Commit Graph

8 Commits

Author SHA1 Message Date
George.Wilson cc92e9d0c3 3246 ZFS I/O deadman thread
Reviewed by: Matt Ahrens <matthew.ahrens@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Christopher Siden <chris.siden@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>

NOTES: This patch has been reworked from the original in the
following ways to accomidate Linux ZFS implementation

*) Usage of the cyclic interface was replaced by the delayed taskq
   interface.  This avoids the need to implement new compatibility
   code and allows us to rely on the existing taskq implementation.

*) An extern for zfs_txg_synctime_ms was added to sys/dsl_pool.h
   because declaring externs in source files as was done in the
   original patch is just plain wrong.

*) Instead of panicing the system when the deadman triggers a
   zevent describing the blocked vdev and the first pending I/O
   is posted.  If the panic behavior is desired Linux provides
   other generic methods to panic the system when threads are
   observed to hang.

*) For reference, to delay zios by 30 seconds for testing you can
   use zinject as follows: 'zinject -d <vdev> -D30 <pool>'

References:
  illumos/illumos-gate@283b84606b
  https://www.illumos.org/issues/3246

Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes 
2013-05-01 17:05:52 -07:00
Richard Yao b01615d5ac Constify structures containing function pointers
The PaX team modified the kernel's modpost to report writeable function
pointers as section mismatches because they are potential exploit
targets. We could ignore the warnings, but their presence can obscure
actual issues. Proper const correctness can also catch programming
mistakes.

Building the kernel modules against a PaX/GrSecurity patched Linux 3.4.2
kernel reports 133 section mismatches prior to this patch. This patch
eliminates 130 of them. The quantity of writeable function pointers
eliminated by constifying each structure is as follows:

vdev_opts_t             52
zil_replay_func_t       24
zio_compress_info_t     24
zio_checksum_info_t     9
space_map_ops_t         7
arc_byteswap_func_t     5

The remaining 3 writeable function pointers cannot be addressed by this
patch. 2 of them are in zpl_fs_type. The kernel's sget function requires
that this be non-const. The final writeable function pointer is created
by SPL_SHRINKER_DECLARE. The kernel's set_shrinker() and
remove_shrinker() functions also require that this be non-const.

Signed-off-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes 
2013-03-04 08:49:32 -08:00
Christopher Siden 9ae529ec5d Illumos and
2619 asynchronous destruction of ZFS file systems
2747 SPA versioning with zfs feature flags
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <gwilson@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Dan Kruchinin <dan.kruchinin@gmail.com>
Approved by: Eric Schrock <Eric.Schrock@delphix.com>

References:
  illumos/illumos-gate@53089ab7c8
  illumos/illumos-gate@ad135b5d64
  illumos changeset: 13700:2889e2596bd6
  https://www.illumos.org/issues/2619
  https://www.illumos.org/issues/2747

NOTE: The grub specific changes were not ported.  This change
must be made to the Linux grub packages.

Ported-by: Brian Behlendorf <behlendorf1@llnl.gov>
2013-01-08 10:35:35 -08:00
Etienne Dechamps 920dd524fb Add FASTWRITE algorithm for synchronous writes.
Currently, ZIL blocks are spread over vdevs using hint block pointers
managed by the ZIL commit code and passed to metaslab_alloc(). Spreading
log blocks accross vdevs is important for performance: indeed, using
mutliple disks in parallel decreases the ZIL commit latency, which is
the main performance metric for synchronous writes. However, the current
implementation suffers from the following issues:

1) It would be best if the ZIL module was not aware of such low-level
details. They should be handled by the ZIO and metaslab modules;

2) Because the hint block pointer is managed per log, simultaneous
commits from multiple logs might use the same vdevs at the same time,
which is inefficient;

3) Because dmu_write() does not honor the block pointer hint, indirect
writes are not spread.

The naive solution of rotating the metaslab rotor each time a block is
allocated for the ZIL or dmu_sync() doesn't work in practice because the
first ZIL block to be written is actually allocated during the previous
commit. Consequently, when metaslab_alloc() decides the vdev for this
block, it will do so while a bunch of other allocations are happening at
the same time (from dmu_sync() and other ZILs). This means the vdev for
this block is chosen more or less at random. When the next commit
happens, there is a high chance (especially when the number of blocks
per commit is slightly less than the number of the disks) that one disk
will have to write two blocks (with a potential seek) while other disks
are sitting idle, which defeats spreading and increases the commit
latency.

This commit introduces a new concept in the metaslab allocator:
fastwrites. Basically, each top-level vdev maintains a counter
indicating the number of synchronous writes (from dmu_sync() and the
ZIL) which have been allocated but not yet completed. When the metaslab
is called with the FASTWRITE flag, it will choose the vdev with the
least amount of pending synchronous writes. If there are multiple vdevs
with the same value, the first matching vdev (starting from the rotor)
is used. Once metaslab_alloc() has decided which vdev the block is
allocated to, it updates the fastwrite counter for this vdev.

The rationale goes like this: when an allocation is done with
FASTWRITE, it "reserves" the vdev until the data is written. Until then,
all future allocations will naturally avoid this vdev, even after a full
rotation of the rotor. As a result, pending synchronous writes at a
given point in time will be nicely spread over all vdevs. This contrasts
with the previous algorithm, which is based on the implicit assumption
that blocks are written instantaneously after they're allocated.

metaslab_fastwrite_mark() and metaslab_fastwrite_unmark() are used to
manually increase or decrease fastwrite counters, respectively. They
should be used with caution, as there is no per-BP tracking of fastwrite
information, so leaks and "double-unmarks" are possible. There is,
however, an assert in the vdev teardown code which will fire if the
fastwrite counters are not zero when the pool is exported or the vdev
removed. Note that as stated above, marking is also done implictly by
metaslab_alloc().

ZIO also got a new FASTWRITE flag; when it is used, ZIO will pass it to
the metaslab when allocating (assuming ZIO does the allocation, which is
only true in the case of dmu_sync). This flag will also trigger an
unmark when zio_done() fires.

A side-effect of the new algorithm is that when a ZIL stops being used,
its last block can stay in the pending state (allocated but not yet
written) for a long time, polluting the fastwrite counters. To avoid
that, I've implemented a somewhat crude but working solution which
unmarks these pending blocks in zil_sync(), thus guaranteeing that
linguering fastwrites will get pruned at each sync event.

The best performance improvements are observed with pools using a large
number of top-level vdevs and heavy synchronous write workflows
(especially indirect writes and concurrent writes from multiple ZILs).
Real-life testing shows a 200% to 300% performance increase with
indirect writes and various commit sizes.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue 
2012-10-17 08:56:41 -07:00
Chris Siden 1bd201e70d Illumos : zpool list should show more detailed pool info
Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Richard Lowe <richlowe@richlowe.net>
Reviewed by: Albert Lee <trisk@nexenta.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Garrett D'Amore <garrett@damore.org>
Approved by: Eric Schrock <eric.schrock@delphix.com>

References:
  https://www.illumos.org/issues/1948

Ported by:	Martin Matuska <martin@matuska.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes 
2012-09-19 13:39:05 -07:00
Brian Behlendorf 86dd0fd922 Pre-allocate vdev I/O buffers
The vdev queue layer may require a small number of buffers
when attempting to create aggregate I/O requests.  Rather than
attempting to allocate them from the global zio buffers, which
is slow under memory pressure, it makes sense to pre-allocate
them because...

1) These buffers are short lived.  They are only required for
the life of a single I/O at which point they can be used by
the next I/O.

2) The maximum number of concurrent buffers needed by a vdev is
small.  It's roughly limited by the zfs_vdev_max_pending tunable
which defaults to 10.

By keeping a small list of these buffer per-vdev we can ensure
one is always available when we need it.  This significantly
reduces contention on the vq->vq_lock, because we no longer
need to perform a slow allocation under this lock.  This is
particularly important when memory is already low on the system.

It would probably be wise to extend the use of these buffers beyond
aggregate I/O and in to the raidz implementation.  The inability
to quickly allocate buffer for the parity stripes could result in
similiar problems.

Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
2012-08-27 12:01:37 -07:00
George Wilson 5ffb9d1d05 Illumos : leaking a vdev when removing an l2cache device
1952 memory leak when adding a file-based l2arc device
1954 leak in ZFS from metaslab_group_create and zfs_ereport_checksum

Reviewed by: Adam Leventhal <ahl@delphix.com>
Reviewed by: Matt Ahrens <matt@delphix.com>
Reviewed by: Eric Schrock <eric.schrock@delphix.com>
Reviewed by: Bill Pijewski <wdp@joyent.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Approved by: Eric Schrock <eric.schrock@delphix.com>

References to Illumos issues:
  https://www.illumos.org/issues/1951
  https://www.illumos.org/issues/1952
  https://www.illumos.org/issues/1954

Ported-by: Richard Yao <ryao@cs.stonybrook.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes 
2012-04-11 11:32:06 -07:00
Brian Behlendorf 6283f55ea1 Support custom build directories and move includes
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory.  The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.

For example, this project is designed to work on various different
Linux distributions each of which work slightly differently.  This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.

Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution.  When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.

wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z

------------------------- run concurrently ----------------------
<ubuntu system>  <fedora system>  <debian system>  <rhel6 system>
mkdir ubuntu     mkdir fedora     mkdir debian     mkdir rhel6
cd ubuntu        cd fedora        cd debian        cd rhel6
../configure     ../configure     ../configure     ../configure
make             make             make             make
make check       make check       make check       make check

This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory.  This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
2010-09-08 12:38:56 -07:00