With Linux v6.6.x and clang 16, a configure step fails on a warning that
later results in an error while building, due to 'ts' being
uninitialized. Add a trivial initialization to silence the warning.
Signed-off-by: Jaron Kent-Dobias <jaron@kent-dobias.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
If all zfs dkms modules have been removed, a shell-init error message
may appear, because /var/lib/dkms/zfs does no longer exist.
Resolve this by leaving the directory earlier on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mart Frauenlob <AllKind@fastest.cc>
Closes#15576
It was broken for several reasons:
* VOP_UNLOCK lost an argument in 13.0. So OpenZFS should be using
VOP_UNLOCK1, but a few direct calls to VOP_UNLOCK snuck in.
* The location of the zlib header moved in 13.0 and 12.1. We can drop
support for building on 12.0, which is EoL.
* knlist_init lost an argument in 13.0. OpenZFS change 9d0887402b
assumed 13.0 or later.
* FreeBSD 13.0 added copy_file_range, and OpenZFS change 67a1b03791
assumed 13.0 or later.
Sponsored-by: Axcient
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#15551
Previously, dmu_buf_will_clone() would roll back any dirty record, but
would not clean out the modified data nor reset the state before
releasing the lock. That leaves the last-written data in db_data, but
the dbuf in the wrong state.
This is eventually corrected when the dbuf state is made NOFILL, and
dbuf_noread() called (which clears out the old data), but at this point
its too late, because the lock was already dropped with that invalid
state.
Any caller acquiring the lock before the call into
dmu_buf_will_not_fill() can find what appears to be a clean, readable
buffer, and would take the wrong state from it: it should be getting the
data from the cloned block, not from earlier (unwritten) dirty data.
Even after the state was switched to NOFILL, the old data was still not
cleaned out until dbuf_noread(), which is another gap for a caller to
take the lock and read the wrong data.
This commit fixes all this by properly cleaning up the previous state
and then setting the new state before dropping the lock. The
DBUF_VERIFY() calls confirm that the dbuf is in a valid state when the
lock is down.
Sponsored-by: Klara, Inc.
Sponsored-By: OpenDrives Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15566Closes#15526
zdb with '-e' or exported zpool doesn't work along with
'-O' and '-r' options as we process them before '-e' has
been processed.
Below errors are seen:
~> zdb -e pool-mds65/mdt65 -O oi.9/0x200000009:0x0:0x0
failed to hold dataset 'pool-mds65/mdt65': No such file or directory
~> zdb -e pool-oss0/ost0 -r file1 /tmp/filecopy1 -p.
failed to hold dataset 'pool-oss0/ost0': No such file or directory
zdb: internal error: No such file or directory
We need to make sure to process '-O|-r' options after the
'-e' option has been processed, which imports the pool to
the namespace if it's not in the cachefile.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#15532
Same idea as the dedup stats, but for block cloning.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15541
So that zdb (and others!) can get at the BRT on-disk structures.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Norris <robn@despairlabs.com>
Closes#15541
The zfs_load-key tests were failing on F39 due to their use of the
deprecated ssl.wrap_socket function. This commit updates the test to
instead use ssl.SSLContext() as described in
https://stackoverflow.com/a/65194957.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15534Closes#15550
In case of crash cloned blocks need to be claimed on pool import.
It is only possible if they (lr_bps) and their count (lr_nbps) are
not encrypted but only authenticated, similar to block pointer in
lr_write_t. Few other fields can be and are still encrypted.
This should fix panic on ZIL claim after crash when block cloning
is actively used.
Reviewed-by: Richard Yao <richard.yao@alumni.stonybrook.edu>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Reviewed-by: Sean Eric Fagan <sef@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Edmund Nadolski <edmund.nadolski@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15543Closes#15513
Over its history this the dirty dnode test has been changed between
checking for a dnodes being on `os_dirty_dnodes` (`dn_dirty_link`) and
`dn_dirty_record`.
de198f2d9 Fix lseek(SEEK_DATA/SEEK_HOLE) mmap consistency
2531ce372 Revert "Report holes when there are only metadata changes"
ec4f9b8f3 Report holes when there are only metadata changes
454365bba Fix dirty check in dmu_offset_next()
66aca2473 SEEK_HOLE should not block on txg_wait_synced()
Also illumos/illumos-gate@c543ec060dillumos/illumos-gate@2bcf0248e9
It turns out both are actually required.
In the case of appending data to a newly created file, the dnode proper
is dirtied (at least to change the blocksize) and dirty records are
added. Thus, a single logical operation is represented by separate
dirty indicators, and must not be separated.
The incorrect dirty check becomes a problem when the first block of a
file is being appended to while another process is calling lseek to skip
holes. There is a small window where the dnode part is undirtied while
there are still dirty records. In this case, `lseek(fd, 0, SEEK_DATA)`
would not know that the file is dirty, and would go to
`dnode_next_offset()`. Since the object has no data blocks yet, it
returns `ESRCH`, indicating no data found, which results in `ENXIO`
being returned to `lseek()`'s caller.
Since coreutils 9.2, `cp` performs sparse copies by default, that is, it
uses `SEEK_DATA` and `SEEK_HOLE` against the source file and attempts to
replicate the holes in the target. When it hits the bug, its initial
search for data fails, and it goes on to call `fallocate()` to create a
hole over the entire destination file.
This has come up more recently as users upgrade their systems, getting
OpenZFS 2.2 as well as a newer coreutils. However, this problem has been
reproduced against 2.1, as well as on FreeBSD 13 and 14.
This change simply updates the dirty check to check both types of dirty.
If there's anything dirty at all, we immediately go to the "wait for
sync" stage, It doesn't really matter after that; both changes are on
disk, so the dirty fields should be correct.
Sponsored-by: Klara, Inc.
Sponsored-by: Wasabi Technology, Inc.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Rob Norris <rob.norris@klarasystems.com>
Closes#15571Closes#15526
This reverts commit bd7a02c251 which
can trigger an unlikely existing bio alignment issue on Linux.
This change is good, but the underlying issue it exposes needs to
be resolved before this can be re-applied.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #15533
Many tests are failing on AlmaLinux 9 because ZTS could not destroy the
pool in cleanup. This was due to $PWD being set to '.' instead of the
expected full path. This patch sets $PWD to the full path.
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Copy the disable parameter that FreeBSD implemented, and extend it to
work on Linux as well, until we're sure this is stable.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#15529
Auto-generate changelog based off on @VERSION@ during configure,
so that it is not needed to be update with new releases / version
updates.
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Update the META file to reflect compatibility with the 6.6 kernel.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Umer Saleem <usaleem@ixsystems.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15520
This gets around UBSAN errors when using arrays at the end of
structs. It converts some zero-length arrays to variable length
arrays and disables UBSAN checking on certain modules.
It is based off of the patch from #15460.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Tested-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Co-authored-by: Thomas Lamprecht <t.lamprecht@proxmox.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Issue #15145Closes#15510
zpool_create_features_007_pos only tested for compat-2020 feature
set. It would be useful to test for all known features sets. If
any additional feature is found enabled that is not present in
compatibility list or feature set, it should be caught and
reported earlier.
This commit also removes encryption from openzfsonosx-1.8.1
compatibility list. Encryption enables bookmark_v2, since it is
a dependency of encryption, but not listed in openzfsonoxx-1.8.1
compatibility list.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15505
This commit updates zpool-features.7 man page to add newly added
zpool features to grub2 compatibility list.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15505
As shown in #15404#issuecomment-1765002181, Ubuntu kernel has
'Provides: zfs-dkms', which will cause uninstall of the kernel, when
attempting to install openzfs-zfs-dkms.
As a workaround remove the 'Conflicts: zfs-dkms' definition from
the debian control file.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mart Frauenlob <AllKind@fastest.cc>
Closes#15503
Private read/write mapping can't be used to modify the mapped files, so
they will remain be immutable. Private read/write mappings are usually
used to load the data segment of executable files, rejecting them will
rendering immutable executable files to stop working.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: WHR <msl0000023508@gmail.com>
Closes#15344
Currently vdev_queue_class_length is responsible for checking how long
the queue length is, however, it doesn't check the length when a list
is used, rather it just returns whether it is empty or not. To fix this
I added a counter variable to vdev_queue_class to keep track of the sync
IO ops, and changed vdev_queue_class_length to reference this variable
instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: MigeljanImeri <ImeriMigel@gmail.com>
Closes#15478
With Linux v6.6.0 and GCC 12, when debug build is configured,
implicit conversion error is raised while converting
'enum <anonymous>' to 'boolean_t'. Use 'B_TRUE' instead of
'true' to fix the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Snajdr <snajpa@snajpa.net>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15489
PR#15459 add all read-only compatible zpool features to grub2
compatibility list. 'obsolete_counts' is a read-only features that
depends on 'device_removal' feature which is not read-only and
is marked as ZFEATURE_FLAG_MOS. Creating a pool with grub2
compatibility enables 'device_removal' feature as well, which is
not desired.
This commit removes the 'obsolete_counts' feature from
grub2 compatibility list, as GRUB only supports read-only
compatible features.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15499
Alien does not honour the %posttrans hook.
So move the dkms uninstall/install scripts to the
%pre/%post hooks in case of package install/upgrade.
In case of package removal, handle that in %preun.
Add removal of all old dkms modules.
Add checking for broken 'dkms status'. Handle that as
good as possible and warn the user about it.
Also add more verbose messages about what we are doing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mart Frauenlob <AllKind@fastest.cc>
Closes#15415
GRUB opens the boot pool in read-only mode. All read-only
compatible features for zpool can be enabled and added to
grub2 compatibility, as GRUB does not open the boot-pool
for write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#15459
There is no sense to have separate implementations for FreeBSD and
Linux. Make Linux code shared as more functional and just register
FreeBSD-specific prune callback with arc_add_prune_callback() API.
Aside of code cleanup this should fix excessive pruning on FreeBSD:
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=274698
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15456
We should not always use PAGESIZE alignment for caches bigger than
it and SPA_MINBLOCKSIZE otherwise. Doing that caches for 5, 6, 7,
10 and 14KB rounded up to 8, 12 and 16KB respectively make no sense.
Instead specify as alignment the biggest power-of-2 divisor. This
way 2KB and 6KB caches are both aligned to 2KB, while 4KB and 8KB
are aligned to 4KB.
Reduce number of caches to half-power of 2 instead of quarter-power
of 2. This removes caches difficult for underlying allocators to
fit into page-granular slabs, such as: 2.5, 3.5, 5, 7, 10KB, etc.
Since these caches are mostly used for transient allocations like
ZIOs and small DBUF cache it does not worth being too aggressive.
Due to the above alignment issue some of those caches were not
working properly any way. 6KB cache now finally has a chance to
work right, placing 2 buffers into 3 pages, that makes sense.
Remove explicit alignment in Linux user-space case. I don't think
it should be needed any more with the above fixes.
As result on FreeBSD instead of such numbers of pages per slab:
vm.uma.zio_buf_comb_16384.keg.ppera: 4
vm.uma.zio_buf_comb_14336.keg.ppera: 4
vm.uma.zio_buf_comb_12288.keg.ppera: 3
vm.uma.zio_buf_comb_10240.keg.ppera: 3
vm.uma.zio_buf_comb_8192.keg.ppera: 2
vm.uma.zio_buf_comb_7168.keg.ppera: 2
vm.uma.zio_buf_comb_6144.keg.ppera: 2 <= Broken
vm.uma.zio_buf_comb_5120.keg.ppera: 2
vm.uma.zio_buf_comb_4096.keg.ppera: 1
vm.uma.zio_buf_comb_3584.keg.ppera: 7 <= Hard to free
vm.uma.zio_buf_comb_3072.keg.ppera: 3
vm.uma.zio_buf_comb_2560.keg.ppera: 2
vm.uma.zio_buf_comb_2048.keg.ppera: 1
vm.uma.zio_buf_comb_1536.keg.ppera: 2
vm.uma.zio_buf_comb_1024.keg.ppera: 1
vm.uma.zio_buf_comb_512.keg.ppera: 1
I am now getting such:
vm.uma.zio_buf_comb_16384.keg.ppera: 4
vm.uma.zio_buf_comb_12288.keg.ppera: 3
vm.uma.zio_buf_comb_8192.keg.ppera: 2
vm.uma.zio_buf_comb_6144.keg.ppera: 3 <= Fixed, 2 in 3 pages
vm.uma.zio_buf_comb_4096.keg.ppera: 1
vm.uma.zio_buf_comb_3072.keg.ppera: 3
vm.uma.zio_buf_comb_2048.keg.ppera: 1
vm.uma.zio_buf_comb_1536.keg.ppera: 2
vm.uma.zio_buf_comb_1024.keg.ppera: 1
vm.uma.zio_buf_comb_512.keg.ppera: 1
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15452
dmu_tx_check_ioerr() pre-reads blocks that are going to be dirtied
as part of transaction to both prefetch them and check for errors.
But it makes no sense to do it for holes, since there are no disk
reads to prefetch and there can be no errors. On the other side
those blocks are anonymous, and they are freed immediately by the
dbuf_rele() without even being put into dbuf cache, so we just
burn CPU time on decompression and overheads and get absolutely
no result at the end.
Use of dbuf_hold_impl() with fail_sparse parameter allows to skip
the extra work, and on my tests with sequential 8KB writes to empty
ZVOL with 32KB blocks shows throughput increase from 1.7 to 2GB/s.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15371
In Linux commit 560e20e4bf6484a0c12f9f3c7a1aa55056948e1e, the
fsync_bdev() function was removed in favor of sync_blockdev() to do
(roughly) the same thing, given the same input. This change
conditionally attempts to call sync_blockdev() if fsync_bdev() isn't
discovered during configure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263
In commit 0d72b92883c651a11059d93335f33d65c6eb653b, a new u32 argument
for the request_mask was added to generic_fillattr. This is the same
request_mask for statx that's present in the most recent API implemented
by zpl_getattr_impl. This commit conditionally adds it to the
zpl_generic_fillattr(...) macro, as well as the zfs_getattr_fast(...)
implementation, when configure determines it's present in the kernel's
generic_fillattr(...).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263
In Linux commit 13bc24457850583a2e7203ded05b7209ab4bc5ef, direct access
to the i_ctime member of struct inode was removed. The new approach is
to use accessor methods that exclusively handle passing the timestamp
around by value. This change adds new tests for each of these functions
and introduces zpl_* equivalents in include/os/linux/zfs/sys/zpl.h. In
where the inode_get/set_ctime*() functions exist, these zpl_* calls will
be mapped to the new functions. On older kernels, these macros just wrap
direct-access calls. The code that operated on an address of ip->i_ctime
to call ZFS_TIME_DECODE() now will take a local copy using
zpl_inode_get_ctime(), and then pass the address of the local copy when
performing the ZFS_TIME_DECODE() call, in all cases, rather than
directly accessing the member.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#15263Closes#15257
Prefetched buffers are currently read from L2ARC if, and only if,
l2arc_noprefetch is set to non-default value of 0. This means that
a streaming read which can be served from L2ARC will instead engage
the main pool.
For example, consider what happens when a file is sequentially read:
- application requests contiguous data, engaging the prefetcher;
- ARC buffers are initially marked as prefetched but, as the calling
application consumes data, the prefetch tag is cleared;
- these "normal" buffers become eligible for L2ARC and are copied to it;
- re-reading the same file will *not* engage L2ARC even if it contains
the required buffers;
- main pool has to suffer another sequential read load, which (due to
most NCQ-enabled HDDs preferring sequential loads) can dramatically
increase latency for uncached random reads.
In other words, current behavior is to write data to L2ARC (wearing it)
without using the very same cache when reading back the same data. This
was probably useful many years ago to preserve L2ARC read bandwidth but,
with current SSD speed/size/price, it is vastly sub-optimal.
Setting l2arc_noprefetch=1, while enabling L2ARC to serve these reads,
means that even prefetched but unused buffers will be copied into L2ARC,
further increasing wear and load for potentially not-useful data.
This patch enable prefetched buffer to be read from L2ARC even when
l2arc_noprefetch=1 (default), increasing sequential read speed and
reducing load on the main pool without polluting L2ARC with not-useful
(ie: unused) prefetched data. Moreover, it clear users confusion about
L2ARC size increasing but not serving any IO when doing sequential
reads.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Gionatan Danti <g.danti@assyoma.it>
Closes#15451
Many long-running ZFS ioctls lock the spa_namespace_lock, forcing
concurrent ioctls to sleep for the mutex. Previously, the only
option is to call mutex_enter() which sleeps uninterruptibly. This
is a usability issue for sysadmins, for example, if the admin runs
`zpool status` while a slow `zpool import` is ongoing, the admin's
shell will be locked in uninterruptible sleep for a long time.
This patch resolves this admin usability issue by introducing
mutex_enter_interruptible() which sleeps interruptibly while waiting
to acquire a lock. It is implemented for both Linux and FreeBSD.
The ZFS_IOC_POOL_CONFIGS ioctl, used by `zpool status`, is changed to
use this new macro so that the command can be interrupted if it is
issued during a concurrent `zpool import` (or other long-running
operation).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Thomas Bertschinger <bertschinger@lanl.gov>
Closes#15360
This reverts commit aefb6a2bd6.
aefb6a2bd temporally disabled blk-mq until we could fix a fix for
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15439
This fix removes a dubious optimization in zfs_uiomove_bvec_rq()
that saved the iterator contents of a rq_for_each_segment(). This
optimization allowed restoring the "saved state" from a previous
rq_for_each_segment() call on the same uio so that you wouldn't
need to iterate though each bvec on every zfs_uiomove_bvec_rq() call.
However, if the kernel is manipulating the requests/bios/bvecs under
the covers between zfs_uiomove_bvec_rq() calls, then it could result
in corruption from using the "saved state". This optimization
results in an unbootable system after installing an OS on a zvol
with blk-mq enabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15351
The first occurrence should be "ARC prefetch data accesses:"
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: ofthesun9 <olivier@ofthesun.net>
Closes#15427
In my understanding ARC_BUF_SHARED() and arc_buf_is_shared() should
return identical results, except the second also asserts it deeper.
The first is much cheaper though, saving few pointer dereferences.
Replace production arc_buf_is_shared() calls with ARC_BUF_SHARED(),
and call arc_buf_is_shared() in random assertions, while making it
even more strict.
On my tests this in half reduces arc_buf_destroy_impl() time, that
noticeably reduces hash_lock congestion under heavy dbuf eviction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15397
Torn reads/writes of dp_dirty_total are unlikely: on 64-bit systems
due to register size, while on 32-bit due to memory constraints.
And even if we hit some race, the code implementing the delay takes
the lock any way.
Removal of the poll-wide lock acquisition saves ~1% of CPU time on
8-thread 8KB write workload.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15390
Once we trigger the zpool scrub, all zpool/zfs command gets stuck for
180 seconds. Post 180 seconds zpool/zfs commands gets start executing
however few more seconds(10s) it take to update the status. hence
sleeping for 200 seconds so that we get the correct status.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: vaibhav.bhanawat <vaibhav.bhanawat@delphix.com>
Closes#15364
We already use ____cacheline_aligned in many places, so add one more
instead of seems arbitrary char tc_pad[8].
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15402
Reviewed-by: Rob N <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Dennis R. Friedrichsen <dennis.r.friedrichsen@gmail.com>
Closes#15417
Variable 'uma_align_cache' has not been used since commit "FreeBSD: Use
a hash table for taskqid lookups" (3933305ea). Moreover, it is soon
going to become private to FreeBSD's UMA in 15.0-CURRENT (main),
14.0-STABLE (stable/14) and 13.2-STABLE (stable/13). Should accessing
this information become necessary again, one will have to use the new
accessors for recent versions.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olivier Certner <olce.freebsd@certner.fr>
Closes#15416
When a vdev is to be expanded -- either via `zpool online -e` or via
the autoexpand option -- a SPA_ASYNC_CONFIG_UPDATE request is queued
to be handled via an asynchronous worker thread (spa_async_thread).
This normally happens almost immediately; but will be delayed up to
zfs_ccw_retry_interval seconds (default 5 minutes) if an attempt to
write the zpool configuration cache failed.
When FreeBSD boots ZFS-root VM images generated using `makefs -t zfs`,
the zpoolupgrade rc.d script runs `zpool upgrade`, which modifies the
pool configuration and triggers an attempt to write to the cache file.
This attempted write fails because the filesystem is still mounted
read-only at this point in the boot process, triggering a 5-minute
cooldown before SPA_ASYNC_CONFIG_UPDATE requests will be handled by
the asynchronous worker thread.
When expanding a vdev, reset the "when did a configuration cache
write last fail" value so that the SPA_ASYNC_CONFIG_UPDATE request
will be handled promptly. A cleaner but more intrusive option would
be to use separate SPA_ASYNC_ flags for "configuration changed" and
"try writing the configuration cache again", but with FreeBSD 14.0
coming very soon I'd prefer to leave such refactoring for a later
date.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colin Percival <cperciva@FreeBSD.org>
Closes#15405
The change is simple -- restore the original code so that the VDEV
path is updated when using by-id paths. The more challenging part
was to devise a second ZTS test, that would test auto-replace for
'by-id' and help prevent a future regression.
With that new test, we can now do an A|B test with , and without,
the fix to confirm that auto-replace for by-id paths works. The
existing auto-replace test, functional/fault/auto_replace_001_pos,
will confirm that we didn't break auto-replace for 'by-vdev' paths.
In the original functional/fault/auto_replace_001_pos test, the disk
wipe (using dd) was not effective in removing the partitioning since
the kernel was never informed of the wipe.
Added a call to wipefs(8) so that the kernel is informed and ZED will
re-partition the device.
Added a validation step that the re-partitioning occurred by
confirming that the GPT partition UUID changes.
Sponsored-By: OpenDrives Inc.
Sponsored-By: Klara Inc.
Reviewed-by: Rob Norris <rob.norris@klarasystems.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Don Brady <don.brady@klarasystems.com>
Closes#15363
Have libzfs call a special `zfs_prepare_disk` script before a disk is
included into the pool. The user can edit this script to add things
like a disk firmware update or a disk health check. Use of the script
is totally optional. See the zfs_prepare_disk manpage for full details.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#15243
For synchronous write workloads with large IO sizes, a pool configured
with a slog performs worse than one with an embedded zil:
sequential_writes 1m sync ios, 16 threads
Write IOPS: 1292 438 -66.10%
Write Bandwidth: 1323570 448910 -66.08%
Write Latency: 12128400 36330970 3.0x
sequential_writes 1m sync ios, 32 threads
Write IOPS: 1293 430 -66.74%
Write Bandwidth: 1324184 441188 -66.68%
Write Latency: 24486278 74028536 3.0x
The reason is the `zil_slog_bulk` variable. In `zil_lwb_write_open`,
if a zil block is greater than 768K, the priority of the write is
downgraded from sync to async. Increasing the value allows greater
throughput. To select a value for this PR, I ran an fio workload with
the following values for `zil_slog_bulk`:
zil_slog_bulk KiB/s
1048576 422132
2097152 478935
4194304 533645
8388608 623031
12582912 827158
16777216 1038359
25165824 1142210
33554432 1211472
50331648 1292847
67108864 1308506
100663296 1306821
134217728 1304998
At 64M, the results with a slog are now improved to parity with an
embedded zil:
sequential_writes 1m sync ios, 16 threads
Write IOPS: 438 1288 2.9x
Write Bandwidth: 448910 1319062 2.9x
Write Latency: 36330970 12163408 -66.52%
sequential_writes 1m sync ios, 32 threads
Write IOPS: 430 1290 3.0x
Write Bandwidth: 441188 1321693 3.0x
Write Latency: 74028536 24519698 -66.88%
None of the other tests in the performance suite (run with a zil or
slog) had a significant change, including the random_write_zil tests,
which use multiple datasets.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Wren Kennedy <john.kennedy@delphix.com>
Closes#14378
- Group tqent_task and tqent_timeout_task into a union. They are
never used same time. This shrinks taskq_ent_t from 192 to 160 bytes.
- Remove tqent_registered. Use tqent_id != 0 instead.
- Remove tqent_cancelled. Use taskqueue pending counter instead.
- Change tqent_type into uint_t. We don't need to pack it any more.
- Change tqent_rc into uint_t, matching refcount(9).
- Take shared locks in taskq_lookup().
- Call proper taskqueue_drain_timeout() for TIMEOUT_TASK in
taskq_cancel_id() and taskq_wait_id().
- Switch from CK_LIST to regular LIST.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored by: iXsystems, Inc.
Closes#15356
Block cloning from an encrypted dataset into an unencrypted dataset
and vice versa is not possible. The current code did allow cloning
unencrypted files into an encrypted dataset causing a panic when
these were accessed. Block cloning between encrypted and encrypted
is currently supported on the same filesystem only.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Kay Pedersen <mail@mkwg.de>
Reviewed-by: Rob N <robn@despairlabs.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#15464Closes#15465
Jaron Kent-Dobias
AllKind
Alan Somers
Rob N
Akash B
Tony Hutter
Alexander Motin
Brian Behlendorf
Rich Ercolani
Umer Saleem
Low-power
MigeljanImeri
Coleman Kane
shodanshok
Thomas Bertschinger
ofthesun9
VaibhavB
dennisfriedrichsen
Olivier Certner
Colin Percival
Don Brady
John Wren Kennedy
Martin Matuška