Under certain conditions commit a3a4b8def appears to result in a
hang, or poor performance, when importing a pool. Until the root
cause can be identified it has been reverted from the release branch.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11245
Investigating influence of scrub (especially sequential) on random read
latency I've noticed that on some HDDs single 4KB read may take up to 4
seconds! Deeper investigation shown that many HDDs heavily prioritize
sequential reads even when those are submitted with queue depth of 1.
This patch addresses the latency from two sides:
- by using _min_active queue depths for non-interactive requests while
the interactive request(s) are active and few requests after;
- by throttling it further if no interactive requests has completed
while configured amount of non-interactive did.
While there, I've also modified vdev_queue_class_to_issue() to give
more chances to schedule at least _min_active requests to the lowest
priorities. It should reduce starvation if several non-interactive
processes are running same time with some interactive and I think should
make possible setting of zfs_vdev_max_active to as low as 1.
I've benchmarked this change with 4KB random reads from ZVOL with 16KB
block size on newly written non-fragmented pool. On fragmented pool I
also saw improvements, but not so dramatic. Below are log2 histograms
of the random read latency in milliseconds for different devices:
4 2x mirror vdevs of SATA HDD WDC WD20EFRX-68EUZN0 before:
0, 0, 2, 1, 12, 21, 19, 18, 10, 15, 17, 21
after:
0, 0, 0, 24, 101, 195, 419, 250, 47, 4, 0, 0
, that means maximum latency reduction from 2s to 500ms.
4 2x mirror vdevs of SATA HDD WDC WD80EFZX-68UW8N0 before:
0, 0, 2, 31, 38, 28, 18, 12, 17, 20, 24, 10, 3
after:
0, 0, 55, 247, 455, 470, 412, 181, 36, 0, 0, 0, 0
, i.e. from 4s to 250ms.
1 SAS HDD SEAGATE ST14000NM0048 before:
0, 0, 29, 70, 107, 45, 27, 1, 0, 0, 1, 4, 19
after:
1, 29, 681, 1261, 676, 1633, 67, 1, 0, 0, 0, 0, 0
, i.e. from 4s to 125ms.
1 SAS SSD SEAGATE XS3840TE70014 before (microseconds):
0, 0, 0, 0, 0, 0, 0, 0, 70, 18343, 82548, 618
after:
0, 0, 0, 0, 0, 0, 0, 0, 283, 92351, 34844, 90
I've also measured scrub time during the test and on idle pools. On
idle fragmented pool I've measured scrub getting few percent faster
due to use of QD3 instead of QD2 before. On idle non-fragmented pool
I've measured no difference. On busy non-fragmented pool I've measured
scrub time increase about 1.5-1.7x, while IOPS increase reached 5-9x.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11166
- Don't leave fstrans set when passed a snapshot
- Don't remove minor if volmode already matches new value
- (FreeBSD) Wait for GEOM ops to complete before trying
remove (at create time GEOM will be "tasting" in parallel)
- (FreeBSD) Don't leak zvol_state_lock on open if zv == NULL
- (FreeBSD) Don't try to unlock zv->zv_state lock if zv == NULL
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11199
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
The output of ZFS channel programs is logged on-disk in the zpool
history, and printed by `zpool history -i`. Channel programs can use
10MB of memory by default, and up to 100MB by using the `zfs program -m`
flag. Therefore their output can be up to some fraction of 100MB.
In addition to being somewhat wasteful of the limited space reserved for
the pool history (which for large pools is 1GB), in extreme cases this
can result in a failure of `ASSERT(length <= DMU_MAX_ACCESS);` in
`dmu_buf_hold_array_by_dnode()`.
This commit limits the output size that will be logged to 1MB. Larger
outputs will not be logged, instead a entry will be logged indicating
the size of the omitted output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11194
The field is yet another leftover from unsupported zfs_znode_move.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11186
In Linux 5.10 the linux/frame.h header was renamed linux/objtool.h.
Add a configure check to detect and use the correctly named header.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11085
Note that this only tracks sizes as requested by the caller.
Actual allocated space will almost always be bigger (e.g., rounded up to
the next power of 2 or page size). Additionally the allocated buffer may
be holding other areas hostage. Nonetheless, this is a starting point
for tracking memory usage in zstd.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11129
Refer to the correct section or alternative for FreeBSD and Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11132
The acltype property is currently hidden on FreeBSD and does not
reflect the NFSv4 style ZFS ACLs used on the platform. This makes it
difficult to observe that a pool imported from FreeBSD on Linux has a
different type of ACL that is being ignored, and vice versa.
Add an nfsv4 acltype and expose the property on FreeBSD.
Make the default acltype nfsv4 on FreeBSD.
Setting acltype to an unhanded style is treated the same as setting
it to off. The ACLs will not be removed, but they will be ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10520
In FreeBSD, there are three compile environments that are supported:
user land, the kernel and the bootloader / standalone. Adjust the
headers to compile in the standalone environment. Limit kernel-only
items from view when _STANDALONE is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Warner Losh <imp@FreeBSD.org>
Closes#10998
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11047
Code cleanup, a follow up commit to 4d55ea81.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@freqlabs.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11020
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
In non regular use cases allocated memory might stay persistent in memory
pool. This small patch checks every minute if there are old objects which
can be released from memory pool.
Right now with regular use, the pool is checked for old objects on each
allocation attempt from this pool. so basically polling by its use. Now
consider what happens if someone writes a lot of files and stops use of
the volume or even unmounts it. So the code will no longer check if
objects can be released from the pool. Already allocated objects will
still stay in pool cache. this is no big issue for common use. But
someone discovered this issue while doing tests. personally i know this
behavior and I'm aware of it. Its no big issue. just a enhancement
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#10938Closes#10969
The m4 objtool configure check can incorrectly fail because of a
missing header in the test. This appears to be the result of a
recent kernel change and was observed on the Fedora 5.8.11-200
kernel.
In file included from /home/fedora/zfs/build/objtool/objtool.c:75:
./arch/x86/include/asm/frame.h💯57: error: 'struct pt_regs'
declared inside parameter list will not be visible outside
of this definition or declaration [-Werror]
The consequence of this is that the "stack_frame_non_standard"
check is never run and HAVE_STACK_FRAME_NON_STANDARD is set
incorrectly which results in a build failure. This change adds
the appropriate header to the "objtool" check so it now behaves
as intended.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10990
The procfs_list interface is required by several kstats. Implement
this functionality for FreeBSD to provide access to these kstats.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10890
Use the same reduced buffer size for lauxlib that is used on Linux.
Fixes panic on HEAD in lua gsub test designed to exhaust stack space.
With this we can remove the special case to reserve more stack space
on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10959
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
Prefer acltype=off|posix, retaining the old names as aliases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10918
nvlist does allow us to support different data types and systems.
To encapsulate user data to/from nvlist, the libzfsbootenv library is
provided.
Reviewed-by: Arvind Sankar <nivedita@alum.mit.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10774
When hz > 1000, msec / (1000 / hz) results in division by zero.
I found somewhere in FreeBSD using howmany(msec * hz, 1000) to convert
ms to ticks, avoiding the potential for a zero in the divisor.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10894
Duplicate io and checksum ereport events can misrepresent that
things are worse than they seem. Ideally the zpool events and the
corresponding vdev stat error counts in a zpool status should be
for unique errors -- not the same error being counted over and over.
This can be demonstrated in a simple example. With a single bad
block in a datafile and just 5 reads of the file we end up with a
degraded vdev, even though there is only one unique error in the pool.
The proposed solution to the above issue, is to eliminate duplicates
when posting events and when updating vdev error stats. We now save
recent error events of interest when posting events so that we can
easily check for duplicates when posting an error.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10861
If a `zfs_space_check_t` other than `ZFS_SPACE_CHECK_NONE` is used with
`dsl_sync_task_nowait()`, the sync task may fail due to ENOSPC.
However, there is no way to notice or communicate this failure, so it's
extremely difficult to use this functionality correctly, and in fact
almost all callers use `ZFS_SPACE_CHECK_NONE`.
This commit removes the `zfs_space_check_t` argument from
`dsl_sync_task_nowait()`, and always uses `ZFS_SPACE_CHECK_NONE`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10855
There are a number of places where cv_?_sig is used simply for
accounting purposes but the surrounding code has no ability to
cope with actually receiving a signal. On FreeBSD it is possible
to send signals to individual kernel threads so this could
enable undesirable behavior.
This patch adds routines on Linux that will do the same idle
accounting as _sig without making the task interruptible. On
FreeBSD cv_*_idle are all aliases for cv_*
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10843
Allow to rename file systems without remounting if it is possible.
It is possible for file systems with 'mountpoint' property set to
'legacy' or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even
mounted back.
This introduces layering violation, as we need to update
'f_mntfromname' field in statfs structure related to mountpoint (for
the dataset we are renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even
cleaner way - in ZFS-only configuration root file system is ZFS file
system with 'mountpoint' property set to 'legacy'. If root dataset is
named system/rootfs, we can snapshot it (system/rootfs@upgrade), clone
it (system/oldrootfs), update FreeBSD and if it doesn't boot we can
boot back from system/oldrootfs and rename it back to system/rootfs
while it is mounted as /. Before it was not possible, because
unmounting / was not possible.
Authored by: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: Matt Macy <mmacy@freebsd.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10839
For Linux, when zfs is compiled as an in kernel static variant
and the in kernel zstd library is compiled statically into the kernel
a symbol collision will occur. This wrapper header renames all
of the relevant zstd functions to avoid this problem.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#10775
Increase the size of DDT_NAMELEN and MNT_LINE_MAX to appease GCC
snprintf truncation warnings.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris McDonough <chrism@plope.com>
Closes#10712Closes#10766
Many modern devices use physical allocation units that are much
larger than the minimum logical allocation size accessible by
external commands. Two prevalent examples of this are 512e disk
drives (512b logical sector, 4K physical sector) and flash devices
(512b logical sector, 4K or larger allocation block size, and 128k
or larger erase block size). Operations that modify less than the
physical sector size result in a costly read-modify-write or garbage
collection sequence on these devices.
Simply exporting the true physical sector of the device to ZFS would
yield optimal performance, but has two serious drawbacks:
1. Existing pools created with devices that have different logical
and physical block sizes, but were configured to use the logical
block size (e.g. because the OS version used for pool construction
reported the logical block size instead of the physical block
size) will suddenly find that the vdev allocation size has
increased. This can be easily tolerated for active members of
the array, but ZFS would prevent replacement of a vdev with
another identical device because it now appears that the smaller
allocation size required by the pool is not supported by the new
device.
2. The device's physical block size may be too large to be supported
by ZFS. The optimal allocation size for the vdev may be quite
large. For example, a RAID controller may export a vdev that
requires read-modify-write cycles unless accessed using 64k
aligned/sized requests. ZFS currently has an 8k minimum block
size limit.
Reporting both the logical and physical allocation sizes for vdevs
solves these problems. A device may be used so long as the logical
block size is compatible with the configuration. By comparing the
logical and physical block sizes, new configurations can be optimized
and administrators can be notified of any existing pools that are
sub-optimal.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Macy <mmacy@freebsd.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10619
Removing other_size from arc_stats breaks top in 11.x jails
running on HEAD.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10745
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
In FreeBSD trim has defaulted to on for several
years. In order to minimize POLA violations on
import it's important to maintain this default
when importing vendored openzfs in to FreeBSD
base.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10719
We limit the size of nvlists passed to the kernel so a user cannot make
the kernel do an unreasonably large allocation. On FreeBSD this limit
was 128 kiB, which turns out to be a bit too small when doing some
operations involving a large number of datasets or snapshots, for
example replication.
Make this limit tunable, with a platform-specific auto default.
Linux keeps its limit at KMALLOC_MAX_SIZE. FreeBSD uses 1/4 of the
system limit on user wired memory, which allows it to scale depending
on system configuration.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Issue #6572Closes#10706
The ARC caches data in scatter ABD's, which are collections of pages,
which are typically 4K. Therefore, the space used to cache each block
is rounded up to a multiple of 4K. The ABD subsystem tracks this wasted
memory in the `scatter_chunk_waste` kstat. However, the ARC's `size` is
not aware of the memory used by this round-up, it only accounts for the
size that it requested from the ABD subsystem.
Therefore, the ARC is effectively using more memory than it is aware of,
due to the `scatter_chunk_waste`. This impacts observability, e.g.
`arcstat` will show that the ARC is using less memory than it
effectively is. It also impacts how the ARC responds to memory
pressure. As the amount of `scatter_chunk_waste` changes, it appears to
the ARC as memory pressure, so it needs to resize `arc_c`.
If the sector size (`1<<ashift`) is the same as the page size (or
larger), there won't be any waste. If the (compressed) block size is
relatively large compared to the page size, the amount of
`scatter_chunk_waste` will be small, so the problematic effects are
minimal.
However, if using 512B sectors (`ashift=9`), and the (compressed) block
size is small (e.g. `compression=on` with the default `volblocksize=8k`
or a decreased `recordsize`), the amount of `scatter_chunk_waste` can be
very large. On a production system, with `arc_size` at a constant 50%
of memory, `scatter_chunk_waste` has been been observed to be 10-30% of
memory.
This commit adds `scatter_chunk_waste` to `arc_size`, and adds a new
`waste` field to `arcstat`. As a result, the ARC's memory usage is more
observable, and `arc_c` does not need to be adjusted as frequently.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10701
`KMC_KMEM` and `KMC_VMEM` are now unused since all SPL-implemented
caches are `KMC_KVMEM`.
KMC_KMEM: Given the default value of `spl_kmem_cache_kmem_limit`, we
don't use kmalloc to back the SPL caches, instead we use kvmalloc
(KMC_KVMEM). The flag, module parameter, /proc entries, and associated
code are removed.
KMC_VMEM: This flag is not used, and kvmalloc() is always preferable to
vmalloc(). The flag, /proc entries, and associated code are removed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10673
Up until now zpool.cache has always lived in /boot on FreeBSD.
For the sake of compatibility fallback to /boot if zpool.cache
isn't found in /etc/zfs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10720
This was previously moved because nothing else in-tree uses it, but
evidently DilOS uses it out of tree.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#10361Closes#10685
ZFS recv should return a useful error message when an invalid index
property value is provided in the send stream properties nvlist
With a compression= property outside of the understood range:
Before:
```
receiving full stream of zof/zstd_send@send2 into testpool/recv@send2
internal error: Invalid argument
Aborted (core dumped)
```
Note: the recv completes successfully, the abort() is likely just to
make it easier to track the unexpected error code.
After:
```
receiving full stream of zof/zstd_send@send2 into testpool/recv@send2
cannot receive compression property on testpool/recv: invalid property
value received 28.9M stream in 1 seconds (28.9M/sec)
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#10631
The ARC shrinker callback `arc_shrinker_count/_scan()` is invoked by the
kernel's shrinker mechanism when the system is running low on free
pages. This happens via 2 code paths:
1. "direct reclaim": The system is attempting to allocate a page, but we
are low on memory. The ARC shrinker callback is invoked from the
page-allocation code path.
2. "indirect reclaim": kswapd notices that there aren't many free pages,
so it invokes the ARC shrinker callback.
In both cases, the kernel's shrinker code requests that the ARC shrinker
callback release some of its cache, and then it measures how many pages
were released. However, it's measurement of released pages does not
include pages that are freed via `__free_pages()`, which is how the ARC
releases memory (via `abd_free_chunks()`). Rather, the kernel shrinker
code is looking for pages to be placed on the lists of reclaimable pages
(which is separate from actually-free pages).
Because the kernel shrinker code doesn't detect that the ARC has
released pages, it may call the ARC shrinker callback many times,
resulting in the ARC "collapsing" down to `arc_c_min`. This has several
negative impacts:
1. ZFS doesn't use RAM to cache data effectively.
2. In the direct reclaim case, a single page allocation may wait a long
time (e.g. more than a minute) while we evict the entire ARC.
3. Even with the improvements made in 67c0f0dedc ("ARC shrinking blocks
reads/writes"), occasionally `arc_size` may stay above `arc_c` for the
entire time of the ARC collapse, thus blocking ZFS read/write operations
in `arc_get_data_impl()`.
To address these issues, this commit limits the ways that the ARC
shrinker callback can be used by the kernel shrinker code, and mitigates
the impact of arc_is_overflowing() on ZFS read/write operations.
With this commit:
1. We limit the amount of data that can be reclaimed from the ARC via
the "direct reclaim" shrinker. This limits the amount of time it takes
to allocate a single page.
2. We do not allow the ARC to shrink via kswapd (indirect reclaim).
Instead we rely on `arc_evict_zthr` to monitor free memory and reduce
the ARC target size to keep sufficient free memory in the system. Note
that we can't simply rely on limiting the amount that we reclaim at once
(as for the direct reclaim case), because kswapd's "boosted" logic can
invoke the callback an unlimited number of times (see
`balance_pgdat()`).
3. When `arc_is_overflowing()` and we want to allocate memory,
`arc_get_data_impl()` will wait only for a multiple of the requested
amount of data to be evicted, rather than waiting for the ARC to no
longer be overflowing. This allows ZFS reads/writes to make progress
even while the ARC is overflowing, while also ensuring that the eviction
thread makes progress towards reducing the total amount of memory used
by the ARC.
4. The amount of memory that the ARC always tries to keep free for the
rest of the system, `arc_sys_free` is increased.
5. Now that the shrinker callback is able to provide feedback to the
kernel's shrinker code about our progress, we can safely enable
the kswapd hook. This will allow the arc to receive notifications
when memory pressure is first detected by the kernel. We also
re-enable the appropriate kstats to track these callbacks.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10600
Renamed to avoid conflicting with refcount.h when a different
implementation is already provided by the platform.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10620
When debugging issues or generally analyzing the runtime of
a system it would be nice to be able to tell the different
ZTHRs running by name rather than having to analyze their
stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#10630
FreeBSD defines _BIG_ENDIAN BIG_ENDIAN _LITTLE_ENDIAN
LITTLE_ENDIAN on every architecture. Trying to do
cross builds whilst hiding this from ZFS has proven
extremely cumbersome.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10621
This is a step toward being able to vendor the OpenZFS code in FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10625
* libspl: umem: These are obviously and intentionally unused; annotate
them as such to appease -Wunused-parameter builds that include this
header.
* sys/dmu.h: In this case, clear_on_evict_dbufp is only used for
ZFS_DEBUG builds, so annotate it as __maybe_unused to appease
-Wunused-parameter.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#10606
Drop unnecessary redefinition's of several arcstat values.
Put missing extern declaration of arc_no_grow_shift in arc_impl.h.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10609
The process of evicting data from the ARC is referred to as
`arc_adjust`.
This commit changes the term to `arc_evict`, which is more specific.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10592
These tunables were renamed from vfs.zfs.arc_min and
vfs.zfs.arc_max to vfs.zfs.arc.min and vfs.zfs.arc.max.
Add legacy compat tunables for the old names.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10579
Livelists and spacemaps are data structures that are logs of allocations
and frees. Livelists entries are block pointers (blkptr_t). Spacemaps
entries are ranges of numbers, most often used as to track
allocated/freed regions of metaslabs/vdevs.
These data structures can become self-inconsistent, for example if a
block or range can be "double allocated" (two allocation records without
an intervening free) or "double freed" (two free records without an
intervening allocation).
ZDB (as well as zfs running in the kernel) can detect these
inconsistencies when loading livelists and metaslab. However, it
generally halts processing when the error is detected.
When analyzing an on-disk problem, we often want to know the entire set
of inconsistencies, which is not possible with the current behavior.
This commit adds a new flag, `zdb -y`, which analyzes the livelist and
metaslab data structures and displays all of their inconsistencies.
Note that this is different from the leak detection performed by
`zdb -b`, which checks for inconsistencies between the spacemaps and the
tree of block pointers, but assumes the spacemaps are self-consistent.
The specific checks added are:
Verify livelists by iterating through each sublivelists and:
- report leftover FREEs
- report double ALLOCs and double FREEs
- record leftover ALLOCs together with their TXG [see Cross Check]
Verify spacemaps by iterating over each metaslab and:
- iterate over spacemap and then the metaslab's entries in the
spacemap log, then report any double FREEs and double ALLOCs
Verify that livelists are consistenet with spacemaps. The space
referenced by livelists (after using the FREE's to cancel out
corresponding ALLOCs) should be allocated, according to the spacemaps.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sara Hartse <sara.hartse@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
External-issue: DLPX-66031
Closes#10515
Brian Behlendorf
Alexander Motin
Matthew Macy
loli10K
Matthew Ahrens
Mateusz Guzik
Ryan Moeller
Warner Losh
Christian Schwarz
Sebastian Gottschall
George Wilson
Toomas Soome
Ryan Moeller
Don Brady
Chris McDonough
Michael Niewöhner
Allan Jude
Serapheim Dimitropoulos
Matthew Macy
Kyle Evans