in most places (and in the
few that we do we use the `ms_new` boolean field now
which is more readable).
= Side Changes
Probably due to a mismerge we set `ms_loaded` to `B_TRUE` twice
in `metasloab_load_impl()`. In this patch we remove the extraneous
assignment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11737
The BIO_MAX_PAGES macro is being retired in favor of a bio_max_segs()
function that implements the typical MIN(x,y) logic used throughout the
kernel for bounding the allocation, and also the new implementation is
intended to be signed-safe (which the former was not).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11765
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
The RAIDZ and DRAID code is responsible for reporting checksum errors on
their child vdevs. Checksum errors represent events where a disk
returned data or parity that should have been correct, but was not. In
other words, these are instances of silent data corruption. The
checksum errors show up in the vdev stats (and thus `zpool status`'s
CKSUM column), and in the event log (`zpool events`).
Note, this is in contrast with the more common "noisy" errors where a
disk goes offline, in which case ZFS knows that the disk is bad and
doesn't try to read it, or the device returns an error on the requested
read or write operation.
RAIDZ/DRAID generate checksum errors via three code paths:
1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are
reported on any children whose data was not used during the
reconstruction. This is handled in `raidz_reconstruct()`. This is the
most common type of RAIDZ/DRAID checksum error.
2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that
means that the data has been lost. The zio fails and an error is
returned to the consumer (e.g. the read(2) system call). This would
happen if, for example, three different disks in a RAIDZ2 group are
silently damaged. Since the damage is silent, it isn't possible to know
which three disks are damaged, so a checksum error is reported against
every child that returned data or parity for this read. (For DRAID,
typically only one "group" of children is involved in each io.) This
case is handled in `vdev_raidz_cksum_finish()`. This is the next most
common type of RAIDZ/DRAID checksum error.
3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in
case 2), but there happens to be additional copies of this block due to
"ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those
copies is good, then RAIDZ/DRAID compares each sector of the data or
parity that it retrieved with the good data from the other DVA, and if
they differ then it reports a checksum error on this child. This
differs from case 2 in that the checksum error is reported on only the
subset of children that actually have bad data or parity. This case
happens very rarely, since normally only metadata has ditto blocks. If
the silent damage is extensive, there will be many instances of case 2,
and the pool will likely be unrecoverable.
The code for handling case 3 is considerably more complicated than the
other cases, for two reasons:
1. It needs to run after the main raidz read logic has completed. The
data RAIDZ read needs to be preserved until after the alternate DVA has
been read, which necessitates refcounts and callbacks managed by the
non-raidz-specific zio layer.
2. It's nontrivial to map the sections of data read by RAIDZ to the
correct data. For example, the correct data does not include the parity
information, so the parity must be recalculated based on the correct
data, and then compared to the parity that was read from the RAIDZ
children.
Due to the complexity of case 3, the rareness of hitting it, and the
minimal benefit it provides above case 2, this commit removes the code
for case 3. These types of errors will now be handled the same as case
2, i.e. the checksum error will be reported against all children that
returned data or parity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11735
Avoids tripping on asserts when doing pool recovery.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11739
The `rr_code` field in `raidz_row_t` is unused.
This commit removes the field, as well as the code that's used to set
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11736
Don't handle (incorrectly) kmem_zalloc() failure. With KM_SLEEP,
will never return NULL.
Free the data allocated for non-virtual kstats when deleting the object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11767
zhold() wraps igrab() on Linux, and igrab() may fail when the inode
is in the process of being deleted. This means zhold() must only be
called when a reference exists and therefore it cannot be deleted.
This is the case for all existing consumers so add a VERIFY and a
comment explaining this requirement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11704
The man page was missing these two permissions.
Add the missing permissions to the man page.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jeremy Faulkner <gldisater@gldis.ca>
Closes#11727
Create a new section of tests to run with acltype=off.
For now the only test we have is for the DOS mode READONLY attribute on
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11734
To make use of zfs_refcount_held tunable it should be a module
parameter in open-zfs. Also, since the macros will auto-generate OS
specific tunables, removed the existing zfs_refcount_held reference
in module/os/freebsd/zfs/sysctl_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11753
You can't use user_run to eval ksh functions defined in libtest unless
you include libtest in the user shell.
Fix xattr_003_neg by:
* include libtest in the user shell
* *then* run get_xattr
* assert this fails
* use variables for filenames so they don't change in the user's shell
* don't log the contents of /etc/passwd
* cleanup all byproducts
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
The current user_run often does not work as expected. Commands are run
in a different shell, with a different environment, and all output is
discarded.
Simplify user_run to retain the current environment, eliminate eval,
and feed the command string into ksh. Enhance the logging for
user_run so we can see out and err.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11185
Add parsing of the rewind options.
When I was upstreaming the change [1], I omitted the part where we
detect that the pool should be rewind. When the FreeBSD repo has
synced with the OpenZFS, this part of the code was removed.
[1] FreeBSD repo: 277f38abffc6a8160b5044128b5b2c620fbb970c
[2] OpenZFS repo: f2c027bd6a
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=254152
Originally reviewed by: tsoome, allanjude
Originally reviewed by: kevans (ok from high-level overview)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11730
Resolve some oddities in zfsdev_close() which could result in a
panic and were not present in the equivalent function for Linux.
- Remove unused definition ZFS_MIN_MINOR
- FreeBSD: Simplify zfsdev state destruction
- Assert zs_minor is valid in zfsdev_close
- Make locking around zfsdev state match Linux
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11720
This deserializes otherwise non-contending operations.
The previous scheme of using 17 locks hashed by curthread runs into
conflicts very quickly. Check the pull request for sample results.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
This will allow platforms to implement it as they see fit, in particular
in a different manner than rrm locks.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are not very useful and hard to implement in the rms routine
the code is about to start using.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
1. even up ifdefs
2. drop the arguably useless teardown lock asserts -- nothing else
checks for it
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are expected to fail only in corner cases.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
The manual page change in ecc277c has introduced whitespace on
line ends.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11722
A few deadman tunables ended up in the wrong sysctl node.
Move them to vfs.zfs.deadman.*
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11715
Add branch hints and constify the intermediate evaluations of
left/right params in VERIFY3*().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11708
Some .h files that were added were missed in this Makefile. Since
they are .h files, their being missing only resulted in them
disappeared from the dist archive.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11705
Our checkstyle doesn't work well on Ubuntu 20.04,
temporary pin it to 18.04.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11713
Added errno mappings to unmount_one() in libzfs. Changed do_unmount()
implementation to return errno errors directly like is done for
do_mount() and others.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11681
vdev_id uses the /dev/mapper/ symlinks to resolve a UUID to a dm name
(like dm-1). However on some multipath setups, there is no /dev/mapper/
entry for the UUID at the time vdev_id is called by udev. However,
this isn't necessarily needed, as we may be able to resolve the dm
name from the $DEVNAME that udev passes us (like DEVNAME="/dev/dm-1").
This patch tries to resolve the dm name from $DEVNAME first, before
falling back to looking in /dev/mapper/. This fixed an issue where the
by-vdev names weren't reliably showing up on one of our nodes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11698
events_002 exercises the ZED, ensuring that it neither misses events,
nor reporting events twice.
On slow test hardware, some of the timeouts are insufficient to allow
the ZED to properly settle. Conversely, on fast hardware these same
timeouts are too long, unnecessarily slowing the test run.
Instead of using a fixed timeout, wait for the expected final event
before returning. Additionally, wait with a timeout for unexpected
events to avoid missing them if they show up late.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11703
zil_replaying(zil, tx) has the side-effect of informing the ZIL that an
entry has been replayed in the (still open) tx. The ZIL uses that
information to record the replay progress in the ZIL header when that
tx's txg syncs.
ZPL log entries are not idempotent and logically dependent and thus
calling zil_replaying() is necessary for correctness.
For ZVOLs the question of correctness is more nuanced: ZVOL logs only
TX_WRITE and TX_TRUNCATE, both of which are idempotent. Logical
dependencies between two records exist only if the write or discard
request had sync semantics or if the ranges affected by the records
overlap.
Thus, at a first glance, it would be correct to restart replay from
the beginning if we crash before replay completes. But this does not
address the following scenario:
Assume one log record per LWB.
The chain on disk is
HDR -> 1:W(1, "A") -> 2:W(1, "B") -> 3:W(2, "X") -> 4:W(3, "Z")
where N:W(O, C) represents log entry number N which is a TX_WRITE of C
to offset A.
We replay 1, 2 and 3 in one txg, sync that txg, then crash.
Bit flips corrupt 2, 3, and 4.
We come up again and restart replay from the beginning because
we did not call zil_replaying() during replay.
We replay 1 again, then interpret 2's invalid checksum as the end
of the ZIL chain and call replay done.
The replayed zvol content is "AX".
If we had called zil_replaying() the HDR would have pointed to 3
and our resumed replay would not have replayed anything because
3 was corrupted, resulting in zvol content "BX".
If 3 logically depends on 2 then the replay corrupted the ZVOL_OBJ's
contents.
This patch adds the zil_replaying() calls to the replay functions.
Since the callbacks in the replay function need the zilog_t* pointer
so that they can call zil_replaying() we open the ZIL while
replaying in zvol_create_minor(). We also verify that replay has
been done when on-demand-opening the ZIL on the first modifying
bio.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11667
наб
Mike Swanson
Brian Behlendorf
Matthew Ahrens
Luis Henriques
Jessica Clarke
Andrea Gelmini
Alexander Motin
Chunwei Chen
Andrew
Palash Gandhi
Martin Matuška
Ryan Moeller
Brian Atkinson
Serapheim Dimitropoulos
Coleman Kane
Mateusz Guzik
Adam D. Moss
Dries Michiels
gldisater
Don Brady
Mariusz Zaborski
George Wilson
Allan Jude
George Melikov
Tony Hutter
Antonio Russo
Christian Schwarz