torvalds/linux@adc0e91ab1 introduced
introduced d_make_root() as a replacement for d_alloc_root(). Further
commits appear to have removed d_alloc_root() from the Linux source
tree. This causes the following failure:
error: implicit declaration of function 'd_alloc_root'
[-Werror=implicit-function-declaration]
To correct this we update the code to use the current d_make_root()
interface for readability. Then we introduce an autotools check
to determine if d_make_root() is available. If it isn't then we
define some compatibility logic which used the older d_alloc_root()
interface.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#776
When a device is already open O_EXCL by another process the
`zpool import` will correctly fail. However, the default failure
message isn't very helpful. It may in fact be harmful if you
take its advise and destroy your pool.
cannot import 'tank': pool is busy
Destroy and re-create the pool from
a backup source.
Improve the error message in the EBUSY case to simply print a
message indicating that the devices are current in use. The user
will need to manually identify which process has the device open
exclusively and why.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
When creating pools short device names may be used when those
devices appear in certain well known locations under /dev/.
This change adds /dev/mapper/ to that list.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
vdev_id parses the file /etc/zfs/vdev_id.conf to map a physical path
in a storage topology to a channel name. The channel name is combined
with a disk enclosure slot number to create an alias that reflects the
physical location of the drive. This is particularly helpful when it
comes to tasks like replacing failed drives. Slot numbers may also be
re-mapped in case the default numbering is unsatisfactory. The drive
aliases will be created as symbolic links in /dev/disk/by-vdev.
The only currently supported topologies are sas_direct and sas_switch:
o sas_direct - a channel is uniquely identified by a PCI slot and a
HBA port
o sas_switch - a channel is uniquely identified by a SAS switch port
A multipath mode is supported in which dm-mpath devices are handled by
examining the first running component disk, as reported by 'multipath
-l'. In multipath mode the configuration file should contain a
channel definition with the same name for each path to a given
enclosure.
vdev_id can replace the existing zpool_id script on systems where the
storage topology conforms to sas_direct or sas_switch. The script
could be extended to support other topologies as well. The advantage
of vdev_id is that it is driven by a single static input file that can
be shared across multiple nodes having a common storage toplogy.
zpool_id, on the other hand, requires a unique /etc/zfs/zdev.conf per
node and a separate slot-mapping file. However, zpool_id provides the
flexibility of using any device names that show up in
/dev/disk/by-path, so it may still be needed on some systems.
vdev_id's functionality subsumes that of the sas_switch_id script, and
it is unlikely that anyone is using it, so sas_switch_id is removed.
Finally, /dev/disk/by-vdev is added to the list of directories that
'zpool import' will scan.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#713
The mode argument of iops->create()/mkdir()/mknod() was changed from
an 'int' to a 'umode_t'. To prevent a compiler warning an autoconf
check was added to detect the API change and then correctly set a
zpl_umode_t typedef. There is no functional change.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#701
Allow rigorous (and expensive) tx validation to be enabled/disabled
indepentantly from the standard zfs debugging. When enabled these
checks ensure that all txs are constructed properly and that a dbuf
is never dirtied without taking the correct tx hold.
This checking is particularly helpful when adding new dmu consumers
like Lustre. However, for established consumers such as the zpl
with no known outstanding tx construction problems this is just
overhead.
--enable-debug-dmu-tx - Enable/disable validation of each tx as
--disable-debug-dmu-tx it is constructed. By default validation
is disabled due to performance concerns.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add support for the .zfs control directory. This was accomplished
by leveraging as much of the existing ZFS infrastructure as posible
and updating it for Linux as required. The bulk of the core
functionality is now all there with the following limitations.
*) The .zfs/snapshot directory automount support requires a 2.6.37
or newer kernel. The exception is RHEL6.2 which has backported
the d_automount patches.
*) Creating/destroying/renaming snapshots with mkdir/rmdir/mv
in the .zfs/snapshot directory works as expected. However,
this functionality is only available to root until zfs
delegations are finished.
* mkdir - create a snapshot
* rmdir - destroy a snapshot
* mv - rename a snapshot
The following issues are known defeciences, but we expect them to
be addressed by future commits.
*) Add automount support for kernels older the 2.6.37. This should
be possible using follow_link() which is what Linux did before.
*) Accessing the .zfs/snapshot directory via NFS is not yet possible.
The majority of the ground work for this is complete. However,
finishing this work will require resolving some lingering
integration issues with the Linux NFS kernel server.
*) The .zfs/shares directory exists but no futher smb functionality
has yet been implemented.
Contributions-by: Rohan Puri <rohan.puri15@gmail.com>
Contributiobs-by: Andrew Barnes <barnes333@gmail.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#173
Some devices have exhibited sensitivity to the ending alignment of
partitions. In particular, even if the first partition begins at 1
MiB, we have seen many sd driver task abort errors with certain SSDs
if the first partition doesn't end on a 1 MiB boundary. This occurs
when the vdev label is read during pool creation or importation and
causes a delay of about 30 seconds per device. It can also be
simulated with dd when the pool isn't imported:
dd if=/dev/sda1 of=/dev/null bs=262144 count=1
For the record, this problem was observed with SMARTMOD
SG9XCA2E200GE01 200GB SSDs. Unfortunately I don't have a good
explanation for this behavior. It seems to have something to do with
highly fragmented single-sector requests being issued to the device,
which it may not support. With end-aligned partitions at least
page-sized requests were queued and issued to the driver according
to blktrace. In any case, aligning the partition end is a fairly
innocuous work-around, wasting at most 1 MiB of space.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#574
Allow a source rpm to be rebuilt with debugging enabled. This
avoids the need to have to manually modify the spec file. By
default debugging is still largely disabled. To enable specific
debugging features use the following options with rpmbuild.
'--with debug' - Enables ASSERTs
# For example:
$ rpmbuild --rebuild --with debug zfs-modules-0.6.0-rc6.src.rpm
Additionally, ZFS_CONFIG has been added to zfs_config.h for
packages which build against these headers. This is critical
to ensure both zfs and the dependant package are using the same
prototype and structure definitions.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
New SSDs are now available which use an internal 8k block size.
To make sure ZFS can get the maximum performance out of these
devices we're increasing the maximum ashift to 13 (8KB).
This value is still small enough that we can fit 16 uberblocks
in the vdev ring label. However, I don't want to increase this
any futher or it will limit the ability the safely roll back a
pool to recover it.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#565
DISCARD (REQ_DISCARD, BLKDISCARD) is useful for thin provisioning.
It allows ZVOL clients to discard (unmap, trim) block ranges from
a ZVOL, thus optimizing disk space usage by allowing a ZVOL to
shrink instead of just grow.
We can't use zfs_space() or zfs_freesp() here, since these functions
only work on regular files, not volumes. Fortunately we can use the
low-level function dmu_free_long_range() which does exactly what we
want.
Currently the discard operation is not added to the log. That's not
a big deal since losing discard requests cannot result in data
corruption. It would however result in disk space usage higher than
it should be. Thus adding log support to zvol_discard() is probably
a good idea for a future improvement.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Currently only the (FALLOC_FL_PUNCH_HOLE) flag combination is
supported, since it's the only one that matches the behavior of
zfs_space(). This makes it pretty much useless in its current
form, but it's a start.
To support other flag combinations we would need to modify
zfs_space() to make it more flexible, or emulate the desired
functionality in zpl_fallocate().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #334
The Linux block device queue subsystem exposes a number of configurable
settings described in Linux block/blk-settings.c. The defaults for these
settings are tuned for hard drives, and are not optimized for ZVOLs. Proper
configuration of these options would allow upper layers (I/O scheduler) to
take better decisions about write merging and ordering.
Detailed rationale:
- max_hw_sectors is set to unlimited (UINT_MAX). zvol_write() is able to
handle writes of any size, so there's no reason to impose a limit. Let the
upper layer decide.
- max_segments and max_segment_size are set to unlimited. zvol_write() will
copy the requests' contents into a dbuf anyway, so the number and size of
the segments are irrelevant. Let the upper layer decide.
- physical_block_size and io_opt are set to the ZVOL's block size. This
has the potential to somewhat alleviate issue #361 for ZVOLs, by warning
the upper layers that writes smaller than the volume's block size will be
slow.
- The NONROT flag is set to indicate this isn't a rotational device.
Although the backing zpool might be composed of rotational devices, the
resulting ZVOL often doesn't exhibit the same behavior due to the COW
mechanisms used by ZFS. Setting this flag will prevent upper layers from
making useless decisions (such as reordering writes) based on incorrect
assumptions about the behavior of the ZVOL.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zvol_write() assumes that the write request must be written to stable storage
if rq_is_sync() is true. Unfortunately, this assumption is incorrect. Indeed,
"sync" does *not* mean what we think it means in the context of the Linux
block layer. This is well explained in linux/fs.h:
WRITE: A normal async write. Device will be plugged.
WRITE_SYNC: Synchronous write. Identical to WRITE, but passes down
the hint that someone will be waiting on this IO
shortly.
WRITE_FLUSH: Like WRITE_SYNC but with preceding cache flush.
WRITE_FUA: Like WRITE_SYNC but data is guaranteed to be on
non-volatile media on completion.
In other words, SYNC does not *mean* that the write must be on stable storage
on completion. It just means that someone is waiting on us to complete the
write request. Thus triggering a ZIL commit for each SYNC write request on a
ZVOL is unnecessary and harmful for performance. To make matters worse, ZVOL
users have no way to express that they actually want data to be written to
stable storage, which means the ZIL is broken for ZVOLs.
The request for stable storage is expressed by the FUA flag, so we must
commit the ZIL after the write if the FUA flag is set. In addition, we must
commit the ZIL before the write if the FLUSH flag is set.
Also, we must inform the block layer that we actually support FLUSH and FUA.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The second argument of sops->show_options() was changed from a
'struct vfsmount *' to a 'struct dentry *'. Add an autoconf check
to detect the API change and then conditionally define the expected
interface. In either case we are only interested in the zfs_sb_t.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#549
Since the zpios and potentially other ZFS tests use the
DMU_OST_OTHER type to label their datasets, the zpool and
zfs commands should gracefully handle this type when it is
encountered. This patch modifies the commands' behavior
to ignore any datasets with a dds_type of DMU_OST_OTHER.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#536
Commit zfsonlinux/zfs@57a4eddc4d
allows the bootfs property to be set on any pool, but does not
accommodate subsequent vdev changes. For example:
# zpool replace rpool /dev/sda /dev/sdb
operation not supported on this type of pool
property 'bootfs' is not supported on EFI labeled devices
For non-Solaris builds, disable the check that emits this error.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
These libraries, which are an artifact of the ZoL development
process, conflict with packages that are already in distribution:
* libspl: SPL Programming Language
* libavl: AVL for Linux
* libefi: GRUB
And these libraries are potential conflicts:
* libshare: the Linux Mount Manager
* libunicode: Perl and Python
Recompose these five ZoL components into the four libraries that are
conventionally provided by Solaris and FreeBSD systems:
+ libnvpair
+ libuutil
+ libzpool
+ libzfs
This change resolves the name conflict, makes ZoL more compatible
with existing software that uses autotools to detect ZFS, and allows
pkg-zfs to better reflect the official Debian kFreeBSD packaging.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #430
Linux supports mounting over non-empty directories by default.
In Solaris this is not the case and -O option is required for
zfs mount to mount a zfs filesystem over a non-empty directory.
For compatibility, I've added support for -O option to mount
zfs filesystems over non-empty directories if the user wants
to, just like in Solaris.
I've defined MS_OVERLAY to record it in the flags variable if
the -O option is supplied. The flags variable passes through
a few functions and its checked before performing the empty
directory check in zfs_mount function. If -O is given, the
check is not performed.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#473
The Linux 3.1 kernel has introduced the concept of per-filesystem
shrinkers which are directly assoicated with a super block. Prior
to this change there was one shared global shrinker.
The zfs code relied on being able to call the global shrinker when
the arc_meta_limit was exceeded. This would cause the VFS to drop
references on a fraction of the dentries in the dcache. The ARC
could then safely reclaim the memory used by these entries and
honor the arc_meta_limit. Unfortunately, when per-filesystem
shrinkers were added the old interfaces were made unavailable.
This change adds support to use the new per-filesystem shrinker
interface so we can continue to honor the arc_meta_limit. The
major benefit of the new interface is that we can now target
only the zfs filesystem for dentry and inode pruning. Thus we
can minimize any impact on the caching of other filesystems.
In the context of making this change several other important
issues related to managing the ARC were addressed, they include:
* The dnlc_reduce_cache() function which was called by the ARC
to drop dentries for the Posix layer was replaced with a generic
zfs_prune_t callback. The ZPL layer now registers a callback to
drop these dentries removing a layering violation which dates
back to the Solaris code. This callback can also be used by
other ARC consumers such as Lustre.
arc_add_prune_callback()
arc_remove_prune_callback()
* The arc_reduce_dnlc_percent module option has been changed to
arc_meta_prune for clarity. The dnlc functions are specific to
Solaris's VFS and have already been largely eliminated already.
The replacement tunable now represents the number of bytes the
prune callback will request when invoked.
* Less aggressively invoke the prune callback. We used to call
this whenever we exceeded the arc_meta_limit however that's not
strictly correct since it results in over zeleous reclaim of
dentries and inodes. It is now only called once the arc_meta_limit
is exceeded and every effort has been made to evict other data from
the ARC cache.
* More promptly manage exceeding the arc_meta_limit. When reading
meta data in to the cache if a buffer was unable to be recycled
notify the arc_reclaim thread to invoke the required prune.
* Added arcstat_prune kstat which is incremented when the ARC
is forced to request that a consumer prune its cache. Remember
this will only occur when the ARC has no other choice. If it
can evict buffers safely without invoking the prune callback
it will.
* This change is also expected to resolve the unexpect collapses
of the ARC cache. This would occur because when exceeded just the
arc_meta_limit reclaim presure would be excerted on the arc_c
value via arc_shrink(). This effectively shrunk the entire cache
when really we just needed to reclaim meta data.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#466Closes#292
Directly changing inode->i_nlink is deprecated in Linux 3.2 by commit
SHA: bfe8684869601dacfcb2cd69ef8cfd9045f62170
Use the new set_nlink() kernel function instead.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes: #462
Added the necessary build infrastructure for building packages
compatible with the Arch Linux distribution. As such, one can now run:
$ ./configure
$ make pkg # Alternatively, one can run 'make arch' as well
on the Arch Linux machine to create two binary packages compatible with
the pacman package manager, one for the zfs userland utilities and
another for the zfs kernel modules. The new packages can then be
installed by running:
# pacman -U $package.pkg.tar.xz
In addition, source-only packages suitable for an Arch Linux chroot
environment or remote builder can also be build using the 'sarch' make
rule.
NOTE: Since the source dist tarball is created on the fly from the head
of the build tree, it's MD5 hash signature will be continually influx.
As a result, the md5sum variable was intentionally omitted from the
PKGBUILD files, and the '--skipinteg' makepkg option is used. This may
or may not have any serious security implications, as the source tarball
is not being downloaded from an outside source.
Signed-off-by: Prakash Surya <surya1@llnl.gov>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#491
While setting/getting userquota and groupquota properties, the input
was not treated as a possible username or groupname if it had a
leading digit. While useradd in linux recommends the regexp
[a-z_][a-z0-9_-]*[$]? , it is not enforced. This causes problem for
usernames with leading digits in them. We need to be able to support
getting and setting properties for this unconventional but possible
input category
I've updated the code to validate the username or groupname directly
via the API. Also, note that I moved this validation to the beginning
before the check for SID names with @. This also supports usernames
with @ character in them which are valid. Only when input with @ is
not a valid username, it is interpreted as a potential SID name.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#428
While we initially allowed you to set your ashift as large as 17
(SPA_MAXBLOCKSIZE) that is actually unsafe. What wasn't considered
at the time is that each uberblock written to the vdev label ring
buffer will be of this size. Now the buffer is statically sized
to 128k and we need to be able to fit several uberblocks in it.
With a large ashift that becomes a problem.
Therefore I'm reducing the maximum configurable ashift value to 12.
This is large enough for the 4k sector drives and small enough that
we can still keep the most recent 32 uberblock in the vdev label
ring buffer.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#425
Update the code to use the bdi_setup_and_register() helper to
simplify the bdi integration code. The updated code now just
registers the bdi during mount and destroys it during unmount.
The only complication is that for 2.6.32 - 2.6.33 kernels the
helper wasn't available so in these cases the zfs code must
provide it. Luckily the bdi_setup_and_register() function
is trivial.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#367
For a long time now the kernel has been moving away from using the
pdflush daemon to write 'old' dirty pages to disk. The primary reason
for this is because the pdflush daemon is single threaded and can be
a limiting factor for performance. Since pdflush sequentially walks
the dirty inode list for each super block any delay in processing can
slow down dirty page writeback for all filesystems.
The replacement for pdflush is called bdi (backing device info). The
bdi system involves creating a per-filesystem control structure each
with its own private sets of queues to manage writeback. The advantage
is greater parallelism which improves performance and prevents a single
filesystem from slowing writeback to the others.
For a long time both systems co-existed in the kernel so it wasn't
strictly required to implement the bdi scheme. However, as of
Linux 2.6.36 kernels the pdflush functionality has been retired.
Since ZFS already bypasses the page cache for most I/O this is only
an issue for mmap(2) writes which must go through the page cache.
Even then adding this missing support for newer kernels was overlooked
because there are other mechanisms which can trigger writeback.
However, there is one critical case where not implementing the bdi
functionality can cause problems. If an application handles a page
fault it can enter the balance_dirty_pages() callpath. This will
result in the application hanging until the number of dirty pages in
the system drops below the dirty ratio.
Without a registered backing_device_info for the filesystem the
dirty pages will not get written out. Thus the application will hang.
As mentioned above this was less of an issue with older kernels because
pdflush would eventually write out the dirty pages.
This change adds a backing_device_info structure to the zfs_sb_t
which is already allocated per-super block. It is then registered
when the filesystem mounted and unregistered on unmount. It will
not be registered for mounted snapshots which are read-only. This
change will result in flush-<pool> thread being dynamically created
and destroyed per-mounted filesystem for writeback.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#174
Simply closing the stdout and/or stderr file descriptors for
the child process can have bad side effects if for example
the child writes to stdout/stderr after open()ing a file.
The open() call might have returned the same file descriptor
one would usually expect for stdout/stderr (1 and 2), thereby
causing mis-directed writes.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #190
Add a "REFRATIO" property, which is the compression ratio based on
data referenced. For snapshots, this is the same as COMPRESSRATIO,
but for filesystems/volumes, the COMPRESSRATIO is based on the
data "USED" (ie, includes blocks in children, but not blocks
shared with the origin).
This is needed to figure out how much space a filesystem would
use if it were not compressed (ignoring snapshots).
Reviewed by: George Wilson <George.Wilson@delphix.com>
Reviewed by: Adam Leventhal <Adam.Leventhal@delphix.com>
Reviewed by: Dan McDonald <danmcd@nexenta.com>
Reviewed by: Richard Elling <richard.elling@richardelling.com>
Reviewed by: Mark Musante <Mark.Musante@oracle.com>
Reviewed by: Garrett D'Amore <garrett@nexenta.com>
Approved by: Garrett D'Amore <garrett@nexenta.com>
References to Illumos issue and patch:
- https://www.illumos.org/issues/1092
- https://github.com/illumos/illumos-gate/commit/187d6ac08a
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Issue #340
Unlike most other Linux distributions archlinux installs its
init scripts in /etc/rc.d insead of /etc/init.d. This commit
provides an archlinux rc.d script for zfs and extends the
build infrastructure to ensure it get's installed in the
correct place.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#322
The zfs libraries were never properly versioned. Since the API has
remained static for quite some time this we never an issue. However,
going forward they should be versioned. This commit versions all
of the libraries to 1.0.0. From here on out this version must be
updated to reflect changes to the library.
Drop usage of dlopen/dlsym for libshare. There is no need to do
this because the zfs packages provide libshare. Unlike on Solaris
we are guaranteed it will be available.
This avoids possible problems with hardcoding the libshare path in
the code (e.g. when users specify a different install path via
configure options). It additionally simplifies the code which is
good for maintainability.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The sharenfs and sharesmb properties depend on the libshare library
to export datasets via NFS and SMB. This commit implements the base
libshare functionality as well as support for managing NFS shares.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The .get_sb callback has been replaced by a .mount callback
in the file_system_type structure. When using the new
interface the caller must now use the mount_nodev() helper.
Unfortunately, the new interface no longer passes the vfsmount
down to the zfs layers. This poses a problem for the existing
implementation because we currently save this pointer in the
super block for latter use. It provides our only entry point
in to the namespace layer for manipulating certain mount options.
This needed to be done originally to allow commands like
'zfs set atime=off tank' to work properly. It also allowed me
to keep more of the original Solaris code unmodified. Under
Solaris there is a 1-to-1 mapping between a mount point and a
file system so this is a fairly natural thing to do. However,
under Linux they many be multiple entries in the namespace
which reference the same filesystem. Thus keeping a back
reference from the filesystem to the namespace is complicated.
Rather than introduce some ugly hack to get the vfsmount and
continue as before. I'm leveraging this API change to update
the ZFS code to do things in a more natural way for Linux.
This has the upside that is resolves the compatibility issue
for the long term and fixes several other minor bugs which
have been reported.
This commit updates the code to remove this vfsmount back
reference entirely. All modifications to filesystem mount
options are now passed in to the kernel via a '-o remount'.
This is the expected Linux mechanism and allows the namespace
to properly handle any options which apply to it before passing
them on to the file system itself.
Aside from fixing the compatibility issue, removing the
vfsmount has had the benefit of simplifying the code. This
change which fairly involved has turned out nicely.
Closes#246Closes#217Closes#187Closes#248Closes#231
The security_inode_init_security() function now takes an additional
qstr argument which must be passed in from the dentry if available.
Passing a NULL is safe when no qstr is available the relevant
security checks will just be skipped.
Closes#246Closes#217Closes#187
The inode eviction should unmap the pages associated with the inode.
These pages should also be flushed to disk to avoid the data loss.
Therefore, use truncate_setsize() in evict_inode() to release the
pagecache.
The API truncate_setsize() was added in 2.6.35 kernel. To ensure
compatibility with the old kernel, the patch defines its own
truncate_setsize function.
Signed-off-by: Prasad Joshi <pjoshi@stec-inc.com>
Closes#255
Some disks with internal sectors larger than 512 bytes (e.g., 4k) can
suffer from bad write performance when ashift is not configured
correctly. This is caused by the disk not reporting its actual sector
size, but a sector size of 512 bytes. The drive may behave this way
for compatibility reasons. For example, the WDC WD20EARS disks are
known to exhibit this behavior.
When creating a zpool, ZFS takes that wrong sector size and sets the
"ashift" property accordingly (to 9: 1<<9=512), whereas it should be
set to 12 for 4k sectors (1<<12=4096).
This patch allows an adminstrator to manual specify the known correct
ashift size at 'zpool create' time. This can significantly improve
performance in certain cases. However, it will have an impact on your
total pool capacity. See the updated ashift property description
in the zpool.8 man page for additional details.
Valid values for the ashift property range from 9 to 17 (512B-128KB).
Additionally, you may set the ashift to 0 if you wish to auto-detect
the sector size based on what the disk reports, this is the default
behavior. The most common ashift values are 9 and 12.
Example:
zpool create -o ashift=12 tank raidz2 sda sdb sdc sdd
Closes#280
Original-patch-by: Richard Laager <rlaager@wiktel.com>
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The previous commit 8a7e1ceefa wasn't
quite right. This check applies to both the user and kernel space
build and as such we must make sure it runs regardless of what
the --with-config option is set too.
For example, if --with-config=kernel then the autoconf test does
not run and we generate build warnings when compiling the kernel
packages.
Gcc versions 4.3.2 and earlier do not support the compiler flag
-Wno-unused-but-set-variable. This can lead to build failures
on older Linux platforms such as Debian Lenny. Since this is
an optional build argument this changes add a new autoconf check
for the option. If it is supported by the installed version of
gcc then it is used otherwise it is omited.
See commit's 12c1acde76 and
79713039a2 for the reason the
-Wno-unused-but-set-variable options was originally added.
Sending pools with dedup results in a segfault due to a Solaris
portability issue. Under Solaris the pipe(2) library call
creates a bidirectional data channel. Unfortunately, on Linux
pipe(2) call creates unidirection data channel. The fix is to
use the socketpair(2) function to create the expected
bidirectional channel.
Seth Heeren did the original leg work on this issue for zfs-fuse.
We finally just rediscovered the same portability issue and
dfurphy was able to point me at the original issue for the fix.
Closes#268
This change fixes a kernel panic which would occur when resizing
a dataset which was not open. The objset_t stored in the
zvol_state_t will be set to NULL when the block device is closed.
To avoid this issue we pass the correct objset_t as the third arg.
The code has also been updated to correctly notify the kernel
when the block device capacity changes. For 2.6.28 and newer
kernels the capacity change will be immediately detected. For
earlier kernels the capacity change will be detected when the
device is next opened. This is a known limitation of older
kernels.
Online ext3 resize test case passes on 2.6.28+ kernels:
$ dd if=/dev/zero of=/tmp/zvol bs=1M count=1 seek=1023
$ zpool create tank /tmp/zvol
$ zfs create -V 500M tank/zd0
$ mkfs.ext3 /dev/zd0
$ mkdir /mnt/zd0
$ mount /dev/zd0 /mnt/zd0
$ df -h /mnt/zd0
$ zfs set volsize=800M tank/zd0
$ resize2fs /dev/zd0
$ df -h /mnt/zd0
Original-patch-by: Fajar A. Nugraha <github@fajar.net>
Closes#68Closes#84
Disable the gethostid() override for Solaris behavior because Linux systems
implement the POSIX standard in a way that allows a negative result.
Mask the gethostid() result to the lower four bytes, like coreutils does in
/usr/bin/hostid, to prevent junk bits or sign-extension on systems that have an
eight byte long type. This can cause a spurious hostid mismatch that prevents
zpool import on 64-bit systems.
As of gcc-4.6 the option -Wunused-but-set-variable is enabled by
default. While this is a useful warning there are numerous places
in the ZFS code when a variable is set and then only checked in an
ASSERT(). To avoid having to update every instance of this in the
code we now set -Wno-unused-but-set-variable to suppress the warning.
Additionally, when building with --enable-debug and -Werror set these
warning also become fatal. We can reevaluate the suppression of these
error at a later time if it becomes an issue. For now we are basically
just reverting to the previous gcc behavior.
Added insert_inode_locked() helper function, prior to this most callers
used insert_inode_hash(). The older method doesn't check for collisions
in the inode_hashtable but it still acceptible for use. Fallback to
using insert_inode_hash() when insert_inode_locked() is unavailable.
Compiling with 'LDFLAGS=-Wl,--as-needed' exposed the fact that
there were some library linking problems introduced by mount_zfs.
In particular, the libzfs library does use nvpair symbols, and
mount_zfs contains no dependencies on libzpool.
Closes#161Closes#162
To support automatically mounting your zfs on filesystem on boot
a basic init script is needed. Unfortunately, every distribution
has their own idea of the _right_ way to do things. Rather than
write one very complicated portable init script, which would be
invariably replaced by the distributions own anyway. I have
instead added support to provide multiple distribution specific
init scripts.
The correct init script for your distribution will be selected
by ZFS_AC_DEFAULT_PACKAGE which will set DEFAULT_INIT_SCRIPT.
During 'make install' the correct script for your system will
be installed from zfs/etc/init.d/zfs.DEFAULT_INIT_SCRIPT to the
usual /etc/init.d/zfs location.
Currently, there is zfs.fedora and a more generic zfs.lsb init
script. Hopefully, the distribution maintainers who know best
how they want their init scripts to function will feedback their
approved versions to be included in the project.
This change does not consider upstart jobs but I'm not at all
opposed to add that sort of thing.
Because we are dependent of the system mount/umount utilities to
ensure correct mtab locking, we should not suppress their error
output. During a successful mount/umount they will be silent,
but during a failure the error message they print is the only sure
way to know why a mount failed. This is because the (u)mount(8)
return code does not contain the result of the system call issued.
The only way to clearly idenify why thing failed is to rely on
the error message printed by the tool.
Longer term once libmount is available we can issue the mount/umount
system calls within the tool and still be ensured correct mtab locking.
Closed#107
Several issues related to strange mount/umount behavior were reported
and this commit should address most of them. The original idea was
to put in place a zfs mount helper (mount.zfs). This helper is used
to enforce 'legacy' mount behavior, and perform any extra mount argument
processing (selinux, zfsutil, etc). This helper wasn't ready for the
0.6.0-rc1 release but with this change it's functional but needs to
extensively tested.
This change addresses the following open issues.
Closes#101Closes#107Closes#113Closes#115Closes#119
The libspl and libzpool libraries were missing from the libzfs
Makefile.am. They should be explicitly listed to avoid build
issues when compiling static libraries and binaries.
Additionally, ensure libzpool is built before libzfs because
libzfs is dependent on libzpool. This was also exposed as an
issue when forcing static linking.
The open_bdev_exclusive() function has been replaced (again) by the
more generic blkdev_get_by_path() function. Additionally, the
counterpart function close_bdev_exclusive() has been replaced by
blkdev_put(). Because these functions are more generic versions
of the functions they replaced the compatibility macro must add
the FMODE_EXCL mask to ensure they are exclusive.
Closes#114
There are three improvements here to 'zpool import' proposed by Fajar
in Github issue #98. They are all good so I'm commiting all three.
1) Add descriptions for "hpet" and "core" blacklist entries.
2) Add "core" to the blacklist, as described in the issue accessing
this device will crash Xen dom0.
3) Refine probing behavior to use fstatat64(). This allows us to
determine if a device is a block device or a regular file without
having to open it. This is the safest appraoch when probing /dev/
because the simple act of opening a device may have unexpected
consequences.
Closes#98
Until code is added to support automatically sharing datasets
we should return success instead of failure. This prevents the
command line tools from returning a non-zero error code. While
a user likely won't notice this, test scripts like zconfig.sh
do and correctly fail because of it.
The new prefered inteface for evicting an inode from the inode cache
is the ->evict_inode() callback. It replaces both the ->delete_inode()
and ->clear_inode() callbacks which were previously used for this.
The fsync() callback in the file_operations structure used to take
3 arguments. The callback now only takes 2 arguments because the
dentry argument was determined to be unused by all consumers. To
handle this a compatibility prototype was added to ensure the right
prototype is used. Our implementation never used the dentry argument
either so it's just a matter of using the right prototype.
The const keyword was added to the 'struct xattr_handler' in the
generic Linux super_block structure. To handle this we define an
appropriate xattr_handler_t typedef which can be used. This was
the preferred solution because it keeps the code clean and readable.
The inclusion on dlsym(), dlopen(), and dlclose() symbols require
us to link against the dl library. Be careful to add the flag to
both the libzfs library and the commands which depend on the library.
ZFS even under Solaris does not strictly require libshare to be
available. The current implementation attempts to dlopen() the
library to access the needed symbols. If this fails libshare
support is simply disabled.
This means that on Linux we only need the most minimal libshare
implementation. In fact just enough to prevent the build from
failing. Longer term we can decide if we want to implement a
libshare library like Solaris. At best this would be an abstraction
layer between ZFS and NFS/SMB. Alternately, we can drop libshare
entirely and directly integrate ZFS with Linux's NFS/SMB.
Finally the bare bones user-libshare.m4 test was dropped. If we
do decide to implement libshare at some point it will surely be
as part of this package so the check is not needed.
By design the zfs utility is supposed to handle mounting and unmounting
a zfs filesystem. We could allow zfs to do this directly. There are
system calls available to mount/umount a filesystem. And there are
library calls available to manipulate /etc/mtab. But there are a
couple very good reasons not to take this appraoch... for now.
Instead of directly calling the system and library calls to (u)mount
the filesystem we fork and exec a (u)mount process. The principle
reason for this is to delegate the responsibility for locking and
updating /etc/mtab to (u)mount(8). This ensures maximum portability
and ensures the right locking scheme for your version of (u)mount
will be used. If we didn't do this we would have to resort to an
autoconf test to determine what locking mechanism is used.
The downside to using mount(8) instead of mount(2) is that we lose
the exact errno which was returned by the kernel. The return code
from mount(8) provides some insight in to what went wrong but it
not quite as good. For the moment this is translated as a best
guess in to a errno for the higher layers of zfs.
In the long term a shared library called libmount is under development
which provides a common API to address the locking and errno issues.
Once the standard mount utility has been updated to use this library
we can then leverage it. Until then this is the only safe solution.
http://www.kernel.org/pub/linux/utils/util-linux/libmount-docs/index.html
Recently helper functions were added to libzfs_util to load a kernel
module or execute a process. Initially this functionality was limited
to libzfs but it has become clear there will be other consumers. This
change opens up the interface so it may be used where appropriate.
If libselinux is detected on your system at configure time link
against it. This allows us to use a library call to detect if
selinux is enabled and if it is to pass the mount option:
"context=\"system_u:object_r:file_t:s0"
For now this is required because none of the existing selinux
policies are aware of the zfs filesystem type. Because of this
they do not properly enable xattr based labeling even though
zfs supports all of the required hooks.
Until distro's add zfs as a known xattr friendly fs type we
must use mntpoint labeling. Alternately, end users could modify
their existing selinux policy with a little guidance.
These compiler warnings were introduced when code which was
previously #ifdef'ed out by HAVE_ZPL was re-added for use
by the posix layer. All of the following changes should be
obviously correct and will cause no semantic changes.
If libblkid does not contain ZFS support, then 'zpool import' will scan
all block devices in /dev/ to determine which ones are components of a
ZFS filesystem. It does this by opening all the devices and stat'ing
them to determine which ones are block devices. If the device turns
out not to be a block device it is skipped.
Usually, this whole process is pretty harmless (although slow). But
there are certain devices in /dev/ which must be handled in a very
specific way or your system may crash. For example, if /dev/watchdog
is simply opened the watchdog timer will be started and your system
will panic when the timer expires.
It turns out the /dev/hpet causes similiar problems although only when
accessed under a virtual machine. For some reason accessing /dev/hpet
causes qemu to crash. To address this issue this commit adds /dev/hpet
to the device blacklist, it will be skipped solely based on its name.
Some sudo configurations may not include /sbin in the PATH.
libzfs_load_module() currently does not call modprobe with an absolute path, so
it may fail under such configurations if called under sudo. This change adds
the absolute path to modprobe so we no longer rely on how PATH is set.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
zpool status displays abbreviated vdev names without leading path components
and, in the case of whole disks, without partition information. Also, the
zpool subcommands 'create' and 'add' support using shorthand devices names
without qualified paths. Prior to this change, however, removing a device
generally required specifying its name as it is stored in the vdev label. So
while zpool status might list a cache disk with a name like A16, removing it
would require a full path such as /dev/disk/zpool/A16-part1, which is
non-intuitive.
This change adds support for shorthand device names with the remove subcommand
so one can simply type, for example,
zpool remove tank A16
A consequence of this change is that including the partition information when
removing a whole-disk vdev now results in an error. While this is arguably the
correct behavior, it is a departure from how zpool previously worked in this
project.
This change removes the only reference to ctd_check_path(), so that function is
also removed to avoid compiler warnings.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This change adds two helper functions for working with vdev names and paths.
zfs_resolve_shortname() resolves a shorthand vdev name to an absolute path
of a file in /dev, /dev/disk/by-id, /dev/disk/by-label, /dev/disk/by-path,
/dev/disk/by-uuid, /dev/disk/zpool. This was previously done only in the
function is_shorthand_path(), but we need a general helper function to
implement shorthand names for additional zpool subcommands like remove.
is_shorthand_path() is accordingly updated to call the helper function.
There is a minor change in the way zfs_resolve_shortname() tests if a file
exists. is_shorthand_path() effectively used open() and stat64() to test for
file existence, since its scope includes testing if a device is a whole disk
and collecting file status information. zfs_resolve_shortname(), on the other
hand, only uses access() to test for existence and leaves it to the caller to
perform any additional file operations. This seemed like the most general and
lightweight approach, and still preserves the semantics of is_shorthand_path().
zfs_append_partition() appends a partition suffix to a device path. This
should be used to generate the name of a whole disk as it is stored in the vdev
label. The user-visible names of whole disks do not contain the partition
information, while the name in the vdev label does. The code was lifted from
the function make_disks(), which now just calls the helper function. Again,
having a helper function to do this supports general handling of shorthand
names in the user interface.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
ZFS works best when it is notified as soon as possible when a device
failure occurs. This allows it to immediately start any recovery
actions which may be needed. In theory Linux supports a flag which
can be set on bio's called FAILFAST which provides this quick
notification by disabling the retry logic in the lower scsi layers.
That's the theory at least. In practice is turns out that while the
flag exists you oddly have to set it with the BIO_RW_AHEAD flag.
And even when it's set it you may get retries in the low level
drivers decides that's the right behavior, or if you don't get the
right error codes reported to the scsi midlayer.
Unfortunately, without additional kernels patchs there's not much
which can be done to improve this. Basically, this just means that
it may take 2-3 minutes before a ZFS is notified properly that a
device has failed. This can be improved and I suspect I'll be
submitting patches upstream to handle this.
This commit modifies libzfs_init() to attempt to load the zfs kernel module if
it is not already loaded. This is done to simplify initialization by letting
users simply import their zpools without having to first load the module.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Under Solaris, the slice number is chopped off when displaying the device name
if the vdev is a whole disk. Under Linux we should similarly discard the
partition number. This commit adds the logic to perform the name truncation
for devices ending in -partX, XpX, or X, where X is a string of digits. The
second case handles devices like md0p0. The third case is limited to scsi and
ide disks, i.e. those beginning with "sd" or "hd", in order to avoid stripping
the number from names like "loop0".
This commit removes the Solaris-specific code for removing slices, since we no
longer reasonably expect our changes to be merged in upstream. The partition
stripping code was moved off to a helper function to improve readability.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Top-level vdev names in zpool status output should follow a <type-id> naming
convention. In the case of raidz devices, the type portion of the name was
missing.
This commit fixes a bug in zpool_vdev_name() where in this snprintf call
(void) snprintf(buf, sizeof (buf), "%s-%llu", path,
(u_longlong_t)id);
buf and path may point to the same location. The result is that buf ends up
containing only the "-id" part. This only occurred for raidz devices because
the code for appending the parity level to the type string stored its result in
buf then set path to point there. To fix this we allocate a new temporary
buffer on the stack instead of reusing buf.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Closes#57
One of the neat tricks an autoconf style project is capable of
is allow configurion/building in a directory other than the
source directory. The major advantage to this is that you can
build the project various different ways while making changes
in a single source tree.
For example, this project is designed to work on various different
Linux distributions each of which work slightly differently. This
means that changes need to verified on each of those supported
distributions perferably before the change is committed to the
public git repo.
Using nfs and custom build directories makes this much easier.
I now have a single source tree in nfs mounted on several different
systems each running a supported distribution. When I make a
change to the source base I suspect may break things I can
concurrently build from the same source on all the systems each
in their own subdirectory.
wget -c http://github.com/downloads/behlendorf/zfs/zfs-x.y.z.tar.gz
tar -xzf zfs-x.y.z.tar.gz
cd zfs-x-y-z
------------------------- run concurrently ----------------------
<ubuntu system> <fedora system> <debian system> <rhel6 system>
mkdir ubuntu mkdir fedora mkdir debian mkdir rhel6
cd ubuntu cd fedora cd debian cd rhel6
../configure ../configure ../configure ../configure
make make make make
make check make check make check make check
This change also moves many of the include headers from individual
incude/sys directories under the modules directory in to a single
top level include directory. This has the advantage of making
the build rules cleaner and logically it makes a bit more sense.
Add the initial products from autogen.sh. These products will
be updated incrementally after this point as development occurs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch contains required changes to the user space
utilities to allow them to integrate cleanly with Linux.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch contains all the changes needed to integrate the user
side zfs tools with Linux style devices. Primarily this includes fixing
up the Solaris libefi library to be Linux friendly, and integrating with
the libblkid library which is provided by e2fsprogs.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Track various large hunks which have been dropped simply
because they are not relevant to this port.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Solaris recently introduced the idea of drive topology because
where a drive is located does matter. I have already handled
this with udev/blkid integration under Linux so I'm hopeful
this case can simply be removed but for now I've just stubbed
out what is needed in libspl and commented out the rest here.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The upstream ZFS code has correctly moved to a faster native sha2
implementation. Unfortunately, under Linux that's going to be a little
problematic so we revert the code to the more portable version contained
in earlier ZFS releases. Using the native sha2 implementation in Linux
is possible but the API is slightly different in kernel version user
space depending on which libraries are used. Ideally, we need a fast
implementation of SHA256 which builds as part of ZFS this shouldn't be
that hard to do but it will take some effort.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This branch contains the majority of the changes required to cleanly
intergrate with Linux style special devices (/dev/zfs). Mainly this
means dropping all the Solaris style callbacks and replacing them
with the Linux equivilants.
This patch also adds the onexit infrastructure needed to track
some minimal state between ioctls. Under Linux it would be easy
to do this simply using the file->private_data. But under Solaris
they apparent need to pass the file descriptor as part of the ioctl
data and then perform a lookup in the kernel. Once again to keep
code change to a minimum I've implemented the Solaris solution.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
The ZFS update to onnv_141 brought with it support for a
security label attribute called mlslabel. This feature
depends on zones to work correctly and thus I am disabling
it under Linux. Equivilant functionality could be added
at some point in the future.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
This topic branch leverages the Solaris style FMA call points
in ZFS to create a user space visible event notification system
under Linux. This new system is called zevent and it unifies
all previous Solaris style ereports and sysevent notifications.
Under this Linux specific scheme when a sysevent or ereport event
occurs an nvlist describing the event is created which looks almost
exactly like a Solaris ereport. These events are queued up in the
kernel when they occur and conditionally logged to the console.
It is then up to a user space application to consume the events
and do whatever it likes with them.
To make this possible the existing /dev/zfs ABI has been extended
with two new ioctls which behave as follows.
* ZFS_IOC_EVENTS_NEXT
Get the next pending event. The kernel will keep track of the last
event consumed by the file descriptor and provide the next one if
available. If no new events are available the ioctl() will block
waiting for the next event. This ioctl may also be called in a
non-blocking mode by setting zc.zc_guid = ZEVENT_NONBLOCK. In the
non-blocking case if no events are available ENOENT will be returned.
It is possible that ESHUTDOWN will be returned if the ioctl() is
called while module unloading is in progress. And finally ENOMEM
may occur if the provided nvlist buffer is not large enough to
contain the entire event.
* ZFS_IOC_EVENTS_CLEAR
Clear are events queued by the kernel. The kernel will keep a fairly
large number of recent events queued, use this ioctl to clear the
in kernel list. This will effect all user space processes consuming
events.
The zpool command has been extended to use this events ABI with the
'events' subcommand. You may run 'zpool events -v' to output a
verbose log of all recent events. This is very similar to the
Solaris 'fmdump -ev' command with the key difference being it also
includes what would be considered sysevents under Solaris. You
may also run in follow mode with the '-f' option. To clear the
in kernel event queue use the '-c' option.
$ sudo cmd/zpool/zpool events -fv
TIME CLASS
May 13 2010 16:31:15.777711000 ereport.fs.zfs.config.sync
class = "ereport.fs.zfs.config.sync"
ena = 0x40982b7897700001
detector = (embedded nvlist)
version = 0x0
scheme = "zfs"
pool = 0xed976600de75dfa6
(end detector)
time = 0x4bec8bc3 0x2e5aed98
pool = "zpios"
pool_guid = 0xed976600de75dfa6
pool_context = 0x0
While the 'zpool events' command is handy for interactive debugging
it is not expected to be the primary consumer of zevents. This ABI
was primarily added to facilitate the addition of a user space
monitoring daemon. This daemon would consume all events posted by
the kernel and based on the type of event perform an action. For
most events simply forwarding them on to syslog is likely enough.
But this interface also cleanly allows for more sophisticated
actions to be taken such as generating an email for a failed drive.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Add autoconf style build infrastructure to the ZFS tree. This
includes autogen.sh, configure.ac, m4 macros, some scripts/*,
and makefiles for all the core ZFS components.
This look like a typo. The intention was to use strlcat() however
strncat() was used instead accidentally this may lead to a buffer
overflow. This was caught by gcc -D_FORTIFY_SOURCE=2.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Remove deadcode. It's possible the code should be in use
somewhere, but as the source code is laid out it currently
is not.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Use constructor attribute on non-Solaris platforms.
The #pragma init/fini ->__attribute__((constructor/destructor))
conversions, these should go upstream.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Fix non-c90 compliant code, for the most part these changes
simply deal with where a particular variable is declared.
Under c90 it must alway be done at the very start of a block.
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Richard Yao
Brian Behlendorf
Ned A. Bass
Richard Laager
Ned Bass
Richard Yao
Etienne Dechamps
Prakash Surya
Darik Horn
Suman Chakravartula
Suman Chakravartula
Gunnar Beutner
Alexander Stetsenko
Matt Ahrens
Kyle Fuller
Prasad Joshi
Christian Kohlschütter