This feature allows disks to be added one at a time to a RAID-Z group,
expanding its capacity incrementally. This feature is especially useful
for small pools (typically with only one RAID-Z group), where there
isn't sufficient hardware to add capacity by adding a whole new RAID-Z
group (typically doubling the number of disks).
== Initiating expansion ==
A new device (disk) can be attached to an existing RAIDZ vdev, by
running `zpool attach POOL raidzP-N NEW_DEVICE`, e.g. `zpool attach tank
raidz2-0 sda`. The new device will become part of the RAIDZ group. A
"raidz expansion" will be initiated, and the new device will contribute
additional space to the RAIDZ group once the expansion completes.
The `feature@raidz_expansion` on-disk feature flag must be `enabled` to
initiate an expansion, and it remains `active` for the life of the pool.
In other words, pools with expanded RAIDZ vdevs can not be imported by
older releases of the ZFS software.
== During expansion ==
The expansion entails reading all allocated space from existing disks in
the RAIDZ group, and rewriting it to the new disks in the RAIDZ group
(including the newly added device).
The expansion progress can be monitored with `zpool status`.
Data redundancy is maintained during (and after) the expansion. If a
disk fails while the expansion is in progress, the expansion pauses
until the health of the RAIDZ vdev is restored (e.g. by replacing the
failed disk and waiting for reconstruction to complete).
The pool remains accessible during expansion. Following a reboot or
export/import, the expansion resumes where it left off.
== After expansion ==
When the expansion completes, the additional space is available for use,
and is reflected in the `available` zfs property (as seen in `zfs list`,
`df`, etc).
Expansion does not change the number of failures that can be tolerated
without data loss (e.g. a RAIDZ2 is still a RAIDZ2 even after
expansion).
A RAIDZ vdev can be expanded multiple times.
After the expansion completes, old blocks remain with their old
data-to-parity ratio (e.g. 5-wide RAIDZ2, has 3 data to 2 parity), but
distributed among the larger set of disks. New blocks will be written
with the new data-to-parity ratio (e.g. a 5-wide RAIDZ2 which has been
expanded once to 6-wide, has 4 data to 2 parity). However, the RAIDZ
vdev's "assumed parity ratio" does not change, so slightly less space
than is expected may be reported for newly-written blocks, according to
`zfs list`, `df`, `ls -s`, and similar tools.
Sponsored-by: The FreeBSD Foundation
Sponsored-by: iXsystems, Inc.
Sponsored-by: vStack
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Authored-by: Matthew Ahrens <mahrens@delphix.com>
Contributions-by: Fedor Uporov <fuporov.vstack@gmail.com>
Contributions-by: Stuart Maybee <stuart.maybee@comcast.net>
Contributions-by: Thorsten Behrens <tbehrens@outlook.com>
Contributions-by: Fmstrat <nospam@nowsci.com>
Contributions-by: Don Brady <dev.fs.zfs@gmail.com>
Signed-off-by: Don Brady <dev.fs.zfs@gmail.com>
Closes#15022
Fix minor cstyle warnings accidentally introduced by 7145123b.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10143
This change adds a separate return code to zfs_ioc_recv that is used
for incomplete streams, in addition to the existing return code for
streams that contain corruption.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10122
FreeBSD doesn't have EBADE, ECHRNG, or ETIME.
Add constants for these and set them appropriately for the platform.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10061
This feature allows copying existing bookmarks using
zfs bookmark fs#target fs#newbookmark
There are some niche use cases for such functionality,
e.g. when using bookmarks as markers for replication progress.
Copying redaction bookmarks produces a normal bookmark that
cannot be used for redacted send (we are not duplicating
the redaction object).
ZCP support for bookmarking (both creation and copying) will be
implemented in a separate patch based on this work.
Overview:
- Terminology:
- source = existing snapshot or bookmark
- new/bmark = new bookmark
- Implement bookmark copying in `dsl_bookmark.c`
- create new bookmark node
- copy source's `zbn_phys` to new's `zbn_phys`
- zero-out redaction object id in copy
- Extend existing bookmark ioctl nvlist schema to accept
bookmarks as sources
- => `dsl_bookmark_create_nvl_validate` is authoritative
- use `dsl_dataset_is_before` check for both snapshot
and bookmark sources
- Adjust CLI
- refactor shortname expansion logic in `zfs_do_bookmark`
- Update man pages
- warn about redaction bookmark handling
- Add test cases
- CLI
- pyyzfs libzfs_core bindings
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#9571
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#9235
zfs create, receive and rename can bypass this hierarchy rule. Update
both userland and kernel module to prevent this issue and use pyzfs
unit tests to exercise the ioctls directly.
Note: this commit slightly changes zfs_ioc_create() ABI. This allow to
differentiate a generic error (EINVAL) from the specific case where we
tried to create a dataset below a ZVOL (ZFS_ERR_WRONG_PARENT).
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Matt Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
These changes are efficient and valid in python 2 and 3. For the
most part, they are also pythonic.
* 2to3 conversion
* add __future__ imports
* iterator changes
* integer division
* relative import fixes
Reviewed-by: John Ramsden <johnramsden@riseup.net>
Reviewed-by: Neal Gompa <ngompa@datto.com>
Reviewed-by: loli10K <ezomori.nozomu@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <antonio.e.russo@gmail.com>
Closes#8096
This change adds the following libzfs_core functions to pyzfs:
lzc_remap, lzc_pool_checkpoint, lzc_pool_checkpoint_discard
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7793Closes#7800
This commit introduces several changes:
* Update LICENSE and project information
* Give a good PEP8 talk to existing Python source code
* Add RPM/DEB packaging for pyzfs
* Fix some outstanding issues with the existing pyzfs code caused by
changes in the ABI since the last time the code was updated
* Integrate pyzfs Python unittest with the ZFS Test Suite
* Add missing libzfs_core functions: lzc_change_key,
lzc_channel_program, lzc_channel_program_nosync, lzc_load_key,
lzc_receive_one, lzc_receive_resumable, lzc_receive_with_cmdprops,
lzc_receive_with_header, lzc_reopen, lzc_send_resume, lzc_sync,
lzc_unload_key, lzc_remap
Note: this commit slightly changes zfs_ioc_unload_key() ABI. This allow
to differentiate the case where we tried to unload a key on a
non-existing dataset (ENOENT) from the situation where a dataset has
no key loaded: this is consistent with the "change" case where trying
to zfs_ioc_change_key() from a dataset with no key results in EACCES.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7230
libzfs_core is intended to be a stable interface for programmatic
administration of ZFS.
This wrapper provides one-to-one wrappers for libzfs_core API functions,
but the signatures and types are more natural to Python.
nvlists are wrapped as dictionaries or lists depending on their usage.
Some parameters have default values depending on typical use for
increased convenience.
Enumerations and bit flags become strings and lists of strings in
Python.
Errors are reported as exceptions rather than integer errno-style
error codes. The wrapper takes care to provide one-to-many mapping
of the error codes to the exceptions by interpreting a context
in which the error code is produced.
Unit tests and automated test for the libzfs_core API are provided
with this package.
Please note that the API tests perform lots of ZFS dataset level
operations and ZFS tries hard to ensure that any modifications
do reach stable storage. That means that the operations are done
synchronously and that, for example, disk caches are flushed.
Thus, the tests can be very slow on real hardware.
It is recommended to place the default temporary directory or
a temporary directory specified by, for instance, TMP environment
variable on a memory backed filesystem.
Original-patch-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported-by: loli10K <ezomori.nozomu@gmail.com>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#7230
Don Brady
Brian Behlendorf
Paul Dagnelie
Ryan Moeller
Christian Schwarz
Andrea Gelmini
loli10K
Antonio Russo
loli10K
Andriy Gapon