This code should be kept inline with the upstream lua version as much
as possible. Therefore, we simply want to silence the warning. This
check was enabled by default as part of -Wall in gcc 12.1.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13528Closes#13575
The current codebase does not support raw sending buffers with block
size > 128kB when large_blocks is not active. This can happen in the
codepath dsl_dataset_sync()->dmu_objset_sync()->zio_nowait() which
calls back dmu_objset_write_done()->dsl_dataset_block_born(). If
dsl_dataset_sync() completes its run before dsl_dataset_block_born() is
called, we will end up not activating some of the necessary flags, while
having blocks based on those flags written in the filesystem. A
subsequent send will then panic.
Fix this by directly deciding in dmu_objset_sync() whether these flags
need to be activated later by dsl_dataset_sync(). Instead of panicking
due to a NULL pointer dereference in dmu_dump_write() in case of a send,
print out an error message. Also during scrub verify there are no
contradicting filesystem flags.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12275Closes#12438
Change math to make it like the ARC, using multiplications instead.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13591
- Introduce first element offset within a leaf. It allows to reduce
by ~50% average memmove() size when adding/removing elements. If the
added/removed element is in the first half of the leaf, we may shift
elements before it and adjust the bth_first instead of moving more
elements after it.
- Use memcpy() instead of memmove() when we know there is no overlap.
- Switch from uint64_t to uint32_t. It does not limit anything,
but 32-bit arches should appreciate it greatly in hot paths.
- Store leaf capacity in struct btree to avoid 64-bit divisions.
- Adjust zfs_btree_insert_into_leaf() to always result in balanced
leaves after splitting, no matter where the new element was inserted.
Not that we care about it much, but it should also allow B-trees with
as little as two elements per leaf instead of 4 previously.
When scrubbing pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks this
reduces amount of time spent in memmove() inside the scan thread from
13.7% to 5.7% and total scrub time by ~15 seconds out of 9 minutes.
It should also reduce spacemaps load time, but I haven't measured it.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13582
- Reduce size and comparison complexity of q_exts_by_size B-tree.
Previous code used two 64-bit divisions and many other operations to
compare two B-tree elements. It created enormous overhead. This
implementation moves the math to the upper level and stores the score
in the B-tree elements themselves. Since all that we need to store in
that B-tree is the extent score and offset, those can fit into single
8 byte value instead of 24 bytes of q_exts_by_addr element and can be
compared with single operation.
- Better decouple secondary tree logic from main range_tree by moving
rt_btree_ops and related functions into dsl_scan.c as ext_size_ops.
Those functions are very small to worry about the code duplication and
range_tree does not need to know details such as rt_btree_compare.
- Instead of accounting number of pending bytes per pool, that needs
atomic on global variable per block, account the number of non-empty
per-vdev queues, that change much more rarely.
- When extent scan is interrupted by TXG end, continue it in the next
TXG instead of selecting next best extent. It allows to avoid leaving
one truncated (and so likely not the best any more) extent each TXG.
On top of some other optimizations this saves about 1.5 minutes out of
10 to scrub pool of 12 SSDs, storing 1.5TB of 4KB zvol blocks.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13576
When scrubbing a raidz/draid pool, which contains a replacing or
sparing mirror with multiple online children, only one child will
be read. This is not normally a serious concern because the DTL
records are used to determine where a good copy of the data is.
As long as the data can be read from one child the mirror vdev
will use it to repair gaps in any of its children. Furthermore,
even if the data which was read is corrupt the raidz code will
detect this and issue its own repair I/O to correct the damage
in the mirror vdev.
However, in the scenario where the DTL is wrong due to silent
data corruption (say due to overwriting one child) and the scrub
happens to read from a child with good data, then the other damaged
mirror child will not be detected nor repaired.
While this is possible for both raidz and draid vdevs, it's most
pronounced when using draid. This is because by default the zed
will sequentially rebuild a draid pool to a distributed spare,
and the distributed spare half of the mirror is always preferred
since it delivers better performance. This means the damaged
half of the mirror will go undetected even after scrubbing.
For system administrations this behavior is non-intuitive and in
a worst case scenario could result in the only good copy of the
data being unknowingly detached from the mirror.
This change resolves the issue by reading all replacing/sparing
mirror children when scrubbing. When the BP isn't available for
verification, then compare the data buffers from each child. They
must all be identical, if not there's silent damage and an error
is returned to prompt the top-level vdev to issue a repair I/O to
rewrite the data on all of the mirror children. Since we can't
tell which child was wrong a checksum error is logged against the
replacing or sparing mirror vdev.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13555
The kmem_alloc(sizeof (*ctx), KM_NOSLEEP) call on FreeBSD can't be
used in this code segment. Work around this by pre-allocating a percpu
context array for later use.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Closes#13568
Handle crypto_dispatch() return values same as crp->crp_etype errors.
On FreeBSD 12 many drivers returned same errors both ways, and lack
of proper handling for the first ended up in assertion panic later.
It was changed in FreeBSD 13, but there is no reason to not be safe.
While there, skip waiting for completion, including locking and
wakeup() call, for sessions on synchronous crypto drivers, such as
typical aesni and software.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13563
Increase nlinks in stat results of ./zfs/snapshot based on snapshot
count. This provides quick and efficient method for administrators to
get snapshot counts without having to use libzfs or list the snapdir
contents.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13559
During sorted scrub multiple threads (one per vdev) are issuing many
ZIOs same time, all using the same scn->scn_zio_root ZIO as parent.
It causes huge lock contention on the single global lock on that ZIO.
Improve it by introducing per-queue null ZIOs, children to that one,
and using them instead as proxy.
For 12 SSD pool storing 1.5TB of 4KB blocks on 80-core system this
dramatically reduces lock contention and reduces scrub time from 21
minutes down to 12.5, while actual read stages (not scan) are about
3x faster, reaching 100K blocks per second per vdev.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13553
When building modules (as well as the kernel) with ARCH=um, the options
-Dsetjmp=kernel_setjmp and -Dlongjmp=kernel_longjmp are passed to the C
preprocessor for C files. This causes the setjmp and longjmp used in
module/lua/ldo.c to be kernel_setjmp and kernel_longjmp respectively in
the object file. However, the setjmp and longjmp that is intended to be
called is defined in an architecture dependent assembly file under the
directory module/lua/setjmp. Since it is an assembly and not a C file,
the preprocessor define is not given and the names do not change. This
becomes an issue when modpost is trying to create the Module.symvers
and sees no defined symbol for kernel_setjmp and kernel_longjmp. To fix
this, if the macro CONFIG_UML is defined, then setjmp and longjmp
macros are undefined.
When building with ARCH=um for x86 sub-architectures, CONFIG_X86 is not
defined. Instead, CONFIG_UML_X86 is defined. Despite this, the UML x86
sub-architecture can use the same object files as the x86 architectures
because the x86 sub-architecture UML kernel is running with the same
instruction set as CONFIG_X86. So the modules/Kbuild build file is
updated to add the same object files that CONFIG_X86 would add when
CONFIG_UML_X86 is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Glenn Washburn <development@efficientek.com>
Closes#13547
```
os/linux/zfs/zvol_os.c:1111:3: error: ignoring return value of function
declared with 'warn_unused_result' attribute [-Werror,-Wunused-result]
add_disk(zv->zv_zso->zvo_disk);
^~~~~~~~ ~~~~~~~~~~~~~~~~~~~~
zpl_xattr.c:1579:1: warning: no previous prototype for function
'zpl_posix_acl_release_impl' [-Wmissing-prototypes]
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#13551
This fd has nothing to do with cleanup, that's just the name of the
field in zfs_cmd_t that was used to pass it to the kernel.
Call it what it is, an fd for a user namespace.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13554
Since we use two B-trees q_exts_by_size and q_exts_by_addr, we should
count 2x sizeof (range_seg_gap_t) per node. And since average B-tree
memory efficiency is about 75%, we should increase it to 3x.
Previous code under-counted up to 30% of the memory usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13537
This allows ZFS datasets to be delegated to a user/mount namespace
Within that namespace, only the delegated datasets are visible
Works very similarly to Zones/Jailes on other ZFS OSes
As a user:
```
$ unshare -Um
$ zfs list
no datasets available
$ echo $$
1234
```
As root:
```
# zfs list
NAME ZONED MOUNTPOINT
containers off /containers
containers/host off /containers/host
containers/host/child off /containers/host/child
containers/host/child/gchild off /containers/host/child/gchild
containers/unpriv on /unpriv
containers/unpriv/child on /unpriv/child
containers/unpriv/child/gchild on /unpriv/child/gchild
# zfs zone /proc/1234/ns/user containers/unpriv
```
Back to the user namespace:
```
$ zfs list
NAME USED AVAIL REFER MOUNTPOINT
containers 129M 47.8G 24K /containers
containers/unpriv 128M 47.8G 24K /unpriv
containers/unpriv/child 128M 47.8G 128M /unpriv/child
```
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will.andrews@klarasystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mateusz Piotrowski <mateusz.piotrowski@klarasystems.com>
Sponsored-by: Buddy <https://buddy.works>
Closes#12263
Modern Clang and GCC can successfully implement simple conditions
without branching with math and flag operations. Use of arrays for
translation no longer helps as much as it was 14+ years ago.
Disassemble of the code generated by Clang 13.0.0 on FreeBSD 13.1,
Clang 14.0.4 on FreeBSD 14 and GCC 10.2.1 on Debian 11 with this
change still shows no branching instructions.
Profiling of CPU-bound scan stage of sorted scrub shows reproducible
reduction of time spent inside avl_find() from 6.52% to 4.58%.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13540
Add support for the kernel's block multiqueue (blk-mq) interface in
the zvol block driver. blk-mq creates multiple request queues on
different CPUs rather than having a single request queue. This can
improve zvol performance with multithreaded reads/writes.
This implementation uses the blk-mq interfaces on 4.13 or newer
kernels. Building against older kernels will fall back to the
older BIO interfaces.
Note that you must set the `zvol_use_blk_mq` module param to
enable the blk-mq API. It is disabled by default.
In addition, this commit lets the zvol blk-mq layer process whole
`struct request` IOs at a time, rather than breaking them down
into their individual BIOs. This reduces dbuf lock contention
and overhead versus the legacy zvol submit_bio() codepath.
sequential dd to one zvol, 8k volblocksize, no O_DIRECT:
legacy submit_bio() 292MB/s write 453MB/s read
this commit 453MB/s write 885MB/s read
It also introduces a new `zvol_blk_mq_chunks_per_thread` module
parameter. This parameter represents how many volblocksize'd chunks
to process per each zvol thread. It can be used to tune your zvols
for better read vs write performance (higher values favor write,
lower favor read).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#13148
Issue #12483
This commit adds BLAKE3 checksums to OpenZFS, it has similar
performance to Edon-R, but without the caveats around the latter.
Homepage of BLAKE3: https://github.com/BLAKE3-team/BLAKE3
Wikipedia: https://en.wikipedia.org/wiki/BLAKE_(hash_function)#BLAKE3
Short description of Wikipedia:
BLAKE3 is a cryptographic hash function based on Bao and BLAKE2,
created by Jack O'Connor, Jean-Philippe Aumasson, Samuel Neves, and
Zooko Wilcox-O'Hearn. It was announced on January 9, 2020, at Real
World Crypto. BLAKE3 is a single algorithm with many desirable
features (parallelism, XOF, KDF, PRF and MAC), in contrast to BLAKE
and BLAKE2, which are algorithm families with multiple variants.
BLAKE3 has a binary tree structure, so it supports a practically
unlimited degree of parallelism (both SIMD and multithreading) given
enough input. The official Rust and C implementations are
dual-licensed as public domain (CC0) and the Apache License.
Along with adding the BLAKE3 hash into the OpenZFS infrastructure a
new benchmarking file called chksum_bench was introduced. When read
it reports the speed of the available checksum functions.
On Linux: cat /proc/spl/kstat/zfs/chksum_bench
On FreeBSD: sysctl kstat.zfs.misc.chksum_bench
This is an example output of an i3-1005G1 test system with Debian 11:
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1196 1602 1761 1749 1762 1759 1751
skein-generic 546 591 608 615 619 612 616
sha256-generic 240 300 316 314 304 285 276
sha512-generic 353 441 467 476 472 467 426
blake3-generic 308 313 313 313 312 313 312
blake3-sse2 402 1289 1423 1446 1432 1458 1413
blake3-sse41 427 1470 1625 1704 1679 1607 1629
blake3-avx2 428 1920 3095 3343 3356 3318 3204
blake3-avx512 473 2687 4905 5836 5844 5643 5374
Output on Debian 5.10.0-10-amd64 system: (Ryzen 7 5800X)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1840 2458 2665 2719 2711 2723 2693
skein-generic 870 966 996 992 1003 1005 1009
sha256-generic 415 442 453 455 457 457 457
sha512-generic 608 690 711 718 719 720 721
blake3-generic 301 313 311 309 309 310 310
blake3-sse2 343 1865 2124 2188 2180 2181 2186
blake3-sse41 364 2091 2396 2509 2463 2482 2488
blake3-avx2 365 2590 4399 4971 4915 4802 4764
Output on Debian 5.10.0-9-powerpc64le system: (POWER 9)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 1213 1703 1889 1918 1957 1902 1907
skein-generic 434 492 520 522 511 525 525
sha256-generic 167 183 187 188 188 187 188
sha512-generic 186 216 222 221 225 224 224
blake3-generic 153 152 154 153 151 153 153
blake3-sse2 391 1170 1366 1406 1428 1426 1414
blake3-sse41 352 1049 1212 1174 1262 1258 1259
Output on Debian 5.10.0-11-arm64 system: (Pi400)
implementation 1k 4k 16k 64k 256k 1m 4m
edonr-generic 487 603 629 639 643 641 641
skein-generic 271 299 303 308 309 309 307
sha256-generic 117 127 128 130 130 129 130
sha512-generic 145 165 170 172 173 174 175
blake3-generic 81 29 71 89 89 89 89
blake3-sse2 112 323 368 379 380 371 374
blake3-sse41 101 315 357 368 369 364 360
Structurally, the new code is mainly split into these parts:
- 1x cross platform generic c variant: blake3_generic.c
- 4x assembly for X86-64 (SSE2, SSE4.1, AVX2, AVX512)
- 2x assembly for ARMv8 (NEON converted from SSE2)
- 2x assembly for PPC64-LE (POWER8 converted from SSE2)
- one file for switching between the implementations
Note the PPC64 assembly requires the VSX instruction set and the
kfpu_begin() / kfpu_end() calls on PowerPC were updated accordingly.
Reviewed-by: Felix Dörre <felix@dogcraft.de>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tino Reichardt <milky-zfs@mcmilk.de>
Co-authored-by: Rich Ercolani <rincebrain@gmail.com>
Closes#10058Closes#12918
It is typical, but not generally true that if log summary has more
blocks it must also have unflushed metaslabs. Normally with metaslabs
flushed in order it works, but there are known exceptions, such as
device removal or metaslab being loaded during its flush attempt.
Before 600a02b884 if spa_flush_metaslabs() hit loading metaslab it
usually stopped (unless memlimit is also exceeded), but now it may
flush more metaslabs, just skipping that particular one. This
increased chances of assertion to fire when the skipped metaslab is
flushed on next iteration if all other metaslabs in that summary
entry are already flushed out of order.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13486Closes#13513
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#13518
As of the Linux 5.19 kernel the readpage() address space operation
has been replaced by read_folio().
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 splits the secure
erase functionality from the blkdev_issue_discard() function.
The blkdev_issue_secure_erase() must now be issued to issue
a secure erase.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@44abff2c0 removed the
blk_queue_secure_erase() helper function. The preferred
interface is to now use the bdev_max_secure_erase_sectors()
function to check for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
Linux 5.19 commit torvalds/linux@70200574cc removed the
blk_queue_discard() helper function. The preferred interface
is to now use the bdev_max_discard_sectors() function to check
for discard support.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
As for the Linux 5.18 kernel bio_alloc() expects a block_device struct
as an argument. This removes the need for the bio_set_dev() compatibility
code for 5.18 and newer kernels.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13515
In current zil_commit() process, transaction lwb_tx is assigned in
zil_lwb_write_issue(), and is committed in zil_lwb_flush_vdevs_done().
Thus, during lwb write out process, the txg is held in open or quiesing
state, until zil_lwb_flush_vdevs_done() is called. If the zil's zio
latency is high, it will cause txg_sync_thread() to starve.
The goal here is to defer waiting for zil_lwb_flush_vdevs_done to the
'syncing' txg state. That is, in zil_sync().
In this patch, it achieves the goal without holding transaction.
A new function zil_lwb_flush_wait_all() is introduced. It waits for
the completion of all the zil_lwb_flush_vdevs_done() by given txg.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12321
- Make prefetch distance adaptive: up to 4MB prefetch doubles for
every, hit same as before, but after that it grows by 1/8 every time
the prefetch read does not complete in time to satisfy the demand.
My tests show that 4MB is sufficient for wide NVMe pool to saturate
single reader thread at 2.5GB/s, while new 64MB maximum allows the
same thread to reach 1.5GB/s on wide HDD pool. Further distance
increase may increase speed even more, but less dramatic and with
higher latency.
- Allow early reuse of inactive prefetch streams: streams that never
saw hits can be reused immediately if there is a demand, while others
can be reused after 1s of inactivity, starting with the oldest. After
2s of inactivity streams are deleted to free resources same as before.
This allows by several times increase strided read performance on HDD
pool in presence of simultaneous random reads, previously filling the
zfetch_max_streams limit for seconds and so blocking most of prefetch.
- Always issue intermediate indirect block reads with SYNC priority.
Each of those reads if delayed for longer may delay up to 1024 other
block prefetches, that may be not good for wide pools.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13452
This issue was discovered by zloop runs. When a mirror or other
redundant top-level vdev has a disk failure, and the disk is replaced,
the rebuild process occurs. A removal can happen while this is in
progress. If the removal completes before the rebuild does, the
removal process will try to free the vdev that is still in use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#13498
Original Log Size Limit implementation blocked all writes in case of
limit reached until the TXG is committed and the log is freed. It
caused huge delays and following speed spikes in application writes.
This implementation instead smoothly throttles writes, using exactly
the same mechanism as used for dirty data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: jxdking <lostking2008@hotmail.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Issue #12284Closes#13476
It turns out that "do LZ4 and zstd-1 both fail" is a great heuristic
for "don't even bother trying higher zstd tiers".
By way of illustration:
$ cat /incompress | mbuffer | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_normal
summary: 39.8 GiByte in 3min 40.2sec - average of 185 MiB/s
$ echo 3 | sudo tee /sys/module/zzstd/parameters/zstd_lz4_pass
3
$ cat /incompress | mbuffer -m 4G | zfs recv -o compression=zstd-12 evenfaster/lowcomp_1M_zstd12_patched
summary: 39.8 GiByte in 48.6sec - average of 839 MiB/s
$ sudo zfs list -p -o name,used,lused,ratio evenfaster/lowcomp_1M_zstd12_normal evenfaster/lowcomp_1M_zstd12_patched
NAME USED LUSED RATIO
evenfaster/lowcomp_1M_zstd12_normal 39549931520 42721221632 1.08
evenfaster/lowcomp_1M_zstd12_patched 39626399744 42721217536 1.07
$ python3 -c "print(39626399744 - 39549931520)"
76468224
$
I'll take 76 MB out of 42 GB for > 4x speedup.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13244
We want `zpool import` to be highly robust and never panic, even
when encountering corrupt metadata. This is already handled in the
arc_read() code path, which covers most cases, but spa_load_verify_cb()
relies on zio_read() and is responsible for verifying the block pointer.
During import it is also possible to encounter blocks pointers which
contain ZIO_COMPRESS_INHERIT and ZIO_CHECKSUM_INHERIT values. Relax
the verification function slightly to allow this.
Futhermore, extend dsl_scan_recurse() to verify the block pointer
contents of level zero blocks which are not of type DMU_OT_DNODE or
DMU_OT_OBJSET. This is handled by arc_read() in the other cases.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13124Closes#13360
There are times when end-users may wish to have
a fast and convenient method to get zpool guid
without having to use libzfs. This commit
exposes the zpool guid via kstats in similar
manner to the zpool state.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13466
Recognise initial whitespace, + in both cases,
and - also in unsigneds
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13434
Linux passes -Wframe-larger-than=1024, which breaks
our build in a number of places with -Werror.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13450
Refcount creation for abd_zero_scatter->abd_children is redundant in
abd_alloc_zero_scatter, as it has been done in abd_init_struct.
In addition, abd_children is undefined when ZFS_DEBUG is disabled, the
reference of abd_children in abd_alloc_zero_scatter breaks build of
libzpool when ZFS_DEBUG is disabled.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13429
clang-15 emits the following error message for functions without
a prototype:
fs/zfs/os/linux/spl/spl-kmem-cache.c:1423:27: error:
a function declaration without a prototype is deprecated
in all versions of C [-Werror,-Wstrict-prototypes]
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Aidan Harris <me@aidanharr.is>
Closes#13421
I genuinely don't know why this didn't come up before,
but adding the LZ4 early abort pointed out this flaw,
in which we're allocating a buffer of one size, and
then telling the compressor that we're handing it buffers
of a different size, which may be Very Different - say,
allocating 512b and then telling it the inputs are 128k.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13375
When calculating mg_aliquot alike to #12046 use number of unique data
disks in the vdev, not the total number of children vdev. Increase
default value of the tunable from 512KB to 1MB to compensate.
Before this change each disk in striped pool was getting 512KB of
sequential data, in 2-wide mirror -- 1MB, in 3-wide RAIDZ1 -- 768KB.
After this change in all the cases each disk should get 1MB.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#13388
Holding a dbuf is a common operation which can become highly contended
in dbuf_find() when acquiring the dbuf hash mutex. This is particularly
true on Linux when reading/writing volumes since by default up to 32
threads from the zvol_taskq may be taking a hold of the same dbuf.
This should also be observable on FreeBSD as long as there are enough
processes accessing the volume concurrently.
This is further aggregrated by the fact that only the block id will
be unique when calculating the dbuf hash for a single volume. The
objset id, object id, and level will be the same for data blocks.
This has been observed to result in a somehwat less than uniform hash
distribution and a longer than expected max hash chain depth (~20)
on a large memory system (256 GB) using volumes.
This commit improves the siutation by switching the hash mutex to
an rwlock to allow concurrent lookups, and increasing DBUF_RWLOCKS
from 2048 to 8192 to further reduce the odds of a hash collision.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13405
Page writebacks with WB_SYNC_NONE can take several seconds to complete
since they wait for the transaction group to close before being
committed. This is usually not a problem since the caller does not
need to wait. However, if we're simultaneously doing a writeback
with WB_SYNC_ALL (e.g via msync), the latter can block for several
seconds (up to zfs_txg_timeout) due to the active WB_SYNC_NONE
writeback since it needs to wait for the transaction to complete
and the PG_writeback bit to be cleared.
This commit deals with 2 cases:
- No page writeback is active. A WB_SYNC_ALL page writeback starts
and even completes. But when it's about to check if the PG_writeback
bit has been cleared, another writeback with WB_SYNC_NONE starts.
The sync page writeback ends up waiting for the non-sync page
writeback to complete.
- A page writeback with WB_SYNC_NONE is already active when a
WB_SYNC_ALL writeback starts. The WB_SYNC_ALL writeback ends up
waiting for the WB_SYNC_NONE writeback.
The fix works by carefully keeping track of active sync/non-sync
writebacks and committing when beneficial.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Shaan Nobee <sniper111@gmail.com>
Closes#12662Closes#12790
- Prefer O_* flags over F* flags that mostly mirror O_* flags anyway,
but O_* flags seem to be preferred.
- Simplify the code as all the F*SYNC flags were defined as FFSYNC flag.
- Don't define FRSYNC flag, so we don't generate unnecessary ZIL commits.
- Remove EXCL define, FreeBSD ignores the excl argument for zfs_create()
anyway.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13400
Commit 361a7e8 (log xattr=sa create/remove/update to ZIL) introduced a
TX_SETSAXATTR, but missed to add a corresponding entry in
zvol_replay_vector. Adding a missing replay entry in zvol_replay_vector.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#13396Closes#13395
Clang 13.0.0 added support for `Wunused-but-set-parameter` and
`-Wunused-but-set-variable` which correctly detects two unused
variables in zstd resulting in a build failure. This commit
annotates these instances accordingly.
https://releases.llvm.org/13.0.1/tools/clang/docs/ReleaseNotes.html#id6
In FSE_createCTable(), malloc() is intentionally defined as NULL when
compiled in the kernel so the variable is unused.
zstd/lib/compress/fse_compress.c:307:12: error: variable 'size'
set but not used [-Werror,-Wunused-but-set-variable]
Additionally, in ZSTD_seqDecompressedSize() the assert is compiled
out similarly resulting in an unused variable.
zstd/lib/compress/zstd_compress_superblock.c:412:12: error: variable
'litLengthSum' set but not used [-Werror,-Wunused-but-set-variable]
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13382
Increase the default allowed maximum recordsize from 1M to 16M.
As described in the zfs(4) man page, there are significant costs
which need to be considered before using very large blocks.
However, there are scenarios where they make good sense and
it should no longer be necessary to artificially restrict their
use behind a module option.
Note that for 32-bit platforms we continue to leave this
restriction in place due to the limited virtual address space
available (256-512MB). On these systems only a handful
of blocks could be cached at any one time severely impacting
performance and potentially stability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12830Closes#13302
When using a Linux kernel which predates the iov_iter interface the
O_APPEND flag should be applied in zpl_aio_write() via the call to
generic_write_checks(). The updated pos variable was incorrectly
ignored resulting in the current offset being used.
This issue should only realistically impact the RHEL/CentOS 7.x
kernels which are based on Linux 3.10.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13370Closes#13377
Linux 5.12 PPC 5.12 get_user() and __copy_from_user_inatomic()
inline helpers very indirectly include a reference to the GPL'd
array mmu_feature_keys[] and fails to build. Workaround this by
using copy_from_user() and throwing EFAULT for any calls to
__copy_from_user_inatomic(). This is a workaround until a fix
for Linux commit 7613f5a66becfd0e43a0f34de8518695888f5458
"powerpc/64s/kuap: Use mmu_has_feature()" is fully addressed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#11958Closes#12590Closes#13367
Previous flushing algorithm limited only total number of log blocks to
the minimum of 256K and 4x number of metaslabs in the pool. As result,
system with 1500 disks with 1000 metaslabs each, touching several new
metaslabs each TXG could grow spacemap log to huge size without much
benefits. We've observed one of such systems importing pool for about
45 minutes.
This patch improves the situation from five sides:
- By limiting maximum period for each metaslab to be flushed to 1000
TXGs, that effectively limits maximum number of per-TXG spacemap logs
to load to the same number.
- By making flushing more smooth via accounting number of metaslabs
that were touched after the last flush and actually need another flush,
not just ms_unflushed_txg bump.
- By applying zfs_unflushed_log_block_pct to the number of metaslabs
that were touched after the last flush, not all metaslabs in the pool.
- By aggressively prefetching per-TXG spacemap logs up to 16 TXGs in
advance, making log spacemap load process for wide HDD pool CPU-bound,
accelerating it by many times.
- By reducing zfs_unflushed_log_block_max from 256K to 128K, reducing
single-threaded by nature log processing time from ~10 to ~5 minutes.
As further optimization we could skip bumping ms_unflushed_txg for
metaslabs not touched since the last flush, but that would be an
incompatible change, requiring new pool feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12789
Currently, determining which datasets are affected by corruption is
a manual process.
The primary difficulty in reporting the list of affected snapshots is
that since the error was initially found, the snapshot where the error
originally occurred in, may have been deleted. To solve this issue, we
add the ID of the head dataset of the original snapshot which the error
was detected in, to the stored error report. Then any time a filesystem
is deleted, the errors associated with it are deleted as well. Any time
a clone promote occurs, we modify reports associated with the original
head to refer to the new head. The stored error reports are identified
by this head ID, the birth time of the block which the error occurred
in, as well as some information about the error itself are also stored.
Once this information is stored, we can find the set of datasets
affected by an error by walking back the list of snapshots in the given
head until we find one with the appropriate birth txg, and then traverse
through the snapshots of the clone family, terminating a branch if the
block was replaced in a given snapshot. Then we report this information
back to libzfs, and to the zpool status command, where it is displayed
as follows:
pool: test
state: ONLINE
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: https://openzfs.github.io/openzfs-docs/msg/ZFS-8000-8A
scan: scrub repaired 0B in 00:00:00 with 800 errors on Fri Dec 3
08:27:57 2021
config:
NAME STATE READ WRITE CKSUM
test ONLINE 0 0 0
sdb ONLINE 0 0 1.58K
errors: Permanent errors have been detected in the following files:
test@1:/test.0.0
/test/test.0.0
/test/1clone/test.0.0
A new feature flag is introduced to mark the presence of this change, as
well as promotion and backwards compatibility logic. This is an updated
version of #9175. Rebase required fixing the tests, updating the ABI of
libzfs, updating the man pages, fixing bugs, fixing the error returns,
and updating the old on-disk error logs to the new format when
activating the feature.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Co-authored-by: TulsiJain <tulsi.jain@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#9175Closes#12812
It turns out, no, in fact, ZERO_RANGE and PUNCH_HOLE do
have differing semantics in some ways - in particular,
one requires KEEP_SIZE, and the other does not.
Also added a zero-range test to catch this, corrected a flaw
that made the punch-hole test succeed vacuously, and a typo
in file_write.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13329Closes#13338
In hypothetical case of non-linear ABD with single segment, multiple
to page size but not aligned to it, vdev_geom_fill_unmap_cb() could
fill one page less into bio_ma array.
I am not sure it is exploitable, but better to be safe than sorry.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Mark Johnston <markj@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13345
This can be reverted once we're sure nobody's using them anymore
(post-3.0 release?)
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
Originally it was thought it would be useful to split up the kmods
by functionality. This would allow external consumers to only load
what was needed. However, in practice we've never had a case where
this functionality would be needed, and conversely managing multiple
kmods can be awkward. Therefore, this change merges all but the
spl.ko kmod in to a single zfs.ko kmod.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13274
These are displayed as the descriptions of the sysctl's on FreeBSD
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#13334
As of the 5.17 kernel the GENHD_FL_EXT_DEVT flag has been removed
and the GENHD_FL_NO_PART_SCAN flag renamed GENHD_FL_NO_PART. Update
zvol_alloc() to set GENHD_FL_NO_PART for the newer kernels which
is sufficient. The behavior for prior kernels remains unchanged.
1ebe2e5f ("block: remove GENHD_FL_EXT_DEVT")
46e7eac6 ("block: rename GENHD_FL_NO_PART_SCAN to GENHD_FL_NO_PART")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13294Closes#13297
FreeBSD's memory management system uses its own error numbers and gets
confused when these VOPs return EIO.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reported-by: Peter Holm <pho@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
For legacy reasons, a couple of VOPs have to return error numbers that
don't come from the usual errno namespace. To handle the cases where
ZFS_ENTER or ZFS_VERIFY_ZP fail, we need to be able to override the
default error return value of EIO. Extend the macros to permit this.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#13311
An earlier commit introduces AT_MODE into the shared kernel sources,
instead of the preferred existing ATTR_MODE use.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Jorgen lundman <lundman@lundman.net>
Closes#13293
I got the status backward (B_FALSE for fixed, rather than B_TRUE for
flex); before:
$ zfs get mountpoint tarta-zoot -r
NAME PROPERTY VALUE SOURCE
tarta-zoot mountpoint / local
tarta-zoot/PAGEFILE.SYS mountpoint - -
tarta-zoot/etc mountpoint /etc inherited from tarta-zoot
tarta-zoot/home mountpoint /home inherited from tarta-zoot
tarta-zoot/home/xspon mountpoint /home/xspon inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli mountpoint /home/nabijaczleweli inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli/tftp mountpoint /home/nabijaczleweli/tftp inherited from tarta-zoot
tarta-zoot/home/root mountpoint /root local
after:
$ zfs get mountpoint tarta-zoot -r
NAME PROPERTY VALUE SOURCE
tarta-zoot mountpoint / local
tarta-zoot/PAGEFILE.SYS mountpoint - -
tarta-zoot/etc mountpoint /etc inherited from tarta-zoot
tarta-zoot/home mountpoint /home inherited from tarta-zoot
tarta-zoot/home/xspon mountpoint /home/xspon inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli mountpoint /home/nabijaczleweli inherited from tarta-zoot
tarta-zoot/home/nabijaczleweli/tftp mountpoint /home/nabijaczleweli/tftp inherited from tarta-zoot
tarta-zoot/home/root mountpoint /root local
Fixes: be8e1d81bf ("Flex
non-pretty-printed properties and raw-/pretty-print remaining ones")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13286
->readpages was removed and replaced by ->readahead. Define
zpl_readahead for kernels that don't have ->readpages.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Riccardo Schirone <rschirone91@gmail.com>
Closes#13278
NDF_ONLY_PNBUF has been removed from FreeBSD in favor of NDFREE_PNBUF.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13277
Bypass check of ZFS aces if the ACL is trivial. When an ACL is
trivial its permissions are represented by the mode without any
loss of information. In this case, it is safe to convert the
access request into equivalent mode and then pass desired mask
and inode to generic_permission(). This has the added benefit
of also checking whether entries in a POSIX ACL on the file grant
the desired access.
This commit also skips the ACL check on looking up the xattr dir
since such restrictions don't exist in Linux kernel and it makes
xattr lookup behavior inconsistent between SA and file-based
xattrs. We also don't want to perform a POSIX ACL check while
looking up the POSIX ACL if for some reason it is located in
the xattr dir rather than an SA.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#13237
The argument type of rw_destroy is (krwlock_t *) while currently
krwlock_t is passed in zfs_ctldir.c. This error is hidden because
rw_destroy is defined as ((void) 0) in linux. But anyway, this
mismatch should be fixed.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13272
When HAVE_BLKDEV_GET_ERESTARTSYS is defined, compiler will complain
"defined but not used" warning for zvol_open_timeout_ms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ping Huang <huangping@smartx.com>
Closes#13270
blkdev.h includes genhd.h since dawn of upstream git, so this is
globally safe
Upstream-commit: 322cbb50de711814c42fb088f6d31901502c711a ("block:
remove genhd.h")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
bio_alloc(gfp_t gfp_mask, unsigned short nr_iovecs)
became
bio_alloc(struct block_device *bdev, unsigned short nr_vecs,
unsigned int opf, gfp_t gfp_mask)
passing NULL/0 continues previous behaviour
Upstream-commit: 07888c665b405b1cd3577ddebfeb74f4717a84c4 ("block:
pass a block_device and opf to bio_alloc")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13251
Parts of the Linux kernel build system struggle with _Noreturn. This
results in the following warnings when building on RHEL 8.5, and likely
other environments. Switch to using the __attribute__((noreturn)).
warning: objtool: dbuf_free_range()+0x2b8:
return with modified stack frame
warning: objtool: dbuf_free_range()+0x0:
stack state mismatch: cfa1=7+40 cfa2=7+8
...
WARNING: EXPORT symbol "arc_buf_size" [zfs.ko] version generation
failed, symbol will not be versioned.
WARNING: EXPORT symbol "spa_open" [zfs.ko] version generation
failed, symbol will not be versioned.
...
Additionally, __thread_exit() has been renamed spl_thread_exit() and
made a static inline function. This was needed because the kernel
will generate a warning for symbols which are __attribute__((noreturn))
and then exported with EXPORT_SYMBOL.
While we could continue to use _Noreturn in user space I've also
switched it to __attribute__((noreturn)) purely for consistency
throughout the code base.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13238
This explodes as -Wunused-variable on GCC 8.5.0, despite it being used,
just not in an evaluated context
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13195
This PR changes ZFS ACL checks to evaluate
fsuid / fsgid rather than euid / egid to avoid
accidentally granting elevated permissions to
NFS clients.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Andrew Walker <awalker@ixsystems.com>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#13221
At shutdown time, we drain all of the zevents and set the
ZEVENT_SHUTDOWN flag. On FreeBSD, we may end up calling
zfs_zevent_destroy() after the zevent_lock has been destroyed while
the sysevent thread is winding down; we observe ESHUTDOWN, then back
out.
Events have already been drained, so just inline the kmem_free call in
sysevent_worker() to avoid the race, and document the assumption that
zfs_zevent_destroy doesn't do anything else useful at that point.
This fixes a panic that can occur at module unload time.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#13220
bcopy() has a confusing argument order and is actually a move, not a
copy; they're all deprecated since POSIX.1-2001 and removed in -2008,
and we shim them out to mem*() on Linux anyway
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12996
On some architectures ZERO_PAGE is unavailable because it references
a GPL exported symbol of empty_zero_page. Originally e08b993 removed
the call to PAGE_ZERO(0) for assignment to the abd_zero_page. However,
a simple check can be done to avoid a kernel allocation and free for
the abd_zero_page if ZERO_PAGE is available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#13199
Caught by UBSAN: ZI_NO_DVA is passed explicitly in
zio_handle_decrypt_injection() and can be an ENOENT from zio_match_dva()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13146Closes#13190
Add physical device size/capacity only for physical devices in
'zpool list -v' instead of displaying "-" in the SIZE column.
This would make it easier to see the individual device capacity and
to determine which spares are large enough to replace which devices.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Dipak Ghosh <dipak.ghosh@hpe.com>
Signed-off-by: Akash B <akash-b@hpe.com>
Closes#12561Closes#13106
Cleanup the kernel SIMD code by removing kernel dependencies.
- Replace XSTATE_XSAVE with our own XSAVE implementation for all
kernels not exporting kernel_fpu{begin,end}(), see #13059
- Replace union fpregs_state by a uint8_t * buffer and get the size
of the buffer from the hardware via the CPUID instruction
- Replace kernels xgetbv() by our own implementation which was
already there for userspace.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13102
When unlinking multiple files from a pool at 100% capacity, it was
possible for ENOSPC to be returned after the first unlink. e.g.
rm -f /mnt/fs/test1.0.0 /mnt/fs/test1.1.0 /mnt/fs/test1.2.0
rm: cannot remove '/mnt/fs/test1.1.0': No space left on device
rm: cannot remove '/mnt/fs/test1.2.0': No space left on device
After waiting for the pending deferred frees from the first unlink to
be processed the remaining files can then be unlinked. This is caused
by the quota limit in dsl_dir_tempreserve_impl() being temporarily
decreased to the allocatable pool capacity less any deferred free
space.
This is resolved using the existing mechanism of returning ERESTART
when over quota as long as we know enough space will shortly be
available after processing the pending deferred frees.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#13172
ZFS allows to update and retrieve additional file level attributes for
FreeBSD. This commit allows additional file level attributes to be
updated and retrieved for Linux. These include the flags stored in the
upper half of z_pflags only.
Two new IOCTLs have been added for this purpose. ZFS_IOC_GETDOSFLAGS
can be used to retrieve the attributes, while ZFS_IOC_SETDOSFLAGS can
be used to update the attributes.
Attributes that are allowed to be updated include ZFS_IMMUTABLE,
ZFS_APPENDONLY, ZFS_NOUNLINK, ZFS_ARCHIVE, ZFS_NODUMP, ZFS_SYSTEM,
ZFS_HIDDEN, ZFS_READONLY, ZFS_REPARSE, ZFS_OFFLINE and ZFS_SPARSE.
Flags can be or'd together while calling ZFS_IOC_SETDOSFLAGS.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Umer Saleem <usaleem@ixsystems.com>
Closes#13118
A function that returns with no value is a different thing from a
function that doesn't return at all. Those are two orthogonal
concepts, commonly confused.
pthread_create(3) expects a pointer to a start routine that has a
very precise prototype:
void *(*start_routine)(void *);
However, other thread functions, such as kernel ones, expect:
void (*start_routine)(void *);
Providing a different one is incorrect, and has only been working
because the ABIs happen to produce a compatible function.
We should use '_Noreturn void', since it's the natural type, and
then provide a '_Noreturn void *' wrapper for pthread functions.
For consistency, replace most cases of __NORETURN or
__attribute__((noreturn)) by _Noreturn. _Noreturn is understood
by -std=gnu89, so it should be safe to use everywhere.
Ref: https://github.com/openzfs/zfs/pull/13110#discussion_r808450136
Ref: https://software.codidact.com/posts/285972
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alejandro Colomar <alx.manpages@gmail.com>
Closes#13120
Before this, /all/ numerical properties 1 (ZFS_PROP_CREATION,
ZPOOL_PROP_SIZE, VDEV_PROP_CAPACITY) would be non-fixed and
/all/ numerical properties 5 (ZFS_PROP_COMPRESSRATIO,
ZPOOL_PROP_HEALTH, VDEV_PROP_PSIZE) would be 8-wide
Realistically, this doesn't appear to be much of a problem
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13125
It's much nicer to import from upstream this way, and compiles
faster too.
Everything in lib/ is unmodified 1.4.5.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12978
As such, there are no specific synchronous semantics defined for
the xattrs. But for xattr=on, it does log to ZIL and zil_commit() is
done, if sync=always is set on dataset. This provides sync semantics
for xattr=on with sync=always set on dataset.
For the xattr=sa implementation, it doesn't log to ZIL, so, even with
sync=always, xattrs are not guaranteed to be synced before xattr call
returns to caller. So, xattr can be lost if system crash happens, before
txg carrying xattr transaction is synced.
This change adds xattr=sa logging to ZIL on xattr create/remove/update
and xattrs are synced to ZIL (zil_commit() done) for sync=always.
This makes xattr=sa behavior similar to xattr=on.
Implementation notes:
The actual logging is fairly straight-forward and does not warrant
additional explanation.
However, it has been 14 years since we last added new TX types
to the ZIL [1], hence this is the first time we do it after the
introduction of zpool features. Therefore, here is an overview of the
feature activation and deactivation workflow:
1. The feature must be enabled. Otherwise, we don't log the new
record type. This ensures compatibility with older software.
2. The feature is activated per-dataset, since the ZIL is per-dataset.
3. If the feature is enabled and dataset is not for zvol, any append to
the ZIL chain will activate the feature for the dataset. Likewise
for starting a new ZIL chain.
4. A dataset that doesn't have a ZIL chain has the feature deactivated.
We ensure (3) by activating on the first zil_commit() after the feature
was enabled. Since activating the features requires waiting for txg
sync, the first zil_commit() after enabling the feature will be slower
than usual. The downside is that this is really a conservative
approximation: even if we never append a 'TX_SETSAXATTR' to the ZIL
chain, we pay the penalty for feature activation. The upside is that the
user is in control of when we pay the penalty, i.e., upon enabling the
feature.
We ensure (4) by hooking into zil_sync(), where ZIL destroy actually
happens.
One more piece on feature activation, since it's spread across
multiple functions:
zil_commit()
zil_process_commit_list()
if lwb == NULL // first zil_commit since zil_open
zil_create()
if no log block pointer in ZIL header:
if feature enabled and not active:
// CASE 1
enable, COALESCE txg wait with dmu_tx that allocated the
log block
else // log block was allocated earlier than this zil_open
if feature enabled and not active:
// CASE 2
enable, EXPLICIT txg wait
else // already have an in-DRAM LWB
if feature enabled and not active:
// this happens when we enable the feature after zil_create
// CASE 3
enable, EXPLICIT txg wait
[1] da6c28aaf6
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#8768Closes#9078
New `zfs_type_t` value `ZFS_TYPE_INVALID` is introduced.
Variable initialization is now possible to make GCC happy.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12167Closes#13103
The default behavior where the serious ZFS errors cause FS thread to
stuck is very bad for some production scenario.
In some production scenarios (Linux), it is recommended to make real
kernel PANIC, where system can be rebooted by watchdog or kernel itself.
This patch enables coherent handling of spl_panic_halt parameter.
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Authored-by: Wojciech Nizinski <w.nizinski@grinn-global.com>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12120Closes#13109
Which produces a warning since uints are, by definition, >=0
Reviewed-by: Alejandro Colomar <alx.manpages@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#13110
Raw sending from pool1/encrypted with ashift=9 to pool2/encrypted with
ashift=12 results to failure when mounting pool2/encrypted (Input/Output
error). Notably, the opposite, raw sending from a greater ashift to a
lower one does not fail.
This happens because zio_compress_write() falsely checks only
ZIO_FLAG_RAW_COMPRESS and not ZIO_FLAG_RAW_ENCRYPT which is also set in
encrypted raw send streams. In this case it rounds up the psize and if
not equal to the zio->io_size it modifies the block by zeroing out
the extra bytes. Because this happens in a SA attr. registration object
(type=46), the decryption fails upon mounting the filesystem, and zpool
status falsely reports an error.
Fix this by checking both ZIO_FLAG_RAW_COMPRESS and ZIO_FLAG_RAW_ENCRYPT
before deciding whether to zero-pad a block.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#13067Closes#13074
ZFS on Linux originally implemented xattr namespaces in a way that is
incompatible with other operating systems. On illumos, xattrs do not
have namespaces. Every xattr name is visible. FreeBSD has two
universally defined namespaces: EXTATTR_NAMESPACE_USER and
EXTATTR_NAMESPACE_SYSTEM. The system namespace is used for protected
FreeBSD-specific attributes such as MAC labels and pnfs state. These
attributes have the namespace string "freebsd:system:" prefixed to the
name in the encoding scheme used by ZFS. The user namespace is used
for general purpose user attributes and obeys normal access control
mechanisms. These attributes have no namespace string prefixed, so
xattrs written on illumos are accessible in the user namespace on
FreeBSD, and xattrs written to the user namespace on FreeBSD are
accessible by the same name on illumos.
Linux has several xattr namespaces. On Linux, ZFS encodes the
namespace in the xattr name for every namespace, including the user
namespace. As a consequence, an xattr in the user namespace with the
name "foo" is stored by ZFS with the name "user.foo" and therefore
appears on FreeBSD and illumos to have the name "user.foo" rather than
"foo". Conversely, none of the xattrs written on FreeBSD or illumos
are accessible on Linux unless the name happens to be prefixed with one
of the Linux xattr namespaces, in which case the namespace is stripped
from the name. This makes xattrs entirely incompatible between Linux
and other platforms.
We want to make the encoding of user namespace xattrs compatible across
platforms. A critical requirement of this compatibility is for xattrs
from existing pools from FreeBSD and illumos to be accessible by the
same names in the user namespace on Linux. It is also necessary that
existing pools with xattrs written by Linux retain access to those
xattrs by the same names on Linux. Making user namespace xattrs from
Linux accessible by the correct names on other platforms is important.
The handling of other namespaces is not required to be consistent.
Add a fallback mechanism for listing and getting xattrs to treat xattrs
as being in the user namespace if they do not match a known prefix.
Do not allow setting or getting xattrs with a name that is prefixed
with one of the namespace names used by ZFS on supported platforms.
Allow choosing between legacy illumos and FreeBSD compatibility and
legacy Linux compatibility with a new tunable. This facilitates
replication and migration of pools between hosts with different
compatibility needs.
The tunable controls whether or not to prefix the namespace to the
name. If the xattr is already present with the alternate prefix,
remove it so only the new version persists. By default the platform's
existing convention is used.
Reviewed-by: Christian Schwarz <christian.schwarz@nutanix.com>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11919
These were all folded into a single kstat at
/proc/spl/kstat/kcf/NONAME_provider_stats
with no way to know which one it actually was,
and only the AES and SHA (so not Skein) ones were ever updated
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
They don't do anything except clogging up the AVL tree
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
It's the only one actually used
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
It only needs to be locked if dynamic changes can occur. They can't.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
We register all providers at once, before anything happens
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
This is currently twice the amount we actually have (sha[12], skein,
aes), and 512 * sizeof(void*) = 4096: 128x more than we need and a waste
of most of a page in the kernel address space
Plus, there's no need to actually allocate it dynamically: it's always
got a static size. Put it in .data
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12901
Add hooks for when spa is created, exported, activated and
deactivated. Used by macOS to attach iokit, and lock
kext as busy (to stop unloads).
Userland, Linux, and, FreeBSD have empty stubs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12801
There are two codepaths than can dirty final TXGs:
1) If calling spa_export_common()->spa_unload()->
spa_unload_log_sm_flush_all() after the spa_final_txg is set, then
spa_sync()->spa_flush_metaslabs() may end up dirtying the final
TXGs. Then we have the following panic:
Call Trace:
<TASK>
dump_stack_lvl+0x46/0x62
spl_panic+0xea/0x102 [spl]
dbuf_dirty+0xcd6/0x11b0 [zfs]
zap_lockdir_impl+0x321/0x590 [zfs]
zap_lockdir+0xed/0x150 [zfs]
zap_update+0x69/0x250 [zfs]
feature_sync+0x5f/0x190 [zfs]
space_map_alloc+0x83/0xc0 [zfs]
spa_generate_syncing_log_sm+0x10b/0x2f0 [zfs]
spa_flush_metaslabs+0xb2/0x350 [zfs]
spa_sync_iterate_to_convergence+0x15a/0x320 [zfs]
spa_sync+0x2e0/0x840 [zfs]
txg_sync_thread+0x2b1/0x3f0 [zfs]
thread_generic_wrapper+0x62/0xa0 [spl]
kthread+0x127/0x150
ret_from_fork+0x22/0x30
</TASK>
2) Calling vdev_*_stop_all() for a second time in spa_unload() after
spa_export_common() unnecessarily delays the final TXGs beyond what
spa_final_txg is set at.
Fix this by performing the check and call for
spa_unload_log_sm_flush_all() before the spa_final_txg is set in
spa_export_common(). Also check if the spa_final_txg has already been
set in spa_unload() and skip those calls in this case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
External-issue: https://www.illumos.org/issues/9081Closes#13048Closes#13098
Unfortunately macOS has obj-C keyword "fallthrough" in the OS headers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#13097
On newer compilers, dsl_dataset.c now warns (or, on DEBUG, errors)
on uninitialized variable usage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#13083
This allows reads/writes caused by accesses to mmap files to be
accounted correctly in the per-dataset kstats for both Linux and
FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matthias Blankertz <matthias@blankertz.org>
Closes#12994Closes#13044
dmu_recv_begin_check() unconditionally sets the DS_HOLD_FLAG_DECRYPT
flag before calling dsl_dataset_hold_flags(). If the key on the
receiving side isn't loaded or the send stream contains embedded
blocks, the receive check fails for a stream which is perfectly
valid and could be received without any problem. This seems like
a remnant of the initial design, where unencrypted datasets below
encrypted ones weren't allowed.
Add a condition to set `DS_HOLD_FLAG_DECRYPT` only for encrypted
datasets, modify an existing test to detect this regression and add
a test for raw replication streams.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Co-authored-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13033Closes#13076
To follow a change in illumos taskq
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12802
Currently, $(CC), $(LD), and $(LLVM) variables aren't passed to kbuild
while building modules. This causes modules to build with the default
GNU GCC toolchain and prevents experimenting with other toolchains such
as CLANG/LLVM. It can also lead to build failure if the CFLAGS/LDFLAGS
passed are incompatible with gcc/ld.
Pass $KERNEL_CC, $KERNEL_LD, and $KERNEL_LLVM as $(CC), $(LD), and
$(LLVM), respectively, to kbuild for each that is defined in the
environment. This should take care of the majority of alternative
toolchain use cases.
Reviewed-by: Damian Szuberski <szuberskidamian@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Peter Levine <plevine457@gmail.com>
Closes#13046
Linux 5.16 moved XSTATE_XSAVE and XSTATE_XRESTORE out of our reach,
so add our own XSAVE{,OPT,S} code and use it for Linux 5.16.
Please note that this differs from previous behavior in that it
won't handle exceptions created by XSAVE an XRSTOR. This is sensible
for three reasons.
- Exceptions during XSAVE and XRSTOR can only occur if the feature
is not supported or enabled or the memory operand isn't aligned
on a 64 byte boundary. If this happens something else went
terribly wrong, and it may be better to stop execution.
- Previously we just printed a warning and didn't handle the fault,
this is arguable for the above reason.
- All other *SAVE instruction also don't handle exceptions, so this
at least aligns behavior.
Finally add a test to catch such a regression in the future.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#13042Closes#13059
All of these externs are already #included as static inline
functions via corresponding headers.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tomohiro Kusumi <kusumi.tomohiro@gmail.com>
Closes#13073
There's no need to make the platform ops dynamic dispatch.
This change replaces the dynamic dispatch with static calls to the
platform-specific functions.
To avoid name collisions, prefix all platform-specific functions
with `zvol_os_`.
I actually find `zvol_..._os` slightly nicer to read in the calling
code, but having it as a prefix is useful.
Advantage:
- easier jump-to-definition / grepping
- potential benefits to static analysis
- better legibility
Future work: also prefix remaining `static` functions in zvol_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12965
Use error thresholds from policy to control whether to scrub data
and/or metadata. If threshold is set to UINT64_MAX, then caller
probably does not care about result and we may skip that part.
By default import neither set the data error threshold nor read
the error counter, so skip the data scrub for faster import.
Metadata are still scrubbed and fail if even single error found.
While there just for symmetry return number of metadata errors in
case threshold is not set to zero and we haven't reached it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#13022
The following commit moved the users of `deferred` into function
dsl_pool_unreserved_space:
commit d2734cce68
Author: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
Date: Fri Dec 16 14:11:29 2016 -0800
OpenZFS 9166 - zfs storage pool checkpoint
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#13056
POSIX requires that set-uid and set-gid bits to be removed when an
unprivileged user writes to a file and ZFS does that during normal
operation.
The problem arrises when the write is stored in the ZIL and replayed.
During replay we have no access to original credentials of the process
doing the write, so zfs_write() will be performed with the root
credentials. When root is doing the write set-uid and set-gid bits
are not removed from the file.
To correct that, log a separate TX_SETATTR entry that removed those bits
on first write to such file.
Idea from: Christian Schwarz
Add test for ZIL replay of setuid/setgid clearing.
Improve various edge cases when clearing setid bits:
- The setid bits can be readded during a single write, so make sure to check
for them on every chunk write.
- Log TX_SETATTR record at most once per transaction group (if the setid bits
are keep coming back).
- Move zfs_log_setattr() outside of zp->z_acl_lock.
Reviewed-by: Dan McDonald <danmcd@joyent.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Christian Schwarz <me@cschwarz.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#13027
`configure` now accepts `--enable-asan` and `--enable-ubsan` switches
which results in passing `-fsanitize=address`
and `-fsanitize=undefined`, respectively, to the compiler. Those
flags are enabled in GitHub workflows for ZTS and zloop. Errors
reported by both instrumentations are corrected, except for:
- Memory leak reporting is (temporarily) suppressed. The cost of
fixing them is relatively high compared to the gains.
- Checksum computing functions in `module/zcommon/zfs_fletcher*`
have UBSan errors suppressed. It is completely impractical
to enforce 64-byte payload alignment there due to performance
impact.
- There's no ASan heap poisoning in `module/zstd/lib/zstd.c`. A custom
memory allocator is used there rendering that measure
unfeasible.
- Memory leaks detection has to be suppressed for `cmd/zvol_id`.
`zvol_id` is run by udev with the help of `ptrace(2)`. Tracing is
incompatible with memory leaks detection.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: szubersk <szuberskidamian@gmail.com>
Closes#12928
In files created/modified before 4254acb there may be a corruption of
xattrs which is not reported during scrub and normal send/receive. It
manifests only as an error when raw sending/receiving. This happens
because currently only the raw receive path checks for discrepancies
between the dnode bonus length and the spill pointer flag.
In case we encounter a dnode whose bonus length is greater than the
predicted one, we should report an error. Modify in this regard
dnode_sync() with an assertion at the end, dump_dnode() to error out,
dsl_scan_recurse() to report errors during a scrub, and zstream to
report a warning when dumping. Also added a test to verify spill blocks
are sent correctly in a raw send.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12720Closes#13014
69 CSTYLED BEGINs remain, appx. 30 of which can be removed if cstyle(1)
had a useful policy regarding
CALL(ARG1,
ARG2,
ARG3);
above 2 lines. As it stands, it spits out *both*
sysctl_os.c: 385: continuation line should be indented by 4 spaces
sysctl_os.c: 385: indent by spaces instead of tabs
which is very cool
Another >10 could be fixed by removing "ulong" &al. handling.
I don't foresee anyone actually using it intentionally
(does it even exist in modern headers? why did it in the first place?).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12993
First open locking changes were correctly applied to zvol_geom_open but
incorrectly applied to zvol_cdev_open, causing spa_namespace_lock to be
held indefinitely.
Make the first open locking in zvol_cdev_open match zvol_geom_open.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#13016
When using the two argument version of submit_bio() in kernel's prior
to 4.8 the first argument should be specified. It's used by block
dump to report the bio direction.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#13006
Linux 5.17 sees a rename from complete_and_exit()
to kthread complete_and_exit()
Upstream commit cead18552660702a4a46f58e65188fe5f36e9dfe
("exit: Rename complete_and_exit to kthread_complete_and_exit")
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12989
For us, I think it's always just FALLOC_FL_PUNCH_HOLE with a fake
mustache on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
add_disk went from void to must-check int return.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12975
FreeBSD's implementation of zfs_uio_fault_move() returns EFAULT when a
page fault occurs while copying data in or out of user buffers. The VFS
treats such errors specially and will retry the I/O operation (which may
have made some partial progress).
When the FreeBSD and Linux implementations of zfs_write() were merged,
the handling of errors from dmu_write_uio_dbuf() changed such that
EFAULT is not handled as a partial write. For example, when appending
to a file, the z_size field of the znode is not updated after a partial
write resulting in EFAULT.
Restore the old handling of errors from dmu_write_uio_dbuf() to fix
this. This should have no impact on Linux, which has special handling
for EFAULT already.
Reviewed-by: Andriy Gapon <avg@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12964
Raw receiving a snapshot back to the originating dataset is currently
impossible because of user accounting being present in the originating
dataset.
One solution would be resetting user accounting when raw receiving on
the receiving dataset. However, to recalculate it we would have to dirty
all dnodes, which may not be preferable on big datasets.
Instead, we rely on the os_phys flag
OBJSET_FLAG_USERACCOUNTING_COMPLETE to indicate that user accounting is
incomplete when raw receiving. Thus, on the next mount of the receiving
dataset the local mac protecting user accounting is zeroed out.
The flag is then cleared when user accounting of the raw received
snapshot is calculated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12981Closes#10523Closes#11221Closes#11294Closes#12594
Issue #11300
When the eviction thread goes to shrink an ARC state, it allocates a set
of marker buffers used to hold its place in the state's sublists.
This can be problematic in low memory conditions, since
1) the allocation can be substantial, as we allocate NCPU markers;
2) on at least FreeBSD, page reclamation can block in
arc_wait_for_eviction()
In particular, in stress tests it's possible to hit a deadlock on
FreeBSD when the number of free pages is very low, wherein the system is
waiting for the page daemon to reclaim memory, the page daemon is
waiting for the ARC eviction thread to finish, and the ARC eviction
thread is blocked waiting for more memory.
Try to reduce the likelihood of such deadlocks by pre-allocating markers
for the eviction thread at ARC initialization time. When evicting
buffers from an ARC state, check to see if the current thread is the ARC
eviction thread, and use the pre-allocated markers for that purpose
rather than dynamically allocating them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12985
Evaluated every variable that lives in .data (and globals in .rodata)
in the kernel modules, and constified/eliminated/localised them
appropriately. This means that all read-only data is now actually
read-only data, and, if possible, at file scope. A lot of previously-
global-symbols became inlinable (and inlined!) constants. Probably
not in a big Wowee Performance Moment, but hey.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12899
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
These are the changes for FreeBSD corresponding to the changes made for
Linux in #12863, see that PR for details.
Changes from #12863 are applied for zvol_geom_open and zvol_cdev_open
on FreeBSD. This also adds a check for the zvol dying which we had
in zvol_geom_open but was missing in zvol_cdev_open. The check causes
the open to fail early with ENXIO when we are in the middle of changing
volmode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12934
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Maybee <mark.maybee@delphix.com>
Closes#12951
There should be no risk of us accidentally hitting this since
we'd need maliciously malformed data to wind up in the pipeline,
or a very unfortunate random bit flip at exactly the right moment.
Still since we can handle it we should.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12947
As an experiment, I stole the lz4 decompressor from
upstream lz4 (1.9.3), and landed it.
Feedback suggested that keeping the vendor lz4 code isolated and
unlinted was probably reasonable, so I lobbed it into its own file.
It also seemed reasonable to put the mostly-untouched* code into
lz4.c proper, and relegate the integrated and ZFS-specific code to
lz4_zfs.c.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12805
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12895Closes#12902
After progressively folding away null cases, it turns out there's
/literally/ nothing there, even if some things are part of the
Solaris SPARC DDI/DKI or the seventeen module types (some doubled for
32-bit userland), or the entire modctl syscall definition.
Nothing.
Initialisation is handled in illumos-crypto.c,
which calls all the initialisers directly
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Attila Fülöp <attila@fueloep.org>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12895Closes#12902
Probably introduced inadvertently in b525630 (Native Encryption).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Christian Schwarz <christian.schwarz@nutanix.com>
Closes#12935
Fix from https://github.com/openzfs/zfs/pull/12844#discussion_r774179413
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12905
This reverts commit f6a0dac84a.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12938
sc.nr_to_scan is an input to super_cache_clean (via
shrinker->scan_objects), used to set the number of objects to scan
in the various caches. However super_cache_scan also modifies
sc.nr_to_scan, so when used in a loop we need to reset
sc.nr_to_scan back to our desired nr_to_scan for the next
iteration.
Issue discovered and solution suggested by
Tenzin Lhakhang @tlhakhan.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chris Dunlop <chris@onthe.net.au>
Issue #12433Closes#12908
Verify that all empty sectors are zero filled before using them to
calculate parity. Failure to do so can result in incorrect parity
columns being generated and written to disk if the contents of an
empty sector are non-zero. This was possible because the checksum
only protects the data portions of the buffer, not the empty sector
padding.
This issue has been addressed by updating raidz_parity_verify() to
check that all dRAID empty sectors are zero filled. Any sectors
which are non-zero will be fixed, repair IO issued, and a checksum
error logged. They can then be safely used to verify the parity.
This specific type of damage is unlikely to occur since it requires
a disk to have silently returned bad data, for an empty sector, while
performing a scrub. However, if a pool were to have been damaged
in this way, scrubbing the pool with this change applied will repair
both the empty sector and parity columns as long as the data checksum
is valid. Checksum errors will be reported in the `zpool status`
output for any repairs which are made.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12857
When performing I/O on FreeBSD using a file based vdev ensure all
errors encountered when reading/writing are propagated through the
zio pipeline.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12904
On FreeBSD vnode reclamation is single-threaded, protected by single
global lock. Linux seems to be able to use a thread per mount point,
but at this time it creates more harm than good.
Reduce number of threads to 1, adding tunable in case somebody wants
to try more.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chris Dunlop <chris@onthe.net.au>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12896
Issue #9966
Provide access to file generation number on Linux.
Add test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12856
Debian ships fake System.map files by default, leading to the
invocation of depmod with them to flood you with errors about
missing symbols.
Let's notice and not do that.
Reviewed-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12862
When restructuring the zvol_open() logic for the Linux 5.13 kernel
a lock inversion was accidentally introduced. In the updated code
the spa_namespace_lock is now taken before the zv_suspend_lock
allowing the following scenario to occur:
down_read <=== waiting for zv_suspend_lock
zvol_open <=== holds spa_namespace_lock
__blkdev_get
blkdev_get_by_dev
blkdev_open
...
mutex_lock <== waiting for spa_namespace_lock
spa_open_common
spa_open
dsl_pool_hold
dmu_objset_hold_flags
dmu_objset_hold
dsl_prop_get
dsl_prop_get_integer
zvol_create_minor
dmu_recv_end
zfs_ioc_recv_impl <=== holds zv_suspend_lock via zvol_suspend()
zfs_ioc_recv
...
This commit resolves the issue by moving the acquisition of the
spa_namespace_lock back to after the zv_suspend_lock which restores
the original ordering.
Additionally, as part of this change the error exit paths were
simplified where possible.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12863
A recent commit to FreeBSD changed the type of
vop_readdir_args.a_cookies to a uint64_t**. There is no functional
impact to ZFS because ZFS only uses 32-bit cookies, which will be
zero-extended to 64-bits by the existing code.
b214fcceac
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#12874
If sufficient memory (<2K, realistically) is available, libzfs_init()
can be significantly shorted by iterating over the correct sysfs
directory before registrations, we can turn 168 stats into 15/18
syscalls (3 opens (6 if built in), 3 fstats, 6 getdentses, and 3
closes), a tenfoldish reduction; this is probably a bit faster, too.
The list is always optional, and registration functions (and one-off
users) can simply pass NULL, which will fall back to the previous
mechanism
Also, don't allocate in zfs_mod_supported_impl, and use use access()
instead of stat(), since existence is really what we care about
Also, fix pre-prop-checking compat in fallback for built-in ZFS
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12089
They're already static, and there's no point in them being R/W
and living outside .rodata
Reviewed-by: RageLtMan <rageltman@sempervictus>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12836
va_seq was actually a thin veil over va_gen, so z_gen is a more
appropriate value than z_seq to populate the field with.
Drop the unnecessary compat obfuscation and provide the correct
file generation number.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@freebsd.org>
Closes#12851
If the fields to be listed and sorted by are constrained
to those populated by dsl_dataset_fast_stat(), then
zfs list is much faster, as it does not need to open each
objset and reads its properties.
A previous optimization by Pawel Dawidek
(0cee24064a) took advantage
of this to make listing snapshot names sorted only by name
much faster.
However, it was limited to `-o name -s name`, this work
extends this optimization to work with:
- name
- guid
- createtxg
- numclones
- inconsistent
- redacted
- origin
and could be further extended to any other properties
supported by dsl_dataset_fast_stat() or similar, that do
not require extra locking or reading from disk.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11080
When rolling back a dataset, ZFS has to purge file data resident in the
system page cache. To do this, it loops over all vnodes for the
mountpoint and calls vn_pages_remove() to purge pages associated with
the vnode's VM object. Each page is thus exclusively busied while the
dataset's teardown write lock is held.
When handling a page fault on a mapped ZFS file, FreeBSD's page fault
handler busies newly allocated pages and then uses VOP_GETPAGES to fill
them. The ZFS getpages VOP acquires the teardown read lock with vnode
pages already busied. This represents a lock order reversal which can
lead to deadlock.
To break the deadlock, observe that zfs_rezget() need only purge those
pages marked valid, and that pages busied by the page fault handler are,
by definition, invalid. Furthermore, ZFS pages always transition from
invalid to valid with the teardown lock held, and ZFS never creates
partially valid pages. Thus, zfs_rezget() can use the new
vn_pages_remove_valid() to skip over pages busied by the fault handler.
PR: 258208
Tested by: pho
Reviewed by: avg, sef, kib
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D32931
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#12828
This chases 269b5dadcf (#12735),
which touched the actual code but didn't fix the comment
Additionally, ignore the name.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12823
Newer zstd code introduced in the main kernel tree now creates a symbol
collision with ZSTD_isError in our ZSTD code. This change relabels our
implementation with a ZFS-specific symbol name, and undoes some
macro-based micro-optimizations that conflict with the attempt to rename
our internal-use version.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The definition of struct blkcg_gq was moved into blk-cgroup.h, which is
a header that's been in Linux since 2015. This is used by
vdev_blkg_tryget() in module/os/linux/zfs/vdev_disk.c. Since the kernel
for CentOS 7 and similar-generation releases doesn't have this header,
its inclusion is guarded by a configure test.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
This change adds a confiugre check to determine if bio_set_dev is a
helper macro or not. If not, then the attempt to override its internal
call to bio_associate_blkg(), with a macro definition to our own
version, is no longer possible, as the compiler won't use it when
compiling the new inline function replacement implemented in the header.
This change also creates a new vdev_bio_set_dev() function that performs
the same work, and also performs the work implemented in
vdev_bio_associate_blkg(), as it is the only thing calling that function
in our code. Our custom vdev_bio_associate_blkg() is now only compiled
if the bio_set_dev() is a macro in the Linux headers.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The iov_iter->type member was renamed iov_iter->iter_type. However,
while looking into this, realized that in 2018 a iov_iter_type(*iov)
accessor function was introduced. So if that is present, use it,
otherwise fall back to trying the existing behavior of directly
accessing type from iov_iter.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
The return type for the submit_bio member of struct
block_device_operations was changed to no longer return a value.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12819
Improve the ability of zfs send to determine if a block is compressed
or not by using information contained in the blkptr.
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Reviewed-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12770
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12728
For my sins, I started running valgrind over ztest to try and fix
that pesky intermittent "zloop dies with malloc errors" problem.
This one seemed exciting enough to merit cutting a PR for before
the rest get polished.
Suggested-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12214
Due to a possible lock inversion the zvol open call path on Linux
needs to be able to retry in the case where the spa_namespace_lock
cannot be acquired.
For Linux 5.12 an older kernel this was accomplished by returning
-ERESTARTSYS from zvol_open() to request that blkdev_get() drop
the bdev->bd_mutex lock, reaquire it, then call the open callback
again. However, as of the 5.13 kernel this behavior was removed.
Therefore, for 5.12 and older kernels we preserved the existing
retry logic, but for 5.13 and newer kernels we retry internally in
zvol_open(). This should always succeed except in the case where
a pool's vdev are layed on zvols, in which case it may fail. To
handle this case vdev_disk_open() has been updated to retry when
opening a device when -ERESTARTSYS is returned.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #12301Closes#12759
Strict hole reporting was previously disabled by default as a
performance optimization. However, this has lead to confusion
over the expected behavior and a variety of workarounds being
adopted by consumers of ZFS. Change the default behavior to
always report holes and force the TXG sync.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12746
- Allocate ve_search on the stack, so we avoid allocating memory for
every I/O even if the VDEV cache is disabled.
- Reduce lock scope.
- Avoid locking in vdev_cache_read() when the VDEV cache is disabled.
- Sort file names properly.
- Correct comment.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12749
Add properties, similar to pool properties, to each vdev.
This makes use of the existing per-vdev ZAP that was added as
part of device evacuation/removal.
A large number of read-only properties are exposed,
many of the members of struct vdev_t, that provide useful
statistics.
Adds support for read-only "removing" vdev property.
Adds the "allocating" property that defaults to "on" and
can be set to "off" to prevent future allocations from that
top-level vdev.
Supports user-defined vdev properties.
Includes support for properties.vdev in SYSFS.
Co-authored-by: Allan Jude <allan@klarasystems.com>
Co-authored-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#11711
Instead, linux/pagemap.h offers a number of folio-specific functions to
be called instead. In this case, module/os/linux/zfs/zfs_vnops_os.c
wants to call wait_on_page_bit(pp, PG_writeback). This gets replaced
with folio_wait_bit(folio_page(pp), PG_writeback). This change modifies
the code to conditionally compile that if configure identifies th
presence of the folio_wait_bit() function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12800
- To avoid a use-after-free, zfsvfs->z_log needs to be loaded after the
teardown lock is acquired with ZFS_ENTER().
- Avoid leaking vnode locks in zfs_rename_relock() and zfs_rename_()
when the ZFS_ENTER() macros forces an early return.
Refactor the rename implementation so that ZFS_ENTER() can be used
safely. As a bonus, this lets us use the ZFS_VERIFY_ZP() macro instead
of open-coding its implementation.
Reported-by: Peter Holm <pho@FreeBSD.org>
Tested-by: Peter Holm <pho@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12717
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12771
The code is integrated, builds fine, runs fine, there's not really
any reason not to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12735
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12748
Special allocation class or dedup vdevs may have roughly the same
performance as L2ARC vdevs. Introduce a new tunable to exclude those
buffers from being cacheable on L2ARC.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11761Closes#12285
The l2cache device could be added twice because vdev_inuse() does not
check spa_l2cache for added devices. Make l2cache vdevs inuse checking
logic more closer to spare vdevs.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9153Closes#12689
In addition to flushing memory mapped regions when checking holes,
commit de198f2d95 modified the dirty dnode detection logic to check
the dn->dn_dirty_records instead of the dn->dn_dirty_link. Relying
on the dirty record has not be reliable, switch back to the previous
method.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12745
The only zdb utility require to read metaslab-related data during
read-only pool import because of spacemaps validation. Add global
variable which will allow zdb read spacemaps in case of readonly
import mode.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Fedor Uporov <fuporov.vstack@gmail.com>
Closes#9095Closes#12687
In order to reduce contention on the vq_lock, optional skip sectors
for Raidz writes can be placed into a single IO request. This is done by
padding out the linear ABD for a parity column to contain the skip
sector and by creating gang ABD to contain the data and skip sector for
data columns.
The vdev_raidz_map_alloc() function now contains specific functions for
both reads and write to allocate the ABD's that will be issued down to
the VDEV chldren.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-By: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#12333
The submit_bio() prototype has changed again. The version is 5.16
still only expects a single argument but the return type has changed
to void. Since we never used the returned value before update the
configure check to detect both single arg versions.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12725
When using lseek(2) to report data/holes memory mapped regions of
the file were ignored. This could result in incorrect results.
To handle this zfs_holey_common() was updated to asynchronously
writeback any dirty mmap(2) regions prior to reporting holes.
Additionally, while not strictly required, the dn_struct_rwlock is
now held over the dirty check to prevent the dnode structure from
changing. This ensures that a clean dnode can't be dirtied before
the data/hole is located. The range lock is now also taken to
ensure the call cannot race with zfs_write().
Furthermore, the code was refactored to provide a dnode_is_dirty()
helper function which checks the dnode for any dirty records to
determine its dirtiness.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Rich Ercolani <rincebrain@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11900Closes#12724
It turns out that short-circuiting the EFAULT behavior on a short read
breaks things on FreeBSD. So until there's a nicer solution, let's
just revert the behavior for not-Linux.
Reference:
https://reviews.freebsd.org/R10:70f51f0e474ffe1fb74cb427423a2fba3637544d
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12698
On Linux, sometimes, when ZFS goes to unmount an automounted snap,
it fails a VERIFY check on debug builds, because taskq_cancel_id
returned ENOENT after not finding the taskq it was trying to cancel.
This presumably happens when it already died for some reason; in this
case, we don't really mind it already being dead, since we're just
going to dispatch a new task to unmount it right after.
So we just ignore it if we get back ENOENT trying to cancel here,
retry a couple times if we get back the only other possible condition
(EBUSY), and log to dbgmsg if we got anything but ENOENT or success.
(We also add some locking around taskqid, to avoid one or two cases
of two instances of trying to cancel something at once.)
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#11632Closes#12670
We move the spinlock unlock before the thread creation. This should be
safe because the thread creation code doesn't actually manipulate any
taskq data structures; that's done by the thread once it's created.
We also remove the assertion that the maxthreads is the current threads
plus one; that assertion could fail if multiple hotplug events come in
quick succession, and the first new taskq thread hasn't had a chance to
start processing yet.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
eviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12714
We have to hold the teardown lock while dereferencing zfsvfs->z_os and,
I believe, when committing to the ZIL.
Note that jumping to the "out" label, "error" is always non-zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
The objset object is reallocated during certain dataset operations, such
as rollbacks, so the objset pointer must be loaded after acquiring the
teardown lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12704
If you've got multiple scrubs/resilvers going, it's rather helpful
to know which pool each scan line refers to.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12674
The fnvlist versions of the functions are fatal if they fail,
saving each call from having to include checking the result.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Remove code duplication by moving code responsible for partial block
zeroing to a separate function: dnode_partial_zero().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12627
Make the main dmu_buf_hold_array() function non-static.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Pawel Jakub Dawidek <pawel@dawidek.net>
Closes#12628
Lustre makes light use of the zfs_refcount interfaces which
isn't a problem when using a non-debug build of OpenZFS. However,
when debugging is enabled the required symbols are not exported.
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12613
refcount_add_many(foo,N) is not the same as
for (i=0; i < N; i++) { refcount_add(foo); }
Unfortunately, this is only actually true with debug kernels and
reference_tracking_enable=1.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12589Closes#12602
When you create a pool, zfs writes vd->vdev_enc_sysfs_path with the
enclosure sysfs path to the fault LEDs, like:
vdev_enc_sysfs_path = /sys/class/enclosure/0:0:1:0/SLOT8
However, this enclosure path doesn't get updated on successive imports
even if enclosure path to the disk changes. This patch fixes the issue.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Tony Hutter <hutter2@llnl.gov>
Closes#11950Closes#12095
Commit 0c03d21ac9 left in a redundant if condition while
removing some code. Just remove it.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12598
Currently, dmu_read_uio_dnode can read 64K of a requested 1M in one
loop, get EFAULT back from zfs_uiomove() (because the iovec only holds
64k), and return EFAULT, which turns into EAGAIN on the way out. EAGAIN
gets interpreted as "I didn't read anything", the caller tries again
without consuming the 64k we already read, and we're stuck.
This apparently works on newer kernels because the caller which breaks
on older Linux kernels by happily passing along a 1M read request and a
64k iovec just requests 64k at a time.
With this, we now won't return EFAULT if we got a partial read.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12370Closes#12509Closes#12516
While switching abd_zero_buf allocation KPI I've missed the fact
that kmem_zalloc() zeroed the allocation, while kmem_cache_alloc()
does not. Add explicit bzero() after it.
I don't think it should have caused real problems, but leaking one
memory page content all over the pool is not good.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12569
In case an ARC buffer is allocated only on L2ARC, and there are
underlying errors in a pool with the cache device in faulty state, a
panic can occur in arc_read_done()->arc_hdr_destroy()->
arc_hdr_l2arc_destroy()->arc_hdr_clear_flags() when trying to free
the ARC buffer.
Fix this by discarding the buffer's identity in arc_hdr_destroy(), in
case the buffer is not empty, before calling arc_hdr_l2hdr_destroy().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12392
When mounting a snapshot in the .zfs/snapshots control directory,
temporarily assume roots credentials to perform the VFS_MOUNT().
This allows regular users and users inside jails to access these
snapshots.
The regular usermount code is not helpful here, since it requires
that the user performing the mount own the mountpoint, which won't
be the case for .zfs/snapshot/<snapname>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Modirum MDPay
Sponsored-By: Klara Inc.
Closes#11312
As of the Linux 5.9 kernel a fallthrough macro has been added which
should be used to anotate all intentional fallthrough paths. Once
all of the kernel code paths have been updated to use fallthrough
the -Wimplicit-fallthrough option will because the default. To
avoid warnings in the OpenZFS code base when this happens apply
the fallthrough macro.
Additional reading: https://lwn.net/Articles/794944/
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12441
Userland figures out which encryption-root keys are required to load,
and issues ZFS_IOC_LOAD_KEY.
The tail section of spa_keystore_load_wkey() will call
zvol_create_minors() on the encryption-root object.
Any clones of the encrypted zvol will not be plumbed. This commits
adds additional logic to detect if zvol has clones, and is encrypted,
then adds these to the list of zvols to call zvol_create_minors() on.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12471
Errors in zil_lwb_write_done() are not propagated to
zil_lwb_flush_vdevs_done() which can result in zil_commit_impl()
not returning an error to applications even when zfs was not able
to write data to the disk.
Remove the ZIO_FLAG_DONT_PROPAGATE flag from zio_rewrite() to
allow errors to propagate and consolidate the error handling for
flush and write errors to a single location (rather than having
error handling split between the "write done" and "flush done"
handlers).
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Signed-off-by: Arun KV <arun.kv@datacore.com>
Closes#12391Closes#12443
The block pointer verification check in arc_read() should also
cover embedded block pointers. While highly unlikely, accessing
a damaged block pointer can result in panic. To further harden
the code extend the existing check to include embedded block
pointers and add a comment explaining the rational for this
sanity check. Lastly, correct a flaw in zfs_blkptr_verify()
so the error count is checked even when checking a untrusted
config to verify the non-pool-specific portions of a block
pointer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12535
For kernel to send snapshot mount/unmount events to zed.
For kernel to send symlink creates/removes on zvol plumbing.
(/dev/run/dsk/zvol/$pool/$zvol -> /dev/diskX)
If zed misses the ENODEV, all errors after are EINVAL. Treat any error
as kernel module failure.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12416
Kernel commits
332f606b32b6 ovl: enable RCU'd ->get_acl()
0cad6246621b vfs: add rcu argument to ->get_acl() callback
Added compatibility code to detect the new ->get_acl() interface
and correctly handle the case where the new rcu argument is set.
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12548
When zfs_send_corrupt_data is set, use the TRAVERSE_HARD flag,
so traverse_visitbp() will not fail with ECKSUM if a blockpointer
cannot be read, but rather will continue and send the objects it can.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Sponsored-By: Klara Inc.
Sponsored-By: WHC Online Solutions Inc.
Closes#12541
Unfortunately, there was an overzealous assertion that was (in pretty
specific circumstances) false, causing failure. This assertion was
added in error, so we're removing it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#9897Closes#12020Closes#12246
We round up the psize to the nearest multiple of the asize or to the
lsize, whichever is smaller. Once that's done, we allocate a new
buffer of the appropriate size, zero the tail, and copy the data
into it. This adds a small performance cost to these kinds of writes,
but fixes the bookkeeping problems.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#12522Closes#8462
We attempt to remove an existing SA xattr when setting a dir xattr, but
this only makes sense if the znode has been upgraded to the SA format.
Otherwise, we will hit an assert in zfs_sa_get_xattr.
Make sure this is an SA znode before attempting to remove the SA xattr.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12514
It turns out that layouts of union bitfields are a pain, and the
current code results in an inconsistent layout between BE and LE
systems, leading to zstd-active datasets on one erroring out on
the other.
Switch everyone over to the LE layout, and add compatibility code
to read both.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12008Closes#12022
This adds supports for hole-punching facilities in the FreeBSD kernel
starting from __FreeBSD_version 1400032.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Ka Ho Ng <khng@FreeBSD.org>
Sponsored-by: The FreeBSD Foundation
Closes#12458
Previously, zpool-iostat did not display any data regarding rebuild I/Os
in either the latency/size histograms (-w/-l/-r) or the queue data (-q).
This fix essentially utilizes the existing infrastructure for tracking
rebuild queue data and displays this data in the proper places within
zpool-iostat's output.
Signed-off-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Signed-off-by: Trevor Bautista <tbautista@lanl.gov>
Co-authored-by: Trevor Bautista <tbautista@newmexicoconsortium.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
benchmark_raidz() allocates a row to benchmark parity calculation and
reconstruction. In the latter case, the parity blocks are left
uninitialized, leading to reports from KMSAN.
Initialize parity blocks to 0xAA as we do for the data earlier in the
function. This does not affect the selected RAID-Z implementation on
any of several systems tested.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12473
Linux 4.11 added a new statx system call that allows us to expose crtime
as btime. We do this by caching crtime in the znode to match how atime,
ctime and mtime are cached in the inode.
statx also introduced a new way of reporting whether the immutable,
append and nodump bits have been set. It adds support for reporting
compression and encryption, but the semantics on other filesystems is
not just to report compression/encryption, but to allow it to be turned
on/off at the file level. We do not support that.
We could implement semantics where we refuse to allow user modification
of the bit, but we would need to do a dnode_hold() in zfs_znode_alloc()
to find out encryption/compression information. That would introduce
locking that will have a minor (although unmeasured) performance cost.
It also would be inferior to zdb, which reports far more detailed
information. We therefore omit reporting of encryption/compression
through statx in favor of recommending that users interested in such
information use zdb.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Richard Yao <ryao@gentoo.org>
Closes#8507
When a header is allocated for full overwrite it is a waste of time
to allocate b_pabd/b_rabd for it, since arc_write() will free them
without ever being touched. If it is a read or a partial overwrite
then arc_read() and arc_hdr_decrypt() allocate them explicitly.
Reduced memory allocation in user threads also reduces ARC eviction
throttling there, proportionally increasing it in ZIO threads, that
is not good. To minimize or even avoid it introduce ARC allocation
reserve, allowing certain arc_get_data_abd() callers to allocate a
bit longer in situations where user threads will already throttle.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12398
It is very expensive and not informative to call multilist_is_empty()
for each arc_change_state() on debug builds to check for impossible.
Instead implement special index function for arc_l2c_only->arcs_list,
multilists, panicking on any attempt to use it.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12421
Instead of clearing stats inside arc_buf_alloc_impl() do it inside
arc_hdr_alloc() and arc_release(). It fixes statistics being wiped
every time a new dbuf is filled from the ARC.
Remove b_l1hdr.b_l2_hits. L2ARC hits are accounted at b_l2hdr.b_hits.
Since the hits are accounted under hash lock, replace atomics with
simple increments.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <george.wilson@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12422
vq_lock is already too congested for two more operations per I/O.
Instead of dropping and reacquiring it inside vdev_queue_aggregate()
delegate the zio_vdev_io_bypass() and zio_execute() calls for parent
I/Os to callers, that drop the lock any way to execute the new I/O.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12297
Use atomic_load_64() for zfs_refcount_count() to prevent torn reads
on 32-bit platforms. On 64-bit ones it should not change anything.
When built with ZFS_DEBUG but running without tracking enabled use
atomics instead of mutexes same as for builds without ZFS_DEBUG.
Since rc_tracked can't change live we can check it without lock.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12420
Before OpenZFS 2.0, trying to set the FreeBSD sysctl vfs.zfs.arc_max
to a disallowed value would return an error.
Since the switch, it instead only generates WARN_IF_TUNING_IGNORED
Keep the ability to set the sysctl's specifically to 0, even though
that is less than the minimum, because some tests depend on this.
Also lost, was the ability to set vfs.zfs.arc_max to a value less
than the default vfs.zfs.arc_min at boot time. Restore this as well.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Closes#12161
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Martin Matuska <mm@FreeBSD.org>
Co-authored-by: Konstantin Belousov <kib@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
External-issue: https://reviews.freebsd.org/D31207Closes#12442
Run arc_evict thread at higher priority, nice=0, to give it more CPU
time which can improve performance for workload with high ARC evict
activities.
On mixed read/write and sequential read workloads, I've seen between
10-40% better performance.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Tony Nguyen <tony.nguyen@delphix.com>
Closes#12397
The /proc/diskstats accounting needs to be explicitly enabled
for block devices which do not use multi-queue.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12440Closes#12066
CpaDcGeneratefooter function that obtain the checksum code
does not support the CPA_DC_STATELESS mode. So we get the
adler32 chencksum of the end of the zlib from dc_results.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Chengfei Zhu <chengfeix.zhu@intel.com>
Signed-off-by: hedong.zhang <h_d_zhang@163.com>
Closes#12343
We have a tunable which permits one to disable the use of unmapped I/O
for the buffer cache. Respect it in ZFS as well. This is useful for
KMSAN, which cannot easily maintain shadow state for unmapped pages.
No functional change intended, as unmapped I/O is permitted by default
and there's no real reason to disable it in practice except for
debugging.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12446
It is wrong for arc_write_ready() to use zfs_abd_scatter_enabled to
decide whether to reallocate/copy the buffer, because the answer is
OS-specific and depends on the buffer size. Instead of that use
abd_size_alloc_linear(), moved into public header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12425
Commit 5dbf6c5a66 did not address these format specifier warnings
since they were introduced by an unrelated commit which had not
been rebased on 5dbf6c5a66 when merged. Fix them.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12435
In l2arc_add_vdev() first decide whether the device is eligible for
L2ARC rebuild or whole device trim and then add it to the list of cache
devices. Otherwise l2arc_feed_thread() might already start writing on
the device invalidating previous content as l2ad_hand = l2ad_start.
However l2arc_rebuild_vdev() needs the device present in the cache
device list to figure out its l2arc_dev_t. Fix this by moving most of
l2arc_rebuild_vdev() in a new function l2arc_rebuild_dev() which does
not need to search in the cache device list.
In contrast to l2arc_add_vdev() we do not have to worry about
l2arc_feed_thread() invalidating previous content when onlining a
cache device. The device parameters (l2ad*) are not cleared when
offlining the device and writing new buffers will not invalidate
all previous content. In worst case only buffers that have not had
their log block written to the device will be lost.
Retire persist_l2arc_00{4,5,8} tests since they cover code already
covered by the remaining ones. Test persist_l2arc_006 is renamed to
persist_l2arc_004 and persist_l2arc_007 is renamed to persist_l2arc_005.
Fix a typo in persist_l2arc_004, and remove an assertion that is not
always true from l2arc_arcstats_pos. Also update an assertion in
persist_l2arc_005 and explain why in a comment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12365
These were mostly used to annotate do {} while(0)s
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
This includes a simplification of mkbusy and format correctness in zhack
and ztest
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #12201
It seems nothing ensures that this array is zeroed when a dnode is
freshly allocated, so in principle it retains the values from the
previous allocation. In practice it seems to be the case that the
fields should end up zeroed, but we can zero the field anyway for
consistency.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging a TX_WRITE record in the case where file data has to be
copied from the DMU, we pad the log record size to a multiple of 8
bytes. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When allocating a record, we round up the allocation size to a multiple
of 8. In this case, any padding bytes should be zeroed, otherwise the
contents of uninitialized memory are written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
When logging TX_SETATTR, we could otherwise fail to initialize part of
the corresponding ZIL record depending on which fields are present in
the xvattr. Initialize the creation time and the AV scan timestamp to
zero so that uninitialized bytes are not written to the ZIL.
This was found using KMSAN.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
spa_prop_find() may fail to find the specified property, in which case
it suppresses ENOENT from zap_lookup(). In this case, the return value
is left uninitialized, so spa_autoreplace was being initialized using an
uninitialized stack variable.
This was found using KMSAN. It appears to be a regression from commit
9eb7b46ed0, which removed the initialization of "autoreplace" from the
definition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#12383
Kernel 5.14 introduced a change where set_page_dirty of
struct address_space_operations is no longer implicitly set to
__set_page_dirty_buffers(), which ended up resulting in a NULL
pointer deref in the kernel when it is attempted to be called.
This change sets .set_page_dirty in the structure to
__set_page_dirty_nobuffers(), which was introduced with the
related patch set. The breaking change was introduce in commit
0af573780b0b13fceb7fabd49dc1b073cee9a507 to torvalds/linux.git.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#12427
After 1325434b, we can in certain circumstances end up calling
spa_update_dspace with vd->vdev_mg NULL, which ends poorly during
vdev removal.
So let's not do that further space adjustment when we can't.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12380Closes#12428
In Linux 5.14, blk_alloc_queue is no longer exported, and its usage
has been superseded by blk_alloc_disk, which returns a gendisk struct
from which we can still retrieve the struct request_queue* that is
needed in the one place where it is used. This also replaces the call
to alloc_disk(minors), and minors is now set via struct member
assignment.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Olaf Faaland <faaland1@llnl.gov>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12362Closes#12409
Since errors returned by zvol_create_minor_impl() are ignored by the
common code, it is more convenient to ignore make_dev_s() errors there.
It allows, for example, to get device created for the zvol after later
rename instead of having it further stuck in half-created state.
zvol_rename_minor() already ignores those errors.
While there, switch from MAXPHYS to maxphys in FreeBSD 13+.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12375
Remove mc_lock use from metaslab_class_throttle_*(). The math there
is based on refcounts and so atomic, so the only race possible there
is between zfs_refcount_count() and zfs_refcount_add(). But in most
cases metaslab_class_throttle_reserve() is called with the allocator
lock held, which covers the race. In cases where the lock is not
held, GANG_ALLOCATION() or METASLAB_MUST_RESERVE are set, and so we
do not use zfs_refcount_count(). And even if we assume some other
non-existing scenario, the worst that may happen from this race is
few more I/Os get to allocation earlier, that is not a problem.
Move locks and data of different allocators into different cache
lines to avoid false sharing. Group spa_alloc_* arrays together
into single array of aligned struct spa_alloc spa_allocs. Align
struct metaslab_class_allocator.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12314
* Add Module Parameters Regarding Log Size Limit
zfs_wrlog_data_max
The upper limit of TX_WRITE log data. Once it is reached,
write operation is blocked, until log data is cleared out
after txg sync. It only counts TX_WRITE log with WR_COPIED
or WR_NEED_COPY.
Reviewed-by: Prakash Surya <prakash.surya@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12284
Remove unneeded global, practically constant, state pointer variables
(arc_anon, arc_mru, etc.), replacing them with macros of real state
variables addresses (&ARC_anon, &ARC_mru, etc.).
Change ARC_EVICT_ALL from -1ULL to UINT64_MAX, not requiring special
handling in inner loop of ARC reclamation. Respectively change bytes
argument of arc_evict_state() from int64_t to uint64_t.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12348
Ensure all calls to bqueue_init() has a corresponding call to bqueue_destroy()
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12118
* zio: avoid callback typecasting
* zil: avoid zil_itxg_clean() callback typecasting
* zpl: decouple zpl_readpage() into two separate callbacks
* nvpair: explicitly declare callbacks for xdr_array()
* linux/zfs_nvops: don't use external iput() as a callback
* zcp_synctask: don't use fnvlist_free() as a callback
* zvol: don't use ops->zv_free() as a callback for taskq_dispatch()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12260
We should use SET_ERROR when we first get an error.
Add it in the FreeBSD xattr implementations where missing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12356
We don't use or need the pool name or value source in the zvol tasks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#12361
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12378
Most of dsl_dir_diduse_space() and dsl_dir_transfer_space() CPU time
is a dd_lock overhead and time spent in dmu_buf_will_dirty(). Calling
them one after another is a waste of time and even more contention.
Doing that twice for each rewritten block within dbuf_write_done()
via dsl_dataset_block_kill() and dsl_dataset_block_born() created one
of the biggest CPU overheads in case of small blocks rewrite.
dsl_dir_diduse_transfer_space() combines functionality of these two
functions for cases where it is needed, but without double overhead,
practically for the cost of dsl_dir_diduse_space() or even cheaper.
While there, optimize dsl_dir_phys() calls in dsl_dir_diduse_space()
and dsl_dir_transfer_space(). It seems Clang detects some aliasing
there, repeating dd->dd_dbuf->db_data dereference multiple times,
increasing dd_lock scope and contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Author: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12300
* Tinker with slop space accounting with dedup
Do not include the deduplicated space usage in the slop space
reservation, it leads to surprising outcomes.
* Update spa_dedup_dspace sometimes
Sometimes, we get into spa_get_slop_space() with
spa_dedup_dspace=~0ULL, AKA "unset", while spa_dspace is correctly set.
So call the code to update it before we use it if we hit that case.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12271
arc_evict_hdr() returns number of evicted bytes in scope of specific
state. For ghost states it does not mean the amount of really freed
memory, but the logical buffer size. It is correct for the eviction
process, but not for waking up threads waiting for ARC size reduction,
as added in "Revise ARC shrinker algorithm" commit, causing premature
wakeups while ARC is still overflowed, allowing even bigger overflow,
plus processing overhead when next allocation will also get blocked,
probably also for too short time.
To fix that make arc_evict_hdr() also return the amount of really
freed memory, which for the ghost states is only the header, and use
it to update arc_evict_count instead. Originally I was thinking to
not return it at all, since arc_get_data_impl() does not account for
the headers, but decided that some slow allocation progress is better
than long waits, reaching on my tests up to 100ms.
To reduce negative latency effects of long time periods when reclaim
thread can free little real memory, start reclamation process earlier,
before we actually reached the overflow threshold, when we have to
throttle new allocations. We can also do it without taking global
arc_evict_lock, reducing the contention.
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12279
Callers of zfs_file_get and zfs_file_put can corrupt the reference
counts for the file structure resulting in a panic or a soft lockup.
When zfs send/recv runs, it will add a reference count to the
open file, and begin to send or recv the stream. If the file descriptor
is closed, then when dmu_recv_stream() or dmu_send() return we will
call zfs_file_put to remove the reference we placed on the file
structure. Unfortunately, because zfs_file_put() uses the file
descriptor to lookup the file structure, it may end up finding that
the file descriptor table no longer contains the file struct, thus
leaking the file structure. Or it might end up finding a file
descriptor for a different file and blindly updating its reference
counts. Other failure modes probably exists.
This change reworks the zfs_file_[get|put] interface to not rely
on the file descriptor but instead pass the zfs_file_t pointer around.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-issue: DLPX-76119
Closes#12299
Many FreeBSD disk drivers support "unmapped" I/O mode, when data
buffer represented not with a virtually contiguous KVA-mapped address
range, but with a list of physical memory pages. Originally it was
designed to do I/O from buffers without KVA mapping (unmapped). But
moving virtual addresses out of equation allows us to operate even
non-contiguous data buffers with one condition: all buffer discon-
tinuities must be aligned to memory page borders.
Doing I/O to capable GEOM device this patch traverses through non-
linear ABD buffers, validating the chunks borders. If the condition
is met, it supplies GEOM with the list of original physical memory
pages instead of copying the data into temporary contiguous buffer.
On capable hardware on pools with ashift=12 and default ABD chunk of
4KB it should handle all the I/O without additional memory copying.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12320
It makes no sense to set it below PAGE_SIZE, since it increases all
overheads and makes returning memory to OS problematic. It makes no
sense to set it above PAGE_SIZE, since such allocations and especially
frees are too expensive and cause KVA fragmentation to benefit from
fewer chunks. After that it makes no sense to keep more complicated
math here.
What may have sense though is just a tunable border between linear and
scatter ABDs, previously also controlled by this tunable. Retain that
functionality by taking abd_scatter_min_size tunable from Linux, just
with different default value.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12328
This dramatically reduces the lock contention on systems with slower
(non-TSC) timecounters. With TSC the difference is minimal, but since
this lock is pretty congested, any improvement counts. Plus I don't
see any reason to do it under the lock other than the latency of the
lock itself, which this change actually reduces.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12281
This field is used only by illumos mdb. On other platforms it only
increases the struct size from 32 to 40 bytes. For struct vdev_queue
including 13 instances of avl_tree_t size means active cache lines.
Keep the padding in user-space for now to not break the ABI.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12290
With default dbuf cache size of 1/32 of ARC, it makes no sense to have
hash table of the same size (or even bigger on Linux). Reduce it to
1/8 of ARC's one, still leaving some slack, assuming higher I/O rate
via dbuf cache than via ARC.
Remove padding from ARC hash locks array. The idea behind padding
is to avoid false sharing between locks. It would have sense if
there would be a limited number of very busy locks. But since we
have no limit on the number, using the same memory for more locks we
can achieve even lower lock contention with the same false sharing,
or we can use less memory for the same contention level.
Reduce number of hash locks from 8192 to 2048. The number is still
big enough to not cause contention, but reduced memory size improves
cache hit rate for mutex_tryenter() in ARC eviction thread, saving
about 1% of the thread time.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12289
Fix a leak of abd_t that manifested mostly when using
raidzN with at least as many columns as N (e.g. a
four-disk raidz2 but not a three-disk raidz2).
Sufficiently heavy raidz use would eventually run a system
out of memory.
Additionally:
* Switch abd_cache arena to FIRSTFIT, which empirically
improves perofrmance.
* Make abd_chunk_cache more performant and debuggable.
* Allocate the abd_zero_buf from abd_chunk_cache rather
than the heap.
* Don't try to reap non-existent qcaches in abd_cache arena.
* KM_PUSHPAGE->KM_SLEEP when allocating chunks from their
own arena
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Co-authored-by: Sean Doran <smd@use.net>
Closes#12295
dmu_zfetch_stream_fini() is missing calls to destroy the refcounts,
leaking them and the mutex inside.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#12294
Use dp_dirty_pertxg[] for txg_kick(), instead of dp_dirty_total in
original code. Extra parameter "txg" is added for txg_kick(), thus it
knows which txg to kick. Also txg_kick() call is moved from
dsl_pool_need_dirty_delay() to dsl_pool_dirty_space() so that we can
know the txg number assigned for txg_kick().
Some unnecessary code regarding dp_dirty_total in txg_sync_thread() is
also cleaned up.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: jxdking <lostking2008@hotmail.com>
Closes#12274
The only reason for spa_config_*() to use refcount instead of simple
non-atomic (thanks to scl_lock) variable for scl_count is tracking,
hard disabled for the last 8 years. Switch to simple int scl_count
reduces the lock hold time by avoiding atomic, plus makes structure
fit into single cache line, reducing the locks contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12287
LLVM's Polly (ISL to be precise) is unhappy with the loop from
ddt_stat_add():
CC [M] fs/zfs/zfs/ddt.o
../lib/External/isl/isl_schedule_node.c:2470: cannot insert node
between set or sequence node and its filter children
(building with the custom patch which adds Polly support to Kbuild)
The mentioned loop is rather suboptimal. All that we need is to just
treat ddt_stat_t as an array of u64 and perform 1:1 addition or
substraction. This can be done in simpler for-loop with the
determined index and bounds. Compiler will expand d_end - d into
a number of ddt_stat_t fields at compile time.
This prevents Polly from failing on this file.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Closes#12253
The number of sublists in a multilist is relatively small. We dont need
64 bits to calculate an index. 32 bits is sufficient and makes the
code more efficient.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12288
The stock zstd code expects some helpers from ASAN if present.
This works fine in userland, but in kernel, KASAN also gets detected,
and lacks those helpers. So let's make some empty substitutes for
that case.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12232
While abd_verify() does nothing when built without debug, compiler
can't optimize it out by itself due to calls to external list_*()
and abd_verify_scatter(). This commit makes it explicit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12280
Unlike most other properties the 'compatibility' property is stored
in the pool config object and not the DMU_OT_POOL_PROPS object.
This had the advantage that the compatibility information is available
without needing to fully import the pool (it can be read with zdb).
However, this means we need to make sure to update both the copy of
the config in the MOS and the cache file. This wasn't being done.
This commit adds a call to spa_async_request() to ensure the copy of
the config in the cache file gets updated as well as the one stored
in the pool. This same change is made for the 'comment' property
which suffers from the same inconsistency.
Reviewed-by: Sean Eric Fagan <sef@ixsystems.com>
Reviewed-by: Colm Buckley <colm@tuatha.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12261Closes#12276
According to current zfs man page zfs_metaslab_mem_limit should be
25 instead of 75.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: jumbi77@users.noreply.github.comCloses#12273
Compiling with gcc 11.1.0 produces three new warnings.
Change the code slightly to avoid them.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#12130Closes#12188Closes#12237
ZFS loves using %llu for uint64_t, but that requires a cast to not
be noisy - which is even done in many, though not all, places.
Also a couple places used %u for uint64_t, which were promoted
to %llu.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12233
This reverts commit 13fac09868.
Per the discussion in #11531, the reverted commit---which intended only
to be a cleanup commit---introduced a subtle, unintended change in
behavior.
Care was taken to partially revert and then reapply 10b3c7f5e4
which would otherwise have caused a conflict. These changes were
squashed in to this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Suggested-by: @chrisrd
Suggested-by: robn@despairlabs.com
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11531Closes#12227
In all places except two spa_get_random() is used for small values,
and the consumers do not require well seeded high quality values.
Switch those two exceptions directly to random_get_pseudo_bytes()
and optimize spa_get_random(), renaming it to random_in_range(),
since it is not related to SPA or ZFS in general.
On FreeBSD directly map random_in_range() to new prng32_bounded() KPI
added in FreeBSD 13. On Linux and in user-space just reduce the type
used to uint32_t to avoid more expensive 64bit division.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12183
wmsum was designed exactly for cases like these with many updates
and rare reads. It allows to completely avoid atomic operations on
congested global variables.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12172
In case we have I/O and try to remove an L2ARC device a deadlock might
occur. arc_read()->zio_read()->zfs_blkptr_verify() waits for SCL_VDEV
to be dropped while holding the hash_lock. However, spa_l2cache_load()
holds SCL_ALL and waits for the hash_lock in l2arc_evict().
Fix this by moving zfs_blkptr_verify() to the top top arc_read() before
the hash_lock is taken. Verify the block pointer and return a checksum
error if damaged rather than halting the system, by using
BLK_VERIFY_LOG instead of BLK_VERIFY_HALT.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#12054
vdev_draid_min_asize() returns the minimum size of a child vdev. This
is used when determining if a disk is big enough to replace a child.
It's also used by zdb to determine how big of a child to make to test
replacement.
vdev_draid_min_asize() says that the child’s asize has to be at least
1/Nth of the entire draid’s asize, which is the same logic as raidz.
However, this contradicts the code in vdev_draid_open(), which
calculates the draid’s asize based on a reduced child size:
An additional 32MB of scratch space is reserved at the end of each
child for use by the dRAID expansion feature
So the problem is that you can replace a draid disk with one that’s
vdev_draid_min_asize(), but it actually needs to be larger to accommodate
the additional 32MB. The replacement is allowed and everything works at
first (since the reserved space is at the end, and we don’t try to use
it yet), but when you try to close and reopen the pool,
vdev_draid_open() calculates a smaller asize for the draid, because of
the smaller leaf, which is not allowed.
I think the confusion is that vdev_draid_min_asize() is correctly
returning the amount of required *allocatable* space in a leaf, but the
actual *size* of the leaf needs to be at least 32MB more than that.
ztest_vdev_attach_detach() assumes that it can attach that size of
device, and it actually can (the kernel/libzpool accepts it), but it
then later causes zdb to not be able to open the pool.
This commit changes vdev_draid_min_asize() to return the required size
of the leaf, not the size that draid will make available to the metaslab
allocator.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11459Closes#12221
In zfs_znode_alloc we always hash inodes. If the
znode is unlinked, we do not need to hash it. This
fixes the problem where zfs_suspend_fs is doing zrele
(iput) in an async fashion, and zfs_resume_fs unlinked
drain processing will try to hash an inode that could
still be hashed, resulting in a panic.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alan Somers <asomers@gmail.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#9741Closes#11223Closes#11648Closes#12210
This commit partially reverts changes to multilists in PR 7968
(multi-threaded spa-sync()) and adds some cache line alignments to
separate read-only multilists and heavily modified refcount's to different
cache lines.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-by: iXsystems, Inc.
Closes#12158
This mostly reverts "3537 want pool io kstats" commit of 8 years ago.
From one side this code using pool-wide locks became pretty bad for
performance, creating significant lock contention in I/O pipeline.
From another, there are more efficient ways now to obtain detailed
statistics, while this statistics is illumos-specific and much less
usable on Linux and FreeBSD, reported only via procfs/sysctls.
This commit does not remove KSTAT_TYPE_IO implementation, that may
be removed later together with already unused KSTAT_TYPE_INTR and
KSTAT_TYPE_TIMER.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12212
`getfsstat(2)` is used to retrieve the list of mounted file systems,
which libzfs uses when fetching properties like mountpoint, atime,
setuid, etc. The `mode` parameter may be `MNT_NOWAIT`, which uses
information in the VFS's cache, or `MNT_WAIT`, which effectively does a
`statfs` on every single mounted file system in order to fetch the most
up-to-date information. As far as I can tell, the only fields that
libzfs cares about are the filesystem's name, mountpoint, fstypename,
and mount flags. Those things are always updated on mount and unmount,
so they will always be accurate in the VFS's mount cache except in two
circumstances:
1) When a file system is busy unmounting
2) When a ZFS file system changes the value of a mount-overridable
property like atime or setuid, but doesn't remount the file system.
Right now that only happens when the property is changed by an
unprivileged user who has delegated authority to change the property
but not to mount the dataset. But perhaps libzfs could choose to do
it for other reasons in the future.
Switching to `MNT_NOWAIT` will greatly improve speed with no downside,
as long as we explicitly update the mount cache whenever we change a
mount-overridable property.
For comparison, Illumos gets this information using the native
`getmntany` and `getmntent` functions, which also use cached
information. The illumos function that would refresh the cache,
`resetmnttab`, is never called by libzfs.
And on GNU/Linux, `getmntany` and `getmntent` don't even communicate
with the kernel directly. They simply parse the file they are given,
which is usually /etc/mtab or /proc/mounts. Perhaps the implementation
of /proc/mounts is synchronous, ala MNT_WAIT; I don't know.
Sponsored-by: Axcient
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes: #12091
Update the logic to handle the dedup-case of consecutive
FREEs in the livelist code. The logic still ensures that
all the FREE entries are matched up with a respective
ALLOC by keeping a refcount for each FREE blkptr that we
encounter and ensuring that this refcount gets to zero
by the time we are done processing the livelist.
zdb -y no longer panics when encountering double frees
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: John Kennedy <john.kennedy@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11480Closes#12177
- Avoid atomic_add() when updating as_lower_bound/as_upper_bound.
Previous code was excessively strong on 64bit systems while not
strong enough on 32bit ones. Instead introduce and use real
atomic_load() and atomic_store() operations, just an assignments
on 64bit machines, but using proper atomics on 32bit ones to avoid
torn reads/writes.
- Reduce number of buckets on large systems. Extra buckets not as
much improve add speed, as hurt reads. Unlike wmsum for aggsum
reads are still important.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12145
VFS_QUOTACTL(9) has been updated to allow each filesystem to indicate
whether it has changed the busy state of the mount. The filesystem
may still assume that its .vfs_quotactl entrypoint is always called
with the mount busied, but only needs to unbusy the mount (and clear
*mp_busy) if it does something that actually requires the mount to be
unbusied. It no longer needs to blindly copy-paste the UFS protocol
for calling vfs_unbusy(9) for the Q_QUOTAOFF and Q_QUOTAON commands.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jason Harmening <jason.harmening@gmail.com>
Closes#12052
For small objects the kernel's slab implementation is very fast and
space efficient. However, as the allocation size increases to
require multiple pages performance suffers. The SPL kmem cache
allocator was designed to better handle these large allocation
sizes. Therefore, on Linux the kmem_cache_* compatibility wrappers
prefer to use the kernel's slab allocator for small objects and
the custom SPL kmem cache allocator for larger objects.
This logic was effectively disabled for all architectures using
a non-4K page size which caused all kmem caches to only use the
SPL implementation. Functionally this is fine, but the SPL code
which calculates the target number of objects per-slab does not
take in to account that __vmalloc() always returns page-aligned
memory. This can result in a massive amount of wasted space when
allocating tiny objects on a platform using large pages (64k).
To resolve this issue we set the spl_kmem_cache_slab_limit cutoff
to 16K for all architectures.
This particular change does not attempt to update the logic used
to calculate the optimal number of pages per slab. This remains
an issue which should be addressed in a future change.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12152Closes#11429Closes#11574Closes#12150
Both were removed in 4fbdb10c7b ("remove
kmem_cache module parameter KMC_EXPIRE_AGE")
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#12157
The additional iter advance is incorrect, as copy_from_iter() has
already done the right thing. This will result in the following
warning being printed to the console as of the 5.12 kernel.
Attempted to advance past end of bvec iter
This change should have been included with #11378 when a
similar change was made on the read side.
Suggested-by: @siebenmann
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Issue #11378Closes#12041Closes#12155
wmsum counters are a reduced version of aggsum counters, optimized for
write-mostly scenarios. They do not provide optimized read functions,
but instead allow much cheaper add function. The primary usage is
infrequently read statistic counters, not requiring exact precision.
The Linux implementation is directly mapped into percpu_counter KPI.
The FreeBSD implementation is directly mapped into counter(9) KPI.
In user-space due to lack of better implementation mapped to aggsum.
Unfortunately neither Linux percpu_counter nor FreeBSD counter(9)
provide sufficient functionality to completelly replace aggsum, so
it still remains to be used for several hot counters.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12114
Previously, ZFS scaled maxinflight_bytes based on total number of
disks in the pool. A 3-wide mirror was receiving a queue depth of 3
disks, which it should not, since it reads from all the disks inside.
For wide raidz the situation was slightly better, but still a 3-wide
raidz1 received a depth of 3 disks instead of 2.
The new code counts only unique data disks, i.e. 1 disk for mirrors
and non-parity disks for raidz/draid. For draid the math is still
imperfect, since vdev_get_nparity() returns number of parity disks
per group, not per vdev, but still some better than it was.
This should slightly reduce scrub influence on payload for some pool
topologies by avoiding excessive queuing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closing #12046
Just like #12087, the set_acl signature changed with all the bolted-on
*userns parameters, which disabled set_acl usage, and caused #12076.
Turn zpl_set_acl into zpl_set_acl and zpl_set_acl_impl, and add a
new configure test for the new version.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12076Closes#12093
Previous commit added accounting for geom mode, but not for dev.
In geom mode we actually have GEOM statistics, while in dev mode
additional accounting actually makes more sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12097
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#12049
I looked for a bit, and couldn't find any documentation on
how to print all logged dbgmsg entries, just messages since
the DTrace probe started, until @allanjude kindly pointed me
toward the sysctl.
So let's add that note where the DTrace probe is mentioned for
FreeBSD, so other people can find it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes#12113
Propagate vdev child state to parents on invalid label
Add VDEV_AUX_BAD_LABEL to print_import_config()
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Co-authored-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Signed-off-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Closes#12088
ZFS does not expect transient errors from crypto. For read they are
counted as checksum errors, while for write end up in panic. To not
panic on random low memory conditions retry ENOMEM errors in the OCF
wrapper function.
While there remove unneeded timeout and priority from msleep().
External-issue: https://reviews.freebsd.org/D30339
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#12077
Linux changed the tmpfile() signature again in torvalds/linux@6521f89,
which in turn broke our HAVE_TMPFILE detection in configure.
Update that macro to include the new case, and change the signature of
zpl_tmpfile as appropriate.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rich Ercolani <rincebrain@gmail.com>
Closes: #12060Closes: #12087
This change addresses two distinct scenarios which are possible
when performing a sequential resilver to a dRAID pool with vdevs
that contain silent unknown damage. Which in this circumstance
took the form of the devices being intentionally overwritten with
zeros. However, it could also result from a device returning incorrect
data while a sequential resilver was in progress.
Scenario 1) A sequential resilver is performed while all of the
dRAID vdevs are ONLINE and there is silent damage present on the
vdev being resilvered. In this case, nothing will be repaired
by vdev_raidz_io_done_reconstruct_known_missing() because
rc->rc_error isn't set on any of the raid columns. To address
this vdev_draid_io_start_read() has been updated to always mark
the resilvering column as ESTALE for sequential resilver IO.
Scenario 2) Multiple columns contain silent damage for the same
block and a sequential resilver is performed. In this case it's
impossible to generate the correct data from parity unless all of
the damaged columns are being sequentially resilvered (and thus
only good data is used to generate parity). This is as expected
and there's nothing which can be done about it. However, we need
to be careful not to make to situation worse. Since we can't
verify the data is actually good without a checksum, we must
only repair the devices which are being sequentially resilvered.
Otherwise, an incorrect repair to a device which previously
contained good data could effectively lock in the damage and
make reconstruction impossible. A check for this was added to
vdev_raidz_io_done_verified() along with a new test case.
Lastly, this change updates the redundancy_draid_spare1 and
redundancy_draid_spare3 test cases to be more representative
of normal dRAID replacement operation. Specifically, what we
care about is that the scrub run after a sequential resilver
does not find additional blocks which need repair. This would
indicate the sequential resilver failed to rebuild a section of
one of the devices. Note also the tests were switched to using
the verify_pool() function which still checks for checksum errors.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12061
While use of dynamic taskqs allows to reduce number of idle threads,
hardcoded 8 taskqs of each kind is a big overkill for small systems,
complicating CPU scheduling, increasing I/O reorder, etc, while
providing no real locking benefits, just not needed there.
On another side, 12*8 worker threads per kind are able to overload
almost any system nowadays. For example, pool of several fast SSDs
with SHA256 checksum makes system barely responsive during scrub, or
with dedup enabled barely responsive during large file deletion.
To address both problems this patch introduces ZTI_SCALE macro, alike
to ZTI_BATCH, but with multiple taskqs, depending on number of CPUs,
to be used in places where lock scalability is needed, while request
ordering is not so much. The code is made to create new taskq for
~6 worker threads (less for small systems, but more for very large)
up to 80% of CPU cores (previous 75% was not good for rounding down).
Both number of threads and threads per taskq are now tunable in case
somebody really wants to use all of system power for ZFS.
While obviously some benchmarks show small peak performance reduction
(not so big really, especially on systems with SMT, where use of the
second threads does not give as much performance as the first ones),
they also show dramatic latency reduction and much more smooth user-
space operation in case of high CPU usage by ZFS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11966
Use dsl_dataset_has_resume_receive_state()
not dsl_dataset_is_zapified() to check if
stream is resumable.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Alek Pinchuk <apinchuk@axcient.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#12034
FreeBSD historically has not cared about the xattr property; it was
always treated as xattr=on. With xattr=on, xattrs are stored as files
in a hidden xattr directory. With xattr=sa, xattrs are stored as
system attributes and get cached in nvlists during xattr operations.
This makes SA xattrs simpler and more efficient to manipulate. FreeBSD
needs to implement the SA xattr operations for feature parity with
Linux and to ensure that SA xattrs are accessible when migrated or
replicated from Linux.
Following the example set by Linux, refactor our existing extattr vnops
to split off the parts handling dir style xattrs, and add the
corresponding SA handling parts.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11997
Commit d1d4769 takes into account the encryption key version to
decide if the local_mac could be zeroed out. However, this could lead
to failure mounting encrypted datasets created with intermediate
versions of ZFS encryption available in master between major releases.
In order to prevent this situation revert d1d4769 pending a more
comprehensive fix which addresses the mount failure case.
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #11294
Issue #12025
Issue #12300Closes#12033
Add support for http and https to the keylocation properly to
allow encryption keys to be fetched from the specified URL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #9543Closes#9947Closes#11956
Linux kernel commit 0f00b82e5413571ed225ddbccad6882d7ea60bc7 removes the
revalidate_disk() handler from struct block_device_operations. This
caused a regression, and this commit eliminates the call to it and the
assignment in the block_device_operations static handler assignment
code, when configure identifies that the kernel doesn't support that
API handler.
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11967Closes#11977
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11972
zfs_zevent_console committed multiple printk()s per line without
properly continuing them ‒ a single event could easily be fragmented
across over thirty lines, making it useless for direct application
zfs_zevent_cols exists purely to wrap the output from zfs_zevent_console
The niche this was supposed to fill can be better served by something
akin to the all-syslog ZEDLET
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#7082Closes#11996
When dRAID performs a normal read operation only the data columns
in the raid map are read from disk. This is enough information to
calculate the checksum, verify it, and return the needed data to the
application. It's only in the event of a checksum failure that the
additional parity and any empty columns must be read since they are
required for parity reconstruction.
Reading these additional columns is handled by vdev_raidz_read_all()
which calls vdev_draid_map_alloc_empty() to expand the raid_map_t
and submit IOs for the missing columns. This all works correctly,
but it fails to account for any "short" columns. These are data
columns which are padded with a empty skip sector at the end.
Since that empty sector is not needed for a normal read it's not
read when columns is first read from disk. However, like the parity
and empty columns the skip sector is needed to perform reconstruction.
The fix is to mark any "short" columns as never being read by clearing
the rc_tried flag when expanding the raid_map_t. This will cause
the entire column to re-read from disk in the event of a checksum
failure allowing the self-healing functionality to repair the block.
Note that this only effects the self-healing feature because when
scrubbing a pool the parity, data, and empty columns are all read
initially to verify their contents. Furthermore, only blocks which
contain "short" columns would be effected, and only when the memory
backing the skip sector wasn't already zeroed out.
This change extends the existing redundancy_raidz.ksh test case to
verify self-healing (as well as resilver and scrub). Then applies
the same test case to dRAID with a slightly modified version of
the test script called redundancy_draid.ksh. The unused variable
combrec was also removed from both test cases.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#12010
Afterward, git grep ZoL matches:
* README.md: * [ZoL Site](https://zfsonlinux.org)
- Correct
* etc/default/zfs.in:# ZoL userland configuration.
- Changing this would induce a needless upgrade-check,
if the user has modified the configuration;
this can be updated the next time the defaults change
* module/zfs/dmu_send.c: * ZoL < 0.7 does not handle [...]
- Before 0.7 is ZoL, so fair enough
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Issue #11956
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11994
zfs_log_create returns void, so there is no reason to cast its return
value to void at the call site.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11994
Quoting <linux/exportfs.h>:
> encode_fh() should return the fileid_type on success and on error
> returns 255 (if the space needed to encode fh is greater than
> @max_len*4 bytes). On error @max_len contains the minimum size (in 4
> byte unit) needed to encode the file handle.
ZFS was not setting max_len in the case where the handle was too
small. As a result of this, the `t_name_to_handle_at.c' example in
name_to_handle_at(2) did not work on ZFS.
zfsctl_fid() will itself set max_len if called with a fid that is too
small, so if we give zfs_fid() that behavior as well, the fix is quite
easy: if the handle is too small, just use a zero-size fid instead of
the handle.
Tested by running t_name_to_handle_at on a normal file, a directory, a
.zfs directory, and a snapshot.
Thanks-to: Puck Meerburg <puck@puckipedia.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Closes#11995
Previous code tried to keep prefetch streams while moving dnode. But
it was at least not updating per-stream zs_fetchback pointers, causing
use-after-free on next access. Instead of that I see much easier and
cleaner to just drop old prefetch state and start new from scratch.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11936Closes#11998
zp->z_lock is used in shared code for protecting projid and scantime.
We don't exercise these paths much if at all on FreeBSD, so have been
lucky enough not to have issues with the uninitialized locks so far.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#12003
Remove some extra whitespace.
Use pointer-typed asserts in Linux's znode cache destructor for more
info when debugging.
Simplify a couple of conversions from inode to znode when we already
have the znode.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11974
Convert use of ASSERT() to ASSERT0(), ASSERT3U(), ASSERT3S(),
ASSERT3P(), and likewise for VERIFY(). In some cases it ended up
making more sense to change the code, such as VERIFY on nvlist
operations that I have converted to use fnvlist instead. In one
place I changed an internal struct member from int to boolean_t to
match its use. Some asserts that combined multiple checks with &&
in a single assert have been split to separate asserts, to make it
apparent which check fails.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11971
IS_XATTRDIR is never used.
v_count is only used in two places, one immediately followed by the
use of the real name, v_usecount.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@ixsystems.com>
Closes#11973
This ensures that we don't accumulate checksum errors against offline or
unavailable devices but, more importantly, means that we don't
needlessly create DTL entries for offline devices that are already
up-to-date.
Consider a 3-way mirror, with disk A always online (and so always with
an empty DTL) and B and C only occasionally online. When A & B resilver
with C offline, B's DTL will effectively be appended to C's due to these
spurious ZIOs even as the resilver empties B's DTL:
* These ZIOs land in vdev_mirror_scrub_done() and flag an error
* That flagged error causes vdev_mirror_io_done() to see
unexpected_errors, so it issues a ZIO_TYPE_WRITE repair ZIO, which
inherits ZIO_FLAG_SCAN_THREAD because zio_vdev_child_io() includes
that flag in ZIO_VDEV_CHILD_FLAGS.
* That ZIO fails, too, and eventually zio_done() gets its hands on it
and calls vdev_stat_update().
* vdev_stat_update() sees the error and this zio...
* is not speculative,
* is not due to EIO (but rather ENXIO, since the device is closed)
* has an ->io_vd != NULL (specifically, the offline leaf device)
* is a write
* is for a txg != 0 (but rather the read block's physical birth txg)
* has ZIO_FLAG_SCAN_THREAD asserted
* So: vdev_stat_update() calls vdev_dtl_dirty() on the offline vdev.
Then, when A & C resilver with B offline, that story gets replayed and
C's DTL will be appended to B's.
In fact, one does not need this permanently-broken-mirror scenario to
induce badness: breaking a mirror with no DTLs and then scrubbing will
create DTLs for all offline devices. These DTLs will persist until the
entire mirror is reassembled for the duration of the *resilver*, which,
incidentally, will not consider the devices with good data to be sources
of good data in the case of a read failure.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Closes#11930
This obeys the change in freebsd/freebsd-src@bce7ee9d4
External-issue: https://reviews.freebsd.org/D26980
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11947
Introduce a specific valid function for avx512f+avx512bw (instead
of checking only for avx512f).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Romain Dolbeau <romain@dolbeau.org>
Closes#11937Closes#11938
Objtool requires the use of a DRAP register while aligning the
stack. Since a DRAP register is a gcc concept and we are
notoriously low on registers in the crypto code, it's not worth
the effort to mimic gcc generated stack realignment.
We simply silence the warning by adding the offending object files
to OBJECT_FILES_NON_STANDARD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#6950Closes#11914
This deduplicates 2 sets of caches which use the same allocation size.
Memory savings fluctuate a lot, one sample result is FreeBSD running
"make buildworld" saving ~180MB RAM in reduced page count associated
with zio caches.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11877
Since the assembly routines calculating SHA checksums don't use
a standard stack layout, CFI directives are needed to unroll the
stack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11733
Fix NULL pointer dereference when reporting
checksum error for gang block in zio_done.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Zuchowski <pzuchowski@datto.com>
Closes#11872Closes#11896
This fixes /proc/sys/kernel/spl/hostid on kernels with mainline commit
32927393dc1ccd60fb2bdc05b9e8e88753761469 ("sysctl: pass kernel pointers
to ->proc_handler") ‒ 5.7-rc1 and up
The access_ok() check in copy_to_user() in proc_copyout_string() would
always fail, so all userspace reads and writes would fail with EINVAL
proc_dostring() strips only the final new-line,
but simple_strtoul() doesn't actually need a back-trimmed string ‒
writing "012345678 \n" is still allowed, as is "012345678zupsko", &c.
This alters what happens when an invalid value is written ‒
previously it'd get set to what-ever simple_strtoul() returned
(probably 0, thereby resetting it to default), now it does nothing
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ahelenia Ziemiańska <nabijaczleweli@nabijaczleweli.xyz>
Closes#11878Closes#11879
Traversal code, traverse_visitbp() does visit blocks recursively.
Indirect (Non L0) Block of size 128k could contain, 1024 block pointers
of 128 bytes. In case of full traverse OR incremental traverse, where
all blocks were modified, it could traverse large number of blocks
pointed by indirect. Traversal code does issue prefetch of blocks
traversed below indirect. This could result into large number of
async reads queued on vdev queue. So, account for prefetch issued for
blocks pointed by indirect and limit max prefetch in one go.
Module Param:
zfs_traverse_indirect_prefetch_limit: Limit of prefetch while traversing
an indirect block.
Local counters:
prefetched: Local counter to account for number prefetch done.
pidx: Index for which next prefetch to be issued.
ptidx: Index at which next prefetch to be triggered.
Keep "ptidx" somewhere in the middle of blocks prefetched, so that
blocks prefetch read gets the enough time window before their demand
read is issued.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Jitendra Patidar <jitendra.patidar@nutanix.com>
Closes#11802Closes#11803
This change adds SIGSTOP and SIGTSTP handling to the issig function;
this mirrors its behavior on Solaris. This way, long running kernel
tasks can be stopped with the appropriate signals. Note that doing
so with ctrl-z on the command line doesn't return control of the tty
to the shell, because tty handling is done separately from stopping
the process. That can be future work, if people feel that it is a
necessary addition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Issue #810
Issue #10843Closes#11801
It happens to trip over an assert but does not matter for correctness at
this time. Done for future proofing.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11884
It's been observed in the CI that the required 25% of obsolete bytes
in the mapping can be to high a threshold for this test resulting in
condensing never being triggered and a test failure. To prevent these
failures make the existing zfs_condense_indirect_obsolete_pct tuning
available so the obsolete percentage can be reduced from 25% to 5%
during this test.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11869
After 3937ab20f zfsdev_get_state_impl can become zfsdev_get_state.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11833
SMACK needs to have the ZFS dentry security field setup before
SMACK's d_instantiate() hook is called as it requires functioning
'__vfs_getxattr()' calls to properly set the labels.
Fxes:
1) file instantiation properly setting the object label to the
subject's label
2) proper file labeling in a transmutable directory
Functions Updated:
1) zpl_create()
2) zpl_mknod()
3) zpl_mkdir()
4) zpl_symlink()
External-issue: https://github.com/cschaufler/smack-next/issues/1
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: TerraTech <TerraTech@users.noreply.github.com>
Closes#11646Closes#11839
When a rebuild completes it will automatically schedule a follow up
scrub to verify all of the block checksums. Before setting up the
scrub execute the counterpart dsl_scan_setup_check() function to
confirm the scrub can be started. Prior to this change we'd only
check vdev_rebuild_active() which isn't as comprehensive, and using
the check function keeps all of this logic in one place.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11849
Just as delay zevents can flood the zevent pipe when a vdev becomes
unresponsive, so do the deadman zevents.
Ratelimit deadman zevents according to the same tunable as for delay
zevents.
Enable deadman tests on FreeBSD and add a test for deadman event
ratelimiting.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Don Brady <don.brady@delphix.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11786
`kmem_alloc(size>PAGESIZE, KM_SLEEP)` is backed by `kmalloc()`, which
finds contiguous physical memory. If there isn't enough contiguous
physical memory available (e.g. due to physical page fragmentation), the
OOM killer will be invoked to make more memory available. This is not
ideal because processes may be killed when there is still plenty of free
memory (it just happens to be in individual pages, not contiguous runs
of pages). We have observed this when allocating the ~13KB `zfs_cmd_t`,
for example in `zfsdev_ioctl()`.
This commit changes the behavior of
`kmem_alloc(size>PAGESIZE, KM_SLEEP)` when there are insufficient
contiguous free pages. In this case we will find individual pages and
stitch them together using virtual memory. This is accomplished by
using `kvmalloc()`, which implements the described behavior by trying
`kmalloc(__GFP_NORETRY)` and falling back on `vmalloc()`.
The behavior of `kmem_alloc(KM_NOSLEEP)` is not changed; it continues to
use `kmalloc(GPF_ATOMIC | __GFP_NORETRY)`. This is because `vmalloc()`
may sleep.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11461
Correct an assortment of typos throughout the code base.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11774
We have exclusive access to our zfsdev state object in this section
until it is invalidated by setting zs_minor to -1, so we can destroy
the state without taking a lock if we do the invalidation last, after
a member to ensure correct ordering.
While here, strengthen the assertions that zs_minor is valid when we
enter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11751
Nothing bad happens if a prefix of your pool name matches a disk name.
This is a bit of a silly restriction at this point.
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11781Closes#11813
The lower bound for this scaling to too low and the upper bound is too
high. Use a fixed default length of 512 instead, which is a reasonable
value on any system.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11822
ratelimit_dropped isn't protected by a lock and is expected to
be updated atomically.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11822
For gang blocks, `DVA_GET_ASIZE()` is the total space allocated for the
gang DVA including its children BP's. The space allocated at each DVA's
vdev/offset is `vdev_psize_to_asize(vd, SPA_GANGBLOCKSIZE)`.
This commit makes this relationship more clear by using a helper
function, `vdev_gang_header_asize()`, for the space allocated at the
gang block's vdev/offset.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11744
Other (all?) Linux filesystems seem to return -EPERM instead of -EACCESS
when trying to set FS_APPEND_FL or FS_IMMUTABLE_FL without the
CAP_LINUX_IMMUTABLE capability. This was detected by generic/545 test
in the fstest suite.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Luis Henriques <henrix@camandro.org>
Closes#11791
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Closes#11775
To make better predictions on parallel workloads dmu_zfetch() should
be called as early as possible to reduce possible request reordering.
In particular, it should be called before dmu_buf_hold_array_by_dnode()
calls dbuf_hold(), which may sleep waiting for indirect blocks, waking
up multiple threads same time on completion, that can significantly
reorder the requests, making the stream look like random. But we
should not issue prefetch requests before the on-demand ones, since
they may get to the disks first despite the I/O scheduler, increasing
on-demand request latency.
This patch splits dmu_zfetch() into two functions: dmu_zfetch_prepare()
and dmu_zfetch_run(). The first can be executed as early as needed.
It only updates statistics and makes predictions without issuing any
I/Os. The I/O issuance is handled by dmu_zfetch_run(), which can be
called later when all on-demand I/Os are already issued. It even
tracks the activity of other concurrent threads, issuing the prefetch
only when _all_ on-demand requests are issued.
For many years it was a big problem for storage servers, handling
deeper request queues from their clients, having to either serialize
consequential reads to make ZFS prefetcher usable, or execute the
incoming requests as-is and get almost no prefetch from ZFS, relying
only on deep enough prefetch by the clients. Benefits of those ways
varied, but neither was perfect. With this patch deeper queue
sequential read benchmarks with CrystalDiskMark from Windows via
iSCSI to FreeBSD target show me much better throughput with almost
100% prefetcher hit rate, comparing to almost zero before.
While there, I also removed per-stream zs_lock as useless, completely
covered by parent zf_lock. Also I reused zs_blocks refcount to track
zf_stream linkage of the stream, since I believe previous zs_fetch ==
NULL check in dmu_zfetch_stream_done() was racy.
Delete prefetch streams when they reach ends of files. It saves up
to 1KB of RAM per file, plus reduces searches through the stream list.
Block data prefetch (speculation and indirect block prefetch is still
done since they are cheaper) if all dbufs of the stream are already
in DMU cache. First cache miss immediately fires all the prefetch
that would be done for the stream by that time. It saves some CPU
time if same files within DMU cache capacity are read over and over.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11652
If TX_WRITE is create on a file, and the file is later deleted and a new
directory is created on the same object id, it is possible that when
zil_commit happens, zfs_get_data will be called on the new directory.
This may result in panic as it tries to do range lock.
This patch fixes this issue by record the generation number during
zfs_log_write, so zfs_get_data can check if the object is valid.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Chunwei Chen <david.chen@nutanix.com>
Closes#10593Closes#11682
Commit 235a85657 introduced a regression in evaluation of POSIX modes
that require group DENY entries in the internal ZFS ACL. An example
of such a POSX mode is 007. When write_implies_delete_child is set,
then ACE_WRITE_DATA is added to `wanted_dirperms` in prior to calling
zfs_zaccess_common(). This occurs is zfs_zaccess_delete().
Unfortunately, when zfs_zaccess_aces_check hits this particular DENY
ACE, zfs_groupmember() is checked to determine whether access should be
denied, and since zfs_groupmember() always returns B_TRUE on Linux and
so this check is failed, resulting ultimately in EPERM being returned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#11760
The FreeBSD boot loader relies on the bootfs property and is capable
of booting from removed (indirect) vdevs.
Reviewed-by Eric van Gyzen
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11763
It used to be required to pass a enum km_type to kmap_atomic() and
kunmap_atomic(), however this is no longer necessary and the wrappers
zfs_k(un)map_atomic removed these. This is confusing in the ABD code as
the struct abd_iter member iter_km no longer exists and the wrapper
macros simply compile them out.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11768
= Motivation
We've noticed several zloop crashes within Delphix generated
due to the following sequence of events:
- A device gets expanded and new metaslabas are allocated for
it. These metaslabs go through `metaslab_init()` but haven't
gone through `metaslab_sync_done()` yet. This meas that the
only range tree that's actually set is the `ms_allocatable`.
All the others are NULL.
- A vdev_initialization is issues and `vdev_initialize_thread`
starts processing one of these new metaslabs of the expanded
vdev.
- As part of `vdev_initialize_calculate_progress()` we call
into `metaslab_load()` and `metaslab_load_impl()` which
in turn tries to dereference the metaslabs trees that
are still NULL and therefore we crash.
The same failure can come up from the `vdev_trim` code paths.
= This Patch
We considered the following solutions to deal with this issue:
[A] Add logic to `vdev_initialize/trim` to skip those new
metaslabs. We decided against this as it would be good
to avoid exposing this lower-level detail to higer-level
operations.
[B] Have `metaslab_load_impl()` return early for new metaslabs
and thus never touch those range_trees that are NULL at
that time. This seemed more of a work-around for the bug
and not a clear-cut solution.
[C] Refactor our logic so all metaslabs have their range_trees
created at the time of their creatin in `metaslab_init()`.
In this patch we decided to go with [C] because:
(1) It doesn't expose more metaslab details to higher level
operations such as vdev initialize and trim.
(2) The current behavior of creating the range trees lazily
in `metaslab_sync_done()` is unnecessarily complicated.
(3) Always initializing the metaslab range_trees makes other
parts of the codebase cleaner. For example, we used to
use `ms_freed` as the reference value for knowing whether
all the range_trees have been initialized. Now we no
longer need to do that check in most places (and in the
few that we do we use the `ms_new` boolean field now
which is more readable).
= Side Changes
Probably due to a mismerge we set `ms_loaded` to `B_TRUE` twice
in `metasloab_load_impl()`. In this patch we remove the extraneous
assignment.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Closes#11737
The BIO_MAX_PAGES macro is being retired in favor of a bio_max_segs()
function that implements the typical MIN(x,y) logic used throughout the
kernel for bounding the allocation, and also the new implementation is
intended to be signed-safe (which the former was not).
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11765
In Linux 5.12, the filesystem API was modified to support ipmapped
mounts by adding a "struct user_namespace *" parameter to a number
functions and VFS handlers. This change adds the needed autoconf
macros to detect the new interfaces and updates the code appropriately.
This change does not add support for idmapped mounts, instead it
preserves the existing behavior by passing the initial user namespace
where needed. A subsequent commit will be required to add support
for idmapped mounted.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11712
The RAIDZ and DRAID code is responsible for reporting checksum errors on
their child vdevs. Checksum errors represent events where a disk
returned data or parity that should have been correct, but was not. In
other words, these are instances of silent data corruption. The
checksum errors show up in the vdev stats (and thus `zpool status`'s
CKSUM column), and in the event log (`zpool events`).
Note, this is in contrast with the more common "noisy" errors where a
disk goes offline, in which case ZFS knows that the disk is bad and
doesn't try to read it, or the device returns an error on the requested
read or write operation.
RAIDZ/DRAID generate checksum errors via three code paths:
1. When RAIDZ/DRAID reconstructs a damaged block, checksum errors are
reported on any children whose data was not used during the
reconstruction. This is handled in `raidz_reconstruct()`. This is the
most common type of RAIDZ/DRAID checksum error.
2. When RAIDZ/DRAID is not able to reconstruct a damaged block, that
means that the data has been lost. The zio fails and an error is
returned to the consumer (e.g. the read(2) system call). This would
happen if, for example, three different disks in a RAIDZ2 group are
silently damaged. Since the damage is silent, it isn't possible to know
which three disks are damaged, so a checksum error is reported against
every child that returned data or parity for this read. (For DRAID,
typically only one "group" of children is involved in each io.) This
case is handled in `vdev_raidz_cksum_finish()`. This is the next most
common type of RAIDZ/DRAID checksum error.
3. If RAIDZ/DRAID is not able to reconstruct a damaged block (like in
case 2), but there happens to be additional copies of this block due to
"ditto blocks" (i.e. multiple DVA's in this blkptr_t), and one of those
copies is good, then RAIDZ/DRAID compares each sector of the data or
parity that it retrieved with the good data from the other DVA, and if
they differ then it reports a checksum error on this child. This
differs from case 2 in that the checksum error is reported on only the
subset of children that actually have bad data or parity. This case
happens very rarely, since normally only metadata has ditto blocks. If
the silent damage is extensive, there will be many instances of case 2,
and the pool will likely be unrecoverable.
The code for handling case 3 is considerably more complicated than the
other cases, for two reasons:
1. It needs to run after the main raidz read logic has completed. The
data RAIDZ read needs to be preserved until after the alternate DVA has
been read, which necessitates refcounts and callbacks managed by the
non-raidz-specific zio layer.
2. It's nontrivial to map the sections of data read by RAIDZ to the
correct data. For example, the correct data does not include the parity
information, so the parity must be recalculated based on the correct
data, and then compared to the parity that was read from the RAIDZ
children.
Due to the complexity of case 3, the rareness of hitting it, and the
minimal benefit it provides above case 2, this commit removes the code
for case 3. These types of errors will now be handled the same as case
2, i.e. the checksum error will be reported against all children that
returned data or parity.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11735
Avoids tripping on asserts when doing pool recovery.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11739
The `rr_code` field in `raidz_row_t` is unused.
This commit removes the field, as well as the code that's used to set
it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11736
Don't handle (incorrectly) kmem_zalloc() failure. With KM_SLEEP,
will never return NULL.
Free the data allocated for non-virtual kstats when deleting the object.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11767
zhold() wraps igrab() on Linux, and igrab() may fail when the inode
is in the process of being deleted. This means zhold() must only be
called when a reference exists and therefore it cannot be deleted.
This is the case for all existing consumers so add a VERIFY and a
comment explaining this requirement.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#11704
To make use of zfs_refcount_held tunable it should be a module
parameter in open-zfs. Also, since the macros will auto-generate OS
specific tunables, removed the existing zfs_refcount_held reference
in module/os/freebsd/zfs/sysctl_os.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11753
Add parsing of the rewind options.
When I was upstreaming the change [1], I omitted the part where we
detect that the pool should be rewind. When the FreeBSD repo has
synced with the OpenZFS, this part of the code was removed.
[1] FreeBSD repo: 277f38abffc6a8160b5044128b5b2c620fbb970c
[2] OpenZFS repo: f2c027bd6a
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=254152
Originally reviewed by: tsoome, allanjude
Originally reviewed by: kevans (ok from high-level overview)
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11730
Resolve some oddities in zfsdev_close() which could result in a
panic and were not present in the equivalent function for Linux.
- Remove unused definition ZFS_MIN_MINOR
- FreeBSD: Simplify zfsdev state destruction
- Assert zs_minor is valid in zfsdev_close
- Make locking around zfsdev state match Linux
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11720
This will allow platforms to implement it as they see fit, in particular
in a different manner than rrm locks.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
They are not very useful and hard to implement in the rms routine
the code is about to start using.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
1. even up ifdefs
2. drop the arguably useless teardown lock asserts -- nothing else
checks for it
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11153
A few deadman tunables ended up in the wrong sysctl node.
Move them to vfs.zfs.deadman.*
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11715
zil_replaying(zil, tx) has the side-effect of informing the ZIL that an
entry has been replayed in the (still open) tx. The ZIL uses that
information to record the replay progress in the ZIL header when that
tx's txg syncs.
ZPL log entries are not idempotent and logically dependent and thus
calling zil_replaying() is necessary for correctness.
For ZVOLs the question of correctness is more nuanced: ZVOL logs only
TX_WRITE and TX_TRUNCATE, both of which are idempotent. Logical
dependencies between two records exist only if the write or discard
request had sync semantics or if the ranges affected by the records
overlap.
Thus, at a first glance, it would be correct to restart replay from
the beginning if we crash before replay completes. But this does not
address the following scenario:
Assume one log record per LWB.
The chain on disk is
HDR -> 1:W(1, "A") -> 2:W(1, "B") -> 3:W(2, "X") -> 4:W(3, "Z")
where N:W(O, C) represents log entry number N which is a TX_WRITE of C
to offset A.
We replay 1, 2 and 3 in one txg, sync that txg, then crash.
Bit flips corrupt 2, 3, and 4.
We come up again and restart replay from the beginning because
we did not call zil_replaying() during replay.
We replay 1 again, then interpret 2's invalid checksum as the end
of the ZIL chain and call replay done.
The replayed zvol content is "AX".
If we had called zil_replaying() the HDR would have pointed to 3
and our resumed replay would not have replayed anything because
3 was corrupted, resulting in zvol content "BX".
If 3 logically depends on 2 then the replay corrupted the ZVOL_OBJ's
contents.
This patch adds the zil_replaying() calls to the replay functions.
Since the callbacks in the replay function need the zilog_t* pointer
so that they can call zil_replaying() we open the ZIL while
replaying in zvol_create_minor(). We also verify that replay has
been done when on-demand-opening the ZIL on the first modifying
bio.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11667
ZFS_READONLY represents the "DOS R/O" attribute.
When that flag is set, we should behave as if write access
were not granted by anything in the ACL. In particular:
We _must_ allow writes after opening the file r/w, then
setting the DOS R/O attribute, and writing some more.
(Similar to how you can write after fchmod(fd, 0444).)
Restore these semantics which were lost on FreeBSD when refactoring
zfs_write. To my knowledge Linux does not actually expose this flag,
but we'll need it to eventually so I've added the supporting checks.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11693
When populating a ZIL destination buffer ensure it is always
zeroed before its contents are constructed.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11687
Even when supplied with an abd to abd_get_offset_struct(), the call
to abd_get_offset_impl() can allocate a different abd. Ensure to
call abd_fini_struct() on the abd that is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jorgen Lundman <lundman@lundman.net>
Closes#11683
Wire up the --enable-debug flag for configure to the FreeBSD module
build. Add --enable-invariants.
The running FreeBSD kernel config is used to detect whether to enable
INVARIANTS if not explicitly specified with --enable-invariants or
--disable-invariants.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11678
The spl_kmem_alloc showed up in some flamegraphs in a single-threaded
4k sync write workload at 85k IOPS on an
Intel(R) Xeon(R) Silver 4215 CPU @ 2.50GHz.
Certainly not a huge win but I believe the change is clean and
easy to maintain down the road.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11666
This value does work as expected, and is documented in the manpage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Jake Howard <git@theorangeone.net>
Closes#11670
When a device which is actively trimming or initializing becomes
FAULTED, and therefore no longer writable, cancel the active
TRIM or initialization. When the device is merely taken offline
with `zpool offline` then stop the operation but do not cancel it.
When the device is brought back online the operation will be
resumed if possible.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Vipin Kumar Verma <vipin.verma@hpe.com>
Signed-off-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Closes#11588
The function has three similar pieces of code: for read-behind pages,
requested pages and read-ahead pages. All three pieces had an
assert to ensure that the page is not mapped. Later the assert was
relaxed to require that the page is not mapped for writing. But that
was done in two places out of three. This change fixes the third piece,
read-ahead.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andriy Gapon <avg@FreeBSD.org>
Closes#11654
After 35ec517 it has become possible to import ZFS pools witn an
active org.illumos:edonr feature on FreeBSD, leading to a panic.
In addition, "zpool status" reported all pools without edonr
as upgradable and "zpool upgrade -v" reported edonr in the list
of upgradable features.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Martin Matuska <mm@FreeBSD.org>
Closes#11653
The struct bio member bi_disk was moved underneath a new member named
bi_bdev. So all attempts to reference bio->bi_disk need to now become
bio->bi_bdev->bd_disk.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11639
The metaslab_disable() call may block waiting for a txg sync.
Therefore it's important that vdev_rebuild_thread release the
SCL_CONFIG read lock it is holding before this call. Failure
to do so can result in the txg_sync thread getting blocked
waiting for this lock which results in a deadlock.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewd-by: Srikanth N S <srikanth.nagasubbaraoseetharaman@hpe.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11647
Calling vdev_free() only requires the we acquire the spa config
SCL_STATE_ALL locks, not the SCL_ALL locks. In particular, we need
need to avoid taking the SCL_CONFIG lock (included in SCL_ALL) as a
writer since this can lead to a deadlock. The txg_sync_thread() may
block in spa_txg_history_init_io() when taking the SCL_CONFIG lock
as a reading when it detects there's a pending writer.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11585
On Linux increase the maximum allowed size of the src nvlist which
can be passed to the /dev/zfs ioctl. Originally, this was set
to a maximum of KMALLOC_MAX_SIZE (4M) because it was kmalloc'd.
Since that time it's been converted to a vmalloc so that's no
longer a hard limit, and it's desirable for `zfs send/recv` to
allow larger nvlists so more snapshots can be sent at once.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#6572Closes#11638
This change modifies the behavior of how we determine how much slop
space to use in the pool, such that now it has an upper limit. The
default upper limit is 128G, but is configurable via a tunable.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Prakash Surya <prakash.surya@delphix.com>
Closes#11023
This prevents a panic after a SLOG add/removal on the root pool followed
by a zpool scrub.
When a SLOG is removed, a hole takes its place - the vdev_ops for a hole
is vdev_hole_ops, which defines the handler functions of vdev_op_hold
and vdev_op_rele as NULL.
This bug has been reported in illumos and FreeBSD, a different trigger
in the FreeBSD report though.
Credit for this patch goes to Patrick Mooney <pmooney@pfmooney.com>
Obtained from: illumos-gate commit: c65bd18728f34725
External-issue: https://www.illumos.org/issues/12981
External-issue: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=252396
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Rob Wing <rob.fx907@gmail.com>
Closes#11623
Making uio_impl.h the common header interface between Linux and FreeBSD
so both OS's can share a common header file. This also helps reduce code
duplication for zfs_uio_t for each OS.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11622
Fix regression seen in issue #11545 where checksum errors
where not being counted or showing up in a zpool event.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#11609
First, the crypto request completion handler contains a bug in that it
fails to reset fs_done correctly after the request is completed. This
is only a problem for asynchronous drivers. Second, some hardware
drivers have input constraints which ZFS does not satisfy. For
instance, ccp(4) apparently requires the AAD length for AES-GCM to be a
multiple of the cipher block size, and with qat(4) the AES-GCM AAD
length may not be longer than 240 bytes. FreeBSD's generic crypto
framework doesn't have a mechanism to automatically fall back to a
software implementation if a hardware driver cannot process a request,
and ZFS does not tolerate such errors.
The plan is to implement such a fallback mechanism, but with FreeBSD
13.0 approaching we should simply disable the use hardware drivers for
now.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#11612
Remove function that become unused after refactoring in
e2af2acce3.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Libby <rlibby@FreeBSD.org>
Closes#11614
Property to allow sets of features to be specified; for compatibility
with specific versions / releases / external systems. Influences
the behavior of 'zpool upgrade' and 'zpool create'. Initial man
page changes and test cases included.
Brief synopsis:
zpool create -o compatibility=off|legacy|file[,file...] pool vdev...
compatibility = off : disable compatibility mode (enable all features)
compatibility = legacy : request that no features be enabled
compatibility = file[,file...] : read features from specified files.
Only features present in *all* files will be enabled on the
resulting pool. Filenames may be absolute, or relative to
/etc/zfs/compatibility.d or /usr/share/zfs/compatibility.d (/etc
checked first).
Only affects zpool create, zpool upgrade and zpool status.
ABI changes in libzfs:
* New function "zpool_load_compat" to load and parse compat sets.
* Add "zpool_compat_status_t" typedef for compatibility parse status.
* Add ZPOOL_PROP_COMPATIBILITY to the pool properties enum
* Add ZPOOL_STATUS_COMPATIBILITY_ERR to the pool status enum
An initial set of base compatibility sets are included in
cmd/zpool/compatibility.d, and the Makefile for cmd/zpool is
modified to install these in $pkgdatadir/compatibility.d and to
create symbolic links to a reasonable set of aliases.
Reviewed-by: ericloewe
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11468
Rather than conditionally compiling out the edonr code for FreeBSD
update zfs_mod_supported_feature() to indicate this feature is
unsupported. This ensures that all spa features are defined on
every platform, even if they are not supported.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11605
Issue #11468
zfs_znode_update_vfs is a more platform-agnostic name than
zfs_inode_update. Besides that, the function's prototype is moved to
include/sys/zfs_znode.h as the function is also used in common code.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ka Ho Ng <khng300@gmail.com>
Sponsored by: The FreeBSD Foundation
Closes#11580
The first time through the loop prevdb and prevhdl are NULL. They
are then both set, but only prevdb is checked. Add an ASSERT to
make it clear that prevhdl must be set when prevdb is.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Kleber <klebertarcisio@yahoo.com.br>
Closes#10754Closes#11575
3d40b65 refactored zfs_vnops.c, which shared much code verbatim between
Linux and BSD. After a successful write, the suid/sgid bits are reset,
and the mode to be written is stored in newmode. On Linux, this was
propagated to both the in-memory inode and znode, which is then updated
with sa_update.
3d40b65 accidentally removed the initialization of newmode, which
happened to occur on the same line as the inode update (which has been
moved out of the function).
The uninitialized newmode can be saved to disk, leading to a crash on
stat() of that file, in addition to a merely incorrect file mode.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Antonio Russo <aerusso@aerusso.net>
Closes#11474Closes#11576
Expand the comments to make it clear exactly what is guaranteed
by dmu_tx_assign() and txg_hold_open(). Additionally, update
the comment which refers to txg_exit() when it should reference
txg_rele_to_sync().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11521
ABD's currently track their parent/child relationship. This applies to
`abd_get_offset()` and `abd_borrow_buf()`. However, nothing depends on
knowing this relationship, it's only used for consistency checks to
verify that we are not destroying an ABD that's still in use. When we
are creating/destroying ABD's frequently, the performance impact of
maintaining these data structures (in particular the atomic
increment/decrement operations) can be measurable.
This commit removes this verification code on production builds, but
keeps it when ZFS_DEBUG is set.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11535
I originally applied a fix in #11539 to fix a parent's child references
when a gang ABD is free'd. However, I did not take into account
abd_gang_add_gang(). We still need to make sure to update the child
references in this function as well. In order to resolve this I removed
decreasing the gang ABD's size in abd_free_gang() as well as moved back
the original placeent of zfs_refcount_remove_many() in abd_free().
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11542
`__vdev_disk_physio()` uses `abd_nr_pages_off()` to allocate a bio with
a sufficient number of iovec's to process this zio (i.e.
`nr_iovecs`/`bi_max_vecs`). If there are not enough iovec's in the bio,
then additional bio's will be allocated. However, this is a sub-optimal
code path. In particular, it requires several abd calls (to
`abd_nr_pages_off()` and `abd_bio_map_off()`) which will have to walk
the constituents of the ABD (the pages or the gang children) because
they are looking for offsets > 0.
For gang ABD's, `abd_nr_pages_off()` returns the number of iovec's
needed for the first constituent, rather than the sum of all
constituents (within the requested range). This always under-estimates
the required number of iovec's, which causes us to always need several
bio's. The end result is that `__vdev_disk_physio()` is usually O(n^2)
for gang ABD's (and occasionally O(n^3), when more than 16 bio's are
needed).
This commit fixes `abd_nr_pages_off()`'s handling of gang ABD's, to
correctly determine how many iovec's are needed, by adding up the number
of iovec's for each of the gang children in the requested range.
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11536
If we do not write any buffers to the cache device and the evict hand
has not advanced do not update the cache device header.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11522Closes#11537
Moving the call to zfs_refcount_remove_many() in abd_free() to be called
before any of the ABD free variants are called. This is necessary
because abd_free_gang() adjusts the abd_size for the gang ABD. If the
parent's child references are removed after free'ing the gang ABD the
refcount is not adjusted correctly for the parent's children.
I also removed some stray abd_put() in comments and changed
abd_free_gang_abd() -> abd_free_gang().
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11539
Before a hash table was added on top of the nvlist code, there were
cases where the nvlist allocation was changed from fnvlist_alloc()
to nvlist_alloc() to avoid expensive NV_UNIQUE_NAME checks. Now
this is no longer necessary. These changes should be reverted to be
consistent with other code. There are some cases where this change
will also reduce the number of iterations.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mark Maybee <mark.maybee@delphix.com>
Closes#11464
There is a race condition in zfs_zrele_async when we are checking if
we would be the one to evict an inode. This can lead to a txg sync
deadlock.
Instead of calling into iput directly, we attempt to perform the atomic
decrement ourselves, unless that would set the i_count value to zero.
In that case, we dispatch a call to iput to run later, to prevent a
deadlock from occurring.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11527Closes#11530
The runtime of vdev_validate is dominated by the disk accesses in
vdev_label_read_config. Speed it up by validating all vdevs in
parallel using a taskq.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
This is similar to what we already do in vdev_geom_read_config.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
metaslab_init is the slowest part of importing a mature pool, and it
must be repeated hundreds of times for each top-level vdev. But its
speed is dominated by a few serialized disk accesses. That can lead to
import times of > 1 hour for pools with many top-level vdevs on spinny
disks.
Speed up the import by using a taskqueue to parallelize vdev_load across
all top-level vdevs.
This also requires adding mutex protection to
metaslab_class_t.mc_historgram. The mc_histogram fields were
unprotected when that code was first written in "Illumos 4976-4984 -
metaslab improvements" (OpenZFS
f3a7f6610f). The lock wasn't added until
3dfb57a35e, though it's unclear exactly
which fields it's supposed to protect. In any case, it wasn't until
vdev_load was parallelized that any code attempted concurrent access to
those fields.
Sponsored by: Axcient
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alan Somers <asomers@gmail.com>
Closes#11470
In order for cppcheck to perform a proper analysis it needs to be
aware of how the sources are compiled (source files, include
paths/files, extra defines, etc). All the needed information is
available from the Makefiles and can be leveraged with a generic
cppcheck Makefile target. So let's add one.
Additional minor changes:
* Removing the cppcheck-suppressions.txt file. With cppcheck 2.3
and these changes it appears to no longer be needed. Some inline
suppressions were also removed since they appear not to be
needed. We can add them back if it turns out they're needed
for older versions of cppcheck.
* Added the ax_count_cpus m4 macro to detect at configure time how
many processors are available in order to run multiple cppcheck
jobs. This value is also now used as a replacement for nproc
when executing the kernel interface checks.
* "PHONY =" line moved in to the Rules.am file which is included
at the top of all Makefile.am's. This is just convenient becase
it allows us to use the += syntax to add phony targets.
* One upside of this integration worth mentioning is it now allows
`make cppcheck` to be run in any directory to check that subtree.
* For the moment, cppcheck is not run against the FreeBSD specific
kernel sources. The cppcheck-FreeBSD target will need to be
implemented and testing on FreeBSD to support this.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
Identical condition and return expression 'rc', return value is
always 0.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
The ASSERT that the passed pointer isn't NULL appears after the
pointer has already been dereferenced. Remove the redundant check.
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11508
When scrubbing, (non-sequential) resilvering, or correcting a checksum
error using RAIDZ parity, ZFS should heal any incorrect RAIDZ parity by
overwriting it. For example, if P disks are silently corrupted (P being
the number of failures tolerated; e.g. RAIDZ2 has P=2), `zpool scrub`
should detect and heal all the bad state on these disks, including
parity. This way if there is a subsequent failure we are fully
protected.
With RAIDZ2 or RAIDZ3, a block can have silent damage to a parity
sector, and also damage (silent or known) to a data sector. In this
case the parity should be healed but it is not.
The problem can be noticed by scrubbing the pool twice. Assuming there
was no damage concurrent with the scrubs, the first scrub should fix all
silent damage, and the second scrub should be "clean" (`zpool status`
should not report checksum errors on any disks). If the bug is
encountered, then the second scrub will repair the silently-damaged
parity that the first scrub failed to repair, and these checksum errors
will be reported after the second scrub. Since the first scrub repaired
all the damaged data, the bug can not be encountered during the second
scrub, so subsequent scrubs (more than two) are not necessary.
The root cause of the problem is some code that was inadvertently added
to `raidz_parity_verify()` by the DRAID changes. The incorrect code
causes the parity healing to be aborted if there is damaged data
(`rc_error != 0`) or the data disk is not present (`!rc_tried`). These
checks are not necessary, because we only call `raidz_parity_verify()`
if we have the correct data (which may have been reconstructed using
parity, and which was verified by the checksum).
This commit fixes the problem by removing the incorrect checks in
`raidz_parity_verify()`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11489Closes#11510
Create a common exit point for spa_export_common (a very long
function), which avoids missing steps on failure. This work
is helpful for the planned forced pool export changes.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Will Andrews <will@firepipe.net>
Closes#11514
Like any other thread created by thread_create() we need to call
thread_exit() to properly clean it up. In particular, this ensures the
tsd hash for the thread is cleared.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11512
Fix two minor errors reported by cppcheck:
In module/zfs/abd.c (abd_get_offset_impl), add non-NULL
assertion to prevent NULL dereference warning.
In module/zfs/arc.c (l2arc_write_buffers), change 'try'
variable to 'pass' to avoid C++ reserved word.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Colm Buckley <colm@tuatha.org>
Closes#11507
Follow up for commit 624222a, value asserted <= SPA_OLD_MAXBLOCKSIZE
instead of SPA_MAXBLOCKSIZE as it should be after the previous change.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11501
Set VIRF_MOUNTPOINT flag on snapshot mountpoint.
Authored-by: Mateusz Guzik <mjg@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11458
Mixing ZIL and normal allocations has several problems:
1. The ZIL allocations are allocated, written to disk, and then a few
seconds later freed. This leaves behind holes (free segments) where the
ZIL blocks used to be, which increases fragmentation, which negatively
impacts performance.
2. When under moderate load, ZIL allocations are of 128KB. If the pool
is fairly fragmented, there may not be many free chunks of that size.
This causes ZFS to load more metaslabs to locate free segments of 128KB
or more. The loading happens synchronously (from zil_commit()), and can
take around a second even if the metaslab's spacemap is cached in the
ARC. All concurrent synchronous operations on this filesystem must wait
while the metaslab is loading. This can cause a significant performance
impact.
3. If the pool is very fragmented, there may be zero free chunks of
128KB or more. In this case, the ZIL falls back to txg_wait_synced(),
which has an enormous performance impact.
These problems can be eliminated by using a dedicated log device
("slog"), even one with the same performance characteristics as the
normal devices.
This change sets aside one metaslab from each top-level vdev that is
preferentially used for ZIL allocations (vdev_log_mg,
spa_embedded_log_class). From an allocation perspective, this is
similar to having a dedicated log device, and it eliminates the
above-mentioned performance problems.
Log (ZIL) blocks can be allocated from the following locations. Each
one is tried in order until the allocation succeeds:
1. dedicated log vdevs, aka "slog" (spa_log_class)
2. embedded slog metaslabs (spa_embedded_log_class)
3. other metaslabs in normal vdevs (spa_normal_class)
The space required for the embedded slog metaslabs is usually between
0.5% and 1.0% of the pool, and comes out of the existing 3.2% of "slop"
space that is not available for user data.
On an all-ssd system with 4TB storage, 87% fragmentation, 60% capacity,
and recordsize=8k, testing shows a ~50% performance increase on random
8k sync writes. On even more fragmented systems (which hit problem #3
above and call txg_wait_synced()), the performance improvement can be
arbitrarily large (>100x).
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Mark Maybee <mark.maybee@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11389
As part of commit 1c2358c1 the custom uio_prefaultpages() code
was removed in favor of using the generic kernel provided
iov_iter_fault_in_readable() interface. Unfortunately, it
turns out that up until the Linux 4.7 kernel the function would
only ever fault in the first iovec of the iov_iter. The result
being uiomove_iov() may hang waiting for the page.
This commit effectively restores the custom uio_prefaultpages()
pages code for Linux 4.9 and earlier kernels which contain the
troublesome version of iov_iter_fault_in_readable().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11463Closes#11484
In FreeBSD the struct uio was just a typedef to uio_t. In order to
extend this struct, outside of the definition for the struct uio, the
struct uio has been embedded inside of a uio_t struct.
Also renamed all the uio_* interfaces to be zfs_uio_* to make it clear
this is a ZFS interface.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Jorgen Lundman <lundman@lundman.net>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Brian Atkinson <batkinson@lanl.gov>
Closes#11438
The `abd_get_offset_*()` routines create an abd_t that references
another abd_t, and doesn't allocate any pages/buffers of its own. In
some workloads, these routines may be called frequently, to create many
abd_t's representing small pieces of a single large abd_t. In
particular, the upcoming RAIDZ Expansion project makes heavy use of
these routines.
This commit adds the ability for the caller to allocate and provide the
abd_t struct to a variant of `abd_get_offset_*()`. This eliminates the
cost of allocating the abd_t and performing the accounting associated
with it (`abdstat_struct_size`). The RAIDZ/DRAID code uses this for
the `rc_abd`, which references the zio's abd. The upcoming RAIDZ
Expansion project will leverage this infrastructure to increase
performance of reads post-expansion by around 50%.
Additionally, some of the interfaces around creating and destroying
abd_t's are cleaned up. Most significantly, the distinction between
`abd_put()` and `abd_free()` is eliminated; all types of abd_t's are
now disposed of with `abd_free()`.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Issue #8853Closes#11439
Each zfs ioctl that changes on-disk state (e.g. set property, create
snapshot, destroy filesystem) is recorded in the zpool history, and is
printed by `zpool history -i`.
For performance diagnostic purposes, it would be useful to know how long
each of these ioctls took to run. This commit adds that functionality,
with a new `ZPOOL_HIST_ELAPSED_NS` member of the history nvlist.
Additionally, the time recorded in this history log is currently the
time that the history record is written to disk. But in many cases (CLI
args logging and ioctl logging), this happens asynchronously,
potentially many seconds after the operation completed. This commit
changes the timestamp to reflect when the history event was created,
rather than when it was written to disk.
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11440
If the system is very low on memory (specifically,
`arc_free_memory() < arc_sys_free/2`, i.e. less than 1/16th of RAM
free), `arc_evict_state_impl()` will defer wakups. In this case, the
arc_evict_waiter_t's remain on the list, even though `arc_evict_count`
has been incremented past their `aew_count`.
The problem is that `arc_wait_for_eviction()` assumes that if there are
waiters on the list, the count they are waiting for has not yet been
reached. However, the deferred wakeups may violate this, causing
`ASSERT(last->aew_count > arc_evict_count)` to fail.
This commit resolves the issue by having new waiters use the greater of
`arc_evict_count` and the last `aew_count`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11285Closes#11397
Virtuozzo 7 kernels starting 3.10.0-1127.18.2.vz7.163.46
have the following configuration:
* no HAVE_VFS_RW_ITERATE
* HAVE_VFS_DIRECT_IO_ITER_RW_OFFSET
=> let's add implementation of zpl_direct_IO() via
zpl_aio_{read,write}() in this case.
https://bugs.openvz.org/browse/OVZ-7243
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Closes#11410Closes#11411
Build error on illumos with gcc 10 did reveal:
In function 'dmu_objset_refresh_ownership':
../../common/fs/zfs/dmu_objset.c:857:25: error: implicit conversion
from 'boolean_t' to 'ds_hold_flags_t' {aka 'enum ds_hold_flags'}
[-Werror=enum-conversion]
857 | dsl_dataset_disown(ds, decrypt, tag);
| ^~~~~~~
cc1: all warnings being treated as errors
libzfs_input_check.c: In function 'zfs_ioc_input_tests':
libzfs_input_check.c:754:28: error: implicit conversion from
'enum dmu_objset_type' to 'enum lzc_dataset_type'
[-Werror=enum-conversion]
754 | err = lzc_create(dataset, DMU_OST_ZFS, NULL, NULL, 0);
| ^~~~~~~~~~~
cc1: all warnings being treated as errors
The same issue is present in openzfs, and also the same issue about
ds_hold_flags_t, which currently defines exactly one valid value.
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#11406
As of 5.11 the blk_register_region() and blk_unregister_region()
functions have been retired. This isn't a problem since add_disk()
has implicitly allocated minor numbers for a very long time.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Both revalidate_disk_size() and revalidate_disk() have been removed.
Functionally this isn't a problem because we only relied on these
functions to call zvol_revalidate_disk() for us and to perform any
additional handling which might be needed for that kernel version.
When neither are available we know there's no additional handling
needed and we can directly call zvol_revalidate_disk().
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The bd_contains member was removed from the block_device structure.
Callers needing to determine if a vdev is a whole block device should
use the new bdev_whole() wrapper. For older kernels we provide our
own bdev_whole() wrapper which relies on bd_contains for compatibility.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The generic IO accounting functions have been removed in favor of the
bio_start_io_acct() and bio_end_io_acct() functions which provide a
better interface. These new functions were introduced in the 5.8
kernels but it wasn't until the 5.11 kernel that the previous generic
IO accounting interfaces were removed.
This commit updates the blk_generic_*_io_acct() wrappers to provide
and interface similar to the updated kernel interface. It's slightly
different because for older kernels we need to pass the request queue
as well as the bio.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
The lookup_bdev() function has been updated to require a dev_t
be passed as the second argument. This is actually pretty nice
since the major number stored in the dev_t was the only part we
were interested in. This allows to us avoid handling the bdev
entirely. The vdev_lookup_bdev() wrapper was updated to emulate
the behavior of the new lookup_bdev() for all supported kernels.
Reviewed-by: Rafael Kitover <rkitover@gmail.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11387Closes#11390
Individual transactions may not be larger than DMU_MAX_ACCESS.
This is enforced by the assertions in dmu_tx_hold_write() and
dmu_tx_hold_write_by_dnode(). There's an additional check in
dmu_tx_count_write() however it has no effect and only sets a
local err variable. We could enable this check, however since
it's already enforced by ASSERTs elsewhere I opted to remove it
instead.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#3731Closes#11384
After porting the fix for https://github.com/openzfs/zfs/issues/5295
over to illumos, we started hitting an assertion failure when running
the testsuite:
assertion failed: rc->rc_count == number, file: .../refcount.c
and the unexpected hold has this stack:
dsl_dataset_long_hold+0x59 dmu_objset_upgrade+0x73
dmu_objset_id_quota_upgrade+0x15 dmu_objset_own+0x14f
The simplest reproducer for this in illumos is
zpool create -f -O version=1 testpool c3t0d0; zpool destroy testpool
which is run as part of the zpool_create_tempname test, but I can't get
this to trigger on FreeBSD. This appears to be because of the call to
txg_wait_synced() in dmu_objset_upgrade_stop() (which was missing in
illumos), slows down dmu_objset_disown() enough to avoid the condition.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andy Fiddaman <andy@omnios.org>
Closes#11368
Commit 1c2358c12 restructured this code and introduced a warning
about the variable maybe not being initialized. This cannot happen
with the updated code but we should initialize the variable anyway
to silence the warning.
zpl_file.c: In function ‘zpl_iter_write’:
zpl_file.c:324:9: warning: ‘count’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11373
There's no need to call iov_iter_advance() in zpl_iter_read().
This was preserved from the previous code where it wasn't needed
but also didn't cause any problems. Now that the iter functions
also handle pipes that's no longer the case. When fully reading a
pipe buffer iov_iter_advance() may results in the pipe buf release
function being called which will not be registered resulting in
a NULL dereference.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11375Closes#11378
Based on a conversation with Matt on the OpenZFS Slack.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11370
Commit 59b68723 added a configure check for 5.10, which removed
revalidate_disk(), and conditionally replaced it's usage with a call to
the new revalidate_disk_size() function. However, the old function also
invoked the device's registered callback, in our case
zvol_revalidate_disk(). This commit adds a call to zvol_revalidate_disk()
in zvol_update_volsize() to make sure the code path stays the same.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Closes#11358
As of the 5.10 kernel the generic splice compatibility code has been
removed. All filesystems are now responsible for registering a
->splice_read and ->splice_write callback to support this operation.
The good news is the VFS provided generic_file_splice_read() and
iter_file_splice_write() callbacks can be used provided the ->iter_read
and ->iter_write callback support pipes. However, this is currently
not the case and only iovecs and bvecs (not pipes) are ever attached
to the uio structure.
This commit changes that by allowing full iov_iter structures to be
attached to uios. Ever since the 4.9 kernel the iov_iter structure
has supported iovecs, kvecs, bvevs, and pipes so it's desirable to
pass the entire thing when possible. In conjunction with this the
uio helper functions (i.e uiomove(), uiocopy(), etc) have been
updated to understand the new UIO_ITER type.
Note that using the kernel provided uio_iter interfaces allowed the
existing Linux specific uio handling code to be simplified. When
there's no longer a need to support kernel's older than 4.9, then
it will be possible to remove the iovec and bvec members from the
uio structure and always use a uio_iter. Until then we need to
maintain all of the existing types for older kernels.
Some additional refactoring and cleanup was included in this change:
- Added checks to configure to detect available iov_iter interfaces.
Some are available all the way back to the 3.10 kernel and are used
when available. In particular, uio_prefaultpages() now always uses
iov_iter_fault_in_readable() which is available for all supported
kernels.
- The unused UIO_USERISPACE type has been removed. It is no longer
needed now that the uio_seg enum is platform specific.
- Moved zfs_uio.c from the zcommon.ko module to the Linux specific
platform code for the zfs.ko module. This gets it out of libzfs
where it was never needed and keeps this Linux specific code out
of the common sources.
- Removed unnecessary O_APPEND handling from zfs_iter_write(), this
is redundant and O_APPEND is already handled in zfs_write();
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11351
The space in special devices is not included in spa_dspace (or
dsl_pool_adjustedsize(), or the zfs `available` property). Therefore
there is always at least as much free space in the normal class, as
there is allocated in the special class(es). And therefore, there is
always enough free space to remove a special device.
However, the checks for free space when removing special devices did not
take this into account. This commit corrects that.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11329
After e357046 it should not be necessary to periodically update ARC
kstats and tunables. Tunable updates are applied when modified, and
kstats are updated on demand.
Update kstats in `arc_evict_cb_check()` for `ZFS_DEBUG` builds only.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11237
On a system with very high fragmentation, we may need to do lots of gang
allocations (e.g. most indirect block allocations (~50KB) may need to
gang). Before failing a "normal" allocation and resorting to ganging, we
try every metaslab. This has the impact of loading every metaslab (not
a huge deal since we now typically keep all metaslabs loaded), and also
iterating over every metaslab for every failing allocation. If there are
many metaslabs (more than the typical ~200, e.g. due to vdev expansion
or very large vdevs), the CPU cost of this iteration can be very
impactful. This iteration is done with the mg_lock held, creating long
hold times and high lock contention for concurrent allocations,
ultimately causing long txg sync times and poor application performance.
To address this, this commit changes the behavior of "normal" (not
try_hard, not ZIL) allocations. These will now only examine the 100
best metaslabs (as determined by their ms_weight). If none of these
have a large enough free segment, then the allocation will fail and
we'll fall back on ganging.
To accomplish this, we will now (normally) gang before doing a
`try_hard` allocation. Non-try_hard allocations will only examine the
100 best metaslabs of each vdev. In summary, we will first try normal
allocation. If that fails then we will do a gang allocation. If that
fails then we will do a "try hard" gang allocation. If that fails then
we will have a multi-layer gang block.
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11327
Metaslab rotor and aliquot are used to distribute workload between
vdevs while keeping some locality for logically adjacent blocks. Once
multiple allocators were introduced to separate allocation of different
objects it does not make much sense for different allocators to write
into different metaslabs of the same metaslab group (vdev) same time,
competing for its resources. This change makes each allocator choose
metaslab group independently, colliding with others only sporadically.
Test including simultaneous write into 4 files with recordsize of 4KB
on a striped pool of 30 disks on a system with 40 logical cores show
reduction of vdev queue lock contention from 54 to 27% due to better
load distribution. Unfortunately it won't help much ZVOLs yet since
only one dataset/ZVOL is synced at a time, and so for the most part
only one allocator is used, but it may improve later.
While there, to reduce the number of pointer dereferences change
per-allocator storage for metaslab classes and groups from several
separate malloc()'s to variable length arrays at the ends of the
original class and group structures.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11288
Avoid a bug with gcc's -Wreturn-local-addr warning with some
obfuscation. In buggy versions of gcc, if a return value is an
expression that involves the address of a local variable, and even if
that address is legally converted to a non-pointer type, a warning may
be emitted and the value of the address may be replaced with zero.
Howerver, buggy versions don't emit the warning or replace the value
when simply returning a local variable of non-pointer type.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=90737
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Libby <rlibby@FreeBSD.org>
Closes#11337
The last change caused the read completion callback to not be called
if the IO was still in progress. This change restores allocation
of the arc buf callback, but in the callback path checks the new
acb_nobuf field to know to skip buffer allocation.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11324
When removing and subsequently reattaching a vdev, CKSUM errors may
occur as vdev_indirect_read_all() reads from all children of a mirror
in case of a resilver.
Fix this by checking whether a child is missing the data and setting a
flag (ic_error) which is then checked in vdev_indirect_repair() and
suppresses incrementing the checksum counter.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11277
There is a tunable to select the fletcher 4 checksum implementation on
Linux but it was not present in FreeBSD.
Implement the sysctl handler for FreeBSD and use ZFS_MODULE_PARAM_CALL
to provide the tunable on both platforms.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11270
The performance of `zfs receive` can be bottlenecked on the CPU consumed
by the `receive_writer` thread, especially when receiving streams with
small compressed block sizes. Much of the CPU is spent creating and
destroying dbuf's and arc buf's, one for each `WRITE` record in the send
stream.
This commit introduces the concept of "lightweight writes", which allows
`zfs receive` to write to the DMU by providing an ABD, and instantiating
only a new type of `dbuf_dirty_record_t`. The dbuf and arc buf for this
"dirty leaf block" are not instantiated.
Because there is no dbuf with the dirty data, this mechanism doesn't
support reading from "lightweight-dirty" blocks (they would see the
on-disk state rather than the dirty data). Since the dedup-receive code
has been removed, `zfs receive` is write-only, so this works fine.
Because there are no arc bufs for the received data, the received data
is no longer cached in the ARC.
Testing a receive of a stream with average compressed block size of 4KB,
this commit improves performance by 50%, while also reducing CPU usage
by 50% of a CPU. On a per-block basis, CPU consumed by receive_writer()
and dbuf_evict() is now 1/7th (14%) of what it was.
Baseline: 450MB/s, CPU in receive_writer() 40% + dbuf_evict() 35%
New: 670MB/s, CPU in receive_writer() 17% + dbuf_evict() 0%
The code is also restructured in a few ways:
Added a `dr_dnode` field to the dbuf_dirty_record_t. This simplifies
some existing code that no longer needs `DB_DNODE_ENTER()` and related
routines. The new field is needed by the lightweight-type dirty record.
To ensure that the `dr_dnode` field remains valid until the dirty record
is freed, we have to ensure that the `dnode_move()` doesn't relocate the
dnode_t. To do this we keep a hold on the dnode until it's zio's have
completed. This is already done by the user-accounting code
(`userquota_updates_task()`), this commit extends that so that it always
keeps the dnode hold until zio completion (see `dnode_rele_task()`).
`dn_dirty_txg` was previously zeroed when the dnode was synced. This
was not necessary, since its meaning can be "when was this dnode last
dirtied". This change simplifies the new `dnode_rele_task()` code.
Removed some dead code related to `DRR_WRITE_BYREF` (dedup receive).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11105
In the redaction list traversal code, there is a bug in the binary search
logic when looking for the resume point. Maxbufid can be decremented to -1,
causing us to read the last possible block of the object instead of the one we
wanted. This can cause incorrect resume behavior, or possibly even a hang in
some cases. In addition, when examining non-last blocks, we can treat the
block as being the same size as the last block, causing us to miss entries in
the redaction list when determining where to resume. Finally, we were ignoring
the case where the resume point was found in the buffer being searched, and
resuming from minbufid. All these issues have been corrected, and the code has
been significantly simplified to make future issues less likely.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11297
vfs.zfs.arc_no_grow_shift has an invalid type (15) and this causes
py-sysctl to format it as a bytearray when it should be an integer.
"U" is not a valid format, it should be "I" and the type should match
the variable type, int. We can return EINVAL if the value is set below
zero.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11318
Resolve an uninitialized variable warning when compiling.
In function ‘zfs_domount’:
warning: ‘root_inode’ may be used uninitialized in this
function [-Wmaybe-uninitialized]
sb->s_root = d_make_root(root_inode);
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11306
ZFS currently doesn't react to hotplugging cpu or memory into the
system in any way. This patch changes that by adding logic to the ARC
that allows the system to take advantage of new memory that is added
for caching purposes. It also adds logic to the taskq infrastructure
to support dynamically expanding the number of threads allocated to a
taskq.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Ahrens <matthew.ahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11212
There has been a panic affecting some system configurations where the
thread FPU context is disturbed during the fletcher 4 benchmarks,
leading to a panic at boot.
module_init() registers zcommon_init to run in the last subsystem
(SI_SUB_LAST). Running it as soon as interrupts have been configured
(SI_SUB_INT_CONFIG_HOOKS) makes sure we have finished the benchmarks
before we start doing other things.
While it's not clear *how* the FPU context was being disturbed, this
does seem to avoid it.
Add a module_init_early() macro to run zcommon_init() at this earlier
point on FreeBSD. On Linux this is defined as module_init().
Authored by: Konstantin Belousov <kib@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11302
Add ARC_FLAG_NO_BUF to indicate that a buffer need not be
instantiated. This fixes a ~20% performance regression on
cached reads due to zfetch changes.
Reviewed-by: Tony Nguyen <tony.nguyen@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11220Closes#11232
The fnvlist_lookup_boolean_value() function should not be used
to check the force argument since it's optional. It may not be
provided or may have been created with the wrong flags.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11281Closes#11284
During module load time all of the available fetcher4 and raidz
implementations are benchmarked for a fixed amount of time to
determine the fastest available. Manual testing has shown that this
time can be significantly reduced with negligible effect on the final
results.
This commit changes the benchmark time to 1ms which can reduce the
module load time by over a second on x86_64. On an x86_64 system
with sse3, ssse3, and avx2 instructions the benchmark times are:
Fletcher4 603ms -> 15ms
RAIDZ 1,322ms -> 64ms
Reviewed-by: Matthew Macy <mmacy@freebsd.org>
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11282
Since 8c4fb36a24 (PR #7795) spa_has_pending_synctask() started to
take two more locks per write inside txg_all_lists_empty(). I am
surprised those pool-wide locks are not contended, but still their
operations are visible in CPU profiles under contended vdev lock.
This commit slightly changes vdev_queue_max_async_writes() flow to
not call the function if we are going to return max_active any way
due to high amount of dirty data. It allows to save some CPU time
exactly when the pool is busy.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11280
With both abd_size and abd_nents being uint_t it makes no sense for
abd_chunkcnt_for_bytes() to return size_t. Random mix of different
types used to count chunks looks bad and makes compiler more difficult
to optimize the code.
In particular on FreeBSD this change allows compiler to completely
optimize out abd_verify_scatter() when built without debug, removing
pointless 64-bit division and even more pointless empty loop.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11279
When sending raw encrypted datasets the user space accounting is present
when it's not expected to be. This leads to the subsequent mount failure
due a checksum error when verifying the local mac.
Fix this by clearing the OBJSET_FLAG_USERACCOUNTING_COMPLETE and reset
the local mac. This allows the user accounting to be correctly updated
on first mount using the normal upgrade process.
Reviewed-By: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-By: Tom Caputi <caputit1@tcnj.edu>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10523Closes#11221
It was found that setting min_active tunables for non-interactive I/Os
makes them stuck. It is caused by zfs_vdev_nia_delay, that can never
be reached if we never issue any I/Os due to min_active set to zero.
Fix this by issuing at least one non-interactive I/O at a time when
there are no interactive I/Os. When there are interactive I/Os, zero
min_active allows to completely block any non-interactive I/O. It may
min_active starvation in some scenarios, but who we are to deny foot
shooting?
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11261
This is needed for zfsd to autoreplace vdevs.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11260
In function dmu_buf_hold_array_by_dnode, the usage of zio is only for
the reading operation. Only create the zio and wait it in the reading
scenario as a performance optimization.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Finix Yan <yancw@info2soft.com>
Closes#11251Closes#11256
Commit 85703f6 added a new ASSERT to zfs_write() as part of the
cleanup which isn't correct in the case where multiple processes
are concurrently extending a file. The `zp->z_size` is updated
atomically while holding a range lock on only a portion of the
file. Therefore, it's possible for the file size to increase
after a same check is performed earlier in the loop causing this
ASSERT to fail. The code itself handles this case correctly so
only the invalid ASSERT needs to be removed.
Reviewed-by: Brian Atkinson <batkinson@lanl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11235
Investigating influence of scrub (especially sequential) on random read
latency I've noticed that on some HDDs single 4KB read may take up to 4
seconds! Deeper investigation shown that many HDDs heavily prioritize
sequential reads even when those are submitted with queue depth of 1.
This patch addresses the latency from two sides:
- by using _min_active queue depths for non-interactive requests while
the interactive request(s) are active and few requests after;
- by throttling it further if no interactive requests has completed
while configured amount of non-interactive did.
While there, I've also modified vdev_queue_class_to_issue() to give
more chances to schedule at least _min_active requests to the lowest
priorities. It should reduce starvation if several non-interactive
processes are running same time with some interactive and I think should
make possible setting of zfs_vdev_max_active to as low as 1.
I've benchmarked this change with 4KB random reads from ZVOL with 16KB
block size on newly written non-fragmented pool. On fragmented pool I
also saw improvements, but not so dramatic. Below are log2 histograms
of the random read latency in milliseconds for different devices:
4 2x mirror vdevs of SATA HDD WDC WD20EFRX-68EUZN0 before:
0, 0, 2, 1, 12, 21, 19, 18, 10, 15, 17, 21
after:
0, 0, 0, 24, 101, 195, 419, 250, 47, 4, 0, 0
, that means maximum latency reduction from 2s to 500ms.
4 2x mirror vdevs of SATA HDD WDC WD80EFZX-68UW8N0 before:
0, 0, 2, 31, 38, 28, 18, 12, 17, 20, 24, 10, 3
after:
0, 0, 55, 247, 455, 470, 412, 181, 36, 0, 0, 0, 0
, i.e. from 4s to 250ms.
1 SAS HDD SEAGATE ST14000NM0048 before:
0, 0, 29, 70, 107, 45, 27, 1, 0, 0, 1, 4, 19
after:
1, 29, 681, 1261, 676, 1633, 67, 1, 0, 0, 0, 0, 0
, i.e. from 4s to 125ms.
1 SAS SSD SEAGATE XS3840TE70014 before (microseconds):
0, 0, 0, 0, 0, 0, 0, 0, 70, 18343, 82548, 618
after:
0, 0, 0, 0, 0, 0, 0, 0, 283, 92351, 34844, 90
I've also measured scrub time during the test and on idle pools. On
idle fragmented pool I've measured scrub getting few percent faster
due to use of QD3 instead of QD2 before. On idle non-fragmented pool
I've measured no difference. On busy non-fragmented pool I've measured
scrub time increase about 1.5-1.7x, while IOPS increase reached 5-9x.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11166
The documentation describes dRAID as a distributed spare, not
parity, RAID implementation. Update the short feature description
to match the rest of the documentation.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11229
Commit a1d477c2 accidentally disabled DTL updates for the zil_claim()
case described at the end of vdev_stat_update() by unconditionally
disabling all DTL updates when loading. This was done to avoid
a deadlock on the vd_dtl_lock when loading the DTLs from disk.
vdev_dtl_contains <--- Takes vd->vd_dtl_lock
vdev_mirror_child_missing
vdev_mirror_io_start
zio_vdev_io_start
__zio_execute
arc_read
dbuf_issue_final_prefetch
dbuf_prefetch_impl
dbuf_prefetch
dmu_prefetch
space_map_iterate
space_map_load_length
space_map_load
vdev_dtl_load <--- Takes vd->vd_dtl_lock
vdev_load
spa_ld_load_vdev_metadata
spa_tryimport
The missing DTL updates can be restored by moving the space_map_load()
call outside the vd_dtl_lock. A private range tree is populated by
reading the space map and then merged in to the DTL_MISSING tree
under the lock.
Furthermore, the SPA_LOAD_NONE check in vdev_dtl_contains() leads to an
additional problem. Any resilvering which occurs before SPA_LOAD_NONE
is set will incorrectly determine that there's nothing to repair. This
can result in full redundancy not being restored for some blocks.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11218
Is this block when abuf != NULL ever reached? Yes, it is.
Add asserts and comments to prove that when we get here, we have a full
block write at an aligned offset extending past EOF.
Simplify by removing the check that tx_bytes == max_blksz, since we can
assert that it is always true.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11191
- Don't leave fstrans set when passed a snapshot
- Don't remove minor if volmode already matches new value
- (FreeBSD) Wait for GEOM ops to complete before trying
remove (at create time GEOM will be "tasting" in parallel)
- (FreeBSD) Don't leak zvol_state_lock on open if zv == NULL
- (FreeBSD) Don't try to unlock zv->zv_state lock if zv == NULL
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11199
For encrypted receives, where user accounting is initially disabled on
creation, both 'zfs userspace' and 'zfs groupspace' fails with
EOPNOTSUPP: this is because dmu_objset_id_quota_upgrade_cb() forgets to
set OBJSET_FLAG_USERACCOUNTING_COMPLETE on the objset flags after a
successful dmu_objset_space_upgrade().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: loli10K <ezomori.nozomu@gmail.com>
Closes#9501Closes#9596
In case of cache device removal it is possible that at the end of
l2arc_evict() we have l2ad_hand = l2ad_evict. This can lead to the
following panic in case of a debug build:
VERIFY3(dev->l2ad_hand < dev->l2ad_evict) failed (321920512 < 321920512)
Call Trace:
dump_stack+0x66/0x90
spl_panic+0xef/0x117 [spl]
l2arc_remove_vdev+0x11d/0x290 [zfs]
spa_load_l2cache+0x275/0x5b0 [zfs]
spa_vdev_remove+0x4a5/0x6e0 [zfs]
zfs_ioc_vdev_remove+0x59/0xa0 [zfs]
zfsdev_ioctl_common+0x5b3/0x630 [zfs]
zfsdev_ioctl+0x53/0xe0 [zfs]
do_vfs_ioctl+0x42e/0x6b0
ksys_ioctl+0x5e/0x90
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In case of cache device removal it also possible that l2ad_hand +
distance > l2ad_end since we do not iterate l2arc_evict() and l2ad_hand
is not reset. This has no functional consequence however as the cache
device is about to be removed.
Fix this by omitting the ASSERT in case of device removal.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#11205
The ZFS_ENTER/ZFS_EXIT/ZFS_VERFY_ZP macros should not be used
in the Linux zpl_*.c source files. They return a positive error
value which is correct for the common code, but not for the Linux
specific kernel code which expects a negative return value. The
ZPL_ENTER/ZPL_EXIT/ZPL_VERFY_ZP macros should be used instead.
Furthermore, the ZPL_EXIT macro has been updated to not call the
zfs_exit_fs() function. This prevents a possible deadlock which
can occur when a snapshot is automatically unmounted because the
zpl_show_devname() must never wait on in progress automatic
snapshot unmounts.
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11169Closes#11201
The output of ZFS channel programs is logged on-disk in the zpool
history, and printed by `zpool history -i`. Channel programs can use
10MB of memory by default, and up to 100MB by using the `zfs program -m`
flag. Therefore their output can be up to some fraction of 100MB.
In addition to being somewhat wasteful of the limited space reserved for
the pool history (which for large pools is 1GB), in extreme cases this
can result in a failure of `ASSERT(length <= DMU_MAX_ACCESS);` in
`dmu_buf_hold_array_by_dnode()`.
This commit limits the output size that will be logged to 1MB. Larger
outputs will not be logged, instead a entry will be logged indicating
the size of the omitted output.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11194
FreeBSD's VFS expects EFAULT from zfs_write() if we didn't complete
the full write so it can retry the operation. Add some missing
SET_ERRORs in zfs_write().
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11193
This patch adds a new top-level vdev type called dRAID, which stands
for Distributed parity RAID. This pool configuration allows all dRAID
vdevs to participate when rebuilding to a distributed hot spare device.
This can substantially reduce the total time required to restore full
parity to pool with a failed device.
A dRAID pool can be created using the new top-level `draid` type.
Like `raidz`, the desired redundancy is specified after the type:
`draid[1,2,3]`. No additional information is required to create the
pool and reasonable default values will be chosen based on the number
of child vdevs in the dRAID vdev.
zpool create <pool> draid[1,2,3] <vdevs...>
Unlike raidz, additional optional dRAID configuration values can be
provided as part of the draid type as colon separated values. This
allows administrators to fully specify a layout for either performance
or capacity reasons. The supported options include:
zpool create <pool> \
draid[<parity>][:<data>d][:<children>c][:<spares>s] \
<vdevs...>
- draid[parity] - Parity level (default 1)
- draid[:<data>d] - Data devices per group (default 8)
- draid[:<children>c] - Expected number of child vdevs
- draid[:<spares>s] - Distributed hot spares (default 0)
Abbreviated example `zpool status` output for a 68 disk dRAID pool
with two distributed spares using special allocation classes.
```
pool: tank
state: ONLINE
config:
NAME STATE READ WRITE CKSUM
slag7 ONLINE 0 0 0
draid2:8d:68c:2s-0 ONLINE 0 0 0
L0 ONLINE 0 0 0
L1 ONLINE 0 0 0
...
U25 ONLINE 0 0 0
U26 ONLINE 0 0 0
spare-53 ONLINE 0 0 0
U27 ONLINE 0 0 0
draid2-0-0 ONLINE 0 0 0
U28 ONLINE 0 0 0
U29 ONLINE 0 0 0
...
U42 ONLINE 0 0 0
U43 ONLINE 0 0 0
special
mirror-1 ONLINE 0 0 0
L5 ONLINE 0 0 0
U5 ONLINE 0 0 0
mirror-2 ONLINE 0 0 0
L6 ONLINE 0 0 0
U6 ONLINE 0 0 0
spares
draid2-0-0 INUSE currently in use
draid2-0-1 AVAIL
```
When adding test coverage for the new dRAID vdev type the following
options were added to the ztest command. These options are leverages
by zloop.sh to test a wide range of dRAID configurations.
-K draid|raidz|random - kind of RAID to test
-D <value> - dRAID data drives per group
-S <value> - dRAID distributed hot spares
-R <value> - RAID parity (raidz or dRAID)
The zpool_create, zpool_import, redundancy, replacement and fault
test groups have all been updated provide test coverage for the
dRAID feature.
Co-authored-by: Isaac Huang <he.huang@intel.com>
Co-authored-by: Mark Maybee <mmaybee@cray.com>
Co-authored-by: Don Brady <don.brady@delphix.com>
Co-authored-by: Matthew Ahrens <mahrens@delphix.com>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Mark Maybee <mmaybee@cray.com>
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10102
ZFS channel programs (invoked by `zfs program`) are executed in a LUA
sandbox with a limit on the amount of memory they can consume. The
limit is 10MB by default, and can be raised to 100MB with the `-m` flag.
If the memory limit is exceeded, the LUA program exits and the command
fails with a message like `Channel program execution failed: Memory
limit exhausted.`
The LUA sandbox allocates memory with `vmem_alloc(KM_NOSLEEP)`, which
will fail if the requested memory is not immediately available. In this
case, the program fails with the same message, `Memory limit exhausted`.
However, in this case the specified memory limit has not been reached,
and the memory may only be temporarily unavailable.
This commit changes the LUA memory allocator `zcp_lua_alloc()` to use
`vmem_alloc(KM_SLEEP)`, so that we won't spuriously fail when memory is
temporarily low. Instead, we rely on the system to be able to free up
memory (e.g. by evicting from the ARC), and we assume that even at the
highest memory limit of 100MB, the channel program will not truly
exhaust the system's memory.
External-issue: DLPX-71924
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#11190
The custom zpl_show_devname() helper should translate spaces in
to the octal escape sequence \040. The getmntent(2) function
is aware of this convention and properly translates the escape
character back to a space when reading the fsname.
Without this change the `zfs mount` and `zfs unmount` commands
incorrectly detect when a dataset with a name containing spaces
is mounted.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11182Closes#11187
It is a leftover from illumos always set to NULL and introducing a
spurious difference between zio_buf and zio_data_buf.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11188
The microzap hash can sometimes be zero for single digit snapnames.
The zap cursor can then have a serialized value of two (for . and ..),
and skip the first entry in the avl tree for the .zfs/snapshot directory
listing, and therefore does not return all snapshots.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: Tony Perkins <tperkins@datto.com>
Closes#11039
The field is yet another leftover from unsupported zfs_znode_move.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11186
We can consolidate the unlocking procedure into one place by starting
with drop_suspend set to B_FALSE and moving the open count check up.
While here, a little code cleanup. Match the out labels between
zvol_geom_open and zvol_cdev_open, and add a missing period in some
comments.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
zvol_first_open can fail with EINTR if spa_namespace_lock is not held
and cannot be taken without waiting.
Apply the same logic that was done for zvol_geom_open to take
spa_namespace_lock if not already held on first open in zvol_cdev_open.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11175
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11176
Show that these values will not be changing later.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11176
The oid comes from the znode we are already passing.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11176
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11176
After initial arc_c was reduced to arc_c_min it became possible that
on datasets with primarycache=metadata or none dirty data make up most
of ARC capacity and easily more than configured 50% of initial arc_c,
that causes forced txg commits by arc_tempreserve_space() and periodic
very long write delays.
This patch makes arc_tempreserve_space() to use arc_c only after ARC
warmed up once and arc_c really means something, but use arc_c_max
before that.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Sponsored-By: iXsystems, Inc.
Closes#11178
Fix a couple of places where the wrong tag is passed
to dnode_{hold, rele}
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11184
Check if the ZVOL has been written before calling zil_async_to_sync.
The ZIL will be opened on the first write, not earlier.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#11152
spa_config_load() passes NULL into resid when doing zfs_file_read().
This would trip over when vfs.zfs.autoimport_disable=0.
Sponsored by: The FreeBSD Foundation
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Ka Ho Ng <khng@freebsdfoundation.org>
Closes#11149
SET_ERROR is useful to trace errors, so use it where the errors occur
rather than factored out to the end of a function.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11146
A new function was added named revalidate_disk_size() and the old
revalidate_disk() appears to have been deprecated. As the only ZFS
code that calls this function is zvol_update_volsize, swapping the
old function call out for the new one should be all that is required.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel 5.10 removed check_disk_change() in favor of callers using
the faster bdev_check_media_change() instead, and explicitly forcing
bdev revalidation when they desire that behavior. To preserve prior
behavior, I have wrapped this into a zfs_check_media_change() macro
that calls an inline function for the new API that mimics the old
behavior when check_disk_change() doesn't exist, and just calls
check_disk_change() if it exists.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Kernel commit 2b0d3d3e4fcfb brought in some changes to the struct
percpu_ref structure that moves most of its fields into a member
struct named "data" of type struct percpu_ref_data. This includes
the "count" member which is updated by vdev_blkg_tryget(), so update
this function to chase the API change, and detect it via configure.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Coleman Kane <ckane@colemankane.org>
Closes#11085
Avoid checking the whole array of objects each time by removing the self
organized memory reaping. this can be managed by the global memory reap
callback which is called every 60 seconds. this will reduce the use if
locking operations significant.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#11126
Move zfs_get_data() in to platform-independent code. The only
platform-specific aspect of it is the way we release an inode
(Linux) / vnode_t (FreeBSD). I am not aware of a platform that
could be supported by ZFS that couldn't implement zfs_rele_async
itself. It's sibling zvol_get_data already is platform-independent.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#10979
Current CPU_SEQID users don't care about possibly changing CPU ID, but
enclose it within kpreempt disable/enable in order to fend off warnings
from Linux's CONFIG_DEBUG_PREEMPT.
There is no need to do it. The expected way to get CPU ID while allowing
for migration is to use raw_smp_processor_id.
In order to make this future-proof this patch keeps CPU_SEQID as is and
introduces CPU_SEQID_UNSTABLE instead, to make it clear that consumers
explicitly want this behavior.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11142
The zfs_holey() and zfs_access() functions can be made common
to both FreeBSD and Linux.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11125
zvol private data is supposed to be nulled by zvol_clear_private before
zvol_free is called as an indicator that the zvol is going away.
Implement zvol_clear_private for volmode=dev.
Assert that zvol_clear_private has been called before zvol_free.
Check that zvol_clear_private has not been called when updating
volsize. If it has, fail with ENXIO.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Make sure to free doi in zvol_create_minor impl when make_dev_s fails.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
We fall back to a default volmode and continue when looking up a zvol's
volmode property fails. After this we should set the error to 0 to
ensure we take the success paths in the out section.
While here, make sure we only log that the zvol was created on success.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Nonfunctional changes for readability and consistency.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
zvol_geom_close gets a count of the number of close operations to do.
Make sure we're always using this count to check if this will be the
last close operation performed on the zvol.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Using more specific assert variants gives better messages on failure.
No functional change.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11117
Note that this only tracks sizes as requested by the caller.
Actual allocated space will almost always be bigger (e.g., rounded up to
the next power of 2 or page size). Additionally the allocated buffer may
be holding other areas hostage. Nonetheless, this is a starting point
for tracking memory usage in zstd.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11129
While evaluating other assembler implementations it turns out that
the precomputed hash subkey tables vary in size, from 8*16 bytes
(avx2/avx512) up to 48*16 bytes (avx512-vaes), depending on the
implementation.
To be able to handle the size differences later, allocate
`gcm_Htable` dynamically rather then having a fixed size array, and
adapt consumers.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11102
While preparing #9749 some .cfi_{start,end}proc directives
were missed. Add the missing ones.
See upstream https://github.com/openssl/openssl/commit/275a048f
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Attila Fülöp <attila@fueloep.org>
Closes#11101
AT_BENEATH was merged to stable/12, where kern_unlinkat takes a
non-const path. DECONST the path passed to kern_unlinkat in the
case where AT_BENEATH is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11139
The original xuio zero copy functionality has always been unused
on Linux and FreeBSD. Remove this disabled code to avoid any
confusion and improve readability.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11124
L2ARC devices of several terabytes filled with 4KB blocks may take 15
minutes to rebuild. Due to the way L2ARC log reading is implemented
it is quite likely that for all that time rebuild thread will never
sleep. At least on FreeBSD kernel threads have absolute priority and
can not be preempted by threads with lower priorities. If some thread
is also bound to that specific CPU it may not get any CPU time for all
the 15 minutes.
Reviewed-by: Cedric Berger <cedric@precidata.com>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11116
Refer to the correct section or alternative for FreeBSD and Linux.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11132
ZFS always waits for the write completion before flushing the cache.
That is why it does not require explicit ordering fences around it,
which are pretty difficult to implement for NVMe, since one has no
internal concept of strict request ordering.
This was already removed from FreeBSD once, but got resurrected
by mistake during OpenZFS merge.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#11130
The port removed provisions for zfs_znode_move but the cleanup missed
this bit. To quote the original:
[snip]
list_insert_tail(&zfsvfs->z_all_znodes, zp);
membar_producer();
/*
* Everything else must be valid before assigning z_zfsvfs makes the
* znode eligible for zfs_znode_move().
*/
zp->z_zfsvfs = zfsvfs;
[/snip]
In the current code it is immediately followed by unlock which issues
the same fence, thus plays no role in correctness.
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11115
The allocator does not provide the functionality to begin with.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11114
The Linux kernel MODULE_LICENSE macro only recognizes a handful of
license strings and "MIT" is not one of the them. Update the macro
to use "Dual MIT/GPL" which is recognized and what the kernel expects
MIT licensed modules to use.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11112Closes#11113
These kstats are often expensive to compute so we want to avoid them
unless specifically requested.
The following kstats are affected by this change:
kstat.zfs.${pool}.multihost
kstat.zfs.${pool}.misc.state
kstat.zfs.${pool}.txgs
kstat.zfs.misc.fletcher_4_bench
kstat.zfs.misc.vdev_raidz_bench
kstat.zfs.misc.dbufs
kstat.zfs.misc.dbgmsg
In FreeBSD 13, sysctl(8) has been updated to still list the
names/description/type of skipped sysctls so they are still
discoverable.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11099
It's even documented already.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11094
The zfs_fsync, zfs_read, and zfs_write function are almost identical
between Linux and FreeBSD. With a little refactoring they can be
moved to the common code which is what is done by this commit.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11078
The current l2_misses accounting behavior treats all reads to pools
without a configured l2arc as an l2arc miss, IFF there is at least
one other pool on the system which does have an l2arc configured.
This makes it extremely hard to tune for an improved l2arc hit/miss
ratio because this ratio will be modulated by reads from pools which
do not (and should not) have l2arc devices; its upper limit will
depend on the ratio of reads from l2arc'd pools and non-l2arc'd pools.
This PR prevents ARC reads affecting l2arc stats (n.b. l2_misses is
the only relevant one) where the target spa doesn't have an l2arc.
Includes new test - l2arc_l2miss_pos.ksh
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Amanakis <gamanakis@gmail.com>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#10921
This was removed in a reorganization of directories preparing for the
merge of FreeBSD support, 006e9a4088 by mmacy. While llvm is perfectly
happy with the nonexistent -I directory, the gcc6 and gcc9 we can elect
to use as cross-toolchains both trip over it.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Closes#11077
zfs_onexit_os.c was not deleted when it was removed from the build
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11079
Otherwise lookup can fail with EOPNOTSUPP or panic.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11066
The removal of a vdev in the normal class would fail if there was a
special or deup vdev that had a different ashift than the vdevs in
the normal class.
Moved the initialization of spa_min_ashift / spa_max_ashift from
vdev_open so that it occurs after the vdev allocation bias was
initialized (i.e. after vdev_load).
Caveat -- In order to remove a special/dedup vdev it must have the
same ashift as the normal pool vdevs. This could perhaps be lifted
in the future (i.e. for the case where there is ample space in any
surviving special class vdevs)
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#9363Closes#9364Closes#11053
This is a follow up fix for commit 0fdd6106bb. The VERIFY is
only true when we haven't hit an error code path. See added
test case for a reproducer.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11048
After a side-effectful call like add or remove, references to range
segs stored in btrees can no longer be used safely. We move the
remove call to just before the reinsertion call so that the seg
remains valid for as long as we need it.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#11044Closes#11056
The 32-bit counter eventually wraps to 0 which is a sentinel for invalid
id.
Make it 64-bit on LP64 platforms and 0-check otherwise.
Note: Linux counterpart uses id stored per queue instead of a global.
I did not check going that way is feasible with the goal being the
minimal fix doing the job.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#11059
The acltype property is currently hidden on FreeBSD and does not
reflect the NFSv4 style ZFS ACLs used on the platform. This makes it
difficult to observe that a pool imported from FreeBSD on Linux has a
different type of ACL that is being ignored, and vice versa.
Add an nfsv4 acltype and expose the property on FreeBSD.
Make the default acltype nfsv4 on FreeBSD.
Setting acltype to an unhanded style is treated the same as setting
it to off. The ACLs will not be removed, but they will be ignored.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10520
In FreeBSD, there are three compile environments that are supported:
user land, the kernel and the bootloader / standalone. Adjust the
headers to compile in the standalone environment. Limit kernel-only
items from view when _STANDALONE is defined.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Warner Losh <imp@FreeBSD.org>
Closes#10998
Currently streams are only freed when:
- They have no referencing zfetch and and their I/O references
go to zero.
- They are more than 2s old and a new I/O request comes in on
the same zfetch.
This means that we will leak unreferenced streams when their zfetch
structure is freed.
This change checks the reference count on a stream at zfetch free
time. If it is zero we free it immediately. If it has remaining
references we allow the prefetch callback to free it at I/O
completion time.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#11052
The zstd code assumes that if you are on aarch64, you have NEON
instructions. This is not necessarily true. In a boot loader, where
you might not have the VFP properly initialized, these instructions
may not be available. It's also an error to include arm_neon.h when
the NEON insturctions aren't enabled. Change the guards for using the
NEON instructions from __aarch64__ to __ARM_NEON which is the standard
symbol for knowing if they are available.
__ARM_NEON is the proper symbol, defined in ARM C Language Extensions
Release 2.1 (https://developer.arm.com/documentation/ihi0053/d/). Some
sources suggest __ARM_NEON__, but that's the obsolete spelling from
prior versions of the standard.
Updated based on zstd pull request https://github.com/facebook/zstd/pull/2356
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Closes#11055
FreeBSD had this value tunable before the switch to the new OpenZFS.
The tunable name has changed, breaking legacy compat.
Restore legacy compat for this tunable, properly expose the tunable
with the new name on all platforms, and document it in
zfs-module-parameters(5).
While here, clean up the documentation for zfetch_max_distance a bit.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11038
Code cleanup, a follow up commit to 4d55ea81.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Co-authored-by: Ryan Moeller <ryan@freqlabs.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#11020
The value of zp is used without having been initialized under some
conditions. Initialize the pointer to NULL.
Add a regression test case using chown in acl/posix. However, this is
not enough because the setup sets xattr=sa, which means zfs_setattr_dir
will not be called. Create a second group of acl tests in acl/posix-sa
duplicating the acl/posix tests with symlinks, and remove xattr=sa from
the original acl/posix tests. This provides more coverage for the
default xattr=on code.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10043Closes#11025
This change updates the documentation to refer to the project
as OpenZFS instead ZFS on Linux. Web links have been updated
to refer to https://github.com/openzfs/zfs. The extraneous
zfsonlinux.org web links in the ZED and SPL sources have been
dropped.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Richard Laager <rlaager@wiktel.com>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#11007
A missing semicolon between kmoddir variable declaration and the
uninstall for loop caused modules_uninstall-Linux to fail with:
Syntax error: "do" unexpected
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Jacob Adams <jacob@tookmund.com>
Closes#11032
When running libzpool with the Undefined Behavior Sanitizer (ubsan)
enabled, a zpool create causes a run-time error:
module/zfs/vdev_label.c:600:14: runtime error: shift exponent 64 is
too large for 64-bit type 'long long unsigned int'`
in vdev_config_generate()
Fix is to convert vdev_removal_max_span to its base-2 logarithm, using
highbit64(), and then compare the "shifts".
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Chuck Tuffli <ctuffli@gmail.com>
Closes#9744Closes#11024
With procfs_list kstats implemented for FreeBSD, dbufs are now exposed
as kstat.zfs.misc.dbufs.
On FreeBSD, dbufstats can use the sysctl instead of procfs when no
input file has been given.
Enable the dbufstats tests on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11008
Code cleanup. Sort includes, remove duplicates, and drop
some extra blank lines in kmod_core.c.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#11000
Instead of relying on arbitrary timers after pool export/import or cache
device off/online rely on arcstats. This makes the L2ARC tests more
robust. Also cleanup some functions related to persistent L2ARC.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Adam Moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10983
We were missing an include for kernel FPU functions, breaking the build
on FreeBSD 12.1-RELEASE. This was apparently being pulled in from
elsewhere on stable/12 and head.
Sorted the other includes in these files while here.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#11005
In C, const indicates to the reader that mutation will not occur.
It can also serve as a hint about ownership.
Add const in a few places where it makes sense.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10997
This causes "zfs send -vt ..." to fail with:
cannot resume send: Unknown error 1030
It turns out that some of the name/value pairs in the verification
list for zfs_ioc_send_space(), zfs_keys_send_space, had the wrong
name, so the ioctl got kicked out in zfs_check_input_nvpairs().
Update the names accordingly.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10978
The kernel seq_read() helper function expects ->next() to update
the passed position even there are no more entries. Failure to
do so results in the following warning being logged.
seq_file: buggy .next function procfs_list_seq_next [spl]
did not update position index
Functionally there is no issue with the way procfs_list_seq_next()
is implemented and the warning is harmless. However, we want to
silence this some what scary incorrect warning. This commit
updates the Linux procfs code to advance the position even for
the last entry.
Reviewed-by: Tony Hutter <hutter2@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10984Closes#10996
The request number is out of bounds of the platform table.
Subtract the starting offset to get the correct subscript.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10994
`dbuf_stats_hash_table_data` can take much longer than it needs to
by repeatedly bzeroing its buffer when in fact the buffer only needs
to be NULL terminated.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10993
In non regular use cases allocated memory might stay persistent in memory
pool. This small patch checks every minute if there are old objects which
can be released from memory pool.
Right now with regular use, the pool is checked for old objects on each
allocation attempt from this pool. so basically polling by its use. Now
consider what happens if someone writes a lot of files and stops use of
the volume or even unmounts it. So the code will no longer check if
objects can be released from the pool. Already allocated objects will
still stay in pool cache. this is no big issue for common use. But
someone discovered this issue while doing tests. personally i know this
behavior and I'm aware of it. Its no big issue. just a enhancement
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#10938Closes#10969
When an invalid incremental send is requested where the "to" ds is
before the "from" ds, make sure to drop the reference to the pool
and the dataset before returning the error.
Add an assert on FreeBSD to make sure we don't hold any locks after
returning from an ioctl.
Add some test coverage.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10919
The Linux kernel MODULE_LICENSE macro only recognizes a handful of
license strings and "BSD" is not one of the them. Update the macro
to use "Dual BSD/GPL" which is recognized and what the kernel expects
BSD licensed module to use.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10982Closes#10992
The current dmu_zfetch code implicitly assumes that I/Os complete
within min_sec_reap seconds. With async dmu and a readonly workload
(and thus no exponential backoff in operations from the "write
throttle") such as L2ARC rebuild it is possible to saturate the drives
with I/O requests. These are then effectively compounded with prefetch
requests.
This change reference counts streams and prevents them from being
recycled after their min_sec_reap timeout if they still have
outstanding I/Os.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10900
Prefetching of dnodes in dbuf_read() can cause significant mutex
contention for some workloads and isn't very helpful. This is
because we already get 32 dnodes for each block read, and when
iterating over a directory we prefetch the dnodes in the directory.
Disable this prefetching to prevent the lock contention.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Submitted-by: Adam Moss <c@yotes.com>
Submitted-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Adam Moss <c@yotes.com>
Closes#10877Closes#10953
With PREEMPTION=y and BLK_CGROUP=y preempt_schedule_notrace() is being
used on arm64 which is a GPL-only function and hence the build of the
DKMS kernel module fails.
Fix that by redefining preempt_schedule_notrace() to preempt_schedule()
which should be safe as long as tracing is not used.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Closes#8545Closes#9948Closes#10416Closes#10973
Address some unused value and control flow issues flagged by Coverity.
Unreachable code is pruned and unused values are avoided.
Some scattered sections are reordered for coherence.
We can assume kmem_alloc(n, KM_SLEEP) doesn't fail, so there is no need
to check if it returned NULL. The allocated memory doesn't need to be
zeroed, other than the last iovec (the MAC).
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10884
wkey is NULL at every `goto error;`.
dcp is never NULL.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10884
lr_write_t records that are WR_COPIED have the record data directly
appended to them (see lr_write_t type definition).
The data is copied from the debuf using dmu_read_by_dnode.
This function was called, only for WR_COPIED records, as part of a
short-circuiting if-statement's if-expression.
I found this side-effectful call to dmu_read_by_dnode pretty
hard to spot.
This patch improves readability by moving the call to its own line.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: George Wilson <gwilson@delphix.com>
Signed-off-by: Christian Schwarz <me@cschwarz.com>
Closes#10956
The procfs_list interface is required by several kstats. Implement
this functionality for FreeBSD to provide access to these kstats.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10890
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10899
Resolves an issue with `zfs send` streams from 0.8.4 which
prevents them from being received by versions < 0.7.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10911Closes#10916
Commit 45152dc removed clearing of L2CACHE flag in arc_read_done() and
moved related code in l2arc_write_eligible(). After careful code
inspection arc_read_done() is not bypassed in the case of prefetches.
Thus restore the old behavior.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: adam moss <c@yotes.com>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10951
In commit cd32b4f5b7 ("Fix a deadlock in the FreeBSD getpages VOP") I
introduced a bug while porting the patch originally committed to
FreeBSD: the rangelock pointer may be NULL if the try operation failed,
so we must avoid calling zfs_rangelock_unlock() in that case.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Reported-by: Steve Wills <swills@FreeBSD.org>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10519Closes#10960
Use the same reduced buffer size for lauxlib that is used on Linux.
Fixes panic on HEAD in lua gsub test designed to exhaust stack space.
With this we can remove the special case to reserve more stack space
on FreeBSD.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10959
Without this, the sysctl system calls will acquire a global lock before
invoking the handler. This is noticeable in some situations when
running top(1). The global lock is mostly vestigal but continues to see
some use and so contention is still a problem; until the default sense
of the MPSAFE flag changes, we have to annotate each and every handler.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10836
This is in preparation for some functional changes.
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Signed-off-by: Mark Johnston <markj@FreeBSD.org>
Closes#10950
== Motivation and Context
The new vdev ashift optimization prevents the removal of devices when
a zfs configuration is comprised of disks which have different logical
and physical block sizes. This is caused because we set 'spa_min_ashift'
in vdev_open and then later call 'vdev_ashift_optimize'. This would
result in an inconsistency between spa's ashift calculations and that
of the top-level vdev.
In addition, the optimization logical ignores the overridden ashift
value that would be provided by '-o ashift=<val>'.
== Description
This change reworks the vdev ashift optimization so that it's only
set the first time the device is configured. It still allows the
physical and logical ahsift values to be set every time the device
is opened but those values are only consulted on first open.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Cedric Berger <cedric@precidata.com>
Signed-off-by: George Wilson <gwilson@delphix.com>
External-Issue: DLPX-71831
Closes#10932
When expanding a device zfs needs to rescan the partition table to
get the correct size. This can only happen when we're in the kernel
and requires the device to be closed. As part of the rescan, udev is
notified and the device links are removed and recreated. This leave a
window where the vdev code may try to reopen the device before udev
has recreated the link. If that happens, then the pool may end up in
a suspended state.
To correct this, we leverage the BLKPG_RESIZE_PARTITION ioctl which
allows the partition information to be modified even while it's in use.
This ioctl also does not remove the device link associated with the zfs
data partition so it eliminates the race condition that can occur in
the kernel.
Reviewed-by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Wilson <gwilson@delphix.com>
Closes#10897
https://reviews.freebsd.org/D26346
Do not copy vp into f_data for DTYPE_VNODE files. The vnode pointer is
already stored in f_vnode. Use that so f_data can be reused.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10929
In zpl_mount_impl, there is:
dmu_objset_hold ; returns with pool & ds held
dsl_pool_rele
sget
dsl_dataset_rele
As spelled out in the "DSL Pool Configuration Lock" in dsl_pool.c,
this requires a long hold.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Paul Zuchowski <pzuchowski@datto.com>
Signed-off-by: John Poduska <jpoduska@datto.com>
Closes#10936
Prefer acltype=off|posix, retaining the old names as aliases.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10918
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#10879
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#10879
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#10879
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Pavel Snajdr <snajpa@snajpa.net>
Closes#10879
nvlist does allow us to support different data types and systems.
To encapsulate user data to/from nvlist, the libzfsbootenv library is
provided.
Reviewed-by: Arvind Sankar <nivedita@alum.mit.edu>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Paul Dagnelie <pcd@delphix.com>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10774
Use ZFS_ENTER and ZFS_EXIT to protect datasets while their mount
devname is being retrieved.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10892Closes#10927
Currently the ARC state (MFU/MRU) of cached L2ARC buffer and their
content type is unknown. Knowing this information may prove beneficial
in adjusting the L2ARC caching policy.
This commit adds L2ARC arcstats that display the aligned size
(in bytes) of L2ARC buffers according to their content type
(data/metadata) and according to their ARC state (MRU/MFU or
prefetch). It also expands the existing evict_l2_eligible arcstat to
differentiate between MFU and MRU buffers.
L2ARC caches buffers from the MRU and MFU lists of ARC. Upon caching a
buffer, its ARC state (MRU/MFU) is stored in the L2 header
(b_arcs_state). The l2_m{f,r}u_asize arcstats reflect the aligned size
(in bytes) of L2ARC buffers according to their ARC state (based on
b_arcs_state). We also account for the case where an L2ARC and ARC
cached MRU or MRU_ghost buffer transitions to MFU. The l2_prefetch_asize
reflects the alinged size (in bytes) of L2ARC buffers that were cached
while they had the prefetch flag set in ARC. This is dynamically updated
as the prefetch flag of L2ARC buffers changes.
When buffers are evicted from ARC, if they are determined to be L2ARC
eligible then their logical size is recorded in
evict_l2_eligible_m{r,f}u arcstats according to their ARC state upon
eviction.
Persistent L2ARC:
When committing an L2ARC buffer to a log block (L2ARC metadata) its
b_arcs_state and prefetch flag is also stored. If the buffer changes
its arcstate or prefetch flag this is reflected in the above arcstats.
However, the L2ARC metadata cannot currently be updated to reflect this
change.
Example: L2ARC caches an MRU buffer. L2ARC metadata and arcstats count
this as an MRU buffer. The buffer transitions to MFU. The arcstats are
updated to reflect this. Upon pool re-import or on/offlining the L2ARC
device the arcstats are cleared and the buffer will now be counted as an
MRU buffer, as the L2ARC metadata were not updated.
Bug fix:
- If l2arc_noprefetch is set, arc_read_done clears the L2CACHE flag of
an ARC buffer. However, prefetches may be issued in a way that
arc_read_done() is bypassed. Instead, move the related code in
l2arc_write_eligible() to account for those cases too.
Also add a test and update manpages for l2arc_mfuonly module parameter,
and update the manpages and code comments for l2arc_noprefetch.
Move persist_l2arc tests to l2arc.
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10743
The lock is taken all the time and as a regular read-write lock
avoidably serves as a mount point-wide contention point.
This forward ports FreeBSD revision r357322.
To quote aforementioned commit:
Sample result doing an incremental -j 40 build:
before: 173.30s user 458.97s system 2595% cpu 24.358 total
after: 168.58s user 254.92s system 2211% cpu 19.147 total
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Closes#10896
A great deal of time may go by between when mmp_init() is called and
the MMP thread starts, particularly if there are bad devices, because
there is I/O checking configs etc. If this time is too long,
(gethrtime() - mmp_last_write) > mmp_fail_ns
at the time the MMP thread starts. If MMP is configured to suspend
the pool, the pool will be suspended immediately.
This can be seen in issue #10838
The value of mmp_last_write doesn't matter before the mmp thread
starts. To give the MMP thread time to issue and land MMP writes,
initialize mmp_last_write when the MMP thread starts.
Reviewed-by: Giuseppe Di Natale <guss80@gmail.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Olaf Faaland <faaland1@llnl.gov>
Closes#10873
We only need the kernel interfaces in crypto, not the device node in
cryptodev.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10901
In certain workloads it may be beneficial to reduce wear of L2ARC
devices by not caching MRU metadata and data into L2ARC. This commit
introduces a new tunable l2arc_mfuonly for this purpose.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Closes#10710
On FreeBSD, if priorities divided by four (RQ_PPQ) are equal then
a difference between them is insignificant. In other words,
incrementing pri by only one as on Linux is insufficient.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10872
Commit d4a72f2 which introduced multi-phase scrubs and resilvers
continued the work presented by Nexenta at the 2016 ZFS developer
summit. Update the source to reflect their contribution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Duplicate io and checksum ereport events can misrepresent that
things are worse than they seem. Ideally the zpool events and the
corresponding vdev stat error counts in a zpool status should be
for unique errors -- not the same error being counted over and over.
This can be demonstrated in a simple example. With a single bad
block in a datafile and just 5 reads of the file we end up with a
degraded vdev, even though there is only one unique error in the pool.
The proposed solution to the above issue, is to eliminate duplicates
when posting events and when updating vdev error stats. We now save
recent error events of interest when posting events so that we can
easily check for duplicates when posting an error.
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Don Brady <don.brady@delphix.com>
Closes#10861
If a `zfs_space_check_t` other than `ZFS_SPACE_CHECK_NONE` is used with
`dsl_sync_task_nowait()`, the sync task may fail due to ENOSPC.
However, there is no way to notice or communicate this failure, so it's
extremely difficult to use this functionality correctly, and in fact
almost all callers use `ZFS_SPACE_CHECK_NONE`.
This commit removes the `zfs_space_check_t` argument from
`dsl_sync_task_nowait()`, and always uses `ZFS_SPACE_CHECK_NONE`.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10855
When created, a zthr is given a name to identify it by. This name is
lost when a cancelled zthr is resumed.
Retain the name of a zthr so it can be used when resuming.
Reviewed-by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10881
There are a number of places where cv_?_sig is used simply for
accounting purposes but the surrounding code has no ability to
cope with actually receiving a signal. On FreeBSD it is possible
to send signals to individual kernel threads so this could
enable undesirable behavior.
This patch adds routines on Linux that will do the same idle
accounting as _sig without making the task interruptible. On
FreeBSD cv_*_idle are all aliases for cv_*
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10843
Added comments in following files
with links to Illumos manual pages:
./module/avl/avl.c
./module/nvpair/nvpair.c
./module/os/linux/spl/spl-kstat.c
./module/os/freebsd/spl/spl_kstat.c
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Spencer Kinny <spencerkinny1995@gmail.com>
Closes#5113Closes#10859
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10867
Use ZFS_MODULE_PARAM for cross-platform tunables in spa_stats.c, and
add update tunables.cfg in tests for the newly supported ones.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10858
Moving spa_stats added the additional burden of supporting
KSTAT_TYPE_IO.
spa_state_addr will always return a valid value regardless of
the value of 'n'. On FreeBSD this will cause an infinite loop
as it relies on the raw ops addr routine to indicate that there
is no more data.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10860
Allow to rename file systems without remounting if it is possible.
It is possible for file systems with 'mountpoint' property set to
'legacy' or 'none' - we don't have to change mount directory for them.
Currently such file systems are unmounted on rename and not even
mounted back.
This introduces layering violation, as we need to update
'f_mntfromname' field in statfs structure related to mountpoint (for
the dataset we are renaming and all its children).
In my opinion it is worth it, as it allow to update FreeBSD in even
cleaner way - in ZFS-only configuration root file system is ZFS file
system with 'mountpoint' property set to 'legacy'. If root dataset is
named system/rootfs, we can snapshot it (system/rootfs@upgrade), clone
it (system/oldrootfs), update FreeBSD and if it doesn't boot we can
boot back from system/oldrootfs and rename it back to system/rootfs
while it is mounted as /. Before it was not possible, because
unmounting / was not possible.
Authored by: Pawel Jakub Dawidek <pjd@FreeBSD.org>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Ported by: Matt Macy <mmacy@freebsd.org>
Signed-off-by: Ryan Moeller <ryan@iXsystems.com>
Closes#10839
SECLABEL is undefined on FreeBSD and should be pruned.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10847
FreeBSD's previous ZFS implemented INGLOBALZONE(thread) as
(!jailed((thread)->td_ucred)) and passed curthread to INGLOBALZONE.
We pass curproc instead of curthread, so we can achieve the same effect
with (!jailed((proc)->p_ucred)). The implementation is trivial enough
to fit on a single line in a define. We don't really need a whole
separate function for something that's already macros all the way down.
Eliminate in_globalzone.
Reviewed-by: Alexander Motin <mav@FreeBSD.org>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Ryan Moeller <freqlabs@FreeBSD.org>
Closes#10851
use (void) to silence analyzers.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10857
Initially it was considered simplest to stub out all
of the functions on FreeBSD. Now that FreeBSD supports
KSTAT_TYPE_RAW at least some of the functionality should
be made available.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10842
In zvol_geom_open on first open we need to guarantee
that the namespace lock is held to avoid spurious
failures in zvol_first_open.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <freqlabs@FreeBSD.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10841
A few kstats use KSTAT_TYPE_RAW to provide a string generated on
demand. Implementing these as sysctls was punted until now.
Reviewed by: Toomas Soome <tsoome@me.com>
Reviewed-by: Allan Jude <allan@klarasystems.com>
Reviewed-by: Ryan Moeller <ryan@ixsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10836
Commit dcdc12e added compatibility code to treat NR_SLAB_RECLAIMABLE_B
as if it were the same as NR_SLAB_RECLAIMABLE. However, the new value
is in bytes while the old value was in pages which means they are not
interchangeable.
The only place the reclaimable slab size is used is as a component of
the calculation done by arc_free_memory(). This function returns the
amount of memory the ARC considers to be free or reclaimable at little
cost. Rather than switch to a new interface to get this value it has
been removed it from the calculation. It is normally a minor component
compared to the number of inactive or free pages, and removing it
aligns the behavior with the FreeBSD version of arc_free_memory().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Coleman Kane <ckane@colemankane.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10834
If kernel is compiled with -march=znver1 or -march=znver2 zstd module
compilation will fail due to SSE register return with SSE disabled.
What's interesting, is that -march=skylake also implies -mbmi which
defines __BMI__ but compilation succeeds. It is probably due to
different BMI implementations on AMD and INTEL processors and the
way compiler uses instructions.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Georgy Yakovlev <gyakovlev@gentoo.org>
Closes#10758Closes#10829
Because dnode_sync_free_range() must drop dn_mtx during its processing,
using it as a callback to range_tree_vacate() is not safe. No other
operations (besides destroy) are allowed once range_tree_vacate() has
begun, and dropping dn_mtx would leave a window open for another thread
to observe that invalid (and unsafe) state via dnode_block_freed().
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Igor Kozhukhov <igor@dilos.org>
Signed-off-by: Patrick Mooney <pmooney@oxide.computer>
Closes#10708Closes#10823
The zfs/sa.c source file accidentally includes sys/dnode.h twice.
Remove the second occurrence.
Reviewed-by: Matthew Ahrens <mahrens@delphix.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10816Closes#10819
The root cause of the issue is that we only occasionally do as the
comments in the code suggest and actually ignore the %recv dataset when
it comes to filesystem limit tracking. Specifically, the only time we
ignore it is when initializing the filesystem and snapshot limit values;
when creating a new %recv dataset or deleting one, we always update
the bookkeeping. This causes a problem if you init the fs count on a
filesystem that already has a %recv dataset, since the bookmarking
will be decremented but not incremented. This is resolved in this
patch by simply always tracking the %recv dataset as a child.
Reviewed-by: Matt Ahrens <matt@delphix.com>
Reviewed by: Jerry Jelinek <jerry.jelinek@joyent.com>
Signed-off-by: Paul Dagnelie <pcd@delphix.com>
Closes#10791
The #pragma ident is a historical relic and not needed any more, this
pragma is actually unknown for common compilers and is only causing
trouble.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Matt Macy <mmacy@FreeBSD.org>
Signed-off-by: Toomas Soome <tsoome@me.com>
Closes#10810
The neon support code does not build on FreeBSD,
ifdef out references to fix linker issues on arm64.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10809
Since L2ARC buffers are not evicted on memory pressure, too large
amount of headers on system with irrationally large L2ARC can render
it slow or even unusable. This change limits L2ARC writes and
rebuild if unevictable L2ARC-only headers reach dangerous level.
While there, call arc_adapt() on L2ARC rebuild, so that it could
properly grow arc_c, reflecting potentially significant ARC size
increase and avoiding slow growth with hopeless eviction attempts
later when "overflow" is detected.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Richard Elling <Richard.Elling@RichardElling.com>
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Closes#10765
Linux already defines setjmp/longjmp for powerpc, which leads to
duplicate symbols in a statically linked build.
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sterlng Jensen <sterlingjensen@users.noreply.github.com>
Closes#10795
Export the dmu_offset_next() symbol for use by Lustre.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#10796
The cache of struct svc_export and struct svc_expkey by nfsd and
rpc.mountd for the snapshot holds references to the mount point.
We need to flush them out before unmounting, otherwise umount
would fail with EBUSY.
Reviewed-by: Don Brady <don.brady@delphix.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Youzhong Yang <yyang@mathworks.com>
Closes#6000Closes#10783
For Linux, when zfs is compiled as an in kernel static variant
and the in kernel zstd library is compiled statically into the kernel
a symbol collision will occur. This wrapper header renames all
of the relevant zstd functions to avoid this problem.
Reviewed-by: Kjeld Schouten <kjeld@schouten-lebbing.nl>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Closes#10775
In absence of inheriting entry for owner@, group@, or everyone@,
zfs_acl_chmod() is called to set these. This can cause confusion for Samba
admins who do not expect these entries to appear on newly created files and
directories once they have been stripped from from the parent directory.
When aclmode is set to "restricted", chmod is prevented on non-trivial ACLs.
It is not a stretch to assume that in this case the administrator does not want
ZFS to add the missing special entries. Add check for this aclmode, and if an
inherited entry is present skip zfs_acl_chmod().
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Andrew Walker <awalker@ixsystems.com>
Closes#10748
All other prop values return options separated by ` | `,
dedup values do not, they are separated by `, `. This change
makes the dedup value formatting consistent with other properties.
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Signed-off-by: Clint Armstrong <clint@clintarmstrong.net>
Closes#10761
Many modern devices use physical allocation units that are much
larger than the minimum logical allocation size accessible by
external commands. Two prevalent examples of this are 512e disk
drives (512b logical sector, 4K physical sector) and flash devices
(512b logical sector, 4K or larger allocation block size, and 128k
or larger erase block size). Operations that modify less than the
physical sector size result in a costly read-modify-write or garbage
collection sequence on these devices.
Simply exporting the true physical sector of the device to ZFS would
yield optimal performance, but has two serious drawbacks:
1. Existing pools created with devices that have different logical
and physical block sizes, but were configured to use the logical
block size (e.g. because the OS version used for pool construction
reported the logical block size instead of the physical block
size) will suddenly find that the vdev allocation size has
increased. This can be easily tolerated for active members of
the array, but ZFS would prevent replacement of a vdev with
another identical device because it now appears that the smaller
allocation size required by the pool is not supported by the new
device.
2. The device's physical block size may be too large to be supported
by ZFS. The optimal allocation size for the vdev may be quite
large. For example, a RAID controller may export a vdev that
requires read-modify-write cycles unless accessed using 64k
aligned/sized requests. ZFS currently has an 8k minimum block
size limit.
Reporting both the logical and physical allocation sizes for vdevs
solves these problems. A device may be used so long as the logical
block size is compatible with the configuration. By comparing the
logical and physical block sizes, new configurations can be optimized
and administrators can be notified of any existing pools that are
sub-optimal.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Matthew Macy <mmacy@freebsd.org>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10619
Reviewed-by: George Melikov <mail@gmelikov.ru>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matthew Ahrens <mahrens@delphix.com>
Closes#10744
Removing other_size from arc_stats breaks top in 11.x jails
running on HEAD.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Matt Macy <mmacy@FreeBSD.org>
Closes#10745
This PR adds two new compression types, based on ZStandard:
- zstd: A basic ZStandard compression algorithm Available compression.
Levels for zstd are zstd-1 through zstd-19, where the compression
increases with every level, but speed decreases.
- zstd-fast: A faster version of the ZStandard compression algorithm
zstd-fast is basically a "negative" level of zstd. The compression
decreases with every level, but speed increases.
Available compression levels for zstd-fast:
- zstd-fast-1 through zstd-fast-10
- zstd-fast-20 through zstd-fast-100 (in increments of 10)
- zstd-fast-500 and zstd-fast-1000
For more information check the man page.
Implementation details:
Rather than treat each level of zstd as a different algorithm (as was
done historically with gzip), the block pointer `enum zio_compress`
value is simply zstd for all levels, including zstd-fast, since they all
use the same decompression function.
The compress= property (a 64bit unsigned integer) uses the lower 7 bits
to store the compression algorithm (matching the number of bits used in
a block pointer, as the 8th bit was borrowed for embedded block
pointers). The upper bits are used to store the compression level.
It is necessary to be able to determine what compression level was used
when later reading a block back, so the concept used in LZ4, where the
first 32bits of the on-disk value are the size of the compressed data
(since the allocation is rounded up to the nearest ashift), was
extended, and we store the version of ZSTD and the level as well as the
compressed size. This value is returned when decompressing a block, so
that if the block needs to be recompressed (L2ARC, nop-write, etc), that
the same parameters will be used to result in the matching checksum.
All of the internal ZFS code ( `arc_buf_hdr_t`, `objset_t`,
`zio_prop_t`, etc.) uses the separated _compress and _complevel
variables. Only the properties ZAP contains the combined/bit-shifted
value. The combined value is split when the compression_changed_cb()
callback is called, and sets both objset members (os_compress and
os_complevel).
The userspace tools all use the combined/bit-shifted value.
Additional notes:
zdb can now also decode the ZSTD compression header (flag -Z) and
inspect the size, version and compression level saved in that header.
For each record, if it is ZSTD compressed, the parameters of the decoded
compression header get printed.
ZSTD is included with all current tests and new tests are added
as-needed.
Per-dataset feature flags now get activated when the property is set.
If a compression algorithm requires a feature flag, zfs activates the
feature when the property is set, rather than waiting for the first
block to be born. This is currently only used by zstd but can be
extended as needed.
Portions-Sponsored-By: The FreeBSD Foundation
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Brian Behlendorf <behlendorf1@llnl.gov>
Co-authored-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allan@klarasystems.com>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Closes#6247Closes#9024Closes#10277Closes#10278
ZStandard is a modern, high performance, general compression algorithm.
It provides similar or better compression levels to GZIP, but with much
better performance. ZStandard provides a large selection of compression
levels to allow a storage administrator to select the preferred
performance/compression trade-off.
This commit imports the unmodified ZStandard single-file library which
will be used by ZFS.
The implementation of this new library is done with future updates of
zstd in mind. For this reason we integrated the code in a way, that does
not require modifications to the library. For more details, see
`module/zstd/README.md`.
The library is excluded from codecov calculation and cppcheck as
unaltered dependencies do not need full codecov or cppcheck.
Co-authored-by: Allan Jude <allanjude@freebsd.org>
Co-authored-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Co-authored-by: Michael Niewöhner <foss@mniewoehner.de>
Signed-off-by: Allan Jude <allanjude@freebsd.org>
Signed-off-by: Kjeld Schouten-Lebbing <kjeld@schouten-lebbing.nl>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
This option is used by FreeBSD boot loader.
Reviewed-by: Ryan Moeller <ryan@iXsystems.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Signed-off-by: Mariusz Zaborski <oshogbo@vexillium.org>
Closes#10738
Brian Behlendorf
George Amanakis
Alexander Motin
Tino Reichardt
Andrew
crass
Damian Szuberski
Allan Jude
Ryan Moeller
Will Andrews
Tony Hutter
Kevin Jin
Paul Dagnelie
Rich Ercolani
наб
hping
Aidan Harris
Mateusz Guzik
Shaan Nobee
Pawel Jakub Dawidek
Jitendra Patidar
Satadru Pramanik
Mark Johnston
Jorgen Lundman
Riccardo Schirone
hpingfs
Kyle Evans
Brian Atkinson
Akash B
Attila Fülöp
Umer Saleem
Alejandro Colomar
Rich Ercolani
Ryan Moeller
drowfx
Peter Levine
Tomohiro Kusumi
Christian Schwarz
Finix1979
Mark Johnston
Mark Maybee
Tino Reichardt
chrisrd
Alan Somers
Coleman Kane
Paul Dagnelie
Fedor Uporov
Damian Szuberski
José Luis Salvador Rufo
Arun KV
Ka Ho Ng
Trevor Bautista
Richard Yao
Tony Nguyen
hedongzhang
Alexander
George Wilson
jumbi77
Antonio Russo
Matthew Ahrens
Paul Zuchowski
Serapheim Dimitropoulos
jharmening
vermavipinkumar
Alyssa Ross
Nathaniel Wesley Filardo
Martin Matuška
Romain Dolbeau
pstef
TerraTech
Andrea Gelmini
Luis Henriques
Alexander Motin
Chunwei Chen
Adam D. Moss
Don Brady
Mariusz Zaborski
Christian Schwarz
Jake Howard
nssrikanth
Andriy Gapon
Prakash Surya
fbynite
Ryan Libby
Colm
khng300
Kleber Tarcísio
Brian Atkinson
Alan Somers
Will Andrews
Matthew Macy
Konstantin Khorenko
Toomas Soome
Andy Fiddaman
Michael D Labriola
Ryan Libby
Finix1979
loli10K
Tony Perkins
Sebastian Gottschall
Warner Losh
Jacob Adams
Chuck Tuffli
John Poduska
Pavel Snajdr
Olaf Faaland
Spencer Kinny
Georgy Yakovlev
Patrick Mooney
sterlingjensen
youzhongyang
Clint Armstrong
Michael Niewöhner