We are not allowed to dirty a filesystem when done receiving
a snapshot. In this case the flag SPA_FEATURE_LARGE_BLOCKS will
not be set on that filesystem since the filesystem is not on
dp_dirty_datasets, and a subsequent encrypted raw send will fail.
Fix this by checking in dsl_dataset_snapshot_sync_impl() if the feature
needs to be activated and do so if appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13699Closes#13782
In #13709, as in #11294 before it, it turns out that 63a26454 still had
the same failure mode as when it was first landed as d1d47691, and
fails to unlock certain datasets that formerly worked.
Rather than reverting it again, let's add handling to just throw out
the accounting metadata that failed to unlock when that happens, as
well as a test with a pre-broken pool image to ensure that we never get
bitten by this again.
Fixes: #13709
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
When scrubbing a raidz/draid pool, which contains a replacing or
sparing mirror with multiple online children, only one child will
be read. This is not normally a serious concern because the DTL
records are used to determine where a good copy of the data is.
As long as the data can be read from one child the mirror vdev
will use it to repair gaps in any of its children. Furthermore,
even if the data which was read is corrupt the raidz code will
detect this and issue its own repair I/O to correct the damage
in the mirror vdev.
However, in the scenario where the DTL is wrong due to silent
data corruption (say due to overwriting one child) and the scrub
happens to read from a child with good data, then the other damaged
mirror child will not be detected nor repaired.
While this is possible for both raidz and draid vdevs, it's most
pronounced when using draid. This is because by default the zed
will sequentially rebuild a draid pool to a distributed spare,
and the distributed spare half of the mirror is always preferred
since it delivers better performance. This means the damaged
half of the mirror will go undetected even after scrubbing.
For system administrations this behavior is non-intuitive and in
a worst case scenario could result in the only good copy of the
data being unknowingly detached from the mirror.
This change resolves the issue by reading all replacing/sparing
mirror children when scrubbing. When the BP isn't available for
verification, then compare the data buffers from each child. They
must all be identical, if not there's silent damage and an error
is returned to prompt the top-level vdev to issue a repair I/O to
rewrite the data on all of the mirror children. Since we can't
tell which child was wrong a checksum error is logged against the
replacing or sparing mirror vdev.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13555
It turns out, no, in fact, ZERO_RANGE and PUNCH_HOLE do
have differing semantics in some ways - in particular,
one requires KEEP_SIZE, and the other does not.
Also added a zero-range test to catch this, corrected a flaw
that made the punch-hole test succeed vacuously, and a typo
in file_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13329Closes#13338
When unlinking multiple files from a pool at 100% capacity, it was
possible for ENOSPC to be returned after the first unlink. e.g.
rm -f /mnt/fs/test1.0.0 /mnt/fs/test1.1.0 /mnt/fs/test1.2.0
rm: cannot remove '/mnt/fs/test1.1.0': No space left on device
rm: cannot remove '/mnt/fs/test1.2.0': No space left on device
After waiting for the pending deferred frees from the first unlink to
be processed the remaining files can then be unlinked. This is caused
by the quota limit in dsl_dir_tempreserve_impl() being temporarily
decreased to the allocatable pool capacity less any deferred free
space.
This is resolved using the existing mechanism of returning ERESTART
when over quota as long as we know enough space will shortly be
available after processing the pending deferred frees.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13172
On FreeBSD pools are not allowed to be created using vdevs which are
backed by ZFS volumes. This configuration is not recommended for any
supported platform, nevertheless the largest_pool_001_pos.ksh test
case makes use of it as a convenience. This causes the test case to
fail reliably on FreeBSD. The layout is still tolerated on Linux
so only perform this test on Linux.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13166
Raw sending from pool1/encrypted with ashift=9 to pool2/encrypted with
ashift=12 results to failure when mounting pool2/encrypted (Input/Output
error). Notably, the opposite, raw sending from a greater ashift to a
lower one does not fail.
This happens because zio_compress_write() falsely checks only
ZIO_FLAG_RAW_COMPRESS and not ZIO_FLAG_RAW_ENCRYPT which is also set in
encrypted raw send streams. In this case it rounds up the psize and if
not equal to the zio->io_size it modifies the block by zeroing out
the extra bytes. Because this happens in a SA attr. registration object
(type=46), the decryption fails upon mounting the filesystem, and zpool
status falsely reports an error.
Fix this by checking both ZIO_FLAG_RAW_COMPRESS and ZIO_FLAG_RAW_ENCRYPT
before deciding whether to zero-pad a block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13067Closes#13074
dmu_recv_begin_check() unconditionally sets the DS_HOLD_FLAG_DECRYPT
flag before calling dsl_dataset_hold_flags(). If the key on the
receiving side isn't loaded or the send stream contains embedded
blocks, the receive check fails for a stream which is perfectly
valid and could be received without any problem. This seems like
a remnant of the initial design, where unencrypted datasets below
encrypted ones weren't allowed.
Add a condition to set `DS_HOLD_FLAG_DECRYPT` only for encrypted
datasets, modify an existing test to detect this regression and add
a test for raw replication streams.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13033Closes#13076
Linux 5.16 moved XSTATE_XSAVE and XSTATE_XRESTORE out of our reach,
so add our own XSAVE{,OPT,S} code and use it for Linux 5.16.
Please note that this differs from previous behavior in that it
won't handle exceptions created by XSAVE an XRSTOR. This is sensible
for three reasons.
- Exceptions during XSAVE and XRSTOR can only occur if the feature
is not supported or enabled or the memory operand isn't aligned
on a 64 byte boundary. If this happens something else went
terribly wrong, and it may be better to stop execution.
- Previously we just printed a warning and didn't handle the fault,
this is arguable for the above reason.
- All other *SAVE instruction also don't handle exceptions, so this
at least aligns behavior.
Finally add a test to catch such a regression in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13042Closes#13059
POSIX requires that set-uid and set-gid bits to be removed when an
unprivileged user writes to a file and ZFS does that during normal
operation.
The problem arrises when the write is stored in the ZIL and replayed.
During replay we have no access to original credentials of the process
doing the write, so zfs_write() will be performed with the root
credentials. When root is doing the write set-uid and set-gid bits
are not removed from the file.
To correct that, log a separate TX_SETATTR entry that removed those bits
on first write to such file.
Idea from: Christian Schwarz
Add test for ZIL replay of setuid/setgid clearing.
Improve various edge cases when clearing setid bits:
- The setid bits can be readded during a single write, so make sure to check
for them on every chunk write.
- Log TX_SETATTR record at most once per transaction group (if the setid bits
are keep coming back).
- Move zfs_log_setattr() outside of zp->z_acl_lock.
Reviewed-by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Christian Schwarz <me@cschwarz.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13027
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
Add support for http and https to the keylocation properly to
allow encryption keys to be fetched from the specified URL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #9543Closes#9947Closes#11956
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
With the addition of functionality to rerun failing tests, some
tests that fail only sometimes still fail often enough to degrade
the reliability of the sanity runs. Remove them from the runfile
until they reliably pass.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: John Kennedy <john.kennedy@delphix.com>
Closes#12814
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12432
In l2arc_add_vdev() first decide whether the device is eligible for
L2ARC rebuild or whole device trim and then add it to the list of cache
devices. Otherwise l2arc_feed_thread() might already start writing on
the device invalidating previous content as l2ad_hand = l2ad_start.
However l2arc_rebuild_vdev() needs the device present in the cache
device list to figure out its l2arc_dev_t. Fix this by moving most of
l2arc_rebuild_vdev() in a new function l2arc_rebuild_dev() which does
not need to search in the cache device list.
In contrast to l2arc_add_vdev() we do not have to worry about
l2arc_feed_thread() invalidating previous content when onlining a
cache device. The device parameters (l2ad*) are not cleared when
offlining the device and writing new buffers will not invalidate
all previous content. In worst case only buffers that have not had
their log block written to the device will be lost.
Retire persist_l2arc_00{4,5,8} tests since they cover code already
covered by the remaining ones. Test persist_l2arc_006 is renamed to
persist_l2arc_004 and persist_l2arc_007 is renamed to persist_l2arc_005.
Fix a typo in persist_l2arc_004, and remove an assertion that is not
always true from l2arc_arcstats_pos. Also update an assertion in
persist_l2arc_005 and explain why in a comment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12365
This enables ZED to auto-online vdevs that are not wholedisk managed by
ZFS.
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Unlike most other properties the 'compatibility' property is stored
in the pool config object and not the DMU_OT_POOL_PROPS object.
This had the advantage that the compatibility information is available
without needing to fully import the pool (it can be read with zdb).
However, this means we need to make sure to update both the copy of
the config in the MOS and the cache file. This wasn't being done.
This commit adds a call to spa_async_request() to ensure the copy of
the config in the cache file gets updated as well as the one stored
in the pool. This same change is made for the 'comment' property
which suffers from the same inconsistency.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Colm Buckley <colm@tuatha.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12261Closes#12276
Update the logic to handle the dedup-case of consecutive
FREEs in the livelist code. The logic still ensures that
all the FREE entries are matched up with a respective
ALLOC by keeping a refcount for each FREE blkptr that we
encounter and ensuring that this refcount gets to zero
by the time we are done processing the livelist.
zdb -y no longer panics when encountering double frees
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11480Closes#12177
This change addresses two distinct scenarios which are possible
when performing a sequential resilver to a dRAID pool with vdevs
that contain silent unknown damage. Which in this circumstance
took the form of the devices being intentionally overwritten with
zeros. However, it could also result from a device returning incorrect
data while a sequential resilver was in progress.
Scenario 1) A sequential resilver is performed while all of the
dRAID vdevs are ONLINE and there is silent damage present on the
vdev being resilvered. In this case, nothing will be repaired
by vdev_raidz_io_done_reconstruct_known_missing() because
rc->rc_error isn't set on any of the raid columns. To address
this vdev_draid_io_start_read() has been updated to always mark
the resilvering column as ESTALE for sequential resilver IO.
Scenario 2) Multiple columns contain silent damage for the same
block and a sequential resilver is performed. In this case it's
impossible to generate the correct data from parity unless all of
the damaged columns are being sequentially resilvered (and thus
only good data is used to generate parity). This is as expected
and there's nothing which can be done about it. However, we need
to be careful not to make to situation worse. Since we can't
verify the data is actually good without a checksum, we must
only repair the devices which are being sequentially resilvered.
Otherwise, an incorrect repair to a device which previously
contained good data could effectively lock in the damage and
make reconstruction impossible. A check for this was added to
vdev_raidz_io_done_verified() along with a new test case.
Lastly, this change updates the redundancy_draid_spare1 and
redundancy_draid_spare3 test cases to be more representative
of normal dRAID replacement operation. Specifically, what we
care about is that the scrub run after a sequential resilver
does not find additional blocks which need repair. This would
indicate the sequential resilver failed to rebuild a section of
one of the devices. Note also the tests were switched to using
the verify_pool() function which still checks for checksum errors.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12061
The redundancy_draid.ksh and redundancy_raidz.ksh tests were updated
by commit 93c8e91fe to additionally verify self-healing. This
additional check increased the run time which can now occasionally
exceed the default maximum timeout in the CI environment. To prevent
this from causing failures increase the default timeout for the
redundancy test cases.
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12043
Commit d1d4769 takes into account the encryption key version to
decide if the local_mac could be zeroed out. However, this could lead
to failure mounting encrypted datasets created with intermediate
versions of ZFS encryption available in master between major releases.
In order to prevent this situation revert d1d4769 pending a more
comprehensive fix which addresses the mount failure case.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11294
Issue #12025
Issue #12300Closes#12033
When dRAID performs a normal read operation only the data columns
in the raid map are read from disk. This is enough information to
calculate the checksum, verify it, and return the needed data to the
application. It's only in the event of a checksum failure that the
additional parity and any empty columns must be read since they are
required for parity reconstruction.
Reading these additional columns is handled by vdev_raidz_read_all()
which calls vdev_draid_map_alloc_empty() to expand the raid_map_t
and submit IOs for the missing columns. This all works correctly,
but it fails to account for any "short" columns. These are data
columns which are padded with a empty skip sector at the end.
Since that empty sector is not needed for a normal read it's not
read when columns is first read from disk. However, like the parity
and empty columns the skip sector is needed to perform reconstruction.
The fix is to mark any "short" columns as never being read by clearing
the rc_tried flag when expanding the raid_map_t. This will cause
the entire column to re-read from disk in the event of a checksum
failure allowing the self-healing functionality to repair the block.
Note that this only effects the self-healing feature because when
scrubbing a pool the parity, data, and empty columns are all read
initially to verify their contents. Furthermore, only blocks which
contain "short" columns would be effected, and only when the memory
backing the skip sector wasn't already zeroed out.
This change extends the existing redundancy_raidz.ksh test case to
verify self-healing (as well as resilver and scrub). Then applies
the same test case to dRAID with a slightly modified version of
the test script called redundancy_draid.ksh. The unused variable
combrec was also removed from both test cases.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12010
A tentative implementation and discussion was done in #5285.
According to it a send --skip-missing|-s flag has been added.
In a replication stream, when there are snapshots missing in
the hierarchy, if -s is provided print a warning and ignore
dataset (and its children) instead of throwing an error
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pablo Correa Gómez <ablocorrea@hotmail.com>
Closes#11710
Just as delay zevents can flood the zevent pipe when a vdev becomes
unresponsive, so do the deadman zevents.
Ratelimit deadman zevents according to the same tunable as for delay
zevents.
Enable deadman tests on FreeBSD and add a test for deadman event
ratelimiting.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11786
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
Commit 235a85657 introduced a regression in evaluation of POSIX modes
that require group DENY entries in the internal ZFS ACL. An example
of such a POSX mode is 007. When write_implies_delete_child is set,
then ACE_WRITE_DATA is added to `wanted_dirperms` in prior to calling
zfs_zaccess_common(). This occurs is zfs_zaccess_delete().
Unfortunately, when zfs_zaccess_aces_check hits this particular DENY
ACE, zfs_groupmember() is checked to determine whether access should be
denied, and since zfs_groupmember() always returns B_TRUE on Linux and
so this check is failed, resulting ultimately in EPERM being returned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#11760
This change adds a new test that covers a bug fix in the binary search
in the redacted send resume logic that causes a kernel panic.
The bug was fixed in https://github.com/openzfs/zfs/pull/11297.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Palash Gandhi <palash.gandhi@delphix.com>
Closes#11764
Create a new section of tests to run with acltype=off.
For now the only test we have is for the DOS mode READONLY attribute on
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11734
Importing a pool using the cachefile is ideal to reduce the time
required to import a pool. However, if the devices associated with
a pool in the cachefile have changed, then the import would fail.
This can easily be corrected by doing a normal import which would
then read the pool configuration from the labels.
The goal of this change is make importing using a cachefile more
resilient and auto-correcting. This is accomplished by having
the cachefile import logic automatically fallback to reading the
labels of the devices similar to a normal import. The main difference
between the fallback logic and a normal import is that the cachefile
import logic will only look at the device directories that were
originally used when the cachefile was populated. Additionally,
the fallback logic will always import by guid to ensure that only
the pools in the cachefile would be imported.
External-issue: DLPX-71980
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#11716
When a device which is actively trimming or initializing becomes
FAULTED, and therefore no longer writable, cancel the active
TRIM or initialization. When the device is merely taken offline
with `zpool offline` then stop the operation but do not cancel it.
When the device is brought back online the operation will be
resumed if possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11588
The behavior of a NULL fromsnap was inadvertently changed for a doall
send when the send/recv logic in libzfs was updated. Restore the
previous behavior by correcting send_iterate_snap() to include all
the snapshots in the nvlist for this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Cedric Maunoury <cedric.maunoury@gmail.com>
Closes#11608
Fix regression seen in issue #11545 where checksum errors
where not being counted or showing up in a zpool event.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11609
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
While you can use zdb -R poolname vdev:offset:[<lsize>/]<psize>[:flags]
to extract individual DVAs from a vdev, it would be handy for be able
copy an entire file out of the pool.
Given a file or object number, add support to copy the contents to a
file. Useful for debugging and recovery.
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11027
When scrubbing, (non-sequential) resilvering, or correcting a checksum
error using RAIDZ parity, ZFS should heal any incorrect RAIDZ parity by
overwriting it. For example, if P disks are silently corrupted (P being
the number of failures tolerated; e.g. RAIDZ2 has P=2), `zpool scrub`
should detect and heal all the bad state on these disks, including
parity. This way if there is a subsequent failure we are fully
protected.
With RAIDZ2 or RAIDZ3, a block can have silent damage to a parity
sector, and also damage (silent or known) to a data sector. In this
case the parity should be healed but it is not.
The problem can be noticed by scrubbing the pool twice. Assuming there
was no damage concurrent with the scrubs, the first scrub should fix all
silent damage, and the second scrub should be "clean" (`zpool status`
should not report checksum errors on any disks). If the bug is
encountered, then the second scrub will repair the silently-damaged
parity that the first scrub failed to repair, and these checksum errors
will be reported after the second scrub. Since the first scrub repaired
all the damaged data, the bug can not be encountered during the second
scrub, so subsequent scrubs (more than two) are not necessary.
The root cause of the problem is some code that was inadvertently added
to `raidz_parity_verify()` by the DRAID changes. The incorrect code
causes the parity healing to be aborted if there is damaged data
(`rc_error != 0`) or the data disk is not present (`!rc_tried`). These
checks are not necessary, because we only call `raidz_parity_verify()`
if we have the correct data (which may have been reconstructed using
parity, and which was verified by the checksum).
This commit fixes the problem by removing the incorrect checks in
`raidz_parity_verify()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11489Closes#11510
Provide a basic test coverage for io_uring I/O.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11497
When removing and subsequently reattaching a vdev, CKSUM errors may
occur as vdev_indirect_read_all() reads from all children of a mirror
in case of a resilver.
Fix this by checking whether a child is missing the data and setting a
flag (ic_error) which is then checked in vdev_indirect_repair() and
suppresses incrementing the checksum counter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11277
Run zfs-tests with sanity.run for brief results. Timeouts
are rare, so minimize false positives by increasing the
default from 60 to 180 seconds.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Melikov <mail@gmelikov.ru>
Closes#11304
When running in the CI the zpool_import_012_pos test case occasionally
takes longer than the maximum 600 seconds. When this happens the test
case is considered to have failed but always completes a few minutes
latter. Since the logs suggest nothing has actually failed this commit
increases timeout and removes the exception.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11286
When sending raw encrypted datasets the user space accounting is present
when it's not expected to be. This leads to the subsequent mount failure
due a checksum error when verifying the local mac.
Fix this by clearing the OBJSET_FLAG_USERACCOUNTING_COMPLETE and reset
the local mac. This allows the user accounting to be correctly updated
on first mount using the normal upgrade process.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10523Closes#11221
`zpool create -n` fails to list cache and spare vdevs.
`zpool add -n` fails to list spare devices.
`zpool split -n` fails to list `special` and `dedup` labels.
`zpool add -n` and `zpool split -n` shouldn't list hole devices.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11122Closes#11167
Add -u option to 'zfs create' that prevents file system from being
automatically mounted. This is similar to the 'zfs receive -u'.
Authored by: pjd <pjd@FreeBSD.org>
FreeBSD-commit: freebsd/freebsd@35c58230e2
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Ported-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11254
This run file contains a subset of functional tests which exercise
as much functionality as possible while still executing relatively
quickly. The included tests should take no more than a few seconds
each to run at most. This provides a convenient way to sanity test a
change before committing to a full test run which takes several hours.
$ ./scripts/zfs-tests.sh -r sanity
...
Results Summary
PASS 813
Running Time: 00:14:42
Percent passed: 100.0%
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11271
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
George Amanakis
Rich Ercolani
Brian Behlendorf
наб
Attila Fülöp
Pawel Jakub Dawidek
Ka Ho Ng
John Wren Kennedy
Ryan Moeller
Serapheim Dimitropoulos
pablofsf
Andrea Gelmini
Andrew
Palash Gandhi
George Wilson
nssrikanth
Cedric Maunoury
Don Brady
Colm
Allan Jude
Matthew Ahrens
Matthew Macy
George Melikov
loli10K