Reduce the time required for ./configure to perform the needed
KABI checks by allowing kbuild to compile multiple test cases in
parallel. This was accomplished by splitting each test's source
code from the logic handling whether that code could be compiled
or not.
By introducing this split it's possible to minimize the number of
times kbuild needs to be invoked. As importantly, it means all of
the tests can be built in parallel. This does require a little extra
care since we expect some tests to fail, so the --keep-going (-k)
option must be provided otherwise some tests may not get compiled.
Furthermore, since a failure during the kbuild modpost phase will
result in an early exit; the final linking phase is limited to tests
which passed the initial compilation and produced an object file.
Once everything has been built the configure script proceeds as
previously. The only significant difference is that it now merely
needs to test for the existence of a .ko file to determine the
result of a given test. This vastly speeds up the entire process.
New test cases should use ZFS_LINUX_TEST_SRC to declare their test
source code and ZFS_LINUX_TEST_RESULT to check the result. All of
the existing kernel-*.m4 files have been updated accordingly, see
config/kernel-current-time.m4 for a basic example. The legacy
ZFS_LINUX_TRY_COMPILE macro has been kept to handle special cases
but it's use is not encouraged.
master (secs) patched (secs)
------------- ----------------
autogen.sh 61 68
configure 137 24 (~17% of current run time)
make -j $(nproc) 44 44
make rpms 287 150
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#8547Closes#9132Closes#9341
Certain versions of gcc generate an 'unrecognized command
line option' error message when -Wunused-but-set-variable
is used unconditionally. This in turn can cause several
of the autoconf tests to misdetect an interface.
Now, the use of -Wunused-but-set-variable in the autoconf
tests was introduced by commit b9c59ec8 to address a gcc
4.6 compatibility problem. So we really only need to pass
this option for version of gcc which are known to support it.
Therefore, the tests have been updated to use the result of
the existing ZFS_AC_CONFIG_ALWAYS_NO_UNUSED_BUT_SET_VARIABLE
which determines if gcc supports this option.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#1004
The Linux block device queue subsystem exposes a number of configurable
settings described in Linux block/blk-settings.c. The defaults for these
settings are tuned for hard drives, and are not optimized for ZVOLs. Proper
configuration of these options would allow upper layers (I/O scheduler) to
take better decisions about write merging and ordering.
Detailed rationale:
- max_hw_sectors is set to unlimited (UINT_MAX). zvol_write() is able to
handle writes of any size, so there's no reason to impose a limit. Let the
upper layer decide.
- max_segments and max_segment_size are set to unlimited. zvol_write() will
copy the requests' contents into a dbuf anyway, so the number and size of
the segments are irrelevant. Let the upper layer decide.
- physical_block_size and io_opt are set to the ZVOL's block size. This
has the potential to somewhat alleviate issue #361 for ZVOLs, by warning
the upper layers that writes smaller than the volume's block size will be
slow.
- The NONROT flag is set to indicate this isn't a rotational device.
Although the backing zpool might be composed of rotational devices, the
resulting ZVOL often doesn't exhibit the same behavior due to the COW
mechanisms used by ZFS. Setting this flag will prevent upper layers from
making useless decisions (such as reordering writes) based on incorrect
assumptions about the behavior of the ZVOL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Brian Behlendorf
Etienne Dechamps